pcmcia: introduce autoconfiguration feature
Introduce an autoconfiguration feature to set certain values in
pcmcia_loop_config(), instead of copying the same code over and over
in each PCMCIA driver. At first, introduce the following options:
CONF_AUTO_CHECK_VCC check or matching Vcc entry
CONF_AUTO_SET_VPP set Vpp
CONF_AUTO_AUDIO enable the speaker line
CC: netdev@vger.kernel.org
CC: linux-wireless@vger.kernel.org
CC: linux-ide@vger.kernel.org
CC: linux-usb@vger.kernel.org
CC: laforge@gnumonks.org
CC: linux-mtd@lists.infradead.org
CC: alsa-devel@alsa-project.org
CC: linux-serial@vger.kernel.org
CC: Jiri Kosina <jkosina@suse.cz>
CC: linux-scsi@vger.kernel.org
Acked-by: Gustavo F. Padovan <padovan@profusion.mobi> (for drivers/bluetooth)
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
diff --git a/drivers/isdn/hisax/sedlbauer_cs.c b/drivers/isdn/hisax/sedlbauer_cs.c
index 791e23a..b69eccf 100644
--- a/drivers/isdn/hisax/sedlbauer_cs.c
+++ b/drivers/isdn/hisax/sedlbauer_cs.c
@@ -164,33 +164,11 @@
static int sedlbauer_config_check(struct pcmcia_device *p_dev,
cistpl_cftable_entry_t *cfg,
cistpl_cftable_entry_t *dflt,
- unsigned int vcc,
void *priv_data)
{
if (cfg->index == 0)
return -ENODEV;
- /* Does this card need audio output? */
- if (cfg->flags & CISTPL_CFTABLE_AUDIO)
- p_dev->config_flags |= CONF_ENABLE_SPKR;
-
- /* Use power settings for Vcc and Vpp if present */
- /* Note that the CIS values need to be rescaled */
- if (cfg->vcc.present & (1<<CISTPL_POWER_VNOM)) {
- if (vcc != cfg->vcc.param[CISTPL_POWER_VNOM]/10000)
- return -ENODEV;
- } else if (dflt->vcc.present & (1<<CISTPL_POWER_VNOM)) {
- if (vcc != dflt->vcc.param[CISTPL_POWER_VNOM]/10000)
- return -ENODEV;
- }
-
- if (cfg->vpp1.present & (1<<CISTPL_POWER_VNOM))
- p_dev->vpp = cfg->vpp1.param[CISTPL_POWER_VNOM]/10000;
- else if (dflt->vpp1.present & (1<<CISTPL_POWER_VNOM))
- p_dev->vpp = dflt->vpp1.param[CISTPL_POWER_VNOM]/10000;
-
- p_dev->config_flags |= CONF_ENABLE_IRQ;
-
/* IO window settings */
p_dev->resource[0]->end = p_dev->resource[1]->end = 0;
if ((cfg->io.nwin > 0) || (dflt->io.nwin > 0)) {
@@ -223,6 +201,9 @@
dev_dbg(&link->dev, "sedlbauer_config(0x%p)\n", link);
+ link->config_flags |= CONF_ENABLE_IRQ | CONF_AUTO_CHECK_VCC |
+ CONF_AUTO_SET_VPP | CONF_AUTO_AUDIO;
+
/*
In this loop, we scan the CIS for configuration table entries,
each of which describes a valid card configuration, including