diff --git a/Documentation/devicetree/bindings/reset/sirf,rstc.txt b/Documentation/devicetree/bindings/reset/sirf,rstc.txt
new file mode 100644
index 0000000..0505de7
--- /dev/null
+++ b/Documentation/devicetree/bindings/reset/sirf,rstc.txt
@@ -0,0 +1,42 @@
+CSR SiRFSoC Reset Controller
+======================================
+
+Please also refer to reset.txt in this directory for common reset
+controller binding usage.
+
+Required properties:
+- compatible: Should be "sirf,prima2-rstc" or "sirf,marco-rstc"
+- reg: should be register base and length as documented in the
+  datasheet
+- #reset-cells: 1, see below
+
+example:
+
+rstc: reset-controller@88010000 {
+	compatible = "sirf,prima2-rstc";
+	reg = <0x88010000 0x1000>;
+	#reset-cells = <1>;
+};
+
+Specifying reset lines connected to IP modules
+==============================================
+
+The reset controller(rstc) manages various reset sources. This module provides
+reset signals for most blocks in system. Those device nodes should specify the
+reset line on the rstc in their resets property, containing a phandle to the
+rstc device node and a RESET_INDEX specifying which module to reset, as described
+in reset.txt.
+
+For SiRFSoC, RESET_INDEX is just reset_bit defined in SW_RST0 and SW_RST1 registers.
+For modules whose rest_bit is in SW_RST0, its RESET_INDEX is 0~31. For modules whose
+rest_bit is in SW_RST1, its RESET_INDEX is 32~63.
+
+example:
+
+vpp@90020000 {
+	compatible = "sirf,prima2-vpp";
+	reg = <0x90020000 0x10000>;
+	interrupts = <31>;
+	clocks = <&clks 35>;
+	resets = <&rstc 6>;
+};
diff --git a/Documentation/devicetree/bindings/serial/atmel-usart.txt b/Documentation/devicetree/bindings/serial/atmel-usart.txt
index 9c5d19a..17c1042 100644
--- a/Documentation/devicetree/bindings/serial/atmel-usart.txt
+++ b/Documentation/devicetree/bindings/serial/atmel-usart.txt
@@ -13,6 +13,8 @@
 Optional properties:
 - atmel,use-dma-rx: use of PDC or DMA for receiving data
 - atmel,use-dma-tx: use of PDC or DMA for transmitting data
+- rts-gpios: specify a GPIO for RTS line. It will use specified PIO instead of the peripheral
+  function pin for the USART RTS feature. If unsure, don't specify this property.
 - add dma bindings for dma transfer:
 	- dmas: DMA specifier, consisting of a phandle to DMA controller node,
 		memory peripheral interface and USART DMA channel ID, FIFO configuration.
@@ -33,6 +35,7 @@
 		clock-names = "usart";
 		atmel,use-dma-rx;
 		atmel,use-dma-tx;
+		rts-gpios = <&pioD 15 0>;
 	};
 
 - use DMA:
diff --git a/MAINTAINERS b/MAINTAINERS
index fb08dce..9dbf7f1 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -1167,6 +1167,14 @@
 W:	http://www.arm.linux.org.uk/
 S:	Maintained
 
+ARM/QUALCOMM SUPPORT
+M:	Kumar Gala <galak@codeaurora.org>
+M:	David Brown <davidb@codeaurora.org>
+L:	linux-arm-msm@vger.kernel.org
+S:	Maintained
+F:	arch/arm/mach-qcom/
+T:	git git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom.git
+
 ARM/RADISYS ENP2611 MACHINE SUPPORT
 M:	Lennert Buytenhek <kernel@wantstofly.org>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index e254198..d5fee71 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -306,9 +306,11 @@
 config ARCH_MULTIPLATFORM
 	bool "Allow multiple platforms to be selected"
 	depends on MMU
+	select ARCH_WANT_OPTIONAL_GPIOLIB
 	select ARM_PATCH_PHYS_VIRT
 	select AUTO_ZRELADDR
 	select COMMON_CLK
+	select GENERIC_CLOCKEVENTS
 	select MULTI_IRQ_HANDLER
 	select SPARSE_IRQ
 	select USE_OF
@@ -421,9 +423,6 @@
 	depends on !MMU
 	select ARCH_REQUIRE_GPIOLIB
 	select ARM_NVIC
-	# CLKSRC_MMIO is wrong here, but needed until a proper fix is merged,
-	# i.e. CLKSRC_EFM32 selecting CLKSRC_MMIO
-	select CLKSRC_MMIO
 	select CLKSRC_OF
 	select COMMON_CLK
 	select CPU_V7M
@@ -657,9 +656,8 @@
 	help
 	  Support for Intel/Marvell's PXA2xx/PXA3xx processor line.
 
-config ARCH_MSM_NODT
-	bool "Qualcomm MSM"
-	select ARCH_MSM
+config ARCH_MSM
+	bool "Qualcomm MSM (non-multiplatform)"
 	select ARCH_REQUIRE_GPIOLIB
 	select COMMON_CLK
 	select GENERIC_CLOCKEVENTS
@@ -908,16 +906,18 @@
 config ARCH_MULTI_V6
 	bool "ARMv6 based platforms (ARM11)"
 	select ARCH_MULTI_V6_V7
-	select CPU_V6
+	select CPU_V6K
 
 config ARCH_MULTI_V7
 	bool "ARMv7 based platforms (Cortex-A, PJ4, Scorpion, Krait)"
 	default y
 	select ARCH_MULTI_V6_V7
 	select CPU_V7
+	select HAVE_SMP
 
 config ARCH_MULTI_V6_V7
 	bool
+	select MIGHT_HAVE_CACHE_L2X0
 
 config ARCH_MULTI_CPU_AUTO
 	def_bool !(ARCH_MULTI_V4 || ARCH_MULTI_V4T || ARCH_MULTI_V6_V7)
@@ -925,6 +925,13 @@
 
 endmenu
 
+config ARCH_VIRT
+	bool "Dummy Virtual Machine" if ARCH_MULTI_V7
+	select ARM_AMBA
+	select ARM_GIC
+	select ARM_PSCI
+	select HAVE_ARM_ARCH_TIMER
+
 #
 # This is sorted alphabetically by mach-* pathname.  However, plat-*
 # Kconfigs may be included either alphabetically (according to the
@@ -1005,6 +1012,8 @@
 
 source "arch/arm/mach-mmp/Kconfig"
 
+source "arch/arm/mach-qcom/Kconfig"
+
 source "arch/arm/mach-realview/Kconfig"
 
 source "arch/arm/mach-rockchip/Kconfig"
@@ -1048,8 +1057,6 @@
 source "arch/arm/mach-vexpress/Kconfig"
 source "arch/arm/plat-versatile/Kconfig"
 
-source "arch/arm/mach-virt/Kconfig"
-
 source "arch/arm/mach-vt8500/Kconfig"
 
 source "arch/arm/mach-w90x900/Kconfig"
diff --git a/arch/arm/Kconfig.debug b/arch/arm/Kconfig.debug
index 0531da8..84ca340 100644
--- a/arch/arm/Kconfig.debug
+++ b/arch/arm/Kconfig.debug
@@ -956,7 +956,7 @@
 
 config DEBUG_MSM_UART
 	bool
-	depends on ARCH_MSM
+	depends on ARCH_MSM || ARCH_QCOM
 
 config DEBUG_LL_INCLUDE
 	string
@@ -1145,7 +1145,7 @@
 
 config DEBUG_UNCOMPRESS
 	bool
-	depends on ARCH_MULTIPLATFORM || ARCH_MSM
+	depends on ARCH_MULTIPLATFORM || ARCH_MSM || ARCH_EXYNOS
 	default y if DEBUG_LL && !DEBUG_OMAP2PLUS_UART && \
 		     (!DEBUG_TEGRA_UART || !ZBOOT_ROM)
 	help
@@ -1161,7 +1161,8 @@
 
 config UNCOMPRESS_INCLUDE
 	string
-	default "debug/uncompress.h" if ARCH_MULTIPLATFORM || ARCH_MSM
+	default "debug/uncompress.h" if ARCH_MULTIPLATFORM || ARCH_MSM || \
+					ARCH_EXYNOS
 	default "mach/uncompress.h"
 
 config EARLY_PRINTK
diff --git a/arch/arm/Makefile b/arch/arm/Makefile
index 08a9ef5..dd1bd7e 100644
--- a/arch/arm/Makefile
+++ b/arch/arm/Makefile
@@ -180,6 +180,7 @@
 machine-$(CONFIG_ARCH_ORION5X)		+= orion5x
 machine-$(CONFIG_ARCH_PICOXCELL)	+= picoxcell
 machine-$(CONFIG_ARCH_PXA)		+= pxa
+machine-$(CONFIG_ARCH_QCOM)		+= qcom
 machine-$(CONFIG_ARCH_REALVIEW)		+= realview
 machine-$(CONFIG_ARCH_ROCKCHIP)		+= rockchip
 machine-$(CONFIG_ARCH_RPC)		+= rpc
@@ -199,7 +200,6 @@
 machine-$(CONFIG_ARCH_U8500)		+= ux500
 machine-$(CONFIG_ARCH_VERSATILE)	+= versatile
 machine-$(CONFIG_ARCH_VEXPRESS)		+= vexpress
-machine-$(CONFIG_ARCH_VIRT)		+= virt
 machine-$(CONFIG_ARCH_VT8500)		+= vt8500
 machine-$(CONFIG_ARCH_W90X900)		+= w90x900
 machine-$(CONFIG_ARCH_ZYNQ)		+= zynq
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 6d1e43d..3269029 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -119,9 +119,6 @@
 	kirkwood-ts219-6282.dtb
 dtb-$(CONFIG_ARCH_MARCO) += marco-evb.dtb
 dtb-$(CONFIG_ARCH_MOXART) += moxart-uc7112lx.dtb
-dtb-$(CONFIG_ARCH_MSM) += qcom-msm8660-surf.dtb \
-	qcom-msm8960-cdp.dtb \
-	qcom-apq8074-dragonboard.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += armada-370-db.dtb \
 	armada-370-mirabox.dtb \
 	armada-370-netgear-rn102.dtb \
@@ -233,6 +230,9 @@
 	dra7-evm.dtb
 dtb-$(CONFIG_ARCH_ORION5X) += orion5x-lacie-ethernet-disk-mini-v2.dtb
 dtb-$(CONFIG_ARCH_PRIMA2) += prima2-evb.dtb
+dtb-$(CONFIG_ARCH_QCOM) += qcom-msm8660-surf.dtb \
+	qcom-msm8960-cdp.dtb \
+	qcom-apq8074-dragonboard.dtb
 dtb-$(CONFIG_ARCH_U8500) += ste-snowball.dtb \
 	ste-hrefprev60-stuib.dtb \
 	ste-hrefprev60-tvk.dtb \
diff --git a/arch/arm/boot/dts/atlas6.dtsi b/arch/arm/boot/dts/atlas6.dtsi
index f8674bc..f7f9caf 100644
--- a/arch/arm/boot/dts/atlas6.dtsi
+++ b/arch/arm/boot/dts/atlas6.dtsi
@@ -65,9 +65,10 @@
 				#clock-cells = <1>;
 			};
 
-			reset-controller@88010000 {
+			rstc: reset-controller@88010000 {
 				compatible = "sirf,prima2-rstc";
 				reg = <0x88010000 0x1000>;
+				#reset-cells = <1>;
 			};
 
 			rsc-controller@88020000 {
diff --git a/arch/arm/boot/dts/marco.dtsi b/arch/arm/boot/dts/marco.dtsi
index 1579c34..0c9647d 100644
--- a/arch/arm/boot/dts/marco.dtsi
+++ b/arch/arm/boot/dts/marco.dtsi
@@ -58,9 +58,10 @@
 			#size-cells = <1>;
 			ranges = <0xc2000000 0xc2000000 0x1000000>;
 
-			reset-controller@c2000000 {
+			rstc: reset-controller@c2000000 {
 				compatible = "sirf,marco-rstc";
 				reg = <0xc2000000 0x10000>;
+				#reset-cells = <1>;
 			};
 		};
 
diff --git a/arch/arm/boot/dts/prima2.dtsi b/arch/arm/boot/dts/prima2.dtsi
index 0e21993..0ca0d7f 100644
--- a/arch/arm/boot/dts/prima2.dtsi
+++ b/arch/arm/boot/dts/prima2.dtsi
@@ -76,9 +76,10 @@
 				#clock-cells = <1>;
 			};
 
-			reset-controller@88010000 {
+			rstc: reset-controller@88010000 {
 				compatible = "sirf,prima2-rstc";
 				reg = <0x88010000 0x1000>;
+				#reset-cells = <1>;
 			};
 
 			rsc-controller@88020000 {
diff --git a/arch/arm/boot/dts/qcom-msm8660-surf.dts b/arch/arm/boot/dts/qcom-msm8660-surf.dts
index 68a72f5..169bad9 100644
--- a/arch/arm/boot/dts/qcom-msm8660-surf.dts
+++ b/arch/arm/boot/dts/qcom-msm8660-surf.dts
@@ -1,63 +1,6 @@
-/dts-v1/;
-
-/include/ "skeleton.dtsi"
-
-#include <dt-bindings/clock/qcom,gcc-msm8660.h>
+#include "qcom-msm8660.dtsi"
 
 / {
 	model = "Qualcomm MSM8660 SURF";
 	compatible = "qcom,msm8660-surf", "qcom,msm8660";
-	interrupt-parent = <&intc>;
-
-	intc: interrupt-controller@2080000 {
-		compatible = "qcom,msm-8660-qgic";
-		interrupt-controller;
-		#interrupt-cells = <3>;
-		reg = < 0x02080000 0x1000 >,
-		      < 0x02081000 0x1000 >;
-	};
-
-	timer@2000000 {
-		compatible = "qcom,scss-timer", "qcom,msm-timer";
-		interrupts = <1 0 0x301>,
-			     <1 1 0x301>,
-			     <1 2 0x301>;
-		reg = <0x02000000 0x100>;
-		clock-frequency = <27000000>,
-				  <32768>;
-		cpu-offset = <0x40000>;
-	};
-
-	msmgpio: gpio@800000 {
-		compatible = "qcom,msm-gpio";
-		reg = <0x00800000 0x4000>;
-		gpio-controller;
-		#gpio-cells = <2>;
-		ngpio = <173>;
-		interrupts = <0 16 0x4>;
-		interrupt-controller;
-		#interrupt-cells = <2>;
-	};
-
-	gcc: clock-controller@900000 {
-		compatible = "qcom,gcc-msm8660";
-		#clock-cells = <1>;
-		#reset-cells = <1>;
-		reg = <0x900000 0x4000>;
-	};
-
-	serial@19c40000 {
-		compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
-		reg = <0x19c40000 0x1000>,
-		      <0x19c00000 0x1000>;
-		interrupts = <0 195 0x0>;
-		clocks = <&gcc GSBI12_UART_CLK>, <&gcc GSBI12_H_CLK>;
-		clock-names = "core", "iface";
-	};
-
-	qcom,ssbi@500000 {
-		compatible = "qcom,ssbi";
-		reg = <0x500000 0x1000>;
-		qcom,controller-type = "pmic-arbiter";
-	};
 };
diff --git a/arch/arm/boot/dts/qcom-msm8660.dtsi b/arch/arm/boot/dts/qcom-msm8660.dtsi
new file mode 100644
index 0000000..69d6c4e
--- /dev/null
+++ b/arch/arm/boot/dts/qcom-msm8660.dtsi
@@ -0,0 +1,63 @@
+/dts-v1/;
+
+/include/ "skeleton.dtsi"
+
+#include <dt-bindings/clock/qcom,gcc-msm8660.h>
+
+/ {
+	model = "Qualcomm MSM8660";
+	compatible = "qcom,msm8660";
+	interrupt-parent = <&intc>;
+
+	intc: interrupt-controller@2080000 {
+		compatible = "qcom,msm-8660-qgic";
+		interrupt-controller;
+		#interrupt-cells = <3>;
+		reg = < 0x02080000 0x1000 >,
+		      < 0x02081000 0x1000 >;
+	};
+
+	timer@2000000 {
+		compatible = "qcom,scss-timer", "qcom,msm-timer";
+		interrupts = <1 0 0x301>,
+			     <1 1 0x301>,
+			     <1 2 0x301>;
+		reg = <0x02000000 0x100>;
+		clock-frequency = <27000000>,
+				  <32768>;
+		cpu-offset = <0x40000>;
+	};
+
+	msmgpio: gpio@800000 {
+		compatible = "qcom,msm-gpio";
+		reg = <0x00800000 0x4000>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		ngpio = <173>;
+		interrupts = <0 16 0x4>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gcc: clock-controller@900000 {
+		compatible = "qcom,gcc-msm8660";
+		#clock-cells = <1>;
+		#reset-cells = <1>;
+		reg = <0x900000 0x4000>;
+	};
+
+	serial@19c40000 {
+		compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
+		reg = <0x19c40000 0x1000>,
+		      <0x19c00000 0x1000>;
+		interrupts = <0 195 0x0>;
+		clocks = <&gcc GSBI12_UART_CLK>, <&gcc GSBI12_H_CLK>;
+		clock-names = "core", "iface";
+	};
+
+	qcom,ssbi@500000 {
+		compatible = "qcom,ssbi";
+		reg = <0x500000 0x1000>;
+		qcom,controller-type = "pmic-arbiter";
+	};
+};
diff --git a/arch/arm/boot/dts/qcom-msm8960-cdp.dts b/arch/arm/boot/dts/qcom-msm8960-cdp.dts
index 7c30de4..a58fb88 100644
--- a/arch/arm/boot/dts/qcom-msm8960-cdp.dts
+++ b/arch/arm/boot/dts/qcom-msm8960-cdp.dts
@@ -1,70 +1,6 @@
-/dts-v1/;
-
-/include/ "skeleton.dtsi"
-
-#include <dt-bindings/clock/qcom,gcc-msm8960.h>
+#include "qcom-msm8960.dtsi"
 
 / {
 	model = "Qualcomm MSM8960 CDP";
 	compatible = "qcom,msm8960-cdp", "qcom,msm8960";
-	interrupt-parent = <&intc>;
-
-	intc: interrupt-controller@2000000 {
-		compatible = "qcom,msm-qgic2";
-		interrupt-controller;
-		#interrupt-cells = <3>;
-		reg = < 0x02000000 0x1000 >,
-		      < 0x02002000 0x1000 >;
-	};
-
-	timer@200a000 {
-		compatible = "qcom,kpss-timer", "qcom,msm-timer";
-		interrupts = <1 1 0x301>,
-			     <1 2 0x301>,
-			     <1 3 0x301>;
-		reg = <0x0200a000 0x100>;
-		clock-frequency = <27000000>,
-				  <32768>;
-		cpu-offset = <0x80000>;
-	};
-
-	msmgpio: gpio@800000 {
-		compatible = "qcom,msm-gpio";
-		gpio-controller;
-		#gpio-cells = <2>;
-		ngpio = <150>;
-		interrupts = <0 16 0x4>;
-		interrupt-controller;
-		#interrupt-cells = <2>;
-		reg = <0x800000 0x4000>;
-	};
-
-	gcc: clock-controller@900000 {
-		compatible = "qcom,gcc-msm8960";
-		#clock-cells = <1>;
-		#reset-cells = <1>;
-		reg = <0x900000 0x4000>;
-	};
-
-	clock-controller@4000000 {
-		compatible = "qcom,mmcc-msm8960";
-		reg = <0x4000000 0x1000>;
-		#clock-cells = <1>;
-		#reset-cells = <1>;
-	};
-
-	serial@16440000 {
-		compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
-		reg = <0x16440000 0x1000>,
-		      <0x16400000 0x1000>;
-		interrupts = <0 154 0x0>;
-		clocks = <&gcc GSBI5_UART_CLK>, <&gcc GSBI5_H_CLK>;
-		clock-names = "core", "iface";
-	};
-
-	qcom,ssbi@500000 {
-		compatible = "qcom,ssbi";
-		reg = <0x500000 0x1000>;
-		qcom,controller-type = "pmic-arbiter";
-	};
 };
diff --git a/arch/arm/boot/dts/qcom-msm8960.dtsi b/arch/arm/boot/dts/qcom-msm8960.dtsi
new file mode 100644
index 0000000..ff00282
--- /dev/null
+++ b/arch/arm/boot/dts/qcom-msm8960.dtsi
@@ -0,0 +1,70 @@
+/dts-v1/;
+
+/include/ "skeleton.dtsi"
+
+#include <dt-bindings/clock/qcom,gcc-msm8960.h>
+
+/ {
+	model = "Qualcomm MSM8960";
+	compatible = "qcom,msm8960";
+	interrupt-parent = <&intc>;
+
+	intc: interrupt-controller@2000000 {
+		compatible = "qcom,msm-qgic2";
+		interrupt-controller;
+		#interrupt-cells = <3>;
+		reg = < 0x02000000 0x1000 >,
+		      < 0x02002000 0x1000 >;
+	};
+
+	timer@200a000 {
+		compatible = "qcom,kpss-timer", "qcom,msm-timer";
+		interrupts = <1 1 0x301>,
+			     <1 2 0x301>,
+			     <1 3 0x301>;
+		reg = <0x0200a000 0x100>;
+		clock-frequency = <27000000>,
+				  <32768>;
+		cpu-offset = <0x80000>;
+	};
+
+	msmgpio: gpio@800000 {
+		compatible = "qcom,msm-gpio";
+		gpio-controller;
+		#gpio-cells = <2>;
+		ngpio = <150>;
+		interrupts = <0 16 0x4>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		reg = <0x800000 0x4000>;
+	};
+
+	gcc: clock-controller@900000 {
+		compatible = "qcom,gcc-msm8960";
+		#clock-cells = <1>;
+		#reset-cells = <1>;
+		reg = <0x900000 0x4000>;
+	};
+
+	clock-controller@4000000 {
+		compatible = "qcom,mmcc-msm8960";
+		reg = <0x4000000 0x1000>;
+		#clock-cells = <1>;
+		#reset-cells = <1>;
+	};
+
+	serial@16440000 {
+		compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
+		reg = <0x16440000 0x1000>,
+		      <0x16400000 0x1000>;
+		interrupts = <0 154 0x0>;
+		clocks = <&gcc GSBI5_UART_CLK>, <&gcc GSBI5_H_CLK>;
+		clock-names = "core", "iface";
+	};
+
+	qcom,ssbi@500000 {
+		compatible = "qcom,ssbi";
+		reg = <0x500000 0x1000>;
+		qcom,controller-type = "pmic-arbiter";
+	};
+};
diff --git a/arch/arm/configs/clps711x_defconfig b/arch/arm/configs/clps711x_defconfig
index 9e8c831..0facf9d 100644
--- a/arch/arm/configs/clps711x_defconfig
+++ b/arch/arm/configs/clps711x_defconfig
@@ -15,7 +15,6 @@
 CONFIG_ARCH_CLEP7312=y
 CONFIG_ARCH_EDB7211=y
 CONFIG_ARCH_P720T=y
-CONFIG_ARCH_FORTUNET=y
 CONFIG_AEABI=y
 CONFIG_ZBOOT_ROM_TEXT=0x0
 CONFIG_ZBOOT_ROM_BSS=0x0
@@ -27,7 +26,6 @@
 # CONFIG_IPV6 is not set
 CONFIG_IRDA=y
 CONFIG_IRTTY_SIR=y
-CONFIG_EP7211_DONGLE=y
 # CONFIG_WIRELESS is not set
 CONFIG_MTD=y
 CONFIG_MTD_CMDLINE_PARTS=y
@@ -58,6 +56,7 @@
 # CONFIG_INPUT is not set
 # CONFIG_SERIO is not set
 # CONFIG_VT is not set
+CONFIG_SERIAL_CLPS711X=y
 CONFIG_SERIAL_CLPS711X_CONSOLE=y
 # CONFIG_HW_RANDOM is not set
 CONFIG_I2C=y
diff --git a/arch/arm/include/asm/timex.h b/arch/arm/include/asm/timex.h
index 83f2aa8..f6fcc67 100644
--- a/arch/arm/include/asm/timex.h
+++ b/arch/arm/include/asm/timex.h
@@ -12,12 +12,6 @@
 #ifndef _ASMARM_TIMEX_H
 #define _ASMARM_TIMEX_H
 
-#ifdef CONFIG_ARCH_MULTIPLATFORM
-#define CLOCK_TICK_RATE 1000000
-#else
-#include <mach/timex.h>
-#endif
-
 typedef unsigned long cycles_t;
 #define get_cycles()	({ cycles_t c; read_current_timer(&c) ? 0 : c; })
 
diff --git a/arch/arm/include/debug/samsung.S b/arch/arm/include/debug/samsung.S
index f3a9cff..8d8d922 100644
--- a/arch/arm/include/debug/samsung.S
+++ b/arch/arm/include/debug/samsung.S
@@ -9,7 +9,7 @@
  * published by the Free Software Foundation.
 */
 
-#include <plat/regs-serial.h>
+#include <linux/serial_s3c.h>
 
 /* The S5PV210/S5PC110 implementations are as belows. */
 
diff --git a/arch/arm/mach-at91/at91rm9200.c b/arch/arm/mach-at91/at91rm9200.c
index e47f5fd..787bb50 100644
--- a/arch/arm/mach-at91/at91rm9200.c
+++ b/arch/arm/mach-at91/at91rm9200.c
@@ -21,6 +21,7 @@
 #include <mach/at91rm9200.h>
 #include <mach/at91_st.h>
 #include <mach/cpu.h>
+#include <mach/hardware.h>
 
 #include "at91_aic.h"
 #include "soc.h"
diff --git a/arch/arm/mach-at91/at91rm9200_devices.c b/arch/arm/mach-at91/at91rm9200_devices.c
index 3ebc979..f3f19f2 100644
--- a/arch/arm/mach-at91/at91rm9200_devices.c
+++ b/arch/arm/mach-at91/at91rm9200_devices.c
@@ -21,6 +21,7 @@
 #include <mach/at91rm9200.h>
 #include <mach/at91rm9200_mc.h>
 #include <mach/at91_ramc.h>
+#include <mach/hardware.h>
 
 #include "board.h"
 #include "generic.h"
@@ -922,6 +923,7 @@
 static struct atmel_uart_data dbgu_data = {
 	.use_dma_tx	= 0,
 	.use_dma_rx	= 0,		/* DBGU not capable of receive DMA */
+	.rts_gpio	= -EINVAL,
 };
 
 static u64 dbgu_dmamask = DMA_BIT_MASK(32);
@@ -960,6 +962,7 @@
 static struct atmel_uart_data uart0_data = {
 	.use_dma_tx	= 1,
 	.use_dma_rx	= 1,
+	.rts_gpio	= -EINVAL,
 };
 
 static u64 uart0_dmamask = DMA_BIT_MASK(32);
@@ -987,9 +990,10 @@
 	if (pins & ATMEL_UART_RTS) {
 		/*
 		 * AT91RM9200 Errata #39 - RTS0 is not internally connected to PA21.
-		 *  We need to drive the pin manually.  Default is off (RTS is active low).
+		 * We need to drive the pin manually. The serial driver will driver
+		 * this to high when initializing.
 		 */
-		at91_set_gpio_output(AT91_PIN_PA21, 1);
+		uart0_data.rts_gpio = AT91_PIN_PA21;
 	}
 }
 
@@ -1009,6 +1013,7 @@
 static struct atmel_uart_data uart1_data = {
 	.use_dma_tx	= 1,
 	.use_dma_rx	= 1,
+	.rts_gpio	= -EINVAL,
 };
 
 static u64 uart1_dmamask = DMA_BIT_MASK(32);
@@ -1060,6 +1065,7 @@
 static struct atmel_uart_data uart2_data = {
 	.use_dma_tx	= 1,
 	.use_dma_rx	= 1,
+	.rts_gpio	= -EINVAL,
 };
 
 static u64 uart2_dmamask = DMA_BIT_MASK(32);
@@ -1103,6 +1109,7 @@
 static struct atmel_uart_data uart3_data = {
 	.use_dma_tx	= 1,
 	.use_dma_rx	= 1,
+	.rts_gpio	= -EINVAL,
 };
 
 static u64 uart3_dmamask = DMA_BIT_MASK(32);
diff --git a/arch/arm/mach-at91/at91rm9200_time.c b/arch/arm/mach-at91/at91rm9200_time.c
index bc7b363..7fd13ae 100644
--- a/arch/arm/mach-at91/at91rm9200_time.c
+++ b/arch/arm/mach-at91/at91rm9200_time.c
@@ -31,6 +31,7 @@
 #include <asm/mach/time.h>
 
 #include <mach/at91_st.h>
+#include <mach/hardware.h>
 
 static unsigned long last_crtr;
 static u32 irqmask;
diff --git a/arch/arm/mach-at91/at91sam9260.c b/arch/arm/mach-at91/at91sam9260.c
index 6c821e5..c3d22be 100644
--- a/arch/arm/mach-at91/at91sam9260.c
+++ b/arch/arm/mach-at91/at91sam9260.c
@@ -21,6 +21,7 @@
 #include <mach/cpu.h>
 #include <mach/at91_dbgu.h>
 #include <mach/at91sam9260.h>
+#include <mach/hardware.h>
 
 #include "at91_aic.h"
 #include "at91_rstc.h"
diff --git a/arch/arm/mach-at91/at91sam9260_devices.c b/arch/arm/mach-at91/at91sam9260_devices.c
index eda8d16..2ae7715 100644
--- a/arch/arm/mach-at91/at91sam9260_devices.c
+++ b/arch/arm/mach-at91/at91sam9260_devices.c
@@ -25,6 +25,7 @@
 #include <mach/at91_matrix.h>
 #include <mach/at91sam9_smc.h>
 #include <mach/at91_adc.h>
+#include <mach/hardware.h>
 
 #include "board.h"
 #include "generic.h"
@@ -819,6 +820,7 @@
 static struct atmel_uart_data dbgu_data = {
 	.use_dma_tx	= 0,
 	.use_dma_rx	= 0,		/* DBGU not capable of receive DMA */
+	.rts_gpio	= -EINVAL,
 };
 
 static u64 dbgu_dmamask = DMA_BIT_MASK(32);
@@ -857,6 +859,7 @@
 static struct atmel_uart_data uart0_data = {
 	.use_dma_tx	= 1,
 	.use_dma_rx	= 1,
+	.rts_gpio	= -EINVAL,
 };
 
 static u64 uart0_dmamask = DMA_BIT_MASK(32);
@@ -908,6 +911,7 @@
 static struct atmel_uart_data uart1_data = {
 	.use_dma_tx	= 1,
 	.use_dma_rx	= 1,
+	.rts_gpio	= -EINVAL,
 };
 
 static u64 uart1_dmamask = DMA_BIT_MASK(32);
@@ -951,6 +955,7 @@
 static struct atmel_uart_data uart2_data = {
 	.use_dma_tx	= 1,
 	.use_dma_rx	= 1,
+	.rts_gpio	= -EINVAL,
 };
 
 static u64 uart2_dmamask = DMA_BIT_MASK(32);
@@ -994,6 +999,7 @@
 static struct atmel_uart_data uart3_data = {
 	.use_dma_tx	= 1,
 	.use_dma_rx	= 1,
+	.rts_gpio	= -EINVAL,
 };
 
 static u64 uart3_dmamask = DMA_BIT_MASK(32);
@@ -1037,6 +1043,7 @@
 static struct atmel_uart_data uart4_data = {
 	.use_dma_tx	= 1,
 	.use_dma_rx	= 1,
+	.rts_gpio	= -EINVAL,
 };
 
 static u64 uart4_dmamask = DMA_BIT_MASK(32);
@@ -1075,6 +1082,7 @@
 static struct atmel_uart_data uart5_data = {
 	.use_dma_tx	= 1,
 	.use_dma_rx	= 1,
+	.rts_gpio	= -EINVAL,
 };
 
 static u64 uart5_dmamask = DMA_BIT_MASK(32);
diff --git a/arch/arm/mach-at91/at91sam9261.c b/arch/arm/mach-at91/at91sam9261.c
index 6276b4c..48b51f7 100644
--- a/arch/arm/mach-at91/at91sam9261.c
+++ b/arch/arm/mach-at91/at91sam9261.c
@@ -20,6 +20,7 @@
 #include <asm/system_misc.h>
 #include <mach/cpu.h>
 #include <mach/at91sam9261.h>
+#include <mach/hardware.h>
 
 #include "at91_aic.h"
 #include "at91_rstc.h"
diff --git a/arch/arm/mach-at91/at91sam9261_devices.c b/arch/arm/mach-at91/at91sam9261_devices.c
index b2a3474..80e3589 100644
--- a/arch/arm/mach-at91/at91sam9261_devices.c
+++ b/arch/arm/mach-at91/at91sam9261_devices.c
@@ -25,6 +25,7 @@
 #include <mach/at91sam9261_matrix.h>
 #include <mach/at91_matrix.h>
 #include <mach/at91sam9_smc.h>
+#include <mach/hardware.h>
 
 #include "board.h"
 #include "generic.h"
@@ -880,6 +881,7 @@
 static struct atmel_uart_data dbgu_data = {
 	.use_dma_tx	= 0,
 	.use_dma_rx	= 0,		/* DBGU not capable of receive DMA */
+	.rts_gpio	= -EINVAL,
 };
 
 static u64 dbgu_dmamask = DMA_BIT_MASK(32);
@@ -918,6 +920,7 @@
 static struct atmel_uart_data uart0_data = {
 	.use_dma_tx	= 1,
 	.use_dma_rx	= 1,
+	.rts_gpio	= -EINVAL,
 };
 
 static u64 uart0_dmamask = DMA_BIT_MASK(32);
@@ -961,6 +964,7 @@
 static struct atmel_uart_data uart1_data = {
 	.use_dma_tx	= 1,
 	.use_dma_rx	= 1,
+	.rts_gpio	= -EINVAL,
 };
 
 static u64 uart1_dmamask = DMA_BIT_MASK(32);
@@ -1004,6 +1008,7 @@
 static struct atmel_uart_data uart2_data = {
 	.use_dma_tx	= 1,
 	.use_dma_rx	= 1,
+	.rts_gpio	= -EINVAL,
 };
 
 static u64 uart2_dmamask = DMA_BIT_MASK(32);
diff --git a/arch/arm/mach-at91/at91sam9263.c b/arch/arm/mach-at91/at91sam9263.c
index 37b90f4..486530c 100644
--- a/arch/arm/mach-at91/at91sam9263.c
+++ b/arch/arm/mach-at91/at91sam9263.c
@@ -19,6 +19,7 @@
 #include <asm/mach/map.h>
 #include <asm/system_misc.h>
 #include <mach/at91sam9263.h>
+#include <mach/hardware.h>
 
 #include "at91_aic.h"
 #include "at91_rstc.h"
diff --git a/arch/arm/mach-at91/at91sam9263_devices.c b/arch/arm/mach-at91/at91sam9263_devices.c
index 4aeaddd..43d53d6 100644
--- a/arch/arm/mach-at91/at91sam9263_devices.c
+++ b/arch/arm/mach-at91/at91sam9263_devices.c
@@ -24,6 +24,7 @@
 #include <mach/at91sam9263_matrix.h>
 #include <mach/at91_matrix.h>
 #include <mach/at91sam9_smc.h>
+#include <mach/hardware.h>
 
 #include "board.h"
 #include "generic.h"
@@ -1324,6 +1325,7 @@
 static struct atmel_uart_data dbgu_data = {
 	.use_dma_tx	= 0,
 	.use_dma_rx	= 0,		/* DBGU not capable of receive DMA */
+	.rts_gpio	= -EINVAL,
 };
 
 static u64 dbgu_dmamask = DMA_BIT_MASK(32);
@@ -1362,6 +1364,7 @@
 static struct atmel_uart_data uart0_data = {
 	.use_dma_tx	= 1,
 	.use_dma_rx	= 1,
+	.rts_gpio	= -EINVAL,
 };
 
 static u64 uart0_dmamask = DMA_BIT_MASK(32);
@@ -1405,6 +1408,7 @@
 static struct atmel_uart_data uart1_data = {
 	.use_dma_tx	= 1,
 	.use_dma_rx	= 1,
+	.rts_gpio	= -EINVAL,
 };
 
 static u64 uart1_dmamask = DMA_BIT_MASK(32);
@@ -1448,6 +1452,7 @@
 static struct atmel_uart_data uart2_data = {
 	.use_dma_tx	= 1,
 	.use_dma_rx	= 1,
+	.rts_gpio	= -EINVAL,
 };
 
 static u64 uart2_dmamask = DMA_BIT_MASK(32);
diff --git a/arch/arm/mach-at91/at91sam926x_time.c b/arch/arm/mach-at91/at91sam926x_time.c
index 0f04ffe..0a9e2fc 100644
--- a/arch/arm/mach-at91/at91sam926x_time.c
+++ b/arch/arm/mach-at91/at91sam926x_time.c
@@ -19,6 +19,7 @@
 #include <linux/of_irq.h>
 
 #include <asm/mach/time.h>
+#include <mach/hardware.h>
 
 #define AT91_PIT_MR		0x00			/* Mode Register */
 #define		AT91_PIT_PITIEN		(1 << 25)		/* Timer Interrupt Enable */
diff --git a/arch/arm/mach-at91/at91sam9g45.c b/arch/arm/mach-at91/at91sam9g45.c
index 2f455ce..8c11696 100644
--- a/arch/arm/mach-at91/at91sam9g45.c
+++ b/arch/arm/mach-at91/at91sam9g45.c
@@ -20,6 +20,7 @@
 #include <asm/system_misc.h>
 #include <mach/at91sam9g45.h>
 #include <mach/cpu.h>
+#include <mach/hardware.h>
 
 #include "at91_aic.h"
 #include "soc.h"
diff --git a/arch/arm/mach-at91/at91sam9g45_devices.c b/arch/arm/mach-at91/at91sam9g45_devices.c
index cb36fa8..77b04c2 100644
--- a/arch/arm/mach-at91/at91sam9g45_devices.c
+++ b/arch/arm/mach-at91/at91sam9g45_devices.c
@@ -32,6 +32,7 @@
 #include <mach/at91sam9_smc.h>
 #include <linux/platform_data/dma-atmel.h>
 #include <mach/atmel-mci.h>
+#include <mach/hardware.h>
 
 #include <media/atmel-isi.h>
 
@@ -1587,6 +1588,7 @@
 static struct atmel_uart_data dbgu_data = {
 	.use_dma_tx	= 0,
 	.use_dma_rx	= 0,
+	.rts_gpio	= -EINVAL,
 };
 
 static u64 dbgu_dmamask = DMA_BIT_MASK(32);
@@ -1625,6 +1627,7 @@
 static struct atmel_uart_data uart0_data = {
 	.use_dma_tx	= 1,
 	.use_dma_rx	= 1,
+	.rts_gpio	= -EINVAL,
 };
 
 static u64 uart0_dmamask = DMA_BIT_MASK(32);
@@ -1668,6 +1671,7 @@
 static struct atmel_uart_data uart1_data = {
 	.use_dma_tx	= 1,
 	.use_dma_rx	= 1,
+	.rts_gpio	= -EINVAL,
 };
 
 static u64 uart1_dmamask = DMA_BIT_MASK(32);
@@ -1711,6 +1715,7 @@
 static struct atmel_uart_data uart2_data = {
 	.use_dma_tx	= 1,
 	.use_dma_rx	= 1,
+	.rts_gpio	= -EINVAL,
 };
 
 static u64 uart2_dmamask = DMA_BIT_MASK(32);
@@ -1754,6 +1759,7 @@
 static struct atmel_uart_data uart3_data = {
 	.use_dma_tx	= 1,
 	.use_dma_rx	= 1,
+	.rts_gpio	= -EINVAL,
 };
 
 static u64 uart3_dmamask = DMA_BIT_MASK(32);
diff --git a/arch/arm/mach-at91/at91sam9rl.c b/arch/arm/mach-at91/at91sam9rl.c
index 3651517..c0d5474 100644
--- a/arch/arm/mach-at91/at91sam9rl.c
+++ b/arch/arm/mach-at91/at91sam9rl.c
@@ -20,6 +20,7 @@
 #include <mach/cpu.h>
 #include <mach/at91_dbgu.h>
 #include <mach/at91sam9rl.h>
+#include <mach/hardware.h>
 
 #include "at91_aic.h"
 #include "at91_rstc.h"
diff --git a/arch/arm/mach-at91/at91sam9rl_devices.c b/arch/arm/mach-at91/at91sam9rl_devices.c
index a698bda..428fc41 100644
--- a/arch/arm/mach-at91/at91sam9rl_devices.c
+++ b/arch/arm/mach-at91/at91sam9rl_devices.c
@@ -21,6 +21,7 @@
 #include <mach/at91sam9rl_matrix.h>
 #include <mach/at91_matrix.h>
 #include <mach/at91sam9_smc.h>
+#include <mach/hardware.h>
 #include <linux/platform_data/dma-atmel.h>
 
 #include "board.h"
@@ -956,6 +957,7 @@
 static struct atmel_uart_data dbgu_data = {
 	.use_dma_tx	= 0,
 	.use_dma_rx	= 0,		/* DBGU not capable of receive DMA */
+	.rts_gpio	= -EINVAL,
 };
 
 static u64 dbgu_dmamask = DMA_BIT_MASK(32);
@@ -994,6 +996,7 @@
 static struct atmel_uart_data uart0_data = {
 	.use_dma_tx	= 1,
 	.use_dma_rx	= 1,
+	.rts_gpio	= -EINVAL,
 };
 
 static u64 uart0_dmamask = DMA_BIT_MASK(32);
@@ -1045,6 +1048,7 @@
 static struct atmel_uart_data uart1_data = {
 	.use_dma_tx	= 1,
 	.use_dma_rx	= 1,
+	.rts_gpio	= -EINVAL,
 };
 
 static u64 uart1_dmamask = DMA_BIT_MASK(32);
@@ -1088,6 +1092,7 @@
 static struct atmel_uart_data uart2_data = {
 	.use_dma_tx	= 1,
 	.use_dma_rx	= 1,
+	.rts_gpio	= -EINVAL,
 };
 
 static u64 uart2_dmamask = DMA_BIT_MASK(32);
@@ -1131,6 +1136,7 @@
 static struct atmel_uart_data uart3_data = {
 	.use_dma_tx	= 1,
 	.use_dma_rx	= 1,
+	.rts_gpio	= -EINVAL,
 };
 
 static u64 uart3_dmamask = DMA_BIT_MASK(32);
diff --git a/arch/arm/mach-at91/at91x40.c b/arch/arm/mach-at91/at91x40.c
index bad94b8..7523f1c 100644
--- a/arch/arm/mach-at91/at91x40.c
+++ b/arch/arm/mach-at91/at91x40.c
@@ -19,7 +19,7 @@
 #include <asm/mach/arch.h>
 #include <mach/at91x40.h>
 #include <mach/at91_st.h>
-#include <mach/timex.h>
+#include <mach/hardware.h>
 
 #include "at91_aic.h"
 #include "generic.h"
diff --git a/arch/arm/mach-at91/at91x40_time.c b/arch/arm/mach-at91/at91x40_time.c
index c0e637a..07d0bf2 100644
--- a/arch/arm/mach-at91/at91x40_time.c
+++ b/arch/arm/mach-at91/at91x40_time.c
@@ -25,6 +25,7 @@
 #include <linux/time.h>
 #include <linux/io.h>
 #include <mach/hardware.h>
+#include <mach/at91x40.h>
 #include <asm/mach/time.h>
 
 #include "at91_tc.h"
diff --git a/arch/arm/mach-at91/board-gsia18s.c b/arch/arm/mach-at91/board-gsia18s.c
index c1d61d2..416bae8 100644
--- a/arch/arm/mach-at91/board-gsia18s.c
+++ b/arch/arm/mach-at91/board-gsia18s.c
@@ -31,6 +31,7 @@
 #include <asm/mach/arch.h>
 
 #include <mach/at91sam9_smc.h>
+#include <mach/hardware.h>
 
 #include "at91_aic.h"
 #include "board.h"
diff --git a/arch/arm/mach-at91/board-pcontrol-g20.c b/arch/arm/mach-at91/board-pcontrol-g20.c
index 65c0d6b..5f25fa5 100644
--- a/arch/arm/mach-at91/board-pcontrol-g20.c
+++ b/arch/arm/mach-at91/board-pcontrol-g20.c
@@ -30,6 +30,7 @@
 #include <asm/mach/arch.h>
 
 #include <mach/at91sam9_smc.h>
+#include <mach/hardware.h>
 
 #include "at91_aic.h"
 #include "board.h"
diff --git a/arch/arm/mach-at91/board-stamp9g20.c b/arch/arm/mach-at91/board-stamp9g20.c
index 869cbec..e4a5ac1 100644
--- a/arch/arm/mach-at91/board-stamp9g20.c
+++ b/arch/arm/mach-at91/board-stamp9g20.c
@@ -26,6 +26,7 @@
 #include <asm/mach/arch.h>
 
 #include <mach/at91sam9_smc.h>
+#include <mach/hardware.h>
 
 #include "at91_aic.h"
 #include "board.h"
diff --git a/arch/arm/mach-at91/include/mach/at91x40.h b/arch/arm/mach-at91/include/mach/at91x40.h
index 9068021..38dca2b 100644
--- a/arch/arm/mach-at91/include/mach/at91x40.h
+++ b/arch/arm/mach-at91/include/mach/at91x40.h
@@ -55,4 +55,6 @@
 #define	AT91_PS_CR	(AT91_PS + 0)	/* PS Control register */
 #define	AT91_PS_CR_CPU	(1 << 0)	/* CPU clock disable bit */
 
+#define AT91X40_MASTER_CLOCK	40000000
+
 #endif /* AT91X40_H */
diff --git a/arch/arm/mach-at91/include/mach/timex.h b/arch/arm/mach-at91/include/mach/timex.h
deleted file mode 100644
index 5e917a6..0000000
--- a/arch/arm/mach-at91/include/mach/timex.h
+++ /dev/null
@@ -1,37 +0,0 @@
-/*
- * arch/arm/mach-at91/include/mach/timex.h
- *
- *  Copyright (C) 2003 SAN People
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-
-#ifndef __ASM_ARCH_TIMEX_H
-#define __ASM_ARCH_TIMEX_H
-
-#include <mach/hardware.h>
-
-#ifdef CONFIG_ARCH_AT91X40
-
-#define AT91X40_MASTER_CLOCK	40000000
-#define CLOCK_TICK_RATE		(AT91X40_MASTER_CLOCK)
-
-#else
-
-#define CLOCK_TICK_RATE		12345678
-
-#endif
-
-#endif /* __ASM_ARCH_TIMEX_H */
diff --git a/arch/arm/mach-at91/pm.c b/arch/arm/mach-at91/pm.c
index 590b52d..8bda1ce 100644
--- a/arch/arm/mach-at91/pm.c
+++ b/arch/arm/mach-at91/pm.c
@@ -27,6 +27,7 @@
 #include <asm/mach/irq.h>
 
 #include <mach/cpu.h>
+#include <mach/hardware.h>
 
 #include "at91_aic.h"
 #include "generic.h"
diff --git a/arch/arm/mach-bcm/Kconfig b/arch/arm/mach-bcm/Kconfig
index b1aa6a9..af4f2df 100644
--- a/arch/arm/mach-bcm/Kconfig
+++ b/arch/arm/mach-bcm/Kconfig
@@ -16,12 +16,7 @@
 	select ARM_ERRATA_754322
 	select ARM_ERRATA_764369 if SMP
 	select ARM_GIC
-	select CPU_V7
-	select CLKSRC_OF
-	select GENERIC_CLOCKEVENTS
-	select GENERIC_TIME
 	select GPIO_BCM_KONA
-	select SPARSE_IRQ
 	select TICK_ONESHOT
 	select CACHE_L2X0
 	select HAVE_ARM_ARCH_TIMER
diff --git a/arch/arm/mach-bcm2835/Kconfig b/arch/arm/mach-bcm2835/Kconfig
index d1f9612..3a36935 100644
--- a/arch/arm/mach-bcm2835/Kconfig
+++ b/arch/arm/mach-bcm2835/Kconfig
@@ -4,10 +4,6 @@
 	select ARM_AMBA
 	select ARM_ERRATA_411920
 	select ARM_TIMER_SP804
-	select CLKDEV_LOOKUP
-	select CLKSRC_OF
-	select CPU_V6
-	select GENERIC_CLOCKEVENTS
 	select PINCTRL
 	select PINCTRL_BCM2835
 	help
diff --git a/arch/arm/mach-berlin/Kconfig b/arch/arm/mach-berlin/Kconfig
index 7a02d22..b0cb072 100644
--- a/arch/arm/mach-berlin/Kconfig
+++ b/arch/arm/mach-berlin/Kconfig
@@ -1,9 +1,7 @@
 config ARCH_BERLIN
 	bool "Marvell Berlin SoCs" if ARCH_MULTI_V7
 	select ARM_GIC
-	select GENERIC_CLOCKEVENTS
 	select GENERIC_IRQ_CHIP
-	select COMMON_CLK
 	select DW_APB_ICTL
 	select DW_APB_TIMER_OF
 
@@ -16,12 +14,10 @@
 	select CACHE_L2X0
 	select CPU_PJ4B
 	select HAVE_ARM_TWD if SMP
-	select HAVE_SMP
 
 config MACH_BERLIN_BG2CD
 	bool "Marvell Armada 1500-mini (BG2CD)"
 	select CACHE_L2X0
-	select CPU_V7
 	select HAVE_ARM_TWD if SMP
 
 endmenu
diff --git a/arch/arm/mach-clps711x/Kconfig b/arch/arm/mach-clps711x/Kconfig
index bea6295..f711498 100644
--- a/arch/arm/mach-clps711x/Kconfig
+++ b/arch/arm/mach-clps711x/Kconfig
@@ -33,20 +33,6 @@
 	  Say Y here if you intend to run this kernel on the ARM Prospector
 	  720T.
 
-config EP72XX_ROM_BOOT
-	bool "EP721x/EP731x ROM boot"
-	help
-	  If you say Y here, your CLPS711x-based kernel will use the bootstrap
-	  mode memory map instead of the normal memory map.
-
-	  Processors derived from the Cirrus CLPS711X core support two boot
-	  modes.  Normal mode boots from the external memory device at CS0.
-	  Bootstrap mode rearranges parts of the memory map, placing an
-	  internal 128 byte bootstrap ROM at CS0.  This option performs the
-	  address map changes required to support booting in this mode.
-
-	  You almost surely want to say N here.
-
 endmenu
 
 endif
diff --git a/arch/arm/mach-clps711x/include/mach/hardware.h b/arch/arm/mach-clps711x/include/mach/hardware.h
index c5a8ea6..5d6afda 100644
--- a/arch/arm/mach-clps711x/include/mach/hardware.h
+++ b/arch/arm/mach-clps711x/include/mach/hardware.h
@@ -38,13 +38,6 @@
 #define clps_writel(val,off)	writel(val, CLPS711X_VIRT_BASE + (off))
 #endif
 
-/*
- * The physical addresses that the external chip select signals map to is
- * dependent on the setting of the nMEDCHG signal on EP7211 and EP7212
- * processors.  CONFIG_EP72XX_BOOT_ROM is only available if these
- * processors are in use.
- */
-#ifndef CONFIG_EP72XX_ROM_BOOT
 #define CS0_PHYS_BASE		(0x00000000)
 #define CS1_PHYS_BASE		(0x10000000)
 #define CS2_PHYS_BASE		(0x20000000)
@@ -53,16 +46,6 @@
 #define CS5_PHYS_BASE		(0x50000000)
 #define CS6_PHYS_BASE		(0x60000000)
 #define CS7_PHYS_BASE		(0x70000000)
-#else
-#define CS0_PHYS_BASE		(0x70000000)
-#define CS1_PHYS_BASE		(0x60000000)
-#define CS2_PHYS_BASE		(0x50000000)
-#define CS3_PHYS_BASE		(0x40000000)
-#define CS4_PHYS_BASE		(0x30000000)
-#define CS5_PHYS_BASE		(0x20000000)
-#define CS6_PHYS_BASE		(0x10000000)
-#define CS7_PHYS_BASE		(0x00000000)
-#endif
 
 #define CLPS711X_SRAM_BASE	CS6_PHYS_BASE
 #define CLPS711X_SRAM_SIZE	(48 * 1024)
diff --git a/arch/arm/mach-clps711x/include/mach/timex.h b/arch/arm/mach-clps711x/include/mach/timex.h
deleted file mode 100644
index de6fd19..0000000
--- a/arch/arm/mach-clps711x/include/mach/timex.h
+++ /dev/null
@@ -1,2 +0,0 @@
-/* Bogus value */
-#define CLOCK_TICK_RATE 512000
diff --git a/arch/arm/mach-cns3xxx/Kconfig b/arch/arm/mach-cns3xxx/Kconfig
index dbf0df8..dce8dec 100644
--- a/arch/arm/mach-cns3xxx/Kconfig
+++ b/arch/arm/mach-cns3xxx/Kconfig
@@ -1,9 +1,6 @@
 config ARCH_CNS3XXX
 	bool "Cavium Networks CNS3XXX family" if ARCH_MULTI_V6
 	select ARM_GIC
-	select CPU_V6K
-	select GENERIC_CLOCKEVENTS
-	select MIGHT_HAVE_CACHE_L2X0
 	select MIGHT_HAVE_PCI
 	select PCI_DOMAINS if PCI
 	help
diff --git a/arch/arm/mach-davinci/include/mach/timex.h b/arch/arm/mach-davinci/include/mach/timex.h
deleted file mode 100644
index 9b88529..0000000
--- a/arch/arm/mach-davinci/include/mach/timex.h
+++ /dev/null
@@ -1,22 +0,0 @@
-/*
- * DaVinci timer defines
- *
- * Author: Kevin Hilman, MontaVista Software, Inc. <source@mvista.com>
- *
- * 2007 (c) MontaVista Software, Inc. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
- */
-#ifndef __ASM_ARCH_TIMEX_H
-#define __ASM_ARCH_TIMEX_H
-
-/*
- * Alert: Not all timers of the DaVinci family run at a frequency of 27MHz,
- * but we should be fine as long as CLOCK_TICK_RATE or LATCH (see include/
- * linux/jiffies.h) are not used directly in code. Currently none of the
- * code relevant to DaVinci platform depends on these values directly.
- */
-#define CLOCK_TICK_RATE 27000000
-
-#endif /* __ASM_ARCH_TIMEX_H__ */
diff --git a/arch/arm/mach-dove/include/mach/timex.h b/arch/arm/mach-dove/include/mach/timex.h
deleted file mode 100644
index 251d538..0000000
--- a/arch/arm/mach-dove/include/mach/timex.h
+++ /dev/null
@@ -1,9 +0,0 @@
-/*
- * arch/arm/mach-dove/include/mach/timex.h
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#define CLOCK_TICK_RATE		(100 * HZ)
diff --git a/arch/arm/mach-ebsa110/include/mach/timex.h b/arch/arm/mach-ebsa110/include/mach/timex.h
deleted file mode 100644
index 4fb43b2..0000000
--- a/arch/arm/mach-ebsa110/include/mach/timex.h
+++ /dev/null
@@ -1,19 +0,0 @@
-/*
- *  arch/arm/mach-ebsa110/include/mach/timex.h
- *
- *  Copyright (C) 1997, 1998 Russell King
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- *  EBSA110 architecture timex specifications
- */
-
-/*
- * On the EBSA, the clock ticks at weird rates.
- * This is therefore not used to calculate the
- * divisor.
- */
-#define CLOCK_TICK_RATE		47894000
-
diff --git a/arch/arm/mach-efm32/include/mach/entry-macro.S b/arch/arm/mach-efm32/include/mach/entry-macro.S
deleted file mode 100644
index 322159d..0000000
--- a/arch/arm/mach-efm32/include/mach/entry-macro.S
+++ /dev/null
@@ -1,4 +0,0 @@
-/*
- * Empty file waiting for deletion once <mach/entry-macro.S> isn't needed any
- * more. Patch "ARM: v7-M: drop using mach/entry-macro.S" sitting in next.
- */
diff --git a/arch/arm/mach-efm32/include/mach/timex.h b/arch/arm/mach-efm32/include/mach/timex.h
deleted file mode 100644
index 7a8b26d..0000000
--- a/arch/arm/mach-efm32/include/mach/timex.h
+++ /dev/null
@@ -1,3 +0,0 @@
-/*
- * Empty file waiting for deletion once <mach/timex.h> isn't needed any more.
- */
diff --git a/arch/arm/mach-ep93xx/core.c b/arch/arm/mach-ep93xx/core.c
index 157ba88..6c70547 100644
--- a/arch/arm/mach-ep93xx/core.c
+++ b/arch/arm/mach-ep93xx/core.c
@@ -117,7 +117,7 @@
 #define EP93XX_TIMER4_CLOCK		983040
 
 #define TIMER1_RELOAD			((EP93XX_TIMER123_CLOCK / HZ) - 1)
-#define TIMER4_TICKS_PER_JIFFY		DIV_ROUND_CLOSEST(CLOCK_TICK_RATE, HZ)
+#define TIMER4_TICKS_PER_JIFFY		DIV_ROUND_CLOSEST(EP93XX_TIMER4_CLOCK, HZ)
 
 static unsigned int last_jiffy_time;
 
diff --git a/arch/arm/mach-ep93xx/include/mach/timex.h b/arch/arm/mach-ep93xx/include/mach/timex.h
deleted file mode 100644
index 6b3503b..0000000
--- a/arch/arm/mach-ep93xx/include/mach/timex.h
+++ /dev/null
@@ -1,5 +0,0 @@
-/*
- * arch/arm/mach-ep93xx/include/mach/timex.h
- */
-
-#define CLOCK_TICK_RATE		983040
diff --git a/arch/arm/mach-exynos/common.c b/arch/arm/mach-exynos/common.c
index f18be40..025fd82 100644
--- a/arch/arm/mach-exynos/common.c
+++ b/arch/arm/mach-exynos/common.c
@@ -20,6 +20,7 @@
 #include <clocksource/samsung_pwm.h>
 #include <linux/sched.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 #include <linux/of.h>
 #include <linux/of_fdt.h>
 #include <linux/of_irq.h>
@@ -40,7 +41,6 @@
 
 #include <plat/cpu.h>
 #include <plat/pm.h>
-#include <plat/regs-serial.h>
 
 #include "common.h"
 #include "regs-pmu.h"
diff --git a/arch/arm/mach-exynos/include/mach/timex.h b/arch/arm/mach-exynos/include/mach/timex.h
deleted file mode 100644
index 6d13875..0000000
--- a/arch/arm/mach-exynos/include/mach/timex.h
+++ /dev/null
@@ -1,29 +0,0 @@
-/* linux/arch/arm/mach-exynos4/include/mach/timex.h
- *
- * Copyright (c) 2010-2011 Samsung Electronics Co., Ltd.
- *		http://www.samsung.com
- *
- * Copyright (c) 2003-2010 Simtec Electronics
- *	Ben Dooks <ben@simtec.co.uk>
- *
- * Based on arch/arm/mach-s5p6442/include/mach/timex.h
- *
- * EXYNOS4 - time parameters
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#ifndef __ASM_ARCH_TIMEX_H
-#define __ASM_ARCH_TIMEX_H __FILE__
-
-/* CLOCK_TICK_RATE needs to be evaluatable by the cpp, so making it
- * a variable is useless. It seems as long as we make our timers an
- * exact multiple of HZ, any value that makes a 1->1 correspondence
- * for the time conversion functions to/from jiffies is acceptable.
-*/
-
-#define CLOCK_TICK_RATE 12000000
-
-#endif /* __ASM_ARCH_TIMEX_H */
diff --git a/arch/arm/mach-exynos/include/mach/uncompress.h b/arch/arm/mach-exynos/include/mach/uncompress.h
deleted file mode 100644
index 5d7ce36..0000000
--- a/arch/arm/mach-exynos/include/mach/uncompress.h
+++ /dev/null
@@ -1,48 +0,0 @@
-/*
- * Copyright (c) 2010-2012 Samsung Electronics Co., Ltd.
- *		http://www.samsung.com
- *
- * EXYNOS - uncompress code
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#ifndef __ASM_ARCH_UNCOMPRESS_H
-#define __ASM_ARCH_UNCOMPRESS_H __FILE__
-
-#include <asm/mach-types.h>
-
-#include <mach/map.h>
-#include <plat/uncompress.h>
-
-static unsigned int __raw_readl(unsigned int ptr)
-{
-	return *((volatile unsigned int *)ptr);
-}
-
-static void arch_detect_cpu(void)
-{
-	u32 chip_id = __raw_readl(EXYNOS_PA_CHIPID);
-
-	/*
-	 * product_id is bits 31:12
-	 * bits 23:20 describe the exynosX family
-	 * bits 27:24 describe the exynosX family in exynos5420
-	 */
-	chip_id >>= 20;
-
-	if ((chip_id & 0x0f) == 0x5 || (chip_id & 0xf0) == 0x50)
-		uart_base = (volatile u8 *)EXYNOS5_PA_UART + (S3C_UART_OFFSET * CONFIG_S3C_LOWLEVEL_UART_PORT);
-	else
-		uart_base = (volatile u8 *)EXYNOS4_PA_UART + (S3C_UART_OFFSET * CONFIG_S3C_LOWLEVEL_UART_PORT);
-
-	/*
-	 * For preventing FIFO overrun or infinite loop of UART console,
-	 * fifo_max should be the minimum fifo size of all of the UART channels
-	 */
-	fifo_mask = S5PV210_UFSTAT_TXMASK;
-	fifo_max = 15 << S5PV210_UFSTAT_TXSHIFT;
-}
-#endif /* __ASM_ARCH_UNCOMPRESS_H */
diff --git a/arch/arm/mach-exynos/pm_domains.c b/arch/arm/mach-exynos/pm_domains.c
index 8fd2488..fe6570e 100644
--- a/arch/arm/mach-exynos/pm_domains.c
+++ b/arch/arm/mach-exynos/pm_domains.c
@@ -22,8 +22,6 @@
 #include <linux/of_platform.h>
 #include <linux/sched.h>
 
-#include <plat/devs.h>
-
 #include "regs-pmu.h"
 
 /*
diff --git a/arch/arm/mach-footbridge/include/mach/timex.h b/arch/arm/mach-footbridge/include/mach/timex.h
deleted file mode 100644
index d0fea9d..0000000
--- a/arch/arm/mach-footbridge/include/mach/timex.h
+++ /dev/null
@@ -1,18 +0,0 @@
-/*
- *  arch/arm/mach-footbridge/include/mach/timex.h
- *
- *  Copyright (C) 1998 Russell King
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- *  EBSA285 architecture timex specifications
- */
-
-/*
- * We assume a constant here; this satisfies the maths in linux/timex.h
- * and linux/time.h.  CLOCK_TICK_RATE is actually system dependent, but
- * this must be a constant.
- */
-#define CLOCK_TICK_RATE		(50000000/16)
diff --git a/arch/arm/mach-gemini/include/mach/timex.h b/arch/arm/mach-gemini/include/mach/timex.h
deleted file mode 100644
index dc5690b..0000000
--- a/arch/arm/mach-gemini/include/mach/timex.h
+++ /dev/null
@@ -1,13 +0,0 @@
-/*
- * Gemini timex specifications
- *
- * Copyright (C) 2008-2009 Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- */
-
-/* When AHB bus frequency is 150MHz */
-#define CLOCK_TICK_RATE	38000000
diff --git a/arch/arm/mach-highbank/Kconfig b/arch/arm/mach-highbank/Kconfig
index 0aded64..830b76e 100644
--- a/arch/arm/mach-highbank/Kconfig
+++ b/arch/arm/mach-highbank/Kconfig
@@ -5,7 +5,6 @@
 	select ARCH_HAS_HOLES_MEMORYMODEL
 	select ARCH_HAS_OPP
 	select ARCH_SUPPORTS_BIG_ENDIAN
-	select ARCH_WANT_OPTIONAL_GPIOLIB
 	select ARM_AMBA
 	select ARM_ERRATA_764369 if SMP
 	select ARM_ERRATA_775420
@@ -14,14 +13,8 @@
 	select ARM_PSCI
 	select ARM_TIMER_SP804
 	select CACHE_L2X0
-	select COMMON_CLK
-	select CPU_V7
-	select GENERIC_CLOCKEVENTS
 	select HAVE_ARM_SCU
 	select HAVE_ARM_TWD if SMP
-	select HAVE_SMP
 	select MAILBOX
 	select PL320_MBOX
-	select SPARSE_IRQ
-	select USE_OF
 	select ZONE_DMA if ARM_LPAE
diff --git a/arch/arm/mach-hisi/Kconfig b/arch/arm/mach-hisi/Kconfig
index 1abae5f..9d0a87b 100644
--- a/arch/arm/mach-hisi/Kconfig
+++ b/arch/arm/mach-hisi/Kconfig
@@ -3,13 +3,9 @@
 	select ARM_AMBA
 	select ARM_GIC
 	select ARM_TIMER_SP804
-	select ARCH_WANT_OPTIONAL_GPIOLIB
 	select CACHE_L2X0
-	select CLKSRC_OF
-	select GENERIC_CLOCKEVENTS
 	select HAVE_ARM_SCU
 	select HAVE_ARM_TWD if SMP
-	select HAVE_SMP
 	select PINCTRL
 	select PINCTRL_SINGLE
 	help
diff --git a/arch/arm/mach-imx/Kconfig b/arch/arm/mach-imx/Kconfig
index 33567aa..41ffd43 100644
--- a/arch/arm/mach-imx/Kconfig
+++ b/arch/arm/mach-imx/Kconfig
@@ -2,18 +2,11 @@
 	bool "Freescale i.MX family" if ARCH_MULTI_V4_V5 || ARCH_MULTI_V6_V7
 	select ARCH_REQUIRE_GPIOLIB
 	select ARM_CPU_SUSPEND if PM
-	select ARM_PATCH_PHYS_VIRT
 	select CLKSRC_MMIO
-	select COMMON_CLK
 	select GENERIC_ALLOCATOR
-	select GENERIC_CLOCKEVENTS
 	select GENERIC_IRQ_CHIP
-	select MIGHT_HAVE_CACHE_L2X0 if ARCH_MULTI_V6_V7
-	select MULTI_IRQ_HANDLER
 	select PINCTRL
 	select SOC_BUS
-	select SPARSE_IRQ
-	select USE_OF
 	help
 	  Support for Freescale MXC/iMX-based family of processors
 
@@ -121,7 +114,6 @@
 config SOC_IMX35
 	bool
 	select ARCH_MXC_IOMUX_V3
-	select CPU_V6K
 	select HAVE_EPIT
 	select MXC_AVIC
 	select SMP_ON_UP if SMP
@@ -132,7 +124,6 @@
 	select ARCH_HAS_CPUFREQ
 	select ARCH_HAS_OPP
 	select ARCH_MXC_IOMUX_V3
-	select CPU_V7
 	select MXC_TZIC
 
 config	SOC_IMX51
@@ -792,14 +783,12 @@
 	select ARM_ERRATA_764369 if SMP
 	select ARM_ERRATA_775420
 	select ARM_GIC
-	select CPU_V7
 	select HAVE_ARM_SCU if SMP
 	select HAVE_ARM_TWD if SMP
 	select HAVE_IMX_ANATOP
 	select HAVE_IMX_GPC
 	select HAVE_IMX_MMDC
 	select HAVE_IMX_SRC
-	select HAVE_SMP
 	select MFD_SYSCON
 	select MIGHT_HAVE_PCI
 	select PCI_DOMAINS if PCI
@@ -817,7 +806,6 @@
 	select ARM_ERRATA_754322
 	select ARM_ERRATA_775420
 	select ARM_GIC
-	select CPU_V7
 	select HAVE_IMX_ANATOP
 	select HAVE_IMX_GPC
 	select HAVE_IMX_MMDC
@@ -833,9 +821,7 @@
 
 config SOC_VF610
 	bool "Vybrid Family VF610 support"
-	select CPU_V7
 	select ARM_GIC
-	select CLKSRC_OF
 	select PINCTRL_VF610
 	select VF_PIT_TIMER
 	select PL310_ERRATA_588369 if CACHE_PL310
diff --git a/arch/arm/mach-integrator/include/mach/timex.h b/arch/arm/mach-integrator/include/mach/timex.h
deleted file mode 100644
index 1dcb420..0000000
--- a/arch/arm/mach-integrator/include/mach/timex.h
+++ /dev/null
@@ -1,26 +0,0 @@
-/*
- *  arch/arm/mach-integrator/include/mach/timex.h
- *
- *  Integrator architecture timex specifications
- *
- *  Copyright (C) 1999 ARM Limited
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-
-/*
- * ??
- */
-#define CLOCK_TICK_RATE		(50000000 / 16)
diff --git a/arch/arm/mach-iop13xx/include/mach/timex.h b/arch/arm/mach-iop13xx/include/mach/timex.h
deleted file mode 100644
index 45fb274..0000000
--- a/arch/arm/mach-iop13xx/include/mach/timex.h
+++ /dev/null
@@ -1 +0,0 @@
-#define CLOCK_TICK_RATE (100 * HZ)
diff --git a/arch/arm/mach-iop32x/include/mach/timex.h b/arch/arm/mach-iop32x/include/mach/timex.h
deleted file mode 100644
index 7262ab8..0000000
--- a/arch/arm/mach-iop32x/include/mach/timex.h
+++ /dev/null
@@ -1,6 +0,0 @@
-/*
- * arch/arm/mach-iop32x/include/mach/timex.h
- *
- * IOP32x architecture timex specifications
- */
-#define CLOCK_TICK_RATE		(100 * HZ)
diff --git a/arch/arm/mach-iop33x/include/mach/timex.h b/arch/arm/mach-iop33x/include/mach/timex.h
deleted file mode 100644
index 54c5890..0000000
--- a/arch/arm/mach-iop33x/include/mach/timex.h
+++ /dev/null
@@ -1,6 +0,0 @@
-/*
- * arch/arm/mach-iop33x/include/mach/timex.h
- *
- * IOP3xx architecture timex specifications
- */
-#define CLOCK_TICK_RATE		(100 * HZ)
diff --git a/arch/arm/mach-ixp4xx/common.c b/arch/arm/mach-ixp4xx/common.c
index 6d68aed..dc5d7a0 100644
--- a/arch/arm/mach-ixp4xx/common.c
+++ b/arch/arm/mach-ixp4xx/common.c
@@ -23,7 +23,6 @@
 #include <linux/interrupt.h>
 #include <linux/bitops.h>
 #include <linux/time.h>
-#include <linux/timex.h>
 #include <linux/clocksource.h>
 #include <linux/clockchips.h>
 #include <linux/io.h>
@@ -45,6 +44,17 @@
 #include <asm/mach/irq.h>
 #include <asm/mach/time.h>
 
+#define IXP4XX_TIMER_FREQ 66666000
+
+/*
+ * The timer register doesn't allow to specify the two least significant bits of
+ * the timeout value and assumes them being zero. So make sure IXP4XX_LATCH is
+ * the best value with the two least significant bits unset.
+ */
+#define IXP4XX_LATCH DIV_ROUND_CLOSEST(IXP4XX_TIMER_FREQ, \
+				       (IXP4XX_OST_RELOAD_MASK + 1) * HZ) * \
+			(IXP4XX_OST_RELOAD_MASK + 1)
+
 static void __init ixp4xx_clocksource_init(void);
 static void __init ixp4xx_clockevent_init(void);
 static struct clock_event_device clockevent_ixp4xx;
@@ -520,7 +530,7 @@
 
 	switch (mode) {
 	case CLOCK_EVT_MODE_PERIODIC:
-		osrt = LATCH & ~IXP4XX_OST_RELOAD_MASK;
+		osrt = IXP4XX_LATCH & ~IXP4XX_OST_RELOAD_MASK;
  		opts = IXP4XX_OST_ENABLE;
 		break;
 	case CLOCK_EVT_MODE_ONESHOT:
diff --git a/arch/arm/mach-ixp4xx/include/mach/timex.h b/arch/arm/mach-ixp4xx/include/mach/timex.h
deleted file mode 100644
index 0396d89..0000000
--- a/arch/arm/mach-ixp4xx/include/mach/timex.h
+++ /dev/null
@@ -1,16 +0,0 @@
-/*
- * arch/arm/mach-ixp4xx/include/mach/timex.h
- * 
- */
-
-#include <mach/ixp4xx-regs.h>
-
-/*
- * We use IXP425 General purpose timer for our timer needs, it runs at 
- * 66.66... MHz. We do a convulted calculation of CLOCK_TICK_RATE b/c the
- * timer register ignores the bottom 2 bits of the LATCH value.
- */
-#define IXP4XX_TIMER_FREQ 66666000
-#define CLOCK_TICK_RATE \
-	(((IXP4XX_TIMER_FREQ / HZ & ~IXP4XX_OST_RELOAD_MASK) + 1) * HZ)
-
diff --git a/arch/arm/mach-keystone/Kconfig b/arch/arm/mach-keystone/Kconfig
index 90a708f..f50bc93 100644
--- a/arch/arm/mach-keystone/Kconfig
+++ b/arch/arm/mach-keystone/Kconfig
@@ -1,13 +1,9 @@
 config ARCH_KEYSTONE
 	bool "Texas Instruments Keystone Devices"
 	depends on ARCH_MULTI_V7
-	select CPU_V7
 	select ARM_GIC
 	select HAVE_ARM_ARCH_TIMER
-	select HAVE_SMP
 	select CLKSRC_MMIO
-	select GENERIC_CLOCKEVENTS
-	select ARCH_WANT_OPTIONAL_GPIOLIB
 	select ARM_ERRATA_798181 if SMP
 	select COMMON_CLK_KEYSTONE
 	select ARCH_SUPPORTS_BIG_ENDIAN
diff --git a/arch/arm/mach-kirkwood/include/mach/timex.h b/arch/arm/mach-kirkwood/include/mach/timex.h
deleted file mode 100644
index c923cd1..0000000
--- a/arch/arm/mach-kirkwood/include/mach/timex.h
+++ /dev/null
@@ -1,10 +0,0 @@
-/*
- * arch/arm/mach-kirkwood/include/mach/timex.h
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#define CLOCK_TICK_RATE		(100 * HZ)
-
diff --git a/arch/arm/mach-ks8695/include/mach/timex.h b/arch/arm/mach-ks8695/include/mach/timex.h
deleted file mode 100644
index 10f7163..0000000
--- a/arch/arm/mach-ks8695/include/mach/timex.h
+++ /dev/null
@@ -1,21 +0,0 @@
-/*
- * arch/arm/mach-ks8695/include/mach/timex.h
- *
- * Copyright (C) 2006 Simtec Electronics
- *	Ben Dooks <ben@simtec.co.uk>
- *
- * KS8695 - Time Parameters
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef __ASM_ARCH_TIMEX_H
-#define __ASM_ARCH_TIMEX_H
-
-#include <mach/hardware.h>
-
-#define CLOCK_TICK_RATE 	KS8695_CLOCK_RATE
-
-#endif
diff --git a/arch/arm/mach-lpc32xx/include/mach/timex.h b/arch/arm/mach-lpc32xx/include/mach/timex.h
deleted file mode 100644
index 8d4066b..0000000
--- a/arch/arm/mach-lpc32xx/include/mach/timex.h
+++ /dev/null
@@ -1,28 +0,0 @@
-/*
- * arch/arm/mach-lpc32xx/include/mach/timex.h
- *
- * Author: Kevin Wells <kevin.wells@nxp.com>
- *
- * Copyright (C) 2010 NXP Semiconductors
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
-
-#ifndef __ASM_ARCH_TIMEX_H
-#define __ASM_ARCH_TIMEX_H
-
-/*
- * Rate in Hz of the main system oscillator. This value should match
- * the value 'MAIN_OSC_FREQ' in platform.h
- */
-#define CLOCK_TICK_RATE	13000000
-
-#endif
diff --git a/arch/arm/mach-mmp/include/mach/timex.h b/arch/arm/mach-mmp/include/mach/timex.h
deleted file mode 100644
index 70c9f1d..0000000
--- a/arch/arm/mach-mmp/include/mach/timex.h
+++ /dev/null
@@ -1,13 +0,0 @@
-/*
- * linux/arch/arm/mach-mmp/include/mach/timex.h
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifdef CONFIG_CPU_MMP2
-#define CLOCK_TICK_RATE		6500000
-#else
-#define CLOCK_TICK_RATE		3250000
-#endif
diff --git a/arch/arm/mach-mmp/time.c b/arch/arm/mach-mmp/time.c
index 024022d..048997e 100644
--- a/arch/arm/mach-mmp/time.c
+++ b/arch/arm/mach-mmp/time.c
@@ -39,6 +39,12 @@
 
 #include "clock.h"
 
+#ifdef CONFIG_CPU_MMP2
+#define MMP_CLOCK_FREQ		6500000
+#else
+#define MMP_CLOCK_FREQ		3250000
+#endif
+
 #define TIMERS_VIRT_BASE	TIMERS1_VIRT_BASE
 
 #define MAX_DELTA		(0xfffffffe)
@@ -195,14 +201,14 @@
 {
 	timer_config();
 
-	sched_clock_register(mmp_read_sched_clock, 32, CLOCK_TICK_RATE);
+	sched_clock_register(mmp_read_sched_clock, 32, MMP_CLOCK_FREQ);
 
 	ckevt.cpumask = cpumask_of(0);
 
 	setup_irq(irq, &timer_irq);
 
-	clocksource_register_hz(&cksrc, CLOCK_TICK_RATE);
-	clockevents_config_and_register(&ckevt, CLOCK_TICK_RATE,
+	clocksource_register_hz(&cksrc, MMP_CLOCK_FREQ);
+	clockevents_config_and_register(&ckevt, MMP_CLOCK_FREQ,
 					MIN_DELTA, MAX_DELTA);
 }
 
diff --git a/arch/arm/mach-moxart/Kconfig b/arch/arm/mach-moxart/Kconfig
index 3795ae2..95a6a4b 100644
--- a/arch/arm/mach-moxart/Kconfig
+++ b/arch/arm/mach-moxart/Kconfig
@@ -2,14 +2,9 @@
 	bool "MOXA ART SoC" if ARCH_MULTI_V4T
 	select CPU_FA526
 	select ARM_DMA_MEM_BUFFERABLE
-	select USE_OF
-	select CLKSRC_OF
 	select CLKSRC_MMIO
-	select HAVE_CLK
-	select COMMON_CLK
 	select GENERIC_IRQ_CHIP
 	select ARCH_REQUIRE_GPIOLIB
-	select GENERIC_CLOCKEVENTS
 	select PHYLIB if NETDEVICES
 	help
 	  Say Y here if you want to run your kernel on hardware with a
diff --git a/arch/arm/mach-msm/Kconfig b/arch/arm/mach-msm/Kconfig
index 9625cf3..a7f959e 100644
--- a/arch/arm/mach-msm/Kconfig
+++ b/arch/arm/mach-msm/Kconfig
@@ -1,50 +1,9 @@
-config ARCH_MSM
-	bool
-
-config ARCH_MSM_DT
-	bool "Qualcomm MSM DT Support" if ARCH_MULTI_V7
-	select ARCH_MSM
-	select ARCH_REQUIRE_GPIOLIB
-	select CLKSRC_OF
-	select GENERIC_CLOCKEVENTS
-	help
-	  Support for Qualcomm's devicetree based MSM systems.
-
 if ARCH_MSM
 
-menu "Qualcomm MSM SoC Selection"
-	depends on ARCH_MSM_DT
-
-config ARCH_MSM8X60
-	bool "Enable support for MSM8X60"
-	select ARM_GIC
-	select CPU_V7
-	select HAVE_SMP
-	select MSM_SCM if SMP
-	select MSM_TIMER
-
-config ARCH_MSM8960
-	bool "Enable support for MSM8960"
-	select ARM_GIC
-	select CPU_V7
-	select HAVE_SMP
-	select MSM_SCM if SMP
-	select MSM_TIMER
-
-config ARCH_MSM8974
-	bool "Enable support for MSM8974"
-	select ARM_GIC
-	select CPU_V7
-	select HAVE_ARM_ARCH_TIMER
-	select HAVE_SMP
-	select MSM_SCM if SMP
-
-endmenu
-
 choice
 	prompt "Qualcomm MSM SoC Type"
 	default ARCH_MSM7X00A
-	depends on ARCH_MSM_NODT
+	depends on ARCH_MSM
 
 config ARCH_MSM7X00A
 	bool "MSM7x00A / MSM7x01A"
@@ -54,7 +13,7 @@
 	select MACH_TROUT if !MACH_HALIBUT
 	select MSM_PROC_COMM
 	select MSM_SMD
-	select MSM_TIMER
+	select CLKSRC_QCOM
 	select MSM_SMD_PKG3
 
 config ARCH_MSM7X30
@@ -66,7 +25,7 @@
 	select MSM_GPIOMUX
 	select MSM_PROC_COMM
 	select MSM_SMD
-	select MSM_TIMER
+	select CLKSRC_QCOM
 	select MSM_VIC
 
 config ARCH_QSD8X50
@@ -78,7 +37,7 @@
 	select MSM_GPIOMUX
 	select MSM_PROC_COMM
 	select MSM_SMD
-	select MSM_TIMER
+	select CLKSRC_QCOM
 	select MSM_VIC
 
 endchoice
@@ -99,7 +58,7 @@
 	bool
 
 menu "Qualcomm MSM Board Type"
-	depends on ARCH_MSM_NODT
+	depends on ARCH_MSM
 
 config MACH_HALIBUT
 	depends on ARCH_MSM
@@ -153,7 +112,4 @@
 config MSM_SCM
 	bool
 
-config MSM_TIMER
-	bool
-
 endif
diff --git a/arch/arm/mach-msm/Makefile b/arch/arm/mach-msm/Makefile
index 8e307a1..27c078a 100644
--- a/arch/arm/mach-msm/Makefile
+++ b/arch/arm/mach-msm/Makefile
@@ -1,4 +1,3 @@
-obj-$(CONFIG_MSM_TIMER) += timer.o
 obj-$(CONFIG_MSM_PROC_COMM) += clock.o
 
 obj-$(CONFIG_MSM_VIC) += irq-vic.o
@@ -14,18 +13,11 @@
 
 obj-$(CONFIG_MSM_SMD) += smd.o smd_debug.o
 obj-$(CONFIG_MSM_SMD) += last_radio_log.o
-obj-$(CONFIG_MSM_SCM) += scm.o scm-boot.o
-
-CFLAGS_scm.o :=$(call as-instr,.arch_extension sec,-DREQUIRES_SEC=1)
-
-obj-$(CONFIG_HOTPLUG_CPU) += hotplug.o
-obj-$(CONFIG_SMP) += headsmp.o platsmp.o
 
 obj-$(CONFIG_MACH_TROUT) += board-trout.o board-trout-gpio.o board-trout-mmc.o devices-msm7x00.o
 obj-$(CONFIG_MACH_TROUT) += board-trout.o board-trout-gpio.o board-trout-mmc.o board-trout-panel.o devices-msm7x00.o
 obj-$(CONFIG_MACH_HALIBUT) += board-halibut.o devices-msm7x00.o
 obj-$(CONFIG_ARCH_MSM7X30) += board-msm7x30.o devices-msm7x30.o
 obj-$(CONFIG_ARCH_QSD8X50) += board-qsd8x50.o devices-qsd8x50.o
-obj-$(CONFIG_ARCH_MSM_DT) += board-dt.o
 obj-$(CONFIG_MSM_GPIOMUX) += gpiomux.o
 obj-$(CONFIG_ARCH_QSD8X50) += gpiomux-8x50.o
diff --git a/arch/arm/mach-msm/common.h b/arch/arm/mach-msm/common.h
index 33c7725..0a4899b 100644
--- a/arch/arm/mach-msm/common.h
+++ b/arch/arm/mach-msm/common.h
@@ -24,7 +24,6 @@
 					  unsigned int mtype, void *caller);
 
 extern struct smp_operations msm_smp_ops;
-extern void msm_cpu_die(unsigned int cpu);
 
 struct msm_mmc_platform_data;
 
diff --git a/arch/arm/mach-msm/headsmp.S b/arch/arm/mach-msm/headsmp.S
deleted file mode 100644
index 6c62c3f..0000000
--- a/arch/arm/mach-msm/headsmp.S
+++ /dev/null
@@ -1,39 +0,0 @@
-/*
- *  linux/arch/arm/mach-realview/headsmp.S
- *
- *  Copyright (c) 2003 ARM Limited
- *  All Rights Reserved
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-#include <linux/linkage.h>
-#include <linux/init.h>
-
-/*
- * MSM specific entry point for secondary CPUs.  This provides
- * a "holding pen" into which all secondary cores are held until we're
- * ready for them to initialise.
- */
-ENTRY(msm_secondary_startup)
-	mrc	p15, 0, r0, c0, c0, 5
-	and	r0, r0, #15
-	adr	r4, 1f
-	ldmia	r4, {r5, r6}
-	sub	r4, r4, r5
-	add	r6, r6, r4
-pen:	ldr	r7, [r6]
-	cmp	r7, r0
-	bne	pen
-
-	/*
-	 * we've been released from the holding pen: secondary_stack
-	 * should now contain the SVC stack for this core
-	 */
-	b	secondary_startup
-ENDPROC(msm_secondary_startup)
-
-	.align
-1:	.long	.
-	.long	pen_release
diff --git a/arch/arm/mach-msm/hotplug.c b/arch/arm/mach-msm/hotplug.c
deleted file mode 100644
index 326a872..0000000
--- a/arch/arm/mach-msm/hotplug.c
+++ /dev/null
@@ -1,74 +0,0 @@
-/*
- *  Copyright (C) 2002 ARM Ltd.
- *  All Rights Reserved
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-#include <linux/kernel.h>
-#include <linux/errno.h>
-#include <linux/smp.h>
-
-#include <asm/smp_plat.h>
-
-#include "common.h"
-
-static inline void cpu_enter_lowpower(void)
-{
-}
-
-static inline void cpu_leave_lowpower(void)
-{
-}
-
-static inline void platform_do_lowpower(unsigned int cpu)
-{
-	/* Just enter wfi for now. TODO: Properly shut off the cpu. */
-	for (;;) {
-		/*
-		 * here's the WFI
-		 */
-		asm("wfi"
-		    :
-		    :
-		    : "memory", "cc");
-
-		if (pen_release == cpu_logical_map(cpu)) {
-			/*
-			 * OK, proper wakeup, we're done
-			 */
-			break;
-		}
-
-		/*
-		 * getting here, means that we have come out of WFI without
-		 * having been woken up - this shouldn't happen
-		 *
-		 * The trouble is, letting people know about this is not really
-		 * possible, since we are currently running incoherently, and
-		 * therefore cannot safely call printk() or anything else
-		 */
-		pr_debug("CPU%u: spurious wakeup call\n", cpu);
-	}
-}
-
-/*
- * platform-specific code to shutdown a CPU
- *
- * Called with IRQs disabled
- */
-void __ref msm_cpu_die(unsigned int cpu)
-{
-	/*
-	 * we're ready for shutdown now, so do it
-	 */
-	cpu_enter_lowpower();
-	platform_do_lowpower(cpu);
-
-	/*
-	 * bring this CPU back into the world of cache
-	 * coherency, and then restore interrupts
-	 */
-	cpu_leave_lowpower();
-}
diff --git a/arch/arm/mach-msm/include/mach/timex.h b/arch/arm/mach-msm/include/mach/timex.h
deleted file mode 100644
index a62e6b2..0000000
--- a/arch/arm/mach-msm/include/mach/timex.h
+++ /dev/null
@@ -1,21 +0,0 @@
-/* arch/arm/mach-msm/include/mach/timex.h
- *
- * Copyright (C) 2007 Google, Inc.
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- */
-
-#ifndef __ASM_ARCH_MSM_TIMEX_H
-#define __ASM_ARCH_MSM_TIMEX_H
-
-#define CLOCK_TICK_RATE		1000000
-
-#endif
diff --git a/arch/arm/mach-mv78xx0/include/mach/timex.h b/arch/arm/mach-mv78xx0/include/mach/timex.h
deleted file mode 100644
index 0e8c443..0000000
--- a/arch/arm/mach-mv78xx0/include/mach/timex.h
+++ /dev/null
@@ -1,9 +0,0 @@
-/*
- * arch/arm/mach-mv78xx0/include/mach/timex.h
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#define CLOCK_TICK_RATE		(100 * HZ)
diff --git a/arch/arm/mach-mvebu/Kconfig b/arch/arm/mach-mvebu/Kconfig
index 5e269d7..875a352 100644
--- a/arch/arm/mach-mvebu/Kconfig
+++ b/arch/arm/mach-mvebu/Kconfig
@@ -2,15 +2,10 @@
 	bool "Marvell SOCs with Device Tree support" if ARCH_MULTI_V7
 	select ARCH_SUPPORTS_BIG_ENDIAN
 	select CLKSRC_MMIO
-	select COMMON_CLK
-	select GENERIC_CLOCKEVENTS
 	select GENERIC_IRQ_CHIP
 	select IRQ_DOMAIN
-	select MULTI_IRQ_HANDLER
 	select PINCTRL
 	select PLAT_ORION
-	select SPARSE_IRQ
-	select CLKDEV_LOOKUP
 	select MVEBU_MBUS
 	select ZONE_DMA if ARM_LPAE
 	select ARCH_REQUIRE_GPIOLIB
@@ -24,7 +19,6 @@
 config MACH_ARMADA_370_XP
 	bool
 	select ARMADA_370_XP_TIMER
-	select HAVE_SMP
 	select CACHE_L2X0
 	select CPU_PJ4B
 
diff --git a/arch/arm/mach-mvebu/Makefile b/arch/arm/mach-mvebu/Makefile
index 878aebe..d998461 100644
--- a/arch/arm/mach-mvebu/Makefile
+++ b/arch/arm/mach-mvebu/Makefile
@@ -3,8 +3,7 @@
 
 AFLAGS_coherency_ll.o		:= -Wa,-march=armv7-a
 
-obj-y				 += system-controller.o mvebu-soc-id.o
+obj-y				 += coherency.o coherency_ll.o pmsu.o system-controller.o mvebu-soc-id.o
 obj-$(CONFIG_MACH_ARMADA_370_XP) += armada-370-xp.o
-obj-$(CONFIG_ARCH_MVEBU)	 += coherency.o coherency_ll.o pmsu.o
 obj-$(CONFIG_SMP)                += platsmp.o headsmp.o
 obj-$(CONFIG_HOTPLUG_CPU)        += hotplug.o
diff --git a/arch/arm/mach-mvebu/armada-370-xp.c b/arch/arm/mach-mvebu/armada-370-xp.c
index f6c9d1d..161cf2f 100644
--- a/arch/arm/mach-mvebu/armada-370-xp.c
+++ b/arch/arm/mach-mvebu/armada-370-xp.c
@@ -31,11 +31,6 @@
 #include "coherency.h"
 #include "mvebu-soc-id.h"
 
-static void __init armada_370_xp_map_io(void)
-{
-	debug_ll_io_init();
-}
-
 static void __init armada_370_xp_timer_and_clk_init(void)
 {
 	of_clk_init(NULL);
@@ -90,7 +85,6 @@
 DT_MACHINE_START(ARMADA_XP_DT, "Marvell Armada 370/XP (Device Tree)")
 	.smp		= smp_ops(armada_xp_smp_ops),
 	.init_machine	= armada_370_xp_dt_init,
-	.map_io		= armada_370_xp_map_io,
 	.init_time	= armada_370_xp_timer_and_clk_init,
 	.restart	= mvebu_restart,
 	.dt_compat	= armada_370_xp_dt_compat,
diff --git a/arch/arm/mach-mvebu/system-controller.c b/arch/arm/mach-mvebu/system-controller.c
index a7fb89a..e6e300a 100644
--- a/arch/arm/mach-mvebu/system-controller.c
+++ b/arch/arm/mach-mvebu/system-controller.c
@@ -54,7 +54,7 @@
 	.system_soft_reset = 0x1,
 };
 
-static struct of_device_id of_system_controller_table[] = {
+static const struct of_device_id of_system_controller_table[] = {
 	{
 		.compatible = "marvell,orion-system-controller",
 		.data = (void *) &orion_system_controller,
@@ -90,13 +90,12 @@
 
 static int __init mvebu_system_controller_init(void)
 {
+	const struct of_device_id *match;
 	struct device_node *np;
 
-	np = of_find_matching_node(NULL, of_system_controller_table);
+	np = of_find_matching_node_and_match(NULL, of_system_controller_table,
+					     &match);
 	if (np) {
-		const struct of_device_id *match =
-		    of_match_node(of_system_controller_table, np);
-		BUG_ON(!match);
 		system_controller_base = of_iomap(np, 0);
 		mvebu_sc = (struct mvebu_system_controller *)match->data;
 		of_node_put(np);
diff --git a/arch/arm/mach-mxs/Kconfig b/arch/arm/mach-mxs/Kconfig
index 8cde9e0..8479413 100644
--- a/arch/arm/mach-mxs/Kconfig
+++ b/arch/arm/mach-mxs/Kconfig
@@ -16,11 +16,7 @@
 	bool "Freescale MXS (i.MX23, i.MX28) support"
 	depends on ARCH_MULTI_V5
 	select ARCH_REQUIRE_GPIOLIB
-	select CLKDEV_LOOKUP
 	select CLKSRC_MMIO
-	select CLKSRC_OF
-	select GENERIC_CLOCKEVENTS
-	select HAVE_CLK_PREPARE
 	select PINCTRL
 	select SOC_BUS
 	select SOC_IMX23
diff --git a/arch/arm/mach-netx/include/mach/timex.h b/arch/arm/mach-netx/include/mach/timex.h
deleted file mode 100644
index 1120dd0..0000000
--- a/arch/arm/mach-netx/include/mach/timex.h
+++ /dev/null
@@ -1,20 +0,0 @@
-/*
- * arch/arm/mach-netx/include/mach/timex.h
- *
- * Copyright (C) 2005 Sascha Hauer <s.hauer@pengutronix.de>, Pengutronix
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2
- * as published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-
-#define CLOCK_TICK_RATE 100000000
diff --git a/arch/arm/mach-netx/time.c b/arch/arm/mach-netx/time.c
index 6df42e6..e234601 100644
--- a/arch/arm/mach-netx/time.c
+++ b/arch/arm/mach-netx/time.c
@@ -28,6 +28,9 @@
 #include <asm/mach/time.h>
 #include <mach/netx-regs.h>
 
+#define NETX_CLOCK_FREQ 100000000
+#define NETX_LATCH DIV_ROUND_CLOSEST(NETX_CLOCK_FREQ, HZ)
+
 #define TIMER_CLOCKEVENT 0
 #define TIMER_CLOCKSOURCE 1
 
@@ -41,7 +44,7 @@
 
 	switch (mode) {
 	case CLOCK_EVT_MODE_PERIODIC:
-		writel(LATCH, NETX_GPIO_COUNTER_MAX(TIMER_CLOCKEVENT));
+		writel(NETX_LATCH, NETX_GPIO_COUNTER_MAX(TIMER_CLOCKEVENT));
 		tmode = NETX_GPIO_COUNTER_CTRL_RST_EN |
 			NETX_GPIO_COUNTER_CTRL_IRQ_EN |
 			NETX_GPIO_COUNTER_CTRL_RUN;
@@ -114,7 +117,7 @@
 	/* Reset the timer value to zero */
 	writel(0, NETX_GPIO_COUNTER_CURRENT(0));
 
-	writel(LATCH, NETX_GPIO_COUNTER_MAX(0));
+	writel(NETX_LATCH, NETX_GPIO_COUNTER_MAX(0));
 
 	/* acknowledge interrupt */
 	writel(COUNTER_BIT(0), NETX_GPIO_IRQ);
@@ -137,11 +140,11 @@
 			NETX_GPIO_COUNTER_CTRL(TIMER_CLOCKSOURCE));
 
 	clocksource_mmio_init(NETX_GPIO_COUNTER_CURRENT(TIMER_CLOCKSOURCE),
-		"netx_timer", CLOCK_TICK_RATE, 200, 32, clocksource_mmio_readl_up);
+		"netx_timer", NETX_CLOCK_FREQ, 200, 32, clocksource_mmio_readl_up);
 
 	/* with max_delta_ns >= delta2ns(0x800) the system currently runs fine.
 	 * Adding some safety ... */
 	netx_clockevent.cpumask = cpumask_of(0);
-	clockevents_config_and_register(&netx_clockevent, CLOCK_TICK_RATE,
+	clockevents_config_and_register(&netx_clockevent, NETX_CLOCK_FREQ,
 					0xa00, 0xfffffffe);
 }
diff --git a/arch/arm/mach-nomadik/Kconfig b/arch/arm/mach-nomadik/Kconfig
index 4d42da4..486d301 100644
--- a/arch/arm/mach-nomadik/Kconfig
+++ b/arch/arm/mach-nomadik/Kconfig
@@ -6,16 +6,11 @@
 	select ARM_VIC
 	select CLKSRC_NOMADIK_MTU
 	select CLKSRC_NOMADIK_MTU_SCHED_CLOCK
-	select CLKSRC_OF
-	select COMMON_CLK
 	select CPU_ARM926T
-	select GENERIC_CLOCKEVENTS
 	select MIGHT_HAVE_CACHE_L2X0
 	select PINCTRL
 	select PINCTRL_NOMADIK
 	select PINCTRL_STN8815
-	select SPARSE_IRQ
-	select USE_OF
 	help
 	  Support for the Nomadik platform by ST-Ericsson
 
diff --git a/arch/arm/mach-nspire/Kconfig b/arch/arm/mach-nspire/Kconfig
index 59d8f0a..bc41f26 100644
--- a/arch/arm/mach-nspire/Kconfig
+++ b/arch/arm/mach-nspire/Kconfig
@@ -3,14 +3,9 @@
 	depends on ARCH_MULTI_V4_V5
 	depends on MMU
 	select CPU_ARM926T
-	select COMMON_CLK
-	select GENERIC_CLOCKEVENTS
 	select GENERIC_IRQ_CHIP
-	select SPARSE_IRQ
 	select ARM_AMBA
 	select ARM_VIC
 	select ARM_TIMER_SP804
-	select USE_OF
-	select CLKSRC_OF
 	help
 	  This enables support for systems using the TI-NSPIRE CPU
diff --git a/arch/arm/mach-omap1/include/mach/timex.h b/arch/arm/mach-omap1/include/mach/timex.h
deleted file mode 100644
index 4793790..0000000
--- a/arch/arm/mach-omap1/include/mach/timex.h
+++ /dev/null
@@ -1,5 +0,0 @@
-/*
- * arch/arm/mach-omap1/include/mach/timex.h
- */
-
-#include <plat/timex.h>
diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig
index e2ce4f8..922cbd8 100644
--- a/arch/arm/mach-omap2/Kconfig
+++ b/arch/arm/mach-omap2/Kconfig
@@ -6,7 +6,6 @@
 	depends on ARCH_MULTI_V6
 	select ARCH_OMAP2PLUS
 	select CPU_V6
-	select MULTI_IRQ_HANDLER
 	select SOC_HAS_OMAP2_SDRC
 
 config ARCH_OMAP3
@@ -15,8 +14,6 @@
 	select ARCH_OMAP2PLUS
 	select ARCH_HAS_OPP
 	select ARM_CPU_SUSPEND if PM
-	select CPU_V7
-	select MULTI_IRQ_HANDLER
 	select OMAP_INTERCONNECT
 	select PM_OPP if PM
 	select PM_RUNTIME if CPU_IDLE
@@ -33,10 +30,8 @@
 	select ARM_ERRATA_720789
 	select ARM_GIC
 	select CACHE_L2X0
-	select CPU_V7
 	select HAVE_ARM_SCU if SMP
 	select HAVE_ARM_TWD if SMP
-	select HAVE_SMP
 	select OMAP_INTERCONNECT
 	select PL310_ERRATA_588369
 	select PL310_ERRATA_727915
@@ -52,10 +47,8 @@
 	select ARCH_OMAP2PLUS
 	select ARM_CPU_SUSPEND if PM
 	select ARM_GIC
-	select CPU_V7
 	select HAVE_ARM_SCU if SMP
 	select HAVE_ARM_TWD if SMP
-	select HAVE_SMP
 	select HAVE_ARM_ARCH_TIMER
 	select ARM_ERRATA_798181 if SMP
 
@@ -64,15 +57,11 @@
 	depends on ARCH_MULTI_V7
 	select ARCH_OMAP2PLUS
 	select ARM_CPU_SUSPEND if PM
-	select CPU_V7
-	select MULTI_IRQ_HANDLER
 
 config SOC_AM43XX
 	bool "TI AM43x"
 	depends on ARCH_MULTI_V7
-	select CPU_V7
 	select ARCH_OMAP2PLUS
-	select MULTI_IRQ_HANDLER
 	select ARM_GIC
 	select MACH_OMAP_GENERIC
 
@@ -82,8 +71,6 @@
 	select ARCH_OMAP2PLUS
 	select ARM_CPU_SUSPEND if PM
 	select ARM_GIC
-	select CPU_V7
-	select HAVE_SMP
 	select HAVE_ARM_ARCH_TIMER
 
 config ARCH_OMAP2PLUS
@@ -94,17 +81,13 @@
 	select ARCH_OMAP
 	select ARCH_REQUIRE_GPIOLIB
 	select CLKSRC_MMIO
-	select COMMON_CLK
-	select GENERIC_CLOCKEVENTS
 	select GENERIC_IRQ_CHIP
 	select MACH_OMAP_GENERIC
 	select OMAP_DM_TIMER
 	select PINCTRL
 	select PROC_DEVICETREE if PROC_FS
 	select SOC_BUS
-	select SPARSE_IRQ
 	select TI_PRIV_EDMA
-	select USE_OF
 	help
 	  Systems based on OMAP2, OMAP3, OMAP4 or OMAP5
 
diff --git a/arch/arm/mach-omap2/include/mach/timex.h b/arch/arm/mach-omap2/include/mach/timex.h
deleted file mode 100644
index de9f8fc..0000000
--- a/arch/arm/mach-omap2/include/mach/timex.h
+++ /dev/null
@@ -1,5 +0,0 @@
-/*
- * arch/arm/mach-omap2/include/mach/timex.h
- */
-
-#include <plat/timex.h>
diff --git a/arch/arm/mach-orion5x/include/mach/timex.h b/arch/arm/mach-orion5x/include/mach/timex.h
deleted file mode 100644
index 4c69820..0000000
--- a/arch/arm/mach-orion5x/include/mach/timex.h
+++ /dev/null
@@ -1,11 +0,0 @@
-/*
- * arch/arm/mach-orion5x/include/mach/timex.h
- *
- * Tzachi Perelstein <tzachi@marvell.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#define CLOCK_TICK_RATE		(100 * HZ)
diff --git a/arch/arm/mach-picoxcell/Kconfig b/arch/arm/mach-picoxcell/Kconfig
index b1022f4..eca9eb1 100644
--- a/arch/arm/mach-picoxcell/Kconfig
+++ b/arch/arm/mach-picoxcell/Kconfig
@@ -1,12 +1,7 @@
 config ARCH_PICOXCELL
 	bool "Picochip PicoXcell" if ARCH_MULTI_V6
 	select ARCH_REQUIRE_GPIOLIB
-	select ARM_PATCH_PHYS_VIRT
 	select ARM_VIC
-	select CPU_V6K
 	select DW_APB_TIMER_OF
-	select GENERIC_CLOCKEVENTS
 	select HAVE_TCM
 	select NO_IOPORT
-	select SPARSE_IRQ
-	select USE_OF
diff --git a/arch/arm/mach-prima2/Kconfig b/arch/arm/mach-prima2/Kconfig
index 6988b11..3e81891 100644
--- a/arch/arm/mach-prima2/Kconfig
+++ b/arch/arm/mach-prima2/Kconfig
@@ -1,9 +1,8 @@
 config ARCH_SIRF
 	bool "CSR SiRF" if ARCH_MULTI_V7
+	select ARCH_HAS_RESET_CONTROLLER
 	select ARCH_REQUIRE_GPIOLIB
-	select GENERIC_CLOCKEVENTS
 	select GENERIC_IRQ_CHIP
-	select MIGHT_HAVE_CACHE_L2X0
 	select NO_IOPORT
 	select PINCTRL
 	select PINCTRL_SIRF
@@ -17,7 +16,6 @@
 config ARCH_ATLAS6
 	bool "CSR SiRFSoC ATLAS6 ARM Cortex A9 Platform"
 	default y
-	select CPU_V7
 	select SIRF_IRQ
 	help
           Support for CSR SiRFSoC ARM Cortex A9 Platform
@@ -25,7 +23,6 @@
 config ARCH_PRIMA2
 	bool "CSR SiRFSoC PRIMA2 ARM Cortex A9 Platform"
 	default y
-	select CPU_V7
 	select SIRF_IRQ
 	select ZONE_DMA
 	help
@@ -35,9 +32,7 @@
 	bool "CSR SiRFSoC MARCO ARM Cortex A9 Platform"
 	default y
 	select ARM_GIC
-	select CPU_V7
 	select HAVE_ARM_SCU if SMP
-	select HAVE_SMP
 	select SMP_ON_UP if SMP
 	help
           Support for CSR SiRFSoC ARM Cortex A9 Platform
diff --git a/arch/arm/mach-prima2/common.c b/arch/arm/mach-prima2/common.c
index d49aff7..3b8865a 100644
--- a/arch/arm/mach-prima2/common.c
+++ b/arch/arm/mach-prima2/common.c
@@ -15,7 +15,7 @@
 #include <linux/of_platform.h>
 #include "common.h"
 
-void __init sirfsoc_init_late(void)
+static void __init sirfsoc_init_late(void)
 {
 	sirfsoc_pm_init();
 }
@@ -27,7 +27,7 @@
 }
 
 #ifdef CONFIG_ARCH_ATLAS6
-static const char *atlas6_dt_match[] __initdata = {
+static const char *atlas6_dt_match[] __initconst = {
 	"sirf,atlas6",
 	NULL
 };
@@ -42,7 +42,7 @@
 #endif
 
 #ifdef CONFIG_ARCH_PRIMA2
-static const char *prima2_dt_match[] __initdata = {
+static const char *prima2_dt_match[] __initconst = {
 	"sirf,prima2",
 	NULL
 };
@@ -58,7 +58,7 @@
 #endif
 
 #ifdef CONFIG_ARCH_MARCO
-static const char *marco_dt_match[] __initdata = {
+static const char *marco_dt_match[] __initconst = {
 	"sirf,marco",
 	NULL
 };
diff --git a/arch/arm/mach-prima2/l2x0.c b/arch/arm/mach-prima2/l2x0.c
index cbcbe9c..c710253 100644
--- a/arch/arm/mach-prima2/l2x0.c
+++ b/arch/arm/mach-prima2/l2x0.c
@@ -11,24 +11,23 @@
 #include <linux/of.h>
 #include <asm/hardware/cache-l2x0.h>
 
-struct l2x0_aux
-{
+struct l2x0_aux {
 	u32 val;
 	u32 mask;
 };
 
-static struct l2x0_aux prima2_l2x0_aux __initconst = {
+static const struct l2x0_aux prima2_l2x0_aux __initconst = {
 	.val = 2 << L2X0_AUX_CTRL_WAY_SIZE_SHIFT,
 	.mask =	0,
 };
 
-static struct l2x0_aux marco_l2x0_aux __initconst = {
+static const struct l2x0_aux marco_l2x0_aux __initconst = {
 	.val = (2 << L2X0_AUX_CTRL_WAY_SIZE_SHIFT) |
 		(1 << L2X0_AUX_CTRL_ASSOCIATIVITY_SHIFT),
 	.mask = L2X0_AUX_CTRL_MASK,
 };
 
-static struct of_device_id sirf_l2x0_ids[] __initconst = {
+static const struct of_device_id sirf_l2x0_ids[] __initconst = {
 	{ .compatible = "sirf,prima2-pl310-cache", .data = &prima2_l2x0_aux, },
 	{ .compatible = "sirf,marco-pl310-cache", .data = &marco_l2x0_aux, },
 	{},
diff --git a/arch/arm/mach-prima2/platsmp.c b/arch/arm/mach-prima2/platsmp.c
index e358b07..335c12e 100644
--- a/arch/arm/mach-prima2/platsmp.c
+++ b/arch/arm/mach-prima2/platsmp.c
@@ -138,9 +138,9 @@
 }
 
 struct smp_operations sirfsoc_smp_ops __initdata = {
-        .smp_prepare_cpus       = sirfsoc_smp_prepare_cpus,
-        .smp_secondary_init     = sirfsoc_secondary_init,
-        .smp_boot_secondary     = sirfsoc_boot_secondary,
+	.smp_prepare_cpus       = sirfsoc_smp_prepare_cpus,
+	.smp_secondary_init     = sirfsoc_secondary_init,
+	.smp_boot_secondary     = sirfsoc_boot_secondary,
 #ifdef CONFIG_HOTPLUG_CPU
 	.cpu_die                = sirfsoc_cpu_die,
 #endif
diff --git a/arch/arm/mach-prima2/rstc.c b/arch/arm/mach-prima2/rstc.c
index ccb5339..a599767 100644
--- a/arch/arm/mach-prima2/rstc.c
+++ b/arch/arm/mach-prima2/rstc.c
@@ -13,57 +13,36 @@
 #include <linux/device.h>
 #include <linux/of.h>
 #include <linux/of_address.h>
+#include <linux/platform_device.h>
 #include <linux/reboot.h>
+#include <linux/reset-controller.h>
+
+#define SIRFSOC_RSTBIT_NUM	64
 
 void __iomem *sirfsoc_rstc_base;
 static DEFINE_MUTEX(rstc_lock);
 
-static struct of_device_id rstc_ids[]  = {
-	{ .compatible = "sirf,prima2-rstc" },
-	{ .compatible = "sirf,marco-rstc" },
-	{},
-};
-
-static int __init sirfsoc_of_rstc_init(void)
+static int sirfsoc_reset_module(struct reset_controller_dev *rcdev,
+					unsigned long sw_reset_idx)
 {
-	struct device_node *np;
+	u32 reset_bit = sw_reset_idx;
 
-	np = of_find_matching_node(NULL, rstc_ids);
-	if (!np) {
-		pr_err("unable to find compatible sirf rstc node in dtb\n");
-		return -ENOENT;
-	}
-
-	sirfsoc_rstc_base = of_iomap(np, 0);
-	if (!sirfsoc_rstc_base)
-		panic("unable to map rstc cpu registers\n");
-
-	of_node_put(np);
-
-	return 0;
-}
-early_initcall(sirfsoc_of_rstc_init);
-
-int sirfsoc_reset_device(struct device *dev)
-{
-	u32 reset_bit;
-
-	if (of_property_read_u32(dev->of_node, "reset-bit", &reset_bit))
+	if (reset_bit >= SIRFSOC_RSTBIT_NUM)
 		return -EINVAL;
 
 	mutex_lock(&rstc_lock);
 
-	if (of_device_is_compatible(dev->of_node, "sirf,prima2-rstc")) {
+	if (of_device_is_compatible(rcdev->of_node, "sirf,prima2-rstc")) {
 		/*
 		 * Writing 1 to this bit resets corresponding block. Writing 0 to this
 		 * bit de-asserts reset signal of the corresponding block.
 		 * datasheet doesn't require explicit delay between the set and clear
 		 * of reset bit. it could be shorter if tests pass.
 		 */
-		writel(readl(sirfsoc_rstc_base + (reset_bit / 32) * 4) | reset_bit,
+		writel(readl(sirfsoc_rstc_base + (reset_bit / 32) * 4) | (1 << reset_bit),
 			sirfsoc_rstc_base + (reset_bit / 32) * 4);
 		msleep(10);
-		writel(readl(sirfsoc_rstc_base + (reset_bit / 32) * 4) & ~reset_bit,
+		writel(readl(sirfsoc_rstc_base + (reset_bit / 32) * 4) & ~(1 << reset_bit),
 			sirfsoc_rstc_base + (reset_bit / 32) * 4);
 	} else {
 		/*
@@ -73,9 +52,9 @@
 		 * datasheet doesn't require explicit delay between the set and clear
 		 * of reset bit. it could be shorter if tests pass.
 		 */
-		writel(reset_bit, sirfsoc_rstc_base + (reset_bit / 32) * 8);
+		writel(1 << reset_bit, sirfsoc_rstc_base + (reset_bit / 32) * 8);
 		msleep(10);
-		writel(reset_bit, sirfsoc_rstc_base + (reset_bit / 32) * 8 + 4);
+		writel(1 << reset_bit, sirfsoc_rstc_base + (reset_bit / 32) * 8 + 4);
 	}
 
 	mutex_unlock(&rstc_lock);
@@ -83,6 +62,52 @@
 	return 0;
 }
 
+static struct reset_control_ops sirfsoc_rstc_ops = {
+	.reset = sirfsoc_reset_module,
+};
+
+static struct reset_controller_dev sirfsoc_reset_controller = {
+	.ops = &sirfsoc_rstc_ops,
+	.nr_resets = SIRFSOC_RSTBIT_NUM,
+};
+
+static int sirfsoc_rstc_probe(struct platform_device *pdev)
+{
+	struct device_node *np = pdev->dev.of_node;
+	sirfsoc_rstc_base = of_iomap(np, 0);
+	if (!sirfsoc_rstc_base) {
+		dev_err(&pdev->dev, "unable to map rstc cpu registers\n");
+		return -ENOMEM;
+	}
+
+	sirfsoc_reset_controller.of_node = np;
+
+	reset_controller_register(&sirfsoc_reset_controller);
+
+	return 0;
+}
+
+static const struct of_device_id rstc_ids[]  = {
+	{ .compatible = "sirf,prima2-rstc" },
+	{ .compatible = "sirf,marco-rstc" },
+	{},
+};
+
+static struct platform_driver sirfsoc_rstc_driver = {
+	.probe		= sirfsoc_rstc_probe,
+	.driver		= {
+		.name	= "sirfsoc_rstc",
+		.owner	= THIS_MODULE,
+		.of_match_table = rstc_ids,
+	},
+};
+
+static int __init sirfsoc_rstc_init(void)
+{
+	return platform_driver_register(&sirfsoc_rstc_driver);
+}
+subsys_initcall(sirfsoc_rstc_init);
+
 #define SIRFSOC_SYS_RST_BIT  BIT(31)
 
 void sirfsoc_restart(enum reboot_mode mode, const char *cmd)
diff --git a/arch/arm/mach-prima2/rtciobrg.c b/arch/arm/mach-prima2/rtciobrg.c
index 9f2da2e..a17c88b 100644
--- a/arch/arm/mach-prima2/rtciobrg.c
+++ b/arch/arm/mach-prima2/rtciobrg.c
@@ -137,4 +137,4 @@
 MODULE_AUTHOR("Zhiwu Song <zhiwu.song@csr.com>, "
 		"Barry Song <baohua.song@csr.com>");
 MODULE_DESCRIPTION("CSR SiRFprimaII rtc io bridge");
-MODULE_LICENSE("GPL");
+MODULE_LICENSE("GPL v2");
diff --git a/arch/arm/mach-pxa/include/mach/timex.h b/arch/arm/mach-pxa/include/mach/timex.h
deleted file mode 100644
index af6760a..0000000
--- a/arch/arm/mach-pxa/include/mach/timex.h
+++ /dev/null
@@ -1,34 +0,0 @@
-/*
- * arch/arm/mach-pxa/include/mach/timex.h
- *
- * Author:	Nicolas Pitre
- * Created:	Jun 15, 2001
- * Copyright:	MontaVista Software Inc.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-/* Various drivers are still using the constant of CLOCK_TICK_RATE, for
- * those drivers to at least work, the definition is provided here.
- *
- * NOTE: this is no longer accurate when multiple processors and boards
- * are selected, newer drivers should not depend on this any more.  Use
- * either the clocksource/clockevent or get this at run-time by calling
- * get_clock_tick_rate() (as defined in generic.c).
- */
-
-#if defined(CONFIG_PXA25x)
-/* PXA250/210 timer base */
-#define CLOCK_TICK_RATE 3686400
-#elif defined(CONFIG_PXA27x)
-/* PXA27x timer base */
-#ifdef CONFIG_MACH_MAINSTONE
-#define CLOCK_TICK_RATE 3249600
-#else
-#define CLOCK_TICK_RATE 3250000
-#endif
-#else
-#define CLOCK_TICK_RATE 3250000
-#endif
diff --git a/arch/arm/mach-qcom/Kconfig b/arch/arm/mach-qcom/Kconfig
new file mode 100644
index 0000000..a028be2
--- /dev/null
+++ b/arch/arm/mach-qcom/Kconfig
@@ -0,0 +1,33 @@
+config ARCH_QCOM
+	bool "Qualcomm Support" if ARCH_MULTI_V7
+	select ARCH_REQUIRE_GPIOLIB
+	select ARM_GIC
+	select CLKSRC_OF
+	select GENERIC_CLOCKEVENTS
+	select HAVE_SMP
+	select QCOM_SCM if SMP
+	help
+	  Support for Qualcomm's devicetree based systems.
+
+if ARCH_QCOM
+
+menu "Qualcomm SoC Selection"
+
+config ARCH_MSM8X60
+	bool "Enable support for MSM8X60"
+	select CLKSRC_QCOM
+
+config ARCH_MSM8960
+	bool "Enable support for MSM8960"
+	select CLKSRC_QCOM
+
+config ARCH_MSM8974
+	bool "Enable support for MSM8974"
+	select HAVE_ARM_ARCH_TIMER
+
+endmenu
+
+config QCOM_SCM
+	bool
+
+endif
diff --git a/arch/arm/mach-qcom/Makefile b/arch/arm/mach-qcom/Makefile
new file mode 100644
index 0000000..8f756ae
--- /dev/null
+++ b/arch/arm/mach-qcom/Makefile
@@ -0,0 +1,5 @@
+obj-y			:= board.o
+obj-$(CONFIG_SMP)	+= platsmp.o
+obj-$(CONFIG_QCOM_SCM)	+= scm.o scm-boot.o
+
+CFLAGS_scm.o :=$(call as-instr,.arch_extension sec,-DREQUIRES_SEC=1)
diff --git a/arch/arm/mach-msm/board-dt.c b/arch/arm/mach-qcom/board.c
similarity index 68%
rename from arch/arm/mach-msm/board-dt.c
rename to arch/arm/mach-qcom/board.c
index 1f11d93..830f69c 100644
--- a/arch/arm/mach-msm/board-dt.c
+++ b/arch/arm/mach-qcom/board.c
@@ -1,4 +1,4 @@
-/* Copyright (c) 2010-2012,2013 The Linux Foundation. All rights reserved.
+/* Copyright (c) 2010-2014 The Linux Foundation. All rights reserved.
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License version 2 and
@@ -17,10 +17,9 @@
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 
-#include "common.h"
+extern struct smp_operations qcom_smp_ops;
 
-static const char * const msm_dt_match[] __initconst = {
-	"qcom,msm8660-fluid",
+static const char * const qcom_dt_match[] __initconst = {
 	"qcom,msm8660-surf",
 	"qcom,msm8960-cdp",
 	NULL
@@ -31,11 +30,11 @@
 	NULL
 };
 
-DT_MACHINE_START(MSM_DT, "Qualcomm MSM (Flattened Device Tree)")
-	.smp = smp_ops(msm_smp_ops),
-	.dt_compat = msm_dt_match,
+DT_MACHINE_START(QCOM_DT, "Qualcomm (Flattened Device Tree)")
+	.smp = smp_ops(qcom_smp_ops),
+	.dt_compat = qcom_dt_match,
 MACHINE_END
 
-DT_MACHINE_START(APQ_DT, "Qualcomm MSM (Flattened Device Tree)")
+DT_MACHINE_START(APQ_DT, "Qualcomm (Flattened Device Tree)")
 	.dt_compat = apq8074_dt_match,
 MACHINE_END
diff --git a/arch/arm/mach-msm/platsmp.c b/arch/arm/mach-qcom/platsmp.c
similarity index 65%
rename from arch/arm/mach-msm/platsmp.c
rename to arch/arm/mach-qcom/platsmp.c
index f10a1f5..9c53ea7 100644
--- a/arch/arm/mach-msm/platsmp.c
+++ b/arch/arm/mach-qcom/platsmp.c
@@ -2,6 +2,7 @@
  *  Copyright (C) 2002 ARM Ltd.
  *  All Rights Reserved
  *  Copyright (c) 2010, Code Aurora Forum. All rights reserved.
+ *  Copyright (c) 2014 The Linux Foundation. All rights reserved.
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License version 2 as
@@ -12,42 +13,38 @@
 #include <linux/errno.h>
 #include <linux/delay.h>
 #include <linux/device.h>
-#include <linux/jiffies.h>
 #include <linux/smp.h>
 #include <linux/io.h>
 
-#include <asm/cacheflush.h>
 #include <asm/cputype.h>
-#include <asm/mach-types.h>
 #include <asm/smp_plat.h>
 
 #include "scm-boot.h"
-#include "common.h"
 
 #define VDD_SC1_ARRAY_CLAMP_GFS_CTL 0x15A0
 #define SCSS_CPU1CORE_RESET 0xD80
 #define SCSS_DBG_STATUS_CORE_PWRDUP 0xE64
 
-extern void msm_secondary_startup(void);
+extern void secondary_startup(void);
 
 static DEFINE_SPINLOCK(boot_lock);
 
+#ifdef CONFIG_HOTPLUG_CPU
+static void __ref qcom_cpu_die(unsigned int cpu)
+{
+	wfi();
+}
+#endif
+
 static inline int get_core_count(void)
 {
 	/* 1 + the PART[1:0] field of MIDR */
 	return ((read_cpuid_id() >> 4) & 3) + 1;
 }
 
-static void msm_secondary_init(unsigned int cpu)
+static void qcom_secondary_init(unsigned int cpu)
 {
 	/*
-	 * let the primary processor know we're out of the
-	 * pen, then head off into the C entry point
-	 */
-	pen_release = -1;
-	smp_wmb();
-
-	/*
 	 * Synchronise with the boot thread.
 	 */
 	spin_lock(&boot_lock);
@@ -57,7 +54,7 @@
 static void prepare_cold_cpu(unsigned int cpu)
 {
 	int ret;
-	ret = scm_set_boot_addr(virt_to_phys(msm_secondary_startup),
+	ret = scm_set_boot_addr(virt_to_phys(secondary_startup),
 				SCM_FLAG_COLDBOOT_CPU1);
 	if (ret == 0) {
 		void __iomem *sc1_base_ptr;
@@ -73,9 +70,8 @@
 				  "address\n");
 }
 
-static int msm_boot_secondary(unsigned int cpu, struct task_struct *idle)
+static int qcom_boot_secondary(unsigned int cpu, struct task_struct *idle)
 {
-	unsigned long timeout;
 	static int cold_boot_done;
 
 	/* Only need to bring cpu out of reset this way once */
@@ -91,39 +87,19 @@
 	spin_lock(&boot_lock);
 
 	/*
-	 * The secondary processor is waiting to be released from
-	 * the holding pen - release it, then wait for it to flag
-	 * that it has been released by resetting pen_release.
-	 *
-	 * Note that "pen_release" is the hardware CPU ID, whereas
-	 * "cpu" is Linux's internal ID.
-	 */
-	pen_release = cpu_logical_map(cpu);
-	sync_cache_w(&pen_release);
-
-	/*
 	 * Send the secondary CPU a soft interrupt, thereby causing
 	 * the boot monitor to read the system wide flags register,
 	 * and branch to the address found there.
 	 */
 	arch_send_wakeup_ipi_mask(cpumask_of(cpu));
 
-	timeout = jiffies + (1 * HZ);
-	while (time_before(jiffies, timeout)) {
-		smp_rmb();
-		if (pen_release == -1)
-			break;
-
-		udelay(10);
-	}
-
 	/*
 	 * now the secondary core is starting up let it run its
 	 * calibrations, then wait for it to finish
 	 */
 	spin_unlock(&boot_lock);
 
-	return pen_release != -1 ? -ENOSYS : 0;
+	return 0;
 }
 
 /*
@@ -132,7 +108,7 @@
  * does not support the ARM SCU, so just set the possible cpu mask to
  * NR_CPUS.
  */
-static void __init msm_smp_init_cpus(void)
+static void __init qcom_smp_init_cpus(void)
 {
 	unsigned int i, ncores = get_core_count();
 
@@ -146,16 +122,16 @@
 		set_cpu_possible(i, true);
 }
 
-static void __init msm_smp_prepare_cpus(unsigned int max_cpus)
+static void __init qcom_smp_prepare_cpus(unsigned int max_cpus)
 {
 }
 
-struct smp_operations msm_smp_ops __initdata = {
-	.smp_init_cpus		= msm_smp_init_cpus,
-	.smp_prepare_cpus	= msm_smp_prepare_cpus,
-	.smp_secondary_init	= msm_secondary_init,
-	.smp_boot_secondary	= msm_boot_secondary,
+struct smp_operations qcom_smp_ops __initdata = {
+	.smp_init_cpus		= qcom_smp_init_cpus,
+	.smp_prepare_cpus	= qcom_smp_prepare_cpus,
+	.smp_secondary_init	= qcom_secondary_init,
+	.smp_boot_secondary	= qcom_boot_secondary,
 #ifdef CONFIG_HOTPLUG_CPU
-	.cpu_die		= msm_cpu_die,
+	.cpu_die		= qcom_cpu_die,
 #endif
 };
diff --git a/arch/arm/mach-msm/scm-boot.c b/arch/arm/mach-qcom/scm-boot.c
similarity index 100%
rename from arch/arm/mach-msm/scm-boot.c
rename to arch/arm/mach-qcom/scm-boot.c
diff --git a/arch/arm/mach-msm/scm-boot.h b/arch/arm/mach-qcom/scm-boot.h
similarity index 100%
rename from arch/arm/mach-msm/scm-boot.h
rename to arch/arm/mach-qcom/scm-boot.h
diff --git a/arch/arm/mach-msm/scm.c b/arch/arm/mach-qcom/scm.c
similarity index 100%
rename from arch/arm/mach-msm/scm.c
rename to arch/arm/mach-qcom/scm.c
diff --git a/arch/arm/mach-msm/scm.h b/arch/arm/mach-qcom/scm.h
similarity index 100%
rename from arch/arm/mach-msm/scm.h
rename to arch/arm/mach-qcom/scm.h
diff --git a/arch/arm/mach-realview/include/mach/timex.h b/arch/arm/mach-realview/include/mach/timex.h
deleted file mode 100644
index 4eeb069..0000000
--- a/arch/arm/mach-realview/include/mach/timex.h
+++ /dev/null
@@ -1,23 +0,0 @@
-/*
- *  arch/arm/mach-realview/include/mach/timex.h
- *
- *  RealView architecture timex specifications
- *
- *  Copyright (C) 2003 ARM Limited
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-
-#define CLOCK_TICK_RATE		(50000000 / 16)
diff --git a/arch/arm/mach-rockchip/Kconfig b/arch/arm/mach-rockchip/Kconfig
index cf073de..6b2f586 100644
--- a/arch/arm/mach-rockchip/Kconfig
+++ b/arch/arm/mach-rockchip/Kconfig
@@ -6,9 +6,6 @@
 	select ARM_GIC
 	select CACHE_L2X0
 	select HAVE_ARM_TWD if SMP
-	select HAVE_SMP
-	select COMMON_CLK
-	select GENERIC_CLOCKEVENTS
 	select DW_APB_TIMER_OF
 	select ARM_GLOBAL_TIMER
 	select CLKSRC_ARM_GLOBAL_TIMER_SCHED_CLOCK
diff --git a/arch/arm/mach-rpc/include/mach/timex.h b/arch/arm/mach-rpc/include/mach/timex.h
deleted file mode 100644
index dd75e73..0000000
--- a/arch/arm/mach-rpc/include/mach/timex.h
+++ /dev/null
@@ -1,17 +0,0 @@
-/*
- *  arch/arm/mach-rpc/include/mach/timex.h
- *
- *  Copyright (C) 1997, 1998 Russell King
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- *  RiscPC architecture timex specifications
- */
-
-/*
- * On the RiscPC, the clock ticks at 2MHz.
- */
-#define CLOCK_TICK_RATE		2000000
-
diff --git a/arch/arm/mach-rpc/time.c b/arch/arm/mach-rpc/time.c
index 9a6def1..99363ae 100644
--- a/arch/arm/mach-rpc/time.c
+++ b/arch/arm/mach-rpc/time.c
@@ -24,6 +24,9 @@
 
 #include <asm/mach/time.h>
 
+#define RPC_CLOCK_FREQ 2000000
+#define RPC_LATCH DIV_ROUND_CLOSEST(RPC_CLOCK_FREQ, HZ)
+
 static u32 ioc_timer_gettimeoffset(void)
 {
 	unsigned int count1, count2, status;
@@ -46,23 +49,23 @@
 		 * and count2.
 		 */
 		if (status & (1 << 5))
-			offset -= LATCH;
+			offset -= RPC_LATCH;
 	} else if (count2 > count1) {
 		/*
 		 * We have just had another interrupt between reading
 		 * count1 and count2.
 		 */
-		offset -= LATCH;
+		offset -= RPC_LATCH;
 	}
 
-	offset = (LATCH - offset) * (tick_nsec / 1000);
-	return ((offset + LATCH/2) / LATCH) * 1000;
+	offset = (RPC_LATCH - offset) * (tick_nsec / 1000);
+	return DIV_ROUND_CLOSEST(offset, RPC_LATCH) * 1000;
 }
 
 void __init ioctime_init(void)
 {
-	ioc_writeb(LATCH & 255, IOC_T0LTCHL);
-	ioc_writeb(LATCH >> 8, IOC_T0LTCHH);
+	ioc_writeb(RPC_LATCH & 255, IOC_T0LTCHL);
+	ioc_writeb(RPC_LATCH >> 8, IOC_T0LTCHH);
 	ioc_writeb(0, IOC_T0GO);
 }
 
diff --git a/arch/arm/mach-s3c24xx/Kconfig b/arch/arm/mach-s3c24xx/Kconfig
index d876431..bb1fa603 100644
--- a/arch/arm/mach-s3c24xx/Kconfig
+++ b/arch/arm/mach-s3c24xx/Kconfig
@@ -521,7 +521,6 @@
 	select HAVE_PATA_PLATFORM
 	select S3C2440_XTAL_12000000
 	select S3C24XX_DCLK
-	select S3C24XX_GPIO_EXTRA64
 	select S3C24XX_SIMTEC_PM if PM
 	select S3C_DEV_USB_HOST
 	help
@@ -562,7 +561,6 @@
 	select S3C2410_IOTIMING if ARM_S3C2440_CPUFREQ
 	select S3C2440_XTAL_12000000
 	select S3C24XX_DCLK
-	select S3C24XX_GPIO_EXTRA128
 	select S3C24XX_SIMTEC_PM if PM
 	select S3C_DEV_NAND
 	select S3C_DEV_USB_HOST
diff --git a/arch/arm/mach-s3c24xx/clock-s3c2410.c b/arch/arm/mach-s3c24xx/clock-s3c2410.c
index d39d3c7..d1afcf9 100644
--- a/arch/arm/mach-s3c24xx/clock-s3c2410.c
+++ b/arch/arm/mach-s3c24xx/clock-s3c2410.c
@@ -30,13 +30,12 @@
 #include <linux/mutex.h>
 #include <linux/delay.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 #include <linux/io.h>
 
 #include <asm/mach/map.h>
 
 #include <mach/hardware.h>
-
-#include <plat/regs-serial.h>
 #include <mach/regs-clock.h>
 #include <mach/regs-gpio.h>
 
diff --git a/arch/arm/mach-s3c24xx/clock-s3c2412.c b/arch/arm/mach-s3c24xx/clock-s3c2412.c
index 11b3b28..192a5b2 100644
--- a/arch/arm/mach-s3c24xx/clock-s3c2412.c
+++ b/arch/arm/mach-s3c24xx/clock-s3c2412.c
@@ -31,13 +31,12 @@
 #include <linux/mutex.h>
 #include <linux/delay.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 #include <linux/io.h>
 
 #include <asm/mach/map.h>
 
 #include <mach/hardware.h>
-
-#include <plat/regs-serial.h>
 #include <mach/regs-clock.h>
 #include <mach/regs-gpio.h>
 
diff --git a/arch/arm/mach-s3c24xx/clock-s3c2440.c b/arch/arm/mach-s3c24xx/clock-s3c2440.c
index aaf006d..5527226 100644
--- a/arch/arm/mach-s3c24xx/clock-s3c2440.c
+++ b/arch/arm/mach-s3c24xx/clock-s3c2440.c
@@ -34,6 +34,7 @@
 #include <linux/clk.h>
 #include <linux/io.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 
 #include <mach/hardware.h>
 #include <linux/atomic.h>
@@ -43,7 +44,6 @@
 
 #include <plat/clock.h>
 #include <plat/cpu.h>
-#include <plat/regs-serial.h>
 
 /* S3C2440 extended clock support */
 
diff --git a/arch/arm/mach-s3c24xx/common.c b/arch/arm/mach-s3c24xx/common.c
index 4adaa4b..64b6eda 100644
--- a/arch/arm/mach-s3c24xx/common.c
+++ b/arch/arm/mach-s3c24xx/common.c
@@ -27,6 +27,7 @@
 #include <linux/interrupt.h>
 #include <linux/ioport.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 #include <clocksource/samsung_pwm.h>
 #include <linux/platform_device.h>
 #include <linux/delay.h>
@@ -44,7 +45,6 @@
 #include <asm/mach/map.h>
 
 #include <mach/regs-gpio.h>
-#include <plat/regs-serial.h>
 #include <mach/dma.h>
 
 #include <plat/cpu.h>
@@ -240,7 +240,6 @@
 	} else {
 		samsung_cpu_id = s3c24xx_read_idcode_v4();
 	}
-	s3c24xx_init_cpu();
 
 	s3c_init_cpu(samsung_cpu_id, cpu_ids, ARRAY_SIZE(cpu_ids));
 
diff --git a/arch/arm/mach-s3c24xx/dma-s3c2410.c b/arch/arm/mach-s3c24xx/dma-s3c2410.c
index 30aa53f..09aa12d 100644
--- a/arch/arm/mach-s3c24xx/dma-s3c2410.c
+++ b/arch/arm/mach-s3c24xx/dma-s3c2410.c
@@ -16,6 +16,7 @@
 #include <linux/init.h>
 #include <linux/device.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 
 #include <mach/map.h>
 #include <mach/dma.h>
@@ -23,7 +24,6 @@
 #include <plat/cpu.h>
 #include <plat/dma-s3c24xx.h>
 
-#include <plat/regs-serial.h>
 #include <mach/regs-gpio.h>
 #include <plat/regs-dma.h>
 #include <mach/regs-lcd.h>
diff --git a/arch/arm/mach-s3c24xx/dma-s3c2412.c b/arch/arm/mach-s3c24xx/dma-s3c2412.c
index b7e0946..0c0106d 100644
--- a/arch/arm/mach-s3c24xx/dma-s3c2412.c
+++ b/arch/arm/mach-s3c24xx/dma-s3c2412.c
@@ -16,6 +16,7 @@
 #include <linux/init.h>
 #include <linux/device.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 #include <linux/io.h>
 
 #include <mach/dma.h>
@@ -23,7 +24,6 @@
 #include <plat/dma-s3c24xx.h>
 #include <plat/cpu.h>
 
-#include <plat/regs-serial.h>
 #include <mach/regs-gpio.h>
 #include <plat/regs-dma.h>
 #include <mach/regs-lcd.h>
diff --git a/arch/arm/mach-s3c24xx/dma-s3c2440.c b/arch/arm/mach-s3c24xx/dma-s3c2440.c
index cd25de2..2f8e8a3 100644
--- a/arch/arm/mach-s3c24xx/dma-s3c2440.c
+++ b/arch/arm/mach-s3c24xx/dma-s3c2440.c
@@ -16,6 +16,7 @@
 #include <linux/init.h>
 #include <linux/device.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 
 #include <mach/map.h>
 #include <mach/dma.h>
@@ -23,7 +24,6 @@
 #include <plat/dma-s3c24xx.h>
 #include <plat/cpu.h>
 
-#include <plat/regs-serial.h>
 #include <mach/regs-gpio.h>
 #include <plat/regs-dma.h>
 #include <mach/regs-lcd.h>
diff --git a/arch/arm/mach-s3c24xx/dma-s3c2443.c b/arch/arm/mach-s3c24xx/dma-s3c2443.c
index 95b9f75..f4096ec 100644
--- a/arch/arm/mach-s3c24xx/dma-s3c2443.c
+++ b/arch/arm/mach-s3c24xx/dma-s3c2443.c
@@ -16,6 +16,7 @@
 #include <linux/init.h>
 #include <linux/device.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 #include <linux/io.h>
 
 #include <mach/dma.h>
@@ -23,7 +24,6 @@
 #include <plat/dma-s3c24xx.h>
 #include <plat/cpu.h>
 
-#include <plat/regs-serial.h>
 #include <mach/regs-gpio.h>
 #include <plat/regs-dma.h>
 #include <mach/regs-lcd.h>
diff --git a/arch/arm/mach-s3c24xx/include/mach/debug-macro.S b/arch/arm/mach-s3c24xx/include/mach/debug-macro.S
index 2558952..2f39737 100644
--- a/arch/arm/mach-s3c24xx/include/mach/debug-macro.S
+++ b/arch/arm/mach-s3c24xx/include/mach/debug-macro.S
@@ -14,7 +14,7 @@
 
 #include <mach/map.h>
 #include <mach/regs-gpio.h>
-#include <plat/regs-serial.h>
+#include <linux/serial_s3c.h>
 
 #define S3C2410_UART1_OFF (0x4000)
 #define SHIFT_2440TXF (14-9)
diff --git a/arch/arm/plat-samsung/include/plat/rtc-core.h b/arch/arm/mach-s3c24xx/include/mach/rtc-core.h
similarity index 69%
rename from arch/arm/plat-samsung/include/plat/rtc-core.h
rename to arch/arm/mach-s3c24xx/include/mach/rtc-core.h
index 7b542f7..4d5f576 100644
--- a/arch/arm/plat-samsung/include/plat/rtc-core.h
+++ b/arch/arm/mach-s3c24xx/include/mach/rtc-core.h
@@ -1,5 +1,4 @@
-/* linux/arch/arm/plat-samsung/include/plat/rtc-core.h
- *
+/*
  * Copyright (c) 2011 Heiko Stuebner <heiko@sntech.de>
  *
  * Samsung RTC Controller core functions
@@ -9,19 +8,19 @@
  * published by the Free Software Foundation.
 */
 
-#ifndef __ASM_PLAT_RTC_CORE_H
-#define __ASM_PLAT_RTC_CORE_H __FILE__
+#ifndef __RTC_CORE_H
+#define __RTC_CORE_H __FILE__
 
 /* These functions are only for use with the core support code, such as
  * the cpu specific initialisation code
  */
 
+extern struct platform_device s3c_device_rtc;
+
 /* re-define device name depending on support. */
 static inline void s3c_rtc_setname(char *name)
 {
-#if defined(CONFIG_S3C_DEV_RTC) || defined(CONFIG_PLAT_S3C24XX)
 	s3c_device_rtc.name = name;
-#endif
 }
 
-#endif /* __ASM_PLAT_RTC_CORE_H */
+#endif /* __RTC_CORE_H */
diff --git a/arch/arm/mach-s3c24xx/include/mach/tick.h b/arch/arm/mach-s3c24xx/include/mach/tick.h
deleted file mode 100644
index 544da41..0000000
--- a/arch/arm/mach-s3c24xx/include/mach/tick.h
+++ /dev/null
@@ -1,15 +0,0 @@
-/* linux/arch/arm/mach-s3c2410/include/mach/tick.h
- *
- * Copyright 2008 Simtec Electronics
- *      Ben Dooks <ben@simtec.co.uk>
- *      http://armlinux.simtec.co.uk/
- *
- * S3C2410 - timer tick support
- */
-
-#define SRCPND_TIMER4 (1<<(IRQ_TIMER4 - IRQ_EINT0))
-
-static inline int s3c24xx_ostimer_pending(void)
-{
-	return __raw_readl(S3C2410_SRCPND) & SRCPND_TIMER4;
-}
diff --git a/arch/arm/mach-s3c24xx/include/mach/timex.h b/arch/arm/mach-s3c24xx/include/mach/timex.h
deleted file mode 100644
index fe9ca1f..0000000
--- a/arch/arm/mach-s3c24xx/include/mach/timex.h
+++ /dev/null
@@ -1,24 +0,0 @@
-/* arch/arm/mach-s3c2410/include/mach/timex.h
- *
- * Copyright (c) 2003-2005 Simtec Electronics
- *	Ben Dooks <ben@simtec.co.uk>
- *
- * S3C2410 - time parameters
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#ifndef __ASM_ARCH_TIMEX_H
-#define __ASM_ARCH_TIMEX_H
-
-/* CLOCK_TICK_RATE needs to be evaluatable by the cpp, so making it
- * a variable is useless. It seems as long as we make our timers an
- * exact multiple of HZ, any value that makes a 1->1 correspondence
- * for the time conversion functions to/from jiffies is acceptable.
-*/
-
-#define CLOCK_TICK_RATE 12000000
-
-#endif /* __ASM_ARCH_TIMEX_H */
diff --git a/arch/arm/mach-s3c24xx/mach-amlm5900.c b/arch/arm/mach-s3c24xx/mach-amlm5900.c
index 284ea1f..8ac9554 100644
--- a/arch/arm/mach-s3c24xx/mach-amlm5900.c
+++ b/arch/arm/mach-s3c24xx/mach-amlm5900.c
@@ -37,6 +37,7 @@
 #include <linux/platform_device.h>
 #include <linux/proc_fs.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 #include <linux/io.h>
 
 #include <asm/mach/arch.h>
@@ -49,7 +50,6 @@
 #include <asm/mach-types.h>
 #include <mach/fb.h>
 
-#include <plat/regs-serial.h>
 #include <mach/regs-lcd.h>
 #include <mach/regs-gpio.h>
 #include <mach/gpio-samsung.h>
diff --git a/arch/arm/mach-s3c24xx/mach-anubis.c b/arch/arm/mach-s3c24xx/mach-anubis.c
index 2a16f8f..81a270a 100644
--- a/arch/arm/mach-s3c24xx/mach-anubis.c
+++ b/arch/arm/mach-s3c24xx/mach-anubis.c
@@ -17,6 +17,7 @@
 #include <linux/init.h>
 #include <linux/gpio.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 #include <linux/platform_device.h>
 #include <linux/ata_platform.h>
 #include <linux/i2c.h>
@@ -32,7 +33,6 @@
 #include <asm/irq.h>
 #include <asm/mach-types.h>
 
-#include <plat/regs-serial.h>
 #include <mach/regs-gpio.h>
 #include <mach/regs-lcd.h>
 #include <mach/gpio-samsung.h>
diff --git a/arch/arm/mach-s3c24xx/mach-at2440evb.c b/arch/arm/mach-s3c24xx/mach-at2440evb.c
index 6beab67..d8f6bb1 100644
--- a/arch/arm/mach-s3c24xx/mach-at2440evb.c
+++ b/arch/arm/mach-s3c24xx/mach-at2440evb.c
@@ -21,6 +21,7 @@
 #include <linux/init.h>
 #include <linux/io.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 #include <linux/dm9000.h>
 #include <linux/platform_device.h>
 
@@ -33,7 +34,6 @@
 #include <asm/irq.h>
 #include <asm/mach-types.h>
 
-#include <plat/regs-serial.h>
 #include <mach/regs-gpio.h>
 #include <mach/regs-lcd.h>
 #include <mach/gpio-samsung.h>
diff --git a/arch/arm/mach-s3c24xx/mach-bast.c b/arch/arm/mach-s3c24xx/mach-bast.c
index 981ba1e..e371ff5 100644
--- a/arch/arm/mach-s3c24xx/mach-bast.c
+++ b/arch/arm/mach-s3c24xx/mach-bast.c
@@ -19,6 +19,7 @@
 #include <linux/gpio.h>
 #include <linux/syscore_ops.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 #include <linux/platform_device.h>
 #include <linux/dm9000.h>
 #include <linux/ata_platform.h>
@@ -55,7 +56,6 @@
 #include <plat/cpu-freq.h>
 #include <plat/devs.h>
 #include <plat/gpio-cfg.h>
-#include <plat/regs-serial.h>
 #include <plat/samsung-time.h>
 
 #include "bast.h"
diff --git a/arch/arm/mach-s3c24xx/mach-gta02.c b/arch/arm/mach-s3c24xx/mach-gta02.c
index d9170e9..8e05813 100644
--- a/arch/arm/mach-s3c24xx/mach-gta02.c
+++ b/arch/arm/mach-s3c24xx/mach-gta02.c
@@ -35,6 +35,7 @@
 #include <linux/workqueue.h>
 #include <linux/platform_device.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 #include <linux/input.h>
 #include <linux/io.h>
 #include <linux/i2c.h>
@@ -81,7 +82,6 @@
 #include <plat/devs.h>
 #include <plat/gpio-cfg.h>
 #include <plat/pm.h>
-#include <plat/regs-serial.h>
 #include <plat/samsung-time.h>
 
 #include "common.h"
diff --git a/arch/arm/mach-s3c24xx/mach-h1940.c b/arch/arm/mach-s3c24xx/mach-h1940.c
index de08321..e453acd 100644
--- a/arch/arm/mach-s3c24xx/mach-h1940.c
+++ b/arch/arm/mach-s3c24xx/mach-h1940.c
@@ -19,6 +19,7 @@
 #include <linux/init.h>
 #include <linux/device.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 #include <linux/platform_device.h>
 #include <linux/io.h>
 #include <linux/gpio.h>
@@ -62,7 +63,6 @@
 #include <plat/gpio-cfg.h>
 #include <plat/pll.h>
 #include <plat/pm.h>
-#include <plat/regs-serial.h>
 #include <plat/samsung-time.h>
 
 #include "common.h"
diff --git a/arch/arm/mach-s3c24xx/mach-jive.c b/arch/arm/mach-s3c24xx/mach-jive.c
index 67cb8e9..5faa723 100644
--- a/arch/arm/mach-s3c24xx/mach-jive.c
+++ b/arch/arm/mach-s3c24xx/mach-jive.c
@@ -19,6 +19,7 @@
 #include <linux/gpio.h>
 #include <linux/syscore_ops.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 #include <linux/platform_device.h>
 #include <linux/i2c.h>
 
@@ -31,7 +32,6 @@
 #include <asm/mach/map.h>
 #include <asm/mach/irq.h>
 
-#include <plat/regs-serial.h>
 #include <linux/platform_data/mtd-nand-s3c2410.h>
 #include <linux/platform_data/i2c-s3c2410.h>
 
diff --git a/arch/arm/mach-s3c24xx/mach-mini2440.c b/arch/arm/mach-s3c24xx/mach-mini2440.c
index 1f15597..9e57fd9 100644
--- a/arch/arm/mach-s3c24xx/mach-mini2440.c
+++ b/arch/arm/mach-s3c24xx/mach-mini2440.c
@@ -23,6 +23,7 @@
 #include <linux/input.h>
 #include <linux/io.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 #include <linux/dm9000.h>
 #include <linux/platform_data/at24.h>
 #include <linux/platform_device.h>
@@ -37,7 +38,6 @@
 #include <mach/fb.h>
 #include <asm/mach-types.h>
 
-#include <plat/regs-serial.h>
 #include <mach/regs-gpio.h>
 #include <linux/platform_data/leds-s3c24xx.h>
 #include <mach/regs-lcd.h>
diff --git a/arch/arm/mach-s3c24xx/mach-n30.c b/arch/arm/mach-s3c24xx/mach-n30.c
index 997684f..4cccaad 100644
--- a/arch/arm/mach-s3c24xx/mach-n30.c
+++ b/arch/arm/mach-s3c24xx/mach-n30.c
@@ -24,6 +24,7 @@
 #include <linux/interrupt.h>
 #include <linux/platform_device.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 #include <linux/timer.h>
 #include <linux/io.h>
 #include <linux/mmc/host.h>
@@ -43,7 +44,6 @@
 #include <asm/mach/map.h>
 
 #include <linux/platform_data/i2c-s3c2410.h>
-#include <plat/regs-serial.h>
 
 #include <plat/clock.h>
 #include <plat/cpu.h>
diff --git a/arch/arm/mach-s3c24xx/mach-nexcoder.c b/arch/arm/mach-s3c24xx/mach-nexcoder.c
index 575d28c..3066851 100644
--- a/arch/arm/mach-s3c24xx/mach-nexcoder.c
+++ b/arch/arm/mach-s3c24xx/mach-nexcoder.c
@@ -21,6 +21,7 @@
 #include <linux/gpio.h>
 #include <linux/string.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 #include <linux/platform_device.h>
 #include <linux/io.h>
 
@@ -38,7 +39,6 @@
 //#include <asm/debug-ll.h>
 #include <mach/regs-gpio.h>
 #include <mach/gpio-samsung.h>
-#include <plat/regs-serial.h>
 #include <linux/platform_data/i2c-s3c2410.h>
 
 #include <plat/gpio-cfg.h>
diff --git a/arch/arm/mach-s3c24xx/mach-osiris.c b/arch/arm/mach-s3c24xx/mach-osiris.c
index f84f2a4..a4ae4bb 100644
--- a/arch/arm/mach-s3c24xx/mach-osiris.c
+++ b/arch/arm/mach-s3c24xx/mach-osiris.c
@@ -18,6 +18,7 @@
 #include <linux/device.h>
 #include <linux/syscore_ops.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 #include <linux/clk.h>
 #include <linux/i2c.h>
 #include <linux/io.h>
@@ -44,7 +45,6 @@
 #include <plat/cpu-freq.h>
 #include <plat/devs.h>
 #include <plat/gpio-cfg.h>
-#include <plat/regs-serial.h>
 #include <plat/samsung-time.h>
 
 #include <mach/hardware.h>
diff --git a/arch/arm/mach-s3c24xx/mach-otom.c b/arch/arm/mach-s3c24xx/mach-otom.c
index 7e16b07..bdb3faa 100644
--- a/arch/arm/mach-s3c24xx/mach-otom.c
+++ b/arch/arm/mach-s3c24xx/mach-otom.c
@@ -15,6 +15,7 @@
 #include <linux/timer.h>
 #include <linux/init.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 #include <linux/platform_device.h>
 #include <linux/io.h>
 
@@ -32,7 +33,6 @@
 #include <plat/clock.h>
 #include <plat/cpu.h>
 #include <plat/devs.h>
-#include <plat/regs-serial.h>
 #include <plat/samsung-time.h>
 
 #include "common.h"
diff --git a/arch/arm/mach-s3c24xx/mach-qt2410.c b/arch/arm/mach-s3c24xx/mach-qt2410.c
index b534b76..8c12787 100644
--- a/arch/arm/mach-s3c24xx/mach-qt2410.c
+++ b/arch/arm/mach-s3c24xx/mach-qt2410.c
@@ -31,6 +31,7 @@
 #include <linux/device.h>
 #include <linux/platform_device.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 #include <linux/spi/spi.h>
 #include <linux/spi/spi_gpio.h>
 #include <linux/io.h>
@@ -49,7 +50,6 @@
 
 #include <linux/platform_data/leds-s3c24xx.h>
 #include <mach/regs-lcd.h>
-#include <plat/regs-serial.h>
 #include <mach/fb.h>
 #include <linux/platform_data/mtd-nand-s3c2410.h>
 #include <linux/platform_data/usb-s3c2410_udc.h>
diff --git a/arch/arm/mach-s3c24xx/mach-rx1950.c b/arch/arm/mach-s3c24xx/mach-rx1950.c
index 0a5456c..afb784e 100644
--- a/arch/arm/mach-s3c24xx/mach-rx1950.c
+++ b/arch/arm/mach-s3c24xx/mach-rx1950.c
@@ -21,6 +21,7 @@
 #include <linux/gpio.h>
 #include <linux/platform_device.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 #include <linux/input.h>
 #include <linux/gpio_keys.h>
 #include <linux/device.h>
@@ -57,7 +58,6 @@
 #include <plat/cpu.h>
 #include <plat/devs.h>
 #include <plat/pm.h>
-#include <plat/regs-serial.h>
 #include <plat/samsung-time.h>
 #include <plat/gpio-cfg.h>
 
diff --git a/arch/arm/mach-s3c24xx/mach-rx3715.c b/arch/arm/mach-s3c24xx/mach-rx3715.c
index b36edce..e6535ce 100644
--- a/arch/arm/mach-s3c24xx/mach-rx3715.c
+++ b/arch/arm/mach-s3c24xx/mach-rx3715.c
@@ -23,6 +23,7 @@
 #include <linux/device.h>
 #include <linux/platform_device.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 #include <linux/serial.h>
 #include <linux/io.h>
 #include <linux/mtd/mtd.h>
@@ -49,7 +50,6 @@
 #include <plat/cpu.h>
 #include <plat/devs.h>
 #include <plat/pm.h>
-#include <plat/regs-serial.h>
 #include <plat/samsung-time.h>
 
 #include "common.h"
diff --git a/arch/arm/mach-s3c24xx/mach-s3c2416-dt.c b/arch/arm/mach-s3c24xx/mach-s3c2416-dt.c
index f50454a..70f0900 100644
--- a/arch/arm/mach-s3c24xx/mach-s3c2416-dt.c
+++ b/arch/arm/mach-s3c24xx/mach-s3c2416-dt.c
@@ -19,13 +19,13 @@
 #include <linux/irqchip.h>
 #include <linux/of_platform.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 
 #include <asm/mach/arch.h>
 #include <mach/map.h>
 
 #include <plat/cpu.h>
 #include <plat/pm.h>
-#include <plat/regs-serial.h>
 
 #include "common.h"
 
diff --git a/arch/arm/mach-s3c24xx/mach-smdk2410.c b/arch/arm/mach-s3c24xx/mach-smdk2410.c
index a773789..f32924e 100644
--- a/arch/arm/mach-s3c24xx/mach-smdk2410.c
+++ b/arch/arm/mach-s3c24xx/mach-smdk2410.c
@@ -35,6 +35,7 @@
 #include <linux/timer.h>
 #include <linux/init.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 #include <linux/platform_device.h>
 #include <linux/io.h>
 
@@ -46,7 +47,6 @@
 #include <asm/irq.h>
 #include <asm/mach-types.h>
 
-#include <plat/regs-serial.h>
 #include <linux/platform_data/i2c-s3c2410.h>
 
 #include <plat/devs.h>
diff --git a/arch/arm/mach-s3c24xx/mach-smdk2413.c b/arch/arm/mach-s3c24xx/mach-smdk2413.c
index f5bc721..233fe52 100644
--- a/arch/arm/mach-s3c24xx/mach-smdk2413.c
+++ b/arch/arm/mach-s3c24xx/mach-smdk2413.c
@@ -19,6 +19,7 @@
 #include <linux/init.h>
 #include <linux/gpio.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 #include <linux/platform_device.h>
 #include <linux/io.h>
 
@@ -33,7 +34,6 @@
 #include <asm/mach-types.h>
 
 //#include <asm/debug-ll.h>
-#include <plat/regs-serial.h>
 #include <mach/regs-gpio.h>
 #include <mach/regs-lcd.h>
 
diff --git a/arch/arm/mach-s3c24xx/mach-smdk2416.c b/arch/arm/mach-s3c24xx/mach-smdk2416.c
index 12023ca..b3b54d8 100644
--- a/arch/arm/mach-s3c24xx/mach-smdk2416.c
+++ b/arch/arm/mach-s3c24xx/mach-smdk2416.c
@@ -18,6 +18,7 @@
 #include <linux/timer.h>
 #include <linux/init.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 #include <linux/platform_device.h>
 #include <linux/io.h>
 #include <linux/mtd/partitions.h>
@@ -34,7 +35,6 @@
 #include <asm/irq.h>
 #include <asm/mach-types.h>
 
-#include <plat/regs-serial.h>
 #include <mach/regs-gpio.h>
 #include <mach/regs-lcd.h>
 #include <mach/regs-s3c2443-clock.h>
diff --git a/arch/arm/mach-s3c24xx/mach-smdk2440.c b/arch/arm/mach-s3c24xx/mach-smdk2440.c
index de2e5d3..d071dcf 100644
--- a/arch/arm/mach-s3c24xx/mach-smdk2440.c
+++ b/arch/arm/mach-s3c24xx/mach-smdk2440.c
@@ -20,6 +20,7 @@
 #include <linux/timer.h>
 #include <linux/init.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 #include <linux/platform_device.h>
 #include <linux/io.h>
 
@@ -31,7 +32,6 @@
 #include <asm/irq.h>
 #include <asm/mach-types.h>
 
-#include <plat/regs-serial.h>
 #include <mach/regs-gpio.h>
 #include <mach/regs-lcd.h>
 
diff --git a/arch/arm/mach-s3c24xx/mach-smdk2443.c b/arch/arm/mach-s3c24xx/mach-smdk2443.c
index d9933fc..06c4d77 100644
--- a/arch/arm/mach-s3c24xx/mach-smdk2443.c
+++ b/arch/arm/mach-s3c24xx/mach-smdk2443.c
@@ -20,6 +20,7 @@
 #include <linux/timer.h>
 #include <linux/init.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 #include <linux/platform_device.h>
 #include <linux/io.h>
 
@@ -31,7 +32,6 @@
 #include <asm/irq.h>
 #include <asm/mach-types.h>
 
-#include <plat/regs-serial.h>
 #include <mach/regs-gpio.h>
 #include <mach/regs-lcd.h>
 
diff --git a/arch/arm/mach-s3c24xx/mach-tct_hammer.c b/arch/arm/mach-s3c24xx/mach-tct_hammer.c
index 7fad8f0..4108b2f 100644
--- a/arch/arm/mach-s3c24xx/mach-tct_hammer.c
+++ b/arch/arm/mach-s3c24xx/mach-tct_hammer.c
@@ -33,6 +33,7 @@
 #include <linux/device.h>
 #include <linux/platform_device.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 #include <linux/io.h>
 
 #include <asm/mach/arch.h>
@@ -44,7 +45,6 @@
 #include <asm/irq.h>
 #include <asm/mach-types.h>
 
-#include <plat/regs-serial.h>
 #include <linux/platform_data/i2c-s3c2410.h>
 #include <plat/devs.h>
 #include <plat/cpu.h>
diff --git a/arch/arm/mach-s3c24xx/mach-vr1000.c b/arch/arm/mach-s3c24xx/mach-vr1000.c
index 755df48..1cc5b1b 100644
--- a/arch/arm/mach-s3c24xx/mach-vr1000.c
+++ b/arch/arm/mach-s3c24xx/mach-vr1000.c
@@ -25,6 +25,7 @@
 #include <linux/tty.h>
 #include <linux/serial_8250.h>
 #include <linux/serial_reg.h>
+#include <linux/serial_s3c.h>
 #include <linux/io.h>
 
 #include <asm/mach/arch.h>
@@ -45,7 +46,6 @@
 #include <plat/clock.h>
 #include <plat/cpu.h>
 #include <plat/devs.h>
-#include <plat/regs-serial.h>
 #include <plat/samsung-time.h>
 
 #include "bast.h"
diff --git a/arch/arm/mach-s3c24xx/mach-vstms.c b/arch/arm/mach-s3c24xx/mach-vstms.c
index f7ec9c5..40868c0 100644
--- a/arch/arm/mach-s3c24xx/mach-vstms.c
+++ b/arch/arm/mach-s3c24xx/mach-vstms.c
@@ -16,6 +16,7 @@
 #include <linux/timer.h>
 #include <linux/init.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 #include <linux/platform_device.h>
 #include <linux/io.h>
 #include <linux/mtd/mtd.h>
@@ -32,7 +33,6 @@
 #include <asm/irq.h>
 #include <asm/mach-types.h>
 
-#include <plat/regs-serial.h>
 #include <mach/regs-gpio.h>
 #include <mach/regs-lcd.h>
 
diff --git a/arch/arm/mach-s3c24xx/pm.c b/arch/arm/mach-s3c24xx/pm.c
index 052ca23..68ea5b7 100644
--- a/arch/arm/mach-s3c24xx/pm.c
+++ b/arch/arm/mach-s3c24xx/pm.c
@@ -33,9 +33,9 @@
 #include <linux/gpio.h>
 #include <linux/interrupt.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 #include <linux/io.h>
 
-#include <plat/regs-serial.h>
 #include <mach/regs-clock.h>
 #include <mach/regs-gpio.h>
 #include <mach/regs-irq.h>
diff --git a/arch/arm/mach-s3c24xx/s3c2410.c b/arch/arm/mach-s3c24xx/s3c2410.c
index ffb92cbc..04b58cb 100644
--- a/arch/arm/mach-s3c24xx/s3c2410.c
+++ b/arch/arm/mach-s3c24xx/s3c2410.c
@@ -21,6 +21,7 @@
 #include <linux/device.h>
 #include <linux/syscore_ops.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 #include <linux/platform_device.h>
 #include <linux/reboot.h>
 #include <linux/io.h>
@@ -37,7 +38,6 @@
 #include <plat/cpu-freq.h>
 
 #include <mach/regs-clock.h>
-#include <plat/regs-serial.h>
 
 #include <plat/cpu.h>
 #include <plat/devs.h>
diff --git a/arch/arm/mach-s3c24xx/s3c2412.c b/arch/arm/mach-s3c24xx/s3c2412.c
index 0251650c..657cbac 100644
--- a/arch/arm/mach-s3c24xx/s3c2412.c
+++ b/arch/arm/mach-s3c24xx/s3c2412.c
@@ -20,6 +20,7 @@
 #include <linux/device.h>
 #include <linux/syscore_ops.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 #include <linux/platform_device.h>
 #include <linux/io.h>
 #include <linux/reboot.h>
@@ -43,7 +44,6 @@
 #include <plat/nand-core.h>
 #include <plat/pll.h>
 #include <plat/pm.h>
-#include <plat/regs-serial.h>
 #include <plat/regs-spi.h>
 
 #include "common.h"
diff --git a/arch/arm/mach-s3c24xx/s3c2416.c b/arch/arm/mach-s3c24xx/s3c2416.c
index 8e01b4f..9fe260a 100644
--- a/arch/arm/mach-s3c24xx/s3c2416.c
+++ b/arch/arm/mach-s3c24xx/s3c2416.c
@@ -48,6 +48,7 @@
 #include <asm/system_misc.h>
 
 #include <mach/regs-s3c2443-clock.h>
+#include <mach/rtc-core.h>
 
 #include <plat/gpio-core.h>
 #include <plat/gpio-cfg.h>
@@ -61,7 +62,6 @@
 #include <plat/fb-core.h>
 #include <plat/nand-core.h>
 #include <plat/adc-core.h>
-#include <plat/rtc-core.h>
 #include <plat/spi-core.h>
 
 #include "common.h"
diff --git a/arch/arm/mach-s3c24xx/s3c2443.c b/arch/arm/mach-s3c24xx/s3c2443.c
index 886c214..c7a804d 100644
--- a/arch/arm/mach-s3c24xx/s3c2443.c
+++ b/arch/arm/mach-s3c24xx/s3c2443.c
@@ -34,6 +34,7 @@
 #include <asm/system_misc.h>
 
 #include <mach/regs-s3c2443-clock.h>
+#include <mach/rtc-core.h>
 
 #include <plat/gpio-core.h>
 #include <plat/gpio-cfg.h>
@@ -43,7 +44,6 @@
 #include <plat/fb-core.h>
 #include <plat/nand-core.h>
 #include <plat/adc-core.h>
-#include <plat/rtc-core.h>
 #include <plat/spi-core.h>
 
 static struct map_desc s3c2443_iodesc[] __initdata = {
diff --git a/arch/arm/mach-s3c24xx/s3c244x.c b/arch/arm/mach-s3c24xx/s3c244x.c
index 911b555..fe30ebb2 100644
--- a/arch/arm/mach-s3c24xx/s3c244x.c
+++ b/arch/arm/mach-s3c24xx/s3c244x.c
@@ -17,6 +17,7 @@
 #include <linux/timer.h>
 #include <linux/init.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 #include <linux/platform_device.h>
 #include <linux/reboot.h>
 #include <linux/device.h>
@@ -35,7 +36,6 @@
 #include <plat/cpu-freq.h>
 
 #include <mach/regs-clock.h>
-#include <plat/regs-serial.h>
 #include <mach/regs-gpio.h>
 
 #include <plat/clock.h>
diff --git a/arch/arm/mach-s3c24xx/sleep-s3c2410.S b/arch/arm/mach-s3c24xx/sleep-s3c2410.S
index dd47c8f..c9b9122 100644
--- a/arch/arm/mach-s3c24xx/sleep-s3c2410.S
+++ b/arch/arm/mach-s3c24xx/sleep-s3c2410.S
@@ -25,13 +25,13 @@
 */
 
 #include <linux/linkage.h>
+#include <linux/serial_s3c.h>
 #include <asm/assembler.h>
 #include <mach/hardware.h>
 #include <mach/map.h>
 
 #include <mach/regs-gpio.h>
 #include <mach/regs-clock.h>
-#include <plat/regs-serial.h>
 
 #include "regs-mem.h"
 
diff --git a/arch/arm/mach-s3c24xx/sleep.S b/arch/arm/mach-s3c24xx/sleep.S
index 7f378b6..d833d61 100644
--- a/arch/arm/mach-s3c24xx/sleep.S
+++ b/arch/arm/mach-s3c24xx/sleep.S
@@ -25,13 +25,13 @@
 */
 
 #include <linux/linkage.h>
+#include <linux/serial_s3c.h>
 #include <asm/assembler.h>
 #include <mach/hardware.h>
 #include <mach/map.h>
 
 #include <mach/regs-gpio.h>
 #include <mach/regs-clock.h>
-#include <plat/regs-serial.h>
 
 /* CONFIG_DEBUG_RESUME is dangerous if your bootloader does not
  * reset the UART configuration, only enable if you really need this!
diff --git a/arch/arm/mach-s3c64xx/common.c b/arch/arm/mach-s3c64xx/common.c
index 76ab595..5c45aae 100644
--- a/arch/arm/mach-s3c64xx/common.c
+++ b/arch/arm/mach-s3c64xx/common.c
@@ -25,6 +25,7 @@
 #include <linux/interrupt.h>
 #include <linux/ioport.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 #include <linux/platform_device.h>
 #include <linux/reboot.h>
 #include <linux/io.h>
@@ -50,7 +51,6 @@
 #include <plat/irq-uart.h>
 #include <plat/pwm-core.h>
 #include <plat/regs-irqtype.h>
-#include <plat/regs-serial.h>
 #include <plat/watchdog-reset.h>
 
 #include "common.h"
diff --git a/arch/arm/mach-s3c64xx/include/mach/debug-macro.S b/arch/arm/mach-s3c64xx/include/mach/debug-macro.S
index dd9ccca..c9b9532 100644
--- a/arch/arm/mach-s3c64xx/include/mach/debug-macro.S
+++ b/arch/arm/mach-s3c64xx/include/mach/debug-macro.S
@@ -12,8 +12,8 @@
 
 /* pull in the relevant register and map files. */
 
+#include <linux/serial_s3c.h>
 #include <mach/map.h>
-#include <plat/regs-serial.h>
 
 	/* note, for the boot process to work we have to keep the UART
 	 * virtual address aligned to an 1MiB boundary for the L1
diff --git a/arch/arm/mach-s3c64xx/include/mach/tick.h b/arch/arm/mach-s3c64xx/include/mach/tick.h
deleted file mode 100644
index db9c1b1..0000000
--- a/arch/arm/mach-s3c64xx/include/mach/tick.h
+++ /dev/null
@@ -1,31 +0,0 @@
-/* linux/arch/arm/mach-s3c6400/include/mach/tick.h
- *
- * Copyright 2008 Openmoko, Inc.
- * Copyright 2008 Simtec Electronics
- *	http://armlinux.simtec.co.uk/
- *	Ben Dooks <ben@simtec.co.uk>
- *
- * S3C64XX - Timer tick support definitions
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#ifndef __ASM_ARCH_TICK_H
-#define __ASM_ARCH_TICK_H __FILE__
-
-#include <linux/irqchip/arm-vic.h>
-
-/* note, the timer interrutps turn up in 2 places, the vic and then
- * the timer block. We take the VIC as the base at the moment.
- */
-static inline u32 s3c24xx_ostimer_pending(void)
-{
-	u32 pend = __raw_readl(VA_VIC0 + VIC_RAW_STATUS);
-	return pend & 1 << (IRQ_TIMER4_VIC - S3C64XX_IRQ_VIC0(0));
-}
-
-#define TICK_MAX	(0xffffffff)
-
-#endif /* __ASM_ARCH_6400_TICK_H */
diff --git a/arch/arm/mach-s3c64xx/include/mach/timex.h b/arch/arm/mach-s3c64xx/include/mach/timex.h
deleted file mode 100644
index fb2e8cd..0000000
--- a/arch/arm/mach-s3c64xx/include/mach/timex.h
+++ /dev/null
@@ -1,24 +0,0 @@
-/* arch/arm/mach-s3c64xx/include/mach/timex.h
- *
- * Copyright (c) 2003-2005 Simtec Electronics
- *	Ben Dooks <ben@simtec.co.uk>
- *
- * S3C6400 - time parameters
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#ifndef __ASM_ARCH_TIMEX_H
-#define __ASM_ARCH_TIMEX_H
-
-/* CLOCK_TICK_RATE needs to be evaluatable by the cpp, so making it
- * a variable is useless. It seems as long as we make our timers an
- * exact multiple of HZ, any value that makes a 1->1 correspondence
- * for the time conversion functions to/from jiffies is acceptable.
-*/
-
-#define CLOCK_TICK_RATE 12000000
-
-#endif /* __ASM_ARCH_TIMEX_H */
diff --git a/arch/arm/mach-s3c64xx/irq-pm.c b/arch/arm/mach-s3c64xx/irq-pm.c
index 1649c0d..a61247b 100644
--- a/arch/arm/mach-s3c64xx/irq-pm.c
+++ b/arch/arm/mach-s3c64xx/irq-pm.c
@@ -20,13 +20,13 @@
 #include <linux/syscore_ops.h>
 #include <linux/interrupt.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 #include <linux/irq.h>
 #include <linux/io.h>
 #include <linux/of.h>
 
 #include <mach/map.h>
 
-#include <plat/regs-serial.h>
 #include <mach/regs-gpio.h>
 #include <plat/cpu.h>
 #include <plat/pm.h>
diff --git a/arch/arm/mach-s3c64xx/mach-anw6410.c b/arch/arm/mach-s3c64xx/mach-anw6410.c
index ddeb0e5..55eb6a6 100644
--- a/arch/arm/mach-s3c64xx/mach-anw6410.c
+++ b/arch/arm/mach-s3c64xx/mach-anw6410.c
@@ -20,6 +20,7 @@
 #include <linux/timer.h>
 #include <linux/init.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 #include <linux/platform_device.h>
 #include <linux/io.h>
 #include <linux/i2c.h>
@@ -41,7 +42,6 @@
 #include <asm/irq.h>
 #include <asm/mach-types.h>
 
-#include <plat/regs-serial.h>
 #include <linux/platform_data/i2c-s3c2410.h>
 #include <plat/fb.h>
 
diff --git a/arch/arm/mach-s3c64xx/mach-crag6410.c b/arch/arm/mach-s3c64xx/mach-crag6410.c
index 3df3c37..4b0199f 100644
--- a/arch/arm/mach-s3c64xx/mach-crag6410.c
+++ b/arch/arm/mach-s3c64xx/mach-crag6410.c
@@ -14,6 +14,7 @@
 #include <linux/kernel.h>
 #include <linux/list.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 #include <linux/platform_device.h>
 #include <linux/fb.h>
 #include <linux/io.h>
@@ -51,7 +52,6 @@
 #include <mach/regs-gpio.h>
 #include <mach/gpio-samsung.h>
 
-#include <plat/regs-serial.h>
 #include <plat/fb.h>
 #include <plat/sdhci.h>
 #include <plat/gpio-cfg.h>
diff --git a/arch/arm/mach-s3c64xx/mach-hmt.c b/arch/arm/mach-s3c64xx/mach-hmt.c
index 0431016..72cee08 100644
--- a/arch/arm/mach-s3c64xx/mach-hmt.c
+++ b/arch/arm/mach-s3c64xx/mach-hmt.c
@@ -11,6 +11,7 @@
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 #include <linux/platform_device.h>
 #include <linux/io.h>
 #include <linux/i2c.h>
@@ -33,7 +34,6 @@
 #include <asm/irq.h>
 #include <asm/mach-types.h>
 
-#include <plat/regs-serial.h>
 #include <linux/platform_data/i2c-s3c2410.h>
 #include <mach/gpio-samsung.h>
 #include <plat/fb.h>
diff --git a/arch/arm/mach-s3c64xx/mach-mini6410.c b/arch/arm/mach-s3c64xx/mach-mini6410.c
index 8d553a4..9cbc076 100644
--- a/arch/arm/mach-s3c64xx/mach-mini6410.c
+++ b/arch/arm/mach-s3c64xx/mach-mini6410.c
@@ -22,6 +22,7 @@
 #include <linux/mtd/mtd.h>
 #include <linux/mtd/partitions.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 #include <linux/types.h>
 
 #include <asm/mach-types.h>
@@ -38,7 +39,6 @@
 #include <plat/fb.h>
 #include <linux/platform_data/mtd-nand-s3c2410.h>
 #include <linux/platform_data/mmc-sdhci-s3c.h>
-#include <plat/regs-serial.h>
 #include <plat/sdhci.h>
 #include <linux/platform_data/touchscreen-s3c2410.h>
 
diff --git a/arch/arm/mach-s3c64xx/mach-ncp.c b/arch/arm/mach-s3c64xx/mach-ncp.c
index 2067b0b..67f06a9 100644
--- a/arch/arm/mach-s3c64xx/mach-ncp.c
+++ b/arch/arm/mach-s3c64xx/mach-ncp.c
@@ -16,6 +16,7 @@
 #include <linux/timer.h>
 #include <linux/init.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 #include <linux/platform_device.h>
 #include <linux/io.h>
 #include <linux/i2c.h>
@@ -36,7 +37,6 @@
 #include <asm/irq.h>
 #include <asm/mach-types.h>
 
-#include <plat/regs-serial.h>
 #include <linux/platform_data/i2c-s3c2410.h>
 #include <plat/fb.h>
 
diff --git a/arch/arm/mach-s3c64xx/mach-real6410.c b/arch/arm/mach-s3c64xx/mach-real6410.c
index 5152026..fbad2af 100644
--- a/arch/arm/mach-s3c64xx/mach-real6410.c
+++ b/arch/arm/mach-s3c64xx/mach-real6410.c
@@ -23,6 +23,7 @@
 #include <linux/mtd/partitions.h>
 #include <linux/platform_device.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 #include <linux/types.h>
 
 #include <asm/mach-types.h>
@@ -38,7 +39,6 @@
 #include <plat/devs.h>
 #include <plat/fb.h>
 #include <linux/platform_data/mtd-nand-s3c2410.h>
-#include <plat/regs-serial.h>
 #include <linux/platform_data/touchscreen-s3c2410.h>
 
 #include <video/platform_lcd.h>
diff --git a/arch/arm/mach-s3c64xx/mach-smartq.c b/arch/arm/mach-s3c64xx/mach-smartq.c
index 6e72bd5..78dd6f7 100644
--- a/arch/arm/mach-s3c64xx/mach-smartq.c
+++ b/arch/arm/mach-s3c64xx/mach-smartq.c
@@ -16,6 +16,7 @@
 #include <linux/platform_device.h>
 #include <linux/pwm_backlight.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 #include <linux/spi/spi_gpio.h>
 #include <linux/usb/gpio_vbus.h>
 #include <linux/platform_data/s3c-hsotg.h>
@@ -33,7 +34,6 @@
 #include <linux/platform_data/i2c-s3c2410.h>
 #include <plat/gpio-cfg.h>
 #include <linux/platform_data/hwmon-s3c.h>
-#include <plat/regs-serial.h>
 #include <linux/platform_data/usb-ohci-s3c2410.h>
 #include <plat/sdhci.h>
 #include <linux/platform_data/touchscreen-s3c2410.h>
diff --git a/arch/arm/mach-s3c64xx/mach-smdk6400.c b/arch/arm/mach-s3c64xx/mach-smdk6400.c
index 150f55f..c85d1cb 100644
--- a/arch/arm/mach-s3c64xx/mach-smdk6400.c
+++ b/arch/arm/mach-s3c64xx/mach-smdk6400.c
@@ -16,6 +16,7 @@
 #include <linux/timer.h>
 #include <linux/init.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 #include <linux/platform_device.h>
 #include <linux/i2c.h>
 #include <linux/io.h>
@@ -29,8 +30,6 @@
 #include <mach/hardware.h>
 #include <mach/map.h>
 
-#include <plat/regs-serial.h>
-
 #include <plat/clock.h>
 #include <plat/devs.h>
 #include <plat/cpu.h>
diff --git a/arch/arm/mach-s3c64xx/mach-smdk6410.c b/arch/arm/mach-s3c64xx/mach-smdk6410.c
index 43261d2..c6a8b2a 100644
--- a/arch/arm/mach-s3c64xx/mach-smdk6410.c
+++ b/arch/arm/mach-s3c64xx/mach-smdk6410.c
@@ -19,6 +19,7 @@
 #include <linux/init.h>
 #include <linux/input.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 #include <linux/platform_device.h>
 #include <linux/io.h>
 #include <linux/i2c.h>
@@ -55,7 +56,6 @@
 #include <asm/irq.h>
 #include <asm/mach-types.h>
 
-#include <plat/regs-serial.h>
 #include <mach/regs-gpio.h>
 #include <mach/gpio-samsung.h>
 #include <linux/platform_data/ata-samsung_cf.h>
diff --git a/arch/arm/mach-s3c64xx/s3c6400.c b/arch/arm/mach-s3c64xx/s3c6400.c
index 3db0c98..8c42807 100644
--- a/arch/arm/mach-s3c64xx/s3c6400.c
+++ b/arch/arm/mach-s3c64xx/s3c6400.c
@@ -23,6 +23,7 @@
 #include <linux/io.h>
 #include <linux/device.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 #include <linux/platform_device.h>
 #include <linux/of.h>
 
@@ -34,7 +35,6 @@
 #include <asm/irq.h>
 
 #include <plat/cpu-freq.h>
-#include <plat/regs-serial.h>
 #include <mach/regs-clock.h>
 
 #include <plat/cpu.h>
diff --git a/arch/arm/mach-s3c64xx/s3c6410.c b/arch/arm/mach-s3c64xx/s3c6410.c
index 72b2278..5be3f09 100644
--- a/arch/arm/mach-s3c64xx/s3c6410.c
+++ b/arch/arm/mach-s3c64xx/s3c6410.c
@@ -24,6 +24,7 @@
 #include <linux/io.h>
 #include <linux/device.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 #include <linux/platform_device.h>
 #include <linux/of.h>
 
@@ -35,7 +36,6 @@
 #include <asm/irq.h>
 
 #include <plat/cpu-freq.h>
-#include <plat/regs-serial.h>
 #include <mach/regs-clock.h>
 
 #include <plat/cpu.h>
diff --git a/arch/arm/mach-s5p64x0/common.c b/arch/arm/mach-s5p64x0/common.c
index 42e14f2..eb2ad14 100644
--- a/arch/arm/mach-s5p64x0/common.c
+++ b/arch/arm/mach-s5p64x0/common.c
@@ -19,6 +19,7 @@
 #include <linux/io.h>
 #include <linux/device.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 #include <clocksource/samsung_pwm.h>
 #include <linux/platform_device.h>
 #include <linux/sched.h>
@@ -50,7 +51,6 @@
 #include <plat/gpio-cfg.h>
 #include <plat/pwm-core.h>
 #include <plat/regs-irqtype.h>
-#include <plat/regs-serial.h>
 #include <plat/watchdog-reset.h>
 
 #include "common.h"
diff --git a/arch/arm/mach-s5p64x0/include/mach/debug-macro.S b/arch/arm/mach-s5p64x0/include/mach/debug-macro.S
index 5e2916f..8759e78 100644
--- a/arch/arm/mach-s5p64x0/include/mach/debug-macro.S
+++ b/arch/arm/mach-s5p64x0/include/mach/debug-macro.S
@@ -10,11 +10,10 @@
 
 /* pull in the relevant register and map files. */
 
+#include <linux/serial_s3c.h>
 #include <plat/map-base.h>
 #include <plat/map-s5p.h>
 
-#include <plat/regs-serial.h>
-
 	.macro addruart, rp, rv, tmp
 		mov	\rp, #0xE0000000
 		orr	\rp, \rp, #0x00100000
diff --git a/arch/arm/mach-s5p64x0/include/mach/timex.h b/arch/arm/mach-s5p64x0/include/mach/timex.h
deleted file mode 100644
index 4b91faa..0000000
--- a/arch/arm/mach-s5p64x0/include/mach/timex.h
+++ /dev/null
@@ -1,27 +0,0 @@
-/* linux/arch/arm/mach-s5p64x0/include/mach/timex.h
- *
- * Copyright (c) 2010 Samsung Electronics Co., Ltd.
- *		http://www.samsung.com
- *
- * Copyright (c) 2003-2005 Simtec Electronics
- *	Ben Dooks <ben@simtec.co.uk>
- *
- * S5P64X0 - time parameters
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#ifndef __ASM_ARCH_TIMEX_H
-#define __ASM_ARCH_TIMEX_H
-
-/* CLOCK_TICK_RATE needs to be evaluatable by the cpp, so making it
- * a variable is useless. It seems as long as we make our timers an
- * exact multiple of HZ, any value that makes a 1->1 correspondence
- * for the time conversion functions to/from jiffies is acceptable.
-*/
-
-#define CLOCK_TICK_RATE 12000000
-
-#endif /* __ASM_ARCH_TIMEX_H */
diff --git a/arch/arm/mach-s5p64x0/irq-pm.c b/arch/arm/mach-s5p64x0/irq-pm.c
index 3e6f245..1c83d28 100644
--- a/arch/arm/mach-s5p64x0/irq-pm.c
+++ b/arch/arm/mach-s5p64x0/irq-pm.c
@@ -14,9 +14,9 @@
 
 #include <linux/syscore_ops.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 #include <linux/io.h>
 
-#include <plat/regs-serial.h>
 #include <plat/pm.h>
 
 #include <mach/regs-gpio.h>
diff --git a/arch/arm/mach-s5p64x0/mach-smdk6440.c b/arch/arm/mach-s5p64x0/mach-smdk6440.c
index 9efdcc0..6840e19 100644
--- a/arch/arm/mach-s5p64x0/mach-smdk6440.c
+++ b/arch/arm/mach-s5p64x0/mach-smdk6440.c
@@ -17,6 +17,7 @@
 #include <linux/init.h>
 #include <linux/i2c.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 #include <linux/platform_device.h>
 #include <linux/io.h>
 #include <linux/module.h>
@@ -39,7 +40,6 @@
 #include <mach/regs-clock.h>
 #include <mach/regs-gpio.h>
 
-#include <plat/regs-serial.h>
 #include <plat/gpio-cfg.h>
 #include <plat/clock.h>
 #include <plat/devs.h>
diff --git a/arch/arm/mach-s5p64x0/mach-smdk6450.c b/arch/arm/mach-s5p64x0/mach-smdk6450.c
index c3cacc0..fa1341c 100644
--- a/arch/arm/mach-s5p64x0/mach-smdk6450.c
+++ b/arch/arm/mach-s5p64x0/mach-smdk6450.c
@@ -17,6 +17,7 @@
 #include <linux/init.h>
 #include <linux/i2c.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 #include <linux/platform_device.h>
 #include <linux/io.h>
 #include <linux/module.h>
@@ -39,7 +40,6 @@
 #include <mach/regs-clock.h>
 #include <mach/regs-gpio.h>
 
-#include <plat/regs-serial.h>
 #include <plat/gpio-cfg.h>
 #include <plat/clock.h>
 #include <plat/devs.h>
diff --git a/arch/arm/mach-s5pc100/common.c b/arch/arm/mach-s5pc100/common.c
index c5a8eea..6a41bf7 100644
--- a/arch/arm/mach-s5pc100/common.c
+++ b/arch/arm/mach-s5pc100/common.c
@@ -22,6 +22,7 @@
 #include <linux/io.h>
 #include <linux/device.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 #include <clocksource/samsung_pwm.h>
 #include <linux/platform_device.h>
 #include <linux/sched.h>
@@ -49,7 +50,6 @@
 #include <plat/onenand-core.h>
 #include <plat/pwm-core.h>
 #include <plat/spi-core.h>
-#include <plat/regs-serial.h>
 #include <plat/watchdog-reset.h>
 
 #include "common.h"
diff --git a/arch/arm/mach-s5pc100/include/mach/debug-macro.S b/arch/arm/mach-s5pc100/include/mach/debug-macro.S
index 66cb7f1..22c2385 100644
--- a/arch/arm/mach-s5pc100/include/mach/debug-macro.S
+++ b/arch/arm/mach-s5pc100/include/mach/debug-macro.S
@@ -13,8 +13,8 @@
 
 /* pull in the relevant register and map files. */
 
+#include <linux/serial_s3c.h>
 #include <mach/map.h>
-#include <plat/regs-serial.h>
 
 	/* note, for the boot process to work we have to keep the UART
 	 * virtual address aligned to an 1MiB boundary for the L1
diff --git a/arch/arm/mach-s5pc100/include/mach/tick.h b/arch/arm/mach-s5pc100/include/mach/tick.h
deleted file mode 100644
index 0af8e41..0000000
--- a/arch/arm/mach-s5pc100/include/mach/tick.h
+++ /dev/null
@@ -1,31 +0,0 @@
-/* linux/arch/arm/mach-s5pc100/include/mach/tick.h
- *
- * Copyright 2009 Samsung Electronics Co.
- *	Byungho Min <bhmin@samsung.com>
- *
- * S3C64XX - Timer tick support definitions
- *
- * Based on mach-s3c6400/include/mach/tick.h
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#ifndef __ASM_ARCH_TICK_H
-#define __ASM_ARCH_TICK_H __FILE__
-
-#include <linux/irqchip/arm-vic.h>
-
-/* note, the timer interrutps turn up in 2 places, the vic and then
- * the timer block. We take the VIC as the base at the moment.
- */
-static inline u32 s3c24xx_ostimer_pending(void)
-{
-	u32 pend = __raw_readl(VA_VIC0 + VIC_RAW_STATUS);
-	return pend & (1 << (IRQ_TIMER4_VIC - S5P_IRQ_VIC0(0)));
-}
-
-#define TICK_MAX	(0xffffffff)
-
-#endif /* __ASM_ARCH_TICK_H */
diff --git a/arch/arm/mach-s5pc100/include/mach/timex.h b/arch/arm/mach-s5pc100/include/mach/timex.h
deleted file mode 100644
index 47ffb17..0000000
--- a/arch/arm/mach-s5pc100/include/mach/timex.h
+++ /dev/null
@@ -1,24 +0,0 @@
-/* arch/arm/mach-s5pc100/include/mach/timex.h
- *
- * Copyright (c) 2003-2005 Simtec Electronics
- *	Ben Dooks <ben@simtec.co.uk>
- *
- * S3C6400 - time parameters
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#ifndef __ASM_ARCH_TIMEX_H
-#define __ASM_ARCH_TIMEX_H
-
-/* CLOCK_TICK_RATE needs to be evaluatable by the cpp, so making it
- * a variable is useless. It seems as long as we make our timers an
- * exact multiple of HZ, any value that makes a 1->1 correspondence
- * for the time conversion functions to/from jiffies is acceptable.
-*/
-
-#define CLOCK_TICK_RATE 12000000
-
-#endif /* __ASM_ARCH_TIMEX_H */
diff --git a/arch/arm/mach-s5pc100/mach-smdkc100.c b/arch/arm/mach-s5pc100/mach-smdkc100.c
index 9e256b9..668af3a 100644
--- a/arch/arm/mach-s5pc100/mach-smdkc100.c
+++ b/arch/arm/mach-s5pc100/mach-smdkc100.c
@@ -16,6 +16,7 @@
 #include <linux/timer.h>
 #include <linux/init.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 #include <linux/platform_device.h>
 #include <linux/io.h>
 #include <linux/gpio.h>
@@ -37,7 +38,6 @@
 #include <asm/irq.h>
 #include <asm/mach-types.h>
 
-#include <plat/regs-serial.h>
 #include <plat/gpio-cfg.h>
 
 #include <plat/clock.h>
diff --git a/arch/arm/mach-s5pv210/common.c b/arch/arm/mach-s5pv210/common.c
index 26027a2..7024dcd 100644
--- a/arch/arm/mach-s5pv210/common.c
+++ b/arch/arm/mach-s5pv210/common.c
@@ -24,6 +24,7 @@
 #include <linux/sched.h>
 #include <linux/dma-mapping.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 
 #include <asm/proc-fns.h>
 #include <asm/mach/arch.h>
@@ -46,7 +47,6 @@
 #include <plat/pwm-core.h>
 #include <plat/tv-core.h>
 #include <plat/spi-core.h>
-#include <plat/regs-serial.h>
 
 #include "common.h"
 
diff --git a/arch/arm/mach-s5pv210/include/mach/debug-macro.S b/arch/arm/mach-s5pv210/include/mach/debug-macro.S
index 80c2199..30b511a 100644
--- a/arch/arm/mach-s5pv210/include/mach/debug-macro.S
+++ b/arch/arm/mach-s5pv210/include/mach/debug-macro.S
@@ -12,8 +12,8 @@
 
 /* pull in the relevant register and map files. */
 
+#include <linux/serial_s3c.h>
 #include <mach/map.h>
-#include <plat/regs-serial.h>
 
 	/* note, for the boot process to work we have to keep the UART
 	 * virtual address aligned to an 1MiB boundary for the L1
diff --git a/arch/arm/mach-s5pv210/include/mach/timex.h b/arch/arm/mach-s5pv210/include/mach/timex.h
deleted file mode 100644
index 73dc854..0000000
--- a/arch/arm/mach-s5pv210/include/mach/timex.h
+++ /dev/null
@@ -1,29 +0,0 @@
-/* linux/arch/arm/mach-s5pv210/include/mach/timex.h
- *
- * Copyright (c) 2003-2010 Simtec Electronics
- *	Ben Dooks <ben@simtec.co.uk>
- *
- * Copyright (c) 2010 Samsung Electronics Co., Ltd.
- *		http://www.samsung.com/
- *
- * Based on arch/arm/mach-s5p6442/include/mach/timex.h
- *
- * S5PV210 - time parameters
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#ifndef __ASM_ARCH_TIMEX_H
-#define __ASM_ARCH_TIMEX_H __FILE__
-
-/* CLOCK_TICK_RATE needs to be evaluatable by the cpp, so making it
- * a variable is useless. It seems as long as we make our timers an
- * exact multiple of HZ, any value that makes a 1->1 correspondence
- * for the time conversion functions to/from jiffies is acceptable.
-*/
-
-#define CLOCK_TICK_RATE 12000000
-
-#endif /* __ASM_ARCH_TIMEX_H */
diff --git a/arch/arm/mach-s5pv210/mach-aquila.c b/arch/arm/mach-s5pv210/mach-aquila.c
index ad40ab0..cc37eda 100644
--- a/arch/arm/mach-s5pv210/mach-aquila.c
+++ b/arch/arm/mach-s5pv210/mach-aquila.c
@@ -12,6 +12,7 @@
 #include <linux/types.h>
 #include <linux/init.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 #include <linux/fb.h>
 #include <linux/i2c.h>
 #include <linux/i2c-gpio.h>
@@ -32,7 +33,6 @@
 #include <mach/regs-clock.h>
 
 #include <plat/gpio-cfg.h>
-#include <plat/regs-serial.h>
 #include <plat/devs.h>
 #include <plat/cpu.h>
 #include <plat/fb.h>
diff --git a/arch/arm/mach-s5pv210/mach-goni.c b/arch/arm/mach-s5pv210/mach-goni.c
index e5cd9fb..b41a38a 100644
--- a/arch/arm/mach-s5pv210/mach-goni.c
+++ b/arch/arm/mach-s5pv210/mach-goni.c
@@ -12,6 +12,7 @@
 #include <linux/types.h>
 #include <linux/init.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 #include <linux/fb.h>
 #include <linux/i2c.h>
 #include <linux/i2c-gpio.h>
@@ -39,7 +40,6 @@
 #include <mach/regs-clock.h>
 
 #include <plat/gpio-cfg.h>
-#include <plat/regs-serial.h>
 #include <plat/devs.h>
 #include <plat/cpu.h>
 #include <plat/fb.h>
diff --git a/arch/arm/mach-s5pv210/mach-smdkc110.c b/arch/arm/mach-s5pv210/mach-smdkc110.c
index 7c0ed07..448e1d2 100644
--- a/arch/arm/mach-s5pv210/mach-smdkc110.c
+++ b/arch/arm/mach-s5pv210/mach-smdkc110.c
@@ -12,6 +12,7 @@
 #include <linux/types.h>
 #include <linux/init.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 #include <linux/i2c.h>
 #include <linux/device.h>
 
@@ -23,7 +24,6 @@
 #include <mach/map.h>
 #include <mach/regs-clock.h>
 
-#include <plat/regs-serial.h>
 #include <plat/devs.h>
 #include <plat/cpu.h>
 #include <linux/platform_data/ata-samsung_cf.h>
diff --git a/arch/arm/mach-s5pv210/mach-smdkv210.c b/arch/arm/mach-s5pv210/mach-smdkv210.c
index f52cc15..2a6655f 100644
--- a/arch/arm/mach-s5pv210/mach-smdkv210.c
+++ b/arch/arm/mach-s5pv210/mach-smdkv210.c
@@ -13,6 +13,7 @@
 #include <linux/i2c.h>
 #include <linux/init.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 #include <linux/device.h>
 #include <linux/dm9000.h>
 #include <linux/fb.h>
@@ -32,7 +33,6 @@
 #include <mach/map.h>
 #include <mach/regs-clock.h>
 
-#include <plat/regs-serial.h>
 #include <plat/regs-srom.h>
 #include <plat/gpio-cfg.h>
 #include <plat/devs.h>
diff --git a/arch/arm/mach-s5pv210/mach-torbreck.c b/arch/arm/mach-s5pv210/mach-torbreck.c
index 579afe8..1578055 100644
--- a/arch/arm/mach-s5pv210/mach-torbreck.c
+++ b/arch/arm/mach-s5pv210/mach-torbreck.c
@@ -13,6 +13,7 @@
 #include <linux/i2c.h>
 #include <linux/init.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
@@ -22,7 +23,6 @@
 #include <mach/map.h>
 #include <mach/regs-clock.h>
 
-#include <plat/regs-serial.h>
 #include <plat/devs.h>
 #include <plat/cpu.h>
 #include <linux/platform_data/i2c-s3c2410.h>
diff --git a/arch/arm/mach-sa1100/include/mach/timex.h b/arch/arm/mach-sa1100/include/mach/timex.h
deleted file mode 100644
index 7a5d017..0000000
--- a/arch/arm/mach-sa1100/include/mach/timex.h
+++ /dev/null
@@ -1,12 +0,0 @@
-/*
- * arch/arm/mach-sa1100/include/mach/timex.h
- *
- * SA1100 architecture timex specifications
- *
- * Copyright (C) 1998 
- */
-
-/*
- * SA1100 timer
- */
-#define CLOCK_TICK_RATE		3686400
diff --git a/arch/arm/mach-sa1100/time.c b/arch/arm/mach-sa1100/time.c
index 6fd4acb..7aaac00 100644
--- a/arch/arm/mach-sa1100/time.c
+++ b/arch/arm/mach-sa1100/time.c
@@ -9,6 +9,7 @@
  *
  */
 #include <linux/init.h>
+#include <linux/kernel.h>
 #include <linux/errno.h>
 #include <linux/interrupt.h>
 #include <linux/irq.h>
@@ -20,6 +21,9 @@
 #include <mach/hardware.h>
 #include <mach/irqs.h>
 
+#define SA1100_CLOCK_FREQ 3686400
+#define SA1100_LATCH DIV_ROUND_CLOSEST(SA1100_CLOCK_FREQ, HZ)
+
 static u64 notrace sa1100_read_sched_clock(void)
 {
 	return readl_relaxed(OSCR);
@@ -93,7 +97,7 @@
 	/*
 	 * OSMR0 is the system timer: make sure OSCR is sufficiently behind
 	 */
-	writel_relaxed(OSMR0 - LATCH, OSCR);
+	writel_relaxed(OSMR0 - SA1100_LATCH, OSCR);
 }
 #else
 #define sa1100_timer_suspend NULL
@@ -128,7 +132,7 @@
 
 	setup_irq(IRQ_OST0, &sa1100_timer_irq);
 
-	clocksource_mmio_init(OSCR, "oscr", CLOCK_TICK_RATE, 200, 32,
+	clocksource_mmio_init(OSCR, "oscr", SA1100_CLOCK_FREQ, 200, 32,
 		clocksource_mmio_readl_up);
 	clockevents_config_and_register(&ckevt_sa1100_osmr0, 3686400,
 					MIN_OSCR_DELTA * 2, 0x7fffffff);
diff --git a/arch/arm/mach-shmobile/Kconfig b/arch/arm/mach-shmobile/Kconfig
index 05fa505..8a685ed 100644
--- a/arch/arm/mach-shmobile/Kconfig
+++ b/arch/arm/mach-shmobile/Kconfig
@@ -5,18 +5,13 @@
 	bool "Renesas ARM SoCs" if ARCH_MULTI_V7
 	depends on MMU
 	select ARCH_SHMOBILE
-	select CPU_V7
-	select GENERIC_CLOCKEVENTS
 	select HAVE_ARM_SCU if SMP
 	select HAVE_ARM_TWD if SMP
-	select HAVE_SMP
 	select ARM_GIC
-	select MIGHT_HAVE_CACHE_L2X0
 	select MIGHT_HAVE_PCI
 	select NO_IOPORT
 	select PINCTRL
 	select ARCH_REQUIRE_GPIOLIB
-	select CLKDEV_LOOKUP
 
 if ARCH_SHMOBILE_MULTI
 
diff --git a/arch/arm/mach-shmobile/clock-r8a7779.c b/arch/arm/mach-shmobile/clock-r8a7779.c
index f1fb89b..cabedeb 100644
--- a/arch/arm/mach-shmobile/clock-r8a7779.c
+++ b/arch/arm/mach-shmobile/clock-r8a7779.c
@@ -47,17 +47,10 @@
 
 #define MD(nr)	BIT(nr)
 
-#define FRQMR		IOMEM(0xffc80014)
 #define MSTPCR0		IOMEM(0xffc80030)
 #define MSTPCR1		IOMEM(0xffc80034)
 #define MSTPCR3		IOMEM(0xffc8003c)
 #define MSTPSR1		IOMEM(0xffc80044)
-#define MSTPSR4		IOMEM(0xffc80048)
-#define MSTPSR6		IOMEM(0xffc8004c)
-#define MSTPCR4		IOMEM(0xffc80050)
-#define MSTPCR5		IOMEM(0xffc80054)
-#define MSTPCR6		IOMEM(0xffc80058)
-#define MSTPCR7		IOMEM(0xffc80040)
 
 #define MODEMR		0xffcc0020
 
diff --git a/arch/arm/mach-shmobile/include/mach/common.h b/arch/arm/mach-shmobile/include/mach/common.h
index e319805..cb8e32d 100644
--- a/arch/arm/mach-shmobile/include/mach/common.h
+++ b/arch/arm/mach-shmobile/include/mach/common.h
@@ -25,7 +25,6 @@
 					    struct task_struct *idle);
 extern void shmobile_smp_apmu_cpu_die(unsigned int cpu);
 extern int shmobile_smp_apmu_cpu_kill(unsigned int cpu);
-extern void shmobile_invalidate_start(void);
 struct clk;
 extern int shmobile_clk_init(void);
 extern void shmobile_handle_irq_intc(struct pt_regs *);
diff --git a/arch/arm/mach-shmobile/include/mach/timex.h b/arch/arm/mach-shmobile/include/mach/timex.h
deleted file mode 100644
index ae0d8d8..0000000
--- a/arch/arm/mach-shmobile/include/mach/timex.h
+++ /dev/null
@@ -1,6 +0,0 @@
-#ifndef __ASM_MACH_TIMEX_H
-#define __ASM_MACH_TIMEX_H
-
-#define CLOCK_TICK_RATE		1193180 /* unused i8253 PIT value */
-
-#endif /* __ASM_MACH_TIMEX_H */
diff --git a/arch/arm/mach-shmobile/setup-emev2.c b/arch/arm/mach-shmobile/setup-emev2.c
index c8f2a1a..c71d667 100644
--- a/arch/arm/mach-shmobile/setup-emev2.c
+++ b/arch/arm/mach-shmobile/setup-emev2.c
@@ -58,7 +58,7 @@
 	of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
 }
 
-static const char *emev2_boards_compat_dt[] __initdata = {
+static const char *emev2_boards_compat_dt[] __initconst = {
 	"renesas,emev2",
 	NULL,
 };
diff --git a/arch/arm/mach-socfpga/Kconfig b/arch/arm/mach-socfpga/Kconfig
index aee77f0..b5f8d75 100644
--- a/arch/arm/mach-socfpga/Kconfig
+++ b/arch/arm/mach-socfpga/Kconfig
@@ -1,17 +1,10 @@
 config ARCH_SOCFPGA
 	bool "Altera SOCFPGA family" if ARCH_MULTI_V7
-	select ARCH_WANT_OPTIONAL_GPIOLIB
 	select ARM_AMBA
 	select ARM_GIC
 	select CACHE_L2X0
-	select COMMON_CLK
-	select CPU_V7
 	select DW_APB_TIMER_OF
-	select GENERIC_CLOCKEVENTS
 	select GPIO_PL061 if GPIOLIB
 	select HAVE_ARM_SCU
 	select HAVE_ARM_TWD if SMP
-	select HAVE_SMP
 	select MFD_SYSCON
-	select SPARSE_IRQ
-	select USE_OF
diff --git a/arch/arm/mach-spear/Kconfig b/arch/arm/mach-spear/Kconfig
index ac1710e6..5c57262 100644
--- a/arch/arm/mach-spear/Kconfig
+++ b/arch/arm/mach-spear/Kconfig
@@ -8,8 +8,6 @@
 	select ARCH_REQUIRE_GPIOLIB
 	select ARM_AMBA
 	select CLKSRC_MMIO
-	select COMMON_CLK
-	select GENERIC_CLOCKEVENTS
 
 if PLAT_SPEAR
 
@@ -18,14 +16,10 @@
 	depends on ARCH_MULTI_V7 || PLAT_SPEAR_SINGLE
 	select ARCH_HAS_CPUFREQ
 	select ARM_GIC
-	select CPU_V7
 	select GPIO_SPEAR_SPICS
 	select HAVE_ARM_SCU if SMP
 	select HAVE_ARM_TWD if SMP
-	select HAVE_SMP
-	select MIGHT_HAVE_CACHE_L2X0
 	select PINCTRL
-	select USE_OF
 	help
 	  Supports for ARM's SPEAR13XX family
 
@@ -50,9 +44,7 @@
 	depends on ARCH_MULTI_V5 || PLAT_SPEAR_SINGLE
 	depends on !ARCH_SPEAR13XX
 	select ARM_VIC
-	select CPU_ARM926T
 	select PINCTRL
-	select USE_OF
 	help
 	  Supports for ARM's SPEAR3XX family
 
@@ -83,14 +75,12 @@
 	depends on ARCH_MULTI_V5 || PLAT_SPEAR_SINGLE
 	depends on !ARCH_SPEAR13XX
 	select ARM_VIC
-	select CPU_ARM926T
 	help
 	  Supports for ARM's SPEAR6XX family
 
 config MACH_SPEAR600
 	def_bool y
 	depends on ARCH_SPEAR6XX
-	select USE_OF
 	help
 	  Supports ST SPEAr600 boards configured via the device-treesource "arch/arm/mach-spear6xx/Kconfig"
 
diff --git a/arch/arm/mach-spear/include/mach/timex.h b/arch/arm/mach-spear/include/mach/timex.h
deleted file mode 100644
index ef95e5b..0000000
--- a/arch/arm/mach-spear/include/mach/timex.h
+++ /dev/null
@@ -1,19 +0,0 @@
-/*
- * arch/arm/plat-spear/include/plat/timex.h
- *
- * SPEAr platform specific timex definitions
- *
- * Copyright (C) 2009 ST Microelectronics
- * Viresh Kumar <viresh.linux@gmail.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#ifndef __PLAT_TIMEX_H
-#define __PLAT_TIMEX_H
-
-#define CLOCK_TICK_RATE			48000000
-
-#endif /* __PLAT_TIMEX_H */
diff --git a/arch/arm/mach-sti/Kconfig b/arch/arm/mach-sti/Kconfig
index d71654b..d2c13ba 100644
--- a/arch/arm/mach-sti/Kconfig
+++ b/arch/arm/mach-sti/Kconfig
@@ -1,14 +1,10 @@
 menuconfig ARCH_STI
 	bool "STMicroelectronics Consumer Electronics SOCs with Device Trees" if ARCH_MULTI_V7
-	select GENERIC_CLOCKEVENTS
-	select CLKDEV_LOOKUP
 	select ARM_GIC
 	select ARM_GLOBAL_TIMER
 	select PINCTRL
 	select PINCTRL_ST
 	select MFD_SYSCON
-	select MIGHT_HAVE_CACHE_L2X0
-	select HAVE_SMP
 	select HAVE_ARM_SCU if SMP
 	select ARCH_REQUIRE_GPIOLIB
 	select ARM_ERRATA_754322
diff --git a/arch/arm/mach-sunxi/Kconfig b/arch/arm/mach-sunxi/Kconfig
index b9d6cad..9de27cf 100644
--- a/arch/arm/mach-sunxi/Kconfig
+++ b/arch/arm/mach-sunxi/Kconfig
@@ -5,14 +5,9 @@
 	select ARM_GIC
 	select ARM_PSCI
 	select CLKSRC_MMIO
-	select CLKSRC_OF
-	select COMMON_CLK
-	select GENERIC_CLOCKEVENTS
 	select GENERIC_IRQ_CHIP
-	select HAVE_SMP
 	select PINCTRL
 	select PINCTRL_SUNXI
 	select RESET_CONTROLLER
-	select SPARSE_IRQ
 	select SUN4I_TIMER
 	select SUN5I_HSTIMER
diff --git a/arch/arm/mach-tegra/Kconfig b/arch/arm/mach-tegra/Kconfig
index b1232d8..f61cd5b 100644
--- a/arch/arm/mach-tegra/Kconfig
+++ b/arch/arm/mach-tegra/Kconfig
@@ -5,24 +5,16 @@
 	select ARCH_SUPPORTS_TRUSTED_FOUNDATIONS
 	select ARM_GIC
 	select CLKSRC_MMIO
-	select CLKSRC_OF
-	select COMMON_CLK
-	select CPU_V7
-	select GENERIC_CLOCKEVENTS
 	select HAVE_ARM_SCU if SMP
 	select HAVE_ARM_TWD if SMP
-	select HAVE_SMP
-	select MIGHT_HAVE_CACHE_L2X0
 	select MIGHT_HAVE_PCI
 	select PINCTRL
 	select ARCH_HAS_RESET_CONTROLLER
 	select RESET_CONTROLLER
 	select SOC_BUS
-	select SPARSE_IRQ
 	select USB_ARCH_HAS_EHCI if USB_SUPPORT
 	select USB_ULPI if USB_PHY
 	select USB_ULPI_VIEWPORT if USB_PHY
-	select USE_OF
 	help
 	  This enables support for NVIDIA Tegra based systems.
 
diff --git a/arch/arm/mach-u300/Kconfig b/arch/arm/mach-u300/Kconfig
index 8e23071..e3a96d7 100644
--- a/arch/arm/mach-u300/Kconfig
+++ b/arch/arm/mach-u300/Kconfig
@@ -3,20 +3,14 @@
 	depends on MMU
 	select ARCH_REQUIRE_GPIOLIB
 	select ARM_AMBA
-	select ARM_PATCH_PHYS_VIRT
 	select ARM_VIC
 	select CLKSRC_MMIO
-	select CLKSRC_OF
-	select COMMON_CLK
 	select CPU_ARM926T
-	select GENERIC_CLOCKEVENTS
 	select HAVE_TCM
 	select PINCTRL
 	select PINCTRL_COH901
 	select PINCTRL_U300
-	select SPARSE_IRQ
 	select MFD_SYSCON
-	select USE_OF
 	help
 	  Support for ST-Ericsson U300 series mobile platforms.
 
diff --git a/arch/arm/mach-ux500/Kconfig b/arch/arm/mach-ux500/Kconfig
index 0034d2c..8052bd5 100644
--- a/arch/arm/mach-ux500/Kconfig
+++ b/arch/arm/mach-ux500/Kconfig
@@ -11,13 +11,8 @@
 	select ARM_GIC
 	select CACHE_L2X0
 	select CLKSRC_NOMADIK_MTU
-	select COMMON_CLK
-	select CPU_V7
-	select GENERIC_CLOCKEVENTS
 	select HAVE_ARM_SCU if SMP
 	select HAVE_ARM_TWD if SMP
-	select HAVE_SMP
-	select MIGHT_HAVE_CACHE_L2X0
 	select PINCTRL
 	select PINCTRL_ABX500
 	select PINCTRL_NOMADIK
@@ -76,7 +71,6 @@
 config MACH_UX500_DT
 	bool "Generic U8500 support using device tree"
 	depends on MACH_MOP500
-	select USE_OF
 
 endmenu
 
diff --git a/arch/arm/mach-versatile/include/mach/timex.h b/arch/arm/mach-versatile/include/mach/timex.h
deleted file mode 100644
index 426199b..0000000
--- a/arch/arm/mach-versatile/include/mach/timex.h
+++ /dev/null
@@ -1,23 +0,0 @@
-/*
- *  arch/arm/mach-versatile/include/mach/timex.h
- *
- *  Versatile architecture timex specifications
- *
- *  Copyright (C) 2003 ARM Limited
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-
-#define CLOCK_TICK_RATE		(50000000 / 16)
diff --git a/arch/arm/mach-vexpress/Kconfig b/arch/arm/mach-vexpress/Kconfig
index 4a70be4..80b4be3 100644
--- a/arch/arm/mach-vexpress/Kconfig
+++ b/arch/arm/mach-vexpress/Kconfig
@@ -5,16 +5,11 @@
 	select ARM_AMBA
 	select ARM_GIC
 	select ARM_TIMER_SP804
-	select COMMON_CLK
 	select COMMON_CLK_VERSATILE
-	select CPU_V7
-	select GENERIC_CLOCKEVENTS
 	select HAVE_ARM_SCU if SMP
 	select HAVE_ARM_TWD if SMP
 	select HAVE_PATA_PLATFORM
-	select HAVE_SMP
 	select ICST
-	select MIGHT_HAVE_CACHE_L2X0
 	select NO_IOPORT
 	select PLAT_VERSATILE
 	select PLAT_VERSATILE_CLCD
diff --git a/arch/arm/mach-virt/Kconfig b/arch/arm/mach-virt/Kconfig
deleted file mode 100644
index 081d469..0000000
--- a/arch/arm/mach-virt/Kconfig
+++ /dev/null
@@ -1,10 +0,0 @@
-config ARCH_VIRT
-	bool "Dummy Virtual Machine" if ARCH_MULTI_V7
-	select ARCH_WANT_OPTIONAL_GPIOLIB
-	select ARM_GIC
-	select HAVE_ARM_ARCH_TIMER
-	select ARM_PSCI
-	select HAVE_SMP
-	select CPU_V7
-	select SPARSE_IRQ
-	select USE_OF
diff --git a/arch/arm/mach-virt/Makefile b/arch/arm/mach-virt/Makefile
deleted file mode 100644
index 7ddbfa6..0000000
--- a/arch/arm/mach-virt/Makefile
+++ /dev/null
@@ -1,5 +0,0 @@
-#
-# Makefile for the linux kernel.
-#
-
-obj-y					:= virt.o
diff --git a/arch/arm/mach-virt/virt.c b/arch/arm/mach-virt/virt.c
deleted file mode 100644
index b184e57..0000000
--- a/arch/arm/mach-virt/virt.c
+++ /dev/null
@@ -1,41 +0,0 @@
-/*
- * Dummy Virtual Machine - does what it says on the tin.
- *
- * Copyright (C) 2012 ARM Ltd
- * Authors: Will Deacon <will.deacon@arm.com>,
- *          Marc Zyngier <marc.zyngier@arm.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <http://www.gnu.org/licenses/>.
- */
-
-#include <linux/of_irq.h>
-#include <linux/of_platform.h>
-#include <linux/smp.h>
-
-#include <asm/mach/arch.h>
-
-static void __init virt_init(void)
-{
-	of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
-}
-
-static const char *virt_dt_match[] = {
-	"linux,dummy-virt",
-	"xen,xenvm",
-	NULL
-};
-
-DT_MACHINE_START(VIRT, "Dummy Virtual Machine")
-	.init_machine	= virt_init,
-	.dt_compat	= virt_dt_match,
-MACHINE_END
diff --git a/arch/arm/mach-vt8500/Kconfig b/arch/arm/mach-vt8500/Kconfig
index 927be93..08f56a4 100644
--- a/arch/arm/mach-vt8500/Kconfig
+++ b/arch/arm/mach-vt8500/Kconfig
@@ -3,8 +3,6 @@
 	select ARCH_HAS_CPUFREQ
 	select ARCH_REQUIRE_GPIOLIB
 	select CLKDEV_LOOKUP
-	select CLKSRC_OF
-	select GENERIC_CLOCKEVENTS
 	select VT8500_TIMER
 	select PINCTRL
 	help
@@ -21,7 +19,6 @@
 	bool "WonderMedia WM8750"
 	depends on ARCH_MULTI_V6
 	select ARCH_VT8500
-	select CPU_V6
 	help
 	  Support for WonderMedia WM8750 System-on-Chip.
 
@@ -29,6 +26,5 @@
 	bool "WonderMedia WM8850"
 	depends on ARCH_MULTI_V7
 	select ARCH_VT8500
-	select CPU_V7
 	help
 	  Support for WonderMedia WM8850 System-on-Chip.
diff --git a/arch/arm/mach-w90x900/include/mach/timex.h b/arch/arm/mach-w90x900/include/mach/timex.h
deleted file mode 100644
index 164dce0..0000000
--- a/arch/arm/mach-w90x900/include/mach/timex.h
+++ /dev/null
@@ -1,25 +0,0 @@
-/*
- * arch/arm/mach-w90x900/include/mach/timex.h
- *
- * Copyright (c) 2008 Nuvoton technology corporation
- * All rights reserved.
- *
- * Wan ZongShun <mcuos.com@gmail.com>
- *
- * Based on arch/arm/mach-s3c2410/include/mach/timex.h
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- */
-
-#ifndef __ASM_ARCH_TIMEX_H
-#define __ASM_ARCH_TIMEX_H
-
-/* CLOCK_TICK_RATE Now, I don't use it. */
-
-#define CLOCK_TICK_RATE 15000000
-
-#endif /* __ASM_ARCH_TIMEX_H */
diff --git a/arch/arm/mach-zynq/Kconfig b/arch/arm/mach-zynq/Kconfig
index 6b04260..105d39b 100644
--- a/arch/arm/mach-zynq/Kconfig
+++ b/arch/arm/mach-zynq/Kconfig
@@ -2,16 +2,9 @@
 	bool "Xilinx Zynq ARM Cortex A9 Platform" if ARCH_MULTI_V7
 	select ARM_AMBA
 	select ARM_GIC
-	select COMMON_CLK
-	select CPU_V7
-	select GENERIC_CLOCKEVENTS
 	select HAVE_ARM_SCU if SMP
 	select HAVE_ARM_TWD if SMP
 	select ICST
-	select MIGHT_HAVE_CACHE_L2X0
-	select USE_OF
-	select HAVE_SMP
-	select SPARSE_IRQ
 	select CADENCE_TTC_TIMER
 	select ARM_GLOBAL_TIMER
 	help
diff --git a/arch/arm/plat-omap/include/plat/timex.h b/arch/arm/plat-omap/include/plat/timex.h
deleted file mode 100644
index e27d2da..0000000
--- a/arch/arm/plat-omap/include/plat/timex.h
+++ /dev/null
@@ -1,33 +0,0 @@
-/*
- * arch/arm/plat-omap/include/mach/timex.h
- *
- * Copyright (C) 2000 RidgeRun, Inc.
- * Author:  Greg Lonnon <glonnon@ridgerun.com>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the  GNU General Public License along
- * with this program; if not, write  to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#if !defined(__ASM_ARCH_OMAP_TIMEX_H)
-#define __ASM_ARCH_OMAP_TIMEX_H
-
-#define CLOCK_TICK_RATE		(HZ * 100000UL)
-
-#endif /* __ASM_ARCH_OMAP_TIMEX_H */
diff --git a/arch/arm/plat-samsung/clock.c b/arch/arm/plat-samsung/clock.c
index 47c9fad..ddfebdd 100644
--- a/arch/arm/plat-samsung/clock.c
+++ b/arch/arm/plat-samsung/clock.c
@@ -52,7 +52,7 @@
 #include <plat/cpu.h>
 
 #include <linux/serial_core.h>
-#include <plat/regs-serial.h> /* for s3c24xx_uart_devs */
+#include <linux/serial_s3c.h> /* for s3c24xx_uart_devs */
 
 /* clock information */
 
diff --git a/arch/arm/plat-samsung/cpu.c b/arch/arm/plat-samsung/cpu.c
index 46b426e..364963a 100644
--- a/arch/arm/plat-samsung/cpu.c
+++ b/arch/arm/plat-samsung/cpu.c
@@ -28,13 +28,6 @@
 }
 EXPORT_SYMBOL(samsung_rev);
 
-void __init s3c24xx_init_cpu(void)
-{
-	/* nothing here yet */
-
-	samsung_cpu_rev = 0;
-}
-
 void __init s3c64xx_init_cpu(void)
 {
 	samsung_cpu_id = __raw_readl(S3C_VA_SYS + 0x118);
diff --git a/arch/arm/plat-samsung/devs.c b/arch/arm/plat-samsung/devs.c
index ac07e87..c64a39a 100644
--- a/arch/arm/plat-samsung/devs.c
+++ b/arch/arm/plat-samsung/devs.c
@@ -18,6 +18,7 @@
 #include <linux/timer.h>
 #include <linux/init.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 #include <linux/platform_device.h>
 #include <linux/io.h>
 #include <linux/slab.h>
@@ -64,7 +65,6 @@
 #include <linux/platform_data/usb-s3c2410_udc.h>
 #include <linux/platform_data/usb-ohci-s3c2410.h>
 #include <plat/usb-phy.h>
-#include <plat/regs-serial.h>
 #include <plat/regs-spi.h>
 #include <linux/platform_data/spi-s3c64xx.h>
 
@@ -744,10 +744,7 @@
 	if (!pd) {
 		pd = &default_i2c_data;
 
-		if (soc_is_exynos4210() ||
-		    soc_is_exynos4212() || soc_is_exynos4412())
-			pd->bus_num = 8;
-		else if (soc_is_s5pv210())
+		if (soc_is_s5pv210())
 			pd->bus_num = 3;
 		else
 			pd->bus_num = 0;
@@ -764,10 +761,7 @@
 {
 	struct s5p_hdmi_platform_data *pd = &s5p_hdmi_def_platdata;
 
-	if (soc_is_exynos4210() ||
-	    soc_is_exynos4212() || soc_is_exynos4412())
-		pd->hdmiphy_bus = 8;
-	else if (soc_is_s5pv210())
+	if (soc_is_s5pv210())
 		pd->hdmiphy_bus = 3;
 	else
 		pd->hdmiphy_bus = 0;
diff --git a/arch/arm/plat-samsung/include/plat/cpu.h b/arch/arm/plat-samsung/include/plat/cpu.h
index 335beb3..31164b3 100644
--- a/arch/arm/plat-samsung/include/plat/cpu.h
+++ b/arch/arm/plat-samsung/include/plat/cpu.h
@@ -199,7 +199,6 @@
 
 extern void s3c24xx_init_io(struct map_desc *mach_desc, int size);
 
-extern void s3c24xx_init_cpu(void);
 extern void s3c64xx_init_cpu(void);
 extern void s5p_init_cpu(void __iomem *cpuid_addr);
 
diff --git a/arch/arm/plat-samsung/include/plat/regs-serial.h b/arch/arm/plat-samsung/include/plat/regs-serial.h
deleted file mode 100644
index f05f2af..0000000
--- a/arch/arm/plat-samsung/include/plat/regs-serial.h
+++ /dev/null
@@ -1 +0,0 @@
-#include <linux/serial_s3c.h>
diff --git a/arch/arm/plat-samsung/include/plat/uncompress.h b/arch/arm/plat-samsung/include/plat/uncompress.h
index f48dc0a..61054fd 100644
--- a/arch/arm/plat-samsung/include/plat/uncompress.h
+++ b/arch/arm/plat-samsung/include/plat/uncompress.h
@@ -29,7 +29,7 @@
 
 /* defines for UART registers */
 
-#include <plat/regs-serial.h>
+#include <linux/serial_s3c.h>
 
 /* working in physical space... */
 #define S3C_WDOGREG(x)	((S3C_PA_WDT + (x)))
diff --git a/arch/arm/plat-samsung/init.c b/arch/arm/plat-samsung/init.c
index aa9511b..0ffc84a 100644
--- a/arch/arm/plat-samsung/init.c
+++ b/arch/arm/plat-samsung/init.c
@@ -21,6 +21,7 @@
 #include <linux/interrupt.h>
 #include <linux/ioport.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 #include <linux/platform_device.h>
 #include <linux/of.h>
 
@@ -33,8 +34,6 @@
 #include <plat/devs.h>
 #include <plat/clock.h>
 
-#include <plat/regs-serial.h>
-
 static struct cpu_table *cpu;
 
 static struct cpu_table * __init s3c_lookup_cpu(unsigned long idcode,
diff --git a/arch/arm/plat-samsung/pm-gpio.c b/arch/arm/plat-samsung/pm-gpio.c
index dd4c15d0..da26881 100644
--- a/arch/arm/plat-samsung/pm-gpio.c
+++ b/arch/arm/plat-samsung/pm-gpio.c
@@ -196,8 +196,7 @@
 	.resume = samsung_gpio_pm_2bit_resume,
 };
 
-#if defined(CONFIG_ARCH_S3C64XX) || defined(CONFIG_PLAT_S5P) \
-	|| defined(CONFIG_ARCH_EXYNOS)
+#if defined(CONFIG_ARCH_S3C64XX) || defined(CONFIG_PLAT_S5P)
 static void samsung_gpio_pm_4bit_save(struct samsung_gpio_chip *chip)
 {
 	chip->pm_save[1] = __raw_readl(chip->base + OFFS_CON);
@@ -307,7 +306,7 @@
 	.save	= samsung_gpio_pm_4bit_save,
 	.resume = samsung_gpio_pm_4bit_resume,
 };
-#endif /* CONFIG_ARCH_S3C64XX || CONFIG_PLAT_S5P || CONFIG_ARCH_EXYNOS */
+#endif /* CONFIG_ARCH_S3C64XX || CONFIG_PLAT_S5P */
 
 /**
  * samsung_pm_save_gpio() - save gpio chip data for suspend
diff --git a/arch/arm/plat-samsung/pm.c b/arch/arm/plat-samsung/pm.c
index e5b0f2c..ae9baa2 100644
--- a/arch/arm/plat-samsung/pm.c
+++ b/arch/arm/plat-samsung/pm.c
@@ -18,13 +18,12 @@
 #include <linux/delay.h>
 #include <linux/of.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 #include <linux/io.h>
 
 #include <asm/cacheflush.h>
 #include <asm/suspend.h>
 
-#include <plat/regs-serial.h>
-
 #ifdef CONFIG_SAMSUNG_ATAGS
 #include <mach/hardware.h>
 #include <mach/map.h>
diff --git a/arch/arm/plat-samsung/s5p-irq-pm.c b/arch/arm/plat-samsung/s5p-irq-pm.c
index 5914980..52b1694 100644
--- a/arch/arm/plat-samsung/s5p-irq-pm.c
+++ b/arch/arm/plat-samsung/s5p-irq-pm.c
@@ -22,10 +22,7 @@
 #include <mach/map.h>
 
 #include <mach/regs-gpio.h>
-
-#ifndef CONFIG_ARCH_EXYNOS
 #include <mach/regs-irq.h>
-#endif
 
 /* state for IRQs over sleep */
 
@@ -43,18 +40,8 @@
 	unsigned long irqbit;
 	unsigned int irq_rtc_tic, irq_rtc_alarm;
 
-#ifdef CONFIG_ARCH_EXYNOS
-	if (soc_is_exynos5250()) {
-		irq_rtc_tic = EXYNOS5_IRQ_RTC_TIC;
-		irq_rtc_alarm = EXYNOS5_IRQ_RTC_ALARM;
-	} else {
-		irq_rtc_tic = EXYNOS4_IRQ_RTC_TIC;
-		irq_rtc_alarm = EXYNOS4_IRQ_RTC_ALARM;
-	}
-#else
 	irq_rtc_tic = IRQ_RTC_TIC;
 	irq_rtc_alarm = IRQ_RTC_ALARM;
-#endif
 
 	if (data->irq == irq_rtc_tic || data->irq == irq_rtc_alarm) {
 		irqbit = 1 << (data->irq + 1 - irq_rtc_alarm);
diff --git a/drivers/clocksource/Kconfig b/drivers/clocksource/Kconfig
index cd6950f..6510ec4 100644
--- a/drivers/clocksource/Kconfig
+++ b/drivers/clocksource/Kconfig
@@ -140,3 +140,6 @@
 	bool
 	help
 	  Support for Period Interrupt Timer on Freescale Vybrid Family SoCs.
+
+config CLKSRC_QCOM
+	bool
diff --git a/drivers/clocksource/Makefile b/drivers/clocksource/Makefile
index c7ca50a..2e0c0cc 100644
--- a/drivers/clocksource/Makefile
+++ b/drivers/clocksource/Makefile
@@ -32,6 +32,7 @@
 obj-$(CONFIG_CLKSRC_EXYNOS_MCT)	+= exynos_mct.o
 obj-$(CONFIG_CLKSRC_SAMSUNG_PWM)	+= samsung_pwm_timer.o
 obj-$(CONFIG_VF_PIT_TIMER)	+= vf_pit_timer.o
+obj-$(CONFIG_CLKSRC_QCOM)	+= qcom-timer.o
 
 obj-$(CONFIG_ARM_ARCH_TIMER)		+= arm_arch_timer.o
 obj-$(CONFIG_ARM_GLOBAL_TIMER)		+= arm_global_timer.o
diff --git a/drivers/clocksource/exynos_mct.c b/drivers/clocksource/exynos_mct.c
index 48f76bc..ed49b25 100644
--- a/drivers/clocksource/exynos_mct.c
+++ b/drivers/clocksource/exynos_mct.c
@@ -25,8 +25,6 @@
 #include <linux/of_address.h>
 #include <linux/clocksource.h>
 
-#include <asm/mach/time.h>
-
 #define EXYNOS4_MCTREG(x)		(x)
 #define EXYNOS4_MCT_G_CNT_L		EXYNOS4_MCTREG(0x100)
 #define EXYNOS4_MCT_G_CNT_U		EXYNOS4_MCTREG(0x104)
diff --git a/arch/arm/mach-msm/timer.c b/drivers/clocksource/qcom-timer.c
similarity index 97%
rename from arch/arm/mach-msm/timer.c
rename to drivers/clocksource/qcom-timer.c
index fd16449..e807acf 100644
--- a/arch/arm/mach-msm/timer.c
+++ b/drivers/clocksource/qcom-timer.c
@@ -1,7 +1,7 @@
 /*
  *
  * Copyright (C) 2007 Google, Inc.
- * Copyright (c) 2009-2012, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2009-2012,2014, The Linux Foundation. All rights reserved.
  *
  * This software is licensed under the terms of the GNU General Public
  * License version 2, as published by the Free Software Foundation, and
@@ -26,10 +26,6 @@
 #include <linux/of_irq.h>
 #include <linux/sched_clock.h>
 
-#include <asm/mach/time.h>
-
-#include "common.h"
-
 #define TIMER_MATCH_VAL			0x0000
 #define TIMER_COUNT_VAL			0x0004
 #define TIMER_ENABLE			0x0008
@@ -110,15 +106,6 @@
 	return readl_relaxed(source_base + TIMER_COUNT_VAL);
 }
 
-static notrace cycle_t msm_read_timer_count_shift(struct clocksource *cs)
-{
-	/*
-	 * Shift timer count down by a constant due to unreliable lower bits
-	 * on some targets.
-	 */
-	return msm_read_timer_count(cs) >> MSM_DGT_SHIFT;
-}
-
 static struct clocksource msm_clocksource = {
 	.name	= "dg_timer",
 	.rating	= 300,
@@ -232,7 +219,7 @@
 	sched_clock_register(msm_sched_clock_read, sched_bits, dgt_hz);
 }
 
-#ifdef CONFIG_OF
+#ifdef CONFIG_ARCH_QCOM
 static void __init msm_dt_timer_init(struct device_node *np)
 {
 	u32 freq;
@@ -285,7 +272,7 @@
 }
 CLOCKSOURCE_OF_DECLARE(kpss_timer, "qcom,kpss-timer", msm_dt_timer_init);
 CLOCKSOURCE_OF_DECLARE(scss_timer, "qcom,scss-timer", msm_dt_timer_init);
-#endif
+#else
 
 static int __init msm_timer_map(phys_addr_t addr, u32 event, u32 source,
 				u32 sts)
@@ -305,6 +292,15 @@
 	return 0;
 }
 
+static notrace cycle_t msm_read_timer_count_shift(struct clocksource *cs)
+{
+	/*
+	 * Shift timer count down by a constant due to unreliable lower bits
+	 * on some targets.
+	 */
+	return msm_read_timer_count(cs) >> MSM_DGT_SHIFT;
+}
+
 void __init msm7x01_timer_init(void)
 {
 	struct clocksource *cs = &msm_clocksource;
@@ -331,3 +327,4 @@
 		return;
 	msm_timer_init(19200000 / 4, 32, 7, false);
 }
+#endif
diff --git a/drivers/clocksource/timer-marco.c b/drivers/clocksource/timer-marco.c
index 09a17d9..b52e1c0 100644
--- a/drivers/clocksource/timer-marco.c
+++ b/drivers/clocksource/timer-marco.c
@@ -19,7 +19,8 @@
 #include <linux/of_irq.h>
 #include <linux/of_address.h>
 #include <linux/sched_clock.h>
-#include <asm/mach/time.h>
+
+#define MARCO_CLOCK_FREQ 1000000
 
 #define SIRFSOC_TIMER_32COUNTER_0_CTRL			0x0000
 #define SIRFSOC_TIMER_32COUNTER_1_CTRL			0x0004
@@ -191,7 +192,7 @@
 	ce->rating = 200;
 	ce->set_mode = sirfsoc_timer_set_mode;
 	ce->set_next_event = sirfsoc_timer_set_next_event;
-	clockevents_calc_mult_shift(ce, CLOCK_TICK_RATE, 60);
+	clockevents_calc_mult_shift(ce, MARCO_CLOCK_FREQ, 60);
 	ce->max_delta_ns = clockevent_delta2ns(-2, ce);
 	ce->min_delta_ns = clockevent_delta2ns(2, ce);
 	ce->cpumask = cpumask_of(cpu);
@@ -263,11 +264,11 @@
 	BUG_ON(IS_ERR(clk));
 	rate = clk_get_rate(clk);
 
-	BUG_ON(rate < CLOCK_TICK_RATE);
-	BUG_ON(rate % CLOCK_TICK_RATE);
+	BUG_ON(rate < MARCO_CLOCK_FREQ);
+	BUG_ON(rate % MARCO_CLOCK_FREQ);
 
 	/* Initialize the timer dividers */
-	timer_div = rate / CLOCK_TICK_RATE - 1;
+	timer_div = rate / MARCO_CLOCK_FREQ - 1;
 	writel_relaxed(timer_div << 16, sirfsoc_timer_base + SIRFSOC_TIMER_64COUNTER_CTRL);
 	writel_relaxed(timer_div << 16, sirfsoc_timer_base + SIRFSOC_TIMER_32COUNTER_0_CTRL);
 	writel_relaxed(timer_div << 16, sirfsoc_timer_base + SIRFSOC_TIMER_32COUNTER_1_CTRL);
@@ -283,7 +284,7 @@
 	/* Clear all interrupts */
 	writel_relaxed(0xFFFF, sirfsoc_timer_base + SIRFSOC_TIMER_INTR_STATUS);
 
-	BUG_ON(clocksource_register_hz(&sirfsoc_clocksource, CLOCK_TICK_RATE));
+	BUG_ON(clocksource_register_hz(&sirfsoc_clocksource, MARCO_CLOCK_FREQ));
 
 	sirfsoc_clockevent_init();
 }
diff --git a/drivers/clocksource/timer-prima2.c b/drivers/clocksource/timer-prima2.c
index 8a492d3..1a6b2d6 100644
--- a/drivers/clocksource/timer-prima2.c
+++ b/drivers/clocksource/timer-prima2.c
@@ -21,6 +21,8 @@
 #include <linux/sched_clock.h>
 #include <asm/mach/time.h>
 
+#define PRIMA2_CLOCK_FREQ 1000000
+
 #define SIRFSOC_TIMER_COUNTER_LO	0x0000
 #define SIRFSOC_TIMER_COUNTER_HI	0x0004
 #define SIRFSOC_TIMER_MATCH_0		0x0008
@@ -173,7 +175,7 @@
 static void __init sirfsoc_clockevent_init(void)
 {
 	sirfsoc_clockevent.cpumask = cpumask_of(0);
-	clockevents_config_and_register(&sirfsoc_clockevent, CLOCK_TICK_RATE,
+	clockevents_config_and_register(&sirfsoc_clockevent, PRIMA2_CLOCK_FREQ,
 					2, -2);
 }
 
@@ -190,8 +192,8 @@
 
 	rate = clk_get_rate(clk);
 
-	BUG_ON(rate < CLOCK_TICK_RATE);
-	BUG_ON(rate % CLOCK_TICK_RATE);
+	BUG_ON(rate < PRIMA2_CLOCK_FREQ);
+	BUG_ON(rate % PRIMA2_CLOCK_FREQ);
 
 	sirfsoc_timer_base = of_iomap(np, 0);
 	if (!sirfsoc_timer_base)
@@ -199,14 +201,16 @@
 
 	sirfsoc_timer_irq.irq = irq_of_parse_and_map(np, 0);
 
-	writel_relaxed(rate / CLOCK_TICK_RATE / 2 - 1, sirfsoc_timer_base + SIRFSOC_TIMER_DIV);
+	writel_relaxed(rate / PRIMA2_CLOCK_FREQ / 2 - 1,
+		       sirfsoc_timer_base + SIRFSOC_TIMER_DIV);
 	writel_relaxed(0, sirfsoc_timer_base + SIRFSOC_TIMER_COUNTER_LO);
 	writel_relaxed(0, sirfsoc_timer_base + SIRFSOC_TIMER_COUNTER_HI);
 	writel_relaxed(BIT(0), sirfsoc_timer_base + SIRFSOC_TIMER_STATUS);
 
-	BUG_ON(clocksource_register_hz(&sirfsoc_clocksource, CLOCK_TICK_RATE));
+	BUG_ON(clocksource_register_hz(&sirfsoc_clocksource,
+				       PRIMA2_CLOCK_FREQ));
 
-	sched_clock_register(sirfsoc_read_sched_clock, 64, CLOCK_TICK_RATE);
+	sched_clock_register(sirfsoc_read_sched_clock, 64, PRIMA2_CLOCK_FREQ);
 
 	BUG_ON(setup_irq(sirfsoc_timer_irq.irq, &sirfsoc_timer_irq));
 
diff --git a/drivers/input/misc/ixp4xx-beeper.c b/drivers/input/misc/ixp4xx-beeper.c
index 17ccba8..ed8e5e8 100644
--- a/drivers/input/misc/ixp4xx-beeper.c
+++ b/drivers/input/misc/ixp4xx-beeper.c
@@ -67,7 +67,7 @@
 	}
 
 	if (value > 20 && value < 32767)
-		count = (IXP4XX_TIMER_FREQ / (value * 4)) - 1;
+		count = (ixp4xx_timer_freq / (value * 4)) - 1;
 
 	ixp4xx_spkr_control(pin, count);
 
diff --git a/drivers/irqchip/exynos-combiner.c b/drivers/irqchip/exynos-combiner.c
index 40e6440..f8636a6 100644
--- a/drivers/irqchip/exynos-combiner.c
+++ b/drivers/irqchip/exynos-combiner.c
@@ -17,7 +17,6 @@
 #include <linux/irqchip/chained_irq.h>
 #include <linux/of_address.h>
 #include <linux/of_irq.h>
-#include <asm/mach/irq.h>
 
 #include "irqchip.h"
 
@@ -81,7 +80,7 @@
 	cascade_irq = irq_find_mapping(combiner_irq_domain, combiner_irq);
 
 	if (unlikely(!cascade_irq))
-		do_bad_IRQ(irq, desc);
+		handle_bad_irq(irq, desc);
 	else
 		generic_handle_irq(cascade_irq);
 
diff --git a/drivers/irqchip/irq-mmp.c b/drivers/irqchip/irq-mmp.c
index 2cb7cd0..470c5de 100644
--- a/drivers/irqchip/irq-mmp.c
+++ b/drivers/irqchip/irq-mmp.c
@@ -22,7 +22,7 @@
 #include <linux/of_irq.h>
 
 #include <asm/exception.h>
-#include <asm/mach/irq.h>
+#include <asm/hardirq.h>
 
 #include "irqchip.h"
 
diff --git a/drivers/rtc/rtc-at91sam9.c b/drivers/rtc/rtc-at91sam9.c
index 309b8b3..5963743 100644
--- a/drivers/rtc/rtc-at91sam9.c
+++ b/drivers/rtc/rtc-at91sam9.c
@@ -24,7 +24,7 @@
 
 #include <mach/at91_rtt.h>
 #include <mach/cpu.h>
-
+#include <mach/hardware.h>
 
 /*
  * This driver uses two configurable hardware resources that live in the
diff --git a/drivers/rtc/rtc-pxa.c b/drivers/rtc/rtc-pxa.c
index a355f2b..cccbf9d 100644
--- a/drivers/rtc/rtc-pxa.c
+++ b/drivers/rtc/rtc-pxa.c
@@ -32,7 +32,6 @@
 
 #include <mach/hardware.h>
 
-#define TIMER_FREQ		CLOCK_TICK_RATE
 #define RTC_DEF_DIVIDER		(32768 - 1)
 #define RTC_DEF_TRIM		0
 #define MAXFREQ_PERIODIC	1000
diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c
index a49f10d..91c0d88 100644
--- a/drivers/tty/serial/atmel_serial.c
+++ b/drivers/tty/serial/atmel_serial.c
@@ -35,21 +35,18 @@
 #include <linux/platform_device.h>
 #include <linux/of.h>
 #include <linux/of_device.h>
+#include <linux/of_gpio.h>
 #include <linux/dma-mapping.h>
 #include <linux/atmel_pdc.h>
 #include <linux/atmel_serial.h>
 #include <linux/uaccess.h>
 #include <linux/platform_data/atmel.h>
 #include <linux/timer.h>
+#include <linux/gpio.h>
 
 #include <asm/io.h>
 #include <asm/ioctls.h>
 
-#ifdef CONFIG_ARM
-#include <mach/cpu.h>
-#include <asm/gpio.h>
-#endif
-
 #define PDC_BUFFER_SIZE		512
 /* Revisit: We should calculate this based on the actual port settings */
 #define PDC_RX_TIMEOUT		(3 * 10)		/* 3 bytes */
@@ -168,6 +165,7 @@
 	struct circ_buf		rx_ring;
 
 	struct serial_rs485	rs485;		/* rs485 settings */
+	int			rts_gpio;	/* optional RTS GPIO */
 	unsigned int		tx_done_mask;
 	bool			is_usart;	/* usart or uart */
 	struct timer_list	uart_timer;	/* uart timer */
@@ -301,20 +299,16 @@
 	unsigned int mode;
 	struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
 
-#ifdef CONFIG_ARCH_AT91RM9200
-	if (cpu_is_at91rm9200()) {
-		/*
-		 * AT91RM9200 Errata #39: RTS0 is not internally connected
-		 * to PA21. We need to drive the pin manually.
-		 */
-		if (port->mapbase == AT91RM9200_BASE_US0) {
-			if (mctrl & TIOCM_RTS)
-				at91_set_gpio_value(AT91_PIN_PA21, 0);
-			else
-				at91_set_gpio_value(AT91_PIN_PA21, 1);
-		}
+	/*
+	 * AT91RM9200 Errata #39: RTS0 is not internally connected
+	 * to PA21. We need to drive the pin as a GPIO.
+	 */
+	if (gpio_is_valid(atmel_port->rts_gpio)) {
+		if (mctrl & TIOCM_RTS)
+			gpio_set_value(atmel_port->rts_gpio, 0);
+		else
+			gpio_set_value(atmel_port->rts_gpio, 1);
 	}
-#endif
 
 	if (mctrl & TIOCM_RTS)
 		control |= ATMEL_US_RTSEN;
@@ -2389,6 +2383,25 @@
 	port = &atmel_ports[ret];
 	port->backup_imr = 0;
 	port->uart.line = ret;
+	port->rts_gpio = -EINVAL; /* Invalid, zero could be valid */
+	if (pdata)
+		port->rts_gpio = pdata->rts_gpio;
+	else if (np)
+		port->rts_gpio = of_get_named_gpio(np, "rts-gpios", 0);
+
+	if (gpio_is_valid(port->rts_gpio)) {
+		ret = devm_gpio_request(&pdev->dev, port->rts_gpio, "RTS");
+		if (ret) {
+			dev_err(&pdev->dev, "error requesting RTS GPIO\n");
+			goto err;
+		}
+		/* Default to 1 as RTS is active low */
+		ret = gpio_direction_output(port->rts_gpio, 1);
+		if (ret) {
+			dev_err(&pdev->dev, "error setting up RTS GPIO\n");
+			goto err;
+		}
+	}
 
 	ret = atmel_init_port(port, pdev);
 	if (ret)
diff --git a/include/linux/platform_data/atmel.h b/include/linux/platform_data/atmel.h
index cea9f70..e26b0c1 100644
--- a/include/linux/platform_data/atmel.h
+++ b/include/linux/platform_data/atmel.h
@@ -84,6 +84,7 @@
 	short			use_dma_rx;	/* use receive DMA? */
 	void __iomem		*regs;		/* virt. base address, if any */
 	struct serial_rs485	rs485;		/* rs485 settings */
+	int			rts_gpio;	/* optional RTS GPIO */
 };
 
  /* Touchscreen Controller */