ARM: OMAP3: Initialize more devices for LDP
Based on an earlier patches by Stanley.Miao <stanley.miao@windriver.com>
and Nishant Kamat <nskamat@ti.com>.
Note that at the ads7846 support still needs support for vaux_control
for the touchscreen to work.
Signed-off-by: Tony Lindgren <tony@atomide.com>
diff --git a/arch/arm/mach-omap2/board-ldp.c b/arch/arm/mach-omap2/board-ldp.c
index 59ac8ed..d8bc0a7 100644
--- a/arch/arm/mach-omap2/board-ldp.c
+++ b/arch/arm/mach-omap2/board-ldp.c
@@ -16,11 +16,13 @@
#include <linux/platform_device.h>
#include <linux/delay.h>
#include <linux/input.h>
+#include <linux/gpio_keys.h>
#include <linux/workqueue.h>
#include <linux/err.h>
#include <linux/clk.h>
#include <linux/spi/spi.h>
#include <linux/spi/ads7846.h>
+#include <linux/regulator/machine.h>
#include <linux/i2c/twl4030.h>
#include <linux/io.h>
#include <linux/smsc911x.h>
@@ -39,6 +41,7 @@
#include <asm/delay.h>
#include <mach/control.h>
#include <mach/usb.h>
+#include <mach/keypad.h>
#include "mmc-twl4030.h"
@@ -77,6 +80,165 @@
},
};
+static int ldp_twl4030_keymap[] = {
+ KEY(0, 0, KEY_1),
+ KEY(1, 0, KEY_2),
+ KEY(2, 0, KEY_3),
+ KEY(0, 1, KEY_4),
+ KEY(1, 1, KEY_5),
+ KEY(2, 1, KEY_6),
+ KEY(3, 1, KEY_F5),
+ KEY(0, 2, KEY_7),
+ KEY(1, 2, KEY_8),
+ KEY(2, 2, KEY_9),
+ KEY(3, 2, KEY_F6),
+ KEY(0, 3, KEY_F7),
+ KEY(1, 3, KEY_0),
+ KEY(2, 3, KEY_F8),
+ PERSISTENT_KEY(4, 5),
+ KEY(4, 4, KEY_VOLUMEUP),
+ KEY(5, 5, KEY_VOLUMEDOWN),
+ 0
+};
+
+static struct twl4030_keypad_data ldp_kp_twl4030_data = {
+ .rows = 6,
+ .cols = 6,
+ .keymap = ldp_twl4030_keymap,
+ .keymapsize = ARRAY_SIZE(ldp_twl4030_keymap),
+ .rep = 1,
+};
+
+static struct gpio_keys_button ldp_gpio_keys_buttons[] = {
+ [0] = {
+ .code = KEY_ENTER,
+ .gpio = 101,
+ .desc = "enter sw",
+ .active_low = 1,
+ .debounce_interval = 30,
+ },
+ [1] = {
+ .code = KEY_F1,
+ .gpio = 102,
+ .desc = "func 1",
+ .active_low = 1,
+ .debounce_interval = 30,
+ },
+ [2] = {
+ .code = KEY_F2,
+ .gpio = 103,
+ .desc = "func 2",
+ .active_low = 1,
+ .debounce_interval = 30,
+ },
+ [3] = {
+ .code = KEY_F3,
+ .gpio = 104,
+ .desc = "func 3",
+ .active_low = 1,
+ .debounce_interval = 30,
+ },
+ [4] = {
+ .code = KEY_F4,
+ .gpio = 105,
+ .desc = "func 4",
+ .active_low = 1,
+ .debounce_interval = 30,
+ },
+ [5] = {
+ .code = KEY_LEFT,
+ .gpio = 106,
+ .desc = "left sw",
+ .active_low = 1,
+ .debounce_interval = 30,
+ },
+ [6] = {
+ .code = KEY_RIGHT,
+ .gpio = 107,
+ .desc = "right sw",
+ .active_low = 1,
+ .debounce_interval = 30,
+ },
+ [7] = {
+ .code = KEY_UP,
+ .gpio = 108,
+ .desc = "up sw",
+ .active_low = 1,
+ .debounce_interval = 30,
+ },
+ [8] = {
+ .code = KEY_DOWN,
+ .gpio = 109,
+ .desc = "down sw",
+ .active_low = 1,
+ .debounce_interval = 30,
+ },
+};
+
+static struct gpio_keys_platform_data ldp_gpio_keys = {
+ .buttons = ldp_gpio_keys_buttons,
+ .nbuttons = ARRAY_SIZE(ldp_gpio_keys_buttons),
+ .rep = 1,
+};
+
+static struct platform_device ldp_gpio_keys_device = {
+ .name = "gpio-keys",
+ .id = -1,
+ .dev = {
+ .platform_data = &ldp_gpio_keys,
+ },
+};
+
+static int ts_gpio;
+
+/**
+ * @brief ads7846_dev_init : Requests & sets GPIO line for pen-irq
+ *
+ * @return - void. If request gpio fails then Flag KERN_ERR.
+ */
+static void ads7846_dev_init(void)
+{
+ if (gpio_request(ts_gpio, "ads7846 irq") < 0) {
+ printk(KERN_ERR "can't get ads746 pen down GPIO\n");
+ return;
+ }
+
+ gpio_direction_input(ts_gpio);
+ omap_set_gpio_debounce(ts_gpio, 1);
+ omap_set_gpio_debounce_time(ts_gpio, 0xa);
+}
+
+static int ads7846_get_pendown_state(void)
+{
+ return !gpio_get_value(ts_gpio);
+}
+
+static struct ads7846_platform_data tsc2046_config __initdata = {
+ .get_pendown_state = ads7846_get_pendown_state,
+ .keep_vref_on = 1,
+};
+
+static struct omap2_mcspi_device_config tsc2046_mcspi_config = {
+ .turbo_mode = 0,
+ .single_channel = 1, /* 0: slave, 1: master */
+};
+
+static struct spi_board_info ldp_spi_board_info[] __initdata = {
+ [0] = {
+ /*
+ * TSC2046 operates at a max freqency of 2MHz, so
+ * operate slightly below at 1.5MHz
+ */
+ .modalias = "ads7846",
+ .bus_num = 1,
+ .chip_select = 0,
+ .max_speed_hz = 1500000,
+ .controller_data = &tsc2046_mcspi_config,
+ .irq = 0,
+ .platform_data = &tsc2046_config,
+ },
+};
+
static inline void __init ldp_init_smsc911x(void)
{
int eth_cs;
@@ -132,18 +294,49 @@
{ OMAP_TAG_LCD, &ldp_lcd_config },
};
+static struct twl4030_usb_data ldp_usb_data = {
+ .usb_mode = T2_USB_MODE_ULPI,
+};
+
static struct twl4030_gpio_platform_data ldp_gpio_data = {
.gpio_base = OMAP_MAX_GPIO_LINES,
.irq_base = TWL4030_GPIO_IRQ_BASE,
.irq_end = TWL4030_GPIO_IRQ_END,
};
+static struct twl4030_madc_platform_data ldp_madc_data = {
+ .irq_line = 1,
+};
+
+static struct regulator_consumer_supply ldp_vmmc1_supply = {
+ .supply = "vmmc",
+};
+
+/* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */
+static struct regulator_init_data ldp_vmmc1 = {
+ .constraints = {
+ .min_uV = 1850000,
+ .max_uV = 3150000,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL
+ | REGULATOR_MODE_STANDBY,
+ .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
+ | REGULATOR_CHANGE_MODE
+ | REGULATOR_CHANGE_STATUS,
+ },
+ .num_consumer_supplies = 1,
+ .consumer_supplies = &ldp_vmmc1_supply,
+};
+
static struct twl4030_platform_data ldp_twldata = {
.irq_base = TWL4030_IRQ_BASE,
.irq_end = TWL4030_IRQ_END,
/* platform_data for children goes here */
+ .madc = &ldp_madc_data,
+ .usb = &ldp_usb_data,
+ .vmmc1 = &ldp_vmmc1,
.gpio = &ldp_gpio_data,
+ .keypad = &ldp_kp_twl4030_data,
};
static struct i2c_board_info __initdata ldp_i2c_boardinfo[] = {
@@ -177,6 +370,7 @@
static struct platform_device *ldp_devices[] __initdata = {
&ldp_smsc911x_device,
&ldp_lcd_device,
+ &ldp_gpio_keys_device,
};
static void __init omap_ldp_init(void)
@@ -185,9 +379,17 @@
platform_add_devices(ldp_devices, ARRAY_SIZE(ldp_devices));
omap_board_config = ldp_config;
omap_board_config_size = ARRAY_SIZE(ldp_config);
+ ts_gpio = 54;
+ ldp_spi_board_info[0].irq = gpio_to_irq(ts_gpio);
+ spi_register_board_info(ldp_spi_board_info,
+ ARRAY_SIZE(ldp_spi_board_info));
+ ads7846_dev_init();
omap_serial_init();
- twl4030_mmc_init(mmc);
usb_musb_init();
+
+ twl4030_mmc_init(mmc);
+ /* link regulators to MMC adapters */
+ ldp_vmmc1_supply.dev = mmc[0].dev;
}
static void __init omap_ldp_map_io(void)