ARM: OMAP4+: PRM: add support for passing status register/bit info to reset
AM43xx has slightly different reset register layout compared to OMAP4+,
with varying status bit shifts and status register offsets. Current
code assumes static offsets and identical status / reset control bit
shifts, which is wrong. This patch adds PRM core support for passing
the actual implementations from hwmod code. AM43xx mappings will be fixed
in subsequent patch.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reported-by: Dave Gerlach <d-gerlach@ti.com>
Reported-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
diff --git a/arch/arm/mach-omap2/prminst44xx.c b/arch/arm/mach-omap2/prminst44xx.c
index c4859c4..d0b15db 100644
--- a/arch/arm/mach-omap2/prminst44xx.c
+++ b/arch/arm/mach-omap2/prminst44xx.c
@@ -87,12 +87,6 @@
return v;
}
-/*
- * Address offset (in bytes) between the reset control and the reset
- * status registers: 4 bytes on OMAP4
- */
-#define OMAP4_RST_CTRL_ST_OFFSET 4
-
/**
* omap4_prminst_is_hardreset_asserted - read the HW reset line state of
* submodules contained in the hwmod module
@@ -141,11 +135,11 @@
* omap4_prminst_deassert_hardreset - deassert a submodule hardreset line and
* wait
* @shift: register bit shift corresponding to the reset line to deassert
- * @st_shift: status bit offset, not used for OMAP4+
+ * @st_shift: status bit offset corresponding to the reset line
* @part: PRM partition
* @inst: PRM instance offset
* @rstctrl_offs: reset register offset
- * @st_offs: reset status register offset, not used for OMAP4+
+ * @rstst_offs: reset status register offset
*
* Some IPs like dsp, ipu or iva contain processors that require an HW
* reset line to be asserted / deasserted in order to fully enable the
@@ -157,11 +151,11 @@
* of reset, or -EBUSY if the submodule did not exit reset promptly.
*/
int omap4_prminst_deassert_hardreset(u8 shift, u8 st_shift, u8 part, s16 inst,
- u16 rstctrl_offs, u16 st_offs)
+ u16 rstctrl_offs, u16 rstst_offs)
{
int c;
u32 mask = 1 << shift;
- u16 rstst_offs = rstctrl_offs + OMAP4_RST_CTRL_ST_OFFSET;
+ u32 st_mask = 1 << st_shift;
/* Check the current status to avoid de-asserting the line twice */
if (omap4_prminst_is_hardreset_asserted(shift, part, inst,
@@ -169,13 +163,13 @@
return -EEXIST;
/* Clear the reset status by writing 1 to the status bit */
- omap4_prminst_rmw_inst_reg_bits(0xffffffff, mask, part, inst,
+ omap4_prminst_rmw_inst_reg_bits(0xffffffff, st_mask, part, inst,
rstst_offs);
/* de-assert the reset control line */
omap4_prminst_rmw_inst_reg_bits(mask, 0, part, inst, rstctrl_offs);
/* wait the status to be set */
- omap_test_timeout(omap4_prminst_is_hardreset_asserted(shift, part, inst,
- rstst_offs),
+ omap_test_timeout(omap4_prminst_is_hardreset_asserted(st_shift, part,
+ inst, rstst_offs),
MAX_MODULE_HARDRESET_WAIT, c);
return (c == MAX_MODULE_HARDRESET_WAIT) ? -EBUSY : 0;