hwmon: (ltc2978) Add support for LTC2980 and LTM2987
LTC2980 and LTM2987 are command compatible to LTC2977. They consist of
two LTC2977 on a single die, and are instantiated as two separate chips,
each supporting eight channels.
Suggested-by: Michael Jones <mike@proclivis.com>
Tested-by: Michael Jones <mike@proclivis.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
diff --git a/Documentation/devicetree/bindings/hwmon/ltc2978.txt b/Documentation/devicetree/bindings/hwmon/ltc2978.txt
index e434d5f..5dc2691 100644
--- a/Documentation/devicetree/bindings/hwmon/ltc2978.txt
+++ b/Documentation/devicetree/bindings/hwmon/ltc2978.txt
@@ -6,10 +6,12 @@
* "lltc,ltc2975"
* "lltc,ltc2977"
* "lltc,ltc2978"
+ * "lltc,ltc2980"
* "lltc,ltc3880"
* "lltc,ltc3882"
* "lltc,ltc3883"
* "lltc,ltc3887"
+ * "lltc,ltm2987"
* "lltc,ltm4676"
- reg: I2C slave address
@@ -21,7 +23,7 @@
Valid names of regulators depend on number of supplies supported per device:
* ltc2974, ltc2975 : vout0 - vout3
- * ltc2977 : vout0 - vout7
+ * ltc2977, ltc2980, ltm2987 : vout0 - vout7
* ltc2978 : vout0 - vout7
* ltc3880, ltc3882 : vout0 - vout1
* ltc3883 : vout0
diff --git a/Documentation/hwmon/ltc2978 b/Documentation/hwmon/ltc2978
index 7e98288..1583553 100644
--- a/Documentation/hwmon/ltc2978
+++ b/Documentation/hwmon/ltc2978
@@ -19,6 +19,10 @@
Addresses scanned: -
Datasheet: http://www.linear.com/product/ltc2978
http://www.linear.com/product/ltc2978a
+ * Linear Technology LTC2980
+ Prefix: 'ltc2980'
+ Addresses scanned: -
+ Datasheet: http://www.linear.com/product/ltc2980
* Linear Technology LTC3880
Prefix: 'ltc3880'
Addresses scanned: -
@@ -35,6 +39,10 @@
Prefix: 'ltc3887'
Addresses scanned: -
Datasheet: http://www.linear.com/product/ltc3887
+ * Linear Technology LTM2987
+ Prefix: 'ltm2987'
+ Addresses scanned: -
+ Datasheet: http://www.linear.com/product/ltm2987
* Linear Technology LTM4676
Prefix: 'ltm4676'
Addresses scanned: -
@@ -49,9 +57,15 @@
LTC2974 and LTC2975 are quad digital power supply managers.
LTC2978 is an octal power supply monitor.
LTC2977 is a pin compatible replacement for LTC2978.
+LTC2980 is a 16-channel Power System Manager, consisting of two LTC2977
+in a single die. The chip is instantiated and reported as two separate chips
+on two different I2C bus addresses.
LTC3880, LTC3882, and LTC3887 are dual output poly-phase step-down DC/DC
controllers.
LTC3883 is a single phase step-down DC/DC controller.
+LTM2987 is a 16-channel Power System Manager with two LTC2977 plus
+additional components on a single die. The chip is instantiated and reported
+as two separate chips on two different I2C bus addresses.
LTM4676 is a dual 13A or single 26A uModule regulator.
@@ -75,24 +89,29 @@
in1_input Measured input voltage.
in1_min Minimum input voltage.
in1_max Maximum input voltage.
- LTC2974, LTC2975, LTC2977, and LTC2978 only.
+ LTC2974, LTC2975, LTC2977, LTC2980, LTC2978, and
+ LTM2987 only.
in1_lcrit Critical minimum input voltage.
- LTC2974, LTC2975, LTC2977, and LTC2978 only.
+ LTC2974, LTC2975, LTC2977, LTC2980, LTC2978, and
+ LTM2987 only.
in1_crit Critical maximum input voltage.
in1_min_alarm Input voltage low alarm.
in1_max_alarm Input voltage high alarm.
- LTC2974, LTC2975, LTC2977, and LTC2978 only.
+ LTC2974, LTC2975, LTC2977, LTC2980, LTC2978, and
+ LTM2987 only.
in1_lcrit_alarm Input voltage critical low alarm.
- LTC2974, LTC2975, LTC2977, and LTC2978 only.
+ LTC2974, LTC2975, LTC2977, LTC2980, LTC2978, and
+ LTM2987 only.
in1_crit_alarm Input voltage critical high alarm.
in1_lowest Lowest input voltage.
- LTC2974, LTC2975, LTC2977, and LTC2978 only.
+ LTC2974, LTC2975, LTC2977, LTC2980, LTC2978, and
+ LTM2987 only.
in1_highest Highest input voltage.
in1_reset_history Reset input voltage history.
in[N]_label "vout[1-8]".
LTC2974, LTC2975: N=2-5
- LTC2977: N=2-9
+ LTC2977, LTC2980, LTM2987: N=2-9
LTC2978: N=2-9
LTC3880, LTC3882, LTC3887, LTM4676: N=2-3
LTC3883: N=2
@@ -113,24 +132,28 @@
temp[N]_input Measured temperature.
On LTC2974 and LTC2975, temp[1-4] report external
temperatures, and temp5 reports the chip temperature.
- On LTC2977 and LTC2978, only one temperature measurement
- is supported and reports the chip temperature.
+ On LTC2977, LTC2980, LTC2978, and LTM2987, only one
+ temperature measurement is supported and reports
+ the chip temperature.
On LTC3880, LTC3882, LTC3887, and LTM4676, temp1 and
temp2 report external temperatures, and temp3 reports
the chip temperature.
On LTC3883, temp1 reports an external temperature,
and temp2 reports the chip temperature.
-temp[N]_min Mimimum temperature. LTC2974, LCT2977, and LTC2978 only.
+temp[N]_min Mimimum temperature. LTC2974, LCT2977, LTM2980, LTC2978,
+ and LTM2987 only.
temp[N]_max Maximum temperature.
temp[N]_lcrit Critical low temperature.
temp[N]_crit Critical high temperature.
temp[N]_min_alarm Temperature low alarm.
- LTC2974, LTC2975, LTC2977, and LTC2978 only.
+ LTC2974, LTC2975, LTC2977, LTM2980, LTC2978, and
+ LTM2987 only.
temp[N]_max_alarm Temperature high alarm.
temp[N]_lcrit_alarm Temperature critical low alarm.
temp[N]_crit_alarm Temperature critical high alarm.
temp[N]_lowest Lowest measured temperature.
- LTC2974, LTC2975, LTC2977, and LTC2978 only.
+ LTC2974, LTC2975, LTC2977, LTM2980, LTC2978, and
+ LTM2987 only.
Not supported for chip temperature sensor on LTC2974 and
LTC2975.
temp[N]_highest Highest measured temperature. Not supported for chip
@@ -143,7 +166,7 @@
power[N]_label "pout[1-4]".
LTC2974, LTC2975: N=1-4
- LTC2977: Not supported
+ LTC2977, LTC2980, LTM2987: Not supported
LTC2978: Not supported
LTC3880, LTC3882, LTC3887, LTM4676: N=1-2
LTC3883: N=2
@@ -158,7 +181,7 @@
curr[N]_label "iout[1-4]".
LTC2974, LTC2975: N=1-4
- LTC2977: not supported
+ LTC2977, LTC2980, LTM2987: not supported
LTC2978: not supported
LTC3880, LTC3882, LTC3887, LTM4676: N=2-3
LTC3883: N=2
diff --git a/drivers/hwmon/pmbus/Kconfig b/drivers/hwmon/pmbus/Kconfig
index 8279727..af778ae 100644
--- a/drivers/hwmon/pmbus/Kconfig
+++ b/drivers/hwmon/pmbus/Kconfig
@@ -52,8 +52,8 @@
default n
help
If you say yes here you get hardware monitoring support for Linear
- Technology LTC2974, LTC2975, LTC2977, LTC2978, LTC3880, LTC3883,
- LTC3887, and LTM4676.
+ Technology LTC2974, LTC2975, LTC2977, LTC2978, LTC2980, LTC3880,
+ LTC3883, LTC3887, LTCM2987, and LTM4676.
This driver can also be built as a module. If so, the module will
be called ltc2978.
diff --git a/drivers/hwmon/pmbus/ltc2978.c b/drivers/hwmon/pmbus/ltc2978.c
index e9d3f82..48dcde0 100644
--- a/drivers/hwmon/pmbus/ltc2978.c
+++ b/drivers/hwmon/pmbus/ltc2978.c
@@ -24,8 +24,8 @@
#include <linux/regulator/driver.h>
#include "pmbus.h"
-enum chips { ltc2974, ltc2975, ltc2977, ltc2978, ltc3880, ltc3882, ltc3883,
- ltc3887, ltm4676 };
+enum chips { ltc2974, ltc2975, ltc2977, ltc2978, ltc2980, ltc3880, ltc3882,
+ ltc3883, ltc3887, ltm2987, ltm4676 };
/* Common for all chips */
#define LTC2978_MFR_VOUT_PEAK 0xdd
@@ -33,7 +33,7 @@
#define LTC2978_MFR_TEMPERATURE_PEAK 0xdf
#define LTC2978_MFR_SPECIAL_ID 0xe7 /* Undocumented on LTC3882 */
-/* LTC2974, LTC2975, LCT2977, and LTC2978 */
+/* LTC2974, LTC2975, LCT2977, LTC2980, LTC2978, and LTM2987 */
#define LTC2978_MFR_VOUT_MIN 0xfb
#define LTC2978_MFR_VIN_MIN 0xfc
#define LTC2978_MFR_TEMPERATURE_MIN 0xfd
@@ -63,11 +63,15 @@
#define LTC2977_ID 0x0130
#define LTC2978_ID_REV1 0x0110 /* Early revision */
#define LTC2978_ID_REV2 0x0120
+#define LTC2980_ID_A 0x8030 /* A/B for two die IDs */
+#define LTC2980_ID_B 0x8040
#define LTC3880_ID 0x4020
#define LTC3882_ID 0x4200
#define LTC3882_ID_D1 0x4240 /* Dash 1 */
#define LTC3883_ID 0x4300
#define LTC3887_ID 0x4700
+#define LTM2987_ID_A 0x8010 /* A/B for two die IDs */
+#define LTM2987_ID_B 0x8020
#define LTM4676_ID_REV1 0x4400
#define LTM4676_ID_REV2 0x4480
#define LTM4676A_ID 0x47e0
@@ -409,10 +413,12 @@
{"ltc2975", ltc2975},
{"ltc2977", ltc2977},
{"ltc2978", ltc2978},
+ {"ltc2980", ltc2980},
{"ltc3880", ltc3880},
{"ltc3882", ltc3882},
{"ltc3883", ltc3883},
{"ltc3887", ltc3887},
+ {"ltm2987", ltm2987},
{"ltm4676", ltm4676},
{}
};
@@ -471,6 +477,8 @@
return ltc2977;
else if (chip_id == LTC2978_ID_REV1 || chip_id == LTC2978_ID_REV2)
return ltc2978;
+ else if (chip_id == LTC2980_ID_A || chip_id == LTC2980_ID_B)
+ return ltc2980;
else if (chip_id == LTC3880_ID)
return ltc3880;
else if (chip_id == LTC3882_ID || chip_id == LTC3882_ID_D1)
@@ -479,6 +487,8 @@
return ltc3883;
else if (chip_id == LTC3887_ID)
return ltc3887;
+ else if (chip_id == LTM2987_ID_A || chip_id == LTM2987_ID_B)
+ return ltm2987;
else if (chip_id == LTM4676_ID_REV1 || chip_id == LTM4676_ID_REV2 ||
chip_id == LTM4676A_ID)
return ltm4676;
@@ -559,6 +569,8 @@
break;
case ltc2977:
case ltc2978:
+ case ltc2980:
+ case ltm2987:
info->read_word_data = ltc2978_read_word_data;
info->pages = LTC2978_NUM_PAGES;
info->func[0] = PMBUS_HAVE_VIN | PMBUS_HAVE_STATUS_INPUT
@@ -634,10 +646,12 @@
{ .compatible = "lltc,ltc2975" },
{ .compatible = "lltc,ltc2977" },
{ .compatible = "lltc,ltc2978" },
+ { .compatible = "lltc,ltc2980" },
{ .compatible = "lltc,ltc3880" },
{ .compatible = "lltc,ltc3882" },
{ .compatible = "lltc,ltc3883" },
{ .compatible = "lltc,ltc3887" },
+ { .compatible = "lltc,ltm2987" },
{ .compatible = "lltc,ltm4676" },
{ }
};