diff --git a/drivers/net/wireless/Kconfig b/drivers/net/wireless/Kconfig
index 2dddbd0..fe819a7 100644
--- a/drivers/net/wireless/Kconfig
+++ b/drivers/net/wireless/Kconfig
@@ -194,127 +194,6 @@
 
 	  The driver can be compiled as a module and will be named "airo".
 
-config HERMES
-	tristate "Hermes chipset 802.11b support (Orinoco/Prism2/Symbol)"
-	depends on (PPC_PMAC || PCI || PCMCIA) && WLAN_80211
-	select WIRELESS_EXT
-	select FW_LOADER
-	select CRYPTO
-	select CRYPTO_MICHAEL_MIC
-	---help---
-	  A driver for 802.11b wireless cards based on the "Hermes" or
-	  Intersil HFA384x (Prism 2) MAC controller.  This includes the vast
-	  majority of the PCMCIA 802.11b cards (which are nearly all rebadges)
-	  - except for the Cisco/Aironet cards.  Cards supported include the
-	  Apple Airport (not a PCMCIA card), WavelanIEEE/Orinoco,
-	  Cabletron/EnteraSys Roamabout, ELSA AirLancer, MELCO Buffalo, Avaya,
-	  IBM High Rate Wireless, Farralon Syyline, Samsung MagicLAN, Netgear
-	  MA401, LinkSys WPC-11, D-Link DWL-650, 3Com AirConnect, Intel
-	  IPW2011, and Symbol Spectrum24 High Rate amongst others.
-
-	  This option includes the guts of the driver, but in order to
-	  actually use a card you will also need to enable support for PCMCIA
-	  Hermes cards, PLX9052 based PCI adaptors or the Apple Airport below.
-
-	  You will also very likely also need the Wireless Tools in order to
-	  configure your card and that /etc/pcmcia/wireless.opts works :
-	  <http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/Tools.html>
-
-config HERMES_CACHE_FW_ON_INIT
-	bool "Cache Hermes firmware on driver initialisation"
-	depends on HERMES
-	default y
-	---help---
-	  Say Y to cache any firmware required by the Hermes drivers
-	  on startup.  The firmware will remain cached until the
-	  driver is unloaded.  The cache uses 64K of RAM.
-
-	  Otherwise load the firmware from userspace as required.  In
-	  this case the driver should be unloaded and restarted
-	  whenever the firmware is changed.
-
-	  If you are not sure, say Y.
-
-config APPLE_AIRPORT
-	tristate "Apple Airport support (built-in)"
-	depends on PPC_PMAC && HERMES
-	help
-	  Say Y here to support the Airport 802.11b wireless Ethernet hardware
-	  built into the Macintosh iBook and other recent PowerPC-based
-	  Macintosh machines. This is essentially a Lucent Orinoco card with 
-	  a non-standard interface.
-
-	  This driver does not support the Airport Extreme (802.11b/g). Use
-	  the BCM43xx driver for Airport Extreme cards.
-
-config PLX_HERMES
-	tristate "Hermes in PLX9052 based PCI adaptor support (Netgear MA301 etc.)"
-	depends on PCI && HERMES
-	help
-	  Enable support for PCMCIA cards supported by the "Hermes" (aka
-	  orinoco) driver when used in PLX9052 based PCI adaptors.  These
-	  adaptors are not a full PCMCIA controller but act as a more limited
-	  PCI <-> PCMCIA bridge.  Several vendors sell such adaptors so that
-	  802.11b PCMCIA cards can be used in desktop machines.  The Netgear
-	  MA301 is such an adaptor.
-
-config TMD_HERMES
-	tristate "Hermes in TMD7160 based PCI adaptor support"
-	depends on PCI && HERMES
-	help
-	  Enable support for PCMCIA cards supported by the "Hermes" (aka
-	  orinoco) driver when used in TMD7160 based PCI adaptors.  These
-	  adaptors are not a full PCMCIA controller but act as a more limited
-	  PCI <-> PCMCIA bridge.  Several vendors sell such adaptors so that
-	  802.11b PCMCIA cards can be used in desktop machines.
-
-config NORTEL_HERMES
-	tristate "Nortel emobility PCI adaptor support"
-	depends on PCI && HERMES
-	help
-	  Enable support for PCMCIA cards supported by the "Hermes" (aka
-	  orinoco) driver when used in Nortel emobility PCI adaptors.  These
-	  adaptors are not full PCMCIA controllers, but act as a more limited
-	  PCI <-> PCMCIA bridge.
-
-config PCI_HERMES
-	tristate "Prism 2.5 PCI 802.11b adaptor support"
-	depends on PCI && HERMES
-	help
-	  Enable support for PCI and mini-PCI 802.11b wireless NICs based on
-	  the Prism 2.5 chipset.  These are true PCI cards, not the 802.11b
-	  PCMCIA cards bundled with PCI<->PCMCIA adaptors which are also
-	  common.  Some of the built-in wireless adaptors in laptops are of
-	  this variety.
-
-config PCMCIA_HERMES
-	tristate "Hermes PCMCIA card support"
-	depends on PCMCIA && HERMES
-	---help---
-	  A driver for "Hermes" chipset based PCMCIA wireless adaptors, such
-	  as the Lucent WavelanIEEE/Orinoco cards and their OEM (Cabletron/
-	  EnteraSys RoamAbout 802.11, ELSA Airlancer, Melco Buffalo and
-	  others).  It should also be usable on various Prism II based cards
-	  such as the Linksys, D-Link and Farallon Skyline.  It should also
-	  work on Symbol cards such as the 3Com AirConnect and Ericsson WLAN.
-
-	  You will very likely need the Wireless Tools in order to
-	  configure your card and that /etc/pcmcia/wireless.opts works:
-	  <http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/Tools.html>.
-
-config PCMCIA_SPECTRUM
-	tristate "Symbol Spectrum24 Trilogy PCMCIA card support"
-	depends on PCMCIA && HERMES
-	---help---
-
-	  This is a driver for 802.11b cards using RAM-loadable Symbol
-	  firmware, such as Symbol Wireless Networker LA4100, CompactFlash
-	  cards by Socket Communications and Intel PRO/Wireless 2011B.
-
-	  This driver requires firmware download on startup.  Utilities
-	  for downloading Symbol firmware are available at
-	  <http://sourceforge.net/projects/orinoco/>
-
 config ATMEL
       tristate "Atmel at76c50x chipset  802.11b support"
       depends on (PCI || PCMCIA) && WLAN_80211
@@ -596,5 +475,6 @@
 source "drivers/net/wireless/b43legacy/Kconfig"
 source "drivers/net/wireless/zd1211rw/Kconfig"
 source "drivers/net/wireless/rt2x00/Kconfig"
+source "drivers/net/wireless/orinoco/Kconfig"
 
 endmenu