Merge branch 'depends/i2c/lpc32xx' into next/dt
As a prerequisite for merging the lpc32xx DT changes, this
pulls in the depends/i2c/lpc32xx branch that contains
changes to the pnx-i2c driver, which are already in the
i2c tree. The branch is available also on
git://git.antcom.de/linux-2.6.git lpc32xx/i2c
Roland Stigge <stigge@antcom.de> writes:
this is the series of the 4 patches adding device tree support to i2c-pnx
(used by LPC32xx) that Wolfram Sang already applied to the i2c subsystem.
Since both drivers/i2c/ and mach-lpc32xx are touched here, there will
probably be conflicts that you need to be aware of.
I'm posting this again for arm-soc since the actual mach-lpc32xx specific
DT conversion builds upon those changes (see next pull request), especially
in arch/arm/mach-lpc32xx/common.c.
Wolfram already gave permission to merge this via arm-soc, but please
coordinate and tell me if I can help resolving this.
Further, this implicitly updates the next/dt branch to v3.4-rc4, which
causes a trivial conflict from a change in one branch in code that
gets removed in another.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[olof: rebuilt branch due to drop of an early merge]
Signed-off-by: Olof Johansson <olof@lixom.net>
diff --git a/Documentation/arm/SPEAr/overview.txt b/Documentation/arm/SPEAr/overview.txt
index 253a35c..28a9af9 100644
--- a/Documentation/arm/SPEAr/overview.txt
+++ b/Documentation/arm/SPEAr/overview.txt
@@ -17,14 +17,14 @@
SPEAr (Platform)
- SPEAr3XX (3XX SOC series, based on ARM9)
- SPEAr300 (SOC)
- - SPEAr300_EVB (Evaluation Board)
+ - SPEAr300 Evaluation Board
- SPEAr310 (SOC)
- - SPEAr310_EVB (Evaluation Board)
+ - SPEAr310 Evaluation Board
- SPEAr320 (SOC)
- - SPEAr320_EVB (Evaluation Board)
+ - SPEAr320 Evaluation Board
- SPEAr6XX (6XX SOC series, based on ARM9)
- SPEAr600 (SOC)
- - SPEAr600_EVB (Evaluation Board)
+ - SPEAr600 Evaluation Board
- SPEAr13XX (13XX SOC series, based on ARM CORTEXA9)
- SPEAr1300 (SOC)
@@ -51,10 +51,11 @@
Common file for machines of spear3xx family is mach-spear3xx/spear3xx.c and for
spear6xx is mach-spear6xx/spear6xx.c. mach-spear* also contain soc/machine
specific files, like spear300.c, spear310.c, spear320.c and spear600.c.
- mach-spear* also contains board specific files for each machine type.
+ mach-spear* doesn't contains board specific files as they fully support
+ Flattened Device Tree.
Document Author
---------------
- Viresh Kumar, (c) 2010 ST Microelectronics
+ Viresh Kumar <viresh.kumar@st.com>, (c) 2010-2012 ST Microelectronics
diff --git a/Documentation/devicetree/bindings/arm/spear.txt b/Documentation/devicetree/bindings/arm/spear.txt
index f8e54f0..aa5f355 100644
--- a/Documentation/devicetree/bindings/arm/spear.txt
+++ b/Documentation/devicetree/bindings/arm/spear.txt
@@ -6,3 +6,21 @@
Required root node property:
compatible = "st,spear600";
+
+Boards with the ST SPEAr300 SoC shall have the following properties:
+
+Required root node property:
+
+compatible = "st,spear300";
+
+Boards with the ST SPEAr310 SoC shall have the following properties:
+
+Required root node property:
+
+compatible = "st,spear310";
+
+Boards with the ST SPEAr320 SoC shall have the following properties:
+
+Required root node property:
+
+compatible = "st,spear320";
diff --git a/arch/arm/boot/dts/omap3-beagle.dts b/arch/arm/boot/dts/omap3-beagle.dts
index 9f72cd4..8c756be 100644
--- a/arch/arm/boot/dts/omap3-beagle.dts
+++ b/arch/arm/boot/dts/omap3-beagle.dts
@@ -18,3 +18,52 @@
reg = <0x80000000 0x20000000>; /* 512 MB */
};
};
+
+&i2c1 {
+ clock-frequency = <2600000>;
+
+ twl: twl@48 {
+ reg = <0x48>;
+ interrupts = <7>; /* SYS_NIRQ cascaded to intc */
+ interrupt-parent = <&intc>;
+
+ vsim: regulator@10 {
+ compatible = "ti,twl4030-vsim";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3000000>;
+ };
+ };
+};
+
+/include/ "twl4030.dtsi"
+
+&i2c2 {
+ clock-frequency = <400000>;
+};
+
+&i2c3 {
+ clock-frequency = <100000>;
+
+ /*
+ * Display monitor features are burnt in the EEPROM
+ * as EDID data.
+ */
+ eeprom@50 {
+ compatible = "ti,eeprom";
+ reg = <0x50>;
+ };
+};
+
+&mmc1 {
+ vmmc-supply = <&vmmc1>;
+ vmmc_aux-supply = <&vsim>;
+ ti,bus-width = <8>;
+};
+
+&mmc2 {
+ status = "disable";
+};
+
+&mmc3 {
+ status = "disable";
+};
diff --git a/arch/arm/boot/dts/omap3.dtsi b/arch/arm/boot/dts/omap3.dtsi
index c612135..99474fa 100644
--- a/arch/arm/boot/dts/omap3.dtsi
+++ b/arch/arm/boot/dts/omap3.dtsi
@@ -69,6 +69,60 @@
reg = <0x48200000 0x1000>;
};
+ gpio1: gpio@48310000 {
+ compatible = "ti,omap3-gpio";
+ ti,hwmods = "gpio1";
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+
+ gpio2: gpio@49050000 {
+ compatible = "ti,omap3-gpio";
+ ti,hwmods = "gpio2";
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+
+ gpio3: gpio@49052000 {
+ compatible = "ti,omap3-gpio";
+ ti,hwmods = "gpio3";
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+
+ gpio4: gpio@49054000 {
+ compatible = "ti,omap3-gpio";
+ ti,hwmods = "gpio4";
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+
+ gpio5: gpio@49056000 {
+ compatible = "ti,omap3-gpio";
+ ti,hwmods = "gpio5";
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+
+ gpio6: gpio@49058000 {
+ compatible = "ti,omap3-gpio";
+ ti,hwmods = "gpio6";
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+
uart1: serial@4806a000 {
compatible = "ti,omap3-uart";
ti,hwmods = "uart1";
@@ -113,5 +167,53 @@
#size-cells = <0>;
ti,hwmods = "i2c3";
};
+
+ mcspi1: spi@48098000 {
+ compatible = "ti,omap2-mcspi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ ti,hwmods = "mcspi1";
+ ti,spi-num-cs = <4>;
+ };
+
+ mcspi2: spi@4809a000 {
+ compatible = "ti,omap2-mcspi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ ti,hwmods = "mcspi2";
+ ti,spi-num-cs = <2>;
+ };
+
+ mcspi3: spi@480b8000 {
+ compatible = "ti,omap2-mcspi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ ti,hwmods = "mcspi3";
+ ti,spi-num-cs = <2>;
+ };
+
+ mcspi4: spi@480ba000 {
+ compatible = "ti,omap2-mcspi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ ti,hwmods = "mcspi4";
+ ti,spi-num-cs = <1>;
+ };
+
+ mmc1: mmc@4809c000 {
+ compatible = "ti,omap3-hsmmc";
+ ti,hwmods = "mmc1";
+ ti,dual-volt;
+ };
+
+ mmc2: mmc@480b4000 {
+ compatible = "ti,omap3-hsmmc";
+ ti,hwmods = "mmc2";
+ };
+
+ mmc3: mmc@480ad000 {
+ compatible = "ti,omap3-hsmmc";
+ ti,hwmods = "mmc3";
+ };
};
};
diff --git a/arch/arm/boot/dts/omap4-panda.dts b/arch/arm/boot/dts/omap4-panda.dts
index 9755ad5..ea6f5bb 100644
--- a/arch/arm/boot/dts/omap4-panda.dts
+++ b/arch/arm/boot/dts/omap4-panda.dts
@@ -18,3 +18,59 @@
reg = <0x80000000 0x40000000>; /* 1 GB */
};
};
+
+&i2c1 {
+ clock-frequency = <400000>;
+
+ twl: twl@48 {
+ reg = <0x48>;
+ /* SPI = 0, IRQ# = 7, 4 = active high level-sensitive */
+ interrupts = <0 7 4>; /* IRQ_SYS_1N cascaded to gic */
+ interrupt-parent = <&gic>;
+ };
+};
+
+/include/ "twl6030.dtsi"
+
+&i2c2 {
+ clock-frequency = <400000>;
+};
+
+&i2c3 {
+ clock-frequency = <100000>;
+
+ /*
+ * Display monitor features are burnt in their EEPROM as EDID data.
+ * The EEPROM is connected as I2C slave device.
+ */
+ eeprom@50 {
+ compatible = "ti,eeprom";
+ reg = <0x50>;
+ };
+};
+
+&i2c4 {
+ clock-frequency = <400000>;
+};
+
+&mmc1 {
+ vmmc-supply = <&vmmc>;
+ ti,bus-width = <8>;
+};
+
+&mmc2 {
+ status = "disable";
+};
+
+&mmc3 {
+ status = "disable";
+};
+
+&mmc4 {
+ status = "disable";
+};
+
+&mmc5 {
+ ti,non-removable;
+ ti,bus-width = <4>;
+};
diff --git a/arch/arm/boot/dts/omap4-sdp.dts b/arch/arm/boot/dts/omap4-sdp.dts
index 63c6b2b..67b2e98 100644
--- a/arch/arm/boot/dts/omap4-sdp.dts
+++ b/arch/arm/boot/dts/omap4-sdp.dts
@@ -17,4 +17,101 @@
device_type = "memory";
reg = <0x80000000 0x40000000>; /* 1 GB */
};
+
+ vdd_eth: fixedregulator@0 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDD_ETH";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio2 16 0>; /* gpio line 48 */
+ enable-active-high;
+ regulator-boot-on;
+ };
+};
+
+&i2c1 {
+ clock-frequency = <400000>;
+
+ twl: twl@48 {
+ reg = <0x48>;
+ /* SPI = 0, IRQ# = 7, 4 = active high level-sensitive */
+ interrupts = <0 7 4>; /* IRQ_SYS_1N cascaded to gic */
+ interrupt-parent = <&gic>;
+ };
+};
+
+/include/ "twl6030.dtsi"
+
+&i2c2 {
+ clock-frequency = <400000>;
+};
+
+&i2c3 {
+ clock-frequency = <400000>;
+
+ /*
+ * Temperature Sensor
+ * http://www.ti.com/lit/ds/symlink/tmp105.pdf
+ */
+ tmp105@48 {
+ compatible = "ti,tmp105";
+ reg = <0x48>;
+ };
+
+ /*
+ * Ambient Light Sensor
+ * http://www.rohm.com/products/databook/sensor/pdf/bh1780gli-e.pdf
+ */
+ bh1780@29 {
+ compatible = "rohm,bh1780";
+ reg = <0x29>;
+ };
+};
+
+&i2c4 {
+ clock-frequency = <400000>;
+
+ /*
+ * 3-Axis Digital Compass
+ * http://www.sparkfun.com/datasheets/Sensors/Magneto/HMC5843.pdf
+ */
+ hmc5843@1e {
+ compatible = "honeywell,hmc5843";
+ reg = <0x1e>;
+ };
+};
+
+&mcspi1 {
+ eth@0 {
+ compatible = "ks8851";
+ spi-max-frequency = <24000000>;
+ reg = <0>;
+ interrupt-parent = <&gpio2>;
+ interrupts = <2>; /* gpio line 34 */
+ vdd-supply = <&vdd_eth>;
+ };
+};
+
+&mmc1 {
+ vmmc-supply = <&vmmc>;
+ ti,bus-width = <8>;
+};
+
+&mmc2 {
+ vmmc-supply = <&vaux1>;
+ ti,bus-width = <8>;
+ ti,non-removable;
+};
+
+&mmc3 {
+ status = "disable";
+};
+
+&mmc4 {
+ status = "disable";
+};
+
+&mmc5 {
+ ti,bus-width = <4>;
+ ti,non-removable;
};
diff --git a/arch/arm/boot/dts/omap4.dtsi b/arch/arm/boot/dts/omap4.dtsi
index 3d35559..359c497 100644
--- a/arch/arm/boot/dts/omap4.dtsi
+++ b/arch/arm/boot/dts/omap4.dtsi
@@ -104,6 +104,60 @@
<0x48240100 0x0100>;
};
+ gpio1: gpio@4a310000 {
+ compatible = "ti,omap4-gpio";
+ ti,hwmods = "gpio1";
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+
+ gpio2: gpio@48055000 {
+ compatible = "ti,omap4-gpio";
+ ti,hwmods = "gpio2";
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+
+ gpio3: gpio@48057000 {
+ compatible = "ti,omap4-gpio";
+ ti,hwmods = "gpio3";
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+
+ gpio4: gpio@48059000 {
+ compatible = "ti,omap4-gpio";
+ ti,hwmods = "gpio4";
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+
+ gpio5: gpio@4805b000 {
+ compatible = "ti,omap4-gpio";
+ ti,hwmods = "gpio5";
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+
+ gpio6: gpio@4805d000 {
+ compatible = "ti,omap4-gpio";
+ ti,hwmods = "gpio6";
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+
uart1: serial@4806a000 {
compatible = "ti,omap4-uart";
ti,hwmods = "uart1";
@@ -155,5 +209,68 @@
#size-cells = <0>;
ti,hwmods = "i2c4";
};
+
+ mcspi1: spi@48098000 {
+ compatible = "ti,omap4-mcspi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ ti,hwmods = "mcspi1";
+ ti,spi-num-cs = <4>;
+ };
+
+ mcspi2: spi@4809a000 {
+ compatible = "ti,omap4-mcspi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ ti,hwmods = "mcspi2";
+ ti,spi-num-cs = <2>;
+ };
+
+ mcspi3: spi@480b8000 {
+ compatible = "ti,omap4-mcspi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ ti,hwmods = "mcspi3";
+ ti,spi-num-cs = <2>;
+ };
+
+ mcspi4: spi@480ba000 {
+ compatible = "ti,omap4-mcspi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ ti,hwmods = "mcspi4";
+ ti,spi-num-cs = <1>;
+ };
+
+ mmc1: mmc@4809c000 {
+ compatible = "ti,omap4-hsmmc";
+ ti,hwmods = "mmc1";
+ ti,dual-volt;
+ ti,needs-special-reset;
+ };
+
+ mmc2: mmc@480b4000 {
+ compatible = "ti,omap4-hsmmc";
+ ti,hwmods = "mmc2";
+ ti,needs-special-reset;
+ };
+
+ mmc3: mmc@480ad000 {
+ compatible = "ti,omap4-hsmmc";
+ ti,hwmods = "mmc3";
+ ti,needs-special-reset;
+ };
+
+ mmc4: mmc@480d1000 {
+ compatible = "ti,omap4-hsmmc";
+ ti,hwmods = "mmc4";
+ ti,needs-special-reset;
+ };
+
+ mmc5: mmc@480d5000 {
+ compatible = "ti,omap4-hsmmc";
+ ti,hwmods = "mmc5";
+ ti,needs-special-reset;
+ };
};
};
diff --git a/arch/arm/boot/dts/sh7372.dtsi b/arch/arm/boot/dts/sh7372.dtsi
new file mode 100644
index 0000000..677fc60
--- /dev/null
+++ b/arch/arm/boot/dts/sh7372.dtsi
@@ -0,0 +1,21 @@
+/*
+ * Device Tree Source for the sh7372 SoC
+ *
+ * Copyright (C) 2012 Renesas Solutions Corp.
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+/include/ "skeleton.dtsi"
+
+/ {
+ compatible = "renesas,sh7372";
+
+ cpus {
+ cpu@0 {
+ compatible = "arm,cortex-a8";
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/spear300-evb.dts b/arch/arm/boot/dts/spear300-evb.dts
new file mode 100644
index 0000000..eaecc29
--- /dev/null
+++ b/arch/arm/boot/dts/spear300-evb.dts
@@ -0,0 +1,183 @@
+/*
+ * DTS file for SPEAr300 Evaluation Baord
+ *
+ * Copyright 2012 Viresh Kumar <viresh.kumar@st.com>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+/include/ "spear300.dtsi"
+
+/ {
+ model = "ST SPEAr300 Evaluation Board";
+ compatible = "st,spear300-evb", "st,spear300";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ memory {
+ reg = <0 0x40000000>;
+ };
+
+ ahb {
+ clcd@60000000 {
+ status = "okay";
+ };
+
+ dma@fc400000 {
+ status = "okay";
+ };
+
+ fsmc: flash@94000000 {
+ status = "okay";
+ };
+
+ gmac: eth@e0800000 {
+ status = "okay";
+ };
+
+ sdhci@70000000 {
+ int-gpio = <&gpio1 0 0>;
+ power-gpio = <&gpio1 2 1>;
+ status = "okay";
+ };
+
+ smi: flash@fc000000 {
+ status = "okay";
+ };
+
+ spi0: spi@d0100000 {
+ status = "okay";
+ };
+
+ ehci@e1800000 {
+ status = "okay";
+ };
+
+ ohci@e1900000 {
+ status = "okay";
+ };
+
+ ohci@e2100000 {
+ status = "okay";
+ };
+
+ apb {
+ gpio0: gpio@fc980000 {
+ status = "okay";
+ };
+
+ gpio1: gpio@a9000000 {
+ status = "okay";
+ };
+
+ i2c0: i2c@d0180000 {
+ status = "okay";
+ };
+
+ kbd@a0000000 {
+ linux,keymap = < 0x00010000
+ 0x00020100
+ 0x00030200
+ 0x00040300
+ 0x00050400
+ 0x00060500
+ 0x00070600
+ 0x00080700
+ 0x00090800
+ 0x000a0001
+ 0x000c0101
+ 0x000d0201
+ 0x000e0301
+ 0x000f0401
+ 0x00100501
+ 0x00110601
+ 0x00120701
+ 0x00130801
+ 0x00140002
+ 0x00150102
+ 0x00160202
+ 0x00170302
+ 0x00180402
+ 0x00190502
+ 0x001a0602
+ 0x001b0702
+ 0x001c0802
+ 0x001d0003
+ 0x001e0103
+ 0x001f0203
+ 0x00200303
+ 0x00210403
+ 0x00220503
+ 0x00230603
+ 0x00240703
+ 0x00250803
+ 0x00260004
+ 0x00270104
+ 0x00280204
+ 0x00290304
+ 0x002a0404
+ 0x002b0504
+ 0x002c0604
+ 0x002d0704
+ 0x002e0804
+ 0x002f0005
+ 0x00300105
+ 0x00310205
+ 0x00320305
+ 0x00330405
+ 0x00340505
+ 0x00350605
+ 0x00360705
+ 0x00370805
+ 0x00380006
+ 0x00390106
+ 0x003a0206
+ 0x003b0306
+ 0x003c0406
+ 0x003d0506
+ 0x003e0606
+ 0x003f0706
+ 0x00400806
+ 0x00410007
+ 0x00420107
+ 0x00430207
+ 0x00440307
+ 0x00450407
+ 0x00460507
+ 0x00470607
+ 0x00480707
+ 0x00490807
+ 0x004a0008
+ 0x004b0108
+ 0x004c0208
+ 0x004d0308
+ 0x004e0408
+ 0x004f0508
+ 0x00500608
+ 0x00510708
+ 0x00520808 >;
+ autorepeat;
+ st,mode = <0>;
+ status = "okay";
+ };
+
+ rtc@fc900000 {
+ status = "okay";
+ };
+
+ serial@d0000000 {
+ status = "okay";
+ };
+
+ wdt@fc880000 {
+ status = "okay";
+ };
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/spear300.dtsi b/arch/arm/boot/dts/spear300.dtsi
new file mode 100644
index 0000000..f9fcbf4
--- /dev/null
+++ b/arch/arm/boot/dts/spear300.dtsi
@@ -0,0 +1,72 @@
+/*
+ * DTS file for SPEAr300 SoC
+ *
+ * Copyright 2012 Viresh Kumar <viresh.kumar@st.com>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/include/ "spear3xx.dtsi"
+
+/ {
+ ahb {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "simple-bus";
+ ranges = <0x60000000 0x60000000 0x50000000
+ 0xd0000000 0xd0000000 0x30000000>;
+
+ clcd@60000000 {
+ compatible = "arm,clcd-pl110", "arm,primecell";
+ reg = <0x60000000 0x1000>;
+ interrupts = <30>;
+ status = "disabled";
+ };
+
+ fsmc: flash@94000000 {
+ compatible = "st,spear600-fsmc-nand";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x94000000 0x1000 /* FSMC Register */
+ 0x80000000 0x0010>; /* NAND Base */
+ reg-names = "fsmc_regs", "nand_data";
+ st,ale-off = <0x20000>;
+ st,cle-off = <0x10000>;
+ status = "disabled";
+ };
+
+ sdhci@70000000 {
+ compatible = "st,sdhci-spear";
+ reg = <0x70000000 0x100>;
+ interrupts = <1>;
+ status = "disabled";
+ };
+
+ apb {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "simple-bus";
+ ranges = <0xa0000000 0xa0000000 0x10000000
+ 0xd0000000 0xd0000000 0x30000000>;
+
+ gpio1: gpio@a9000000 {
+ #gpio-cells = <2>;
+ compatible = "arm,pl061", "arm,primecell";
+ gpio-controller;
+ reg = <0xa9000000 0x1000>;
+ status = "disabled";
+ };
+
+ kbd@a0000000 {
+ compatible = "st,spear300-kbd";
+ reg = <0xa0000000 0x1000>;
+ status = "disabled";
+ };
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/spear310-evb.dts b/arch/arm/boot/dts/spear310-evb.dts
new file mode 100644
index 0000000..c86af33
--- /dev/null
+++ b/arch/arm/boot/dts/spear310-evb.dts
@@ -0,0 +1,111 @@
+/*
+ * DTS file for SPEAr310 Evaluation Baord
+ *
+ * Copyright 2012 Viresh Kumar <viresh.kumar@st.com>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+/include/ "spear310.dtsi"
+
+/ {
+ model = "ST SPEAr310 Evaluation Board";
+ compatible = "st,spear310-evb", "st,spear310";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ memory {
+ reg = <0 0x40000000>;
+ };
+
+ ahb {
+ dma@fc400000 {
+ status = "okay";
+ };
+
+ fsmc: flash@44000000 {
+ status = "okay";
+ };
+
+ gmac: eth@e0800000 {
+ status = "okay";
+ };
+
+ smi: flash@fc000000 {
+ status = "okay";
+ clock-rate=<50000000>;
+
+ flash@f8000000 {
+ label = "m25p64";
+ reg = <0xf8000000 0x800000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ st,smi-fast-mode;
+ };
+ };
+
+ spi0: spi@d0100000 {
+ status = "okay";
+ };
+
+ ehci@e1800000 {
+ status = "okay";
+ };
+
+ ohci@e1900000 {
+ status = "okay";
+ };
+
+ ohci@e2100000 {
+ status = "okay";
+ };
+
+ apb {
+ gpio0: gpio@fc980000 {
+ status = "okay";
+ };
+
+ i2c0: i2c@d0180000 {
+ status = "okay";
+ };
+
+ rtc@fc900000 {
+ status = "okay";
+ };
+
+ serial@d0000000 {
+ status = "okay";
+ };
+
+ serial@b2000000 {
+ status = "okay";
+ };
+
+ serial@b2080000 {
+ status = "okay";
+ };
+
+ serial@b2100000 {
+ status = "okay";
+ };
+
+ serial@b2180000 {
+ status = "okay";
+ };
+
+ serial@b2200000 {
+ status = "okay";
+ };
+
+ wdt@fc880000 {
+ status = "okay";
+ };
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/spear310.dtsi b/arch/arm/boot/dts/spear310.dtsi
new file mode 100644
index 0000000..dc7fa14
--- /dev/null
+++ b/arch/arm/boot/dts/spear310.dtsi
@@ -0,0 +1,75 @@
+/*
+ * DTS file for SPEAr310 SoC
+ *
+ * Copyright 2012 Viresh Kumar <viresh.kumar@st.com>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/include/ "spear3xx.dtsi"
+
+/ {
+ ahb {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "simple-bus";
+ ranges = <0x40000000 0x40000000 0x10000000
+ 0xb0000000 0xb0000000 0x10000000
+ 0xd0000000 0xd0000000 0x30000000>;
+
+ fsmc: flash@44000000 {
+ compatible = "st,spear600-fsmc-nand";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x44000000 0x1000 /* FSMC Register */
+ 0x40000000 0x0010>; /* NAND Base */
+ reg-names = "fsmc_regs", "nand_data";
+ st,ale-off = <0x10000>;
+ st,cle-off = <0x20000>;
+ status = "disabled";
+ };
+
+ apb {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "simple-bus";
+ ranges = <0xb0000000 0xb0000000 0x10000000
+ 0xd0000000 0xd0000000 0x30000000>;
+
+ serial@b2000000 {
+ compatible = "arm,pl011", "arm,primecell";
+ reg = <0xb2000000 0x1000>;
+ status = "disabled";
+ };
+
+ serial@b2080000 {
+ compatible = "arm,pl011", "arm,primecell";
+ reg = <0xb2080000 0x1000>;
+ status = "disabled";
+ };
+
+ serial@b2100000 {
+ compatible = "arm,pl011", "arm,primecell";
+ reg = <0xb2100000 0x1000>;
+ status = "disabled";
+ };
+
+ serial@b2180000 {
+ compatible = "arm,pl011", "arm,primecell";
+ reg = <0xb2180000 0x1000>;
+ status = "disabled";
+ };
+
+ serial@b2200000 {
+ compatible = "arm,pl011", "arm,primecell";
+ reg = <0xb2200000 0x1000>;
+ status = "disabled";
+ };
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/spear320-evb.dts b/arch/arm/boot/dts/spear320-evb.dts
new file mode 100644
index 0000000..d43de71
--- /dev/null
+++ b/arch/arm/boot/dts/spear320-evb.dts
@@ -0,0 +1,112 @@
+/*
+ * DTS file for SPEAr320 Evaluation Baord
+ *
+ * Copyright 2012 Viresh Kumar <viresh.kumar@st.com>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+/include/ "spear320.dtsi"
+
+/ {
+ model = "ST SPEAr300 Evaluation Board";
+ compatible = "st,spear300-evb", "st,spear300";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ memory {
+ reg = <0 0x40000000>;
+ };
+
+ ahb {
+ clcd@90000000 {
+ status = "okay";
+ };
+
+ dma@fc400000 {
+ status = "okay";
+ };
+
+ fsmc: flash@4c000000 {
+ status = "okay";
+ };
+
+ gmac: eth@e0800000 {
+ status = "okay";
+ };
+
+ sdhci@70000000 {
+ power-gpio = <&gpio0 2 1>;
+ power_always_enb;
+ status = "okay";
+ };
+
+ smi: flash@fc000000 {
+ status = "okay";
+ };
+
+ spi0: spi@d0100000 {
+ status = "okay";
+ };
+
+ spi1: spi@a5000000 {
+ status = "okay";
+ };
+
+ spi2: spi@a6000000 {
+ status = "okay";
+ };
+
+ ehci@e1800000 {
+ status = "okay";
+ };
+
+ ohci@e1900000 {
+ status = "okay";
+ };
+
+ ohci@e2100000 {
+ status = "okay";
+ };
+
+ apb {
+ gpio0: gpio@fc980000 {
+ status = "okay";
+ };
+
+ i2c0: i2c@d0180000 {
+ status = "okay";
+ };
+
+ i2c1: i2c@a7000000 {
+ status = "okay";
+ };
+
+ rtc@fc900000 {
+ status = "okay";
+ };
+
+ serial@d0000000 {
+ status = "okay";
+ };
+
+ serial@a3000000 {
+ status = "okay";
+ };
+
+ serial@a4000000 {
+ status = "okay";
+ };
+
+ wdt@fc880000 {
+ status = "okay";
+ };
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/spear320.dtsi b/arch/arm/boot/dts/spear320.dtsi
new file mode 100644
index 0000000..9a0267a
--- /dev/null
+++ b/arch/arm/boot/dts/spear320.dtsi
@@ -0,0 +1,90 @@
+/*
+ * DTS file for SPEAr320 SoC
+ *
+ * Copyright 2012 Viresh Kumar <viresh.kumar@st.com>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/include/ "spear3xx.dtsi"
+
+/ {
+ ahb {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "simple-bus";
+ ranges = <0x40000000 0x40000000 0x70000000
+ 0xd0000000 0xd0000000 0x30000000>;
+
+ clcd@90000000 {
+ compatible = "arm,clcd-pl110", "arm,primecell";
+ reg = <0x90000000 0x1000>;
+ interrupts = <33>;
+ status = "disabled";
+ };
+
+ fsmc: flash@4c000000 {
+ compatible = "st,spear600-fsmc-nand";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x4c000000 0x1000 /* FSMC Register */
+ 0x50000000 0x0010>; /* NAND Base */
+ reg-names = "fsmc_regs", "nand_data";
+ st,ale-off = <0x20000>;
+ st,cle-off = <0x10000>;
+ status = "disabled";
+ };
+
+ sdhci@70000000 {
+ compatible = "st,sdhci-spear";
+ reg = <0x70000000 0x100>;
+ interrupts = <29>;
+ status = "disabled";
+ };
+
+ spi1: spi@a5000000 {
+ compatible = "arm,pl022", "arm,primecell";
+ reg = <0xa5000000 0x1000>;
+ status = "disabled";
+ };
+
+ spi2: spi@a6000000 {
+ compatible = "arm,pl022", "arm,primecell";
+ reg = <0xa6000000 0x1000>;
+ status = "disabled";
+ };
+
+ apb {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "simple-bus";
+ ranges = <0xa0000000 0xa0000000 0x10000000
+ 0xd0000000 0xd0000000 0x30000000>;
+
+ i2c1: i2c@a7000000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "snps,designware-i2c";
+ reg = <0xa7000000 0x1000>;
+ status = "disabled";
+ };
+
+ serial@a3000000 {
+ compatible = "arm,pl011", "arm,primecell";
+ reg = <0xa3000000 0x1000>;
+ status = "disabled";
+ };
+
+ serial@a4000000 {
+ compatible = "arm,pl011", "arm,primecell";
+ reg = <0xa4000000 0x1000>;
+ status = "disabled";
+ };
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/spear3xx.dtsi b/arch/arm/boot/dts/spear3xx.dtsi
new file mode 100644
index 0000000..0ae7c8e
--- /dev/null
+++ b/arch/arm/boot/dts/spear3xx.dtsi
@@ -0,0 +1,144 @@
+/*
+ * DTS file for all SPEAr3xx SoCs
+ *
+ * Copyright 2012 Viresh Kumar <viresh.kumar@st.com>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/include/ "skeleton.dtsi"
+
+/ {
+ interrupt-parent = <&vic>;
+
+ cpus {
+ cpu@0 {
+ compatible = "arm,arm926ejs";
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0 0x40000000>;
+ };
+
+ ahb {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "simple-bus";
+ ranges = <0xd0000000 0xd0000000 0x30000000>;
+
+ vic: interrupt-controller@f1100000 {
+ compatible = "arm,pl190-vic";
+ interrupt-controller;
+ reg = <0xf1100000 0x1000>;
+ #interrupt-cells = <1>;
+ };
+
+ dma@fc400000 {
+ compatible = "arm,pl080", "arm,primecell";
+ reg = <0xfc400000 0x1000>;
+ interrupt-parent = <&vic>;
+ interrupts = <8>;
+ status = "disabled";
+ };
+
+ gmac: eth@e0800000 {
+ compatible = "st,spear600-gmac";
+ reg = <0xe0800000 0x8000>;
+ interrupts = <23 22>;
+ interrupt-names = "macirq", "eth_wake_irq";
+ status = "disabled";
+ };
+
+ smi: flash@fc000000 {
+ compatible = "st,spear600-smi";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0xfc000000 0x1000>;
+ interrupts = <9>;
+ status = "disabled";
+ };
+
+ spi0: spi@d0100000 {
+ compatible = "arm,pl022", "arm,primecell";
+ reg = <0xd0100000 0x1000>;
+ interrupts = <20>;
+ status = "disabled";
+ };
+
+ ehci@e1800000 {
+ compatible = "st,spear600-ehci", "usb-ehci";
+ reg = <0xe1800000 0x1000>;
+ interrupts = <26>;
+ status = "disabled";
+ };
+
+ ohci@e1900000 {
+ compatible = "st,spear600-ohci", "usb-ohci";
+ reg = <0xe1900000 0x1000>;
+ interrupts = <25>;
+ status = "disabled";
+ };
+
+ ohci@e2100000 {
+ compatible = "st,spear600-ohci", "usb-ohci";
+ reg = <0xe2100000 0x1000>;
+ interrupts = <27>;
+ status = "disabled";
+ };
+
+ apb {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "simple-bus";
+ ranges = <0xd0000000 0xd0000000 0x30000000>;
+
+ gpio0: gpio@fc980000 {
+ compatible = "arm,pl061", "arm,primecell";
+ reg = <0xfc980000 0x1000>;
+ interrupts = <11>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ status = "disabled";
+ };
+
+ i2c0: i2c@d0180000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "snps,designware-i2c";
+ reg = <0xd0180000 0x1000>;
+ interrupts = <21>;
+ status = "disabled";
+ };
+
+ rtc@fc900000 {
+ compatible = "st,spear-rtc";
+ reg = <0xfc900000 0x1000>;
+ interrupts = <10>;
+ status = "disabled";
+ };
+
+ serial@d0000000 {
+ compatible = "arm,pl011", "arm,primecell";
+ reg = <0xd0000000 0x1000>;
+ interrupts = <19>;
+ status = "disabled";
+ };
+
+ wdt@fc880000 {
+ compatible = "arm,sp805", "arm,primecell";
+ reg = <0xfc880000 0x1000>;
+ interrupts = <12>;
+ status = "disabled";
+ };
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/spear600-evb.dts b/arch/arm/boot/dts/spear600-evb.dts
index 636292e..790a7a8 100644
--- a/arch/arm/boot/dts/spear600-evb.dts
+++ b/arch/arm/boot/dts/spear600-evb.dts
@@ -24,6 +24,10 @@
};
ahb {
+ dma@fc400000 {
+ status = "okay";
+ };
+
gmac: ethernet@e0800000 {
phy-mode = "gmii";
status = "okay";
diff --git a/arch/arm/boot/dts/spear600.dtsi b/arch/arm/boot/dts/spear600.dtsi
index ebe0885..d777e3a 100644
--- a/arch/arm/boot/dts/spear600.dtsi
+++ b/arch/arm/boot/dts/spear600.dtsi
@@ -45,6 +45,14 @@
#interrupt-cells = <1>;
};
+ dma@fc400000 {
+ compatible = "arm,pl080", "arm,primecell";
+ reg = <0xfc400000 0x1000>;
+ interrupt-parent = <&vic1>;
+ interrupts = <10>;
+ status = "disabled";
+ };
+
gmac: ethernet@e0800000 {
compatible = "st,spear600-gmac";
reg = <0xe0800000 0x8000>;
diff --git a/arch/arm/boot/dts/twl4030.dtsi b/arch/arm/boot/dts/twl4030.dtsi
new file mode 100644
index 0000000..a94654c
--- /dev/null
+++ b/arch/arm/boot/dts/twl4030.dtsi
@@ -0,0 +1,39 @@
+/*
+ * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/*
+ * Integrated Power Management Chip
+ */
+&twl {
+ compatible = "ti,twl4030";
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ rtc {
+ compatible = "ti,twl4030-rtc";
+ interrupts = <11>;
+ };
+
+ vdac: regulator@0 {
+ compatible = "ti,twl4030-vdac";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ vpll2: regulator@1 {
+ compatible = "ti,twl4030-vpll2";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ vmmc1: regulator@2 {
+ compatible = "ti,twl4030-vmmc1";
+ regulator-min-microvolt = <1850000>;
+ regulator-max-microvolt = <3150000>;
+ };
+};
diff --git a/arch/arm/boot/dts/twl6030.dtsi b/arch/arm/boot/dts/twl6030.dtsi
new file mode 100644
index 0000000..3b2f351
--- /dev/null
+++ b/arch/arm/boot/dts/twl6030.dtsi
@@ -0,0 +1,86 @@
+/*
+ * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/*
+ * Integrated Power Management Chip
+ * http://www.ti.com/lit/ds/symlink/twl6030.pdf
+ */
+&twl {
+ compatible = "ti,twl6030";
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ rtc {
+ compatible = "ti,twl4030-rtc";
+ interrupts = <11>;
+ };
+
+ vaux1: regulator@0 {
+ compatible = "ti,twl6030-vaux1";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <3000000>;
+ };
+
+ vaux2: regulator@1 {
+ compatible = "ti,twl6030-vaux2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <2800000>;
+ };
+
+ vaux3: regulator@2 {
+ compatible = "ti,twl6030-vaux3";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <3000000>;
+ };
+
+ vmmc: regulator@3 {
+ compatible = "ti,twl6030-vmmc";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <3000000>;
+ };
+
+ vpp: regulator@4 {
+ compatible = "ti,twl6030-vpp";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2500000>;
+ };
+
+ vusim: regulator@5 {
+ compatible = "ti,twl6030-vusim";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <2900000>;
+ };
+
+ vdac: regulator@6 {
+ compatible = "ti,twl6030-vdac";
+ };
+
+ vana: regulator@7 {
+ compatible = "ti,twl6030-vana";
+ };
+
+ vcxio: regulator@8 {
+ compatible = "ti,twl6030-vcxio";
+ };
+
+ vusb: regulator@9 {
+ compatible = "ti,twl6030-vusb";
+ };
+
+ v1v8: regulator@10 {
+ compatible = "ti,twl6030-v1v8";
+ };
+
+ v2v1: regulator@11 {
+ compatible = "ti,twl6030-v2v1";
+ };
+
+ clk32kg: regulator@12 {
+ compatible = "ti,twl6030-clk32kg";
+ };
+};
diff --git a/arch/arm/configs/spear3xx_defconfig b/arch/arm/configs/spear3xx_defconfig
index fea7e1f..7ed4291 100644
--- a/arch/arm/configs/spear3xx_defconfig
+++ b/arch/arm/configs/spear3xx_defconfig
@@ -2,33 +2,67 @@
CONFIG_SYSVIPC=y
CONFIG_BSD_PROCESS_ACCT=y
CONFIG_BLK_DEV_INITRD=y
-CONFIG_KALLSYMS_EXTRA_PASS=y
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
CONFIG_MODVERSIONS=y
+CONFIG_PARTITION_ADVANCED=y
CONFIG_PLAT_SPEAR=y
-CONFIG_BOARD_SPEAR300_EVB=y
-CONFIG_BOARD_SPEAR310_EVB=y
-CONFIG_BOARD_SPEAR320_EVB=y
+CONFIG_MACH_SPEAR300=y
+CONFIG_MACH_SPEAR310=y
+CONFIG_MACH_SPEAR320=y
CONFIG_BINFMT_MISC=y
+CONFIG_NET=y
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_MTD=y
+CONFIG_MTD_NAND=y
+CONFIG_MTD_NAND_FSMC=y
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_SIZE=16384
+CONFIG_NETDEVICES=y
+# CONFIG_NET_VENDOR_BROADCOM is not set
+# CONFIG_NET_VENDOR_CIRRUS is not set
+# CONFIG_NET_VENDOR_FARADAY is not set
+# CONFIG_NET_VENDOR_INTEL is not set
+# CONFIG_NET_VENDOR_MICREL is not set
+# CONFIG_NET_VENDOR_NATSEMI is not set
+# CONFIG_NET_VENDOR_SEEQ is not set
+# CONFIG_NET_VENDOR_SMSC is not set
+CONFIG_STMMAC_ETH=y
+# CONFIG_WLAN is not set
CONFIG_INPUT_FF_MEMLESS=y
# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
-# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_KEYBOARD_ATKBD is not set
+CONFIG_KEYBOARD_SPEAR=y
# CONFIG_INPUT_MOUSE is not set
+# CONFIG_LEGACY_PTYS is not set
CONFIG_SERIAL_AMBA_PL011=y
CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
-# CONFIG_LEGACY_PTYS is not set
# CONFIG_HW_RANDOM is not set
CONFIG_RAW_DRIVER=y
CONFIG_MAX_RAW_DEVS=8192
+CONFIG_I2C=y
+CONFIG_I2C_DESIGNWARE_PLATFORM=y
+CONFIG_SPI=y
+CONFIG_SPI_PL022=y
CONFIG_GPIO_SYSFS=y
CONFIG_GPIO_PL061=y
# CONFIG_HWMON is not set
+CONFIG_WATCHDOG=y
+CONFIG_ARM_SP805_WATCHDOG=y
+CONFIG_FB=y
+CONFIG_FB_ARMCLCD=y
# CONFIG_HID_SUPPORT is not set
-# CONFIG_USB_SUPPORT is not set
+CONFIG_USB=y
+# CONFIG_USB_DEVICE_CLASS is not set
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_OHCI_HCD=y
+CONFIG_MMC=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_SPEAR=y
+CONFIG_RTC_CLASS=y
+CONFIG_DMADEVICES=y
+CONFIG_AMBA_PL08X=y
+CONFIG_DMATEST=m
CONFIG_EXT2_FS=y
CONFIG_EXT2_FS_XATTR=y
CONFIG_EXT2_FS_SECURITY=y
@@ -39,8 +73,6 @@
CONFIG_VFAT_FS=m
CONFIG_FAT_DEFAULT_IOCHARSET="ascii"
CONFIG_TMPFS=y
-CONFIG_PARTITION_ADVANCED=y
-CONFIG_NLS=y
CONFIG_NLS_DEFAULT="utf8"
CONFIG_NLS_CODEPAGE_437=y
CONFIG_NLS_ASCII=m
@@ -48,6 +80,4 @@
CONFIG_DEBUG_FS=y
CONFIG_DEBUG_KERNEL=y
CONFIG_DEBUG_SPINLOCK=y
-CONFIG_DEBUG_SPINLOCK_SLEEP=y
CONFIG_DEBUG_INFO=y
-# CONFIG_CRC32 is not set
diff --git a/arch/arm/configs/spear6xx_defconfig b/arch/arm/configs/spear6xx_defconfig
index cef2e83..cf94bc7 100644
--- a/arch/arm/configs/spear6xx_defconfig
+++ b/arch/arm/configs/spear6xx_defconfig
@@ -2,29 +2,58 @@
CONFIG_SYSVIPC=y
CONFIG_BSD_PROCESS_ACCT=y
CONFIG_BLK_DEV_INITRD=y
-CONFIG_KALLSYMS_EXTRA_PASS=y
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
CONFIG_MODVERSIONS=y
+CONFIG_PARTITION_ADVANCED=y
CONFIG_PLAT_SPEAR=y
CONFIG_ARCH_SPEAR6XX=y
-CONFIG_BOARD_SPEAR600_EVB=y
+CONFIG_BOARD_SPEAR600_DT=y
CONFIG_BINFMT_MISC=y
+CONFIG_NET=y
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_MTD=y
+CONFIG_MTD_NAND=y
+CONFIG_MTD_NAND_FSMC=y
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_SIZE=16384
+CONFIG_NETDEVICES=y
+# CONFIG_NET_VENDOR_BROADCOM is not set
+# CONFIG_NET_VENDOR_CIRRUS is not set
+# CONFIG_NET_VENDOR_FARADAY is not set
+# CONFIG_NET_VENDOR_INTEL is not set
+# CONFIG_NET_VENDOR_MICREL is not set
+# CONFIG_NET_VENDOR_NATSEMI is not set
+# CONFIG_NET_VENDOR_SEEQ is not set
+# CONFIG_NET_VENDOR_SMSC is not set
+CONFIG_STMMAC_ETH=y
+# CONFIG_WLAN is not set
CONFIG_INPUT_FF_MEMLESS=y
# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_LEGACY_PTYS is not set
CONFIG_SERIAL_AMBA_PL011=y
CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
-# CONFIG_LEGACY_PTYS is not set
CONFIG_RAW_DRIVER=y
CONFIG_MAX_RAW_DEVS=8192
+CONFIG_I2C=y
+CONFIG_I2C_DESIGNWARE_PLATFORM=y
+CONFIG_SPI=y
+CONFIG_SPI_PL022=y
CONFIG_GPIO_SYSFS=y
CONFIG_GPIO_PL061=y
# CONFIG_HWMON is not set
+CONFIG_WATCHDOG=y
+CONFIG_ARM_SP805_WATCHDOG=y
# CONFIG_HID_SUPPORT is not set
-# CONFIG_USB_SUPPORT is not set
+CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_OHCI_HCD=y
+CONFIG_RTC_CLASS=y
+CONFIG_DMADEVICES=y
+CONFIG_AMBA_PL08X=y
+CONFIG_DMATEST=m
CONFIG_EXT2_FS=y
CONFIG_EXT2_FS_XATTR=y
CONFIG_EXT2_FS_SECURITY=y
@@ -35,8 +64,6 @@
CONFIG_VFAT_FS=m
CONFIG_FAT_DEFAULT_IOCHARSET="ascii"
CONFIG_TMPFS=y
-CONFIG_PARTITION_ADVANCED=y
-CONFIG_NLS=y
CONFIG_NLS_DEFAULT="utf8"
CONFIG_NLS_CODEPAGE_437=y
CONFIG_NLS_ASCII=m
@@ -44,6 +71,4 @@
CONFIG_DEBUG_FS=y
CONFIG_DEBUG_KERNEL=y
CONFIG_DEBUG_SPINLOCK=y
-CONFIG_DEBUG_SPINLOCK_SLEEP=y
CONFIG_DEBUG_INFO=y
-# CONFIG_CRC32 is not set
diff --git a/arch/arm/mach-omap2/board-generic.c b/arch/arm/mach-omap2/board-generic.c
index 098d183..7302ba7 100644
--- a/arch/arm/mach-omap2/board-generic.c
+++ b/arch/arm/mach-omap2/board-generic.c
@@ -15,7 +15,6 @@
#include <linux/of_irq.h>
#include <linux/of_platform.h>
#include <linux/irqdomain.h>
-#include <linux/i2c/twl.h>
#include <mach/hardware.h>
#include <asm/hardware/gic.h>
@@ -95,22 +94,6 @@
#endif
#ifdef CONFIG_ARCH_OMAP3
-static struct twl4030_platform_data beagle_twldata = {
- .irq_base = TWL4030_IRQ_BASE,
- .irq_end = TWL4030_IRQ_END,
-};
-
-static void __init omap3_i2c_init(void)
-{
- omap3_pmic_init("twl4030", &beagle_twldata);
-}
-
-static void __init omap3_init(void)
-{
- omap3_i2c_init();
- omap_generic_init();
-}
-
static const char *omap3_boards_compat[] __initdata = {
"ti,omap3",
NULL,
@@ -122,7 +105,7 @@
.init_early = omap3430_init_early,
.init_irq = omap_init_irq,
.handle_irq = omap3_intc_handle_irq,
- .init_machine = omap3_init,
+ .init_machine = omap_generic_init,
.timer = &omap3_timer,
.dt_compat = omap3_boards_compat,
.restart = omap_prcm_restart,
@@ -130,22 +113,6 @@
#endif
#ifdef CONFIG_ARCH_OMAP4
-static struct twl4030_platform_data sdp4430_twldata = {
- .irq_base = TWL6030_IRQ_BASE,
- .irq_end = TWL6030_IRQ_END,
-};
-
-static void __init omap4_i2c_init(void)
-{
- omap4_pmic_init("twl6030", &sdp4430_twldata, NULL, 0);
-}
-
-static void __init omap4_init(void)
-{
- omap4_i2c_init();
- omap_generic_init();
-}
-
static const char *omap4_boards_compat[] __initdata = {
"ti,omap4",
NULL,
@@ -157,7 +124,7 @@
.init_early = omap4430_init_early,
.init_irq = omap_init_irq,
.handle_irq = gic_handle_irq,
- .init_machine = omap4_init,
+ .init_machine = omap_generic_init,
.timer = &omap4_timer,
.dt_compat = omap4_boards_compat,
.restart = omap_prcm_restart,
diff --git a/arch/arm/mach-omap2/devices.c b/arch/arm/mach-omap2/devices.c
index e433603..98cab3a 100644
--- a/arch/arm/mach-omap2/devices.c
+++ b/arch/arm/mach-omap2/devices.c
@@ -705,7 +705,9 @@
omap_init_dmic();
omap_init_camera();
omap_init_mbox();
- omap_init_mcspi();
+ /* If dtb is there, the devices will be created dynamically */
+ if (!of_have_populated_dt())
+ omap_init_mcspi();
omap_init_pmu();
omap_hdq_init();
omap_init_sti();
diff --git a/arch/arm/mach-omap2/gpio.c b/arch/arm/mach-omap2/gpio.c
index 2f994e5..18f9c7b 100644
--- a/arch/arm/mach-omap2/gpio.c
+++ b/arch/arm/mach-omap2/gpio.c
@@ -20,6 +20,7 @@
#include <linux/err.h>
#include <linux/slab.h>
#include <linux/interrupt.h>
+#include <linux/of.h>
#include <plat/omap_hwmod.h>
#include <plat/omap_device.h>
@@ -146,7 +147,10 @@
*/
static int __init omap2_gpio_init(void)
{
- return omap_hwmod_for_each_by_class("gpio", omap2_gpio_dev_init,
- NULL);
+ /* If dtb is there, the devices will be created dynamically */
+ if (of_have_populated_dt())
+ return -ENODEV;
+
+ return omap_hwmod_for_each_by_class("gpio", omap2_gpio_dev_init, NULL);
}
postcore_initcall(omap2_gpio_init);
diff --git a/arch/arm/mach-shmobile/include/mach/common.h b/arch/arm/mach-shmobile/include/mach/common.h
index 83ad3fe..cc1d735 100644
--- a/arch/arm/mach-shmobile/include/mach/common.h
+++ b/arch/arm/mach-shmobile/include/mach/common.h
@@ -3,6 +3,8 @@
extern void shmobile_earlytimer_init(void);
extern struct sys_timer shmobile_timer;
+extern void shmobile_setup_delay(unsigned int max_cpu_core_mhz,
+ unsigned int mult, unsigned int div);
struct twd_local_timer;
void shmobile_twd_init(struct twd_local_timer *twd_local_timer);
extern void shmobile_setup_console(void);
diff --git a/arch/arm/mach-shmobile/include/mach/intc.h b/arch/arm/mach-shmobile/include/mach/intc.h
index 8b22258..a5603c7 100644
--- a/arch/arm/mach-shmobile/include/mach/intc.h
+++ b/arch/arm/mach-shmobile/include/mach/intc.h
@@ -142,6 +142,50 @@
p ## _sense_registers, p ## _ack_registers) \
}
+#define INTC_IRQ_PINS_16H(p, base, vect, str) \
+ \
+static struct resource p ## _resources[] __initdata = { \
+ [0] = { \
+ .start = base, \
+ .end = base + 0x64, \
+ .flags = IORESOURCE_MEM, \
+ }, \
+}; \
+ \
+enum { \
+ p ## _UNUSED = 0, \
+ INTC_IRQ_PINS_ENUM_16H(p), \
+}; \
+ \
+static struct intc_vect p ## _vectors[] __initdata = { \
+ INTC_IRQ_PINS_VECT_16H(p, vect), \
+}; \
+ \
+static struct intc_mask_reg p ## _mask_registers[] __initdata = { \
+ INTC_IRQ_PINS_MASK_16H(p, base), \
+}; \
+ \
+static struct intc_prio_reg p ## _prio_registers[] __initdata = { \
+ INTC_IRQ_PINS_PRIO_16H(p, base), \
+}; \
+ \
+static struct intc_sense_reg p ## _sense_registers[] __initdata = { \
+ INTC_IRQ_PINS_SENSE_16H(p, base), \
+}; \
+ \
+static struct intc_mask_reg p ## _ack_registers[] __initdata = { \
+ INTC_IRQ_PINS_ACK_16H(p, base), \
+}; \
+ \
+static struct intc_desc p ## _desc __initdata = { \
+ .name = str, \
+ .resource = p ## _resources, \
+ .num_resources = ARRAY_SIZE(p ## _resources), \
+ .hw = INTC_HW_DESC(p ## _vectors, NULL, \
+ p ## _mask_registers, p ## _prio_registers, \
+ p ## _sense_registers, p ## _ack_registers) \
+}
+
#define INTC_IRQ_PINS_32(p, base, vect, str) \
\
static struct resource p ## _resources[] __initdata = { \
diff --git a/arch/arm/mach-shmobile/include/mach/irqs.h b/arch/arm/mach-shmobile/include/mach/irqs.h
index 4e686cc2..06a5da3 100644
--- a/arch/arm/mach-shmobile/include/mach/irqs.h
+++ b/arch/arm/mach-shmobile/include/mach/irqs.h
@@ -7,7 +7,7 @@
#define gic_spi(nr) ((nr) + 32)
/* INTCS */
-#define INTCS_VECT_BASE 0x2200
+#define INTCS_VECT_BASE 0x3400
#define INTCS_VECT(n, vect) INTC_VECT((n), INTCS_VECT_BASE + (vect))
#define intcs_evt2irq(evt) evt2irq(INTCS_VECT_BASE + (evt))
diff --git a/arch/arm/mach-shmobile/intc-sh7372.c b/arch/arm/mach-shmobile/intc-sh7372.c
index 6447e0a..2587a22 100644
--- a/arch/arm/mach-shmobile/intc-sh7372.c
+++ b/arch/arm/mach-shmobile/intc-sh7372.c
@@ -19,6 +19,7 @@
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/interrupt.h>
+#include <linux/module.h>
#include <linux/irq.h>
#include <linux/io.h>
#include <linux/sh_intc.h>
@@ -305,14 +306,16 @@
intca_mask_registers, intca_prio_registers,
NULL);
-INTC_IRQ_PINS_32(intca_irq_pins, 0xe6900000,
- INTC_VECT, "sh7372-intca-irq-pins");
+INTC_IRQ_PINS_16(intca_irq_pins_lo, 0xe6900000,
+ INTC_VECT, "sh7372-intca-irq-lo");
+
+INTC_IRQ_PINS_16H(intca_irq_pins_hi, 0xe6900000,
+ INTC_VECT, "sh7372-intca-irq-hi");
+
enum {
UNUSED_INTCS = 0,
ENABLED_INTCS,
- INTCS,
-
/* interrupt sources INTCS */
/* IRQ0S - IRQ31S */
@@ -426,8 +429,6 @@
INTCS_VECT(CPORTS2R, 0x1a20),
/* CEC */
INTCS_VECT(JPU6E, 0x1a80),
-
- INTC_VECT(INTCS, 0xf80),
};
static struct intc_group intcs_groups[] __initdata = {
@@ -490,9 +491,6 @@
{ 0xffd5019c, 0xffd501dc, 8, /* IMR7SA3 / IMCR7SA3 */
{ MFIS2_INTCS, CPORTS2R, 0, 0,
JPU6E, 0, 0, 0 } },
- { 0xffd20104, 0, 16, /* INTAMASK */
- { 0, 0, 0, 0, 0, 0, 0, 0,
- 0, 0, 0, 0, 0, 0, 0, INTCS } },
};
/* Priority is needed for INTCA to receive the INTCS interrupt */
@@ -557,18 +555,30 @@
void __init sh7372_init_irq(void)
{
void __iomem *intevtsa;
+ int n;
intcs_ffd2 = ioremap_nocache(0xffd20000, PAGE_SIZE);
intevtsa = intcs_ffd2 + 0x100;
intcs_ffd5 = ioremap_nocache(0xffd50000, PAGE_SIZE);
register_intc_controller(&intca_desc);
- register_intc_controller(&intca_irq_pins_desc);
+ register_intc_controller(&intca_irq_pins_lo_desc);
+ register_intc_controller(&intca_irq_pins_hi_desc);
register_intc_controller(&intcs_desc);
+ /* setup dummy cascade chip for INTCS */
+ n = evt2irq(0xf80);
+ irq_alloc_desc_at(n, numa_node_id());
+ irq_set_chip_and_handler_name(n, &dummy_irq_chip,
+ handle_level_irq, "level");
+ set_irq_flags(n, IRQF_VALID); /* yuck */
+
/* demux using INTEVTSA */
- irq_set_handler_data(evt2irq(0xf80), (void *)intevtsa);
- irq_set_chained_handler(evt2irq(0xf80), intcs_demux);
+ irq_set_handler_data(n, (void *)intevtsa);
+ irq_set_chained_handler(n, intcs_demux);
+
+ /* unmask INTCS in INTAMASK */
+ iowrite16(0, intcs_ffd2 + 0x104);
}
static unsigned short ffd2[0x200];
diff --git a/arch/arm/mach-shmobile/setup-sh7372.c b/arch/arm/mach-shmobile/setup-sh7372.c
index 2fe8f83..4c7fece 100644
--- a/arch/arm/mach-shmobile/setup-sh7372.c
+++ b/arch/arm/mach-shmobile/setup-sh7372.c
@@ -22,6 +22,7 @@
#include <linux/interrupt.h>
#include <linux/irq.h>
#include <linux/platform_device.h>
+#include <linux/of_platform.h>
#include <linux/uio_driver.h>
#include <linux/delay.h>
#include <linux/input.h>
@@ -1092,3 +1093,50 @@
/* override timer setup with soc-specific code */
shmobile_timer.init = sh7372_earlytimer_init;
}
+
+#ifdef CONFIG_USE_OF
+
+void __init sh7372_add_early_devices_dt(void)
+{
+ shmobile_setup_delay(800, 1, 3); /* Cortex-A8 @ 800MHz */
+
+ early_platform_add_devices(sh7372_early_devices,
+ ARRAY_SIZE(sh7372_early_devices));
+
+ /* setup early console here as well */
+ shmobile_setup_console();
+}
+
+static const struct of_dev_auxdata sh7372_auxdata_lookup[] __initconst = {
+ { }
+};
+
+void __init sh7372_add_standard_devices_dt(void)
+{
+ /* clocks are setup late during boot in the case of DT */
+ sh7372_clock_init();
+
+ platform_add_devices(sh7372_early_devices,
+ ARRAY_SIZE(sh7372_early_devices));
+
+ of_platform_populate(NULL, of_default_bus_match_table,
+ sh7372_auxdata_lookup, NULL);
+}
+
+static const char *sh7372_boards_compat_dt[] __initdata = {
+ "renesas,sh7372",
+ NULL,
+};
+
+DT_MACHINE_START(SH7372_DT, "Generic SH7372 (Flattened Device Tree)")
+ .map_io = sh7372_map_io,
+ .init_early = sh7372_add_early_devices_dt,
+ .nr_irqs = NR_IRQS_LEGACY,
+ .init_irq = sh7372_init_irq,
+ .handle_irq = shmobile_handle_irq_intc,
+ .init_machine = sh7372_add_standard_devices_dt,
+ .timer = &shmobile_timer,
+ .dt_compat = sh7372_boards_compat_dt,
+MACHINE_END
+
+#endif /* CONFIG_USE_OF */
diff --git a/arch/arm/mach-shmobile/timer.c b/arch/arm/mach-shmobile/timer.c
index 2fba5f3..599e008 100644
--- a/arch/arm/mach-shmobile/timer.c
+++ b/arch/arm/mach-shmobile/timer.c
@@ -19,9 +19,26 @@
*
*/
#include <linux/platform_device.h>
+#include <linux/delay.h>
#include <asm/mach/time.h>
#include <asm/smp_twd.h>
+void __init shmobile_setup_delay(unsigned int max_cpu_core_mhz,
+ unsigned int mult, unsigned int div)
+{
+ /* calculate a worst-case loops-per-jiffy value
+ * based on maximum cpu core mhz setting and the
+ * __delay() implementation in arch/arm/lib/delay.S
+ *
+ * this will result in a longer delay than expected
+ * when the cpu core runs on lower frequencies.
+ */
+
+ unsigned int value = (1000000 * mult) / (HZ * div);
+
+ lpj_fine = max_cpu_core_mhz * value;
+}
+
static void __init shmobile_late_time_init(void)
{
/*
diff --git a/arch/arm/mach-spear3xx/Kconfig b/arch/arm/mach-spear3xx/Kconfig
index 2cee6b0..d9fe11c 100644
--- a/arch/arm/mach-spear3xx/Kconfig
+++ b/arch/arm/mach-spear3xx/Kconfig
@@ -5,39 +5,19 @@
if ARCH_SPEAR3XX
menu "SPEAr3xx Implementations"
-config BOARD_SPEAR300_EVB
- bool "SPEAr300 Evaluation Board"
- select MACH_SPEAR300
- help
- Supports ST SPEAr300 Evaluation Board
-
-config BOARD_SPEAR310_EVB
- bool "SPEAr310 Evaluation Board"
- select MACH_SPEAR310
- help
- Supports ST SPEAr310 Evaluation Board
-
-config BOARD_SPEAR320_EVB
- bool "SPEAr320 Evaluation Board"
- select MACH_SPEAR320
- help
- Supports ST SPEAr320 Evaluation Board
-
-endmenu
-
config MACH_SPEAR300
- bool "SPEAr300"
+ bool "SPEAr300 Machine support with Device Tree"
help
- Supports ST SPEAr300 Machine
+ Supports ST SPEAr300 machine configured via the device-tree
config MACH_SPEAR310
- bool "SPEAr310"
+ bool "SPEAr310 Machine support with Device Tree"
help
- Supports ST SPEAr310 Machine
+ Supports ST SPEAr310 machine configured via the device-tree
config MACH_SPEAR320
- bool "SPEAr320"
+ bool "SPEAr320 Machine support with Device Tree"
help
- Supports ST SPEAr320 Machine
-
+ Supports ST SPEAr320 machine configured via the device-tree
+endmenu
endif #ARCH_SPEAR3XX
diff --git a/arch/arm/mach-spear3xx/Makefile b/arch/arm/mach-spear3xx/Makefile
index b248624..17b5d83 100644
--- a/arch/arm/mach-spear3xx/Makefile
+++ b/arch/arm/mach-spear3xx/Makefile
@@ -3,24 +3,13 @@
#
# common files
-obj-y += spear3xx.o clock.o
+obj-$(CONFIG_ARCH_SPEAR3XX) += spear3xx.o clock.o
# spear300 specific files
obj-$(CONFIG_MACH_SPEAR300) += spear300.o
-# spear300 boards files
-obj-$(CONFIG_BOARD_SPEAR300_EVB) += spear300_evb.o
-
-
# spear310 specific files
obj-$(CONFIG_MACH_SPEAR310) += spear310.o
-# spear310 boards files
-obj-$(CONFIG_BOARD_SPEAR310_EVB) += spear310_evb.o
-
-
# spear320 specific files
obj-$(CONFIG_MACH_SPEAR320) += spear320.o
-
-# spear320 boards files
-obj-$(CONFIG_BOARD_SPEAR320_EVB) += spear320_evb.o
diff --git a/arch/arm/mach-spear3xx/Makefile.boot b/arch/arm/mach-spear3xx/Makefile.boot
index 4674a4c..d93e217 100644
--- a/arch/arm/mach-spear3xx/Makefile.boot
+++ b/arch/arm/mach-spear3xx/Makefile.boot
@@ -1,3 +1,7 @@
zreladdr-y += 0x00008000
params_phys-y := 0x00000100
initrd_phys-y := 0x00800000
+
+dtb-$(CONFIG_MACH_SPEAR300) += spear300-evb.dtb
+dtb-$(CONFIG_MACH_SPEAR310) += spear310-evb.dtb
+dtb-$(CONFIG_MACH_SPEAR320) += spear320-evb.dtb
diff --git a/arch/arm/mach-spear3xx/clock.c b/arch/arm/mach-spear3xx/clock.c
index 6c4841f..cd6c110 100644
--- a/arch/arm/mach-spear3xx/clock.c
+++ b/arch/arm/mach-spear3xx/clock.c
@@ -11,12 +11,112 @@
* warranty of any kind, whether express or implied.
*/
+#include <linux/clkdev.h>
#include <linux/init.h>
#include <linux/io.h>
#include <linux/kernel.h>
+#include <linux/of_platform.h>
#include <asm/mach-types.h>
#include <plat/clock.h>
#include <mach/misc_regs.h>
+#include <mach/spear.h>
+
+#define PLL1_CTR (MISC_BASE + 0x008)
+#define PLL1_FRQ (MISC_BASE + 0x00C)
+#define PLL1_MOD (MISC_BASE + 0x010)
+#define PLL2_CTR (MISC_BASE + 0x014)
+/* PLL_CTR register masks */
+#define PLL_ENABLE 2
+#define PLL_MODE_SHIFT 4
+#define PLL_MODE_MASK 0x3
+#define PLL_MODE_NORMAL 0
+#define PLL_MODE_FRACTION 1
+#define PLL_MODE_DITH_DSB 2
+#define PLL_MODE_DITH_SSB 3
+
+#define PLL2_FRQ (MISC_BASE + 0x018)
+/* PLL FRQ register masks */
+#define PLL_DIV_N_SHIFT 0
+#define PLL_DIV_N_MASK 0xFF
+#define PLL_DIV_P_SHIFT 8
+#define PLL_DIV_P_MASK 0x7
+#define PLL_NORM_FDBK_M_SHIFT 24
+#define PLL_NORM_FDBK_M_MASK 0xFF
+#define PLL_DITH_FDBK_M_SHIFT 16
+#define PLL_DITH_FDBK_M_MASK 0xFFFF
+
+#define PLL2_MOD (MISC_BASE + 0x01C)
+#define PLL_CLK_CFG (MISC_BASE + 0x020)
+#define CORE_CLK_CFG (MISC_BASE + 0x024)
+/* CORE CLK CFG register masks */
+#define PLL_HCLK_RATIO_SHIFT 10
+#define PLL_HCLK_RATIO_MASK 0x3
+#define HCLK_PCLK_RATIO_SHIFT 8
+#define HCLK_PCLK_RATIO_MASK 0x3
+
+#define PERIP_CLK_CFG (MISC_BASE + 0x028)
+/* PERIP_CLK_CFG register masks */
+#define UART_CLK_SHIFT 4
+#define UART_CLK_MASK 0x1
+#define FIRDA_CLK_SHIFT 5
+#define FIRDA_CLK_MASK 0x3
+#define GPT0_CLK_SHIFT 8
+#define GPT1_CLK_SHIFT 11
+#define GPT2_CLK_SHIFT 12
+#define GPT_CLK_MASK 0x1
+#define AUX_CLK_PLL3_VAL 0
+#define AUX_CLK_PLL1_VAL 1
+
+#define PERIP1_CLK_ENB (MISC_BASE + 0x02C)
+/* PERIP1_CLK_ENB register masks */
+#define UART_CLK_ENB 3
+#define SSP_CLK_ENB 5
+#define I2C_CLK_ENB 7
+#define JPEG_CLK_ENB 8
+#define FIRDA_CLK_ENB 10
+#define GPT1_CLK_ENB 11
+#define GPT2_CLK_ENB 12
+#define ADC_CLK_ENB 15
+#define RTC_CLK_ENB 17
+#define GPIO_CLK_ENB 18
+#define DMA_CLK_ENB 19
+#define SMI_CLK_ENB 21
+#define GMAC_CLK_ENB 23
+#define USBD_CLK_ENB 24
+#define USBH_CLK_ENB 25
+#define C3_CLK_ENB 31
+
+#define RAS_CLK_ENB (MISC_BASE + 0x034)
+
+#define PRSC1_CLK_CFG (MISC_BASE + 0x044)
+#define PRSC2_CLK_CFG (MISC_BASE + 0x048)
+#define PRSC3_CLK_CFG (MISC_BASE + 0x04C)
+/* gpt synthesizer register masks */
+#define GPT_MSCALE_SHIFT 0
+#define GPT_MSCALE_MASK 0xFFF
+#define GPT_NSCALE_SHIFT 12
+#define GPT_NSCALE_MASK 0xF
+
+#define AMEM_CLK_CFG (MISC_BASE + 0x050)
+#define EXPI_CLK_CFG (MISC_BASE + 0x054)
+#define CLCD_CLK_SYNT (MISC_BASE + 0x05C)
+#define FIRDA_CLK_SYNT (MISC_BASE + 0x060)
+#define UART_CLK_SYNT (MISC_BASE + 0x064)
+#define GMAC_CLK_SYNT (MISC_BASE + 0x068)
+#define RAS1_CLK_SYNT (MISC_BASE + 0x06C)
+#define RAS2_CLK_SYNT (MISC_BASE + 0x070)
+#define RAS3_CLK_SYNT (MISC_BASE + 0x074)
+#define RAS4_CLK_SYNT (MISC_BASE + 0x078)
+/* aux clk synthesiser register masks for irda to ras4 */
+#define AUX_SYNT_ENB 31
+#define AUX_EQ_SEL_SHIFT 30
+#define AUX_EQ_SEL_MASK 1
+#define AUX_EQ1_SEL 0
+#define AUX_EQ2_SEL 1
+#define AUX_XSCALE_SHIFT 16
+#define AUX_XSCALE_MASK 0xFFF
+#define AUX_YSCALE_SHIFT 0
+#define AUX_YSCALE_MASK 0xFFF
/* root clks */
/* 32 KHz oscillator clock */
@@ -411,6 +511,21 @@
.recalc = &follow_parent,
};
+/* clock derived from usbh clk */
+/* usbh0 clock */
+static struct clk usbh0_clk = {
+ .flags = ALWAYS_ENABLED,
+ .pclk = &usbh_clk,
+ .recalc = &follow_parent,
+};
+
+/* usbh1 clock */
+static struct clk usbh1_clk = {
+ .flags = ALWAYS_ENABLED,
+ .pclk = &usbh_clk,
+ .recalc = &follow_parent,
+};
+
/* clock derived from ahb clk */
/* apb masks structure */
static struct bus_clk_masks apb_masks = {
@@ -652,109 +767,126 @@
/* array of all spear 3xx clock lookups */
static struct clk_lookup spear_clk_lookups[] = {
- { .con_id = "apb_pclk", .clk = &dummy_apb_pclk},
+ CLKDEV_INIT(NULL, "apb_pclk", &dummy_apb_pclk),
/* root clks */
- { .con_id = "osc_32k_clk", .clk = &osc_32k_clk},
- { .con_id = "osc_24m_clk", .clk = &osc_24m_clk},
+ CLKDEV_INIT(NULL, "osc_32k_clk", &osc_32k_clk),
+ CLKDEV_INIT(NULL, "osc_24m_clk", &osc_24m_clk),
/* clock derived from 32 KHz osc clk */
- { .dev_id = "rtc-spear", .clk = &rtc_clk},
+ CLKDEV_INIT("fc900000.rtc", NULL, &rtc_clk),
/* clock derived from 24 MHz osc clk */
- { .con_id = "pll1_clk", .clk = &pll1_clk},
- { .con_id = "pll3_48m_clk", .clk = &pll3_48m_clk},
- { .dev_id = "wdt", .clk = &wdt_clk},
+ CLKDEV_INIT(NULL, "pll1_clk", &pll1_clk),
+ CLKDEV_INIT(NULL, "pll3_48m_clk", &pll3_48m_clk),
+ CLKDEV_INIT("fc880000.wdt", NULL, &wdt_clk),
/* clock derived from pll1 clk */
- { .con_id = "cpu_clk", .clk = &cpu_clk},
- { .con_id = "ahb_clk", .clk = &ahb_clk},
- { .con_id = "uart_synth_clk", .clk = &uart_synth_clk},
- { .con_id = "firda_synth_clk", .clk = &firda_synth_clk},
- { .con_id = "gpt0_synth_clk", .clk = &gpt0_synth_clk},
- { .con_id = "gpt1_synth_clk", .clk = &gpt1_synth_clk},
- { .con_id = "gpt2_synth_clk", .clk = &gpt2_synth_clk},
- { .dev_id = "uart", .clk = &uart_clk},
- { .dev_id = "firda", .clk = &firda_clk},
- { .dev_id = "gpt0", .clk = &gpt0_clk},
- { .dev_id = "gpt1", .clk = &gpt1_clk},
- { .dev_id = "gpt2", .clk = &gpt2_clk},
+ CLKDEV_INIT(NULL, "cpu_clk", &cpu_clk),
+ CLKDEV_INIT(NULL, "ahb_clk", &ahb_clk),
+ CLKDEV_INIT(NULL, "uart_synth_clk", &uart_synth_clk),
+ CLKDEV_INIT(NULL, "firda_synth_clk", &firda_synth_clk),
+ CLKDEV_INIT(NULL, "gpt0_synth_clk", &gpt0_synth_clk),
+ CLKDEV_INIT(NULL, "gpt1_synth_clk", &gpt1_synth_clk),
+ CLKDEV_INIT(NULL, "gpt2_synth_clk", &gpt2_synth_clk),
+ CLKDEV_INIT("d0000000.serial", NULL, &uart_clk),
+ CLKDEV_INIT("firda", NULL, &firda_clk),
+ CLKDEV_INIT("gpt0", NULL, &gpt0_clk),
+ CLKDEV_INIT("gpt1", NULL, &gpt1_clk),
+ CLKDEV_INIT("gpt2", NULL, &gpt2_clk),
/* clock derived from pll3 clk */
- { .dev_id = "designware_udc", .clk = &usbd_clk},
- { .con_id = "usbh_clk", .clk = &usbh_clk},
+ CLKDEV_INIT("designware_udc", NULL, &usbd_clk),
+ CLKDEV_INIT(NULL, "usbh_clk", &usbh_clk),
+ /* clock derived from usbh clk */
+ CLKDEV_INIT(NULL, "usbh.0_clk", &usbh0_clk),
+ CLKDEV_INIT(NULL, "usbh.1_clk", &usbh1_clk),
/* clock derived from ahb clk */
- { .con_id = "apb_clk", .clk = &apb_clk},
- { .dev_id = "i2c_designware.0", .clk = &i2c_clk},
- { .dev_id = "dma", .clk = &dma_clk},
- { .dev_id = "jpeg", .clk = &jpeg_clk},
- { .dev_id = "gmac", .clk = &gmac_clk},
- { .dev_id = "smi", .clk = &smi_clk},
- { .dev_id = "c3", .clk = &c3_clk},
+ CLKDEV_INIT(NULL, "apb_clk", &apb_clk),
+ CLKDEV_INIT("d0180000.i2c", NULL, &i2c_clk),
+ CLKDEV_INIT("fc400000.dma", NULL, &dma_clk),
+ CLKDEV_INIT("jpeg", NULL, &jpeg_clk),
+ CLKDEV_INIT("e0800000.eth", NULL, &gmac_clk),
+ CLKDEV_INIT("fc000000.flash", NULL, &smi_clk),
+ CLKDEV_INIT("c3", NULL, &c3_clk),
/* clock derived from apb clk */
- { .dev_id = "adc", .clk = &adc_clk},
- { .dev_id = "ssp-pl022.0", .clk = &ssp0_clk},
- { .dev_id = "gpio", .clk = &gpio_clk},
+ CLKDEV_INIT("adc", NULL, &adc_clk),
+ CLKDEV_INIT("d0100000.spi", NULL, &ssp0_clk),
+ CLKDEV_INIT("fc980000.gpio", NULL, &gpio_clk),
};
/* array of all spear 300 clock lookups */
#ifdef CONFIG_MACH_SPEAR300
static struct clk_lookup spear300_clk_lookups[] = {
- { .dev_id = "clcd", .clk = &clcd_clk},
- { .con_id = "fsmc", .clk = &fsmc_clk},
- { .dev_id = "gpio1", .clk = &gpio1_clk},
- { .dev_id = "keyboard", .clk = &kbd_clk},
- { .dev_id = "sdhci", .clk = &sdhci_clk},
+ CLKDEV_INIT("60000000.clcd", NULL, &clcd_clk),
+ CLKDEV_INIT("94000000.flash", NULL, &fsmc_clk),
+ CLKDEV_INIT("a9000000.gpio", NULL, &gpio1_clk),
+ CLKDEV_INIT("a0000000.kbd", NULL, &kbd_clk),
+ CLKDEV_INIT("70000000.sdhci", NULL, &sdhci_clk),
};
+
+void __init spear300_clk_init(void)
+{
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(spear_clk_lookups); i++)
+ clk_register(&spear_clk_lookups[i]);
+
+ for (i = 0; i < ARRAY_SIZE(spear300_clk_lookups); i++)
+ clk_register(&spear300_clk_lookups[i]);
+
+ clk_init();
+}
#endif
/* array of all spear 310 clock lookups */
#ifdef CONFIG_MACH_SPEAR310
static struct clk_lookup spear310_clk_lookups[] = {
- { .con_id = "fsmc", .clk = &fsmc_clk},
- { .con_id = "emi", .clk = &emi_clk},
- { .dev_id = "uart1", .clk = &uart1_clk},
- { .dev_id = "uart2", .clk = &uart2_clk},
- { .dev_id = "uart3", .clk = &uart3_clk},
- { .dev_id = "uart4", .clk = &uart4_clk},
- { .dev_id = "uart5", .clk = &uart5_clk},
+ CLKDEV_INIT("44000000.flash", NULL, &fsmc_clk),
+ CLKDEV_INIT(NULL, "emi", &emi_clk),
+ CLKDEV_INIT("b2000000.serial", NULL, &uart1_clk),
+ CLKDEV_INIT("b2080000.serial", NULL, &uart2_clk),
+ CLKDEV_INIT("b2100000.serial", NULL, &uart3_clk),
+ CLKDEV_INIT("b2180000.serial", NULL, &uart4_clk),
+ CLKDEV_INIT("b2200000.serial", NULL, &uart5_clk),
};
+
+void __init spear310_clk_init(void)
+{
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(spear_clk_lookups); i++)
+ clk_register(&spear_clk_lookups[i]);
+
+ for (i = 0; i < ARRAY_SIZE(spear310_clk_lookups); i++)
+ clk_register(&spear310_clk_lookups[i]);
+
+ clk_init();
+}
#endif
/* array of all spear 320 clock lookups */
#ifdef CONFIG_MACH_SPEAR320
static struct clk_lookup spear320_clk_lookups[] = {
- { .dev_id = "clcd", .clk = &clcd_clk},
- { .con_id = "fsmc", .clk = &fsmc_clk},
- { .dev_id = "i2c_designware.1", .clk = &i2c1_clk},
- { .con_id = "emi", .clk = &emi_clk},
- { .dev_id = "pwm", .clk = &pwm_clk},
- { .dev_id = "sdhci", .clk = &sdhci_clk},
- { .dev_id = "c_can_platform.0", .clk = &can0_clk},
- { .dev_id = "c_can_platform.1", .clk = &can1_clk},
- { .dev_id = "ssp-pl022.1", .clk = &ssp1_clk},
- { .dev_id = "ssp-pl022.2", .clk = &ssp2_clk},
- { .dev_id = "uart1", .clk = &uart1_clk},
- { .dev_id = "uart2", .clk = &uart2_clk},
+ CLKDEV_INIT("90000000.clcd", NULL, &clcd_clk),
+ CLKDEV_INIT("4c000000.flash", NULL, &fsmc_clk),
+ CLKDEV_INIT("a7000000.i2c", NULL, &i2c1_clk),
+ CLKDEV_INIT(NULL, "emi", &emi_clk),
+ CLKDEV_INIT("pwm", NULL, &pwm_clk),
+ CLKDEV_INIT("70000000.sdhci", NULL, &sdhci_clk),
+ CLKDEV_INIT("c_can_platform.0", NULL, &can0_clk),
+ CLKDEV_INIT("c_can_platform.1", NULL, &can1_clk),
+ CLKDEV_INIT("a5000000.spi", NULL, &ssp1_clk),
+ CLKDEV_INIT("a6000000.spi", NULL, &ssp2_clk),
+ CLKDEV_INIT("a3000000.serial", NULL, &uart1_clk),
+ CLKDEV_INIT("a4000000.serial", NULL, &uart2_clk),
};
-#endif
-void __init spear3xx_clk_init(void)
+void __init spear320_clk_init(void)
{
- int i, cnt;
- struct clk_lookup *lookups;
-
- if (machine_is_spear300()) {
- cnt = ARRAY_SIZE(spear300_clk_lookups);
- lookups = spear300_clk_lookups;
- } else if (machine_is_spear310()) {
- cnt = ARRAY_SIZE(spear310_clk_lookups);
- lookups = spear310_clk_lookups;
- } else {
- cnt = ARRAY_SIZE(spear320_clk_lookups);
- lookups = spear320_clk_lookups;
- }
+ int i;
for (i = 0; i < ARRAY_SIZE(spear_clk_lookups); i++)
clk_register(&spear_clk_lookups[i]);
- for (i = 0; i < cnt; i++)
- clk_register(&lookups[i]);
+ for (i = 0; i < ARRAY_SIZE(spear320_clk_lookups); i++)
+ clk_register(&spear320_clk_lookups[i]);
clk_init();
}
+#endif
diff --git a/arch/arm/mach-spear3xx/include/mach/generic.h b/arch/arm/mach-spear3xx/include/mach/generic.h
index 14276e5..e4f4d72 100644
--- a/arch/arm/mach-spear3xx/include/mach/generic.h
+++ b/arch/arm/mach-spear3xx/include/mach/generic.h
@@ -14,6 +14,7 @@
#ifndef __MACH_GENERIC_H
#define __MACH_GENERIC_H
+#include <linux/amba/pl08x.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/amba/bus.h>
@@ -21,26 +22,15 @@
#include <asm/mach/map.h>
#include <plat/padmux.h>
-/* spear3xx declarations */
-/*
- * Each GPT has 2 timer channels
- * Following GPT channels will be used as clock source and clockevent
- */
-#define SPEAR_GPT0_BASE SPEAR3XX_ML1_TMR_BASE
-#define SPEAR_GPT0_CHAN0_IRQ SPEAR3XX_IRQ_CPU_GPT1_1
-#define SPEAR_GPT0_CHAN1_IRQ SPEAR3XX_IRQ_CPU_GPT1_2
-
/* Add spear3xx family device structure declarations here */
-extern struct amba_device spear3xx_gpio_device;
-extern struct amba_device spear3xx_uart_device;
extern struct sys_timer spear3xx_timer;
+extern struct pl022_ssp_controller pl022_plat_data;
+extern struct pl08x_platform_data pl080_plat_data;
/* Add spear3xx family function declarations here */
-void __init spear3xx_clk_init(void);
-void __init spear_setup_timer(void);
+void __init spear_setup_timer(resource_size_t base, int irq);
void __init spear3xx_map_io(void);
-void __init spear3xx_init_irq(void);
-void __init spear3xx_init(void);
+void __init spear3xx_dt_init_irq(void);
void spear_restart(char, const char *);
@@ -99,9 +89,6 @@
/* spear300 declarations */
#ifdef CONFIG_MACH_SPEAR300
-/* Add spear300 machine device structure declarations here */
-extern struct amba_device spear300_gpio1_device;
-
/* pad mux modes */
extern struct pmx_mode spear300_nand_mode;
extern struct pmx_mode spear300_nor_mode;
@@ -133,16 +120,13 @@
extern struct pmx_dev spear300_pmx_telecom_sdhci_8bit;
extern struct pmx_dev spear300_pmx_gpio1;
-/* Add spear300 machine function declarations here */
-void __init spear300_init(struct pmx_mode *pmx_mode, struct pmx_dev **pmx_devs,
- u8 pmx_dev_count);
+/* Add spear300 machine declarations here */
+void __init spear300_clk_init(void);
#endif /* CONFIG_MACH_SPEAR300 */
/* spear310 declarations */
#ifdef CONFIG_MACH_SPEAR310
-/* Add spear310 machine device structure declarations here */
-
/* pad mux devices */
extern struct pmx_dev spear310_pmx_emi_cs_0_1_4_5;
extern struct pmx_dev spear310_pmx_emi_cs_2_3;
@@ -153,16 +137,13 @@
extern struct pmx_dev spear310_pmx_rs485_0_1;
extern struct pmx_dev spear310_pmx_tdm0;
-/* Add spear310 machine function declarations here */
-void __init spear310_init(struct pmx_mode *pmx_mode, struct pmx_dev **pmx_devs,
- u8 pmx_dev_count);
+/* Add spear310 machine declarations here */
+void __init spear310_clk_init(void);
#endif /* CONFIG_MACH_SPEAR310 */
/* spear320 declarations */
#ifdef CONFIG_MACH_SPEAR320
-/* Add spear320 machine device structure declarations here */
-
/* pad mux modes */
extern struct pmx_mode spear320_auto_net_smii_mode;
extern struct pmx_mode spear320_auto_net_mii_mode;
@@ -193,9 +174,8 @@
extern struct pmx_dev spear320_pmx_smii1;
extern struct pmx_dev spear320_pmx_i2c1;
-/* Add spear320 machine function declarations here */
-void __init spear320_init(struct pmx_mode *pmx_mode, struct pmx_dev **pmx_devs,
- u8 pmx_dev_count);
+/* Add spear320 machine declarations here */
+void __init spear320_clk_init(void);
#endif /* CONFIG_MACH_SPEAR320 */
diff --git a/arch/arm/mach-spear3xx/include/mach/hardware.h b/arch/arm/mach-spear3xx/include/mach/hardware.h
index 4660c0d..40a8c178 100644
--- a/arch/arm/mach-spear3xx/include/mach/hardware.h
+++ b/arch/arm/mach-spear3xx/include/mach/hardware.h
@@ -1,23 +1 @@
-/*
- * arch/arm/mach-spear3xx/include/mach/hardware.h
- *
- * Hardware definitions for SPEAr3xx machine family
- *
- * Copyright (C) 2009 ST Microelectronics
- * Viresh Kumar<viresh.kumar@st.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#ifndef __MACH_HARDWARE_H
-#define __MACH_HARDWARE_H
-
-#include <plat/hardware.h>
-#include <mach/spear.h>
-
-/* Vitual to physical translation of statically mapped space */
-#define IO_ADDRESS(x) (x | 0xF0000000)
-
-#endif /* __MACH_HARDWARE_H */
+/* empty */
diff --git a/arch/arm/mach-spear3xx/include/mach/irqs.h b/arch/arm/mach-spear3xx/include/mach/irqs.h
index 6e26544..319620a 100644
--- a/arch/arm/mach-spear3xx/include/mach/irqs.h
+++ b/arch/arm/mach-spear3xx/include/mach/irqs.h
@@ -14,141 +14,15 @@
#ifndef __MACH_IRQS_H
#define __MACH_IRQS_H
-/* SPEAr3xx IRQ definitions */
-#define SPEAR3XX_IRQ_HW_ACCEL_MOD_0 0
+/* FIXME: probe all these from DT */
#define SPEAR3XX_IRQ_INTRCOMM_RAS_ARM 1
#define SPEAR3XX_IRQ_CPU_GPT1_1 2
-#define SPEAR3XX_IRQ_CPU_GPT1_2 3
-#define SPEAR3XX_IRQ_BASIC_GPT1_1 4
-#define SPEAR3XX_IRQ_BASIC_GPT1_2 5
-#define SPEAR3XX_IRQ_BASIC_GPT2_1 6
-#define SPEAR3XX_IRQ_BASIC_GPT2_2 7
-#define SPEAR3XX_IRQ_BASIC_DMA 8
-#define SPEAR3XX_IRQ_BASIC_SMI 9
-#define SPEAR3XX_IRQ_BASIC_RTC 10
-#define SPEAR3XX_IRQ_BASIC_GPIO 11
-#define SPEAR3XX_IRQ_BASIC_WDT 12
-#define SPEAR3XX_IRQ_DDR_CONTROLLER 13
-#define SPEAR3XX_IRQ_SYS_ERROR 14
-#define SPEAR3XX_IRQ_WAKEUP_RCV 15
-#define SPEAR3XX_IRQ_JPEG 16
-#define SPEAR3XX_IRQ_IRDA 17
-#define SPEAR3XX_IRQ_ADC 18
-#define SPEAR3XX_IRQ_UART 19
-#define SPEAR3XX_IRQ_SSP 20
-#define SPEAR3XX_IRQ_I2C 21
-#define SPEAR3XX_IRQ_MAC_1 22
-#define SPEAR3XX_IRQ_MAC_2 23
-#define SPEAR3XX_IRQ_USB_DEV 24
-#define SPEAR3XX_IRQ_USB_H_OHCI_0 25
-#define SPEAR3XX_IRQ_USB_H_EHCI_0 26
-#define SPEAR3XX_IRQ_USB_H_EHCI_1 SPEAR3XX_IRQ_USB_H_EHCI_0
-#define SPEAR3XX_IRQ_USB_H_OHCI_1 27
#define SPEAR3XX_IRQ_GEN_RAS_1 28
#define SPEAR3XX_IRQ_GEN_RAS_2 29
#define SPEAR3XX_IRQ_GEN_RAS_3 30
-#define SPEAR3XX_IRQ_HW_ACCEL_MOD_1 31
#define SPEAR3XX_IRQ_VIC_END 32
-
#define SPEAR3XX_VIRQ_START SPEAR3XX_IRQ_VIC_END
-/* SPEAr300 Virtual irq definitions */
-/* IRQs sharing IRQ_GEN_RAS_1 */
-#define SPEAR300_VIRQ_IT_PERS_S (SPEAR3XX_VIRQ_START + 0)
-#define SPEAR300_VIRQ_IT_CHANGE_S (SPEAR3XX_VIRQ_START + 1)
-#define SPEAR300_VIRQ_I2S (SPEAR3XX_VIRQ_START + 2)
-#define SPEAR300_VIRQ_TDM (SPEAR3XX_VIRQ_START + 3)
-#define SPEAR300_VIRQ_CAMERA_L (SPEAR3XX_VIRQ_START + 4)
-#define SPEAR300_VIRQ_CAMERA_F (SPEAR3XX_VIRQ_START + 5)
-#define SPEAR300_VIRQ_CAMERA_V (SPEAR3XX_VIRQ_START + 6)
-#define SPEAR300_VIRQ_KEYBOARD (SPEAR3XX_VIRQ_START + 7)
-#define SPEAR300_VIRQ_GPIO1 (SPEAR3XX_VIRQ_START + 8)
-
-/* IRQs sharing IRQ_GEN_RAS_3 */
-#define SPEAR300_IRQ_CLCD SPEAR3XX_IRQ_GEN_RAS_3
-
-/* IRQs sharing IRQ_INTRCOMM_RAS_ARM */
-#define SPEAR300_IRQ_SDHCI SPEAR3XX_IRQ_INTRCOMM_RAS_ARM
-
-/* SPEAr310 Virtual irq definitions */
-/* IRQs sharing IRQ_GEN_RAS_1 */
-#define SPEAR310_VIRQ_SMII0 (SPEAR3XX_VIRQ_START + 0)
-#define SPEAR310_VIRQ_SMII1 (SPEAR3XX_VIRQ_START + 1)
-#define SPEAR310_VIRQ_SMII2 (SPEAR3XX_VIRQ_START + 2)
-#define SPEAR310_VIRQ_SMII3 (SPEAR3XX_VIRQ_START + 3)
-#define SPEAR310_VIRQ_WAKEUP_SMII0 (SPEAR3XX_VIRQ_START + 4)
-#define SPEAR310_VIRQ_WAKEUP_SMII1 (SPEAR3XX_VIRQ_START + 5)
-#define SPEAR310_VIRQ_WAKEUP_SMII2 (SPEAR3XX_VIRQ_START + 6)
-#define SPEAR310_VIRQ_WAKEUP_SMII3 (SPEAR3XX_VIRQ_START + 7)
-
-/* IRQs sharing IRQ_GEN_RAS_2 */
-#define SPEAR310_VIRQ_UART1 (SPEAR3XX_VIRQ_START + 8)
-#define SPEAR310_VIRQ_UART2 (SPEAR3XX_VIRQ_START + 9)
-#define SPEAR310_VIRQ_UART3 (SPEAR3XX_VIRQ_START + 10)
-#define SPEAR310_VIRQ_UART4 (SPEAR3XX_VIRQ_START + 11)
-#define SPEAR310_VIRQ_UART5 (SPEAR3XX_VIRQ_START + 12)
-
-/* IRQs sharing IRQ_GEN_RAS_3 */
-#define SPEAR310_VIRQ_EMI (SPEAR3XX_VIRQ_START + 13)
-#define SPEAR310_VIRQ_PLGPIO (SPEAR3XX_VIRQ_START + 14)
-
-/* IRQs sharing IRQ_INTRCOMM_RAS_ARM */
-#define SPEAR310_VIRQ_TDM_HDLC (SPEAR3XX_VIRQ_START + 15)
-#define SPEAR310_VIRQ_RS485_0 (SPEAR3XX_VIRQ_START + 16)
-#define SPEAR310_VIRQ_RS485_1 (SPEAR3XX_VIRQ_START + 17)
-
-/* SPEAr320 Virtual irq definitions */
-/* IRQs sharing IRQ_GEN_RAS_1 */
-#define SPEAR320_VIRQ_EMI (SPEAR3XX_VIRQ_START + 0)
-#define SPEAR320_VIRQ_CLCD (SPEAR3XX_VIRQ_START + 1)
-#define SPEAR320_VIRQ_SPP (SPEAR3XX_VIRQ_START + 2)
-
-/* IRQs sharing IRQ_GEN_RAS_2 */
-#define SPEAR320_IRQ_SDHCI SPEAR3XX_IRQ_GEN_RAS_2
-
-/* IRQs sharing IRQ_GEN_RAS_3 */
-#define SPEAR320_VIRQ_PLGPIO (SPEAR3XX_VIRQ_START + 3)
-#define SPEAR320_VIRQ_I2S_PLAY (SPEAR3XX_VIRQ_START + 4)
-#define SPEAR320_VIRQ_I2S_REC (SPEAR3XX_VIRQ_START + 5)
-
-/* IRQs sharing IRQ_INTRCOMM_RAS_ARM */
-#define SPEAR320_VIRQ_CANU (SPEAR3XX_VIRQ_START + 6)
-#define SPEAR320_VIRQ_CANL (SPEAR3XX_VIRQ_START + 7)
-#define SPEAR320_VIRQ_UART1 (SPEAR3XX_VIRQ_START + 8)
-#define SPEAR320_VIRQ_UART2 (SPEAR3XX_VIRQ_START + 9)
-#define SPEAR320_VIRQ_SSP1 (SPEAR3XX_VIRQ_START + 10)
-#define SPEAR320_VIRQ_SSP2 (SPEAR3XX_VIRQ_START + 11)
-#define SPEAR320_VIRQ_SMII0 (SPEAR3XX_VIRQ_START + 12)
-#define SPEAR320_VIRQ_MII1_SMII1 (SPEAR3XX_VIRQ_START + 13)
-#define SPEAR320_VIRQ_WAKEUP_SMII0 (SPEAR3XX_VIRQ_START + 14)
-#define SPEAR320_VIRQ_WAKEUP_MII1_SMII1 (SPEAR3XX_VIRQ_START + 15)
-#define SPEAR320_VIRQ_I2C1 (SPEAR3XX_VIRQ_START + 16)
-
-/*
- * GPIO pins virtual irqs
- * Use the lowest number for the GPIO virtual IRQs base on which subarchs
- * we have compiled in
- */
-#if defined(CONFIG_MACH_SPEAR310)
-#define SPEAR3XX_GPIO_INT_BASE (SPEAR3XX_VIRQ_START + 18)
-#elif defined(CONFIG_MACH_SPEAR320)
-#define SPEAR3XX_GPIO_INT_BASE (SPEAR3XX_VIRQ_START + 17)
-#else
-#define SPEAR3XX_GPIO_INT_BASE (SPEAR3XX_VIRQ_START + 9)
-#endif
-
-#define SPEAR300_GPIO1_INT_BASE (SPEAR3XX_GPIO_INT_BASE + 8)
-#define SPEAR3XX_PLGPIO_COUNT 102
-
-#if defined(CONFIG_MACH_SPEAR310) || defined(CONFIG_MACH_SPEAR320)
-#define SPEAR3XX_PLGPIO_INT_BASE (SPEAR3XX_GPIO_INT_BASE + 8)
-#define SPEAR3XX_GPIO_INT_END (SPEAR3XX_PLGPIO_INT_BASE + \
- SPEAR3XX_PLGPIO_COUNT)
-#else
-#define SPEAR3XX_GPIO_INT_END (SPEAR300_GPIO1_INT_BASE + 8)
-#endif
-
-#define SPEAR3XX_VIRQ_END SPEAR3XX_GPIO_INT_END
-#define NR_IRQS SPEAR3XX_VIRQ_END
+#define NR_IRQS 160
#endif /* __MACH_IRQS_H */
diff --git a/arch/arm/mach-spear3xx/include/mach/misc_regs.h b/arch/arm/mach-spear3xx/include/mach/misc_regs.h
index 5bd8cd8..e0ab72e 100644
--- a/arch/arm/mach-spear3xx/include/mach/misc_regs.h
+++ b/arch/arm/mach-spear3xx/include/mach/misc_regs.h
@@ -14,151 +14,7 @@
#ifndef __MACH_MISC_REGS_H
#define __MACH_MISC_REGS_H
-#include <mach/hardware.h>
-
#define MISC_BASE IOMEM(VA_SPEAR3XX_ICM3_MISC_REG_BASE)
-
-#define SOC_CFG_CTR (MISC_BASE + 0x000)
-#define DIAG_CFG_CTR (MISC_BASE + 0x004)
-#define PLL1_CTR (MISC_BASE + 0x008)
-#define PLL1_FRQ (MISC_BASE + 0x00C)
-#define PLL1_MOD (MISC_BASE + 0x010)
-#define PLL2_CTR (MISC_BASE + 0x014)
-/* PLL_CTR register masks */
-#define PLL_ENABLE 2
-#define PLL_MODE_SHIFT 4
-#define PLL_MODE_MASK 0x3
-#define PLL_MODE_NORMAL 0
-#define PLL_MODE_FRACTION 1
-#define PLL_MODE_DITH_DSB 2
-#define PLL_MODE_DITH_SSB 3
-
-#define PLL2_FRQ (MISC_BASE + 0x018)
-/* PLL FRQ register masks */
-#define PLL_DIV_N_SHIFT 0
-#define PLL_DIV_N_MASK 0xFF
-#define PLL_DIV_P_SHIFT 8
-#define PLL_DIV_P_MASK 0x7
-#define PLL_NORM_FDBK_M_SHIFT 24
-#define PLL_NORM_FDBK_M_MASK 0xFF
-#define PLL_DITH_FDBK_M_SHIFT 16
-#define PLL_DITH_FDBK_M_MASK 0xFFFF
-
-#define PLL2_MOD (MISC_BASE + 0x01C)
-#define PLL_CLK_CFG (MISC_BASE + 0x020)
-#define CORE_CLK_CFG (MISC_BASE + 0x024)
-/* CORE CLK CFG register masks */
-#define PLL_HCLK_RATIO_SHIFT 10
-#define PLL_HCLK_RATIO_MASK 0x3
-#define HCLK_PCLK_RATIO_SHIFT 8
-#define HCLK_PCLK_RATIO_MASK 0x3
-
-#define PERIP_CLK_CFG (MISC_BASE + 0x028)
-/* PERIP_CLK_CFG register masks */
-#define UART_CLK_SHIFT 4
-#define UART_CLK_MASK 0x1
-#define FIRDA_CLK_SHIFT 5
-#define FIRDA_CLK_MASK 0x3
-#define GPT0_CLK_SHIFT 8
-#define GPT1_CLK_SHIFT 11
-#define GPT2_CLK_SHIFT 12
-#define GPT_CLK_MASK 0x1
-#define AUX_CLK_PLL3_VAL 0
-#define AUX_CLK_PLL1_VAL 1
-
-#define PERIP1_CLK_ENB (MISC_BASE + 0x02C)
-/* PERIP1_CLK_ENB register masks */
-#define UART_CLK_ENB 3
-#define SSP_CLK_ENB 5
-#define I2C_CLK_ENB 7
-#define JPEG_CLK_ENB 8
-#define FIRDA_CLK_ENB 10
-#define GPT1_CLK_ENB 11
-#define GPT2_CLK_ENB 12
-#define ADC_CLK_ENB 15
-#define RTC_CLK_ENB 17
-#define GPIO_CLK_ENB 18
-#define DMA_CLK_ENB 19
-#define SMI_CLK_ENB 21
-#define GMAC_CLK_ENB 23
-#define USBD_CLK_ENB 24
-#define USBH_CLK_ENB 25
-#define C3_CLK_ENB 31
-
-#define SOC_CORE_ID (MISC_BASE + 0x030)
-#define RAS_CLK_ENB (MISC_BASE + 0x034)
-#define PERIP1_SOF_RST (MISC_BASE + 0x038)
-/* PERIP1_SOF_RST register masks */
-#define JPEG_SOF_RST 8
-
-#define SOC_USER_ID (MISC_BASE + 0x03C)
-#define RAS_SOF_RST (MISC_BASE + 0x040)
-#define PRSC1_CLK_CFG (MISC_BASE + 0x044)
-#define PRSC2_CLK_CFG (MISC_BASE + 0x048)
-#define PRSC3_CLK_CFG (MISC_BASE + 0x04C)
-/* gpt synthesizer register masks */
-#define GPT_MSCALE_SHIFT 0
-#define GPT_MSCALE_MASK 0xFFF
-#define GPT_NSCALE_SHIFT 12
-#define GPT_NSCALE_MASK 0xF
-
-#define AMEM_CLK_CFG (MISC_BASE + 0x050)
-#define EXPI_CLK_CFG (MISC_BASE + 0x054)
-#define CLCD_CLK_SYNT (MISC_BASE + 0x05C)
-#define FIRDA_CLK_SYNT (MISC_BASE + 0x060)
-#define UART_CLK_SYNT (MISC_BASE + 0x064)
-#define GMAC_CLK_SYNT (MISC_BASE + 0x068)
-#define RAS1_CLK_SYNT (MISC_BASE + 0x06C)
-#define RAS2_CLK_SYNT (MISC_BASE + 0x070)
-#define RAS3_CLK_SYNT (MISC_BASE + 0x074)
-#define RAS4_CLK_SYNT (MISC_BASE + 0x078)
-/* aux clk synthesiser register masks for irda to ras4 */
-#define AUX_SYNT_ENB 31
-#define AUX_EQ_SEL_SHIFT 30
-#define AUX_EQ_SEL_MASK 1
-#define AUX_EQ1_SEL 0
-#define AUX_EQ2_SEL 1
-#define AUX_XSCALE_SHIFT 16
-#define AUX_XSCALE_MASK 0xFFF
-#define AUX_YSCALE_SHIFT 0
-#define AUX_YSCALE_MASK 0xFFF
-
-#define ICM1_ARB_CFG (MISC_BASE + 0x07C)
-#define ICM2_ARB_CFG (MISC_BASE + 0x080)
-#define ICM3_ARB_CFG (MISC_BASE + 0x084)
-#define ICM4_ARB_CFG (MISC_BASE + 0x088)
-#define ICM5_ARB_CFG (MISC_BASE + 0x08C)
-#define ICM6_ARB_CFG (MISC_BASE + 0x090)
-#define ICM7_ARB_CFG (MISC_BASE + 0x094)
-#define ICM8_ARB_CFG (MISC_BASE + 0x098)
-#define ICM9_ARB_CFG (MISC_BASE + 0x09C)
#define DMA_CHN_CFG (MISC_BASE + 0x0A0)
-#define USB2_PHY_CFG (MISC_BASE + 0x0A4)
-#define GMAC_CFG_CTR (MISC_BASE + 0x0A8)
-#define EXPI_CFG_CTR (MISC_BASE + 0x0AC)
-#define PRC1_LOCK_CTR (MISC_BASE + 0x0C0)
-#define PRC2_LOCK_CTR (MISC_BASE + 0x0C4)
-#define PRC3_LOCK_CTR (MISC_BASE + 0x0C8)
-#define PRC4_LOCK_CTR (MISC_BASE + 0x0CC)
-#define PRC1_IRQ_CTR (MISC_BASE + 0x0D0)
-#define PRC2_IRQ_CTR (MISC_BASE + 0x0D4)
-#define PRC3_IRQ_CTR (MISC_BASE + 0x0D8)
-#define PRC4_IRQ_CTR (MISC_BASE + 0x0DC)
-#define PWRDOWN_CFG_CTR (MISC_BASE + 0x0E0)
-#define COMPSSTL_1V8_CFG (MISC_BASE + 0x0E4)
-#define COMPSSTL_2V5_CFG (MISC_BASE + 0x0E8)
-#define COMPCOR_3V3_CFG (MISC_BASE + 0x0EC)
-#define SSTLPAD_CFG_CTR (MISC_BASE + 0x0F0)
-#define BIST1_CFG_CTR (MISC_BASE + 0x0F4)
-#define BIST2_CFG_CTR (MISC_BASE + 0x0F8)
-#define BIST3_CFG_CTR (MISC_BASE + 0x0FC)
-#define BIST4_CFG_CTR (MISC_BASE + 0x100)
-#define BIST5_CFG_CTR (MISC_BASE + 0x104)
-#define BIST1_STS_RES (MISC_BASE + 0x108)
-#define BIST2_STS_RES (MISC_BASE + 0x10C)
-#define BIST3_STS_RES (MISC_BASE + 0x110)
-#define BIST4_STS_RES (MISC_BASE + 0x114)
-#define BIST5_STS_RES (MISC_BASE + 0x118)
-#define SYSERR_CFG_CTR (MISC_BASE + 0x11C)
#endif /* __MACH_MISC_REGS_H */
diff --git a/arch/arm/mach-spear3xx/include/mach/spear.h b/arch/arm/mach-spear3xx/include/mach/spear.h
index 63fd983..6d4dadc 100644
--- a/arch/arm/mach-spear3xx/include/mach/spear.h
+++ b/arch/arm/mach-spear3xx/include/mach/spear.h
@@ -15,60 +15,27 @@
#define __MACH_SPEAR3XX_H
#include <asm/memory.h>
-#include <mach/spear300.h>
-#include <mach/spear310.h>
-#include <mach/spear320.h>
-
-#define SPEAR3XX_ML_SDRAM_BASE UL(0x00000000)
-
-#define SPEAR3XX_ICM9_BASE UL(0xC0000000)
/* ICM1 - Low speed connection */
#define SPEAR3XX_ICM1_2_BASE UL(0xD0000000)
+#define VA_SPEAR3XX_ICM1_2_BASE UL(0xFD000000)
#define SPEAR3XX_ICM1_UART_BASE UL(0xD0000000)
-#define VA_SPEAR3XX_ICM1_UART_BASE IO_ADDRESS(SPEAR3XX_ICM1_UART_BASE)
-#define SPEAR3XX_ICM1_ADC_BASE UL(0xD0080000)
+#define VA_SPEAR3XX_ICM1_UART_BASE (VA_SPEAR3XX_ICM1_2_BASE | SPEAR3XX_ICM1_UART_BASE)
#define SPEAR3XX_ICM1_SSP_BASE UL(0xD0100000)
-#define SPEAR3XX_ICM1_I2C_BASE UL(0xD0180000)
-#define SPEAR3XX_ICM1_JPEG_BASE UL(0xD0800000)
-#define SPEAR3XX_ICM1_IRDA_BASE UL(0xD1000000)
-#define SPEAR3XX_ICM1_SRAM_BASE UL(0xD2800000)
-
-/* ICM2 - Application Subsystem */
-#define SPEAR3XX_ICM2_HWACCEL0_BASE UL(0xD8800000)
-#define SPEAR3XX_ICM2_HWACCEL1_BASE UL(0xD9000000)
-
-/* ICM4 - High Speed Connection */
-#define SPEAR3XX_ICM4_BASE UL(0xE0000000)
-#define SPEAR3XX_ICM4_MII_BASE UL(0xE0800000)
-#define SPEAR3XX_ICM4_USBD_FIFO_BASE UL(0xE1000000)
-#define SPEAR3XX_ICM4_USBD_CSR_BASE UL(0xE1100000)
-#define SPEAR3XX_ICM4_USBD_PLDT_BASE UL(0xE1200000)
-#define SPEAR3XX_ICM4_USB_EHCI0_1_BASE UL(0xE1800000)
-#define SPEAR3XX_ICM4_USB_OHCI0_BASE UL(0xE1900000)
-#define SPEAR3XX_ICM4_USB_OHCI1_BASE UL(0xE2100000)
-#define SPEAR3XX_ICM4_USB_ARB_BASE UL(0xE2800000)
/* ML1 - Multi Layer CPU Subsystem */
#define SPEAR3XX_ICM3_ML1_2_BASE UL(0xF0000000)
-#define SPEAR3XX_ML1_TMR_BASE UL(0xF0000000)
-#define SPEAR3XX_ML1_VIC_BASE UL(0xF1100000)
-#define VA_SPEAR3XX_ML1_VIC_BASE IO_ADDRESS(SPEAR3XX_ML1_VIC_BASE)
+#define VA_SPEAR6XX_ML_CPU_BASE UL(0xF0000000)
+#define SPEAR3XX_CPU_TMR_BASE UL(0xF0000000)
/* ICM3 - Basic Subsystem */
-#define SPEAR3XX_ICM3_SMEM_BASE UL(0xF8000000)
#define SPEAR3XX_ICM3_SMI_CTRL_BASE UL(0xFC000000)
+#define VA_SPEAR3XX_ICM3_SMI_CTRL_BASE UL(0xFC000000)
#define SPEAR3XX_ICM3_DMA_BASE UL(0xFC400000)
-#define SPEAR3XX_ICM3_SDRAM_CTRL_BASE UL(0xFC600000)
-#define SPEAR3XX_ICM3_TMR0_BASE UL(0xFC800000)
-#define SPEAR3XX_ICM3_WDT_BASE UL(0xFC880000)
-#define SPEAR3XX_ICM3_RTC_BASE UL(0xFC900000)
-#define SPEAR3XX_ICM3_GPIO_BASE UL(0xFC980000)
#define SPEAR3XX_ICM3_SYS_CTRL_BASE UL(0xFCA00000)
-#define VA_SPEAR3XX_ICM3_SYS_CTRL_BASE IO_ADDRESS(SPEAR3XX_ICM3_SYS_CTRL_BASE)
+#define VA_SPEAR3XX_ICM3_SYS_CTRL_BASE (VA_SPEAR3XX_ICM3_SMI_CTRL_BASE | SPEAR3XX_ICM3_SYS_CTRL_BASE)
#define SPEAR3XX_ICM3_MISC_REG_BASE UL(0xFCA80000)
-#define VA_SPEAR3XX_ICM3_MISC_REG_BASE IO_ADDRESS(SPEAR3XX_ICM3_MISC_REG_BASE)
-#define SPEAR3XX_ICM3_TMR1_BASE UL(0xFCB00000)
+#define VA_SPEAR3XX_ICM3_MISC_REG_BASE (VA_SPEAR3XX_ICM3_SMI_CTRL_BASE | SPEAR3XX_ICM3_MISC_REG_BASE)
/* Debug uart for linux, will be used for debug and uncompress messages */
#define SPEAR_DBG_UART_BASE SPEAR3XX_ICM1_UART_BASE
diff --git a/arch/arm/mach-spear3xx/include/mach/spear300.h b/arch/arm/mach-spear3xx/include/mach/spear300.h
deleted file mode 100644
index 3b6ea07..0000000
--- a/arch/arm/mach-spear3xx/include/mach/spear300.h
+++ /dev/null
@@ -1,54 +0,0 @@
-/*
- * arch/arm/mach-spear3xx/include/mach/spear300.h
- *
- * SPEAr300 Machine specific definition
- *
- * Copyright (C) 2009 ST Microelectronics
- * Viresh Kumar<viresh.kumar@st.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#ifdef CONFIG_MACH_SPEAR300
-
-#ifndef __MACH_SPEAR300_H
-#define __MACH_SPEAR300_H
-
-/* Base address of various IPs */
-#define SPEAR300_TELECOM_BASE UL(0x50000000)
-
-/* Interrupt registers offsets and masks */
-#define SPEAR300_INT_ENB_MASK_REG 0x54
-#define SPEAR300_INT_STS_MASK_REG 0x58
-#define SPEAR300_IT_PERS_S_IRQ_MASK (1 << 0)
-#define SPEAR300_IT_CHANGE_S_IRQ_MASK (1 << 1)
-#define SPEAR300_I2S_IRQ_MASK (1 << 2)
-#define SPEAR300_TDM_IRQ_MASK (1 << 3)
-#define SPEAR300_CAMERA_L_IRQ_MASK (1 << 4)
-#define SPEAR300_CAMERA_F_IRQ_MASK (1 << 5)
-#define SPEAR300_CAMERA_V_IRQ_MASK (1 << 6)
-#define SPEAR300_KEYBOARD_IRQ_MASK (1 << 7)
-#define SPEAR300_GPIO1_IRQ_MASK (1 << 8)
-
-#define SPEAR300_SHIRQ_RAS1_MASK 0x1FF
-
-#define SPEAR300_CLCD_BASE UL(0x60000000)
-#define SPEAR300_SDHCI_BASE UL(0x70000000)
-#define SPEAR300_NAND_0_BASE UL(0x80000000)
-#define SPEAR300_NAND_1_BASE UL(0x84000000)
-#define SPEAR300_NAND_2_BASE UL(0x88000000)
-#define SPEAR300_NAND_3_BASE UL(0x8c000000)
-#define SPEAR300_NOR_0_BASE UL(0x90000000)
-#define SPEAR300_NOR_1_BASE UL(0x91000000)
-#define SPEAR300_NOR_2_BASE UL(0x92000000)
-#define SPEAR300_NOR_3_BASE UL(0x93000000)
-#define SPEAR300_FSMC_BASE UL(0x94000000)
-#define SPEAR300_SOC_CONFIG_BASE UL(0x99000000)
-#define SPEAR300_KEYBOARD_BASE UL(0xA0000000)
-#define SPEAR300_GPIO_BASE UL(0xA9000000)
-
-#endif /* __MACH_SPEAR300_H */
-
-#endif /* CONFIG_MACH_SPEAR300 */
diff --git a/arch/arm/mach-spear3xx/include/mach/spear310.h b/arch/arm/mach-spear3xx/include/mach/spear310.h
deleted file mode 100644
index 1567d0da..0000000
--- a/arch/arm/mach-spear3xx/include/mach/spear310.h
+++ /dev/null
@@ -1,58 +0,0 @@
-/*
- * arch/arm/mach-spear3xx/include/mach/spear310.h
- *
- * SPEAr310 Machine specific definition
- *
- * Copyright (C) 2009 ST Microelectronics
- * Viresh Kumar<viresh.kumar@st.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#ifdef CONFIG_MACH_SPEAR310
-
-#ifndef __MACH_SPEAR310_H
-#define __MACH_SPEAR310_H
-
-#define SPEAR310_NAND_BASE UL(0x40000000)
-#define SPEAR310_FSMC_BASE UL(0x44000000)
-#define SPEAR310_UART1_BASE UL(0xB2000000)
-#define SPEAR310_UART2_BASE UL(0xB2080000)
-#define SPEAR310_UART3_BASE UL(0xB2100000)
-#define SPEAR310_UART4_BASE UL(0xB2180000)
-#define SPEAR310_UART5_BASE UL(0xB2200000)
-#define SPEAR310_HDLC_BASE UL(0xB2800000)
-#define SPEAR310_RS485_0_BASE UL(0xB3000000)
-#define SPEAR310_RS485_1_BASE UL(0xB3800000)
-#define SPEAR310_SOC_CONFIG_BASE UL(0xB4000000)
-
-/* Interrupt registers offsets and masks */
-#define SPEAR310_INT_STS_MASK_REG 0x04
-#define SPEAR310_SMII0_IRQ_MASK (1 << 0)
-#define SPEAR310_SMII1_IRQ_MASK (1 << 1)
-#define SPEAR310_SMII2_IRQ_MASK (1 << 2)
-#define SPEAR310_SMII3_IRQ_MASK (1 << 3)
-#define SPEAR310_WAKEUP_SMII0_IRQ_MASK (1 << 4)
-#define SPEAR310_WAKEUP_SMII1_IRQ_MASK (1 << 5)
-#define SPEAR310_WAKEUP_SMII2_IRQ_MASK (1 << 6)
-#define SPEAR310_WAKEUP_SMII3_IRQ_MASK (1 << 7)
-#define SPEAR310_UART1_IRQ_MASK (1 << 8)
-#define SPEAR310_UART2_IRQ_MASK (1 << 9)
-#define SPEAR310_UART3_IRQ_MASK (1 << 10)
-#define SPEAR310_UART4_IRQ_MASK (1 << 11)
-#define SPEAR310_UART5_IRQ_MASK (1 << 12)
-#define SPEAR310_EMI_IRQ_MASK (1 << 13)
-#define SPEAR310_TDM_HDLC_IRQ_MASK (1 << 14)
-#define SPEAR310_RS485_0_IRQ_MASK (1 << 15)
-#define SPEAR310_RS485_1_IRQ_MASK (1 << 16)
-
-#define SPEAR310_SHIRQ_RAS1_MASK 0x000FF
-#define SPEAR310_SHIRQ_RAS2_MASK 0x01F00
-#define SPEAR310_SHIRQ_RAS3_MASK 0x02000
-#define SPEAR310_SHIRQ_INTRCOMM_RAS_MASK 0x1C000
-
-#endif /* __MACH_SPEAR310_H */
-
-#endif /* CONFIG_MACH_SPEAR310 */
diff --git a/arch/arm/mach-spear3xx/include/mach/spear320.h b/arch/arm/mach-spear3xx/include/mach/spear320.h
deleted file mode 100644
index 8cfa83f..0000000
--- a/arch/arm/mach-spear3xx/include/mach/spear320.h
+++ /dev/null
@@ -1,67 +0,0 @@
-/*
- * arch/arm/mach-spear3xx/include/mach/spear320.h
- *
- * SPEAr320 Machine specific definition
- *
- * Copyright (C) 2009 ST Microelectronics
- * Viresh Kumar<viresh.kumar@st.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#ifdef CONFIG_MACH_SPEAR320
-
-#ifndef __MACH_SPEAR320_H
-#define __MACH_SPEAR320_H
-
-#define SPEAR320_EMI_CTRL_BASE UL(0x40000000)
-#define SPEAR320_FSMC_BASE UL(0x4C000000)
-#define SPEAR320_NAND_BASE UL(0x50000000)
-#define SPEAR320_I2S_BASE UL(0x60000000)
-#define SPEAR320_SDHCI_BASE UL(0x70000000)
-#define SPEAR320_CLCD_BASE UL(0x90000000)
-#define SPEAR320_PAR_PORT_BASE UL(0xA0000000)
-#define SPEAR320_CAN0_BASE UL(0xA1000000)
-#define SPEAR320_CAN1_BASE UL(0xA2000000)
-#define SPEAR320_UART1_BASE UL(0xA3000000)
-#define SPEAR320_UART2_BASE UL(0xA4000000)
-#define SPEAR320_SSP0_BASE UL(0xA5000000)
-#define SPEAR320_SSP1_BASE UL(0xA6000000)
-#define SPEAR320_I2C_BASE UL(0xA7000000)
-#define SPEAR320_PWM_BASE UL(0xA8000000)
-#define SPEAR320_SMII0_BASE UL(0xAA000000)
-#define SPEAR320_SMII1_BASE UL(0xAB000000)
-#define SPEAR320_SOC_CONFIG_BASE UL(0xB3000000)
-
-/* Interrupt registers offsets and masks */
-#define SPEAR320_INT_STS_MASK_REG 0x04
-#define SPEAR320_INT_CLR_MASK_REG 0x04
-#define SPEAR320_INT_ENB_MASK_REG 0x08
-#define SPEAR320_GPIO_IRQ_MASK (1 << 0)
-#define SPEAR320_I2S_PLAY_IRQ_MASK (1 << 1)
-#define SPEAR320_I2S_REC_IRQ_MASK (1 << 2)
-#define SPEAR320_EMI_IRQ_MASK (1 << 7)
-#define SPEAR320_CLCD_IRQ_MASK (1 << 8)
-#define SPEAR320_SPP_IRQ_MASK (1 << 9)
-#define SPEAR320_SDHCI_IRQ_MASK (1 << 10)
-#define SPEAR320_CAN_U_IRQ_MASK (1 << 11)
-#define SPEAR320_CAN_L_IRQ_MASK (1 << 12)
-#define SPEAR320_UART1_IRQ_MASK (1 << 13)
-#define SPEAR320_UART2_IRQ_MASK (1 << 14)
-#define SPEAR320_SSP1_IRQ_MASK (1 << 15)
-#define SPEAR320_SSP2_IRQ_MASK (1 << 16)
-#define SPEAR320_SMII0_IRQ_MASK (1 << 17)
-#define SPEAR320_MII1_SMII1_IRQ_MASK (1 << 18)
-#define SPEAR320_WAKEUP_SMII0_IRQ_MASK (1 << 19)
-#define SPEAR320_WAKEUP_MII1_SMII1_IRQ_MASK (1 << 20)
-#define SPEAR320_I2C1_IRQ_MASK (1 << 21)
-
-#define SPEAR320_SHIRQ_RAS1_MASK 0x000380
-#define SPEAR320_SHIRQ_RAS3_MASK 0x000007
-#define SPEAR320_SHIRQ_INTRCOMM_RAS_MASK 0x3FF800
-
-#endif /* __MACH_SPEAR320_H */
-
-#endif /* CONFIG_MACH_SPEAR320 */
diff --git a/arch/arm/mach-spear3xx/spear300.c b/arch/arm/mach-spear3xx/spear300.c
index f7db668..febcdd8 100644
--- a/arch/arm/mach-spear3xx/spear300.c
+++ b/arch/arm/mach-spear3xx/spear300.c
@@ -3,21 +3,62 @@
*
* SPEAr300 machine source file
*
- * Copyright (C) 2009 ST Microelectronics
- * Viresh Kumar<viresh.kumar@st.com>
+ * Copyright (C) 2009-2012 ST Microelectronics
+ * Viresh Kumar <viresh.kumar@st.com>
*
* This file is licensed under the terms of the GNU General Public
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
-#include <linux/types.h>
-#include <linux/amba/pl061.h>
-#include <linux/ptrace.h>
-#include <asm/irq.h>
+#define pr_fmt(fmt) "SPEAr300: " fmt
+
+#include <linux/amba/pl08x.h>
+#include <linux/of_platform.h>
+#include <asm/hardware/vic.h>
+#include <asm/mach/arch.h>
#include <plat/shirq.h>
#include <mach/generic.h>
-#include <mach/hardware.h>
+#include <mach/spear.h>
+
+/* Base address of various IPs */
+#define SPEAR300_TELECOM_BASE UL(0x50000000)
+
+/* Interrupt registers offsets and masks */
+#define SPEAR300_INT_ENB_MASK_REG 0x54
+#define SPEAR300_INT_STS_MASK_REG 0x58
+#define SPEAR300_IT_PERS_S_IRQ_MASK (1 << 0)
+#define SPEAR300_IT_CHANGE_S_IRQ_MASK (1 << 1)
+#define SPEAR300_I2S_IRQ_MASK (1 << 2)
+#define SPEAR300_TDM_IRQ_MASK (1 << 3)
+#define SPEAR300_CAMERA_L_IRQ_MASK (1 << 4)
+#define SPEAR300_CAMERA_F_IRQ_MASK (1 << 5)
+#define SPEAR300_CAMERA_V_IRQ_MASK (1 << 6)
+#define SPEAR300_KEYBOARD_IRQ_MASK (1 << 7)
+#define SPEAR300_GPIO1_IRQ_MASK (1 << 8)
+
+#define SPEAR300_SHIRQ_RAS1_MASK 0x1FF
+
+#define SPEAR300_SOC_CONFIG_BASE UL(0x99000000)
+
+
+/* SPEAr300 Virtual irq definitions */
+/* IRQs sharing IRQ_GEN_RAS_1 */
+#define SPEAR300_VIRQ_IT_PERS_S (SPEAR3XX_VIRQ_START + 0)
+#define SPEAR300_VIRQ_IT_CHANGE_S (SPEAR3XX_VIRQ_START + 1)
+#define SPEAR300_VIRQ_I2S (SPEAR3XX_VIRQ_START + 2)
+#define SPEAR300_VIRQ_TDM (SPEAR3XX_VIRQ_START + 3)
+#define SPEAR300_VIRQ_CAMERA_L (SPEAR3XX_VIRQ_START + 4)
+#define SPEAR300_VIRQ_CAMERA_F (SPEAR3XX_VIRQ_START + 5)
+#define SPEAR300_VIRQ_CAMERA_V (SPEAR3XX_VIRQ_START + 6)
+#define SPEAR300_VIRQ_KEYBOARD (SPEAR3XX_VIRQ_START + 7)
+#define SPEAR300_VIRQ_GPIO1 (SPEAR3XX_VIRQ_START + 8)
+
+/* IRQs sharing IRQ_GEN_RAS_3 */
+#define SPEAR300_IRQ_CLCD SPEAR3XX_IRQ_GEN_RAS_3
+
+/* IRQs sharing IRQ_INTRCOMM_RAS_ARM */
+#define SPEAR300_IRQ_SDHCI SPEAR3XX_IRQ_INTRCOMM_RAS_ARM
/* pad multiplexing support */
/* muxing registers */
@@ -423,45 +464,275 @@
},
};
-/* Add spear300 specific devices here */
-/* arm gpio1 device registration */
-static struct pl061_platform_data gpio1_plat_data = {
- .gpio_base = 8,
- .irq_base = SPEAR300_GPIO1_INT_BASE,
+/* padmux devices to enable */
+static struct pmx_dev *spear300_evb_pmx_devs[] = {
+ /* spear3xx specific devices */
+ &spear3xx_pmx_i2c,
+ &spear3xx_pmx_ssp_cs,
+ &spear3xx_pmx_ssp,
+ &spear3xx_pmx_mii,
+ &spear3xx_pmx_uart0,
+
+ /* spear300 specific devices */
+ &spear300_pmx_fsmc_2_chips,
+ &spear300_pmx_clcd,
+ &spear300_pmx_telecom_sdhci_4bit,
+ &spear300_pmx_gpio1,
};
-AMBA_APB_DEVICE(spear300_gpio1, "gpio1", 0, SPEAR300_GPIO_BASE,
- {SPEAR300_VIRQ_GPIO1}, &gpio1_plat_data);
+/* DMAC platform data's slave info */
+struct pl08x_channel_data spear300_dma_info[] = {
+ {
+ .bus_id = "uart0_rx",
+ .min_signal = 2,
+ .max_signal = 2,
+ .muxval = 0,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "uart0_tx",
+ .min_signal = 3,
+ .max_signal = 3,
+ .muxval = 0,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "ssp0_rx",
+ .min_signal = 8,
+ .max_signal = 8,
+ .muxval = 0,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "ssp0_tx",
+ .min_signal = 9,
+ .max_signal = 9,
+ .muxval = 0,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "i2c_rx",
+ .min_signal = 10,
+ .max_signal = 10,
+ .muxval = 0,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "i2c_tx",
+ .min_signal = 11,
+ .max_signal = 11,
+ .muxval = 0,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "irda",
+ .min_signal = 12,
+ .max_signal = 12,
+ .muxval = 0,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "adc",
+ .min_signal = 13,
+ .max_signal = 13,
+ .muxval = 0,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "to_jpeg",
+ .min_signal = 14,
+ .max_signal = 14,
+ .muxval = 0,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "from_jpeg",
+ .min_signal = 15,
+ .max_signal = 15,
+ .muxval = 0,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "ras0_rx",
+ .min_signal = 0,
+ .max_signal = 0,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "ras0_tx",
+ .min_signal = 1,
+ .max_signal = 1,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "ras1_rx",
+ .min_signal = 2,
+ .max_signal = 2,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "ras1_tx",
+ .min_signal = 3,
+ .max_signal = 3,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "ras2_rx",
+ .min_signal = 4,
+ .max_signal = 4,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "ras2_tx",
+ .min_signal = 5,
+ .max_signal = 5,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "ras3_rx",
+ .min_signal = 6,
+ .max_signal = 6,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "ras3_tx",
+ .min_signal = 7,
+ .max_signal = 7,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "ras4_rx",
+ .min_signal = 8,
+ .max_signal = 8,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "ras4_tx",
+ .min_signal = 9,
+ .max_signal = 9,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "ras5_rx",
+ .min_signal = 10,
+ .max_signal = 10,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "ras5_tx",
+ .min_signal = 11,
+ .max_signal = 11,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "ras6_rx",
+ .min_signal = 12,
+ .max_signal = 12,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "ras6_tx",
+ .min_signal = 13,
+ .max_signal = 13,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "ras7_rx",
+ .min_signal = 14,
+ .max_signal = 14,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "ras7_tx",
+ .min_signal = 15,
+ .max_signal = 15,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ },
+};
-/* spear300 routines */
-void __init spear300_init(struct pmx_mode *pmx_mode, struct pmx_dev **pmx_devs,
- u8 pmx_dev_count)
+/* Add SPEAr300 auxdata to pass platform data */
+static struct of_dev_auxdata spear300_auxdata_lookup[] __initdata = {
+ OF_DEV_AUXDATA("arm,pl022", SPEAR3XX_ICM1_SSP_BASE, NULL,
+ &pl022_plat_data),
+ OF_DEV_AUXDATA("arm,pl080", SPEAR3XX_ICM3_DMA_BASE, NULL,
+ &pl080_plat_data),
+ {}
+};
+
+static void __init spear300_dt_init(void)
{
- int ret = 0;
+ int ret = -EINVAL;
- /* call spear3xx family common init function */
- spear3xx_init();
+ pl080_plat_data.slave_channels = spear300_dma_info;
+ pl080_plat_data.num_slave_channels = ARRAY_SIZE(spear300_dma_info);
+
+ of_platform_populate(NULL, of_default_bus_match_table,
+ spear300_auxdata_lookup, NULL);
/* shared irq registration */
shirq_ras1.regs.base = ioremap(SPEAR300_TELECOM_BASE, SZ_4K);
if (shirq_ras1.regs.base) {
ret = spear_shirq_register(&shirq_ras1);
if (ret)
- printk(KERN_ERR "Error registering Shared IRQ\n");
+ pr_err("Error registering Shared IRQ\n");
}
- /* pmx initialization */
- pmx_driver.mode = pmx_mode;
- pmx_driver.devs = pmx_devs;
- pmx_driver.devs_count = pmx_dev_count;
+ if (of_machine_is_compatible("st,spear300-evb")) {
+ /* pmx initialization */
+ pmx_driver.mode = &spear300_photo_frame_mode;
+ pmx_driver.devs = spear300_evb_pmx_devs;
+ pmx_driver.devs_count = ARRAY_SIZE(spear300_evb_pmx_devs);
- pmx_driver.base = ioremap(SPEAR300_SOC_CONFIG_BASE, SZ_4K);
- if (pmx_driver.base) {
- ret = pmx_register(&pmx_driver);
+ pmx_driver.base = ioremap(SPEAR300_SOC_CONFIG_BASE, SZ_4K);
+ if (pmx_driver.base) {
+ ret = pmx_register(&pmx_driver);
+ if (ret)
+ pr_err("padmux: registration failed. err no: %d\n",
+ ret);
+ /* Free Mapping, device selection already done */
+ iounmap(pmx_driver.base);
+ }
+
if (ret)
- printk(KERN_ERR "padmux: registration failed. err no"
- ": %d\n", ret);
- /* Free Mapping, device selection already done */
- iounmap(pmx_driver.base);
+ pr_err("Initialization Failed");
}
}
+
+static const char * const spear300_dt_board_compat[] = {
+ "st,spear300",
+ "st,spear300-evb",
+ NULL,
+};
+
+static void __init spear300_map_io(void)
+{
+ spear3xx_map_io();
+ spear300_clk_init();
+}
+
+DT_MACHINE_START(SPEAR300_DT, "ST SPEAr300 SoC with Flattened Device Tree")
+ .map_io = spear300_map_io,
+ .init_irq = spear3xx_dt_init_irq,
+ .handle_irq = vic_handle_irq,
+ .timer = &spear3xx_timer,
+ .init_machine = spear300_dt_init,
+ .restart = spear_restart,
+ .dt_compat = spear300_dt_board_compat,
+MACHINE_END
diff --git a/arch/arm/mach-spear3xx/spear300_evb.c b/arch/arm/mach-spear3xx/spear300_evb.c
deleted file mode 100644
index 3462ab9..0000000
--- a/arch/arm/mach-spear3xx/spear300_evb.c
+++ /dev/null
@@ -1,75 +0,0 @@
-/*
- * arch/arm/mach-spear3xx/spear300_evb.c
- *
- * SPEAr300 evaluation board source file
- *
- * Copyright (C) 2009 ST Microelectronics
- * Viresh Kumar<viresh.kumar@st.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <asm/hardware/vic.h>
-#include <asm/mach/arch.h>
-#include <asm/mach-types.h>
-#include <mach/generic.h>
-#include <mach/hardware.h>
-
-/* padmux devices to enable */
-static struct pmx_dev *pmx_devs[] = {
- /* spear3xx specific devices */
- &spear3xx_pmx_i2c,
- &spear3xx_pmx_ssp_cs,
- &spear3xx_pmx_ssp,
- &spear3xx_pmx_mii,
- &spear3xx_pmx_uart0,
-
- /* spear300 specific devices */
- &spear300_pmx_fsmc_2_chips,
- &spear300_pmx_clcd,
- &spear300_pmx_telecom_sdhci_4bit,
- &spear300_pmx_gpio1,
-};
-
-static struct amba_device *amba_devs[] __initdata = {
- /* spear3xx specific devices */
- &spear3xx_gpio_device,
- &spear3xx_uart_device,
-
- /* spear300 specific devices */
- &spear300_gpio1_device,
-};
-
-static struct platform_device *plat_devs[] __initdata = {
- /* spear3xx specific devices */
-
- /* spear300 specific devices */
-};
-
-static void __init spear300_evb_init(void)
-{
- unsigned int i;
-
- /* call spear300 machine init function */
- spear300_init(&spear300_photo_frame_mode, pmx_devs,
- ARRAY_SIZE(pmx_devs));
-
- /* Add Platform Devices */
- platform_add_devices(plat_devs, ARRAY_SIZE(plat_devs));
-
- /* Add Amba Devices */
- for (i = 0; i < ARRAY_SIZE(amba_devs); i++)
- amba_device_register(amba_devs[i], &iomem_resource);
-}
-
-MACHINE_START(SPEAR300, "ST-SPEAR300-EVB")
- .atag_offset = 0x100,
- .map_io = spear3xx_map_io,
- .init_irq = spear3xx_init_irq,
- .handle_irq = vic_handle_irq,
- .timer = &spear3xx_timer,
- .init_machine = spear300_evb_init,
- .restart = spear_restart,
-MACHINE_END
diff --git a/arch/arm/mach-spear3xx/spear310.c b/arch/arm/mach-spear3xx/spear310.c
index febaa6f..b26e415 100644
--- a/arch/arm/mach-spear3xx/spear310.c
+++ b/arch/arm/mach-spear3xx/spear310.c
@@ -3,19 +3,84 @@
*
* SPEAr310 machine source file
*
- * Copyright (C) 2009 ST Microelectronics
- * Viresh Kumar<viresh.kumar@st.com>
+ * Copyright (C) 2009-2012 ST Microelectronics
+ * Viresh Kumar <viresh.kumar@st.com>
*
* This file is licensed under the terms of the GNU General Public
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
-#include <linux/ptrace.h>
-#include <asm/irq.h>
+#define pr_fmt(fmt) "SPEAr310: " fmt
+
+#include <linux/amba/pl08x.h>
+#include <linux/amba/serial.h>
+#include <linux/of_platform.h>
+#include <asm/hardware/vic.h>
+#include <asm/mach/arch.h>
#include <plat/shirq.h>
#include <mach/generic.h>
-#include <mach/hardware.h>
+#include <mach/spear.h>
+
+#define SPEAR310_UART1_BASE UL(0xB2000000)
+#define SPEAR310_UART2_BASE UL(0xB2080000)
+#define SPEAR310_UART3_BASE UL(0xB2100000)
+#define SPEAR310_UART4_BASE UL(0xB2180000)
+#define SPEAR310_UART5_BASE UL(0xB2200000)
+#define SPEAR310_SOC_CONFIG_BASE UL(0xB4000000)
+
+/* Interrupt registers offsets and masks */
+#define SPEAR310_INT_STS_MASK_REG 0x04
+#define SPEAR310_SMII0_IRQ_MASK (1 << 0)
+#define SPEAR310_SMII1_IRQ_MASK (1 << 1)
+#define SPEAR310_SMII2_IRQ_MASK (1 << 2)
+#define SPEAR310_SMII3_IRQ_MASK (1 << 3)
+#define SPEAR310_WAKEUP_SMII0_IRQ_MASK (1 << 4)
+#define SPEAR310_WAKEUP_SMII1_IRQ_MASK (1 << 5)
+#define SPEAR310_WAKEUP_SMII2_IRQ_MASK (1 << 6)
+#define SPEAR310_WAKEUP_SMII3_IRQ_MASK (1 << 7)
+#define SPEAR310_UART1_IRQ_MASK (1 << 8)
+#define SPEAR310_UART2_IRQ_MASK (1 << 9)
+#define SPEAR310_UART3_IRQ_MASK (1 << 10)
+#define SPEAR310_UART4_IRQ_MASK (1 << 11)
+#define SPEAR310_UART5_IRQ_MASK (1 << 12)
+#define SPEAR310_EMI_IRQ_MASK (1 << 13)
+#define SPEAR310_TDM_HDLC_IRQ_MASK (1 << 14)
+#define SPEAR310_RS485_0_IRQ_MASK (1 << 15)
+#define SPEAR310_RS485_1_IRQ_MASK (1 << 16)
+
+#define SPEAR310_SHIRQ_RAS1_MASK 0x000FF
+#define SPEAR310_SHIRQ_RAS2_MASK 0x01F00
+#define SPEAR310_SHIRQ_RAS3_MASK 0x02000
+#define SPEAR310_SHIRQ_INTRCOMM_RAS_MASK 0x1C000
+
+/* SPEAr310 Virtual irq definitions */
+/* IRQs sharing IRQ_GEN_RAS_1 */
+#define SPEAR310_VIRQ_SMII0 (SPEAR3XX_VIRQ_START + 0)
+#define SPEAR310_VIRQ_SMII1 (SPEAR3XX_VIRQ_START + 1)
+#define SPEAR310_VIRQ_SMII2 (SPEAR3XX_VIRQ_START + 2)
+#define SPEAR310_VIRQ_SMII3 (SPEAR3XX_VIRQ_START + 3)
+#define SPEAR310_VIRQ_WAKEUP_SMII0 (SPEAR3XX_VIRQ_START + 4)
+#define SPEAR310_VIRQ_WAKEUP_SMII1 (SPEAR3XX_VIRQ_START + 5)
+#define SPEAR310_VIRQ_WAKEUP_SMII2 (SPEAR3XX_VIRQ_START + 6)
+#define SPEAR310_VIRQ_WAKEUP_SMII3 (SPEAR3XX_VIRQ_START + 7)
+
+/* IRQs sharing IRQ_GEN_RAS_2 */
+#define SPEAR310_VIRQ_UART1 (SPEAR3XX_VIRQ_START + 8)
+#define SPEAR310_VIRQ_UART2 (SPEAR3XX_VIRQ_START + 9)
+#define SPEAR310_VIRQ_UART3 (SPEAR3XX_VIRQ_START + 10)
+#define SPEAR310_VIRQ_UART4 (SPEAR3XX_VIRQ_START + 11)
+#define SPEAR310_VIRQ_UART5 (SPEAR3XX_VIRQ_START + 12)
+
+/* IRQs sharing IRQ_GEN_RAS_3 */
+#define SPEAR310_VIRQ_EMI (SPEAR3XX_VIRQ_START + 13)
+#define SPEAR310_VIRQ_PLGPIO (SPEAR3XX_VIRQ_START + 14)
+
+/* IRQs sharing IRQ_INTRCOMM_RAS_ARM */
+#define SPEAR310_VIRQ_TDM_HDLC (SPEAR3XX_VIRQ_START + 15)
+#define SPEAR310_VIRQ_RS485_0 (SPEAR3XX_VIRQ_START + 16)
+#define SPEAR310_VIRQ_RS485_1 (SPEAR3XX_VIRQ_START + 17)
+
/* pad multiplexing support */
/* muxing registers */
@@ -255,17 +320,271 @@
},
};
-/* Add spear310 specific devices here */
+/* padmux devices to enable */
+static struct pmx_dev *spear310_evb_pmx_devs[] = {
+ /* spear3xx specific devices */
+ &spear3xx_pmx_i2c,
+ &spear3xx_pmx_ssp,
+ &spear3xx_pmx_gpio_pin0,
+ &spear3xx_pmx_gpio_pin1,
+ &spear3xx_pmx_gpio_pin2,
+ &spear3xx_pmx_gpio_pin3,
+ &spear3xx_pmx_gpio_pin4,
+ &spear3xx_pmx_gpio_pin5,
+ &spear3xx_pmx_uart0,
-/* spear310 routines */
-void __init spear310_init(struct pmx_mode *pmx_mode, struct pmx_dev **pmx_devs,
- u8 pmx_dev_count)
+ /* spear310 specific devices */
+ &spear310_pmx_emi_cs_0_1_4_5,
+ &spear310_pmx_emi_cs_2_3,
+ &spear310_pmx_uart1,
+ &spear310_pmx_uart2,
+ &spear310_pmx_uart3_4_5,
+ &spear310_pmx_fsmc,
+ &spear310_pmx_rs485_0_1,
+ &spear310_pmx_tdm0,
+};
+
+/* DMAC platform data's slave info */
+struct pl08x_channel_data spear310_dma_info[] = {
+ {
+ .bus_id = "uart0_rx",
+ .min_signal = 2,
+ .max_signal = 2,
+ .muxval = 0,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "uart0_tx",
+ .min_signal = 3,
+ .max_signal = 3,
+ .muxval = 0,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "ssp0_rx",
+ .min_signal = 8,
+ .max_signal = 8,
+ .muxval = 0,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "ssp0_tx",
+ .min_signal = 9,
+ .max_signal = 9,
+ .muxval = 0,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "i2c_rx",
+ .min_signal = 10,
+ .max_signal = 10,
+ .muxval = 0,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "i2c_tx",
+ .min_signal = 11,
+ .max_signal = 11,
+ .muxval = 0,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "irda",
+ .min_signal = 12,
+ .max_signal = 12,
+ .muxval = 0,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "adc",
+ .min_signal = 13,
+ .max_signal = 13,
+ .muxval = 0,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "to_jpeg",
+ .min_signal = 14,
+ .max_signal = 14,
+ .muxval = 0,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "from_jpeg",
+ .min_signal = 15,
+ .max_signal = 15,
+ .muxval = 0,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "uart1_rx",
+ .min_signal = 0,
+ .max_signal = 0,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "uart1_tx",
+ .min_signal = 1,
+ .max_signal = 1,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "uart2_rx",
+ .min_signal = 2,
+ .max_signal = 2,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "uart2_tx",
+ .min_signal = 3,
+ .max_signal = 3,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "uart3_rx",
+ .min_signal = 4,
+ .max_signal = 4,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "uart3_tx",
+ .min_signal = 5,
+ .max_signal = 5,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "uart4_rx",
+ .min_signal = 6,
+ .max_signal = 6,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "uart4_tx",
+ .min_signal = 7,
+ .max_signal = 7,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "uart5_rx",
+ .min_signal = 8,
+ .max_signal = 8,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "uart5_tx",
+ .min_signal = 9,
+ .max_signal = 9,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "ras5_rx",
+ .min_signal = 10,
+ .max_signal = 10,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "ras5_tx",
+ .min_signal = 11,
+ .max_signal = 11,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "ras6_rx",
+ .min_signal = 12,
+ .max_signal = 12,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "ras6_tx",
+ .min_signal = 13,
+ .max_signal = 13,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "ras7_rx",
+ .min_signal = 14,
+ .max_signal = 14,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "ras7_tx",
+ .min_signal = 15,
+ .max_signal = 15,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ },
+};
+
+/* uart devices plat data */
+static struct amba_pl011_data spear310_uart_data[] = {
+ {
+ .dma_filter = pl08x_filter_id,
+ .dma_tx_param = "uart1_tx",
+ .dma_rx_param = "uart1_rx",
+ }, {
+ .dma_filter = pl08x_filter_id,
+ .dma_tx_param = "uart2_tx",
+ .dma_rx_param = "uart2_rx",
+ }, {
+ .dma_filter = pl08x_filter_id,
+ .dma_tx_param = "uart3_tx",
+ .dma_rx_param = "uart3_rx",
+ }, {
+ .dma_filter = pl08x_filter_id,
+ .dma_tx_param = "uart4_tx",
+ .dma_rx_param = "uart4_rx",
+ }, {
+ .dma_filter = pl08x_filter_id,
+ .dma_tx_param = "uart5_tx",
+ .dma_rx_param = "uart5_rx",
+ },
+};
+
+/* Add SPEAr310 auxdata to pass platform data */
+static struct of_dev_auxdata spear310_auxdata_lookup[] __initdata = {
+ OF_DEV_AUXDATA("arm,pl022", SPEAR3XX_ICM1_SSP_BASE, NULL,
+ &pl022_plat_data),
+ OF_DEV_AUXDATA("arm,pl080", SPEAR3XX_ICM3_DMA_BASE, NULL,
+ &pl080_plat_data),
+ OF_DEV_AUXDATA("arm,pl011", SPEAR310_UART1_BASE, NULL,
+ &spear310_uart_data[0]),
+ OF_DEV_AUXDATA("arm,pl011", SPEAR310_UART2_BASE, NULL,
+ &spear310_uart_data[1]),
+ OF_DEV_AUXDATA("arm,pl011", SPEAR310_UART3_BASE, NULL,
+ &spear310_uart_data[2]),
+ OF_DEV_AUXDATA("arm,pl011", SPEAR310_UART4_BASE, NULL,
+ &spear310_uart_data[3]),
+ OF_DEV_AUXDATA("arm,pl011", SPEAR310_UART5_BASE, NULL,
+ &spear310_uart_data[4]),
+ {}
+};
+
+static void __init spear310_dt_init(void)
{
void __iomem *base;
int ret = 0;
- /* call spear3xx family common init function */
- spear3xx_init();
+ pl080_plat_data.slave_channels = spear310_dma_info;
+ pl080_plat_data.num_slave_channels = ARRAY_SIZE(spear310_dma_info);
+
+ of_platform_populate(NULL, of_default_bus_match_table,
+ spear310_auxdata_lookup, NULL);
/* shared irq registration */
base = ioremap(SPEAR310_SOC_CONFIG_BASE, SZ_4K);
@@ -274,35 +593,59 @@
shirq_ras1.regs.base = base;
ret = spear_shirq_register(&shirq_ras1);
if (ret)
- printk(KERN_ERR "Error registering Shared IRQ 1\n");
+ pr_err("Error registering Shared IRQ 1\n");
/* shirq 2 */
shirq_ras2.regs.base = base;
ret = spear_shirq_register(&shirq_ras2);
if (ret)
- printk(KERN_ERR "Error registering Shared IRQ 2\n");
+ pr_err("Error registering Shared IRQ 2\n");
/* shirq 3 */
shirq_ras3.regs.base = base;
ret = spear_shirq_register(&shirq_ras3);
if (ret)
- printk(KERN_ERR "Error registering Shared IRQ 3\n");
+ pr_err("Error registering Shared IRQ 3\n");
/* shirq 4 */
shirq_intrcomm_ras.regs.base = base;
ret = spear_shirq_register(&shirq_intrcomm_ras);
if (ret)
- printk(KERN_ERR "Error registering Shared IRQ 4\n");
+ pr_err("Error registering Shared IRQ 4\n");
}
- /* pmx initialization */
- pmx_driver.base = base;
- pmx_driver.mode = pmx_mode;
- pmx_driver.devs = pmx_devs;
- pmx_driver.devs_count = pmx_dev_count;
+ if (of_machine_is_compatible("st,spear310-evb")) {
+ /* pmx initialization */
+ pmx_driver.base = base;
+ pmx_driver.mode = NULL;
+ pmx_driver.devs = spear310_evb_pmx_devs;
+ pmx_driver.devs_count = ARRAY_SIZE(spear310_evb_pmx_devs);
- ret = pmx_register(&pmx_driver);
- if (ret)
- printk(KERN_ERR "padmux: registration failed. err no: %d\n",
- ret);
+ ret = pmx_register(&pmx_driver);
+ if (ret)
+ pr_err("padmux: registration failed. err no: %d\n",
+ ret);
+ }
}
+
+static const char * const spear310_dt_board_compat[] = {
+ "st,spear310",
+ "st,spear310-evb",
+ NULL,
+};
+
+static void __init spear310_map_io(void)
+{
+ spear3xx_map_io();
+ spear310_clk_init();
+}
+
+DT_MACHINE_START(SPEAR310_DT, "ST SPEAr310 SoC with Flattened Device Tree")
+ .map_io = spear310_map_io,
+ .init_irq = spear3xx_dt_init_irq,
+ .handle_irq = vic_handle_irq,
+ .timer = &spear3xx_timer,
+ .init_machine = spear310_dt_init,
+ .restart = spear_restart,
+ .dt_compat = spear310_dt_board_compat,
+MACHINE_END
diff --git a/arch/arm/mach-spear3xx/spear310_evb.c b/arch/arm/mach-spear3xx/spear310_evb.c
deleted file mode 100644
index f92c499..0000000
--- a/arch/arm/mach-spear3xx/spear310_evb.c
+++ /dev/null
@@ -1,81 +0,0 @@
-/*
- * arch/arm/mach-spear3xx/spear310_evb.c
- *
- * SPEAr310 evaluation board source file
- *
- * Copyright (C) 2009 ST Microelectronics
- * Viresh Kumar<viresh.kumar@st.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <asm/hardware/vic.h>
-#include <asm/mach/arch.h>
-#include <asm/mach-types.h>
-#include <mach/generic.h>
-#include <mach/hardware.h>
-
-/* padmux devices to enable */
-static struct pmx_dev *pmx_devs[] = {
- /* spear3xx specific devices */
- &spear3xx_pmx_i2c,
- &spear3xx_pmx_ssp,
- &spear3xx_pmx_gpio_pin0,
- &spear3xx_pmx_gpio_pin1,
- &spear3xx_pmx_gpio_pin2,
- &spear3xx_pmx_gpio_pin3,
- &spear3xx_pmx_gpio_pin4,
- &spear3xx_pmx_gpio_pin5,
- &spear3xx_pmx_uart0,
-
- /* spear310 specific devices */
- &spear310_pmx_emi_cs_0_1_4_5,
- &spear310_pmx_emi_cs_2_3,
- &spear310_pmx_uart1,
- &spear310_pmx_uart2,
- &spear310_pmx_uart3_4_5,
- &spear310_pmx_fsmc,
- &spear310_pmx_rs485_0_1,
- &spear310_pmx_tdm0,
-};
-
-static struct amba_device *amba_devs[] __initdata = {
- /* spear3xx specific devices */
- &spear3xx_gpio_device,
- &spear3xx_uart_device,
-
- /* spear310 specific devices */
-};
-
-static struct platform_device *plat_devs[] __initdata = {
- /* spear3xx specific devices */
-
- /* spear310 specific devices */
-};
-
-static void __init spear310_evb_init(void)
-{
- unsigned int i;
-
- /* call spear310 machine init function */
- spear310_init(NULL, pmx_devs, ARRAY_SIZE(pmx_devs));
-
- /* Add Platform Devices */
- platform_add_devices(plat_devs, ARRAY_SIZE(plat_devs));
-
- /* Add Amba Devices */
- for (i = 0; i < ARRAY_SIZE(amba_devs); i++)
- amba_device_register(amba_devs[i], &iomem_resource);
-}
-
-MACHINE_START(SPEAR310, "ST-SPEAR310-EVB")
- .atag_offset = 0x100,
- .map_io = spear3xx_map_io,
- .init_irq = spear3xx_init_irq,
- .handle_irq = vic_handle_irq,
- .timer = &spear3xx_timer,
- .init_machine = spear310_evb_init,
- .restart = spear_restart,
-MACHINE_END
diff --git a/arch/arm/mach-spear3xx/spear320.c b/arch/arm/mach-spear3xx/spear320.c
index deaaf19..2f5979b 100644
--- a/arch/arm/mach-spear3xx/spear320.c
+++ b/arch/arm/mach-spear3xx/spear320.c
@@ -3,19 +3,85 @@
*
* SPEAr320 machine source file
*
- * Copyright (C) 2009 ST Microelectronics
- * Viresh Kumar<viresh.kumar@st.com>
+ * Copyright (C) 2009-2012 ST Microelectronics
+ * Viresh Kumar <viresh.kumar@st.com>
*
* This file is licensed under the terms of the GNU General Public
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
-#include <linux/ptrace.h>
-#include <asm/irq.h>
+#define pr_fmt(fmt) "SPEAr320: " fmt
+
+#include <linux/amba/pl022.h>
+#include <linux/amba/pl08x.h>
+#include <linux/amba/serial.h>
+#include <linux/of_platform.h>
+#include <asm/hardware/vic.h>
+#include <asm/mach/arch.h>
#include <plat/shirq.h>
#include <mach/generic.h>
-#include <mach/hardware.h>
+#include <mach/spear.h>
+
+#define SPEAR320_UART1_BASE UL(0xA3000000)
+#define SPEAR320_UART2_BASE UL(0xA4000000)
+#define SPEAR320_SSP0_BASE UL(0xA5000000)
+#define SPEAR320_SSP1_BASE UL(0xA6000000)
+#define SPEAR320_SOC_CONFIG_BASE UL(0xB3000000)
+
+/* Interrupt registers offsets and masks */
+#define SPEAR320_INT_STS_MASK_REG 0x04
+#define SPEAR320_INT_CLR_MASK_REG 0x04
+#define SPEAR320_INT_ENB_MASK_REG 0x08
+#define SPEAR320_GPIO_IRQ_MASK (1 << 0)
+#define SPEAR320_I2S_PLAY_IRQ_MASK (1 << 1)
+#define SPEAR320_I2S_REC_IRQ_MASK (1 << 2)
+#define SPEAR320_EMI_IRQ_MASK (1 << 7)
+#define SPEAR320_CLCD_IRQ_MASK (1 << 8)
+#define SPEAR320_SPP_IRQ_MASK (1 << 9)
+#define SPEAR320_SDHCI_IRQ_MASK (1 << 10)
+#define SPEAR320_CAN_U_IRQ_MASK (1 << 11)
+#define SPEAR320_CAN_L_IRQ_MASK (1 << 12)
+#define SPEAR320_UART1_IRQ_MASK (1 << 13)
+#define SPEAR320_UART2_IRQ_MASK (1 << 14)
+#define SPEAR320_SSP1_IRQ_MASK (1 << 15)
+#define SPEAR320_SSP2_IRQ_MASK (1 << 16)
+#define SPEAR320_SMII0_IRQ_MASK (1 << 17)
+#define SPEAR320_MII1_SMII1_IRQ_MASK (1 << 18)
+#define SPEAR320_WAKEUP_SMII0_IRQ_MASK (1 << 19)
+#define SPEAR320_WAKEUP_MII1_SMII1_IRQ_MASK (1 << 20)
+#define SPEAR320_I2C1_IRQ_MASK (1 << 21)
+
+#define SPEAR320_SHIRQ_RAS1_MASK 0x000380
+#define SPEAR320_SHIRQ_RAS3_MASK 0x000007
+#define SPEAR320_SHIRQ_INTRCOMM_RAS_MASK 0x3FF800
+
+/* SPEAr320 Virtual irq definitions */
+/* IRQs sharing IRQ_GEN_RAS_1 */
+#define SPEAR320_VIRQ_EMI (SPEAR3XX_VIRQ_START + 0)
+#define SPEAR320_VIRQ_CLCD (SPEAR3XX_VIRQ_START + 1)
+#define SPEAR320_VIRQ_SPP (SPEAR3XX_VIRQ_START + 2)
+
+/* IRQs sharing IRQ_GEN_RAS_2 */
+#define SPEAR320_IRQ_SDHCI SPEAR3XX_IRQ_GEN_RAS_2
+
+/* IRQs sharing IRQ_GEN_RAS_3 */
+#define SPEAR320_VIRQ_PLGPIO (SPEAR3XX_VIRQ_START + 3)
+#define SPEAR320_VIRQ_I2S_PLAY (SPEAR3XX_VIRQ_START + 4)
+#define SPEAR320_VIRQ_I2S_REC (SPEAR3XX_VIRQ_START + 5)
+
+/* IRQs sharing IRQ_INTRCOMM_RAS_ARM */
+#define SPEAR320_VIRQ_CANU (SPEAR3XX_VIRQ_START + 6)
+#define SPEAR320_VIRQ_CANL (SPEAR3XX_VIRQ_START + 7)
+#define SPEAR320_VIRQ_UART1 (SPEAR3XX_VIRQ_START + 8)
+#define SPEAR320_VIRQ_UART2 (SPEAR3XX_VIRQ_START + 9)
+#define SPEAR320_VIRQ_SSP1 (SPEAR3XX_VIRQ_START + 10)
+#define SPEAR320_VIRQ_SSP2 (SPEAR3XX_VIRQ_START + 11)
+#define SPEAR320_VIRQ_SMII0 (SPEAR3XX_VIRQ_START + 12)
+#define SPEAR320_VIRQ_MII1_SMII1 (SPEAR3XX_VIRQ_START + 13)
+#define SPEAR320_VIRQ_WAKEUP_SMII0 (SPEAR3XX_VIRQ_START + 14)
+#define SPEAR320_VIRQ_WAKEUP_MII1_SMII1 (SPEAR3XX_VIRQ_START + 15)
+#define SPEAR320_VIRQ_I2C1 (SPEAR3XX_VIRQ_START + 16)
/* pad multiplexing support */
/* muxing registers */
@@ -508,17 +574,271 @@
},
};
-/* Add spear320 specific devices here */
+/* padmux devices to enable */
+static struct pmx_dev *spear320_evb_pmx_devs[] = {
+ /* spear3xx specific devices */
+ &spear3xx_pmx_i2c,
+ &spear3xx_pmx_ssp,
+ &spear3xx_pmx_mii,
+ &spear3xx_pmx_uart0,
-/* spear320 routines */
-void __init spear320_init(struct pmx_mode *pmx_mode, struct pmx_dev **pmx_devs,
- u8 pmx_dev_count)
+ /* spear320 specific devices */
+ &spear320_pmx_fsmc,
+ &spear320_pmx_sdhci,
+ &spear320_pmx_i2s,
+ &spear320_pmx_uart1,
+ &spear320_pmx_uart2,
+ &spear320_pmx_can,
+ &spear320_pmx_pwm0,
+ &spear320_pmx_pwm1,
+ &spear320_pmx_pwm2,
+ &spear320_pmx_mii1,
+};
+
+/* DMAC platform data's slave info */
+struct pl08x_channel_data spear320_dma_info[] = {
+ {
+ .bus_id = "uart0_rx",
+ .min_signal = 2,
+ .max_signal = 2,
+ .muxval = 0,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "uart0_tx",
+ .min_signal = 3,
+ .max_signal = 3,
+ .muxval = 0,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "ssp0_rx",
+ .min_signal = 8,
+ .max_signal = 8,
+ .muxval = 0,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "ssp0_tx",
+ .min_signal = 9,
+ .max_signal = 9,
+ .muxval = 0,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "i2c0_rx",
+ .min_signal = 10,
+ .max_signal = 10,
+ .muxval = 0,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "i2c0_tx",
+ .min_signal = 11,
+ .max_signal = 11,
+ .muxval = 0,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "irda",
+ .min_signal = 12,
+ .max_signal = 12,
+ .muxval = 0,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "adc",
+ .min_signal = 13,
+ .max_signal = 13,
+ .muxval = 0,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "to_jpeg",
+ .min_signal = 14,
+ .max_signal = 14,
+ .muxval = 0,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "from_jpeg",
+ .min_signal = 15,
+ .max_signal = 15,
+ .muxval = 0,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "ssp1_rx",
+ .min_signal = 0,
+ .max_signal = 0,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB2,
+ }, {
+ .bus_id = "ssp1_tx",
+ .min_signal = 1,
+ .max_signal = 1,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB2,
+ }, {
+ .bus_id = "ssp2_rx",
+ .min_signal = 2,
+ .max_signal = 2,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB2,
+ }, {
+ .bus_id = "ssp2_tx",
+ .min_signal = 3,
+ .max_signal = 3,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB2,
+ }, {
+ .bus_id = "uart1_rx",
+ .min_signal = 4,
+ .max_signal = 4,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB2,
+ }, {
+ .bus_id = "uart1_tx",
+ .min_signal = 5,
+ .max_signal = 5,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB2,
+ }, {
+ .bus_id = "uart2_rx",
+ .min_signal = 6,
+ .max_signal = 6,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB2,
+ }, {
+ .bus_id = "uart2_tx",
+ .min_signal = 7,
+ .max_signal = 7,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB2,
+ }, {
+ .bus_id = "i2c1_rx",
+ .min_signal = 8,
+ .max_signal = 8,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB2,
+ }, {
+ .bus_id = "i2c1_tx",
+ .min_signal = 9,
+ .max_signal = 9,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB2,
+ }, {
+ .bus_id = "i2c2_rx",
+ .min_signal = 10,
+ .max_signal = 10,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB2,
+ }, {
+ .bus_id = "i2c2_tx",
+ .min_signal = 11,
+ .max_signal = 11,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB2,
+ }, {
+ .bus_id = "i2s_rx",
+ .min_signal = 12,
+ .max_signal = 12,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB2,
+ }, {
+ .bus_id = "i2s_tx",
+ .min_signal = 13,
+ .max_signal = 13,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB2,
+ }, {
+ .bus_id = "rs485_rx",
+ .min_signal = 14,
+ .max_signal = 14,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB2,
+ }, {
+ .bus_id = "rs485_tx",
+ .min_signal = 15,
+ .max_signal = 15,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB2,
+ },
+};
+
+static struct pl022_ssp_controller spear320_ssp_data[] = {
+ {
+ .bus_id = 1,
+ .enable_dma = 1,
+ .dma_filter = pl08x_filter_id,
+ .dma_tx_param = "ssp1_tx",
+ .dma_rx_param = "ssp1_rx",
+ .num_chipselect = 2,
+ }, {
+ .bus_id = 2,
+ .enable_dma = 1,
+ .dma_filter = pl08x_filter_id,
+ .dma_tx_param = "ssp2_tx",
+ .dma_rx_param = "ssp2_rx",
+ .num_chipselect = 2,
+ }
+};
+
+static struct amba_pl011_data spear320_uart_data[] = {
+ {
+ .dma_filter = pl08x_filter_id,
+ .dma_tx_param = "uart1_tx",
+ .dma_rx_param = "uart1_rx",
+ }, {
+ .dma_filter = pl08x_filter_id,
+ .dma_tx_param = "uart2_tx",
+ .dma_rx_param = "uart2_rx",
+ },
+};
+
+/* Add SPEAr310 auxdata to pass platform data */
+static struct of_dev_auxdata spear320_auxdata_lookup[] __initdata = {
+ OF_DEV_AUXDATA("arm,pl022", SPEAR3XX_ICM1_SSP_BASE, NULL,
+ &pl022_plat_data),
+ OF_DEV_AUXDATA("arm,pl080", SPEAR3XX_ICM3_DMA_BASE, NULL,
+ &pl080_plat_data),
+ OF_DEV_AUXDATA("arm,pl022", SPEAR320_SSP0_BASE, NULL,
+ &spear320_ssp_data[0]),
+ OF_DEV_AUXDATA("arm,pl022", SPEAR320_SSP1_BASE, NULL,
+ &spear320_ssp_data[1]),
+ OF_DEV_AUXDATA("arm,pl011", SPEAR320_UART1_BASE, NULL,
+ &spear320_uart_data[0]),
+ OF_DEV_AUXDATA("arm,pl011", SPEAR320_UART2_BASE, NULL,
+ &spear320_uart_data[1]),
+ {}
+};
+
+static void __init spear320_dt_init(void)
{
void __iomem *base;
int ret = 0;
- /* call spear3xx family common init function */
- spear3xx_init();
+ pl080_plat_data.slave_channels = spear320_dma_info;
+ pl080_plat_data.num_slave_channels = ARRAY_SIZE(spear320_dma_info);
+
+ of_platform_populate(NULL, of_default_bus_match_table,
+ spear320_auxdata_lookup, NULL);
/* shared irq registration */
base = ioremap(SPEAR320_SOC_CONFIG_BASE, SZ_4K);
@@ -527,29 +847,53 @@
shirq_ras1.regs.base = base;
ret = spear_shirq_register(&shirq_ras1);
if (ret)
- printk(KERN_ERR "Error registering Shared IRQ 1\n");
+ pr_err("Error registering Shared IRQ 1\n");
/* shirq 3 */
shirq_ras3.regs.base = base;
ret = spear_shirq_register(&shirq_ras3);
if (ret)
- printk(KERN_ERR "Error registering Shared IRQ 3\n");
+ pr_err("Error registering Shared IRQ 3\n");
/* shirq 4 */
shirq_intrcomm_ras.regs.base = base;
ret = spear_shirq_register(&shirq_intrcomm_ras);
if (ret)
- printk(KERN_ERR "Error registering Shared IRQ 4\n");
+ pr_err("Error registering Shared IRQ 4\n");
}
- /* pmx initialization */
- pmx_driver.base = base;
- pmx_driver.mode = pmx_mode;
- pmx_driver.devs = pmx_devs;
- pmx_driver.devs_count = pmx_dev_count;
+ if (of_machine_is_compatible("st,spear320-evb")) {
+ /* pmx initialization */
+ pmx_driver.base = base;
+ pmx_driver.mode = &spear320_auto_net_mii_mode;
+ pmx_driver.devs = spear320_evb_pmx_devs;
+ pmx_driver.devs_count = ARRAY_SIZE(spear320_evb_pmx_devs);
- ret = pmx_register(&pmx_driver);
- if (ret)
- printk(KERN_ERR "padmux: registration failed. err no: %d\n",
- ret);
+ ret = pmx_register(&pmx_driver);
+ if (ret)
+ pr_err("padmux: registration failed. err no: %d\n",
+ ret);
+ }
}
+
+static const char * const spear320_dt_board_compat[] = {
+ "st,spear320",
+ "st,spear320-evb",
+ NULL,
+};
+
+static void __init spear320_map_io(void)
+{
+ spear3xx_map_io();
+ spear320_clk_init();
+}
+
+DT_MACHINE_START(SPEAR320_DT, "ST SPEAr320 SoC with Flattened Device Tree")
+ .map_io = spear320_map_io,
+ .init_irq = spear3xx_dt_init_irq,
+ .handle_irq = vic_handle_irq,
+ .timer = &spear3xx_timer,
+ .init_machine = spear320_dt_init,
+ .restart = spear_restart,
+ .dt_compat = spear320_dt_board_compat,
+MACHINE_END
diff --git a/arch/arm/mach-spear3xx/spear320_evb.c b/arch/arm/mach-spear3xx/spear320_evb.c
deleted file mode 100644
index 105334a..0000000
--- a/arch/arm/mach-spear3xx/spear320_evb.c
+++ /dev/null
@@ -1,79 +0,0 @@
-/*
- * arch/arm/mach-spear3xx/spear320_evb.c
- *
- * SPEAr320 evaluation board source file
- *
- * Copyright (C) 2009 ST Microelectronics
- * Viresh Kumar<viresh.kumar@st.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <asm/hardware/vic.h>
-#include <asm/mach/arch.h>
-#include <asm/mach-types.h>
-#include <mach/generic.h>
-#include <mach/hardware.h>
-
-/* padmux devices to enable */
-static struct pmx_dev *pmx_devs[] = {
- /* spear3xx specific devices */
- &spear3xx_pmx_i2c,
- &spear3xx_pmx_ssp,
- &spear3xx_pmx_mii,
- &spear3xx_pmx_uart0,
-
- /* spear320 specific devices */
- &spear320_pmx_fsmc,
- &spear320_pmx_sdhci,
- &spear320_pmx_i2s,
- &spear320_pmx_uart1,
- &spear320_pmx_uart2,
- &spear320_pmx_can,
- &spear320_pmx_pwm0,
- &spear320_pmx_pwm1,
- &spear320_pmx_pwm2,
- &spear320_pmx_mii1,
-};
-
-static struct amba_device *amba_devs[] __initdata = {
- /* spear3xx specific devices */
- &spear3xx_gpio_device,
- &spear3xx_uart_device,
-
- /* spear320 specific devices */
-};
-
-static struct platform_device *plat_devs[] __initdata = {
- /* spear3xx specific devices */
-
- /* spear320 specific devices */
-};
-
-static void __init spear320_evb_init(void)
-{
- unsigned int i;
-
- /* call spear320 machine init function */
- spear320_init(&spear320_auto_net_mii_mode, pmx_devs,
- ARRAY_SIZE(pmx_devs));
-
- /* Add Platform Devices */
- platform_add_devices(plat_devs, ARRAY_SIZE(plat_devs));
-
- /* Add Amba Devices */
- for (i = 0; i < ARRAY_SIZE(amba_devs); i++)
- amba_device_register(amba_devs[i], &iomem_resource);
-}
-
-MACHINE_START(SPEAR320, "ST-SPEAR320-EVB")
- .atag_offset = 0x100,
- .map_io = spear3xx_map_io,
- .init_irq = spear3xx_init_irq,
- .handle_irq = vic_handle_irq,
- .timer = &spear3xx_timer,
- .init_machine = spear320_evb_init,
- .restart = spear_restart,
-MACHINE_END
diff --git a/arch/arm/mach-spear3xx/spear3xx.c b/arch/arm/mach-spear3xx/spear3xx.c
index b1733c3..bbb11ef 100644
--- a/arch/arm/mach-spear3xx/spear3xx.c
+++ b/arch/arm/mach-spear3xx/spear3xx.c
@@ -3,83 +3,25 @@
*
* SPEAr3XX machines common source file
*
- * Copyright (C) 2009 ST Microelectronics
- * Viresh Kumar<viresh.kumar@st.com>
+ * Copyright (C) 2009-2012 ST Microelectronics
+ * Viresh Kumar <viresh.kumar@st.com>
*
* This file is licensed under the terms of the GNU General Public
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
-#include <linux/types.h>
-#include <linux/amba/pl061.h>
-#include <linux/ptrace.h>
+#define pr_fmt(fmt) "SPEAr3xx: " fmt
+
+#include <linux/amba/pl022.h>
+#include <linux/amba/pl08x.h>
+#include <linux/of_irq.h>
#include <linux/io.h>
+#include <asm/hardware/pl080.h>
#include <asm/hardware/vic.h>
-#include <asm/irq.h>
-#include <asm/mach/arch.h>
+#include <plat/pl080.h>
#include <mach/generic.h>
-#include <mach/hardware.h>
-
-/* Add spear3xx machines common devices here */
-/* gpio device registration */
-static struct pl061_platform_data gpio_plat_data = {
- .gpio_base = 0,
- .irq_base = SPEAR3XX_GPIO_INT_BASE,
-};
-
-AMBA_APB_DEVICE(spear3xx_gpio, "gpio", 0, SPEAR3XX_ICM3_GPIO_BASE,
- {SPEAR3XX_IRQ_BASIC_GPIO}, &gpio_plat_data);
-
-/* uart device registration */
-AMBA_APB_DEVICE(spear3xx_uart, "uart", 0, SPEAR3XX_ICM1_UART_BASE,
- {SPEAR3XX_IRQ_UART}, NULL);
-
-/* Do spear3xx familiy common initialization part here */
-void __init spear3xx_init(void)
-{
- /* nothing to do for now */
-}
-
-/* This will initialize vic */
-void __init spear3xx_init_irq(void)
-{
- vic_init((void __iomem *)VA_SPEAR3XX_ML1_VIC_BASE, 0, ~0, 0);
-}
-
-/* Following will create static virtual/physical mappings */
-struct map_desc spear3xx_io_desc[] __initdata = {
- {
- .virtual = VA_SPEAR3XX_ICM1_UART_BASE,
- .pfn = __phys_to_pfn(SPEAR3XX_ICM1_UART_BASE),
- .length = SZ_4K,
- .type = MT_DEVICE
- }, {
- .virtual = VA_SPEAR3XX_ML1_VIC_BASE,
- .pfn = __phys_to_pfn(SPEAR3XX_ML1_VIC_BASE),
- .length = SZ_4K,
- .type = MT_DEVICE
- }, {
- .virtual = VA_SPEAR3XX_ICM3_SYS_CTRL_BASE,
- .pfn = __phys_to_pfn(SPEAR3XX_ICM3_SYS_CTRL_BASE),
- .length = SZ_4K,
- .type = MT_DEVICE
- }, {
- .virtual = VA_SPEAR3XX_ICM3_MISC_REG_BASE,
- .pfn = __phys_to_pfn(SPEAR3XX_ICM3_MISC_REG_BASE),
- .length = SZ_4K,
- .type = MT_DEVICE
- },
-};
-
-/* This will create static memory mapping for selected devices */
-void __init spear3xx_map_io(void)
-{
- iotable_init(spear3xx_io_desc, ARRAY_SIZE(spear3xx_io_desc));
-
- /* This will initialize clock framework */
- spear3xx_clk_init();
-}
+#include <mach/spear.h>
/* pad multiplexing support */
/* devices */
@@ -506,6 +448,68 @@
};
#endif /* CONFIG_MACH_SPEAR310 || CONFIG_MACH_SPEAR320 */
+/* ssp device registration */
+struct pl022_ssp_controller pl022_plat_data = {
+ .bus_id = 0,
+ .enable_dma = 1,
+ .dma_filter = pl08x_filter_id,
+ .dma_tx_param = "ssp0_tx",
+ .dma_rx_param = "ssp0_rx",
+ /*
+ * This is number of spi devices that can be connected to spi. There are
+ * two type of chipselects on which slave devices can work. One is chip
+ * select provided by spi masters other is controlled through external
+ * gpio's. We can't use chipselect provided from spi master (because as
+ * soon as FIFO becomes empty, CS is disabled and transfer ends). So
+ * this number now depends on number of gpios available for spi. each
+ * slave on each master requires a separate gpio pin.
+ */
+ .num_chipselect = 2,
+};
+
+/* dmac device registration */
+struct pl08x_platform_data pl080_plat_data = {
+ .memcpy_channel = {
+ .bus_id = "memcpy",
+ .cctl = (PL080_BSIZE_16 << PL080_CONTROL_SB_SIZE_SHIFT | \
+ PL080_BSIZE_16 << PL080_CONTROL_DB_SIZE_SHIFT | \
+ PL080_WIDTH_32BIT << PL080_CONTROL_SWIDTH_SHIFT | \
+ PL080_WIDTH_32BIT << PL080_CONTROL_DWIDTH_SHIFT | \
+ PL080_CONTROL_PROT_BUFF | PL080_CONTROL_PROT_CACHE | \
+ PL080_CONTROL_PROT_SYS),
+ },
+ .lli_buses = PL08X_AHB1,
+ .mem_buses = PL08X_AHB1,
+ .get_signal = pl080_get_signal,
+ .put_signal = pl080_put_signal,
+};
+
+/*
+ * Following will create 16MB static virtual/physical mappings
+ * PHYSICAL VIRTUAL
+ * 0xD0000000 0xFD000000
+ * 0xFC000000 0xFC000000
+ */
+struct map_desc spear3xx_io_desc[] __initdata = {
+ {
+ .virtual = VA_SPEAR3XX_ICM1_2_BASE,
+ .pfn = __phys_to_pfn(SPEAR3XX_ICM1_2_BASE),
+ .length = SZ_16M,
+ .type = MT_DEVICE
+ }, {
+ .virtual = VA_SPEAR3XX_ICM3_SMI_CTRL_BASE,
+ .pfn = __phys_to_pfn(SPEAR3XX_ICM3_SMI_CTRL_BASE),
+ .length = SZ_16M,
+ .type = MT_DEVICE
+ },
+};
+
+/* This will create static memory mapping for selected devices */
+void __init spear3xx_map_io(void)
+{
+ iotable_init(spear3xx_io_desc, ARRAY_SIZE(spear3xx_io_desc));
+}
+
static void __init spear3xx_timer_init(void)
{
char pclk_name[] = "pll3_48m_clk";
@@ -530,9 +534,19 @@
clk_put(gpt_clk);
clk_put(pclk);
- spear_setup_timer();
+ spear_setup_timer(SPEAR3XX_CPU_TMR_BASE, SPEAR3XX_IRQ_CPU_GPT1_1);
}
struct sys_timer spear3xx_timer = {
.init = spear3xx_timer_init,
};
+
+static const struct of_device_id vic_of_match[] __initconst = {
+ { .compatible = "arm,pl190-vic", .data = vic_of_init, },
+ { /* Sentinel */ }
+};
+
+void __init spear3xx_dt_init_irq(void)
+{
+ of_irq_init(vic_of_match);
+}
diff --git a/arch/arm/mach-spear6xx/Makefile.boot b/arch/arm/mach-spear6xx/Makefile.boot
index 4674a4c..af493da 100644
--- a/arch/arm/mach-spear6xx/Makefile.boot
+++ b/arch/arm/mach-spear6xx/Makefile.boot
@@ -1,3 +1,5 @@
zreladdr-y += 0x00008000
params_phys-y := 0x00000100
initrd_phys-y := 0x00800000
+
+dtb-$(CONFIG_BOARD_SPEAR600_DT) += spear600-evb.dtb
diff --git a/arch/arm/mach-spear6xx/clock.c b/arch/arm/mach-spear6xx/clock.c
index a86499a..bef77d4 100644
--- a/arch/arm/mach-spear6xx/clock.c
+++ b/arch/arm/mach-spear6xx/clock.c
@@ -16,6 +16,112 @@
#include <linux/kernel.h>
#include <plat/clock.h>
#include <mach/misc_regs.h>
+#include <mach/spear.h>
+
+#define PLL1_CTR (MISC_BASE + 0x008)
+#define PLL1_FRQ (MISC_BASE + 0x00C)
+#define PLL1_MOD (MISC_BASE + 0x010)
+#define PLL2_CTR (MISC_BASE + 0x014)
+/* PLL_CTR register masks */
+#define PLL_ENABLE 2
+#define PLL_MODE_SHIFT 4
+#define PLL_MODE_MASK 0x3
+#define PLL_MODE_NORMAL 0
+#define PLL_MODE_FRACTION 1
+#define PLL_MODE_DITH_DSB 2
+#define PLL_MODE_DITH_SSB 3
+
+#define PLL2_FRQ (MISC_BASE + 0x018)
+/* PLL FRQ register masks */
+#define PLL_DIV_N_SHIFT 0
+#define PLL_DIV_N_MASK 0xFF
+#define PLL_DIV_P_SHIFT 8
+#define PLL_DIV_P_MASK 0x7
+#define PLL_NORM_FDBK_M_SHIFT 24
+#define PLL_NORM_FDBK_M_MASK 0xFF
+#define PLL_DITH_FDBK_M_SHIFT 16
+#define PLL_DITH_FDBK_M_MASK 0xFFFF
+
+#define PLL2_MOD (MISC_BASE + 0x01C)
+#define PLL_CLK_CFG (MISC_BASE + 0x020)
+#define CORE_CLK_CFG (MISC_BASE + 0x024)
+/* CORE CLK CFG register masks */
+#define PLL_HCLK_RATIO_SHIFT 10
+#define PLL_HCLK_RATIO_MASK 0x3
+#define HCLK_PCLK_RATIO_SHIFT 8
+#define HCLK_PCLK_RATIO_MASK 0x3
+
+#define PERIP_CLK_CFG (MISC_BASE + 0x028)
+/* PERIP_CLK_CFG register masks */
+#define CLCD_CLK_SHIFT 2
+#define CLCD_CLK_MASK 0x3
+#define UART_CLK_SHIFT 4
+#define UART_CLK_MASK 0x1
+#define FIRDA_CLK_SHIFT 5
+#define FIRDA_CLK_MASK 0x3
+#define GPT0_CLK_SHIFT 8
+#define GPT1_CLK_SHIFT 10
+#define GPT2_CLK_SHIFT 11
+#define GPT3_CLK_SHIFT 12
+#define GPT_CLK_MASK 0x1
+#define AUX_CLK_PLL3_VAL 0
+#define AUX_CLK_PLL1_VAL 1
+
+#define PERIP1_CLK_ENB (MISC_BASE + 0x02C)
+/* PERIP1_CLK_ENB register masks */
+#define UART0_CLK_ENB 3
+#define UART1_CLK_ENB 4
+#define SSP0_CLK_ENB 5
+#define SSP1_CLK_ENB 6
+#define I2C_CLK_ENB 7
+#define JPEG_CLK_ENB 8
+#define FSMC_CLK_ENB 9
+#define FIRDA_CLK_ENB 10
+#define GPT2_CLK_ENB 11
+#define GPT3_CLK_ENB 12
+#define GPIO2_CLK_ENB 13
+#define SSP2_CLK_ENB 14
+#define ADC_CLK_ENB 15
+#define GPT1_CLK_ENB 11
+#define RTC_CLK_ENB 17
+#define GPIO1_CLK_ENB 18
+#define DMA_CLK_ENB 19
+#define SMI_CLK_ENB 21
+#define CLCD_CLK_ENB 22
+#define GMAC_CLK_ENB 23
+#define USBD_CLK_ENB 24
+#define USBH0_CLK_ENB 25
+#define USBH1_CLK_ENB 26
+
+#define PRSC1_CLK_CFG (MISC_BASE + 0x044)
+#define PRSC2_CLK_CFG (MISC_BASE + 0x048)
+#define PRSC3_CLK_CFG (MISC_BASE + 0x04C)
+/* gpt synthesizer register masks */
+#define GPT_MSCALE_SHIFT 0
+#define GPT_MSCALE_MASK 0xFFF
+#define GPT_NSCALE_SHIFT 12
+#define GPT_NSCALE_MASK 0xF
+
+#define AMEM_CLK_CFG (MISC_BASE + 0x050)
+#define EXPI_CLK_CFG (MISC_BASE + 0x054)
+#define CLCD_CLK_SYNT (MISC_BASE + 0x05C)
+#define FIRDA_CLK_SYNT (MISC_BASE + 0x060)
+#define UART_CLK_SYNT (MISC_BASE + 0x064)
+#define GMAC_CLK_SYNT (MISC_BASE + 0x068)
+#define RAS1_CLK_SYNT (MISC_BASE + 0x06C)
+#define RAS2_CLK_SYNT (MISC_BASE + 0x070)
+#define RAS3_CLK_SYNT (MISC_BASE + 0x074)
+#define RAS4_CLK_SYNT (MISC_BASE + 0x078)
+/* aux clk synthesiser register masks for irda to ras4 */
+#define AUX_SYNT_ENB 31
+#define AUX_EQ_SEL_SHIFT 30
+#define AUX_EQ_SEL_MASK 1
+#define AUX_EQ1_SEL 0
+#define AUX_EQ2_SEL 1
+#define AUX_XSCALE_SHIFT 16
+#define AUX_XSCALE_MASK 0xFFF
+#define AUX_YSCALE_SHIFT 0
+#define AUX_YSCALE_MASK 0xFFF
/* root clks */
/* 32 KHz oscillator clock */
@@ -623,53 +729,53 @@
/* array of all spear 6xx clock lookups */
static struct clk_lookup spear_clk_lookups[] = {
- { .con_id = "apb_pclk", .clk = &dummy_apb_pclk},
+ CLKDEV_INIT(NULL, "apb_pclk", &dummy_apb_pclk),
/* root clks */
- { .con_id = "osc_32k_clk", .clk = &osc_32k_clk},
- { .con_id = "osc_30m_clk", .clk = &osc_30m_clk},
+ CLKDEV_INIT(NULL, "osc_32k_clk", &osc_32k_clk),
+ CLKDEV_INIT(NULL, "osc_30m_clk", &osc_30m_clk),
/* clock derived from 32 KHz os clk */
- { .dev_id = "rtc-spear", .clk = &rtc_clk},
+ CLKDEV_INIT("rtc-spear", NULL, &rtc_clk),
/* clock derived from 30 MHz os clk */
- { .con_id = "pll1_clk", .clk = &pll1_clk},
- { .con_id = "pll3_48m_clk", .clk = &pll3_48m_clk},
- { .dev_id = "wdt", .clk = &wdt_clk},
+ CLKDEV_INIT(NULL, "pll1_clk", &pll1_clk),
+ CLKDEV_INIT(NULL, "pll3_48m_clk", &pll3_48m_clk),
+ CLKDEV_INIT("wdt", NULL, &wdt_clk),
/* clock derived from pll1 clk */
- { .con_id = "cpu_clk", .clk = &cpu_clk},
- { .con_id = "ahb_clk", .clk = &ahb_clk},
- { .con_id = "uart_synth_clk", .clk = &uart_synth_clk},
- { .con_id = "firda_synth_clk", .clk = &firda_synth_clk},
- { .con_id = "clcd_synth_clk", .clk = &clcd_synth_clk},
- { .con_id = "gpt0_synth_clk", .clk = &gpt0_synth_clk},
- { .con_id = "gpt2_synth_clk", .clk = &gpt2_synth_clk},
- { .con_id = "gpt3_synth_clk", .clk = &gpt3_synth_clk},
- { .dev_id = "d0000000.serial", .clk = &uart0_clk},
- { .dev_id = "d0080000.serial", .clk = &uart1_clk},
- { .dev_id = "firda", .clk = &firda_clk},
- { .dev_id = "clcd", .clk = &clcd_clk},
- { .dev_id = "gpt0", .clk = &gpt0_clk},
- { .dev_id = "gpt1", .clk = &gpt1_clk},
- { .dev_id = "gpt2", .clk = &gpt2_clk},
- { .dev_id = "gpt3", .clk = &gpt3_clk},
+ CLKDEV_INIT(NULL, "cpu_clk", &cpu_clk),
+ CLKDEV_INIT(NULL, "ahb_clk", &ahb_clk),
+ CLKDEV_INIT(NULL, "uart_synth_clk", &uart_synth_clk),
+ CLKDEV_INIT(NULL, "firda_synth_clk", &firda_synth_clk),
+ CLKDEV_INIT(NULL, "clcd_synth_clk", &clcd_synth_clk),
+ CLKDEV_INIT(NULL, "gpt0_synth_clk", &gpt0_synth_clk),
+ CLKDEV_INIT(NULL, "gpt2_synth_clk", &gpt2_synth_clk),
+ CLKDEV_INIT(NULL, "gpt3_synth_clk", &gpt3_synth_clk),
+ CLKDEV_INIT("d0000000.serial", NULL, &uart0_clk),
+ CLKDEV_INIT("d0080000.serial", NULL, &uart1_clk),
+ CLKDEV_INIT("firda", NULL, &firda_clk),
+ CLKDEV_INIT("clcd", NULL, &clcd_clk),
+ CLKDEV_INIT("gpt0", NULL, &gpt0_clk),
+ CLKDEV_INIT("gpt1", NULL, &gpt1_clk),
+ CLKDEV_INIT("gpt2", NULL, &gpt2_clk),
+ CLKDEV_INIT("gpt3", NULL, &gpt3_clk),
/* clock derived from pll3 clk */
- { .dev_id = "designware_udc", .clk = &usbd_clk},
- { .con_id = "usbh.0_clk", .clk = &usbh0_clk},
- { .con_id = "usbh.1_clk", .clk = &usbh1_clk},
+ CLKDEV_INIT("designware_udc", NULL, &usbd_clk),
+ CLKDEV_INIT(NULL, "usbh.0_clk", &usbh0_clk),
+ CLKDEV_INIT(NULL, "usbh.1_clk", &usbh1_clk),
/* clock derived from ahb clk */
- { .con_id = "apb_clk", .clk = &apb_clk},
- { .dev_id = "d0200000.i2c", .clk = &i2c_clk},
- { .dev_id = "dma", .clk = &dma_clk},
- { .dev_id = "jpeg", .clk = &jpeg_clk},
- { .dev_id = "gmac", .clk = &gmac_clk},
- { .dev_id = "smi", .clk = &smi_clk},
- { .dev_id = "fsmc-nand", .clk = &fsmc_clk},
+ CLKDEV_INIT(NULL, "apb_clk", &apb_clk),
+ CLKDEV_INIT("d0200000.i2c", NULL, &i2c_clk),
+ CLKDEV_INIT("fc400000.dma", NULL, &dma_clk),
+ CLKDEV_INIT("jpeg", NULL, &jpeg_clk),
+ CLKDEV_INIT("gmac", NULL, &gmac_clk),
+ CLKDEV_INIT("fc000000.flash", NULL, &smi_clk),
+ CLKDEV_INIT("d1800000.flash", NULL, &fsmc_clk),
/* clock derived from apb clk */
- { .dev_id = "adc", .clk = &adc_clk},
- { .dev_id = "ssp-pl022.0", .clk = &ssp0_clk},
- { .dev_id = "ssp-pl022.1", .clk = &ssp1_clk},
- { .dev_id = "ssp-pl022.2", .clk = &ssp2_clk},
- { .dev_id = "f0100000.gpio", .clk = &gpio0_clk},
- { .dev_id = "fc980000.gpio", .clk = &gpio1_clk},
- { .dev_id = "d8100000.gpio", .clk = &gpio2_clk},
+ CLKDEV_INIT("adc", NULL, &adc_clk),
+ CLKDEV_INIT("ssp-pl022.0", NULL, &ssp0_clk),
+ CLKDEV_INIT("ssp-pl022.1", NULL, &ssp1_clk),
+ CLKDEV_INIT("ssp-pl022.2", NULL, &ssp2_clk),
+ CLKDEV_INIT("f0100000.gpio", NULL, &gpio0_clk),
+ CLKDEV_INIT("fc980000.gpio", NULL, &gpio1_clk),
+ CLKDEV_INIT("d8100000.gpio", NULL, &gpio2_clk),
};
void __init spear6xx_clk_init(void)
diff --git a/arch/arm/mach-spear6xx/include/mach/generic.h b/arch/arm/mach-spear6xx/include/mach/generic.h
index 116b993..7167fd3 100644
--- a/arch/arm/mach-spear6xx/include/mach/generic.h
+++ b/arch/arm/mach-spear6xx/include/mach/generic.h
@@ -15,34 +15,9 @@
#define __MACH_GENERIC_H
#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/amba/bus.h>
-#include <asm/mach/time.h>
-#include <asm/mach/map.h>
-/*
- * Each GPT has 2 timer channels
- * Following GPT channels will be used as clock source and clockevent
- */
-#define SPEAR_GPT0_BASE SPEAR6XX_CPU_TMR_BASE
-#define SPEAR_GPT0_CHAN0_IRQ IRQ_CPU_GPT1_1
-#define SPEAR_GPT0_CHAN1_IRQ IRQ_CPU_GPT1_2
-
-/* Add spear6xx family device structure declarations here */
-extern struct amba_device gpio_device[];
-extern struct amba_device uart_device[];
-extern struct sys_timer spear6xx_timer;
-
-/* Add spear6xx family function declarations here */
-void __init spear_setup_timer(void);
-void __init spear6xx_map_io(void);
-void __init spear6xx_init_irq(void);
-void __init spear6xx_init(void);
-void __init spear600_init(void);
-void __init spear6xx_clk_init(void);
-
+void __init spear_setup_timer(resource_size_t base, int irq);
void spear_restart(char, const char *);
-
-/* Add spear600 machine device structure declarations here */
+void __init spear6xx_clk_init(void);
#endif /* __MACH_GENERIC_H */
diff --git a/arch/arm/mach-spear6xx/include/mach/hardware.h b/arch/arm/mach-spear6xx/include/mach/hardware.h
index 0b3f96a..40a8c178 100644
--- a/arch/arm/mach-spear6xx/include/mach/hardware.h
+++ b/arch/arm/mach-spear6xx/include/mach/hardware.h
@@ -1,23 +1 @@
-/*
- * arch/arm/mach-spear6xx/include/mach/hardware.h
- *
- * Hardware definitions for SPEAr6xx machine family
- *
- * Copyright (C) 2009 ST Microelectronics
- * Rajeev Kumar<rajeev-dlh.kumar@st.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#ifndef __MACH_HARDWARE_H
-#define __MACH_HARDWARE_H
-
-#include <plat/hardware.h>
-#include <mach/spear.h>
-
-/* Vitual to physical translation of statically mapped space */
-#define IO_ADDRESS(x) (x | 0xF0000000)
-
-#endif /* __MACH_HARDWARE_H */
+/* empty */
diff --git a/arch/arm/mach-spear6xx/include/mach/irqs.h b/arch/arm/mach-spear6xx/include/mach/irqs.h
index 8f214b0..2b73538 100644
--- a/arch/arm/mach-spear6xx/include/mach/irqs.h
+++ b/arch/arm/mach-spear6xx/include/mach/irqs.h
@@ -16,82 +16,13 @@
/* IRQ definitions */
/* VIC 1 */
-#define IRQ_INTRCOMM_SW_IRQ 0
-#define IRQ_INTRCOMM_CPU_1 1
-#define IRQ_INTRCOMM_CPU_2 2
-#define IRQ_INTRCOMM_RAS2A11_1 3
-#define IRQ_INTRCOMM_RAS2A11_2 4
-#define IRQ_INTRCOMM_RAS2A12_1 5
-#define IRQ_INTRCOMM_RAS2A12_2 6
-#define IRQ_GEN_RAS_0 7
-#define IRQ_GEN_RAS_1 8
-#define IRQ_GEN_RAS_2 9
-#define IRQ_GEN_RAS_3 10
-#define IRQ_GEN_RAS_4 11
-#define IRQ_GEN_RAS_5 12
-#define IRQ_GEN_RAS_6 13
-#define IRQ_GEN_RAS_7 14
-#define IRQ_GEN_RAS_8 15
+/* FIXME: probe this from DT */
#define IRQ_CPU_GPT1_1 16
-#define IRQ_CPU_GPT1_2 17
-#define IRQ_LOCAL_GPIO 18
-#define IRQ_PLL_UNLOCK 19
-#define IRQ_JPEG 20
-#define IRQ_FSMC 21
-#define IRQ_IRDA 22
-#define IRQ_RESERVED 23
-#define IRQ_UART_0 24
-#define IRQ_UART_1 25
-#define IRQ_SSP_1 26
-#define IRQ_SSP_2 27
-#define IRQ_I2C 28
-#define IRQ_GEN_RAS_9 29
-#define IRQ_GEN_RAS_10 30
-#define IRQ_GEN_RAS_11 31
-
-/* VIC 2 */
-#define IRQ_APPL_GPT1_1 32
-#define IRQ_APPL_GPT1_2 33
-#define IRQ_APPL_GPT2_1 34
-#define IRQ_APPL_GPT2_2 35
-#define IRQ_APPL_GPIO 36
-#define IRQ_APPL_SSP 37
-#define IRQ_APPL_ADC 38
-#define IRQ_APPL_RESERVED 39
-#define IRQ_AHB_EXP_MASTER 40
-#define IRQ_DDR_CONTROLLER 41
-#define IRQ_BASIC_DMA 42
-#define IRQ_BASIC_RESERVED1 43
-#define IRQ_BASIC_SMI 44
-#define IRQ_BASIC_CLCD 45
-#define IRQ_EXP_AHB_1 46
-#define IRQ_EXP_AHB_2 47
-#define IRQ_BASIC_GPT1_1 48
-#define IRQ_BASIC_GPT1_2 49
-#define IRQ_BASIC_RTC 50
-#define IRQ_BASIC_GPIO 51
-#define IRQ_BASIC_WDT 52
-#define IRQ_BASIC_RESERVED 53
-#define IRQ_AHB_EXP_SLAVE 54
-#define IRQ_GMAC_1 55
-#define IRQ_GMAC_2 56
-#define IRQ_USB_DEV 57
-#define IRQ_USB_H_OHCI_0 58
-#define IRQ_USB_H_EHCI_0 59
-#define IRQ_USB_H_OHCI_1 60
-#define IRQ_USB_H_EHCI_1 61
-#define IRQ_EXP_AHB_3 62
-#define IRQ_EXP_AHB_4 63
#define IRQ_VIC_END 64
/* GPIO pins virtual irqs */
-#define SPEAR_GPIO_INT_BASE IRQ_VIC_END
-#define SPEAR_GPIO0_INT_BASE SPEAR_GPIO_INT_BASE
-#define SPEAR_GPIO1_INT_BASE (SPEAR_GPIO0_INT_BASE + 8)
-#define SPEAR_GPIO2_INT_BASE (SPEAR_GPIO1_INT_BASE + 8)
-#define SPEAR_GPIO_INT_END (SPEAR_GPIO2_INT_BASE + 8)
-#define VIRTUAL_IRQS (SPEAR_GPIO_INT_END - IRQ_VIC_END)
-#define NR_IRQS (IRQ_VIC_END + VIRTUAL_IRQS)
+#define VIRTUAL_IRQS 24
+#define NR_IRQS (IRQ_VIC_END + VIRTUAL_IRQS)
#endif /* __MACH_IRQS_H */
diff --git a/arch/arm/mach-spear6xx/include/mach/misc_regs.h b/arch/arm/mach-spear6xx/include/mach/misc_regs.h
index 68c20a0..2b9aaa6 100644
--- a/arch/arm/mach-spear6xx/include/mach/misc_regs.h
+++ b/arch/arm/mach-spear6xx/include/mach/misc_regs.h
@@ -14,161 +14,7 @@
#ifndef __MACH_MISC_REGS_H
#define __MACH_MISC_REGS_H
-#include <mach/hardware.h>
-
#define MISC_BASE IOMEM(VA_SPEAR6XX_ICM3_MISC_REG_BASE)
-
-#define SOC_CFG_CTR (MISC_BASE + 0x000)
-#define DIAG_CFG_CTR (MISC_BASE + 0x004)
-#define PLL1_CTR (MISC_BASE + 0x008)
-#define PLL1_FRQ (MISC_BASE + 0x00C)
-#define PLL1_MOD (MISC_BASE + 0x010)
-#define PLL2_CTR (MISC_BASE + 0x014)
-/* PLL_CTR register masks */
-#define PLL_ENABLE 2
-#define PLL_MODE_SHIFT 4
-#define PLL_MODE_MASK 0x3
-#define PLL_MODE_NORMAL 0
-#define PLL_MODE_FRACTION 1
-#define PLL_MODE_DITH_DSB 2
-#define PLL_MODE_DITH_SSB 3
-
-#define PLL2_FRQ (MISC_BASE + 0x018)
-/* PLL FRQ register masks */
-#define PLL_DIV_N_SHIFT 0
-#define PLL_DIV_N_MASK 0xFF
-#define PLL_DIV_P_SHIFT 8
-#define PLL_DIV_P_MASK 0x7
-#define PLL_NORM_FDBK_M_SHIFT 24
-#define PLL_NORM_FDBK_M_MASK 0xFF
-#define PLL_DITH_FDBK_M_SHIFT 16
-#define PLL_DITH_FDBK_M_MASK 0xFFFF
-
-#define PLL2_MOD (MISC_BASE + 0x01C)
-#define PLL_CLK_CFG (MISC_BASE + 0x020)
-#define CORE_CLK_CFG (MISC_BASE + 0x024)
-/* CORE CLK CFG register masks */
-#define PLL_HCLK_RATIO_SHIFT 10
-#define PLL_HCLK_RATIO_MASK 0x3
-#define HCLK_PCLK_RATIO_SHIFT 8
-#define HCLK_PCLK_RATIO_MASK 0x3
-
-#define PERIP_CLK_CFG (MISC_BASE + 0x028)
-/* PERIP_CLK_CFG register masks */
-#define CLCD_CLK_SHIFT 2
-#define CLCD_CLK_MASK 0x3
-#define UART_CLK_SHIFT 4
-#define UART_CLK_MASK 0x1
-#define FIRDA_CLK_SHIFT 5
-#define FIRDA_CLK_MASK 0x3
-#define GPT0_CLK_SHIFT 8
-#define GPT1_CLK_SHIFT 10
-#define GPT2_CLK_SHIFT 11
-#define GPT3_CLK_SHIFT 12
-#define GPT_CLK_MASK 0x1
-#define AUX_CLK_PLL3_VAL 0
-#define AUX_CLK_PLL1_VAL 1
-
-#define PERIP1_CLK_ENB (MISC_BASE + 0x02C)
-/* PERIP1_CLK_ENB register masks */
-#define UART0_CLK_ENB 3
-#define UART1_CLK_ENB 4
-#define SSP0_CLK_ENB 5
-#define SSP1_CLK_ENB 6
-#define I2C_CLK_ENB 7
-#define JPEG_CLK_ENB 8
-#define FSMC_CLK_ENB 9
-#define FIRDA_CLK_ENB 10
-#define GPT2_CLK_ENB 11
-#define GPT3_CLK_ENB 12
-#define GPIO2_CLK_ENB 13
-#define SSP2_CLK_ENB 14
-#define ADC_CLK_ENB 15
-#define GPT1_CLK_ENB 11
-#define RTC_CLK_ENB 17
-#define GPIO1_CLK_ENB 18
-#define DMA_CLK_ENB 19
-#define SMI_CLK_ENB 21
-#define CLCD_CLK_ENB 22
-#define GMAC_CLK_ENB 23
-#define USBD_CLK_ENB 24
-#define USBH0_CLK_ENB 25
-#define USBH1_CLK_ENB 26
-
-#define SOC_CORE_ID (MISC_BASE + 0x030)
-#define RAS_CLK_ENB (MISC_BASE + 0x034)
-#define PERIP1_SOF_RST (MISC_BASE + 0x038)
-/* PERIP1_SOF_RST register masks */
-#define JPEG_SOF_RST 8
-
-#define SOC_USER_ID (MISC_BASE + 0x03C)
-#define RAS_SOF_RST (MISC_BASE + 0x040)
-#define PRSC1_CLK_CFG (MISC_BASE + 0x044)
-#define PRSC2_CLK_CFG (MISC_BASE + 0x048)
-#define PRSC3_CLK_CFG (MISC_BASE + 0x04C)
-/* gpt synthesizer register masks */
-#define GPT_MSCALE_SHIFT 0
-#define GPT_MSCALE_MASK 0xFFF
-#define GPT_NSCALE_SHIFT 12
-#define GPT_NSCALE_MASK 0xF
-
-#define AMEM_CLK_CFG (MISC_BASE + 0x050)
-#define EXPI_CLK_CFG (MISC_BASE + 0x054)
-#define CLCD_CLK_SYNT (MISC_BASE + 0x05C)
-#define FIRDA_CLK_SYNT (MISC_BASE + 0x060)
-#define UART_CLK_SYNT (MISC_BASE + 0x064)
-#define GMAC_CLK_SYNT (MISC_BASE + 0x068)
-#define RAS1_CLK_SYNT (MISC_BASE + 0x06C)
-#define RAS2_CLK_SYNT (MISC_BASE + 0x070)
-#define RAS3_CLK_SYNT (MISC_BASE + 0x074)
-#define RAS4_CLK_SYNT (MISC_BASE + 0x078)
-/* aux clk synthesiser register masks for irda to ras4 */
-#define AUX_SYNT_ENB 31
-#define AUX_EQ_SEL_SHIFT 30
-#define AUX_EQ_SEL_MASK 1
-#define AUX_EQ1_SEL 0
-#define AUX_EQ2_SEL 1
-#define AUX_XSCALE_SHIFT 16
-#define AUX_XSCALE_MASK 0xFFF
-#define AUX_YSCALE_SHIFT 0
-#define AUX_YSCALE_MASK 0xFFF
-
-#define ICM1_ARB_CFG (MISC_BASE + 0x07C)
-#define ICM2_ARB_CFG (MISC_BASE + 0x080)
-#define ICM3_ARB_CFG (MISC_BASE + 0x084)
-#define ICM4_ARB_CFG (MISC_BASE + 0x088)
-#define ICM5_ARB_CFG (MISC_BASE + 0x08C)
-#define ICM6_ARB_CFG (MISC_BASE + 0x090)
-#define ICM7_ARB_CFG (MISC_BASE + 0x094)
-#define ICM8_ARB_CFG (MISC_BASE + 0x098)
-#define ICM9_ARB_CFG (MISC_BASE + 0x09C)
#define DMA_CHN_CFG (MISC_BASE + 0x0A0)
-#define USB2_PHY_CFG (MISC_BASE + 0x0A4)
-#define GMAC_CFG_CTR (MISC_BASE + 0x0A8)
-#define EXPI_CFG_CTR (MISC_BASE + 0x0AC)
-#define PRC1_LOCK_CTR (MISC_BASE + 0x0C0)
-#define PRC2_LOCK_CTR (MISC_BASE + 0x0C4)
-#define PRC3_LOCK_CTR (MISC_BASE + 0x0C8)
-#define PRC4_LOCK_CTR (MISC_BASE + 0x0CC)
-#define PRC1_IRQ_CTR (MISC_BASE + 0x0D0)
-#define PRC2_IRQ_CTR (MISC_BASE + 0x0D4)
-#define PRC3_IRQ_CTR (MISC_BASE + 0x0D8)
-#define PRC4_IRQ_CTR (MISC_BASE + 0x0DC)
-#define PWRDOWN_CFG_CTR (MISC_BASE + 0x0E0)
-#define COMPSSTL_1V8_CFG (MISC_BASE + 0x0E4)
-#define COMPSSTL_2V5_CFG (MISC_BASE + 0x0E8)
-#define COMPCOR_3V3_CFG (MISC_BASE + 0x0EC)
-#define SSTLPAD_CFG_CTR (MISC_BASE + 0x0F0)
-#define BIST1_CFG_CTR (MISC_BASE + 0x0F4)
-#define BIST2_CFG_CTR (MISC_BASE + 0x0F8)
-#define BIST3_CFG_CTR (MISC_BASE + 0x0FC)
-#define BIST4_CFG_CTR (MISC_BASE + 0x100)
-#define BIST5_CFG_CTR (MISC_BASE + 0x104)
-#define BIST1_STS_RES (MISC_BASE + 0x108)
-#define BIST2_STS_RES (MISC_BASE + 0x10C)
-#define BIST3_STS_RES (MISC_BASE + 0x110)
-#define BIST4_STS_RES (MISC_BASE + 0x114)
-#define BIST5_STS_RES (MISC_BASE + 0x118)
-#define SYSERR_CFG_CTR (MISC_BASE + 0x11C)
#endif /* __MACH_MISC_REGS_H */
diff --git a/arch/arm/mach-spear6xx/include/mach/spear.h b/arch/arm/mach-spear6xx/include/mach/spear.h
index 7fd6215..d278ed0 100644
--- a/arch/arm/mach-spear6xx/include/mach/spear.h
+++ b/arch/arm/mach-spear6xx/include/mach/spear.h
@@ -15,69 +15,26 @@
#define __MACH_SPEAR6XX_H
#include <asm/memory.h>
-#include <mach/spear600.h>
-#define SPEAR6XX_ML_SDRAM_BASE UL(0x00000000)
/* ICM1 - Low speed connection */
#define SPEAR6XX_ICM1_BASE UL(0xD0000000)
-
+#define VA_SPEAR6XX_ICM1_BASE UL(0xFD000000)
#define SPEAR6XX_ICM1_UART0_BASE UL(0xD0000000)
-#define VA_SPEAR6XX_ICM1_UART0_BASE IO_ADDRESS(SPEAR6XX_ICM1_UART0_BASE)
-
-#define SPEAR6XX_ICM1_UART1_BASE UL(0xD0080000)
-#define SPEAR6XX_ICM1_SSP0_BASE UL(0xD0100000)
-#define SPEAR6XX_ICM1_SSP1_BASE UL(0xD0180000)
-#define SPEAR6XX_ICM1_I2C_BASE UL(0xD0200000)
-#define SPEAR6XX_ICM1_JPEG_BASE UL(0xD0800000)
-#define SPEAR6XX_ICM1_IRDA_BASE UL(0xD1000000)
-#define SPEAR6XX_ICM1_FSMC_BASE UL(0xD1800000)
-#define SPEAR6XX_ICM1_NAND_BASE UL(0xD2000000)
-#define SPEAR6XX_ICM1_SRAM_BASE UL(0xD2800000)
-
-/* ICM2 - Application Subsystem */
-#define SPEAR6XX_ICM2_BASE UL(0xD8000000)
-#define SPEAR6XX_ICM2_TMR0_BASE UL(0xD8000000)
-#define SPEAR6XX_ICM2_TMR1_BASE UL(0xD8080000)
-#define SPEAR6XX_ICM2_GPIO_BASE UL(0xD8100000)
-#define SPEAR6XX_ICM2_SSP2_BASE UL(0xD8180000)
-#define SPEAR6XX_ICM2_ADC_BASE UL(0xD8200000)
+#define VA_SPEAR6XX_ICM1_UART0_BASE (VA_SPEAR6XX_ICM1_2_BASE | SPEAR6XX_ICM1_UART0_BASE)
/* ML-1, 2 - Multi Layer CPU Subsystem */
#define SPEAR6XX_ML_CPU_BASE UL(0xF0000000)
+#define VA_SPEAR6XX_ML_CPU_BASE UL(0xF0000000)
#define SPEAR6XX_CPU_TMR_BASE UL(0xF0000000)
-#define SPEAR6XX_CPU_GPIO_BASE UL(0xF0100000)
-#define SPEAR6XX_CPU_VIC_SEC_BASE UL(0xF1000000)
-#define VA_SPEAR6XX_CPU_VIC_SEC_BASE IO_ADDRESS(SPEAR6XX_CPU_VIC_SEC_BASE)
-#define SPEAR6XX_CPU_VIC_PRI_BASE UL(0xF1100000)
-#define VA_SPEAR6XX_CPU_VIC_PRI_BASE IO_ADDRESS(SPEAR6XX_CPU_VIC_PRI_BASE)
/* ICM3 - Basic Subsystem */
-#define SPEAR6XX_ICM3_BASE UL(0xF8000000)
-#define SPEAR6XX_ICM3_SMEM_BASE UL(0xF8000000)
#define SPEAR6XX_ICM3_SMI_CTRL_BASE UL(0xFC000000)
-#define SPEAR6XX_ICM3_CLCD_BASE UL(0xFC200000)
+#define VA_SPEAR6XX_ICM3_SMI_CTRL_BASE UL(0xFC000000)
#define SPEAR6XX_ICM3_DMA_BASE UL(0xFC400000)
-#define SPEAR6XX_ICM3_SDRAM_CTRL_BASE UL(0xFC600000)
-#define SPEAR6XX_ICM3_TMR_BASE UL(0xFC800000)
-#define SPEAR6XX_ICM3_WDT_BASE UL(0xFC880000)
-#define SPEAR6XX_ICM3_RTC_BASE UL(0xFC900000)
-#define SPEAR6XX_ICM3_GPIO_BASE UL(0xFC980000)
#define SPEAR6XX_ICM3_SYS_CTRL_BASE UL(0xFCA00000)
-#define VA_SPEAR6XX_ICM3_SYS_CTRL_BASE IO_ADDRESS(SPEAR6XX_ICM3_SYS_CTRL_BASE)
+#define VA_SPEAR6XX_ICM3_SYS_CTRL_BASE (VA_SPEAR6XX_ICM3_SMI_CTRL_BASE | SPEAR6XX_ICM3_SYS_CTRL_BASE)
#define SPEAR6XX_ICM3_MISC_REG_BASE UL(0xFCA80000)
-#define VA_SPEAR6XX_ICM3_MISC_REG_BASE IO_ADDRESS(SPEAR6XX_ICM3_MISC_REG_BASE)
-
-/* ICM4 - High Speed Connection */
-#define SPEAR6XX_ICM4_BASE UL(0xE0000000)
-#define SPEAR6XX_ICM4_GMAC_BASE UL(0xE0800000)
-#define SPEAR6XX_ICM4_USBD_FIFO_BASE UL(0xE1000000)
-#define SPEAR6XX_ICM4_USBD_CSR_BASE UL(0xE1100000)
-#define SPEAR6XX_ICM4_USBD_PLDT_BASE UL(0xE1200000)
-#define SPEAR6XX_ICM4_USB_EHCI0_BASE UL(0xE1800000)
-#define SPEAR6XX_ICM4_USB_OHCI0_BASE UL(0xE1900000)
-#define SPEAR6XX_ICM4_USB_EHCI1_BASE UL(0xE2000000)
-#define SPEAR6XX_ICM4_USB_OHCI1_BASE UL(0xE2100000)
-#define SPEAR6XX_ICM4_USB_ARB_BASE UL(0xE2800000)
+#define VA_SPEAR6XX_ICM3_MISC_REG_BASE (VA_SPEAR6XX_ICM3_SMI_CTRL_BASE | SPEAR6XX_ICM3_MISC_REG_BASE)
/* Debug uart for linux, will be used for debug and uncompress messages */
#define SPEAR_DBG_UART_BASE SPEAR6XX_ICM1_UART0_BASE
diff --git a/arch/arm/mach-spear6xx/include/mach/spear600.h b/arch/arm/mach-spear6xx/include/mach/spear600.h
deleted file mode 100644
index c068cc5..0000000
--- a/arch/arm/mach-spear6xx/include/mach/spear600.h
+++ /dev/null
@@ -1,21 +0,0 @@
-/*
- * arch/arm/mach-spear66xx/include/mach/spear600.h
- *
- * SPEAr600 Machine specific definition
- *
- * Copyright (C) 2009 ST Microelectronics
- * Viresh Kumar<viresh.kumar@st.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#ifdef CONFIG_MACH_SPEAR600
-
-#ifndef __MACH_SPEAR600_H
-#define __MACH_SPEAR600_H
-
-#endif /* __MACH_SPEAR600_H */
-
-#endif /* CONFIG_MACH_SPEAR600 */
diff --git a/arch/arm/mach-spear6xx/spear6xx.c b/arch/arm/mach-spear6xx/spear6xx.c
index 2ed8b14..de194db 100644
--- a/arch/arm/mach-spear6xx/spear6xx.c
+++ b/arch/arm/mach-spear6xx/spear6xx.c
@@ -13,41 +13,404 @@
* warranty of any kind, whether express or implied.
*/
+#include <linux/amba/pl08x.h>
+#include <linux/clk.h>
+#include <linux/err.h>
#include <linux/of.h>
#include <linux/of_address.h>
#include <linux/of_irq.h>
#include <linux/of_platform.h>
+#include <asm/hardware/pl080.h>
#include <asm/hardware/vic.h>
#include <asm/mach/arch.h>
+#include <asm/mach/time.h>
+#include <asm/mach/map.h>
+#include <plat/pl080.h>
#include <mach/generic.h>
-#include <mach/hardware.h>
+#include <mach/spear.h>
-/* Following will create static virtual/physical mappings */
-static struct map_desc spear6xx_io_desc[] __initdata = {
+/* dmac device registration */
+static struct pl08x_channel_data spear600_dma_info[] = {
{
- .virtual = VA_SPEAR6XX_ICM1_UART0_BASE,
- .pfn = __phys_to_pfn(SPEAR6XX_ICM1_UART0_BASE),
- .length = SZ_4K,
+ .bus_id = "ssp1_rx",
+ .min_signal = 0,
+ .max_signal = 0,
+ .muxval = 0,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "ssp1_tx",
+ .min_signal = 1,
+ .max_signal = 1,
+ .muxval = 0,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "uart0_rx",
+ .min_signal = 2,
+ .max_signal = 2,
+ .muxval = 0,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "uart0_tx",
+ .min_signal = 3,
+ .max_signal = 3,
+ .muxval = 0,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "uart1_rx",
+ .min_signal = 4,
+ .max_signal = 4,
+ .muxval = 0,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "uart1_tx",
+ .min_signal = 5,
+ .max_signal = 5,
+ .muxval = 0,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "ssp2_rx",
+ .min_signal = 6,
+ .max_signal = 6,
+ .muxval = 0,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB2,
+ }, {
+ .bus_id = "ssp2_tx",
+ .min_signal = 7,
+ .max_signal = 7,
+ .muxval = 0,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB2,
+ }, {
+ .bus_id = "ssp0_rx",
+ .min_signal = 8,
+ .max_signal = 8,
+ .muxval = 0,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "ssp0_tx",
+ .min_signal = 9,
+ .max_signal = 9,
+ .muxval = 0,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "i2c_rx",
+ .min_signal = 10,
+ .max_signal = 10,
+ .muxval = 0,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "i2c_tx",
+ .min_signal = 11,
+ .max_signal = 11,
+ .muxval = 0,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "irda",
+ .min_signal = 12,
+ .max_signal = 12,
+ .muxval = 0,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "adc",
+ .min_signal = 13,
+ .max_signal = 13,
+ .muxval = 0,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB2,
+ }, {
+ .bus_id = "to_jpeg",
+ .min_signal = 14,
+ .max_signal = 14,
+ .muxval = 0,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "from_jpeg",
+ .min_signal = 15,
+ .max_signal = 15,
+ .muxval = 0,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "ras0_rx",
+ .min_signal = 0,
+ .max_signal = 0,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "ras0_tx",
+ .min_signal = 1,
+ .max_signal = 1,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "ras1_rx",
+ .min_signal = 2,
+ .max_signal = 2,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "ras1_tx",
+ .min_signal = 3,
+ .max_signal = 3,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "ras2_rx",
+ .min_signal = 4,
+ .max_signal = 4,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "ras2_tx",
+ .min_signal = 5,
+ .max_signal = 5,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "ras3_rx",
+ .min_signal = 6,
+ .max_signal = 6,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "ras3_tx",
+ .min_signal = 7,
+ .max_signal = 7,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "ras4_rx",
+ .min_signal = 8,
+ .max_signal = 8,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "ras4_tx",
+ .min_signal = 9,
+ .max_signal = 9,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "ras5_rx",
+ .min_signal = 10,
+ .max_signal = 10,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "ras5_tx",
+ .min_signal = 11,
+ .max_signal = 11,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "ras6_rx",
+ .min_signal = 12,
+ .max_signal = 12,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "ras6_tx",
+ .min_signal = 13,
+ .max_signal = 13,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "ras7_rx",
+ .min_signal = 14,
+ .max_signal = 14,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "ras7_tx",
+ .min_signal = 15,
+ .max_signal = 15,
+ .muxval = 1,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB1,
+ }, {
+ .bus_id = "ext0_rx",
+ .min_signal = 0,
+ .max_signal = 0,
+ .muxval = 2,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB2,
+ }, {
+ .bus_id = "ext0_tx",
+ .min_signal = 1,
+ .max_signal = 1,
+ .muxval = 2,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB2,
+ }, {
+ .bus_id = "ext1_rx",
+ .min_signal = 2,
+ .max_signal = 2,
+ .muxval = 2,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB2,
+ }, {
+ .bus_id = "ext1_tx",
+ .min_signal = 3,
+ .max_signal = 3,
+ .muxval = 2,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB2,
+ }, {
+ .bus_id = "ext2_rx",
+ .min_signal = 4,
+ .max_signal = 4,
+ .muxval = 2,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB2,
+ }, {
+ .bus_id = "ext2_tx",
+ .min_signal = 5,
+ .max_signal = 5,
+ .muxval = 2,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB2,
+ }, {
+ .bus_id = "ext3_rx",
+ .min_signal = 6,
+ .max_signal = 6,
+ .muxval = 2,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB2,
+ }, {
+ .bus_id = "ext3_tx",
+ .min_signal = 7,
+ .max_signal = 7,
+ .muxval = 2,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB2,
+ }, {
+ .bus_id = "ext4_rx",
+ .min_signal = 8,
+ .max_signal = 8,
+ .muxval = 2,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB2,
+ }, {
+ .bus_id = "ext4_tx",
+ .min_signal = 9,
+ .max_signal = 9,
+ .muxval = 2,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB2,
+ }, {
+ .bus_id = "ext5_rx",
+ .min_signal = 10,
+ .max_signal = 10,
+ .muxval = 2,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB2,
+ }, {
+ .bus_id = "ext5_tx",
+ .min_signal = 11,
+ .max_signal = 11,
+ .muxval = 2,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB2,
+ }, {
+ .bus_id = "ext6_rx",
+ .min_signal = 12,
+ .max_signal = 12,
+ .muxval = 2,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB2,
+ }, {
+ .bus_id = "ext6_tx",
+ .min_signal = 13,
+ .max_signal = 13,
+ .muxval = 2,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB2,
+ }, {
+ .bus_id = "ext7_rx",
+ .min_signal = 14,
+ .max_signal = 14,
+ .muxval = 2,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB2,
+ }, {
+ .bus_id = "ext7_tx",
+ .min_signal = 15,
+ .max_signal = 15,
+ .muxval = 2,
+ .cctl = 0,
+ .periph_buses = PL08X_AHB2,
+ },
+};
+
+struct pl08x_platform_data pl080_plat_data = {
+ .memcpy_channel = {
+ .bus_id = "memcpy",
+ .cctl = (PL080_BSIZE_16 << PL080_CONTROL_SB_SIZE_SHIFT | \
+ PL080_BSIZE_16 << PL080_CONTROL_DB_SIZE_SHIFT | \
+ PL080_WIDTH_32BIT << PL080_CONTROL_SWIDTH_SHIFT | \
+ PL080_WIDTH_32BIT << PL080_CONTROL_DWIDTH_SHIFT | \
+ PL080_CONTROL_PROT_BUFF | PL080_CONTROL_PROT_CACHE | \
+ PL080_CONTROL_PROT_SYS),
+ },
+ .lli_buses = PL08X_AHB1,
+ .mem_buses = PL08X_AHB1,
+ .get_signal = pl080_get_signal,
+ .put_signal = pl080_put_signal,
+ .slave_channels = spear600_dma_info,
+ .num_slave_channels = ARRAY_SIZE(spear600_dma_info),
+};
+
+/*
+ * Following will create 16MB static virtual/physical mappings
+ * PHYSICAL VIRTUAL
+ * 0xF0000000 0xF0000000
+ * 0xF1000000 0xF1000000
+ * 0xD0000000 0xFD000000
+ * 0xFC000000 0xFC000000
+ */
+struct map_desc spear6xx_io_desc[] __initdata = {
+ {
+ .virtual = VA_SPEAR6XX_ML_CPU_BASE,
+ .pfn = __phys_to_pfn(SPEAR6XX_ML_CPU_BASE),
+ .length = 2 * SZ_16M,
+ .type = MT_DEVICE
+ }, {
+ .virtual = VA_SPEAR6XX_ICM1_BASE,
+ .pfn = __phys_to_pfn(SPEAR6XX_ICM1_BASE),
+ .length = SZ_16M,
.type = MT_DEVICE
}, {
- .virtual = VA_SPEAR6XX_CPU_VIC_PRI_BASE,
- .pfn = __phys_to_pfn(SPEAR6XX_CPU_VIC_PRI_BASE),
- .length = SZ_4K,
- .type = MT_DEVICE
- }, {
- .virtual = VA_SPEAR6XX_CPU_VIC_SEC_BASE,
- .pfn = __phys_to_pfn(SPEAR6XX_CPU_VIC_SEC_BASE),
- .length = SZ_4K,
- .type = MT_DEVICE
- }, {
- .virtual = VA_SPEAR6XX_ICM3_SYS_CTRL_BASE,
- .pfn = __phys_to_pfn(SPEAR6XX_ICM3_SYS_CTRL_BASE),
- .length = SZ_4K,
- .type = MT_DEVICE
- }, {
- .virtual = VA_SPEAR6XX_ICM3_MISC_REG_BASE,
- .pfn = __phys_to_pfn(SPEAR6XX_ICM3_MISC_REG_BASE),
- .length = SZ_4K,
+ .virtual = VA_SPEAR6XX_ICM3_SMI_CTRL_BASE,
+ .pfn = __phys_to_pfn(SPEAR6XX_ICM3_SMI_CTRL_BASE),
+ .length = SZ_16M,
.type = MT_DEVICE
},
};
@@ -85,16 +448,24 @@
clk_put(gpt_clk);
clk_put(pclk);
- spear_setup_timer();
+ spear_setup_timer(SPEAR6XX_CPU_TMR_BASE, IRQ_CPU_GPT1_1);
}
struct sys_timer spear6xx_timer = {
.init = spear6xx_timer_init,
};
+/* Add auxdata to pass platform data */
+struct of_dev_auxdata spear6xx_auxdata_lookup[] __initdata = {
+ OF_DEV_AUXDATA("arm,pl080", SPEAR6XX_ICM3_DMA_BASE, NULL,
+ &pl080_plat_data),
+ {}
+};
+
static void __init spear600_dt_init(void)
{
- of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
+ of_platform_populate(NULL, of_default_bus_match_table,
+ spear6xx_auxdata_lookup, NULL);
}
static const char *spear600_dt_board_compat[] = {
diff --git a/arch/arm/plat-spear/Kconfig b/arch/arm/plat-spear/Kconfig
index 1bb3dbc..6c066fc 100644
--- a/arch/arm/plat-spear/Kconfig
+++ b/arch/arm/plat-spear/Kconfig
@@ -9,9 +9,10 @@
default ARCH_SPEAR3XX
config ARCH_SPEAR3XX
- bool "SPEAr3XX"
+ bool "ST SPEAr3xx with Device Tree"
select ARM_VIC
select CPU_ARM926T
+ select USE_OF
help
Supports for ARM's SPEAR3XX family
diff --git a/arch/arm/plat-spear/Makefile b/arch/arm/plat-spear/Makefile
index e0f2e5b..4af6258 100644
--- a/arch/arm/plat-spear/Makefile
+++ b/arch/arm/plat-spear/Makefile
@@ -3,6 +3,6 @@
#
# Common support
-obj-y := clock.o restart.o time.o
+obj-y := clock.o restart.o time.o pl080.o
obj-$(CONFIG_ARCH_SPEAR3XX) += shirq.o padmux.o
diff --git a/arch/arm/plat-spear/include/plat/debug-macro.S b/arch/arm/plat-spear/include/plat/debug-macro.S
index 02b160a..ab3de72 100644
--- a/arch/arm/plat-spear/include/plat/debug-macro.S
+++ b/arch/arm/plat-spear/include/plat/debug-macro.S
@@ -12,7 +12,7 @@
*/
#include <linux/amba/serial.h>
-#include <mach/hardware.h>
+#include <mach/spear.h>
.macro addruart, rp, rv, tmp
mov \rp, #SPEAR_DBG_UART_BASE @ Physical base
diff --git a/arch/arm/plat-spear/include/plat/hardware.h b/arch/arm/plat-spear/include/plat/hardware.h
deleted file mode 100644
index 70187d7..0000000
--- a/arch/arm/plat-spear/include/plat/hardware.h
+++ /dev/null
@@ -1,17 +0,0 @@
-/*
- * arch/arm/plat-spear/include/plat/hardware.h
- *
- * Hardware definitions for SPEAr
- *
- * Copyright (C) 2010 ST Microelectronics
- * Viresh Kumar<viresh.kumar@st.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#ifndef __PLAT_HARDWARE_H
-#define __PLAT_HARDWARE_H
-
-#endif /* __PLAT_HARDWARE_H */
diff --git a/arch/arm/plat-spear/include/plat/pl080.h b/arch/arm/plat-spear/include/plat/pl080.h
new file mode 100644
index 0000000..e14a3e4
--- /dev/null
+++ b/arch/arm/plat-spear/include/plat/pl080.h
@@ -0,0 +1,21 @@
+/*
+ * arch/arm/plat-spear/include/plat/pl080.h
+ *
+ * DMAC pl080 definitions for SPEAr platform
+ *
+ * Copyright (C) 2012 ST Microelectronics
+ * Viresh Kumar <viresh.kumar@st.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#ifndef __PLAT_PL080_H
+#define __PLAT_PL080_H
+
+struct pl08x_dma_chan;
+int pl080_get_signal(struct pl08x_dma_chan *ch);
+void pl080_put_signal(struct pl08x_dma_chan *ch);
+
+#endif /* __PLAT_PL080_H */
diff --git a/arch/arm/plat-spear/include/plat/uncompress.h b/arch/arm/plat-spear/include/plat/uncompress.h
index 1bf8452..6dd455b 100644
--- a/arch/arm/plat-spear/include/plat/uncompress.h
+++ b/arch/arm/plat-spear/include/plat/uncompress.h
@@ -13,7 +13,7 @@
#include <linux/io.h>
#include <linux/amba/serial.h>
-#include <mach/hardware.h>
+#include <mach/spear.h>
#ifndef __PLAT_UNCOMPRESS_H
#define __PLAT_UNCOMPRESS_H
diff --git a/arch/arm/plat-spear/pl080.c b/arch/arm/plat-spear/pl080.c
new file mode 100644
index 0000000..a56a067
--- /dev/null
+++ b/arch/arm/plat-spear/pl080.c
@@ -0,0 +1,80 @@
+/*
+ * arch/arm/plat-spear/pl080.c
+ *
+ * DMAC pl080 definitions for SPEAr platform
+ *
+ * Copyright (C) 2012 ST Microelectronics
+ * Viresh Kumar <viresh.kumar@st.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/amba/pl08x.h>
+#include <linux/amba/bus.h>
+#include <linux/bug.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/spinlock_types.h>
+#include <mach/spear.h>
+#include <mach/misc_regs.h>
+
+static spinlock_t lock = __SPIN_LOCK_UNLOCKED(x);
+
+struct {
+ unsigned char busy;
+ unsigned char val;
+} signals[16] = {{0, 0}, };
+
+int pl080_get_signal(struct pl08x_dma_chan *ch)
+{
+ const struct pl08x_channel_data *cd = ch->cd;
+ unsigned int signal = cd->min_signal, val;
+ unsigned long flags;
+
+ spin_lock_irqsave(&lock, flags);
+
+ /* Return if signal is already acquired by somebody else */
+ if (signals[signal].busy &&
+ (signals[signal].val != cd->muxval)) {
+ spin_unlock_irqrestore(&lock, flags);
+ return -EBUSY;
+ }
+
+ /* If acquiring for the first time, configure it */
+ if (!signals[signal].busy) {
+ val = readl(DMA_CHN_CFG);
+
+ /*
+ * Each request line has two bits in DMA_CHN_CFG register. To
+ * goto the bits of current request line, do left shift of
+ * value by 2 * signal number.
+ */
+ val &= ~(0x3 << (signal * 2));
+ val |= cd->muxval << (signal * 2);
+ writel(val, DMA_CHN_CFG);
+ }
+
+ signals[signal].busy++;
+ signals[signal].val = cd->muxval;
+ spin_unlock_irqrestore(&lock, flags);
+
+ return signal;
+}
+
+void pl080_put_signal(struct pl08x_dma_chan *ch)
+{
+ const struct pl08x_channel_data *cd = ch->cd;
+ unsigned long flags;
+
+ spin_lock_irqsave(&lock, flags);
+
+ /* if signal is not used */
+ if (!signals[cd->min_signal].busy)
+ BUG();
+
+ signals[cd->min_signal].busy--;
+
+ spin_unlock_irqrestore(&lock, flags);
+}
diff --git a/arch/arm/plat-spear/restart.c b/arch/arm/plat-spear/restart.c
index 16f203e..4471a23 100644
--- a/arch/arm/plat-spear/restart.c
+++ b/arch/arm/plat-spear/restart.c
@@ -13,7 +13,7 @@
#include <linux/io.h>
#include <asm/system_misc.h>
#include <asm/hardware/sp810.h>
-#include <mach/hardware.h>
+#include <mach/spear.h>
#include <mach/generic.h>
void spear_restart(char mode, const char *cmd)
diff --git a/arch/arm/plat-spear/time.c b/arch/arm/plat-spear/time.c
index abb5bde..a3164d1 100644
--- a/arch/arm/plat-spear/time.c
+++ b/arch/arm/plat-spear/time.c
@@ -15,14 +15,13 @@
#include <linux/err.h>
#include <linux/init.h>
#include <linux/interrupt.h>
+#include <linux/ioport.h>
#include <linux/io.h>
#include <linux/kernel.h>
#include <linux/time.h>
#include <linux/irq.h>
#include <asm/mach/time.h>
#include <mach/generic.h>
-#include <mach/hardware.h>
-#include <mach/irqs.h>
/*
* We would use TIMER0 and TIMER1 as clockevent and clocksource.
@@ -175,7 +174,7 @@
.handler = spear_timer_interrupt
};
-static void __init spear_clockevent_init(void)
+static void __init spear_clockevent_init(int irq)
{
u32 tick_rate;
@@ -195,19 +194,19 @@
clockevents_register_device(&clkevt);
- setup_irq(SPEAR_GPT0_CHAN0_IRQ, &spear_timer_irq);
+ setup_irq(irq, &spear_timer_irq);
}
-void __init spear_setup_timer(void)
+void __init spear_setup_timer(resource_size_t base, int irq)
{
int ret;
- if (!request_mem_region(SPEAR_GPT0_BASE, SZ_1K, "gpt0")) {
+ if (!request_mem_region(base, SZ_1K, "gpt0")) {
pr_err("%s:cannot get IO addr\n", __func__);
return;
}
- gpt_base = (void __iomem *)ioremap(SPEAR_GPT0_BASE, SZ_1K);
+ gpt_base = ioremap(base, SZ_1K);
if (!gpt_base) {
pr_err("%s:ioremap failed for gpt\n", __func__);
goto err_mem;
@@ -225,7 +224,7 @@
goto err_clk;
}
- spear_clockevent_init();
+ spear_clockevent_init(irq);
spear_clocksource_init();
return;
@@ -235,5 +234,5 @@
err_iomap:
iounmap(gpt_base);
err_mem:
- release_mem_region(SPEAR_GPT0_BASE, SZ_1K);
+ release_mem_region(base, SZ_1K);
}
diff --git a/drivers/of/address.c b/drivers/of/address.c
index 66d96f1..7e262a6 100644
--- a/drivers/of/address.c
+++ b/drivers/of/address.c
@@ -1,4 +1,5 @@
+#include <linux/device.h>
#include <linux/io.h>
#include <linux/ioport.h>
#include <linux/module.h>