wl1271: Add config structure for connection management parameters
Add a configuration structure for connection management parameters, and
set default configuration values there.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
diff --git a/drivers/net/wireless/wl12xx/wl1271_conf.h b/drivers/net/wireless/wl12xx/wl1271_conf.h
index 3c5ce31..f08e509 100644
--- a/drivers/net/wireless/wl12xx/wl1271_conf.h
+++ b/drivers/net/wireless/wl12xx/wl1271_conf.h
@@ -441,10 +441,261 @@
};
+enum {
+ CONF_WAKE_UP_EVENT_BEACON = 0x01, /* Wake on every Beacon*/
+ CONF_WAKE_UP_EVENT_DTIM = 0x02, /* Wake on every DTIM*/
+ CONF_WAKE_UP_EVENT_N_DTIM = 0x04, /* Wake every Nth DTIM */
+ CONF_WAKE_UP_EVENT_N_BEACONS = 0x08, /* Wake every Nth beacon */
+ CONF_WAKE_UP_EVENT_BITS_MASK = 0x0F
+};
+
+#define CONF_MAX_BCN_FILT_IE_COUNT 32
+
+#define CONF_BCN_RULE_PASS_ON_CHANGE BIT(0)
+#define CONF_BCN_RULE_PASS_ON_APPEARANCE BIT(1)
+
+#define CONF_BCN_IE_OUI_LEN 3
+#define CONF_BCN_IE_VER_LEN 2
+
+struct conf_bcn_filt_rule {
+ /*
+ * IE number to which to associate a rule.
+ *
+ * Range: u8
+ */
+ u8 ie;
+
+ /*
+ * Rule to associate with the specific ie.
+ *
+ * Range: CONF_BCN_RULE_PASS_ON_*
+ */
+ u8 rule;
+
+ /*
+ * OUI for the vendor specifie IE (221)
+ */
+ u8 oui[CONF_BCN_IE_OUI_LEN];
+
+ /*
+ * Type for the vendor specifie IE (221)
+ */
+ u8 type;
+
+ /*
+ * Version for the vendor specifie IE (221)
+ */
+ u8 version[CONF_BCN_IE_VER_LEN];
+};
+
+#define CONF_MAX_RSSI_SNR_TRIGGERS 8
+
+enum {
+ CONF_TRIG_METRIC_RSSI_BEACON = 0,
+ CONF_TRIG_METRIC_RSSI_DATA,
+ CONF_TRIG_METRIC_SNR_BEACON,
+ CONF_TRIG_METRIC_SNR_DATA
+};
+
+enum {
+ CONF_TRIG_EVENT_TYPE_LEVEL = 0,
+ CONF_TRIG_EVENT_TYPE_EDGE
+};
+
+enum {
+ CONF_TRIG_EVENT_DIR_LOW = 0,
+ CONF_TRIG_EVENT_DIR_HIGH,
+ CONF_TRIG_EVENT_DIR_BIDIR
+};
+
+
+struct conf_sig_trigger {
+ /*
+ * The RSSI / SNR threshold value.
+ *
+ * FIXME: what is the range?
+ */
+ s16 threshold;
+
+ /*
+ * Minimum delay between two trigger events for this trigger in ms.
+ *
+ * Range: 0 - 60000
+ */
+ u16 pacing;
+
+ /*
+ * The measurement data source for this trigger.
+ *
+ * Range: CONF_TRIG_METRIC_*
+ */
+ u8 metric;
+
+ /*
+ * The trigger type of this trigger.
+ *
+ * Range: CONF_TRIG_EVENT_TYPE_*
+ */
+ u8 type;
+
+ /*
+ * The direction of the trigger.
+ *
+ * Range: CONF_TRIG_EVENT_DIR_*
+ */
+ u8 direction;
+
+ /*
+ * Hysteresis range of the trigger around the threshold (in dB)
+ *
+ * Range: u8
+ */
+ u8 hysteresis;
+
+ /*
+ * Index of the trigger rule.
+ *
+ * Range: 0 - CONF_MAX_RSSI_SNR_TRIGGERS-1
+ */
+ u8 index;
+
+ /*
+ * Enable / disable this rule (to use for clearing rules.)
+ *
+ * Range: 1 - Enabled, 2 - Not enabled
+ */
+ u8 enable;
+};
+
+struct conf_sig_weights {
+
+ /*
+ * RSSI from beacons average weight.
+ *
+ * Range: u8
+ */
+ u8 rssi_bcn_avg_weight;
+
+ /*
+ * RSSI from data average weight.
+ *
+ * Range: u8
+ */
+ u8 rssi_pkt_avg_weight;
+
+ /*
+ * SNR from beacons average weight.
+ *
+ * Range: u8
+ */
+ u8 snr_bcn_avg_weight;
+
+ /*
+ * SNR from data average weight.
+ *
+ * Range: u8
+ */
+ u8 snr_pkt_avg_weight;
+};
+
+enum conf_bcn_filt_mode {
+ CONF_BCN_FILT_MODE_DISABLED = 0,
+ CONF_BCN_FILT_MODE_ENABLED = 1
+};
+
+struct conf_conn_settings {
+ /*
+ * Firmware wakeup conditions configuration. The host may set only
+ * one bit.
+ *
+ * Range: CONF_WAKE_UP_EVENT_*
+ */
+ u8 wake_up_event;
+
+ /*
+ * Listen interval for beacons or Dtims.
+ *
+ * Range: 0 for beacon and Dtim wakeup
+ * 1-10 for x Dtims
+ * 1-255 for x beacons
+ */
+ u8 listen_interval;
+
+ /*
+ * Enable or disable the beacon filtering.
+ *
+ * Range: CONF_BCN_FILT_MODE_*
+ */
+ enum conf_bcn_filt_mode bcn_filt_mode;
+
+ /*
+ * Configure Beacon filter pass-thru rules.
+ */
+ u8 bcn_filt_ie_count;
+ struct conf_bcn_filt_rule bcn_filt_ie[CONF_MAX_BCN_FILT_IE_COUNT];
+
+ /*
+ * The number of consequtive beacons to lose, before the firmware
+ * becomes out of synch.
+ *
+ * Range: u32
+ */
+ u32 synch_fail_thold;
+
+ /*
+ * After out-of-synch, the number of TU's to wait without a further
+ * received beacon (or probe response) before issuing the BSS_EVENT_LOSE
+ * event.
+ *
+ * Range: u32
+ */
+ u32 bss_lose_timeout;
+
+ /*
+ * Beacon receive timeout.
+ *
+ * Range: u32
+ */
+ u32 beacon_rx_timeout;
+
+ /*
+ * Broadcast receive timeout.
+ *
+ * Range: u32
+ */
+ u32 broadcast_timeout;
+
+ /*
+ * Enable/disable reception of broadcast packets in power save mode
+ *
+ * Range: 1 - enable, 0 - disable
+ */
+ u8 rx_broadcast_in_ps;
+
+ /*
+ * Consequtive PS Poll failures before sending event to driver
+ *
+ * Range: u8
+ */
+ u8 ps_poll_threshold;
+
+ /*
+ * Configuration of signal (rssi/snr) triggers.
+ */
+ u8 sig_trigger_count;
+ struct conf_sig_trigger sig_trigger[CONF_MAX_RSSI_SNR_TRIGGERS];
+
+ /*
+ * Configuration of signal average weights.
+ */
+ struct conf_sig_weights sig_weights;
+};
+
struct conf_drv_settings {
struct conf_sg_settings sg;
struct conf_rx_settings rx;
struct conf_tx_settings tx;
+ struct conf_conn_settings conn;
};
#endif