| /* |
| * include/asm-arm/arch-ixp2000/ixp2000-regs.h |
| * |
| * Chipset register definitions for IXP2400/2800 based systems. |
| * |
| * Original Author: Naeem Afzal <naeem.m.afzal@intel.com> |
| * |
| * Maintainer: Deepak Saxena <dsaxena@plexity.net> |
| * |
| * Copyright (C) 2002 Intel Corp. |
| * Copyright (C) 2003-2004 MontaVista Software, Inc. |
| * |
| * This program is free software; you can redistribute it and/or modify it |
| * under the terms of the GNU General Public License as published by the |
| * Free Software Foundation; either version 2 of the License, or (at your |
| * option) any later version. |
| */ |
| #ifndef _IXP2000_REGS_H_ |
| #define _IXP2000_REGS_H_ |
| |
| /* |
| * IXP2000 linux memory map: |
| * |
| * virt phys size |
| * fb000000 db000000 16M PCI CFG1 |
| * fc000000 da000000 16M PCI CFG0 |
| * fd000000 d8000000 16M PCI I/O |
| * fe[0-7]00000 8M per-platform mappings |
| * feb00000 c8000000 1M MSF |
| * fec00000 df000000 1M PCI CSRs |
| * fed00000 de000000 1M PCI CREG |
| * fee00000 d6000000 1M INTCTL |
| * fef00000 c0000000 1M CAP |
| */ |
| |
| /* |
| * Static I/O regions. |
| * |
| * Most of the registers are clumped in 4K regions spread throughout |
| * the 0xc0000000 -> 0xc0100000 address range, but we just map in |
| * the whole range using a single 1 MB section instead of small |
| * 4K pages. This has two advantages for us: |
| * |
| * 1) We use only one TLB entry for large number of on-chip I/O devices. |
| * |
| * 2) We can easily set the Section attributes to XCB=101 on the IXP2400 |
| * as required per erratum #66. We accomplish this by using a |
| * new MT_IXP2000_DEVICE memory type with the bits set as required. |
| * |
| * CAP stands for CSR Access Proxy. |
| * |
| * If you change the virtual address of this mapping, please propagate |
| * the change to arch/arm/kernel/debug.S, which hardcodes the virtual |
| * address of the UART located in this region. |
| */ |
| |
| #define IXP2000_CAP_PHYS_BASE 0xc0000000 |
| #define IXP2000_CAP_VIRT_BASE 0xfef00000 |
| #define IXP2000_CAP_SIZE 0x00100000 |
| |
| /* |
| * Addresses for specific on-chip peripherals. |
| */ |
| #define IXP2000_SLOWPORT_CSR_VIRT_BASE 0xfef80000 |
| #define IXP2000_GLOBAL_REG_VIRT_BASE 0xfef04000 |
| #define IXP2000_UART_PHYS_BASE 0xc0030000 |
| #define IXP2000_UART_VIRT_BASE 0xfef30000 |
| #define IXP2000_TIMER_VIRT_BASE 0xfef20000 |
| #define IXP2000_UENGINE_CSR_VIRT_BASE 0xfef18000 |
| #define IXP2000_GPIO_VIRT_BASE 0xfef10000 |
| |
| /* |
| * Devices outside of the 0xc0000000 -> 0xc0100000 range. The virtual |
| * addresses of the INTCTL and PCI_CSR mappings are hardcoded in |
| * entry-macro.S, so if you ever change these please propagate |
| * the change. |
| */ |
| #define IXP2000_INTCTL_PHYS_BASE 0xd6000000 |
| #define IXP2000_INTCTL_VIRT_BASE 0xfee00000 |
| #define IXP2000_INTCTL_SIZE 0x00100000 |
| |
| #define IXP2000_PCI_CREG_PHYS_BASE 0xde000000 |
| #define IXP2000_PCI_CREG_VIRT_BASE 0xfed00000 |
| #define IXP2000_PCI_CREG_SIZE 0x00100000 |
| |
| #define IXP2000_PCI_CSR_PHYS_BASE 0xdf000000 |
| #define IXP2000_PCI_CSR_VIRT_BASE 0xfec00000 |
| #define IXP2000_PCI_CSR_SIZE 0x00100000 |
| |
| #define IXP2000_MSF_PHYS_BASE 0xc8000000 |
| #define IXP2000_MSF_VIRT_BASE 0xfeb00000 |
| #define IXP2000_MSF_SIZE 0x00100000 |
| |
| #define IXP2000_PCI_IO_PHYS_BASE 0xd8000000 |
| #define IXP2000_PCI_IO_VIRT_BASE 0xfd000000 |
| #define IXP2000_PCI_IO_SIZE 0x01000000 |
| |
| #define IXP2000_PCI_CFG0_PHYS_BASE 0xda000000 |
| #define IXP2000_PCI_CFG0_VIRT_BASE 0xfc000000 |
| #define IXP2000_PCI_CFG0_SIZE 0x01000000 |
| |
| #define IXP2000_PCI_CFG1_PHYS_BASE 0xdb000000 |
| #define IXP2000_PCI_CFG1_VIRT_BASE 0xfb000000 |
| #define IXP2000_PCI_CFG1_SIZE 0x01000000 |
| |
| /* |
| * Timers |
| */ |
| #define IXP2000_TIMER_REG(x) ((volatile unsigned long*)(IXP2000_TIMER_VIRT_BASE | (x))) |
| /* Timer control */ |
| #define IXP2000_T1_CTL IXP2000_TIMER_REG(0x00) |
| #define IXP2000_T2_CTL IXP2000_TIMER_REG(0x04) |
| #define IXP2000_T3_CTL IXP2000_TIMER_REG(0x08) |
| #define IXP2000_T4_CTL IXP2000_TIMER_REG(0x0c) |
| /* Store initial value */ |
| #define IXP2000_T1_CLD IXP2000_TIMER_REG(0x10) |
| #define IXP2000_T2_CLD IXP2000_TIMER_REG(0x14) |
| #define IXP2000_T3_CLD IXP2000_TIMER_REG(0x18) |
| #define IXP2000_T4_CLD IXP2000_TIMER_REG(0x1c) |
| /* Read current value */ |
| #define IXP2000_T1_CSR IXP2000_TIMER_REG(0x20) |
| #define IXP2000_T2_CSR IXP2000_TIMER_REG(0x24) |
| #define IXP2000_T3_CSR IXP2000_TIMER_REG(0x28) |
| #define IXP2000_T4_CSR IXP2000_TIMER_REG(0x2c) |
| /* Clear associated timer interrupt */ |
| #define IXP2000_T1_CLR IXP2000_TIMER_REG(0x30) |
| #define IXP2000_T2_CLR IXP2000_TIMER_REG(0x34) |
| #define IXP2000_T3_CLR IXP2000_TIMER_REG(0x38) |
| #define IXP2000_T4_CLR IXP2000_TIMER_REG(0x3c) |
| /* Timer watchdog enable for T4 */ |
| #define IXP2000_TWDE IXP2000_TIMER_REG(0x40) |
| |
| #define WDT_ENABLE 0x00000001 |
| #define TIMER_DIVIDER_256 0x00000008 |
| #define TIMER_ENABLE 0x00000080 |
| #define IRQ_MASK_TIMER1 (1 << 4) |
| |
| /* |
| * Interrupt controller registers |
| */ |
| #define IXP2000_INTCTL_REG(x) (volatile unsigned long*)(IXP2000_INTCTL_VIRT_BASE | (x)) |
| #define IXP2000_IRQ_STATUS IXP2000_INTCTL_REG(0x08) |
| #define IXP2000_IRQ_ENABLE IXP2000_INTCTL_REG(0x10) |
| #define IXP2000_IRQ_ENABLE_SET IXP2000_INTCTL_REG(0x10) |
| #define IXP2000_IRQ_ENABLE_CLR IXP2000_INTCTL_REG(0x18) |
| #define IXP2000_FIQ_ENABLE_CLR IXP2000_INTCTL_REG(0x14) |
| #define IXP2000_IRQ_ERR_STATUS IXP2000_INTCTL_REG(0x24) |
| #define IXP2000_IRQ_ERR_ENABLE_SET IXP2000_INTCTL_REG(0x2c) |
| #define IXP2000_FIQ_ERR_ENABLE_CLR IXP2000_INTCTL_REG(0x30) |
| #define IXP2000_IRQ_ERR_ENABLE_CLR IXP2000_INTCTL_REG(0x34) |
| #define IXP2000_IRQ_THD_RAW_STATUS_A_0 IXP2000_INTCTL_REG(0x60) |
| #define IXP2000_IRQ_THD_RAW_STATUS_A_1 IXP2000_INTCTL_REG(0x64) |
| #define IXP2000_IRQ_THD_RAW_STATUS_A_2 IXP2000_INTCTL_REG(0x68) |
| #define IXP2000_IRQ_THD_RAW_STATUS_A_3 IXP2000_INTCTL_REG(0x6c) |
| #define IXP2000_IRQ_THD_RAW_STATUS_B_0 IXP2000_INTCTL_REG(0x80) |
| #define IXP2000_IRQ_THD_RAW_STATUS_B_1 IXP2000_INTCTL_REG(0x84) |
| #define IXP2000_IRQ_THD_RAW_STATUS_B_2 IXP2000_INTCTL_REG(0x88) |
| #define IXP2000_IRQ_THD_RAW_STATUS_B_3 IXP2000_INTCTL_REG(0x8c) |
| #define IXP2000_IRQ_THD_STATUS_A_0 IXP2000_INTCTL_REG(0xe0) |
| #define IXP2000_IRQ_THD_STATUS_A_1 IXP2000_INTCTL_REG(0xe4) |
| #define IXP2000_IRQ_THD_STATUS_A_2 IXP2000_INTCTL_REG(0xe8) |
| #define IXP2000_IRQ_THD_STATUS_A_3 IXP2000_INTCTL_REG(0xec) |
| #define IXP2000_IRQ_THD_STATUS_B_0 IXP2000_INTCTL_REG(0x100) |
| #define IXP2000_IRQ_THD_STATUS_B_1 IXP2000_INTCTL_REG(0x104) |
| #define IXP2000_IRQ_THD_STATUS_B_2 IXP2000_INTCTL_REG(0x108) |
| #define IXP2000_IRQ_THD_STATUS_B_3 IXP2000_INTCTL_REG(0x10c) |
| #define IXP2000_IRQ_THD_ENABLE_SET_A_0 IXP2000_INTCTL_REG(0x160) |
| #define IXP2000_IRQ_THD_ENABLE_SET_A_1 IXP2000_INTCTL_REG(0x164) |
| #define IXP2000_IRQ_THD_ENABLE_SET_A_2 IXP2000_INTCTL_REG(0x168) |
| #define IXP2000_IRQ_THD_ENABLE_SET_A_3 IXP2000_INTCTL_REG(0x16c) |
| #define IXP2000_IRQ_THD_ENABLE_SET_B_0 IXP2000_INTCTL_REG(0x180) |
| #define IXP2000_IRQ_THD_ENABLE_SET_B_1 IXP2000_INTCTL_REG(0x184) |
| #define IXP2000_IRQ_THD_ENABLE_SET_B_2 IXP2000_INTCTL_REG(0x188) |
| #define IXP2000_IRQ_THD_ENABLE_SET_B_3 IXP2000_INTCTL_REG(0x18c) |
| #define IXP2000_IRQ_THD_ENABLE_CLEAR_A_0 IXP2000_INTCTL_REG(0x1e0) |
| #define IXP2000_IRQ_THD_ENABLE_CLEAR_A_1 IXP2000_INTCTL_REG(0x1e4) |
| #define IXP2000_IRQ_THD_ENABLE_CLEAR_A_2 IXP2000_INTCTL_REG(0x1e8) |
| #define IXP2000_IRQ_THD_ENABLE_CLEAR_A_3 IXP2000_INTCTL_REG(0x1ec) |
| #define IXP2000_IRQ_THD_ENABLE_CLEAR_B_0 IXP2000_INTCTL_REG(0x200) |
| #define IXP2000_IRQ_THD_ENABLE_CLEAR_B_1 IXP2000_INTCTL_REG(0x204) |
| #define IXP2000_IRQ_THD_ENABLE_CLEAR_B_2 IXP2000_INTCTL_REG(0x208) |
| #define IXP2000_IRQ_THD_ENABLE_CLEAR_B_3 IXP2000_INTCTL_REG(0x20c) |
| |
| /* |
| * Mask of valid IRQs in the 32-bit IRQ register. We use |
| * this to mark certain IRQs as being invalid. |
| */ |
| #define IXP2000_VALID_IRQ_MASK 0x0f0fffff |
| |
| /* |
| * PCI config register access from core |
| */ |
| #define IXP2000_PCI_CREG(x) (volatile unsigned long*)(IXP2000_PCI_CREG_VIRT_BASE | (x)) |
| #define IXP2000_PCI_CMDSTAT IXP2000_PCI_CREG(0x04) |
| #define IXP2000_PCI_CSR_BAR IXP2000_PCI_CREG(0x10) |
| #define IXP2000_PCI_SRAM_BAR IXP2000_PCI_CREG(0x14) |
| #define IXP2000_PCI_SDRAM_BAR IXP2000_PCI_CREG(0x18) |
| |
| /* |
| * PCI CSRs |
| */ |
| #define IXP2000_PCI_CSR(x) (volatile unsigned long*)(IXP2000_PCI_CSR_VIRT_BASE | (x)) |
| |
| /* |
| * PCI outbound interrupts |
| */ |
| #define IXP2000_PCI_OUT_INT_STATUS IXP2000_PCI_CSR(0x30) |
| #define IXP2000_PCI_OUT_INT_MASK IXP2000_PCI_CSR(0x34) |
| /* |
| * PCI communications |
| */ |
| #define IXP2000_PCI_MAILBOX0 IXP2000_PCI_CSR(0x50) |
| #define IXP2000_PCI_MAILBOX1 IXP2000_PCI_CSR(0x54) |
| #define IXP2000_PCI_MAILBOX2 IXP2000_PCI_CSR(0x58) |
| #define IXP2000_PCI_MAILBOX3 IXP2000_PCI_CSR(0x5C) |
| #define IXP2000_XSCALE_DOORBELL IXP2000_PCI_CSR(0x60) |
| #define IXP2000_XSCALE_DOORBELL_SETUP IXP2000_PCI_CSR(0x64) |
| #define IXP2000_PCI_DOORBELL IXP2000_PCI_CSR(0x70) |
| #define IXP2000_PCI_DOORBELL_SETUP IXP2000_PCI_CSR(0x74) |
| |
| /* |
| * DMA engines |
| */ |
| #define IXP2000_PCI_CH1_BYTE_CNT IXP2000_PCI_CSR(0x80) |
| #define IXP2000_PCI_CH1_ADDR IXP2000_PCI_CSR(0x84) |
| #define IXP2000_PCI_CH1_DRAM_ADDR IXP2000_PCI_CSR(0x88) |
| #define IXP2000_PCI_CH1_DESC_PTR IXP2000_PCI_CSR(0x8C) |
| #define IXP2000_PCI_CH1_CNTRL IXP2000_PCI_CSR(0x90) |
| #define IXP2000_PCI_CH1_ME_PARAM IXP2000_PCI_CSR(0x94) |
| #define IXP2000_PCI_CH2_BYTE_CNT IXP2000_PCI_CSR(0xA0) |
| #define IXP2000_PCI_CH2_ADDR IXP2000_PCI_CSR(0xA4) |
| #define IXP2000_PCI_CH2_DRAM_ADDR IXP2000_PCI_CSR(0xA8) |
| #define IXP2000_PCI_CH2_DESC_PTR IXP2000_PCI_CSR(0xAC) |
| #define IXP2000_PCI_CH2_CNTRL IXP2000_PCI_CSR(0xB0) |
| #define IXP2000_PCI_CH2_ME_PARAM IXP2000_PCI_CSR(0xB4) |
| #define IXP2000_PCI_CH3_BYTE_CNT IXP2000_PCI_CSR(0xC0) |
| #define IXP2000_PCI_CH3_ADDR IXP2000_PCI_CSR(0xC4) |
| #define IXP2000_PCI_CH3_DRAM_ADDR IXP2000_PCI_CSR(0xC8) |
| #define IXP2000_PCI_CH3_DESC_PTR IXP2000_PCI_CSR(0xCC) |
| #define IXP2000_PCI_CH3_CNTRL IXP2000_PCI_CSR(0xD0) |
| #define IXP2000_PCI_CH3_ME_PARAM IXP2000_PCI_CSR(0xD4) |
| #define IXP2000_DMA_INF_MODE IXP2000_PCI_CSR(0xE0) |
| /* |
| * Size masks for BARs |
| */ |
| #define IXP2000_PCI_SRAM_BASE_ADDR_MASK IXP2000_PCI_CSR(0xFC) |
| #define IXP2000_PCI_DRAM_BASE_ADDR_MASK IXP2000_PCI_CSR(0x100) |
| /* |
| * Control and uEngine related |
| */ |
| #define IXP2000_PCI_CONTROL IXP2000_PCI_CSR(0x13C) |
| #define IXP2000_PCI_ADDR_EXT IXP2000_PCI_CSR(0x140) |
| #define IXP2000_PCI_ME_PUSH_STATUS IXP2000_PCI_CSR(0x148) |
| #define IXP2000_PCI_ME_PUSH_EN IXP2000_PCI_CSR(0x14C) |
| #define IXP2000_PCI_ERR_STATUS IXP2000_PCI_CSR(0x150) |
| #define IXP2000_PCI_ERR_ENABLE IXP2000_PCI_CSR(0x154) |
| /* |
| * Inbound PCI interrupt control |
| */ |
| #define IXP2000_PCI_XSCALE_INT_STATUS IXP2000_PCI_CSR(0x158) |
| #define IXP2000_PCI_XSCALE_INT_ENABLE IXP2000_PCI_CSR(0x15C) |
| |
| #define IXP2000_PCICNTL_PNR (1<<17) /* PCI not Reset bit of PCI_CONTROL */ |
| #define IXP2000_PCICNTL_PCF (1<<28) /* PCI Central function bit */ |
| #define IXP2000_XSCALE_INT (1<<1) /* Interrupt from XScale to PCI */ |
| |
| /* These are from the IRQ register in the PCI ISR register */ |
| #define PCI_CONTROL_BE_DEO (1 << 22) /* Big Endian Data Enable Out */ |
| #define PCI_CONTROL_BE_DEI (1 << 21) /* Big Endian Data Enable In */ |
| #define PCI_CONTROL_BE_BEO (1 << 20) /* Big Endian Byte Enable Out */ |
| #define PCI_CONTROL_BE_BEI (1 << 19) /* Big Endian Byte Enable In */ |
| #define PCI_CONTROL_IEE (1 << 17) /* I/O cycle Endian swap Enable */ |
| |
| #define IXP2000_PCI_RST_REL (1 << 2) |
| #define CFG_RST_DIR (*IXP2000_PCI_CONTROL & IXP2000_PCICNTL_PCF) |
| #define CFG_PCI_BOOT_HOST (1 << 2) |
| #define CFG_BOOT_PROM (1 << 1) |
| |
| /* |
| * SlowPort CSRs |
| * |
| * The slowport is used to access things like flash, SONET framer control |
| * ports, slave microprocessors, CPLDs, and others of chip memory mapped |
| * peripherals. |
| */ |
| #define SLOWPORT_CSR(x) (volatile unsigned long*)(IXP2000_SLOWPORT_CSR_VIRT_BASE | (x)) |
| |
| #define IXP2000_SLOWPORT_CCR SLOWPORT_CSR(0x00) |
| #define IXP2000_SLOWPORT_WTC1 SLOWPORT_CSR(0x04) |
| #define IXP2000_SLOWPORT_WTC2 SLOWPORT_CSR(0x08) |
| #define IXP2000_SLOWPORT_RTC1 SLOWPORT_CSR(0x0c) |
| #define IXP2000_SLOWPORT_RTC2 SLOWPORT_CSR(0x10) |
| #define IXP2000_SLOWPORT_FSR SLOWPORT_CSR(0x14) |
| #define IXP2000_SLOWPORT_PCR SLOWPORT_CSR(0x18) |
| #define IXP2000_SLOWPORT_ADC SLOWPORT_CSR(0x1C) |
| #define IXP2000_SLOWPORT_FAC SLOWPORT_CSR(0x20) |
| #define IXP2000_SLOWPORT_FRM SLOWPORT_CSR(0x24) |
| #define IXP2000_SLOWPORT_FIN SLOWPORT_CSR(0x28) |
| |
| /* |
| * CCR values. |
| * The CCR configures the clock division for the slowport interface. |
| */ |
| #define SLOWPORT_CCR_DIV_1 0x00 |
| #define SLOWPORT_CCR_DIV_2 0x01 |
| #define SLOWPORT_CCR_DIV_4 0x02 |
| #define SLOWPORT_CCR_DIV_6 0x03 |
| #define SLOWPORT_CCR_DIV_8 0x04 |
| #define SLOWPORT_CCR_DIV_10 0x05 |
| #define SLOWPORT_CCR_DIV_12 0x06 |
| #define SLOWPORT_CCR_DIV_14 0x07 |
| #define SLOWPORT_CCR_DIV_16 0x08 |
| #define SLOWPORT_CCR_DIV_18 0x09 |
| #define SLOWPORT_CCR_DIV_20 0x0a |
| #define SLOWPORT_CCR_DIV_22 0x0b |
| #define SLOWPORT_CCR_DIV_24 0x0c |
| #define SLOWPORT_CCR_DIV_26 0x0d |
| #define SLOWPORT_CCR_DIV_28 0x0e |
| #define SLOWPORT_CCR_DIV_30 0x0f |
| |
| /* |
| * PCR values. PCR configure the mode of the interface. |
| */ |
| #define SLOWPORT_MODE_FLASH 0x00 |
| #define SLOWPORT_MODE_LUCENT 0x01 |
| #define SLOWPORT_MODE_PMC_SIERRA 0x02 |
| #define SLOWPORT_MODE_INTEL_UP 0x03 |
| #define SLOWPORT_MODE_MOTOROLA_UP 0x04 |
| |
| /* |
| * ADC values. Defines data and address bus widths. |
| */ |
| #define SLOWPORT_ADDR_WIDTH_8 0x00 |
| #define SLOWPORT_ADDR_WIDTH_16 0x01 |
| #define SLOWPORT_ADDR_WIDTH_24 0x02 |
| #define SLOWPORT_ADDR_WIDTH_32 0x03 |
| #define SLOWPORT_DATA_WIDTH_8 0x00 |
| #define SLOWPORT_DATA_WIDTH_16 0x10 |
| #define SLOWPORT_DATA_WIDTH_24 0x20 |
| #define SLOWPORT_DATA_WIDTH_32 0x30 |
| |
| /* |
| * Masks and shifts for various fields in the WTC and RTC registers. |
| */ |
| #define SLOWPORT_WRTC_MASK_HD 0x0003 |
| #define SLOWPORT_WRTC_MASK_SU 0x003c |
| #define SLOWPORT_WRTC_MASK_PW 0x03c0 |
| |
| #define SLOWPORT_WRTC_SHIFT_HD 0x00 |
| #define SLOWPORT_WRTC_SHIFT_SU 0x02 |
| #define SLOWPORT_WRTC_SHFIT_PW 0x06 |
| |
| |
| /* |
| * GPIO registers & GPIO interface. |
| */ |
| #define IXP2000_GPIO_REG(x) ((volatile unsigned long*)(IXP2000_GPIO_VIRT_BASE+(x))) |
| #define IXP2000_GPIO_PLR IXP2000_GPIO_REG(0x00) |
| #define IXP2000_GPIO_PDPR IXP2000_GPIO_REG(0x04) |
| #define IXP2000_GPIO_PDSR IXP2000_GPIO_REG(0x08) |
| #define IXP2000_GPIO_PDCR IXP2000_GPIO_REG(0x0c) |
| #define IXP2000_GPIO_POPR IXP2000_GPIO_REG(0x10) |
| #define IXP2000_GPIO_POSR IXP2000_GPIO_REG(0x14) |
| #define IXP2000_GPIO_POCR IXP2000_GPIO_REG(0x18) |
| #define IXP2000_GPIO_REDR IXP2000_GPIO_REG(0x1c) |
| #define IXP2000_GPIO_FEDR IXP2000_GPIO_REG(0x20) |
| #define IXP2000_GPIO_EDSR IXP2000_GPIO_REG(0x24) |
| #define IXP2000_GPIO_LSHR IXP2000_GPIO_REG(0x28) |
| #define IXP2000_GPIO_LSLR IXP2000_GPIO_REG(0x2c) |
| #define IXP2000_GPIO_LDSR IXP2000_GPIO_REG(0x30) |
| #define IXP2000_GPIO_INER IXP2000_GPIO_REG(0x34) |
| #define IXP2000_GPIO_INSR IXP2000_GPIO_REG(0x38) |
| #define IXP2000_GPIO_INCR IXP2000_GPIO_REG(0x3c) |
| #define IXP2000_GPIO_INST IXP2000_GPIO_REG(0x40) |
| |
| /* |
| * "Global" registers...whatever that's supposed to mean. |
| */ |
| #define GLOBAL_REG_BASE (IXP2000_GLOBAL_REG_VIRT_BASE + 0x0a00) |
| #define GLOBAL_REG(x) (volatile unsigned long*)(GLOBAL_REG_BASE | (x)) |
| |
| #define IXP2000_MAJ_PROD_TYPE_MASK 0x001F0000 |
| #define IXP2000_MAJ_PROD_TYPE_IXP2000 0x00000000 |
| #define IXP2000_MIN_PROD_TYPE_MASK 0x0000FF00 |
| #define IXP2000_MIN_PROD_TYPE_IXP2400 0x00000200 |
| #define IXP2000_MIN_PROD_TYPE_IXP2850 0x00000100 |
| #define IXP2000_MIN_PROD_TYPE_IXP2800 0x00000000 |
| #define IXP2000_MAJ_REV_MASK 0x000000F0 |
| #define IXP2000_MIN_REV_MASK 0x0000000F |
| #define IXP2000_PROD_ID_MASK 0xFFFFFFFF |
| |
| #define IXP2000_PRODUCT_ID GLOBAL_REG(0x00) |
| #define IXP2000_MISC_CONTROL GLOBAL_REG(0x04) |
| #define IXP2000_MSF_CLK_CNTRL GLOBAL_REG(0x08) |
| #define IXP2000_RESET0 GLOBAL_REG(0x0c) |
| #define IXP2000_RESET1 GLOBAL_REG(0x10) |
| #define IXP2000_CCR GLOBAL_REG(0x14) |
| #define IXP2000_STRAP_OPTIONS GLOBAL_REG(0x18) |
| |
| #define RSTALL (1 << 16) |
| #define WDT_RESET_ENABLE 0x01000000 |
| |
| |
| /* |
| * MSF registers. The IXP2400 and IXP2800 have somewhat different MSF |
| * units, but the registers that differ between the two don't overlap, |
| * so we can have one register list for both. |
| */ |
| #define IXP2000_MSF_REG(x) ((volatile unsigned long*)(IXP2000_MSF_VIRT_BASE + (x))) |
| #define IXP2000_MSF_RX_CONTROL IXP2000_MSF_REG(0x0000) |
| #define IXP2000_MSF_TX_CONTROL IXP2000_MSF_REG(0x0004) |
| #define IXP2000_MSF_INTERRUPT_STATUS IXP2000_MSF_REG(0x0008) |
| #define IXP2000_MSF_INTERRUPT_ENABLE IXP2000_MSF_REG(0x000c) |
| #define IXP2000_MSF_CSIX_TYPE_MAP IXP2000_MSF_REG(0x0010) |
| #define IXP2000_MSF_FC_EGRESS_STATUS IXP2000_MSF_REG(0x0014) |
| #define IXP2000_MSF_FC_INGRESS_STATUS IXP2000_MSF_REG(0x0018) |
| #define IXP2000_MSF_HWM_CONTROL IXP2000_MSF_REG(0x0024) |
| #define IXP2000_MSF_FC_STATUS_OVERRIDE IXP2000_MSF_REG(0x0028) |
| #define IXP2000_MSF_CLOCK_CONTROL IXP2000_MSF_REG(0x002c) |
| #define IXP2000_MSF_RX_PORT_MAP IXP2000_MSF_REG(0x0040) |
| #define IXP2000_MSF_RBUF_ELEMENT_DONE IXP2000_MSF_REG(0x0044) |
| #define IXP2000_MSF_RX_MPHY_POLL_LIMIT IXP2000_MSF_REG(0x0048) |
| #define IXP2000_MSF_RX_CALENDAR_LENGTH IXP2000_MSF_REG(0x0048) |
| #define IXP2000_MSF_RX_THREAD_FREELIST_TIMEOUT_0 IXP2000_MSF_REG(0x0050) |
| #define IXP2000_MSF_RX_THREAD_FREELIST_TIMEOUT_1 IXP2000_MSF_REG(0x0054) |
| #define IXP2000_MSF_RX_THREAD_FREELIST_TIMEOUT_2 IXP2000_MSF_REG(0x0058) |
| #define IXP2000_MSF_TX_SEQUENCE_0 IXP2000_MSF_REG(0x0060) |
| #define IXP2000_MSF_TX_SEQUENCE_1 IXP2000_MSF_REG(0x0064) |
| #define IXP2000_MSF_TX_SEQUENCE_2 IXP2000_MSF_REG(0x0068) |
| #define IXP2000_MSF_TX_MPHY_POLL_LIMIT IXP2000_MSF_REG(0x0070) |
| #define IXP2000_MSF_TX_CALENDAR_LENGTH IXP2000_MSF_REG(0x0070) |
| #define IXP2000_MSF_RX_UP_CONTROL_0 IXP2000_MSF_REG(0x0080) |
| #define IXP2000_MSF_RX_UP_CONTROL_1 IXP2000_MSF_REG(0x0084) |
| #define IXP2000_MSF_RX_UP_CONTROL_2 IXP2000_MSF_REG(0x0088) |
| #define IXP2000_MSF_RX_UP_CONTROL_3 IXP2000_MSF_REG(0x008c) |
| #define IXP2000_MSF_TX_UP_CONTROL_0 IXP2000_MSF_REG(0x0090) |
| #define IXP2000_MSF_TX_UP_CONTROL_1 IXP2000_MSF_REG(0x0094) |
| #define IXP2000_MSF_TX_UP_CONTROL_2 IXP2000_MSF_REG(0x0098) |
| #define IXP2000_MSF_TX_UP_CONTROL_3 IXP2000_MSF_REG(0x009c) |
| #define IXP2000_MSF_TRAIN_DATA IXP2000_MSF_REG(0x00a0) |
| #define IXP2000_MSF_TRAIN_CALENDAR IXP2000_MSF_REG(0x00a4) |
| #define IXP2000_MSF_TRAIN_FLOW_CONTROL IXP2000_MSF_REG(0x00a8) |
| #define IXP2000_MSF_TX_CALENDAR_0 IXP2000_MSF_REG(0x1000) |
| #define IXP2000_MSF_RX_PORT_CALENDAR_STATUS IXP2000_MSF_REG(0x1400) |
| |
| |
| #endif /* _IXP2000_H_ */ |