mac80211: convert to channel definition struct
Convert mac80211 (and where necessary, some drivers a
little bit) to the new channel definition struct.
This will allow extending mac80211 for VHT, which is
currently restricted to channel contexts since there
are no drivers using that which makes it easier. As
I also don't care about VHT for drivers not using the
channel context API, I won't convert the previous API
to VHT support.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
diff --git a/net/mac80211/mesh_plink.c b/net/mac80211/mesh_plink.c
index 7a47f40..ca52dfd 100644
--- a/net/mac80211/mesh_plink.c
+++ b/net/mac80211/mesh_plink.c
@@ -111,7 +111,7 @@
u16 ht_opmode;
bool non_ht_sta = false, ht20_sta = false;
- if (sdata->vif.bss_conf.channel_type == NL80211_CHAN_NO_HT)
+ if (sdata->vif.bss_conf.chandef.width == NL80211_CHAN_WIDTH_20_NOHT)
return 0;
rcu_read_lock();
@@ -120,14 +120,14 @@
sta->plink_state != NL80211_PLINK_ESTAB)
continue;
- switch (sta->ch_type) {
- case NL80211_CHAN_NO_HT:
+ switch (sta->ch_width) {
+ case NL80211_CHAN_WIDTH_20_NOHT:
mpl_dbg(sdata,
"mesh_plink %pM: nonHT sta (%pM) is present\n",
sdata->vif.addr, sta->sta.addr);
non_ht_sta = true;
goto out;
- case NL80211_CHAN_HT20:
+ case NL80211_CHAN_WIDTH_20:
mpl_dbg(sdata,
"mesh_plink %pM: HT20 sta (%pM) is present\n",
sdata->vif.addr, sta->sta.addr);
@@ -142,7 +142,7 @@
if (non_ht_sta)
ht_opmode = IEEE80211_HT_OP_MODE_PROTECTION_NONHT_MIXED;
else if (ht20_sta &&
- sdata->vif.bss_conf.channel_type > NL80211_CHAN_HT20)
+ sdata->vif.bss_conf.chandef.width > NL80211_CHAN_WIDTH_20)
ht_opmode = IEEE80211_HT_OP_MODE_PROTECTION_20MHZ;
else
ht_opmode = IEEE80211_HT_OP_MODE_PROTECTION_NONE;
@@ -372,7 +372,7 @@
sta->sta.supp_rates[band] = rates;
if (elems->ht_cap_elem &&
- sdata->vif.bss_conf.channel_type != NL80211_CHAN_NO_HT)
+ sdata->vif.bss_conf.chandef.width != NL80211_CHAN_WIDTH_20_NOHT)
ieee80211_ht_cap_ie_to_sta_ht_cap(sdata, sband,
elems->ht_cap_elem,
&sta->sta.ht_cap);
@@ -380,12 +380,15 @@
memset(&sta->sta.ht_cap, 0, sizeof(sta->sta.ht_cap));
if (elems->ht_operation) {
+ struct cfg80211_chan_def chandef;
+
if (!(elems->ht_operation->ht_param &
IEEE80211_HT_PARAM_CHAN_WIDTH_ANY))
sta->sta.ht_cap.cap &=
~IEEE80211_HT_CAP_SUP_WIDTH_20_40;
- sta->ch_type =
- ieee80211_ht_oper_to_channel_type(elems->ht_operation);
+ ieee80211_ht_oper_to_chandef(sdata->vif.bss_conf.chandef.chan,
+ elems->ht_operation, &chandef);
+ sta->ch_width = chandef.width;
}
rate_control_rate_init(sta);