/* Copyright (c) 2017-2019, The Linux Foundation. All rights reserved.
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 and
 * only version 2 as published by the Free Software Foundation.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 */

#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/spmi/spmi.h>
#include <dt-bindings/msm/power-on.h>

&spmi_bus {
	qcom,pmi632@2 {
		compatible = "qcom,spmi-pmic";
		reg = <0x2 SPMI_USID>;
		#address-cells = <1>;
		#size-cells = <1>;

		pmi632_revid: qcom,revid@100 {
			compatible = "qcom,qpnp-revid";
			reg = <0x100 0x100>;
		};

		pmi632_pon: qcom,power-on@800 {
			compatible = "qcom,qpnp-power-on";
			reg = <0x800 0x100>;

			qcom,secondary-pon-reset;
			qcom,s3-src = "kpdpwr";
		};

		pmi632_vadc: vadc@3100 {
			compatible = "qcom,qpnp-vadc-hc",
				"qcom,qpnp-adc-hc-pm5";
			reg = <0x3100 0x100>;
			#address-cells = <1>;
			#size-cells = <0>;
			interrupts = <0x2 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
			interrupt-names = "eoc-int-en-set";
			qcom,adc-vdd-reference = <1875>;
			qcom,adc-full-scale-code = <0x70e4>;
			qcom,pmic-revid = <&pmi632_revid>;

			chan@0 {
				label = "ref_gnd";
				reg = <0>;
				qcom,decimation = <2>;
				qcom,pre-div-channel-scaling = <0>;
				qcom,calibration-type = "absolute";
				qcom,scale-function = <0>;
				qcom,hw-settle-time = <0>;
				qcom,fast-avg-setup = <0>;
				qcom,cal-val = <0>;
			};

			chan@1 {
				label = "ref_1250v";
				reg = <1>;
				qcom,decimation = <2>;
				qcom,pre-div-channel-scaling = <0>;
				qcom,calibration-type = "absolute";
				qcom,scale-function = <0>;
				qcom,hw-settle-time = <0>;
				qcom,fast-avg-setup = <0>;
				qcom,cal-val = <0>;
			};

			chan@83 {
				label = "vph_pwr";
				reg = <0x83>;
				qcom,decimation = <2>;
				qcom,pre-div-channel-scaling = <1>;
				qcom,calibration-type = "absolute";
				qcom,scale-function = <0>;
				qcom,hw-settle-time = <0>;
				qcom,fast-avg-setup = <0>;
				qcom,cal-val = <0>;
			};

			chan@84 {
				label = "vbat_sns";
				reg = <0x84>;
				qcom,decimation = <2>;
				qcom,pre-div-channel-scaling = <1>;
				qcom,calibration-type = "absolute";
				qcom,scale-function = <0>;
				qcom,hw-settle-time = <0>;
				qcom,fast-avg-setup = <0>;
				qcom,cal-val = <0>;
			};

			chan@6 {
				label = "die_temp";
				reg = <6>;
				qcom,decimation = <2>;
				qcom,pre-div-channel-scaling = <0>;
				qcom,calibration-type = "absolute";
				qcom,scale-function = <19>;
				qcom,hw-settle-time = <0>;
				qcom,fast-avg-setup = <0>;
				qcom,cal-val = <0>;
			};

			chan@7 {
				label = "usb_in_i";
				reg = <7>;
				qcom,decimation = <2>;
				qcom,pre-div-channel-scaling = <0>;
				qcom,calibration-type = "absolute";
				qcom,scale-function = <21>;
				qcom,hw-settle-time = <0>;
				qcom,fast-avg-setup = <0>;
				qcom,cal-val = <0>;
			};

			chan@8 {
				label = "usb_in_v";
				reg = <8>;
				qcom,decimation = <2>;
				qcom,pre-div-channel-scaling = <8>;
				qcom,calibration-type = "absolute";
				qcom,scale-function = <0>;
				qcom,hw-settle-time = <0>;
				qcom,fast-avg-setup = <0>;
				qcom,cal-val = <0>;
			};

			chan@9 {
				label = "chg_temp";
				reg = <9>;
				qcom,decimation = <2>;
				qcom,pre-div-channel-scaling = <0>;
				qcom,calibration-type = "absolute";
				qcom,scale-function = <18>;
				qcom,hw-settle-time = <0>;
				qcom,fast-avg-setup = <0>;
				qcom,cal-val = <0>;
			};

			chan@4a {
				label = "bat_therm";
				reg = <0x4a>;
				qcom,decimation = <2>;
				qcom,pre-div-channel-scaling = <0>;
				qcom,calibration-type = "ratiometric";
				qcom,scale-function = <17>;
				qcom,hw-settle-time = <0>;
				qcom,fast-avg-setup = <0>;
				qcom,cal-val = <0>;
			};

			chan@2a {
				label = "bat_therm_PU30";
				reg = <0x2a>;
				qcom,decimation = <2>;
				qcom,pre-div-channel-scaling = <0>;
				qcom,calibration-type = "ratiometric";
				qcom,scale-function = <24>;
				qcom,hw-settle-time = <0>;
				qcom,fast-avg-setup = <0>;
				qcom,cal-val = <0>;
			};

			chan@6a {
				label = "bat_therm_PU400";
				reg = <0x6a>;
				qcom,decimation = <2>;
				qcom,pre-div-channel-scaling = <0>;
				qcom,calibration-type = "ratiometric";
				qcom,scale-function = <25>;
				qcom,hw-settle-time = <0>;
				qcom,fast-avg-setup = <0>;
				qcom,cal-val = <0>;
			};

			chan@4b {
				label = "bat_id";
				reg = <0x4b>;
				qcom,decimation = <2>;
				qcom,pre-div-channel-scaling = <0>;
				qcom,calibration-type = "ratiometric";
				qcom,scale-function = <0>;
				qcom,hw-settle-time = <0>;
				qcom,fast-avg-setup = <0>;
				qcom,cal-val = <0>;
			};

			chan@4c {
				label = "xo_therm";
				reg = <0x4c>;
				qcom,decimation = <2>;
				qcom,pre-div-channel-scaling = <0>;
				qcom,calibration-type = "ratiometric";
				qcom,scale-function = <4>;
				qcom,hw-settle-time = <8>;
				qcom,fast-avg-setup = <0>;
			};


			chan@1e {
				label = "mid_chg";
				reg = <0x1e>;
				qcom,decimation = <2>;
				qcom,pre-div-channel-scaling = <3>;
				qcom,calibration-type = "absolute";
				qcom,scale-function = <0>;
				qcom,hw-settle-time = <0>;
				qcom,fast-avg-setup = <0>;
				qcom,cal-val = <0>;
			};

			chan@52 {
				label = "typec_therm";
				reg = <0x52>;
				qcom,decimation = <2>;
				qcom,pre-div-channel-scaling = <0>;
				qcom,calibration-type = "ratiometric";
				qcom,scale-function = <2>;
				qcom,hw-settle-time = <0>;
				qcom,fast-avg-setup = <0>;
				qcom,cal-val = <0>;
			};

			chan@53 {
				label = "quiet_therm";
				reg = <0x53>;
				qcom,decimation = <2>;
				qcom,pre-div-channel-scaling = <0>;
				qcom,calibration-type = "ratiometric";
				qcom,scale-function = <2>;
				qcom,hw-settle-time = <0>;
				qcom,fast-avg-setup = <0>;
				qcom,cal-val = <0>;
			};

			chan@54 {
				label = "smb_therm";
				reg = <0x54>;
				qcom,decimation = <2>;
				qcom,pre-div-channel-scaling = <0>;
				qcom,calibration-type = "ratiometric";
				qcom,scale-function = <2>;
				qcom,hw-settle-time = <0>;
				qcom,fast-avg-setup = <0>;
				qcom,cal-val = <0>;
			};
		};

		pmi632_adc_tm: vadc@3500 {
			compatible = "qcom,qpnp-adc-tm-hc",
				"qcom,qpnp-adc-tm-hc-pm5";
			reg = <0x3500 0x100>;
			#address-cells = <1>;
			#size-cells = <0>;
			interrupts = <0x2 0x35 0x0 IRQ_TYPE_EDGE_RISING>;
			interrupt-names = "eoc-int-en-set";
			qcom,adc-vdd-reference = <1875>;
			qcom,adc-full-scale-code = <0x70e4>;
			qcom,adc_tm-vadc = <&pmi632_vadc>;
			qcom,decimation = <0>;
			qcom,fast-avg-setup = <0>;
			#thermal-sensor-cells = <1>;

			chan@53 {
				label = "quiet_therm";
				reg = <0x53>;
				qcom,pre-div-channel-scaling = <0>;
				qcom,calibration-type = "ratiometric";
				qcom,scale-function = <2>;
				qcom,hw-settle-time = <0>;
				qcom,btm-channel-number = <0x60>;
				qcom,thermal-node;
			};

		};

		pmi632_tz: qcom,temp-alarm@2400 {
			compatible = "qcom,qpnp-temp-alarm";
			reg = <0x2400 0x100>;
			interrupts = <0x2 0x24 0x0 IRQ_TYPE_EDGE_RISING>;
			label = "pmi632_tz";
			#thermal-sensor-cells = <0>;
		};

		pmi632_gpios: pinctrl@c000 {
			compatible = "qcom,spmi-gpio";
			reg = <0xc000 0x800>;
			interrupts = <0x2 0xc0 0 IRQ_TYPE_NONE>,
					<0x2 0xc1 0 IRQ_TYPE_NONE>,
					<0x2 0xc2 0 IRQ_TYPE_NONE>,
					<0x2 0xc3 0 IRQ_TYPE_NONE>,
					<0x2 0xc4 0 IRQ_TYPE_NONE>,
					<0x2 0xc5 0 IRQ_TYPE_NONE>,
					<0x2 0xc6 0 IRQ_TYPE_NONE>,
					<0x2 0xc7 0 IRQ_TYPE_NONE>;
			interrupt-names = "pmi632_gpio1", "pmi632_gpio2",
					"pmi632_gpio3", "pmi632_gpio4",
					"pmi632_gpio5", "pmi632_gpio6",
					"pmi632_gpio7", "pmi632_gpio8";
			gpio-controller;
			#gpio-cells = <2>;
		};

		pmi632_charger: qcom,qpnp-smb5 {
			compatible = "qcom,qpnp-smb5";
			#address-cells = <1>;
			#size-cells = <1>;
			#cooling-cells = <2>;

			qcom,pmic-revid = <&pmi632_revid>;
			dpdm-supply = <&qusb_phy>;
//<2020/04/24-JessicaTseng, Re-charge condition for battery to 4.3V
			qcom,auto-recharge-vbat-mv = <4300>;
			//qcom,auto-recharge-soc = <98>;
//>2020/04/24-JessicaTseng
			qcom,chg-vadc = <&pmi632_vadc>;
			qcom,flash-disable-soc = <10>;
			qcom,sw-jeita-enable;
			qcom,step-charging-enable;
			qcom,hw-die-temp-mitigation;
			qcom,hw-connector-mitigation;
			qcom,connector-internal-pull-kohm = <100>;

//<2020/04/28-JessicaTseng, Add condition of charging current for thermal-mitigation
			qcom,thermal-mitigation
				= <2000000 1500000 1000000 500000
					500000 500000>;
//>2020/04/28-JessicaTseng

//<2020/06/04-JessicaTseng, modify charging termination current
			qcom,chg-term-src = <1>;
			qcom,chg-term-current-ma = <(-100)>;
//>2020/06/04-JessicaTseng

			qcom,chgr@1000 {
				reg = <0x1000 0x100>;
				interrupts =
					<0x2 0x10 0x0 IRQ_TYPE_EDGE_RISING>,
					<0x2 0x10 0x1 IRQ_TYPE_EDGE_RISING>,
					<0x2 0x10 0x2 IRQ_TYPE_EDGE_RISING>,
					<0x2 0x10 0x3 IRQ_TYPE_EDGE_RISING>,
					<0x2 0x10 0x4 IRQ_TYPE_EDGE_RISING>,
					<0x2 0x10 0x5 IRQ_TYPE_EDGE_RISING>,
					<0x2 0x10 0x6 IRQ_TYPE_EDGE_RISING>,
					<0x2 0x10 0x7 IRQ_TYPE_EDGE_RISING>;

				interrupt-names = "chgr-error",
						  "chg-state-change",
						  "step-chg-state-change",
						  "step-chg-soc-update-fail",
						  "step-chg-soc-update-req",
						  "fg-fvcal-qualified",
						  "vph-alarm",
						  "vph-drop-prechg";
			};

			qcom,dcdc@1100 {
				reg = <0x1100 0x100>;
				interrupts =
					<0x2 0x11 0x0 IRQ_TYPE_EDGE_RISING>,
					<0x2 0x11 0x1 IRQ_TYPE_EDGE_RISING>,
					<0x2 0x11 0x2 IRQ_TYPE_EDGE_RISING>,
					<0x2 0x11 0x3 IRQ_TYPE_EDGE_BOTH>,
					<0x2 0x11 0x4 IRQ_TYPE_EDGE_BOTH>,
					<0x2 0x11 0x5 IRQ_TYPE_EDGE_BOTH>,
					<0x2 0x11 0x6 IRQ_TYPE_EDGE_RISING>,
					<0x2 0x11 0x7 IRQ_TYPE_EDGE_BOTH>;

				interrupt-names = "otg-fail",
						  "otg-oc-disable-sw",
						  "otg-oc-hiccup",
						  "bsm-active",
						  "high-duty-cycle",
						  "input-current-limiting",
						  "concurrent-mode-disable",
						  "switcher-power-ok";
			};

			qcom,batif@1200 {
				reg = <0x1200 0x100>;
				interrupts =
					<0x2 0x12 0x0 IRQ_TYPE_EDGE_RISING>,
					<0x2 0x12 0x1 IRQ_TYPE_EDGE_RISING>,
					<0x2 0x12 0x2 IRQ_TYPE_EDGE_BOTH>,
					<0x2 0x12 0x3 IRQ_TYPE_EDGE_BOTH>,
					<0x2 0x12 0x4 IRQ_TYPE_EDGE_BOTH>,
					<0x2 0x12 0x5 IRQ_TYPE_EDGE_BOTH>,
					<0x2 0x12 0x6 IRQ_TYPE_EDGE_BOTH>,
					<0x2 0x12 0x7 IRQ_TYPE_EDGE_BOTH>;

				interrupt-names = "bat-temp",
						  "all-chnl-conv-done",
						  "bat-ov",
						  "bat-low",
						  "bat-therm-or-id-missing",
						  "bat-terminal-missing",
						  "buck-oc",
						  "vph-ov";
			};

			qcom,usb@1300 {
				reg = <0x1300 0x100>;
				interrupts =
					<0x2 0x13 0x0 IRQ_TYPE_EDGE_BOTH>,
					<0x2 0x13 0x1 IRQ_TYPE_EDGE_BOTH>,
					<0x2 0x13 0x2 IRQ_TYPE_EDGE_RISING>,
					<0x2 0x13 0x3 IRQ_TYPE_EDGE_BOTH>,
					<0x2 0x13 0x4 IRQ_TYPE_EDGE_BOTH>,
					<0x2 0x13 0x5 IRQ_TYPE_EDGE_BOTH>,
					<0x2 0x13 0x6 IRQ_TYPE_EDGE_RISING>,
					<0x2 0x13 0x7 IRQ_TYPE_EDGE_RISING>;

				interrupt-names = "usbin-collapse",
						  "usbin-vashdn",
						  "usbin-uv",
						  "usbin-ov",
						  "usbin-plugin",
						  "usbin-revi-change",
						  "usbin-src-change",
						  "usbin-icl-change";
			};

			qcom,typec@1500 {
				reg = <0x1500 0x100>;
				interrupts =
					<0x2 0x15 0x0 IRQ_TYPE_EDGE_BOTH>,
					<0x2 0x15 0x1 IRQ_TYPE_EDGE_BOTH>,
					<0x2 0x15 0x2 IRQ_TYPE_EDGE_RISING>,
					<0x2 0x15 0x3 IRQ_TYPE_EDGE_RISING>,
					<0x2 0x15 0x4 IRQ_TYPE_EDGE_BOTH>,
					<0x2 0x15 0x5 IRQ_TYPE_EDGE_RISING>,
					<0x2 0x15 0x6 IRQ_TYPE_EDGE_RISING>,
					<0x2 0x15 0x7 IRQ_TYPE_EDGE_RISING>;

				interrupt-names = "typec-or-rid-detect-change",
						  "typec-vpd-detect",
						  "typec-cc-state-change",
						  "typec-vconn-oc",
						  "typec-vbus-change",
						  "typec-attach-detach",
						  "typec-legacy-cable-detect",
						  "typec-try-snk-src-detect";
			};

			qcom,misc@1600 {
				reg = <0x1600 0x100>;
				interrupts =
					<0x2 0x16 0x0 IRQ_TYPE_EDGE_RISING>,
					<0x2 0x16 0x1 IRQ_TYPE_EDGE_RISING>,
					<0x2 0x16 0x2 IRQ_TYPE_EDGE_RISING>,
					<0x2 0x16 0x3 IRQ_TYPE_EDGE_RISING>,
					<0x2 0x16 0x4 IRQ_TYPE_EDGE_BOTH>,
					<0x2 0x16 0x5 IRQ_TYPE_EDGE_RISING>,
					<0x2 0x16 0x6 IRQ_TYPE_EDGE_RISING>,
					<0x2 0x16 0x7 IRQ_TYPE_EDGE_RISING>;

				interrupt-names = "wdog-snarl",
						  "wdog-bark",
						  "aicl-fail",
						  "aicl-done",
						  "smb-en",
						  "imp-trigger",
						  "temp-change",
						  "temp-change-smb";
			};

			qcom,schgm-flash@a600 {
				reg = <0xa600 0x100>;
				interrupts =
					<0x2 0xa6 0x2 IRQ_TYPE_EDGE_RISING>,
					<0x2 0xa6 0x5 IRQ_TYPE_EDGE_RISING>,
					<0x2 0xa6 0x6 IRQ_TYPE_EDGE_RISING>,
					<0x2 0xa6 0x7 IRQ_TYPE_EDGE_BOTH>;

				interrupt-names = "flash-state-change",
						"ilim1-s1",
						"ilim2-s2",
						"vreg-ok";
			};

			smb5_vbus: qcom,smb5-vbus {
				regulator-name = "smb5-vbus";
			};
		};

		pmi632_qg: qpnp,qg {
			compatible = "qcom,qpnp-qg";
			#address-cells = <1>;
			#size-cells = <1>;

//<2020/06/04-JessicaTseng, modify charging termination current
			//qcom,qg-iterm-ma = <100>;
			qcom,qg-iterm-ma = <150>;
//>2020/06/04-JessicaTseng

//<2020/04/24-JessicaTseng, Re-charge condition for battery to 4.3V
			//qcom,hold-soc-while-full;
			//qcom,linearize-soc;
//>2020/04/24-JessicaTseng
			qcom,qg-vadc = <&pmi632_vadc>;
			qcom,pmic-revid = <&pmi632_revid>;

			qcom,qgauge@4800 {
				status = "okay";
				reg = <0x4800 0x100>;
				interrupts =
					<0x2 0x48 0x0 IRQ_TYPE_EDGE_BOTH>,
					<0x2 0x48 0x1 IRQ_TYPE_EDGE_BOTH>,
					<0x2 0x48 0x2 IRQ_TYPE_EDGE_RISING>,
					<0x2 0x48 0x3 IRQ_TYPE_EDGE_RISING>,
					<0x2 0x48 0x4 IRQ_TYPE_EDGE_RISING>;
				interrupt-names = "qg-batt-missing",
						  "qg-vbat-low",
						  "qg-vbat-empty",
						  "qg-fifo-done",
						  "qg-good-ocv";
			};

			qcom,qg-sdam@b100 {
				status = "okay";
				reg = <0xb100 0x100>;
			};
		};

		bcl_sensor: bcl@3d00 {
			compatible = "qcom,bcl-v5";
			reg = <0x3d00 0x100>;
			interrupts = <0x2 0x3d 0x0 IRQ_TYPE_NONE>,
					<0x2 0x3d 0x1 IRQ_TYPE_NONE>,
					<0x2 0x3d 0x0 IRQ_TYPE_NONE>,
					<0x2 0x3d 0x1 IRQ_TYPE_NONE>,
					<0x2 0x3d 0x2 IRQ_TYPE_NONE>;
			interrupt-names = "bcl-ibat-lvl0",
						"bcl-ibat-lvl1",
						"bcl-vbat-lvl0",
						"bcl-vbat-lvl1",
						"bcl-vbat-lvl2";
			#thermal-sensor-cells = <1>;
		};

		bcl_soc: bcl-soc {
			compatible = "qcom,msm-bcl-soc";
			#thermal-sensor-cells = <0>;
		};

		pmi632_pbs_client3: qcom,pbs@7400 {
			compatible = "qcom,qpnp-pbs";
			reg = <0x7400 0x100>;
		};

		pmi632_sdam7: qcom,sdam@b600 {
			compatible = "qcom,spmi-sdam";
			reg = <0xb600 0x100>;
		};
	};

	pmi632_3: qcom,pmi632@3 {
		compatible ="qcom,spmi-pmic";
		reg = <0x3 SPMI_USID>;
		#address-cells = <1>;
		#size-cells = <1>;

		pmi632_vib: qcom,vibrator@5700 {
			compatible = "qcom,qpnp-vibrator-ldo";
			reg = <0x5700 0x100>;
			qcom,vib-ldo-volt-uv = <3000000>;
			qcom,disable-overdrive;
		};

		pmi632_pwm: qcom,pwms@b300 {
			compatible = "qcom,pwm-lpg";
			reg = <0xb300 0x500>;
			reg-names = "lpg-base";
			#pwm-cells = <2>;
			nvmem-names = "ppg_sdam";
			nvmem = <&pmi632_sdam7>;
			qcom,pbs-client = <&pmi632_pbs_client3>;
			qcom,lut-sdam-base = <0x80>;
		//<2020/04/21-Yuting Shih.[FAIRPHONE-Q][MISC][COMMON][LED][][]Modified for breath ramp and timing.
		#if 1
			qcom,lut-patterns = <0 0 0 0 0 0 0 0 2 16 30 44 58 72 86 96 100 100
						100 100 96 86 72 58 44 30 16 2 0 0 0 0 0 0 0 0>;
		#else
			/* Code default */
			qcom,lut-patterns = <0 0 0 14 28 42 56 70 84 100
						100 84 70 56 42 28 14 0 0 0>;
		#endif
		//>2020/04/21-Yuting Shih.[FAIRPHONE-Q][MISC][COMMON][LED][][].
			lpg@1 {
				qcom,lpg-chan-id = <1>;
		//<2020/04/21-Yuting Shih.[FAIRPHONE-Q][MISC][COMMON][LED][][]Modified for breath ramp and timing.
		#if 1
				qcom,ramp-step-ms = <60>;
				qcom,ramp-pause-hi-count = <80>;
				qcom,ramp-pause-lo-count = <80>;
				qcom,ramp-low-index = <0>;
				qcom,ramp-high-index = <35>;
				//qcom,ramp-toggle; /* ramp from high to low */
				//qcom,ramp-from-low-to-high;
				qcom,ramp-pattern-repeat;
		#else
			/* Code default */
				qcom,ramp-step-ms = <200>;
				qcom,ramp-low-index = <0>;
				qcom,ramp-high-index = <19>;
				qcom,ramp-pattern-repeat;
		#endif
		//>2020/04/21-Yuting Shih.[FAIRPHONE-Q][MISC][COMMON][LED][][].
				qcom,lpg-sdam-base = <0x48>;
			};
			lpg@2 {
				qcom,lpg-chan-id = <2>;
		//<2020/04/21-Yuting Shih.[FAIRPHONE-Q][MISC][COMMON][LED][][]Modified for breath ramp and timing.
		#if 1
				qcom,ramp-step-ms = <60>;
				qcom,ramp-pause-hi-count = <80>;
				qcom,ramp-pause-lo-count = <80>;
				qcom,ramp-low-index = <0>;
				qcom,ramp-high-index = <35>;
				//qcom,ramp-toggle; /* ramp from high to low */
				//qcom,ramp-from-low-to-high;
				qcom,ramp-pattern-repeat;
		#else
			/* Code default */
				qcom,ramp-step-ms = <200>;
				qcom,ramp-low-index = <0>;
				qcom,ramp-high-index = <19>;
				qcom,ramp-pattern-repeat;
		#endif
		//>2020/04/21-Yuting Shih.[FAIRPHONE-Q][MISC][COMMON][LED][][].
				qcom,lpg-sdam-base = <0x56>;
			};
			lpg@3 {
				qcom,lpg-chan-id = <3>;
		//<2020/04/21-Yuting Shih.[FAIRPHONE-Q][MISC][COMMON][LED][][]Modified for breath ramp and timing.
		#if 1
				qcom,ramp-step-ms = <60>;
				qcom,ramp-pause-hi-count = <80>;
				qcom,ramp-pause-lo-count = <80>;
				qcom,ramp-low-index = <0>;
				qcom,ramp-high-index = <35>;
				//qcom,ramp-toggle; /* ramp from high to low */
				//qcom,ramp-from-low-to-high;
				qcom,ramp-pattern-repeat;
		#else
			/* Code default */
				qcom,ramp-step-ms = <200>;
				qcom,ramp-low-index = <0>;
				qcom,ramp-high-index = <19>;
				qcom,ramp-pattern-repeat;
		#endif
		//>2020/04/21-Yuting Shih.[FAIRPHONE-Q][MISC][COMMON][LED][][].
				qcom,lpg-sdam-base = <0x64>;
			};
		};

		pmi632_rgb: qcom,leds@d000 {
			compatible = "qcom,tri-led";
			reg = <0xd000 0x100>;
			red {
				label = "red";
				pwms = <&pmi632_pwm 0 1000000>;
				led-sources = <0>;
				linux,default-trigger = "timer";
			};
			green {
				label = "green";
				pwms = <&pmi632_pwm 1 1000000>;
				led-sources = <1>;
				linux,default-trigger = "timer";
			};
			blue {
				label = "blue";
				pwms = <&pmi632_pwm 2 1000000>;
				led-sources = <2>;
				linux,default-trigger = "timer";
			};
		};

		pmi632_lcdb: qpnp-lcdb@ec00 {
			compatible = "qcom,qpnp-lcdb-regulator";
			#address-cells = <1>;
			#size-cells = <1>;
			reg = <0xec00 0x100>;
			interrupts = <0x3 0xec 0x1 IRQ_TYPE_EDGE_RISING>;
			interrupt-names = "sc-irq";

			qcom,pmic-revid = <&pmi632_revid>;
			qcom,voltage-step-ramp;

			lcdb_ldo_vreg: ldo {
				label = "ldo";
				regulator-name = "lcdb_ldo";
				regulator-min-microvolt = <4000000>;
				regulator-max-microvolt = <6000000>;
			};

			lcdb_ncp_vreg: ncp {
				label = "ncp";
				regulator-name = "lcdb_ncp";
				regulator-min-microvolt = <4000000>;
				regulator-max-microvolt = <6000000>;
			};

			lcdb_bst_vreg: bst {
				label = "bst";
				regulator-name = "lcdb_bst";
				regulator-min-microvolt = <4700000>;
				regulator-max-microvolt = <6275000>;
			};
		};

		flash_led: qcom,leds@d300 {
			compatible = "qcom,qpnp-flash-led-v2";
			status = "okay";
			reg = <0xd300 0x100>;
			label = "flash";
			interrupts = <0x3 0xd3 0x0 IRQ_TYPE_EDGE_RISING>,
				     <0x3 0xd3 0x3 IRQ_TYPE_EDGE_RISING>,
				     <0x3 0xd3 0x4 IRQ_TYPE_EDGE_RISING>;
			interrupt-names = "led-fault-irq",
					  "all-ramp-down-done-irq",
					  "all-ramp-up-done-irq";
			qcom,short-circuit-det;
			qcom,open-circuit-det;
			qcom,vph-droop-det;
			qcom,thermal-derate-en;
			qcom,thermal-derate-current = <200 500 1000>;
			qcom,isc-delay = <192>;
			qcom,pmic-revid = <&pmi632_revid>;

			pmi632_flash0: qcom,flash_0 {
				label = "flash";
				qcom,led-name = "led:flash_0";
				qcom,max-current = <1500>;
				qcom,default-led-trigger = "flash0_trigger";
				qcom,id = <0>;
				qcom,current-ma = <1000>;
				qcom,duration-ms = <1280>;
				qcom,ires-ua = <12500>;
				qcom,hdrm-voltage-mv = <400>;
				qcom,hdrm-vol-hi-lo-win-mv = <100>;
			};

			pmi632_flash1: qcom,flash_1 {
				label = "flash";
				qcom,led-name = "led:flash_1";
				qcom,max-current = <1500>;
				qcom,default-led-trigger = "flash1_trigger";
				qcom,id = <1>;
				qcom,current-ma = <1000>;
				qcom,duration-ms = <1280>;
				qcom,ires-ua = <12500>;
				qcom,hdrm-voltage-mv = <400>;
				qcom,hdrm-vol-hi-lo-win-mv = <100>;
			};

			pmi632_torch0: qcom,torch_0 {
				label = "torch";
				qcom,led-name = "led:torch_0";
				qcom,max-current = <500>;
				qcom,default-led-trigger = "torch0_trigger";
				qcom,id = <0>;
				qcom,current-ma = <300>;
				qcom,ires-ua = <12500>;
				qcom,hdrm-voltage-mv = <400>;
				qcom,hdrm-vol-hi-lo-win-mv = <100>;
			};

			pmi632_torch1: qcom,torch_1 {
				label = "torch";
				qcom,led-name = "led:torch_1";
				qcom,max-current = <500>;
				qcom,default-led-trigger = "torch1_trigger";
				qcom,id = <1>;
				qcom,current-ma = <300>;
				qcom,ires-ua = <12500>;
				qcom,hdrm-voltage-mv = <400>;
				qcom,hdrm-vol-hi-lo-win-mv = <100>;
			};

			pmi632_switch0: qcom,led_switch_0 {
				label = "switch";
				qcom,led-name = "led:switch_0";
				qcom,led-mask = <3>;
				qcom,default-led-trigger = "switch0_trigger";
			};

			pmi632_switch1: qcom,led_switch_1 {
				label = "switch";
				qcom,led-name = "led:switch_1";
				qcom,led-mask = <2>;
				qcom,default-led-trigger = "switch1_trigger";
			};

		};

	};
};
&soc {
	led_flash0: qcom,camera-flash {
		cell-index = <0>;
		compatible = "qcom,camera-flash";
		qcom,flash-type = <1>;
		qcom,flash-source = <&pmi632_flash0 &pmi632_flash1>;
		qcom,torch-source = <&pmi632_torch0 &pmi632_torch1>;
		qcom,switch-source = <&pmi632_switch0>;
	};
};

&thermal_zones {
	pmi-ibat-lvl0 {
		polling-delay-passive = <100>;
		polling-delay = <0>;
		thermal-governor = "step_wise";
		thermal-sensors = <&bcl_sensor 0>;
		wake-capable-sensor;

		trips {
			pmi632_ibat_lvl0: ibat-lvl0 {
				temperature = <4000>;
				hysteresis = <200>;
				type = "passive";
			};
		};
	};

	pmi-ibat-lvl1 {
		polling-delay-passive = <0>;
		polling-delay = <0>;
		thermal-governor = "step_wise";
		thermal-sensors = <&bcl_sensor 1>;
		wake-capable-sensor;

		trips {
			ibat-lvl1 {
				temperature = <4200>;
				hysteresis = <200>;
				type = "passive";
			};
		};
	};

	pmi-vbat-lvl0 {
		polling-delay-passive = <100>;
		polling-delay = <0>;
		thermal-governor = "low_limits_cap";
		thermal-sensors = <&bcl_sensor 2>;
		wake-capable-sensor;
		tracks-low;

		trips {
			pmi632_vbat_lvl0: vbat-lvl0 {
				temperature = <3000>;
				hysteresis = <100>;
				type = "passive";
			};
		};
	};

	pmi-vbat-lvl1 {
		polling-delay-passive = <0>;
		polling-delay = <0>;
		thermal-governor = "low_limits_cap";
		thermal-sensors = <&bcl_sensor 3>;
		wake-capable-sensor;
		tracks-low;

		trips {
			vbat-lvl1 {
				temperature = <2800>;
				hysteresis = <100>;
				type = "passive";
			};
		};
	};

	pmi-vbat-lvl2 {
		polling-delay-passive = <0>;
		polling-delay = <0>;
		thermal-governor = "low_limits_cap";
		thermal-sensors = <&bcl_sensor 4>;
		wake-capable-sensor;
		tracks-low;

		trips {
			vbat-lvl1 {
				temperature = <2600>;
				hysteresis = <100>;
				type = "passive";
			};
		};
	};

	soc {
		polling-delay-passive = <100>;
		polling-delay = <0>;
		thermal-governor = "low_limits_cap";
		thermal-sensors = <&bcl_soc>;
		wake-capable-sensor;
		tracks-low;

		trips {
			pmi632_low_soc: low-soc {
				temperature = <10>;
				hysteresis = <0>;
				type = "passive";
			};
		};
	};

	pmi632_tz {
		polling-delay-passive = <0>;
		polling-delay = <0>;
		thermal-governor = "step_wise";
		thermal-sensors = <&pmi632_tz>;
		wake-capable-sensor;

		trips {
			pmi632_tz_trip0: pmi632-trip0 {
				temperature = <105000>;
				hysteresis = <0>;
				type = "passive";
			};
			pmi632_tz_trip1: pmi632-trip1 {
				temperature = <125000>;
				hysteresis = <0>;
				type = "passive";
			};
			pmi632_tz_trip2: pmi632-trip2 {
				temperature = <145000>;
				hysteresis = <0>;
				type = "passive";
			};
		};
	};
};