| /** |
| * This file contains definitions of WLAN commands. |
| */ |
| |
| #ifndef _LBS_HOST_H_ |
| #define _LBS_HOST_H_ |
| |
| /** PUBLIC DEFINITIONS */ |
| #define DEFAULT_AD_HOC_CHANNEL 6 |
| #define DEFAULT_AD_HOC_CHANNEL_A 36 |
| |
| /** IEEE 802.11 oids */ |
| #define OID_802_11_SSID 0x00008002 |
| #define OID_802_11_INFRASTRUCTURE_MODE 0x00008008 |
| #define OID_802_11_FRAGMENTATION_THRESHOLD 0x00008009 |
| #define OID_802_11_RTS_THRESHOLD 0x0000800A |
| #define OID_802_11_TX_ANTENNA_SELECTED 0x0000800D |
| #define OID_802_11_SUPPORTED_RATES 0x0000800E |
| #define OID_802_11_STATISTICS 0x00008012 |
| #define OID_802_11_TX_RETRYCOUNT 0x0000801D |
| #define OID_802_11D_ENABLE 0x00008020 |
| |
| #define CMD_OPTION_WAITFORRSP 0x0002 |
| |
| /** Host command IDs */ |
| |
| /* Return command are almost always the same as the host command, but with |
| * bit 15 set high. There are a few exceptions, though... |
| */ |
| #define CMD_RET(cmd) (0x8000 | cmd) |
| |
| /* Return command convention exceptions: */ |
| #define CMD_RET_802_11_ASSOCIATE 0x8012 |
| |
| /* Command codes */ |
| #define CMD_GET_HW_SPEC 0x0003 |
| #define CMD_EEPROM_UPDATE 0x0004 |
| #define CMD_802_11_RESET 0x0005 |
| #define CMD_802_11_SCAN 0x0006 |
| #define CMD_802_11_GET_LOG 0x000b |
| #define CMD_MAC_MULTICAST_ADR 0x0010 |
| #define CMD_802_11_AUTHENTICATE 0x0011 |
| #define CMD_802_11_EEPROM_ACCESS 0x0059 |
| #define CMD_802_11_ASSOCIATE 0x0050 |
| #define CMD_802_11_SET_WEP 0x0013 |
| #define CMD_802_11_GET_STAT 0x0014 |
| #define CMD_802_3_GET_STAT 0x0015 |
| #define CMD_802_11_SNMP_MIB 0x0016 |
| #define CMD_MAC_REG_MAP 0x0017 |
| #define CMD_BBP_REG_MAP 0x0018 |
| #define CMD_MAC_REG_ACCESS 0x0019 |
| #define CMD_BBP_REG_ACCESS 0x001a |
| #define CMD_RF_REG_ACCESS 0x001b |
| #define CMD_802_11_RADIO_CONTROL 0x001c |
| #define CMD_802_11_RF_CHANNEL 0x001d |
| #define CMD_802_11_RF_TX_POWER 0x001e |
| #define CMD_802_11_RSSI 0x001f |
| #define CMD_802_11_RF_ANTENNA 0x0020 |
| #define CMD_802_11_PS_MODE 0x0021 |
| #define CMD_802_11_DATA_RATE 0x0022 |
| #define CMD_RF_REG_MAP 0x0023 |
| #define CMD_802_11_DEAUTHENTICATE 0x0024 |
| #define CMD_802_11_REASSOCIATE 0x0025 |
| #define CMD_802_11_DISASSOCIATE 0x0026 |
| #define CMD_MAC_CONTROL 0x0028 |
| #define CMD_802_11_AD_HOC_START 0x002b |
| #define CMD_802_11_AD_HOC_JOIN 0x002c |
| #define CMD_802_11_QUERY_TKIP_REPLY_CNTRS 0x002e |
| #define CMD_802_11_ENABLE_RSN 0x002f |
| #define CMD_802_11_SET_AFC 0x003c |
| #define CMD_802_11_GET_AFC 0x003d |
| #define CMD_802_11_AD_HOC_STOP 0x0040 |
| #define CMD_802_11_HOST_SLEEP_CFG 0x0043 |
| #define CMD_802_11_WAKEUP_CONFIRM 0x0044 |
| #define CMD_802_11_HOST_SLEEP_ACTIVATE 0x0045 |
| #define CMD_802_11_BEACON_STOP 0x0049 |
| #define CMD_802_11_MAC_ADDRESS 0x004d |
| #define CMD_802_11_LED_GPIO_CTRL 0x004e |
| #define CMD_802_11_EEPROM_ACCESS 0x0059 |
| #define CMD_802_11_BAND_CONFIG 0x0058 |
| #define CMD_802_11D_DOMAIN_INFO 0x005b |
| #define CMD_802_11_KEY_MATERIAL 0x005e |
| #define CMD_802_11_SLEEP_PARAMS 0x0066 |
| #define CMD_802_11_INACTIVITY_TIMEOUT 0x0067 |
| #define CMD_802_11_SLEEP_PERIOD 0x0068 |
| #define CMD_802_11_TPC_CFG 0x0072 |
| #define CMD_802_11_FW_WAKE_METHOD 0x0074 |
| #define CMD_802_11_SUBSCRIBE_EVENT 0x0075 |
| #define CMD_802_11_RATE_ADAPT_RATESET 0x0076 |
| #define CMD_802_11_TX_RATE_QUERY 0x007f |
| #define CMD_GET_TSF 0x0080 |
| #define CMD_BT_ACCESS 0x0087 |
| #define CMD_FWT_ACCESS 0x0095 |
| #define CMD_802_11_MONITOR_MODE 0x0098 |
| #define CMD_MESH_ACCESS 0x009b |
| #define CMD_MESH_CONFIG 0x00a3 |
| #define CMD_SET_BOOT2_VER 0x00a5 |
| #define CMD_802_11_BEACON_CTRL 0x00b0 |
| |
| /* For the IEEE Power Save */ |
| #define CMD_SUBCMD_ENTER_PS 0x0030 |
| #define CMD_SUBCMD_EXIT_PS 0x0031 |
| #define CMD_SUBCMD_SLEEP_CONFIRMED 0x0034 |
| #define CMD_SUBCMD_FULL_POWERDOWN 0x0035 |
| #define CMD_SUBCMD_FULL_POWERUP 0x0036 |
| |
| #define CMD_ENABLE_RSN 0x0001 |
| #define CMD_DISABLE_RSN 0x0000 |
| |
| #define CMD_ACT_GET 0x0000 |
| #define CMD_ACT_SET 0x0001 |
| #define CMD_ACT_GET_AES 0x0002 |
| #define CMD_ACT_SET_AES 0x0003 |
| #define CMD_ACT_REMOVE_AES 0x0004 |
| |
| /* Define action or option for CMD_802_11_SET_WEP */ |
| #define CMD_ACT_ADD 0x0002 |
| #define CMD_ACT_REMOVE 0x0004 |
| #define CMD_ACT_USE_DEFAULT 0x0008 |
| |
| #define CMD_TYPE_WEP_40_BIT 0x01 |
| #define CMD_TYPE_WEP_104_BIT 0x02 |
| |
| #define CMD_NUM_OF_WEP_KEYS 4 |
| |
| #define CMD_WEP_KEY_INDEX_MASK 0x3fff |
| |
| /* Define action or option for CMD_802_11_RESET */ |
| #define CMD_ACT_HALT 0x0003 |
| |
| /* Define action or option for CMD_802_11_SCAN */ |
| #define CMD_BSS_TYPE_BSS 0x0001 |
| #define CMD_BSS_TYPE_IBSS 0x0002 |
| #define CMD_BSS_TYPE_ANY 0x0003 |
| |
| /* Define action or option for CMD_802_11_SCAN */ |
| #define CMD_SCAN_TYPE_ACTIVE 0x0000 |
| #define CMD_SCAN_TYPE_PASSIVE 0x0001 |
| |
| #define CMD_SCAN_RADIO_TYPE_BG 0 |
| |
| #define CMD_SCAN_PROBE_DELAY_TIME 0 |
| |
| /* Define action or option for CMD_MAC_CONTROL */ |
| #define CMD_ACT_MAC_RX_ON 0x0001 |
| #define CMD_ACT_MAC_TX_ON 0x0002 |
| #define CMD_ACT_MAC_LOOPBACK_ON 0x0004 |
| #define CMD_ACT_MAC_WEP_ENABLE 0x0008 |
| #define CMD_ACT_MAC_INT_ENABLE 0x0010 |
| #define CMD_ACT_MAC_MULTICAST_ENABLE 0x0020 |
| #define CMD_ACT_MAC_BROADCAST_ENABLE 0x0040 |
| #define CMD_ACT_MAC_PROMISCUOUS_ENABLE 0x0080 |
| #define CMD_ACT_MAC_ALL_MULTICAST_ENABLE 0x0100 |
| #define CMD_ACT_MAC_STRICT_PROTECTION_ENABLE 0x0400 |
| |
| /* Define action or option for CMD_802_11_RADIO_CONTROL */ |
| #define CMD_TYPE_AUTO_PREAMBLE 0x0001 |
| #define CMD_TYPE_SHORT_PREAMBLE 0x0002 |
| #define CMD_TYPE_LONG_PREAMBLE 0x0003 |
| |
| /* Event flags for CMD_802_11_SUBSCRIBE_EVENT */ |
| #define CMD_SUBSCRIBE_RSSI_LOW 0x0001 |
| #define CMD_SUBSCRIBE_SNR_LOW 0x0002 |
| #define CMD_SUBSCRIBE_FAILCOUNT 0x0004 |
| #define CMD_SUBSCRIBE_BCNMISS 0x0008 |
| #define CMD_SUBSCRIBE_RSSI_HIGH 0x0010 |
| #define CMD_SUBSCRIBE_SNR_HIGH 0x0020 |
| |
| #define TURN_ON_RF 0x01 |
| #define RADIO_ON 0x01 |
| #define RADIO_OFF 0x00 |
| |
| #define SET_AUTO_PREAMBLE 0x05 |
| #define SET_SHORT_PREAMBLE 0x03 |
| #define SET_LONG_PREAMBLE 0x01 |
| |
| /* Define action or option for CMD_802_11_RF_CHANNEL */ |
| #define CMD_OPT_802_11_RF_CHANNEL_GET 0x00 |
| #define CMD_OPT_802_11_RF_CHANNEL_SET 0x01 |
| |
| /* Define action or option for CMD_802_11_RF_TX_POWER */ |
| #define CMD_ACT_TX_POWER_OPT_GET 0x0000 |
| #define CMD_ACT_TX_POWER_OPT_SET_HIGH 0x8007 |
| #define CMD_ACT_TX_POWER_OPT_SET_MID 0x8004 |
| #define CMD_ACT_TX_POWER_OPT_SET_LOW 0x8000 |
| |
| #define CMD_ACT_TX_POWER_INDEX_HIGH 0x0007 |
| #define CMD_ACT_TX_POWER_INDEX_MID 0x0004 |
| #define CMD_ACT_TX_POWER_INDEX_LOW 0x0000 |
| |
| /* Define action or option for CMD_802_11_DATA_RATE */ |
| #define CMD_ACT_SET_TX_AUTO 0x0000 |
| #define CMD_ACT_SET_TX_FIX_RATE 0x0001 |
| #define CMD_ACT_GET_TX_RATE 0x0002 |
| |
| #define CMD_ACT_SET_RX 0x0001 |
| #define CMD_ACT_SET_TX 0x0002 |
| #define CMD_ACT_SET_BOTH 0x0003 |
| #define CMD_ACT_GET_RX 0x0004 |
| #define CMD_ACT_GET_TX 0x0008 |
| #define CMD_ACT_GET_BOTH 0x000c |
| |
| /* Define action or option for CMD_802_11_PS_MODE */ |
| #define CMD_TYPE_CAM 0x0000 |
| #define CMD_TYPE_MAX_PSP 0x0001 |
| #define CMD_TYPE_FAST_PSP 0x0002 |
| |
| /* Options for CMD_802_11_FW_WAKE_METHOD */ |
| #define CMD_WAKE_METHOD_UNCHANGED 0x0000 |
| #define CMD_WAKE_METHOD_COMMAND_INT 0x0001 |
| #define CMD_WAKE_METHOD_GPIO 0x0002 |
| |
| /* Define action or option for CMD_BT_ACCESS */ |
| enum cmd_bt_access_opts { |
| /* The bt commands start at 5 instead of 1 because the old dft commands |
| * are mapped to 1-4. These old commands are no longer maintained and |
| * should not be called. |
| */ |
| CMD_ACT_BT_ACCESS_ADD = 5, |
| CMD_ACT_BT_ACCESS_DEL, |
| CMD_ACT_BT_ACCESS_LIST, |
| CMD_ACT_BT_ACCESS_RESET, |
| CMD_ACT_BT_ACCESS_SET_INVERT, |
| CMD_ACT_BT_ACCESS_GET_INVERT |
| }; |
| |
| /* Define action or option for CMD_FWT_ACCESS */ |
| enum cmd_fwt_access_opts { |
| CMD_ACT_FWT_ACCESS_ADD = 1, |
| CMD_ACT_FWT_ACCESS_DEL, |
| CMD_ACT_FWT_ACCESS_LOOKUP, |
| CMD_ACT_FWT_ACCESS_LIST, |
| CMD_ACT_FWT_ACCESS_LIST_ROUTE, |
| CMD_ACT_FWT_ACCESS_LIST_NEIGHBOR, |
| CMD_ACT_FWT_ACCESS_RESET, |
| CMD_ACT_FWT_ACCESS_CLEANUP, |
| CMD_ACT_FWT_ACCESS_TIME, |
| }; |
| |
| /* Define action or option for CMD_MESH_ACCESS */ |
| enum cmd_mesh_access_opts { |
| CMD_ACT_MESH_GET_TTL = 1, |
| CMD_ACT_MESH_SET_TTL, |
| CMD_ACT_MESH_GET_STATS, |
| CMD_ACT_MESH_GET_ANYCAST, |
| CMD_ACT_MESH_SET_ANYCAST, |
| CMD_ACT_MESH_SET_LINK_COSTS, |
| CMD_ACT_MESH_GET_LINK_COSTS, |
| CMD_ACT_MESH_SET_BCAST_RATE, |
| CMD_ACT_MESH_GET_BCAST_RATE, |
| CMD_ACT_MESH_SET_RREQ_DELAY, |
| CMD_ACT_MESH_GET_RREQ_DELAY, |
| CMD_ACT_MESH_SET_ROUTE_EXP, |
| CMD_ACT_MESH_GET_ROUTE_EXP, |
| CMD_ACT_MESH_SET_AUTOSTART_ENABLED, |
| CMD_ACT_MESH_GET_AUTOSTART_ENABLED, |
| }; |
| |
| /** Card Event definition */ |
| #define MACREG_INT_CODE_TX_PPA_FREE 0 |
| #define MACREG_INT_CODE_TX_DMA_DONE 1 |
| #define MACREG_INT_CODE_LINK_LOST_W_SCAN 2 |
| #define MACREG_INT_CODE_LINK_LOST_NO_SCAN 3 |
| #define MACREG_INT_CODE_LINK_SENSED 4 |
| #define MACREG_INT_CODE_CMD_FINISHED 5 |
| #define MACREG_INT_CODE_MIB_CHANGED 6 |
| #define MACREG_INT_CODE_INIT_DONE 7 |
| #define MACREG_INT_CODE_DEAUTHENTICATED 8 |
| #define MACREG_INT_CODE_DISASSOCIATED 9 |
| #define MACREG_INT_CODE_PS_AWAKE 10 |
| #define MACREG_INT_CODE_PS_SLEEP 11 |
| #define MACREG_INT_CODE_MIC_ERR_MULTICAST 13 |
| #define MACREG_INT_CODE_MIC_ERR_UNICAST 14 |
| #define MACREG_INT_CODE_WM_AWAKE 15 |
| #define MACREG_INT_CODE_DEEP_SLEEP_AWAKE 16 |
| #define MACREG_INT_CODE_ADHOC_BCN_LOST 17 |
| #define MACREG_INT_CODE_HOST_AWAKE 18 |
| #define MACREG_INT_CODE_STOP_TX 19 |
| #define MACREG_INT_CODE_START_TX 20 |
| #define MACREG_INT_CODE_CHANNEL_SWITCH 21 |
| #define MACREG_INT_CODE_MEASUREMENT_RDY 22 |
| #define MACREG_INT_CODE_WMM_CHANGE 23 |
| #define MACREG_INT_CODE_BG_SCAN_REPORT 24 |
| #define MACREG_INT_CODE_RSSI_LOW 25 |
| #define MACREG_INT_CODE_SNR_LOW 26 |
| #define MACREG_INT_CODE_MAX_FAIL 27 |
| #define MACREG_INT_CODE_RSSI_HIGH 28 |
| #define MACREG_INT_CODE_SNR_HIGH 29 |
| #define MACREG_INT_CODE_MESH_AUTO_STARTED 35 |
| #define MACREG_INT_CODE_FIRMWARE_READY 48 |
| |
| #endif |