Merge branch for-rmk-devel of git://aeryn.fluff.org.uk/bjdooks/linux into devel
diff --git a/Documentation/arm/Samsung-S3C24XX/GPIO.txt b/Documentation/arm/Samsung-S3C24XX/GPIO.txt
index ea7ccfc..948c871 100644
--- a/Documentation/arm/Samsung-S3C24XX/GPIO.txt
+++ b/Documentation/arm/Samsung-S3C24XX/GPIO.txt
@@ -51,7 +51,7 @@
-----------
Each pin has an unique number associated with it in regs-gpio.h,
- eg S3C2410_GPA0 or S3C2410_GPF1. These defines are used to tell
+ eg S3C2410_GPA(0) or S3C2410_GPF(1). These defines are used to tell
the GPIO functions which pin is to be used.
@@ -65,11 +65,11 @@
Eg:
- s3c2410_gpio_cfgpin(S3C2410_GPA0, S3C2410_GPA0_ADDR0);
- s3c2410_gpio_cfgpin(S3C2410_GPE8, S3C2410_GPE8_SDDAT1);
+ s3c2410_gpio_cfgpin(S3C2410_GPA(0), S3C2410_GPA0_ADDR0);
+ s3c2410_gpio_cfgpin(S3C2410_GPE(8), S3C2410_GPE8_SDDAT1);
- which would turn GPA0 into the lowest Address line A0, and set
- GPE8 to be connected to the SDIO/MMC controller's SDDAT1 line.
+ which would turn GPA(0) into the lowest Address line A0, and set
+ GPE(8) to be connected to the SDIO/MMC controller's SDDAT1 line.
Reading the current configuration
diff --git a/arch/arm/common/Kconfig b/arch/arm/common/Kconfig
index a2cd9be..38518d4 100644
--- a/arch/arm/common/Kconfig
+++ b/arch/arm/common/Kconfig
@@ -4,6 +4,13 @@
config ARM_VIC
bool
+config ARM_VIC_NR
+ int
+ default 2
+ help
+ The maximum number of VICs available in the system, for
+ power management.
+
config ICST525
bool
diff --git a/arch/arm/common/vic.c b/arch/arm/common/vic.c
index b2a781d..887c6eb 100644
--- a/arch/arm/common/vic.c
+++ b/arch/arm/common/vic.c
@@ -21,6 +21,7 @@
#include <linux/init.h>
#include <linux/list.h>
#include <linux/io.h>
+#include <linux/sysdev.h>
#include <asm/mach/irq.h>
#include <asm/hardware/vic.h>
@@ -39,11 +40,219 @@
writel(1 << irq, base + VIC_INT_ENABLE);
}
+/**
+ * vic_init2 - common initialisation code
+ * @base: Base of the VIC.
+ *
+ * Common initialisation code for registeration
+ * and resume.
+*/
+static void vic_init2(void __iomem *base)
+{
+ int i;
+
+ for (i = 0; i < 16; i++) {
+ void __iomem *reg = base + VIC_VECT_CNTL0 + (i * 4);
+ writel(VIC_VECT_CNTL_ENABLE | i, reg);
+ }
+
+ writel(32, base + VIC_PL190_DEF_VECT_ADDR);
+}
+
+#if defined(CONFIG_PM)
+/**
+ * struct vic_device - VIC PM device
+ * @sysdev: The system device which is registered.
+ * @irq: The IRQ number for the base of the VIC.
+ * @base: The register base for the VIC.
+ * @resume_sources: A bitmask of interrupts for resume.
+ * @resume_irqs: The IRQs enabled for resume.
+ * @int_select: Save for VIC_INT_SELECT.
+ * @int_enable: Save for VIC_INT_ENABLE.
+ * @soft_int: Save for VIC_INT_SOFT.
+ * @protect: Save for VIC_PROTECT.
+ */
+struct vic_device {
+ struct sys_device sysdev;
+
+ void __iomem *base;
+ int irq;
+ u32 resume_sources;
+ u32 resume_irqs;
+ u32 int_select;
+ u32 int_enable;
+ u32 soft_int;
+ u32 protect;
+};
+
+/* we cannot allocate memory when VICs are initially registered */
+static struct vic_device vic_devices[CONFIG_ARM_VIC_NR];
+
+static inline struct vic_device *to_vic(struct sys_device *sys)
+{
+ return container_of(sys, struct vic_device, sysdev);
+}
+
+static int vic_id;
+
+static int vic_class_resume(struct sys_device *dev)
+{
+ struct vic_device *vic = to_vic(dev);
+ void __iomem *base = vic->base;
+
+ printk(KERN_DEBUG "%s: resuming vic at %p\n", __func__, base);
+
+ /* re-initialise static settings */
+ vic_init2(base);
+
+ writel(vic->int_select, base + VIC_INT_SELECT);
+ writel(vic->protect, base + VIC_PROTECT);
+
+ /* set the enabled ints and then clear the non-enabled */
+ writel(vic->int_enable, base + VIC_INT_ENABLE);
+ writel(~vic->int_enable, base + VIC_INT_ENABLE_CLEAR);
+
+ /* and the same for the soft-int register */
+
+ writel(vic->soft_int, base + VIC_INT_SOFT);
+ writel(~vic->soft_int, base + VIC_INT_SOFT_CLEAR);
+
+ return 0;
+}
+
+static int vic_class_suspend(struct sys_device *dev, pm_message_t state)
+{
+ struct vic_device *vic = to_vic(dev);
+ void __iomem *base = vic->base;
+
+ printk(KERN_DEBUG "%s: suspending vic at %p\n", __func__, base);
+
+ vic->int_select = readl(base + VIC_INT_SELECT);
+ vic->int_enable = readl(base + VIC_INT_ENABLE);
+ vic->soft_int = readl(base + VIC_INT_SOFT);
+ vic->protect = readl(base + VIC_PROTECT);
+
+ /* set the interrupts (if any) that are used for
+ * resuming the system */
+
+ writel(vic->resume_irqs, base + VIC_INT_ENABLE);
+ writel(~vic->resume_irqs, base + VIC_INT_ENABLE_CLEAR);
+
+ return 0;
+}
+
+struct sysdev_class vic_class = {
+ .name = "vic",
+ .suspend = vic_class_suspend,
+ .resume = vic_class_resume,
+};
+
+/**
+ * vic_pm_register - Register a VIC for later power management control
+ * @base: The base address of the VIC.
+ * @irq: The base IRQ for the VIC.
+ * @resume_sources: bitmask of interrupts allowed for resume sources.
+ *
+ * Register the VIC with the system device tree so that it can be notified
+ * of suspend and resume requests and ensure that the correct actions are
+ * taken to re-instate the settings on resume.
+ */
+static void __init vic_pm_register(void __iomem *base, unsigned int irq, u32 resume_sources)
+{
+ struct vic_device *v;
+
+ if (vic_id >= ARRAY_SIZE(vic_devices))
+ printk(KERN_ERR "%s: too few VICs, increase CONFIG_ARM_VIC_NR\n", __func__);
+ else {
+ v = &vic_devices[vic_id];
+ v->base = base;
+ v->resume_sources = resume_sources;
+ v->irq = irq;
+ vic_id++;
+ }
+}
+
+/**
+ * vic_pm_init - initicall to register VIC pm
+ *
+ * This is called via late_initcall() to register
+ * the resources for the VICs due to the early
+ * nature of the VIC's registration.
+*/
+static int __init vic_pm_init(void)
+{
+ struct vic_device *dev = vic_devices;
+ int err;
+ int id;
+
+ if (vic_id == 0)
+ return 0;
+
+ err = sysdev_class_register(&vic_class);
+ if (err) {
+ printk(KERN_ERR "%s: cannot register class\n", __func__);
+ return err;
+ }
+
+ for (id = 0; id < vic_id; id++, dev++) {
+ dev->sysdev.id = id;
+ dev->sysdev.cls = &vic_class;
+
+ err = sysdev_register(&dev->sysdev);
+ if (err) {
+ printk(KERN_ERR "%s: failed to register device\n",
+ __func__);
+ return err;
+ }
+ }
+
+ return 0;
+}
+
+late_initcall(vic_pm_init);
+
+static struct vic_device *vic_from_irq(unsigned int irq)
+{
+ struct vic_device *v = vic_devices;
+ unsigned int base_irq = irq & ~31;
+ int id;
+
+ for (id = 0; id < vic_id; id++, v++) {
+ if (v->irq == base_irq)
+ return v;
+ }
+
+ return NULL;
+}
+
+static int vic_set_wake(unsigned int irq, unsigned int on)
+{
+ struct vic_device *v = vic_from_irq(irq);
+ unsigned int off = irq & 31;
+
+ if (!v)
+ return -EINVAL;
+
+ if (on)
+ v->resume_irqs |= 1 << off;
+ else
+ v->resume_irqs &= ~(1 << off);
+
+ return 0;
+}
+
+#else
+static inline void vic_pm_register(void __iomem *base, unsigned int irq, u32 arg1) { }
+
+#define vic_set_wake NULL
+#endif /* CONFIG_PM */
+
static struct irq_chip vic_chip = {
.name = "VIC",
.ack = vic_mask_irq,
.mask = vic_mask_irq,
.unmask = vic_unmask_irq,
+ .set_wake = vic_set_wake,
};
/**
@@ -51,9 +260,10 @@
* @base: iomem base address
* @irq_start: starting interrupt number, must be muliple of 32
* @vic_sources: bitmask of interrupt sources to allow
+ * @resume_sources: bitmask of interrupt sources to allow for resume
*/
void __init vic_init(void __iomem *base, unsigned int irq_start,
- u32 vic_sources)
+ u32 vic_sources, u32 resume_sources)
{
unsigned int i;
@@ -77,12 +287,7 @@
writel(value, base + VIC_PL190_VECT_ADDR);
}
- for (i = 0; i < 16; i++) {
- void __iomem *reg = base + VIC_VECT_CNTL0 + (i * 4);
- writel(VIC_VECT_CNTL_ENABLE | i, reg);
- }
-
- writel(32, base + VIC_PL190_DEF_VECT_ADDR);
+ vic_init2(base);
for (i = 0; i < 32; i++) {
if (vic_sources & (1 << i)) {
@@ -94,4 +299,6 @@
set_irq_flags(irq, IRQF_VALID | IRQF_PROBE);
}
}
+
+ vic_pm_register(base, irq_start, resume_sources);
}
diff --git a/arch/arm/include/asm/hardware/pl080.h b/arch/arm/include/asm/hardware/pl080.h
new file mode 100644
index 0000000..6a6c66b
--- /dev/null
+++ b/arch/arm/include/asm/hardware/pl080.h
@@ -0,0 +1,138 @@
+/* arch/arm/include/asm/hardware/pl080.h
+ *
+ * Copyright 2008 Openmoko, Inc.
+ * Copyright 2008 Simtec Electronics
+ * http://armlinux.simtec.co.uk/
+ * Ben Dooks <ben@simtec.co.uk>
+ *
+ * ARM PrimeCell PL080 DMA controller
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+/* Note, there are some Samsung updates to this controller block which
+ * make it not entierly compatible with the PL080 specification from
+ * ARM. When in doubt, check the Samsung documentation first.
+ *
+ * The Samsung defines are PL080S, and add an extra controll register,
+ * the ability to move more than 2^11 counts of data and some extra
+ * OneNAND features.
+*/
+
+#define PL080_INT_STATUS (0x00)
+#define PL080_TC_STATUS (0x04)
+#define PL080_TC_CLEAR (0x08)
+#define PL080_ERR_STATUS (0x0C)
+#define PL080_ERR_CLEAR (0x10)
+#define PL080_RAW_TC_STATUS (0x14)
+#define PL080_RAW_ERR_STATUS (0x18)
+#define PL080_EN_CHAN (0x1c)
+#define PL080_SOFT_BREQ (0x20)
+#define PL080_SOFT_SREQ (0x24)
+#define PL080_SOFT_LBREQ (0x28)
+#define PL080_SOFT_LSREQ (0x2C)
+
+#define PL080_CONFIG (0x30)
+#define PL080_CONFIG_M2_BE (1 << 2)
+#define PL080_CONFIG_M1_BE (1 << 1)
+#define PL080_CONFIG_ENABLE (1 << 0)
+
+#define PL080_SYNC (0x34)
+
+/* Per channel configuration registers */
+
+#define PL008_Cx_STRIDE (0x20)
+#define PL080_Cx_BASE(x) ((0x100 + (x * 0x20)))
+#define PL080_Cx_SRC_ADDR(x) ((0x100 + (x * 0x20)))
+#define PL080_Cx_DST_ADDR(x) ((0x104 + (x * 0x20)))
+#define PL080_Cx_LLI(x) ((0x108 + (x * 0x20)))
+#define PL080_Cx_CONTROL(x) ((0x10C + (x * 0x20)))
+#define PL080_Cx_CONFIG(x) ((0x110 + (x * 0x20)))
+#define PL080S_Cx_CONTROL2(x) ((0x110 + (x * 0x20)))
+#define PL080S_Cx_CONFIG(x) ((0x114 + (x * 0x20)))
+
+#define PL080_CH_SRC_ADDR (0x00)
+#define PL080_CH_DST_ADDR (0x04)
+#define PL080_CH_LLI (0x08)
+#define PL080_CH_CONTROL (0x0C)
+#define PL080_CH_CONFIG (0x10)
+#define PL080S_CH_CONTROL2 (0x10)
+#define PL080S_CH_CONFIG (0x14)
+
+#define PL080_LLI_ADDR_MASK (0x3fffffff << 2)
+#define PL080_LLI_ADDR_SHIFT (2)
+#define PL080_LLI_LM_AHB2 (1 << 0)
+
+#define PL080_CONTROL_TC_IRQ_EN (1 << 31)
+#define PL080_CONTROL_PROT_MASK (0x7 << 28)
+#define PL080_CONTROL_PROT_SHIFT (28)
+#define PL080_CONTROL_PROT_SYS (1 << 28)
+#define PL080_CONTROL_DST_INCR (1 << 27)
+#define PL080_CONTROL_SRC_INCR (1 << 26)
+#define PL080_CONTROL_DST_AHB2 (1 << 25)
+#define PL080_CONTROL_SRC_AHB2 (1 << 24)
+#define PL080_CONTROL_DWIDTH_MASK (0x7 << 21)
+#define PL080_CONTROL_DWIDTH_SHIFT (21)
+#define PL080_CONTROL_SWIDTH_MASK (0x7 << 18)
+#define PL080_CONTROL_SWIDTH_SHIFT (18)
+#define PL080_CONTROL_DB_SIZE_MASK (0x7 << 15)
+#define PL080_CONTROL_DB_SIZE_SHIFT (15)
+#define PL080_CONTROL_SB_SIZE_MASK (0x7 << 12)
+#define PL080_CONTROL_SB_SIZE_SHIFT (12)
+#define PL080_CONTROL_TRANSFER_SIZE_MASK (0xfff << 0)
+#define PL080_CONTROL_TRANSFER_SIZE_SHIFT (0)
+
+#define PL080_BSIZE_1 (0x0)
+#define PL080_BSIZE_4 (0x1)
+#define PL080_BSIZE_8 (0x2)
+#define PL080_BSIZE_16 (0x3)
+#define PL080_BSIZE_32 (0x4)
+#define PL080_BSIZE_64 (0x5)
+#define PL080_BSIZE_128 (0x6)
+#define PL080_BSIZE_256 (0x7)
+
+#define PL080_WIDTH_8BIT (0x0)
+#define PL080_WIDTH_16BIT (0x1)
+#define PL080_WIDTH_32BIT (0x2)
+
+#define PL080_CONFIG_HALT (1 << 18)
+#define PL080_CONFIG_ACTIVE (1 << 17) /* RO */
+#define PL080_CONFIG_LOCK (1 << 16)
+#define PL080_CONFIG_TC_IRQ_MASK (1 << 15)
+#define PL080_CONFIG_ERR_IRQ_MASK (1 << 14)
+#define PL080_CONFIG_FLOW_CONTROL_MASK (0x7 << 11)
+#define PL080_CONFIG_FLOW_CONTROL_SHIFT (11)
+#define PL080_CONFIG_DST_SEL_MASK (0xf << 6)
+#define PL080_CONFIG_DST_SEL_SHIFT (6)
+#define PL080_CONFIG_SRC_SEL_MASK (0xf << 1)
+#define PL080_CONFIG_SRC_SEL_SHIFT (1)
+#define PL080_CONFIG_ENABLE (1 << 0)
+
+#define PL080_FLOW_MEM2MEM (0x0)
+#define PL080_FLOW_MEM2PER (0x1)
+#define PL080_FLOW_PER2MEM (0x2)
+#define PL080_FLOW_SRC2DST (0x3)
+#define PL080_FLOW_SRC2DST_DST (0x4)
+#define PL080_FLOW_MEM2PER_PER (0x5)
+#define PL080_FLOW_PER2MEM_PER (0x6)
+#define PL080_FLOW_SRC2DST_SRC (0x7)
+
+/* DMA linked list chain structure */
+
+struct pl080_lli {
+ u32 src_addr;
+ u32 dst_addr;
+ u32 next_lli;
+ u32 control0;
+};
+
+struct pl080s_lli {
+ u32 src_addr;
+ u32 dst_addr;
+ u32 next_lli;
+ u32 control0;
+ u32 control1;
+};
+
diff --git a/arch/arm/include/asm/hardware/vic.h b/arch/arm/include/asm/hardware/vic.h
index f87328d..5d72550 100644
--- a/arch/arm/include/asm/hardware/vic.h
+++ b/arch/arm/include/asm/hardware/vic.h
@@ -41,7 +41,7 @@
#define VIC_PL192_VECT_ADDR 0xF00
#ifndef __ASSEMBLY__
-void vic_init(void __iomem *base, unsigned int irq_start, u32 vic_sources);
+void vic_init(void __iomem *base, unsigned int irq_start, u32 vic_sources, u32 resume_sources);
#endif
#endif
diff --git a/arch/arm/mach-ep93xx/core.c b/arch/arm/mach-ep93xx/core.c
index f477df0..204dc5c 100644
--- a/arch/arm/mach-ep93xx/core.c
+++ b/arch/arm/mach-ep93xx/core.c
@@ -362,8 +362,8 @@
{
int gpio_irq;
- vic_init((void *)EP93XX_VIC1_BASE, 0, EP93XX_VIC1_VALID_IRQ_MASK);
- vic_init((void *)EP93XX_VIC2_BASE, 32, EP93XX_VIC2_VALID_IRQ_MASK);
+ vic_init((void *)EP93XX_VIC1_BASE, 0, EP93XX_VIC1_VALID_IRQ_MASK, 0);
+ vic_init((void *)EP93XX_VIC2_BASE, 32, EP93XX_VIC2_VALID_IRQ_MASK, 0);
for (gpio_irq = gpio_to_irq(0);
gpio_irq <= gpio_to_irq(EP93XX_GPIO_LINE_MAX_IRQ); ++gpio_irq) {
diff --git a/arch/arm/mach-netx/generic.c b/arch/arm/mach-netx/generic.c
index 79df60c..43da8bb 100644
--- a/arch/arm/mach-netx/generic.c
+++ b/arch/arm/mach-netx/generic.c
@@ -168,7 +168,7 @@
{
int irq;
- vic_init(__io(io_p2v(NETX_PA_VIC)), 0, ~0);
+ vic_init(__io(io_p2v(NETX_PA_VIC)), 0, ~0, 0);
for (irq = NETX_IRQ_HIF_CHAINED(0); irq <= NETX_IRQ_HIF_LAST; irq++) {
set_irq_chip(irq, &netx_hif_chip);
diff --git a/arch/arm/mach-s3c2400/gpio.c b/arch/arm/mach-s3c2400/gpio.c
index 7a7ed417..6c68e78 100644
--- a/arch/arm/mach-s3c2400/gpio.c
+++ b/arch/arm/mach-s3c2400/gpio.c
@@ -33,10 +33,10 @@
int s3c2400_gpio_getirq(unsigned int pin)
{
- if (pin < S3C2410_GPE0 || pin > S3C2400_GPE7_EINT7)
- return -1; /* not valid interrupts */
+ if (pin < S3C2410_GPE(0) || pin > S3C2400_GPE(7))
+ return -EINVAL; /* not valid interrupts */
- return (pin - S3C2410_GPE0) + IRQ_EINT0;
+ return (pin - S3C2410_GPE(0)) + IRQ_EINT0;
}
EXPORT_SYMBOL(s3c2400_gpio_getirq);
diff --git a/arch/arm/mach-s3c2410/Kconfig b/arch/arm/mach-s3c2410/Kconfig
index 63a30d1..41bb65d 100644
--- a/arch/arm/mach-s3c2410/Kconfig
+++ b/arch/arm/mach-s3c2410/Kconfig
@@ -59,6 +59,7 @@
bool "IPAQ H1940"
select CPU_S3C2410
select PM_H1940 if PM
+ select S3C_DEV_USB_HOST
help
Say Y here if you are using the HP IPAQ H1940
@@ -70,6 +71,7 @@
config MACH_N30
bool "Acer N30 family"
select CPU_S3C2410
+ select S3C_DEV_USB_HOST
help
Say Y here if you want suppt for the Acer N30, Acer N35,
Navman PiN570, Yakumo AlphaX or Airis NC05 PDAs.
@@ -82,6 +84,7 @@
select MACH_BAST_IDE
select S3C24XX_DCLK
select ISA
+ select S3C_DEV_USB_HOST
help
Say Y here if you are using the Simtec Electronics EB2410ITX
development board (also known as BAST)
@@ -89,6 +92,7 @@
config MACH_OTOM
bool "NexVision OTOM Board"
select CPU_S3C2410
+ select S3C_DEV_USB_HOST
help
Say Y here if you are using the Nex Vision OTOM board
@@ -96,6 +100,7 @@
bool "AML M5900 Series"
select CPU_S3C2410
select PM_SIMTEC if PM
+ select S3C_DEV_USB_HOST
help
Say Y here if you are using the American Microsystems M5900 Series
<http://www.amltd.com>
@@ -111,6 +116,7 @@
config MACH_TCT_HAMMER
bool "TCT Hammer Board"
select CPU_S3C2410
+ select S3C_DEV_USB_HOST
help
Say Y here if you are using the TinCanTools Hammer Board
<http://www.tincantools.com>
@@ -122,12 +128,14 @@
select SIMTEC_NOR
select MACH_BAST_IDE
select CPU_S3C2410
+ select S3C_DEV_USB_HOST
help
Say Y here if you are using the Thorcom VR1000 board.
config MACH_QT2410
bool "QT2410"
select CPU_S3C2410
+ select S3C_DEV_USB_HOST
help
Say Y here if you are using the Armzone QT2410
diff --git a/arch/arm/mach-s3c2410/dma.c b/arch/arm/mach-s3c2410/dma.c
index 440c014..dbf96e6 100644
--- a/arch/arm/mach-s3c2410/dma.c
+++ b/arch/arm/mach-s3c2410/dma.c
@@ -17,14 +17,16 @@
#include <linux/sysdev.h>
#include <linux/serial_core.h>
+#include <mach/map.h>
#include <mach/dma.h>
#include <plat/cpu.h>
-#include <plat/dma.h>
+#include <plat/dma-plat.h>
#include <plat/regs-serial.h>
#include <mach/regs-gpio.h>
#include <plat/regs-ac97.h>
+#include <plat/regs-dma.h>
#include <mach/regs-mem.h>
#include <mach/regs-lcd.h>
#include <mach/regs-sdi.h>
diff --git a/arch/arm/mach-s3c2410/gpio.c b/arch/arm/mach-s3c2410/gpio.c
index 36a3132..7974afc 100644
--- a/arch/arm/mach-s3c2410/gpio.c
+++ b/arch/arm/mach-s3c2410/gpio.c
@@ -39,12 +39,12 @@
unsigned long flags;
unsigned long val;
- if (pin < S3C2410_GPG8 || pin > S3C2410_GPG15)
- return -1;
+ if (pin < S3C2410_GPG(8) || pin > S3C2410_GPG(15))
+ return -EINVAL;
config &= 0xff;
- pin -= S3C2410_GPG8;
+ pin -= S3C2410_GPG(8);
reg += pin & ~3;
local_irq_save(flags);
diff --git a/arch/arm/mach-s3c2410/h1940-bluetooth.c b/arch/arm/mach-s3c2410/h1940-bluetooth.c
index 5a6bc56..5aabf11 100644
--- a/arch/arm/mach-s3c2410/h1940-bluetooth.c
+++ b/arch/arm/mach-s3c2410/h1940-bluetooth.c
@@ -16,6 +16,8 @@
#include <linux/string.h>
#include <linux/ctype.h>
#include <linux/leds.h>
+#include <linux/gpio.h>
+
#include <mach/regs-gpio.h>
#include <mach/hardware.h>
#include <mach/h1940-latch.h>
@@ -41,9 +43,9 @@
h1940_latch_control(0, H1940_LATCH_BLUETOOTH_POWER);
/* Reset the chip */
mdelay(10);
- s3c2410_gpio_setpin(S3C2410_GPH1, 1);
+ s3c2410_gpio_setpin(S3C2410_GPH(1), 1);
mdelay(10);
- s3c2410_gpio_setpin(S3C2410_GPH1, 0);
+ s3c2410_gpio_setpin(S3C2410_GPH(1), 0);
state = 1;
}
@@ -52,9 +54,9 @@
led_trigger_event(bt_led_trigger, 0);
#endif
- s3c2410_gpio_setpin(S3C2410_GPH1, 1);
+ s3c2410_gpio_setpin(S3C2410_GPH(1), 1);
mdelay(10);
- s3c2410_gpio_setpin(S3C2410_GPH1, 0);
+ s3c2410_gpio_setpin(S3C2410_GPH(1), 0);
mdelay(10);
h1940_latch_control(H1940_LATCH_BLUETOOTH_POWER, 0);
@@ -87,14 +89,14 @@
static int __init h1940bt_probe(struct platform_device *pdev)
{
/* Configures BT serial port GPIOs */
- s3c2410_gpio_cfgpin(S3C2410_GPH0, S3C2410_GPH0_nCTS0);
- s3c2410_gpio_pullup(S3C2410_GPH0, 1);
- s3c2410_gpio_cfgpin(S3C2410_GPH1, S3C2410_GPH1_OUTP);
- s3c2410_gpio_pullup(S3C2410_GPH1, 1);
- s3c2410_gpio_cfgpin(S3C2410_GPH2, S3C2410_GPH2_TXD0);
- s3c2410_gpio_pullup(S3C2410_GPH2, 1);
- s3c2410_gpio_cfgpin(S3C2410_GPH3, S3C2410_GPH3_RXD0);
- s3c2410_gpio_pullup(S3C2410_GPH3, 1);
+ s3c2410_gpio_cfgpin(S3C2410_GPH(0), S3C2410_GPH0_nCTS0);
+ s3c2410_gpio_pullup(S3C2410_GPH(0), 1);
+ s3c2410_gpio_cfgpin(S3C2410_GPH(1), S3C2410_GPIO_OUTPUT);
+ s3c2410_gpio_pullup(S3C2410_GPH(1), 1);
+ s3c2410_gpio_cfgpin(S3C2410_GPH(2), S3C2410_GPH2_TXD0);
+ s3c2410_gpio_pullup(S3C2410_GPH(2), 1);
+ s3c2410_gpio_cfgpin(S3C2410_GPH(3), S3C2410_GPH3_RXD0);
+ s3c2410_gpio_pullup(S3C2410_GPH(3), 1);
#ifdef CONFIG_LEDS_H1940
led_trigger_register_simple("h1940-bluetooth", &bt_led_trigger);
diff --git a/arch/arm/mach-s3c2410/include/mach/dma.h b/arch/arm/mach-s3c2410/include/mach/dma.h
index 13358ce..c3a2629 100644
--- a/arch/arm/mach-s3c2410/include/mach/dma.h
+++ b/arch/arm/mach-s3c2410/include/mach/dma.h
@@ -3,7 +3,7 @@
* Copyright (C) 2003,2004,2006 Simtec Electronics
* Ben Dooks <ben@simtec.co.uk>
*
- * Samsung S3C241XX DMA support
+ * Samsung S3C24XX DMA support
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
@@ -13,8 +13,8 @@
#ifndef __ASM_ARCH_DMA_H
#define __ASM_ARCH_DMA_H __FILE__
+#include <plat/dma.h>
#include <linux/sysdev.h>
-#include <mach/hardware.h>
#define MAX_DMA_TRANSFER_SIZE 0x100000 /* Data Unit is half word */
@@ -55,9 +55,9 @@
/* we have 4 dma channels */
#ifndef CONFIG_CPU_S3C2443
-#define S3C2410_DMA_CHANNELS (4)
+#define S3C_DMA_CHANNELS (4)
#else
-#define S3C2410_DMA_CHANNELS (6)
+#define S3C_DMA_CHANNELS (6)
#endif
/* types */
@@ -68,7 +68,6 @@
S3C2410_DMA_PAUSED
};
-
/* enum s3c2410_dma_loadst
*
* This represents the state of the DMA engine, wrt to the loaded / running
@@ -104,32 +103,6 @@
S3C2410_DMALOAD_1LOADED_1RUNNING,
};
-enum s3c2410_dma_buffresult {
- S3C2410_RES_OK,
- S3C2410_RES_ERR,
- S3C2410_RES_ABORT
-};
-
-enum s3c2410_dmasrc {
- S3C2410_DMASRC_HW, /* source is memory */
- S3C2410_DMASRC_MEM /* source is hardware */
-};
-
-/* enum s3c2410_chan_op
- *
- * operation codes passed to the DMA code by the user, and also used
- * to inform the current channel owner of any changes to the system state
-*/
-
-enum s3c2410_chan_op {
- S3C2410_DMAOP_START,
- S3C2410_DMAOP_STOP,
- S3C2410_DMAOP_PAUSE,
- S3C2410_DMAOP_RESUME,
- S3C2410_DMAOP_FLUSH,
- S3C2410_DMAOP_TIMEOUT, /* internal signal to handler */
- S3C2410_DMAOP_STARTED, /* indicate channel started */
-};
/* flags */
@@ -139,17 +112,14 @@
/* dma buffer */
-struct s3c2410_dma_client {
- char *name;
-};
+struct s3c2410_dma_buf;
-/* s3c2410_dma_buf_s
+/* s3c2410_dma_buf
*
* internally used buffer structure to describe a queued or running
* buffer.
*/
-struct s3c2410_dma_buf;
struct s3c2410_dma_buf {
struct s3c2410_dma_buf *next;
int magic; /* magic */
@@ -161,20 +131,6 @@
/* [1] is this updated for both recv/send modes? */
-struct s3c2410_dma_chan;
-
-/* s3c2410_dma_cbfn_t
- *
- * buffer callback routine type
-*/
-
-typedef void (*s3c2410_dma_cbfn_t)(struct s3c2410_dma_chan *,
- void *buf, int size,
- enum s3c2410_dma_buffresult result);
-
-typedef int (*s3c2410_dma_opfn_t)(struct s3c2410_dma_chan *,
- enum s3c2410_chan_op );
-
struct s3c2410_dma_stats {
unsigned long loads;
unsigned long timeout_longest;
@@ -206,10 +162,10 @@
/* channel configuration */
enum s3c2410_dmasrc source;
+ enum dma_ch req_ch;
unsigned long dev_addr;
unsigned long load_timeout;
unsigned int flags; /* channel flags */
- unsigned int hw_cfg; /* last hw config */
struct s3c24xx_dma_map *map; /* channel hw maps */
@@ -236,213 +192,6 @@
struct sys_device dev;
};
-/* the currently allocated channel information */
-extern struct s3c2410_dma_chan s3c2410_chans[];
-
-/* note, we don't really use dma_device_t at the moment */
typedef unsigned long dma_device_t;
-/* functions --------------------------------------------------------------- */
-
-/* s3c2410_dma_request
- *
- * request a dma channel exclusivley
-*/
-
-extern int s3c2410_dma_request(unsigned int channel,
- struct s3c2410_dma_client *, void *dev);
-
-
-/* s3c2410_dma_ctrl
- *
- * change the state of the dma channel
-*/
-
-extern int s3c2410_dma_ctrl(unsigned int channel, enum s3c2410_chan_op op);
-
-/* s3c2410_dma_setflags
- *
- * set the channel's flags to a given state
-*/
-
-extern int s3c2410_dma_setflags(unsigned int channel,
- unsigned int flags);
-
-/* s3c2410_dma_free
- *
- * free the dma channel (will also abort any outstanding operations)
-*/
-
-extern int s3c2410_dma_free(unsigned int channel, struct s3c2410_dma_client *);
-
-/* s3c2410_dma_enqueue
- *
- * place the given buffer onto the queue of operations for the channel.
- * The buffer must be allocated from dma coherent memory, or the Dcache/WB
- * drained before the buffer is given to the DMA system.
-*/
-
-extern int s3c2410_dma_enqueue(unsigned int channel, void *id,
- dma_addr_t data, int size);
-
-/* s3c2410_dma_config
- *
- * configure the dma channel
-*/
-
-extern int s3c2410_dma_config(unsigned int channel, int xferunit, int dcon);
-
-/* s3c2410_dma_devconfig
- *
- * configure the device we're talking to
-*/
-
-extern int s3c2410_dma_devconfig(int channel, enum s3c2410_dmasrc source,
- int hwcfg, unsigned long devaddr);
-
-/* s3c2410_dma_getposition
- *
- * get the position that the dma transfer is currently at
-*/
-
-extern int s3c2410_dma_getposition(unsigned int channel,
- dma_addr_t *src, dma_addr_t *dest);
-
-extern int s3c2410_dma_set_opfn(unsigned int, s3c2410_dma_opfn_t rtn);
-extern int s3c2410_dma_set_buffdone_fn(unsigned int, s3c2410_dma_cbfn_t rtn);
-
-/* DMA Register definitions */
-
-#define S3C2410_DMA_DISRC (0x00)
-#define S3C2410_DMA_DISRCC (0x04)
-#define S3C2410_DMA_DIDST (0x08)
-#define S3C2410_DMA_DIDSTC (0x0C)
-#define S3C2410_DMA_DCON (0x10)
-#define S3C2410_DMA_DSTAT (0x14)
-#define S3C2410_DMA_DCSRC (0x18)
-#define S3C2410_DMA_DCDST (0x1C)
-#define S3C2410_DMA_DMASKTRIG (0x20)
-#define S3C2412_DMA_DMAREQSEL (0x24)
-#define S3C2443_DMA_DMAREQSEL (0x24)
-
-#define S3C2410_DISRCC_INC (1<<0)
-#define S3C2410_DISRCC_APB (1<<1)
-
-#define S3C2410_DMASKTRIG_STOP (1<<2)
-#define S3C2410_DMASKTRIG_ON (1<<1)
-#define S3C2410_DMASKTRIG_SWTRIG (1<<0)
-
-#define S3C2410_DCON_DEMAND (0<<31)
-#define S3C2410_DCON_HANDSHAKE (1<<31)
-#define S3C2410_DCON_SYNC_PCLK (0<<30)
-#define S3C2410_DCON_SYNC_HCLK (1<<30)
-
-#define S3C2410_DCON_INTREQ (1<<29)
-
-#define S3C2410_DCON_CH0_XDREQ0 (0<<24)
-#define S3C2410_DCON_CH0_UART0 (1<<24)
-#define S3C2410_DCON_CH0_SDI (2<<24)
-#define S3C2410_DCON_CH0_TIMER (3<<24)
-#define S3C2410_DCON_CH0_USBEP1 (4<<24)
-
-#define S3C2410_DCON_CH1_XDREQ1 (0<<24)
-#define S3C2410_DCON_CH1_UART1 (1<<24)
-#define S3C2410_DCON_CH1_I2SSDI (2<<24)
-#define S3C2410_DCON_CH1_SPI (3<<24)
-#define S3C2410_DCON_CH1_USBEP2 (4<<24)
-
-#define S3C2410_DCON_CH2_I2SSDO (0<<24)
-#define S3C2410_DCON_CH2_I2SSDI (1<<24)
-#define S3C2410_DCON_CH2_SDI (2<<24)
-#define S3C2410_DCON_CH2_TIMER (3<<24)
-#define S3C2410_DCON_CH2_USBEP3 (4<<24)
-
-#define S3C2410_DCON_CH3_UART2 (0<<24)
-#define S3C2410_DCON_CH3_SDI (1<<24)
-#define S3C2410_DCON_CH3_SPI (2<<24)
-#define S3C2410_DCON_CH3_TIMER (3<<24)
-#define S3C2410_DCON_CH3_USBEP4 (4<<24)
-
-#define S3C2410_DCON_SRCSHIFT (24)
-#define S3C2410_DCON_SRCMASK (7<<24)
-
-#define S3C2410_DCON_BYTE (0<<20)
-#define S3C2410_DCON_HALFWORD (1<<20)
-#define S3C2410_DCON_WORD (2<<20)
-
-#define S3C2410_DCON_AUTORELOAD (0<<22)
-#define S3C2410_DCON_NORELOAD (1<<22)
-#define S3C2410_DCON_HWTRIG (1<<23)
-
-#ifdef CONFIG_CPU_S3C2440
-#define S3C2440_DIDSTC_CHKINT (1<<2)
-
-#define S3C2440_DCON_CH0_I2SSDO (5<<24)
-#define S3C2440_DCON_CH0_PCMIN (6<<24)
-
-#define S3C2440_DCON_CH1_PCMOUT (5<<24)
-#define S3C2440_DCON_CH1_SDI (6<<24)
-
-#define S3C2440_DCON_CH2_PCMIN (5<<24)
-#define S3C2440_DCON_CH2_MICIN (6<<24)
-
-#define S3C2440_DCON_CH3_MICIN (5<<24)
-#define S3C2440_DCON_CH3_PCMOUT (6<<24)
-#endif
-
-#ifdef CONFIG_CPU_S3C2412
-
-#define S3C2412_DMAREQSEL_SRC(x) ((x)<<1)
-
-#define S3C2412_DMAREQSEL_HW (1)
-
-#define S3C2412_DMAREQSEL_SPI0TX S3C2412_DMAREQSEL_SRC(0)
-#define S3C2412_DMAREQSEL_SPI0RX S3C2412_DMAREQSEL_SRC(1)
-#define S3C2412_DMAREQSEL_SPI1TX S3C2412_DMAREQSEL_SRC(2)
-#define S3C2412_DMAREQSEL_SPI1RX S3C2412_DMAREQSEL_SRC(3)
-#define S3C2412_DMAREQSEL_I2STX S3C2412_DMAREQSEL_SRC(4)
-#define S3C2412_DMAREQSEL_I2SRX S3C2412_DMAREQSEL_SRC(5)
-#define S3C2412_DMAREQSEL_TIMER S3C2412_DMAREQSEL_SRC(9)
-#define S3C2412_DMAREQSEL_SDI S3C2412_DMAREQSEL_SRC(10)
-#define S3C2412_DMAREQSEL_USBEP1 S3C2412_DMAREQSEL_SRC(13)
-#define S3C2412_DMAREQSEL_USBEP2 S3C2412_DMAREQSEL_SRC(14)
-#define S3C2412_DMAREQSEL_USBEP3 S3C2412_DMAREQSEL_SRC(15)
-#define S3C2412_DMAREQSEL_USBEP4 S3C2412_DMAREQSEL_SRC(16)
-#define S3C2412_DMAREQSEL_XDREQ0 S3C2412_DMAREQSEL_SRC(17)
-#define S3C2412_DMAREQSEL_XDREQ1 S3C2412_DMAREQSEL_SRC(18)
-#define S3C2412_DMAREQSEL_UART0_0 S3C2412_DMAREQSEL_SRC(19)
-#define S3C2412_DMAREQSEL_UART0_1 S3C2412_DMAREQSEL_SRC(20)
-#define S3C2412_DMAREQSEL_UART1_0 S3C2412_DMAREQSEL_SRC(21)
-#define S3C2412_DMAREQSEL_UART1_1 S3C2412_DMAREQSEL_SRC(22)
-#define S3C2412_DMAREQSEL_UART2_0 S3C2412_DMAREQSEL_SRC(23)
-#define S3C2412_DMAREQSEL_UART2_1 S3C2412_DMAREQSEL_SRC(24)
-
-#endif
-
-#define S3C2443_DMAREQSEL_SRC(x) ((x)<<1)
-
-#define S3C2443_DMAREQSEL_HW (1)
-
-#define S3C2443_DMAREQSEL_SPI0TX S3C2443_DMAREQSEL_SRC(0)
-#define S3C2443_DMAREQSEL_SPI0RX S3C2443_DMAREQSEL_SRC(1)
-#define S3C2443_DMAREQSEL_SPI1TX S3C2443_DMAREQSEL_SRC(2)
-#define S3C2443_DMAREQSEL_SPI1RX S3C2443_DMAREQSEL_SRC(3)
-#define S3C2443_DMAREQSEL_I2STX S3C2443_DMAREQSEL_SRC(4)
-#define S3C2443_DMAREQSEL_I2SRX S3C2443_DMAREQSEL_SRC(5)
-#define S3C2443_DMAREQSEL_TIMER S3C2443_DMAREQSEL_SRC(9)
-#define S3C2443_DMAREQSEL_SDI S3C2443_DMAREQSEL_SRC(10)
-#define S3C2443_DMAREQSEL_XDREQ0 S3C2443_DMAREQSEL_SRC(17)
-#define S3C2443_DMAREQSEL_XDREQ1 S3C2443_DMAREQSEL_SRC(18)
-#define S3C2443_DMAREQSEL_UART0_0 S3C2443_DMAREQSEL_SRC(19)
-#define S3C2443_DMAREQSEL_UART0_1 S3C2443_DMAREQSEL_SRC(20)
-#define S3C2443_DMAREQSEL_UART1_0 S3C2443_DMAREQSEL_SRC(21)
-#define S3C2443_DMAREQSEL_UART1_1 S3C2443_DMAREQSEL_SRC(22)
-#define S3C2443_DMAREQSEL_UART2_0 S3C2443_DMAREQSEL_SRC(23)
-#define S3C2443_DMAREQSEL_UART2_1 S3C2443_DMAREQSEL_SRC(24)
-#define S3C2443_DMAREQSEL_UART3_0 S3C2443_DMAREQSEL_SRC(25)
-#define S3C2443_DMAREQSEL_UART3_1 S3C2443_DMAREQSEL_SRC(26)
-#define S3C2443_DMAREQSEL_PCMOUT S3C2443_DMAREQSEL_SRC(27)
-#define S3C2443_DMAREQSEL_PCMIN S3C2443_DMAREQSEL_SRC(28)
-#define S3C2443_DMAREQSEL_MICIN S3C2443_DMAREQSEL_SRC(29)
-
#endif /* __ASM_ARCH_DMA_H */
diff --git a/arch/arm/mach-s3c2410/include/mach/gpio-core.h b/arch/arm/mach-s3c2410/include/mach/gpio-core.h
index 6c9fbb9..8fe1920 100644
--- a/arch/arm/mach-s3c2410/include/mach/gpio-core.h
+++ b/arch/arm/mach-s3c2410/include/mach/gpio-core.h
@@ -24,7 +24,7 @@
{
struct s3c_gpio_chip *chip;
- if (pin > S3C2410_GPG10)
+ if (pin > S3C2410_GPG(10))
return NULL;
chip = &s3c24xx_gpios[pin/32];
diff --git a/arch/arm/mach-s3c2410/include/mach/gpio-fns.h b/arch/arm/mach-s3c2410/include/mach/gpio-fns.h
new file mode 100644
index 0000000..801dff1
--- /dev/null
+++ b/arch/arm/mach-s3c2410/include/mach/gpio-fns.h
@@ -0,0 +1,103 @@
+/* arch/arm/mach-s3c2410/include/mach/gpio-fns.h
+ *
+ * Copyright (c) 2003,2009 Simtec Electronics
+ * Ben Dooks <ben@simtec.co.uk>
+ *
+ * S3C2410 - hardware
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+/* These functions are in the to-be-removed category and it is strongly
+ * encouraged not to use these in new code. They will be marked deprecated
+ * very soon.
+ *
+ * Most of the functionality can be either replaced by the gpiocfg calls
+ * for the s3c platform or by the generic GPIOlib API.
+*/
+
+/* external functions for GPIO support
+ *
+ * These allow various different clients to access the same GPIO
+ * registers without conflicting. If your driver only owns the entire
+ * GPIO register, then it is safe to ioremap/__raw_{read|write} to it.
+*/
+
+/* s3c2410_gpio_cfgpin
+ *
+ * set the configuration of the given pin to the value passed.
+ *
+ * eg:
+ * s3c2410_gpio_cfgpin(S3C2410_GPA(0), S3C2410_GPA0_ADDR0);
+ * s3c2410_gpio_cfgpin(S3C2410_GPE(8), S3C2410_GPE8_SDDAT1);
+*/
+
+extern void s3c2410_gpio_cfgpin(unsigned int pin, unsigned int function);
+
+extern unsigned int s3c2410_gpio_getcfg(unsigned int pin);
+
+/* s3c2410_gpio_getirq
+ *
+ * turn the given pin number into the corresponding IRQ number
+ *
+ * returns:
+ * < 0 = no interrupt for this pin
+ * >=0 = interrupt number for the pin
+*/
+
+extern int s3c2410_gpio_getirq(unsigned int pin);
+
+#ifdef CONFIG_CPU_S3C2400
+
+extern int s3c2400_gpio_getirq(unsigned int pin);
+
+#endif /* CONFIG_CPU_S3C2400 */
+
+/* s3c2410_gpio_irqfilter
+ *
+ * set the irq filtering on the given pin
+ *
+ * on = 0 => disable filtering
+ * 1 => enable filtering
+ *
+ * config = S3C2410_EINTFLT_PCLK or S3C2410_EINTFLT_EXTCLK orred with
+ * width of filter (0 through 63)
+ *
+ *
+*/
+
+extern int s3c2410_gpio_irqfilter(unsigned int pin, unsigned int on,
+ unsigned int config);
+
+/* s3c2410_gpio_pullup
+ *
+ * configure the pull-up control on the given pin
+ *
+ * to = 1 => disable the pull-up
+ * 0 => enable the pull-up
+ *
+ * eg;
+ *
+ * s3c2410_gpio_pullup(S3C2410_GPB(0), 0);
+ * s3c2410_gpio_pullup(S3C2410_GPE(8), 0);
+*/
+
+extern void s3c2410_gpio_pullup(unsigned int pin, unsigned int to);
+
+/* s3c2410_gpio_getpull
+ *
+ * Read the state of the pull-up on a given pin
+ *
+ * return:
+ * < 0 => error code
+ * 0 => enabled
+ * 1 => disabled
+*/
+
+extern int s3c2410_gpio_getpull(unsigned int pin);
+
+extern void s3c2410_gpio_setpin(unsigned int pin, unsigned int to);
+
+extern unsigned int s3c2410_gpio_getpin(unsigned int pin);
diff --git a/arch/arm/mach-s3c2410/include/mach/gpio-nrs.h b/arch/arm/mach-s3c2410/include/mach/gpio-nrs.h
index ce1ec69..2edbb9c 100644
--- a/arch/arm/mach-s3c2410/include/mach/gpio-nrs.h
+++ b/arch/arm/mach-s3c2410/include/mach/gpio-nrs.h
@@ -11,6 +11,9 @@
* published by the Free Software Foundation.
*/
+#ifndef __MACH_GPIONRS_H
+#define __MACH_GPIONRS_H
+
#define S3C2410_GPIONO(bank,offset) ((bank) + (offset))
#define S3C2410_GPIO_BANKA (32*0)
@@ -21,3 +24,70 @@
#define S3C2410_GPIO_BANKF (32*5)
#define S3C2410_GPIO_BANKG (32*6)
#define S3C2410_GPIO_BANKH (32*7)
+
+/* GPIO bank sizes */
+#define S3C2410_GPIO_A_NR (32)
+#define S3C2410_GPIO_B_NR (32)
+#define S3C2410_GPIO_C_NR (32)
+#define S3C2410_GPIO_D_NR (32)
+#define S3C2410_GPIO_E_NR (32)
+#define S3C2410_GPIO_F_NR (32)
+#define S3C2410_GPIO_G_NR (32)
+#define S3C2410_GPIO_H_NR (32)
+
+#if CONFIG_S3C_GPIO_SPACE != 0
+#error CONFIG_S3C_GPIO_SPACE cannot be zero at the moment
+#endif
+
+#define S3C2410_GPIO_NEXT(__gpio) \
+ ((__gpio##_START) + (__gpio##_NR) + CONFIG_S3C_GPIO_SPACE + 0)
+
+#ifndef __ASSEMBLY__
+
+enum s3c_gpio_number {
+ S3C2410_GPIO_A_START = 0,
+ S3C2410_GPIO_B_START = S3C2410_GPIO_NEXT(S3C2410_GPIO_A),
+ S3C2410_GPIO_C_START = S3C2410_GPIO_NEXT(S3C2410_GPIO_B),
+ S3C2410_GPIO_D_START = S3C2410_GPIO_NEXT(S3C2410_GPIO_C),
+ S3C2410_GPIO_E_START = S3C2410_GPIO_NEXT(S3C2410_GPIO_D),
+ S3C2410_GPIO_F_START = S3C2410_GPIO_NEXT(S3C2410_GPIO_E),
+ S3C2410_GPIO_G_START = S3C2410_GPIO_NEXT(S3C2410_GPIO_F),
+ S3C2410_GPIO_H_START = S3C2410_GPIO_NEXT(S3C2410_GPIO_G),
+};
+
+#endif /* __ASSEMBLY__ */
+
+/* S3C2410 GPIO number definitions. */
+
+#define S3C2410_GPA(_nr) (S3C2410_GPIO_A_START + (_nr))
+#define S3C2410_GPB(_nr) (S3C2410_GPIO_B_START + (_nr))
+#define S3C2410_GPC(_nr) (S3C2410_GPIO_C_START + (_nr))
+#define S3C2410_GPD(_nr) (S3C2410_GPIO_D_START + (_nr))
+#define S3C2410_GPE(_nr) (S3C2410_GPIO_E_START + (_nr))
+#define S3C2410_GPF(_nr) (S3C2410_GPIO_F_START + (_nr))
+#define S3C2410_GPG(_nr) (S3C2410_GPIO_G_START + (_nr))
+#define S3C2410_GPH(_nr) (S3C2410_GPIO_H_START + (_nr))
+
+/* compatibility until drivers can be modified */
+
+#define S3C2410_GPA0 S3C2410_GPA(0)
+#define S3C2410_GPA1 S3C2410_GPA(1)
+#define S3C2410_GPA3 S3C2410_GPA(3)
+#define S3C2410_GPA7 S3C2410_GPA(7)
+
+#define S3C2410_GPE0 S3C2410_GPE(0)
+#define S3C2410_GPE1 S3C2410_GPE(1)
+#define S3C2410_GPE2 S3C2410_GPE(2)
+#define S3C2410_GPE3 S3C2410_GPE(3)
+#define S3C2410_GPE4 S3C2410_GPE(4)
+#define S3C2410_GPE5 S3C2410_GPE(5)
+#define S3C2410_GPE6 S3C2410_GPE(6)
+#define S3C2410_GPE7 S3C2410_GPE(7)
+#define S3C2410_GPE8 S3C2410_GPE(8)
+#define S3C2410_GPE9 S3C2410_GPE(9)
+#define S3C2410_GPE10 S3C2410_GPE(10)
+
+#define S3C2410_GPH10 S3C2410_GPH(10)
+
+#endif /* __MACH_GPIONRS_H */
+
diff --git a/arch/arm/mach-s3c2410/include/mach/gpio.h b/arch/arm/mach-s3c2410/include/mach/gpio.h
index 51a88cf..15f0b3e 100644
--- a/arch/arm/mach-s3c2410/include/mach/gpio.h
+++ b/arch/arm/mach-s3c2410/include/mach/gpio.h
@@ -24,5 +24,6 @@
#include <asm-generic/gpio.h>
#include <mach/gpio-nrs.h>
+#include <mach/gpio-fns.h>
#define S3C_GPIO_END (S3C2410_GPIO_BANKH + 32)
diff --git a/arch/arm/mach-s3c2410/include/mach/hardware.h b/arch/arm/mach-s3c2410/include/mach/hardware.h
index 74d5a1a..aef5631 100644
--- a/arch/arm/mach-s3c2410/include/mach/hardware.h
+++ b/arch/arm/mach-s3c2410/include/mach/hardware.h
@@ -15,101 +15,6 @@
#ifndef __ASSEMBLY__
-/* external functions for GPIO support
- *
- * These allow various different clients to access the same GPIO
- * registers without conflicting. If your driver only owns the entire
- * GPIO register, then it is safe to ioremap/__raw_{read|write} to it.
-*/
-
-/* s3c2410_gpio_cfgpin
- *
- * set the configuration of the given pin to the value passed.
- *
- * eg:
- * s3c2410_gpio_cfgpin(S3C2410_GPA0, S3C2410_GPA0_ADDR0);
- * s3c2410_gpio_cfgpin(S3C2410_GPE8, S3C2410_GPE8_SDDAT1);
-*/
-
-extern void s3c2410_gpio_cfgpin(unsigned int pin, unsigned int function);
-
-extern unsigned int s3c2410_gpio_getcfg(unsigned int pin);
-
-/* s3c2410_gpio_getirq
- *
- * turn the given pin number into the corresponding IRQ number
- *
- * returns:
- * < 0 = no interrupt for this pin
- * >=0 = interrupt number for the pin
-*/
-
-extern int s3c2410_gpio_getirq(unsigned int pin);
-
-/* s3c2410_gpio_irq2pin
- *
- * turn the given irq number into the corresponding GPIO number
- *
- * returns:
- * < 0 = no pin
- * >=0 = gpio pin number
-*/
-
-extern int s3c2410_gpio_irq2pin(unsigned int irq);
-
-#ifdef CONFIG_CPU_S3C2400
-
-extern int s3c2400_gpio_getirq(unsigned int pin);
-
-#endif /* CONFIG_CPU_S3C2400 */
-
-/* s3c2410_gpio_irqfilter
- *
- * set the irq filtering on the given pin
- *
- * on = 0 => disable filtering
- * 1 => enable filtering
- *
- * config = S3C2410_EINTFLT_PCLK or S3C2410_EINTFLT_EXTCLK orred with
- * width of filter (0 through 63)
- *
- *
-*/
-
-extern int s3c2410_gpio_irqfilter(unsigned int pin, unsigned int on,
- unsigned int config);
-
-/* s3c2410_gpio_pullup
- *
- * configure the pull-up control on the given pin
- *
- * to = 1 => disable the pull-up
- * 0 => enable the pull-up
- *
- * eg;
- *
- * s3c2410_gpio_pullup(S3C2410_GPB0, 0);
- * s3c2410_gpio_pullup(S3C2410_GPE8, 0);
-*/
-
-extern void s3c2410_gpio_pullup(unsigned int pin, unsigned int to);
-
-/* s3c2410_gpio_getpull
- *
- * Read the state of the pull-up on a given pin
- *
- * return:
- * < 0 => error code
- * 0 => enabled
- * 1 => disabled
-*/
-
-extern int s3c2410_gpio_getpull(unsigned int pin);
-
-extern void s3c2410_gpio_setpin(unsigned int pin, unsigned int to);
-
-extern unsigned int s3c2410_gpio_getpin(unsigned int pin);
-
extern unsigned int s3c2410_modify_misccr(unsigned int clr, unsigned int chg);
#ifdef CONFIG_CPU_S3C2440
diff --git a/arch/arm/mach-s3c2410/include/mach/map.h b/arch/arm/mach-s3c2410/include/mach/map.h
index 255fdfe..e99b212 100644
--- a/arch/arm/mach-s3c2410/include/mach/map.h
+++ b/arch/arm/mach-s3c2410/include/mach/map.h
@@ -84,7 +84,6 @@
#define S3C24XX_PA_IRQ S3C2410_PA_IRQ
#define S3C24XX_PA_MEMCTRL S3C2410_PA_MEMCTRL
-#define S3C24XX_PA_USBHOST S3C2410_PA_USBHOST
#define S3C24XX_PA_DMA S3C2410_PA_DMA
#define S3C24XX_PA_CLKPWR S3C2410_PA_CLKPWR
#define S3C24XX_PA_LCD S3C2410_PA_LCD
@@ -102,6 +101,7 @@
#define S3C_PA_IIC S3C2410_PA_IIC
#define S3C_PA_UART S3C24XX_PA_UART
+#define S3C_PA_USBHOST S3C2410_PA_USBHOST
#define S3C_PA_HSMMC0 S3C2443_PA_HSMMC
#endif /* __ASM_ARCH_MAP_H */
diff --git a/arch/arm/mach-s3c2410/include/mach/regs-gpio.h b/arch/arm/mach-s3c2410/include/mach/regs-gpio.h
index 35a03df..b278d0c 100644
--- a/arch/arm/mach-s3c2410/include/mach/regs-gpio.h
+++ b/arch/arm/mach-s3c2410/include/mach/regs-gpio.h
@@ -69,104 +69,58 @@
#define S3C2400_GPACON S3C2410_GPIOREG(0x00)
#define S3C2400_GPADAT S3C2410_GPIOREG(0x04)
-#define S3C2410_GPA0 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 0)
-#define S3C2410_GPA0_OUT (0<<0)
#define S3C2410_GPA0_ADDR0 (1<<0)
-#define S3C2410_GPA1 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 1)
-#define S3C2410_GPA1_OUT (0<<1)
#define S3C2410_GPA1_ADDR16 (1<<1)
-#define S3C2410_GPA2 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 2)
-#define S3C2410_GPA2_OUT (0<<2)
#define S3C2410_GPA2_ADDR17 (1<<2)
-#define S3C2410_GPA3 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 3)
-#define S3C2410_GPA3_OUT (0<<3)
#define S3C2410_GPA3_ADDR18 (1<<3)
-#define S3C2410_GPA4 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 4)
-#define S3C2410_GPA4_OUT (0<<4)
#define S3C2410_GPA4_ADDR19 (1<<4)
-#define S3C2410_GPA5 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 5)
-#define S3C2410_GPA5_OUT (0<<5)
#define S3C2410_GPA5_ADDR20 (1<<5)
-#define S3C2410_GPA6 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 6)
-#define S3C2410_GPA6_OUT (0<<6)
#define S3C2410_GPA6_ADDR21 (1<<6)
-#define S3C2410_GPA7 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 7)
-#define S3C2410_GPA7_OUT (0<<7)
#define S3C2410_GPA7_ADDR22 (1<<7)
-#define S3C2410_GPA8 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 8)
-#define S3C2410_GPA8_OUT (0<<8)
#define S3C2410_GPA8_ADDR23 (1<<8)
-#define S3C2410_GPA9 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 9)
-#define S3C2410_GPA9_OUT (0<<9)
#define S3C2410_GPA9_ADDR24 (1<<9)
-#define S3C2410_GPA10 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 10)
-#define S3C2410_GPA10_OUT (0<<10)
#define S3C2410_GPA10_ADDR25 (1<<10)
#define S3C2400_GPA10_SCKE (1<<10)
-#define S3C2410_GPA11 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 11)
-#define S3C2410_GPA11_OUT (0<<11)
#define S3C2410_GPA11_ADDR26 (1<<11)
#define S3C2400_GPA11_nCAS0 (1<<11)
-#define S3C2410_GPA12 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 12)
-#define S3C2410_GPA12_OUT (0<<12)
#define S3C2410_GPA12_nGCS1 (1<<12)
#define S3C2400_GPA12_nCAS1 (1<<12)
-#define S3C2410_GPA13 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 13)
-#define S3C2410_GPA13_OUT (0<<13)
#define S3C2410_GPA13_nGCS2 (1<<13)
#define S3C2400_GPA13_nGCS1 (1<<13)
-#define S3C2410_GPA14 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 14)
-#define S3C2410_GPA14_OUT (0<<14)
#define S3C2410_GPA14_nGCS3 (1<<14)
#define S3C2400_GPA14_nGCS2 (1<<14)
-#define S3C2410_GPA15 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 15)
-#define S3C2410_GPA15_OUT (0<<15)
#define S3C2410_GPA15_nGCS4 (1<<15)
#define S3C2400_GPA15_nGCS3 (1<<15)
-#define S3C2410_GPA16 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 16)
-#define S3C2410_GPA16_OUT (0<<16)
#define S3C2410_GPA16_nGCS5 (1<<16)
#define S3C2400_GPA16_nGCS4 (1<<16)
-#define S3C2410_GPA17 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 17)
-#define S3C2410_GPA17_OUT (0<<17)
#define S3C2410_GPA17_CLE (1<<17)
#define S3C2400_GPA17_nGCS5 (1<<17)
-#define S3C2410_GPA18 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 18)
-#define S3C2410_GPA18_OUT (0<<18)
#define S3C2410_GPA18_ALE (1<<18)
-#define S3C2410_GPA19 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 19)
-#define S3C2410_GPA19_OUT (0<<19)
#define S3C2410_GPA19_nFWE (1<<19)
-#define S3C2410_GPA20 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 20)
-#define S3C2410_GPA20_OUT (0<<20)
#define S3C2410_GPA20_nFRE (1<<20)
-#define S3C2410_GPA21 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 21)
-#define S3C2410_GPA21_OUT (0<<21)
#define S3C2410_GPA21_nRSTOUT (1<<21)
-#define S3C2410_GPA22 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 22)
-#define S3C2410_GPA22_OUT (0<<22)
#define S3C2410_GPA22_nFCE (1<<22)
/* 0x08 and 0x0c are reserved on S3C2410 */
@@ -194,107 +148,69 @@
/* no i/o pin in port b can have value 3 (unless it is a s3c2443) ! */
-#define S3C2410_GPB0 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 0)
-#define S3C2410_GPB0_INP (0x00 << 0)
-#define S3C2410_GPB0_OUTP (0x01 << 0)
#define S3C2410_GPB0_TOUT0 (0x02 << 0)
#define S3C2400_GPB0_DATA16 (0x02 << 0)
-#define S3C2410_GPB1 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 1)
-#define S3C2410_GPB1_INP (0x00 << 2)
-#define S3C2410_GPB1_OUTP (0x01 << 2)
#define S3C2410_GPB1_TOUT1 (0x02 << 2)
#define S3C2400_GPB1_DATA17 (0x02 << 2)
-#define S3C2410_GPB2 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 2)
-#define S3C2410_GPB2_INP (0x00 << 4)
-#define S3C2410_GPB2_OUTP (0x01 << 4)
#define S3C2410_GPB2_TOUT2 (0x02 << 4)
#define S3C2400_GPB2_DATA18 (0x02 << 4)
#define S3C2400_GPB2_TCLK1 (0x03 << 4)
-#define S3C2410_GPB3 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 3)
-#define S3C2410_GPB3_INP (0x00 << 6)
-#define S3C2410_GPB3_OUTP (0x01 << 6)
#define S3C2410_GPB3_TOUT3 (0x02 << 6)
#define S3C2400_GPB3_DATA19 (0x02 << 6)
#define S3C2400_GPB3_TXD1 (0x03 << 6)
-#define S3C2410_GPB4 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 4)
-#define S3C2410_GPB4_INP (0x00 << 8)
-#define S3C2410_GPB4_OUTP (0x01 << 8)
#define S3C2410_GPB4_TCLK0 (0x02 << 8)
#define S3C2400_GPB4_DATA20 (0x02 << 8)
#define S3C2410_GPB4_MASK (0x03 << 8)
#define S3C2400_GPB4_RXD1 (0x03 << 8)
#define S3C2400_GPB4_MASK (0x03 << 8)
-#define S3C2410_GPB5 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 5)
-#define S3C2410_GPB5_INP (0x00 << 10)
-#define S3C2410_GPB5_OUTP (0x01 << 10)
#define S3C2410_GPB5_nXBACK (0x02 << 10)
#define S3C2443_GPB5_XBACK (0x03 << 10)
#define S3C2400_GPB5_DATA21 (0x02 << 10)
#define S3C2400_GPB5_nCTS1 (0x03 << 10)
-#define S3C2410_GPB6 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 6)
-#define S3C2410_GPB6_INP (0x00 << 12)
-#define S3C2410_GPB6_OUTP (0x01 << 12)
#define S3C2410_GPB6_nXBREQ (0x02 << 12)
#define S3C2443_GPB6_XBREQ (0x03 << 12)
#define S3C2400_GPB6_DATA22 (0x02 << 12)
#define S3C2400_GPB6_nRTS1 (0x03 << 12)
-#define S3C2410_GPB7 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 7)
-#define S3C2410_GPB7_INP (0x00 << 14)
-#define S3C2410_GPB7_OUTP (0x01 << 14)
#define S3C2410_GPB7_nXDACK1 (0x02 << 14)
#define S3C2443_GPB7_XDACK1 (0x03 << 14)
#define S3C2400_GPB7_DATA23 (0x02 << 14)
-#define S3C2410_GPB8 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 8)
-#define S3C2410_GPB8_INP (0x00 << 16)
-#define S3C2410_GPB8_OUTP (0x01 << 16)
#define S3C2410_GPB8_nXDREQ1 (0x02 << 16)
#define S3C2400_GPB8_DATA24 (0x02 << 16)
-#define S3C2410_GPB9 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 9)
-#define S3C2410_GPB9_INP (0x00 << 18)
-#define S3C2410_GPB9_OUTP (0x01 << 18)
#define S3C2410_GPB9_nXDACK0 (0x02 << 18)
#define S3C2443_GPB9_XDACK0 (0x03 << 18)
#define S3C2400_GPB9_DATA25 (0x02 << 18)
#define S3C2400_GPB9_I2SSDI (0x03 << 18)
-#define S3C2410_GPB10 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 10)
-#define S3C2410_GPB10_INP (0x00 << 20)
-#define S3C2410_GPB10_OUTP (0x01 << 20)
#define S3C2410_GPB10_nXDRE0 (0x02 << 20)
#define S3C2443_GPB10_XDREQ0 (0x03 << 20)
#define S3C2400_GPB10_DATA26 (0x02 << 20)
#define S3C2400_GPB10_nSS (0x03 << 20)
-#define S3C2400_GPB11 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 11)
#define S3C2400_GPB11_INP (0x00 << 22)
#define S3C2400_GPB11_OUTP (0x01 << 22)
#define S3C2400_GPB11_DATA27 (0x02 << 22)
-#define S3C2400_GPB12 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 12)
#define S3C2400_GPB12_INP (0x00 << 24)
#define S3C2400_GPB12_OUTP (0x01 << 24)
#define S3C2400_GPB12_DATA28 (0x02 << 24)
-#define S3C2400_GPB13 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 13)
#define S3C2400_GPB13_INP (0x00 << 26)
#define S3C2400_GPB13_OUTP (0x01 << 26)
#define S3C2400_GPB13_DATA29 (0x02 << 26)
-#define S3C2400_GPB14 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 14)
#define S3C2400_GPB14_INP (0x00 << 28)
#define S3C2400_GPB14_OUTP (0x01 << 28)
#define S3C2400_GPB14_DATA30 (0x02 << 28)
-#define S3C2400_GPB15 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 15)
#define S3C2400_GPB15_INP (0x00 << 30)
#define S3C2400_GPB15_OUTP (0x01 << 30)
#define S3C2400_GPB15_DATA31 (0x02 << 30)
@@ -315,99 +231,51 @@
#define S3C2400_GPCDAT S3C2410_GPIOREG(0x18)
#define S3C2400_GPCUP S3C2410_GPIOREG(0x1C)
-#define S3C2410_GPC0 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 0)
-#define S3C2410_GPC0_INP (0x00 << 0)
-#define S3C2410_GPC0_OUTP (0x01 << 0)
#define S3C2410_GPC0_LEND (0x02 << 0)
#define S3C2400_GPC0_VD0 (0x02 << 0)
-#define S3C2410_GPC1 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 1)
-#define S3C2410_GPC1_INP (0x00 << 2)
-#define S3C2410_GPC1_OUTP (0x01 << 2)
#define S3C2410_GPC1_VCLK (0x02 << 2)
#define S3C2400_GPC1_VD1 (0x02 << 2)
-#define S3C2410_GPC2 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 2)
-#define S3C2410_GPC2_INP (0x00 << 4)
-#define S3C2410_GPC2_OUTP (0x01 << 4)
#define S3C2410_GPC2_VLINE (0x02 << 4)
#define S3C2400_GPC2_VD2 (0x02 << 4)
-#define S3C2410_GPC3 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 3)
-#define S3C2410_GPC3_INP (0x00 << 6)
-#define S3C2410_GPC3_OUTP (0x01 << 6)
#define S3C2410_GPC3_VFRAME (0x02 << 6)
#define S3C2400_GPC3_VD3 (0x02 << 6)
-#define S3C2410_GPC4 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 4)
-#define S3C2410_GPC4_INP (0x00 << 8)
-#define S3C2410_GPC4_OUTP (0x01 << 8)
#define S3C2410_GPC4_VM (0x02 << 8)
#define S3C2400_GPC4_VD4 (0x02 << 8)
-#define S3C2410_GPC5 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 5)
-#define S3C2410_GPC5_INP (0x00 << 10)
-#define S3C2410_GPC5_OUTP (0x01 << 10)
#define S3C2410_GPC5_LCDVF0 (0x02 << 10)
#define S3C2400_GPC5_VD5 (0x02 << 10)
-#define S3C2410_GPC6 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 6)
-#define S3C2410_GPC6_INP (0x00 << 12)
-#define S3C2410_GPC6_OUTP (0x01 << 12)
#define S3C2410_GPC6_LCDVF1 (0x02 << 12)
#define S3C2400_GPC6_VD6 (0x02 << 12)
-#define S3C2410_GPC7 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 7)
-#define S3C2410_GPC7_INP (0x00 << 14)
-#define S3C2410_GPC7_OUTP (0x01 << 14)
#define S3C2410_GPC7_LCDVF2 (0x02 << 14)
#define S3C2400_GPC7_VD7 (0x02 << 14)
-#define S3C2410_GPC8 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 8)
-#define S3C2410_GPC8_INP (0x00 << 16)
-#define S3C2410_GPC8_OUTP (0x01 << 16)
#define S3C2410_GPC8_VD0 (0x02 << 16)
#define S3C2400_GPC8_VD8 (0x02 << 16)
-#define S3C2410_GPC9 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 9)
-#define S3C2410_GPC9_INP (0x00 << 18)
-#define S3C2410_GPC9_OUTP (0x01 << 18)
#define S3C2410_GPC9_VD1 (0x02 << 18)
#define S3C2400_GPC9_VD9 (0x02 << 18)
-#define S3C2410_GPC10 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 10)
-#define S3C2410_GPC10_INP (0x00 << 20)
-#define S3C2410_GPC10_OUTP (0x01 << 20)
#define S3C2410_GPC10_VD2 (0x02 << 20)
#define S3C2400_GPC10_VD10 (0x02 << 20)
-#define S3C2410_GPC11 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 11)
-#define S3C2410_GPC11_INP (0x00 << 22)
-#define S3C2410_GPC11_OUTP (0x01 << 22)
#define S3C2410_GPC11_VD3 (0x02 << 22)
#define S3C2400_GPC11_VD11 (0x02 << 22)
-#define S3C2410_GPC12 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 12)
-#define S3C2410_GPC12_INP (0x00 << 24)
-#define S3C2410_GPC12_OUTP (0x01 << 24)
#define S3C2410_GPC12_VD4 (0x02 << 24)
#define S3C2400_GPC12_VD12 (0x02 << 24)
-#define S3C2410_GPC13 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 13)
-#define S3C2410_GPC13_INP (0x00 << 26)
-#define S3C2410_GPC13_OUTP (0x01 << 26)
#define S3C2410_GPC13_VD5 (0x02 << 26)
#define S3C2400_GPC13_VD13 (0x02 << 26)
-#define S3C2410_GPC14 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 14)
-#define S3C2410_GPC14_INP (0x00 << 28)
-#define S3C2410_GPC14_OUTP (0x01 << 28)
#define S3C2410_GPC14_VD6 (0x02 << 28)
#define S3C2400_GPC14_VD14 (0x02 << 28)
-#define S3C2410_GPC15 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 15)
-#define S3C2410_GPC15_INP (0x00 << 30)
-#define S3C2410_GPC15_OUTP (0x01 << 30)
#define S3C2410_GPC15_VD7 (0x02 << 30)
#define S3C2400_GPC15_VD15 (0x02 << 30)
@@ -432,99 +300,51 @@
#define S3C2400_GPDDAT S3C2410_GPIOREG(0x24)
#define S3C2400_GPDUP S3C2410_GPIOREG(0x28)
-#define S3C2410_GPD0 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 0)
-#define S3C2410_GPD0_INP (0x00 << 0)
-#define S3C2410_GPD0_OUTP (0x01 << 0)
#define S3C2410_GPD0_VD8 (0x02 << 0)
#define S3C2400_GPD0_VFRAME (0x02 << 0)
#define S3C2442_GPD0_nSPICS1 (0x03 << 0)
-#define S3C2410_GPD1 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 1)
-#define S3C2410_GPD1_INP (0x00 << 2)
-#define S3C2410_GPD1_OUTP (0x01 << 2)
#define S3C2410_GPD1_VD9 (0x02 << 2)
#define S3C2400_GPD1_VM (0x02 << 2)
#define S3C2442_GPD1_SPICLK1 (0x03 << 2)
-#define S3C2410_GPD2 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 2)
-#define S3C2410_GPD2_INP (0x00 << 4)
-#define S3C2410_GPD2_OUTP (0x01 << 4)
#define S3C2410_GPD2_VD10 (0x02 << 4)
#define S3C2400_GPD2_VLINE (0x02 << 4)
-#define S3C2410_GPD3 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 3)
-#define S3C2410_GPD3_INP (0x00 << 6)
-#define S3C2410_GPD3_OUTP (0x01 << 6)
#define S3C2410_GPD3_VD11 (0x02 << 6)
#define S3C2400_GPD3_VCLK (0x02 << 6)
-#define S3C2410_GPD4 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 4)
-#define S3C2410_GPD4_INP (0x00 << 8)
-#define S3C2410_GPD4_OUTP (0x01 << 8)
#define S3C2410_GPD4_VD12 (0x02 << 8)
#define S3C2400_GPD4_LEND (0x02 << 8)
-#define S3C2410_GPD5 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 5)
-#define S3C2410_GPD5_INP (0x00 << 10)
-#define S3C2410_GPD5_OUTP (0x01 << 10)
#define S3C2410_GPD5_VD13 (0x02 << 10)
#define S3C2400_GPD5_TOUT0 (0x02 << 10)
-#define S3C2410_GPD6 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 6)
-#define S3C2410_GPD6_INP (0x00 << 12)
-#define S3C2410_GPD6_OUTP (0x01 << 12)
#define S3C2410_GPD6_VD14 (0x02 << 12)
#define S3C2400_GPD6_TOUT1 (0x02 << 12)
-#define S3C2410_GPD7 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 7)
-#define S3C2410_GPD7_INP (0x00 << 14)
-#define S3C2410_GPD7_OUTP (0x01 << 14)
#define S3C2410_GPD7_VD15 (0x02 << 14)
#define S3C2400_GPD7_TOUT2 (0x02 << 14)
-#define S3C2410_GPD8 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 8)
-#define S3C2410_GPD8_INP (0x00 << 16)
-#define S3C2410_GPD8_OUTP (0x01 << 16)
#define S3C2410_GPD8_VD16 (0x02 << 16)
#define S3C2400_GPD8_TOUT3 (0x02 << 16)
-#define S3C2410_GPD9 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 9)
-#define S3C2410_GPD9_INP (0x00 << 18)
-#define S3C2410_GPD9_OUTP (0x01 << 18)
#define S3C2410_GPD9_VD17 (0x02 << 18)
#define S3C2400_GPD9_TCLK0 (0x02 << 18)
#define S3C2410_GPD9_MASK (0x03 << 18)
-#define S3C2410_GPD10 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 10)
-#define S3C2410_GPD10_INP (0x00 << 20)
-#define S3C2410_GPD10_OUTP (0x01 << 20)
#define S3C2410_GPD10_VD18 (0x02 << 20)
#define S3C2400_GPD10_nWAIT (0x02 << 20)
-#define S3C2410_GPD11 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 11)
-#define S3C2410_GPD11_INP (0x00 << 22)
-#define S3C2410_GPD11_OUTP (0x01 << 22)
#define S3C2410_GPD11_VD19 (0x02 << 22)
-#define S3C2410_GPD12 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 12)
-#define S3C2410_GPD12_INP (0x00 << 24)
-#define S3C2410_GPD12_OUTP (0x01 << 24)
#define S3C2410_GPD12_VD20 (0x02 << 24)
-#define S3C2410_GPD13 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 13)
-#define S3C2410_GPD13_INP (0x00 << 26)
-#define S3C2410_GPD13_OUTP (0x01 << 26)
#define S3C2410_GPD13_VD21 (0x02 << 26)
-#define S3C2410_GPD14 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 14)
-#define S3C2410_GPD14_INP (0x00 << 28)
-#define S3C2410_GPD14_OUTP (0x01 << 28)
#define S3C2410_GPD14_VD22 (0x02 << 28)
#define S3C2410_GPD14_nSS1 (0x03 << 28)
-#define S3C2410_GPD15 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 15)
-#define S3C2410_GPD15_INP (0x00 << 30)
-#define S3C2410_GPD15_OUTP (0x01 << 30)
#define S3C2410_GPD15_VD23 (0x02 << 30)
#define S3C2410_GPD15_nSS0 (0x03 << 30)
@@ -550,34 +370,22 @@
#define S3C2400_GPEDAT S3C2410_GPIOREG(0x30)
#define S3C2400_GPEUP S3C2410_GPIOREG(0x34)
-#define S3C2410_GPE0 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 0)
-#define S3C2410_GPE0_INP (0x00 << 0)
-#define S3C2410_GPE0_OUTP (0x01 << 0)
#define S3C2410_GPE0_I2SLRCK (0x02 << 0)
#define S3C2443_GPE0_AC_nRESET (0x03 << 0)
#define S3C2400_GPE0_EINT0 (0x02 << 0)
#define S3C2410_GPE0_MASK (0x03 << 0)
-#define S3C2410_GPE1 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 1)
-#define S3C2410_GPE1_INP (0x00 << 2)
-#define S3C2410_GPE1_OUTP (0x01 << 2)
#define S3C2410_GPE1_I2SSCLK (0x02 << 2)
#define S3C2443_GPE1_AC_SYNC (0x03 << 2)
#define S3C2400_GPE1_EINT1 (0x02 << 2)
#define S3C2400_GPE1_nSS (0x03 << 2)
#define S3C2410_GPE1_MASK (0x03 << 2)
-#define S3C2410_GPE2 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 2)
-#define S3C2410_GPE2_INP (0x00 << 4)
-#define S3C2410_GPE2_OUTP (0x01 << 4)
#define S3C2410_GPE2_CDCLK (0x02 << 4)
#define S3C2443_GPE2_AC_BITCLK (0x03 << 4)
#define S3C2400_GPE2_EINT2 (0x02 << 4)
#define S3C2400_GPE2_I2SSDI (0x03 << 4)
-#define S3C2410_GPE3 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 3)
-#define S3C2410_GPE3_INP (0x00 << 6)
-#define S3C2410_GPE3_OUTP (0x01 << 6)
#define S3C2410_GPE3_I2SSDI (0x02 << 6)
#define S3C2443_GPE3_AC_SDI (0x03 << 6)
#define S3C2400_GPE3_EINT3 (0x02 << 6)
@@ -585,9 +393,6 @@
#define S3C2410_GPE3_nSS0 (0x03 << 6)
#define S3C2410_GPE3_MASK (0x03 << 6)
-#define S3C2410_GPE4 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 4)
-#define S3C2410_GPE4_INP (0x00 << 8)
-#define S3C2410_GPE4_OUTP (0x01 << 8)
#define S3C2410_GPE4_I2SSDO (0x02 << 8)
#define S3C2443_GPE4_AC_SDO (0x03 << 8)
#define S3C2400_GPE4_EINT4 (0x02 << 8)
@@ -595,81 +400,48 @@
#define S3C2410_GPE4_I2SSDI (0x03 << 8)
#define S3C2410_GPE4_MASK (0x03 << 8)
-#define S3C2410_GPE5 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 5)
-#define S3C2410_GPE5_INP (0x00 << 10)
-#define S3C2410_GPE5_OUTP (0x01 << 10)
#define S3C2410_GPE5_SDCLK (0x02 << 10)
#define S3C2443_GPE5_SD1_CLK (0x02 << 10)
#define S3C2400_GPE5_EINT5 (0x02 << 10)
#define S3C2400_GPE5_TCLK1 (0x03 << 10)
-#define S3C2410_GPE6 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 6)
-#define S3C2410_GPE6_INP (0x00 << 12)
-#define S3C2410_GPE6_OUTP (0x01 << 12)
#define S3C2410_GPE6_SDCMD (0x02 << 12)
#define S3C2443_GPE6_SD1_CMD (0x02 << 12)
#define S3C2443_GPE6_AC_BITCLK (0x03 << 12)
#define S3C2400_GPE6_EINT6 (0x02 << 12)
-#define S3C2410_GPE7 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 7)
-#define S3C2410_GPE7_INP (0x00 << 14)
-#define S3C2410_GPE7_OUTP (0x01 << 14)
#define S3C2410_GPE7_SDDAT0 (0x02 << 14)
#define S3C2443_GPE5_SD1_DAT0 (0x02 << 14)
#define S3C2443_GPE7_AC_SDI (0x03 << 14)
#define S3C2400_GPE7_EINT7 (0x02 << 14)
-#define S3C2410_GPE8 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 8)
-#define S3C2410_GPE8_INP (0x00 << 16)
-#define S3C2410_GPE8_OUTP (0x01 << 16)
#define S3C2410_GPE8_SDDAT1 (0x02 << 16)
#define S3C2443_GPE8_SD1_DAT1 (0x02 << 16)
#define S3C2443_GPE8_AC_SDO (0x03 << 16)
#define S3C2400_GPE8_nXDACK0 (0x02 << 16)
-#define S3C2410_GPE9 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 9)
-#define S3C2410_GPE9_INP (0x00 << 18)
-#define S3C2410_GPE9_OUTP (0x01 << 18)
#define S3C2410_GPE9_SDDAT2 (0x02 << 18)
#define S3C2443_GPE9_SD1_DAT2 (0x02 << 18)
#define S3C2443_GPE9_AC_SYNC (0x03 << 18)
#define S3C2400_GPE9_nXDACK1 (0x02 << 18)
#define S3C2400_GPE9_nXBACK (0x03 << 18)
-#define S3C2410_GPE10 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 10)
-#define S3C2410_GPE10_INP (0x00 << 20)
-#define S3C2410_GPE10_OUTP (0x01 << 20)
#define S3C2410_GPE10_SDDAT3 (0x02 << 20)
#define S3C2443_GPE10_SD1_DAT3 (0x02 << 20)
#define S3C2443_GPE10_AC_nRESET (0x03 << 20)
#define S3C2400_GPE10_nXDREQ0 (0x02 << 20)
-#define S3C2410_GPE11 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 11)
-#define S3C2410_GPE11_INP (0x00 << 22)
-#define S3C2410_GPE11_OUTP (0x01 << 22)
#define S3C2410_GPE11_SPIMISO0 (0x02 << 22)
#define S3C2400_GPE11_nXDREQ1 (0x02 << 22)
#define S3C2400_GPE11_nXBREQ (0x03 << 22)
-#define S3C2410_GPE12 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 12)
-#define S3C2410_GPE12_INP (0x00 << 24)
-#define S3C2410_GPE12_OUTP (0x01 << 24)
#define S3C2410_GPE12_SPIMOSI0 (0x02 << 24)
-#define S3C2410_GPE13 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 13)
-#define S3C2410_GPE13_INP (0x00 << 26)
-#define S3C2410_GPE13_OUTP (0x01 << 26)
#define S3C2410_GPE13_SPICLK0 (0x02 << 26)
-#define S3C2410_GPE14 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 14)
-#define S3C2410_GPE14_INP (0x00 << 28)
-#define S3C2410_GPE14_OUTP (0x01 << 28)
#define S3C2410_GPE14_IICSCL (0x02 << 28)
#define S3C2410_GPE14_MASK (0x03 << 28)
-#define S3C2410_GPE15 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 15)
-#define S3C2410_GPE15_INP (0x00 << 30)
-#define S3C2410_GPE15_OUTP (0x01 << 30)
#define S3C2410_GPE15_IICSDA (0x02 << 30)
#define S3C2410_GPE15_MASK (0x03 << 30)
@@ -705,55 +477,31 @@
#define S3C2400_GPFDAT S3C2410_GPIOREG(0x3C)
#define S3C2400_GPFUP S3C2410_GPIOREG(0x40)
-#define S3C2410_GPF0 S3C2410_GPIONO(S3C2410_GPIO_BANKF, 0)
-#define S3C2410_GPF0_INP (0x00 << 0)
-#define S3C2410_GPF0_OUTP (0x01 << 0)
#define S3C2410_GPF0_EINT0 (0x02 << 0)
#define S3C2400_GPF0_RXD0 (0x02 << 0)
-#define S3C2410_GPF1 S3C2410_GPIONO(S3C2410_GPIO_BANKF, 1)
-#define S3C2410_GPF1_INP (0x00 << 2)
-#define S3C2410_GPF1_OUTP (0x01 << 2)
#define S3C2410_GPF1_EINT1 (0x02 << 2)
#define S3C2400_GPF1_RXD1 (0x02 << 2)
#define S3C2400_GPF1_IICSDA (0x03 << 2)
-#define S3C2410_GPF2 S3C2410_GPIONO(S3C2410_GPIO_BANKF, 2)
-#define S3C2410_GPF2_INP (0x00 << 4)
-#define S3C2410_GPF2_OUTP (0x01 << 4)
#define S3C2410_GPF2_EINT2 (0x02 << 4)
#define S3C2400_GPF2_TXD0 (0x02 << 4)
-#define S3C2410_GPF3 S3C2410_GPIONO(S3C2410_GPIO_BANKF, 3)
-#define S3C2410_GPF3_INP (0x00 << 6)
-#define S3C2410_GPF3_OUTP (0x01 << 6)
#define S3C2410_GPF3_EINT3 (0x02 << 6)
#define S3C2400_GPF3_TXD1 (0x02 << 6)
#define S3C2400_GPF3_IICSCL (0x03 << 6)
-#define S3C2410_GPF4 S3C2410_GPIONO(S3C2410_GPIO_BANKF, 4)
-#define S3C2410_GPF4_INP (0x00 << 8)
-#define S3C2410_GPF4_OUTP (0x01 << 8)
#define S3C2410_GPF4_EINT4 (0x02 << 8)
#define S3C2400_GPF4_nRTS0 (0x02 << 8)
#define S3C2400_GPF4_nXBACK (0x03 << 8)
-#define S3C2410_GPF5 S3C2410_GPIONO(S3C2410_GPIO_BANKF, 5)
-#define S3C2410_GPF5_INP (0x00 << 10)
-#define S3C2410_GPF5_OUTP (0x01 << 10)
#define S3C2410_GPF5_EINT5 (0x02 << 10)
#define S3C2400_GPF5_nCTS0 (0x02 << 10)
#define S3C2400_GPF5_nXBREQ (0x03 << 10)
-#define S3C2410_GPF6 S3C2410_GPIONO(S3C2410_GPIO_BANKF, 6)
-#define S3C2410_GPF6_INP (0x00 << 12)
-#define S3C2410_GPF6_OUTP (0x01 << 12)
#define S3C2410_GPF6_EINT6 (0x02 << 12)
#define S3C2400_GPF6_CLKOUT (0x02 << 12)
-#define S3C2410_GPF7 S3C2410_GPIONO(S3C2410_GPIO_BANKF, 7)
-#define S3C2410_GPF7_INP (0x00 << 14)
-#define S3C2410_GPF7_OUTP (0x01 << 14)
#define S3C2410_GPF7_EINT7 (0x02 << 14)
#define S3C2410_GPF_PUPDIS(x) (1<<(x))
@@ -778,117 +526,69 @@
#define S3C2400_GPGDAT S3C2410_GPIOREG(0x48)
#define S3C2400_GPGUP S3C2410_GPIOREG(0x4C)
-#define S3C2410_GPG0 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 0)
-#define S3C2410_GPG0_INP (0x00 << 0)
-#define S3C2410_GPG0_OUTP (0x01 << 0)
#define S3C2410_GPG0_EINT8 (0x02 << 0)
#define S3C2400_GPG0_I2SLRCK (0x02 << 0)
-#define S3C2410_GPG1 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 1)
-#define S3C2410_GPG1_INP (0x00 << 2)
-#define S3C2410_GPG1_OUTP (0x01 << 2)
#define S3C2410_GPG1_EINT9 (0x02 << 2)
#define S3C2400_GPG1_I2SSCLK (0x02 << 2)
-#define S3C2410_GPG2 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 2)
-#define S3C2410_GPG2_INP (0x00 << 4)
-#define S3C2410_GPG2_OUTP (0x01 << 4)
#define S3C2410_GPG2_EINT10 (0x02 << 4)
#define S3C2410_GPG2_nSS0 (0x03 << 4)
#define S3C2400_GPG2_CDCLK (0x02 << 4)
-#define S3C2410_GPG3 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 3)
-#define S3C2410_GPG3_INP (0x00 << 6)
-#define S3C2410_GPG3_OUTP (0x01 << 6)
#define S3C2410_GPG3_EINT11 (0x02 << 6)
#define S3C2410_GPG3_nSS1 (0x03 << 6)
#define S3C2400_GPG3_I2SSDO (0x02 << 6)
#define S3C2400_GPG3_I2SSDI (0x03 << 6)
-#define S3C2410_GPG4 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 4)
-#define S3C2410_GPG4_INP (0x00 << 8)
-#define S3C2410_GPG4_OUTP (0x01 << 8)
#define S3C2410_GPG4_EINT12 (0x02 << 8)
#define S3C2400_GPG4_MMCCLK (0x02 << 8)
#define S3C2400_GPG4_I2SSDI (0x03 << 8)
#define S3C2410_GPG4_LCDPWREN (0x03 << 8)
#define S3C2443_GPG4_LCDPWRDN (0x03 << 8)
-#define S3C2410_GPG5 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 5)
-#define S3C2410_GPG5_INP (0x00 << 10)
-#define S3C2410_GPG5_OUTP (0x01 << 10)
#define S3C2410_GPG5_EINT13 (0x02 << 10)
#define S3C2400_GPG5_MMCCMD (0x02 << 10)
#define S3C2400_GPG5_IICSDA (0x03 << 10)
#define S3C2410_GPG5_SPIMISO1 (0x03 << 10) /* not s3c2443 */
-#define S3C2410_GPG6 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 6)
-#define S3C2410_GPG6_INP (0x00 << 12)
-#define S3C2410_GPG6_OUTP (0x01 << 12)
#define S3C2410_GPG6_EINT14 (0x02 << 12)
#define S3C2400_GPG6_MMCDAT (0x02 << 12)
#define S3C2400_GPG6_IICSCL (0x03 << 12)
#define S3C2410_GPG6_SPIMOSI1 (0x03 << 12)
-#define S3C2410_GPG7 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 7)
-#define S3C2410_GPG7_INP (0x00 << 14)
-#define S3C2410_GPG7_OUTP (0x01 << 14)
#define S3C2410_GPG7_EINT15 (0x02 << 14)
#define S3C2410_GPG7_SPICLK1 (0x03 << 14)
#define S3C2400_GPG7_SPIMISO (0x02 << 14)
#define S3C2400_GPG7_IICSDA (0x03 << 14)
-#define S3C2410_GPG8 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 8)
-#define S3C2410_GPG8_INP (0x00 << 16)
-#define S3C2410_GPG8_OUTP (0x01 << 16)
#define S3C2410_GPG8_EINT16 (0x02 << 16)
#define S3C2400_GPG8_SPIMOSI (0x02 << 16)
#define S3C2400_GPG8_IICSCL (0x03 << 16)
-#define S3C2410_GPG9 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 9)
-#define S3C2410_GPG9_INP (0x00 << 18)
-#define S3C2410_GPG9_OUTP (0x01 << 18)
#define S3C2410_GPG9_EINT17 (0x02 << 18)
#define S3C2400_GPG9_SPICLK (0x02 << 18)
#define S3C2400_GPG9_MMCCLK (0x03 << 18)
-#define S3C2410_GPG10 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 10)
-#define S3C2410_GPG10_INP (0x00 << 20)
-#define S3C2410_GPG10_OUTP (0x01 << 20)
#define S3C2410_GPG10_EINT18 (0x02 << 20)
-#define S3C2410_GPG11 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 11)
-#define S3C2410_GPG11_INP (0x00 << 22)
-#define S3C2410_GPG11_OUTP (0x01 << 22)
#define S3C2410_GPG11_EINT19 (0x02 << 22)
#define S3C2410_GPG11_TCLK1 (0x03 << 22)
#define S3C2443_GPG11_CF_nIREQ (0x03 << 22)
-#define S3C2410_GPG12 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 12)
-#define S3C2410_GPG12_INP (0x00 << 24)
-#define S3C2410_GPG12_OUTP (0x01 << 24)
#define S3C2410_GPG12_EINT20 (0x02 << 24)
#define S3C2410_GPG12_XMON (0x03 << 24)
#define S3C2442_GPG12_nSPICS0 (0x03 << 24)
#define S3C2443_GPG12_nINPACK (0x03 << 24)
-#define S3C2410_GPG13 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 13)
-#define S3C2410_GPG13_INP (0x00 << 26)
-#define S3C2410_GPG13_OUTP (0x01 << 26)
#define S3C2410_GPG13_EINT21 (0x02 << 26)
#define S3C2410_GPG13_nXPON (0x03 << 26)
#define S3C2443_GPG13_CF_nREG (0x03 << 26)
-#define S3C2410_GPG14 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 14)
-#define S3C2410_GPG14_INP (0x00 << 28)
-#define S3C2410_GPG14_OUTP (0x01 << 28)
#define S3C2410_GPG14_EINT22 (0x02 << 28)
#define S3C2410_GPG14_YMON (0x03 << 28)
#define S3C2443_GPG14_CF_RESET (0x03 << 28)
-#define S3C2410_GPG15 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 15)
-#define S3C2410_GPG15_INP (0x00 << 30)
-#define S3C2410_GPG15_OUTP (0x01 << 30)
#define S3C2410_GPG15_EINT23 (0x02 << 30)
#define S3C2410_GPG15_nYPON (0x03 << 30)
#define S3C2443_GPG15_CF_PWR (0x03 << 30)
@@ -907,62 +607,29 @@
#define S3C2410_GPHDAT S3C2410_GPIOREG(0x74)
#define S3C2410_GPHUP S3C2410_GPIOREG(0x78)
-#define S3C2410_GPH0 S3C2410_GPIONO(S3C2410_GPIO_BANKH, 0)
-#define S3C2410_GPH0_INP (0x00 << 0)
-#define S3C2410_GPH0_OUTP (0x01 << 0)
#define S3C2410_GPH0_nCTS0 (0x02 << 0)
-#define S3C2410_GPH1 S3C2410_GPIONO(S3C2410_GPIO_BANKH, 1)
-#define S3C2410_GPH1_INP (0x00 << 2)
-#define S3C2410_GPH1_OUTP (0x01 << 2)
#define S3C2410_GPH1_nRTS0 (0x02 << 2)
-#define S3C2410_GPH2 S3C2410_GPIONO(S3C2410_GPIO_BANKH, 2)
-#define S3C2410_GPH2_INP (0x00 << 4)
-#define S3C2410_GPH2_OUTP (0x01 << 4)
#define S3C2410_GPH2_TXD0 (0x02 << 4)
-#define S3C2410_GPH3 S3C2410_GPIONO(S3C2410_GPIO_BANKH, 3)
-#define S3C2410_GPH3_INP (0x00 << 6)
-#define S3C2410_GPH3_OUTP (0x01 << 6)
#define S3C2410_GPH3_RXD0 (0x02 << 6)
-#define S3C2410_GPH4 S3C2410_GPIONO(S3C2410_GPIO_BANKH, 4)
-#define S3C2410_GPH4_INP (0x00 << 8)
-#define S3C2410_GPH4_OUTP (0x01 << 8)
#define S3C2410_GPH4_TXD1 (0x02 << 8)
-#define S3C2410_GPH5 S3C2410_GPIONO(S3C2410_GPIO_BANKH, 5)
-#define S3C2410_GPH5_INP (0x00 << 10)
-#define S3C2410_GPH5_OUTP (0x01 << 10)
#define S3C2410_GPH5_RXD1 (0x02 << 10)
-#define S3C2410_GPH6 S3C2410_GPIONO(S3C2410_GPIO_BANKH, 6)
-#define S3C2410_GPH6_INP (0x00 << 12)
-#define S3C2410_GPH6_OUTP (0x01 << 12)
#define S3C2410_GPH6_TXD2 (0x02 << 12)
#define S3C2410_GPH6_nRTS1 (0x03 << 12)
-#define S3C2410_GPH7 S3C2410_GPIONO(S3C2410_GPIO_BANKH, 7)
-#define S3C2410_GPH7_INP (0x00 << 14)
-#define S3C2410_GPH7_OUTP (0x01 << 14)
#define S3C2410_GPH7_RXD2 (0x02 << 14)
#define S3C2410_GPH7_nCTS1 (0x03 << 14)
-#define S3C2410_GPH8 S3C2410_GPIONO(S3C2410_GPIO_BANKH, 8)
-#define S3C2410_GPH8_INP (0x00 << 16)
-#define S3C2410_GPH8_OUTP (0x01 << 16)
#define S3C2410_GPH8_UCLK (0x02 << 16)
-#define S3C2410_GPH9 S3C2410_GPIONO(S3C2410_GPIO_BANKH, 9)
-#define S3C2410_GPH9_INP (0x00 << 18)
-#define S3C2410_GPH9_OUTP (0x01 << 18)
#define S3C2410_GPH9_CLKOUT0 (0x02 << 18)
#define S3C2442_GPH9_nSPICS0 (0x03 << 18)
-#define S3C2410_GPH10 S3C2410_GPIONO(S3C2410_GPIO_BANKH, 10)
-#define S3C2410_GPH10_INP (0x00 << 20)
-#define S3C2410_GPH10_OUTP (0x01 << 20)
#define S3C2410_GPH10_CLKOUT1 (0x02 << 20)
/* The S3C2412 and S3C2413 move the GPJ register set to after
diff --git a/arch/arm/mach-s3c2410/include/mach/system-reset.h b/arch/arm/mach-s3c2410/include/mach/system-reset.h
index b8687f7..6faadce 100644
--- a/arch/arm/mach-s3c2410/include/mach/system-reset.h
+++ b/arch/arm/mach-s3c2410/include/mach/system-reset.h
@@ -11,21 +11,13 @@
*/
#include <mach/hardware.h>
-#include <linux/io.h>
-
-#include <plat/regs-watchdog.h>
-#include <mach/regs-clock.h>
-
-#include <linux/clk.h>
-#include <linux/err.h>
+#include <plat/watchdog-reset.h>
extern void (*s3c24xx_reset_hook)(void);
static void
arch_reset(char mode, const char *cmd)
{
- struct clk *wdtclk;
-
if (mode == 's') {
cpu_reset(0);
}
@@ -33,31 +25,7 @@
if (s3c24xx_reset_hook)
s3c24xx_reset_hook();
- printk("arch_reset: attempting watchdog reset\n");
-
- __raw_writel(0, S3C2410_WTCON); /* disable watchdog, to be safe */
-
- wdtclk = clk_get(NULL, "watchdog");
- if (!IS_ERR(wdtclk)) {
- clk_enable(wdtclk);
- } else
- printk(KERN_WARNING "%s: warning: cannot get watchdog clock\n", __func__);
-
- /* put initial values into count and data */
- __raw_writel(0x80, S3C2410_WTCNT);
- __raw_writel(0x80, S3C2410_WTDAT);
-
- /* set the watchdog to go and reset... */
- __raw_writel(S3C2410_WTCON_ENABLE|S3C2410_WTCON_DIV16|S3C2410_WTCON_RSTEN |
- S3C2410_WTCON_PRESCALE(0x20), S3C2410_WTCON);
-
- /* wait for reset to assert... */
- mdelay(500);
-
- printk(KERN_ERR "Watchdog reset failed to assert reset\n");
-
- /* delay to allow the serial port to show the message */
- mdelay(50);
+ arch_wdt_reset();
/* we'll take a jump through zero as a poor second */
cpu_reset(0);
diff --git a/arch/arm/mach-s3c2410/mach-amlm5900.c b/arch/arm/mach-s3c2410/mach-amlm5900.c
index 6d6995a..06a84ad 100644
--- a/arch/arm/mach-s3c2410/mach-amlm5900.c
+++ b/arch/arm/mach-s3c2410/mach-amlm5900.c
@@ -32,6 +32,7 @@
#include <linux/list.h>
#include <linux/timer.h>
#include <linux/init.h>
+#include <linux/gpio.h>
#include <linux/device.h>
#include <linux/platform_device.h>
#include <linux/proc_fs.h>
@@ -224,8 +225,8 @@
} else {
enable_irq_wake(IRQ_EINT9);
/* configure the suspend/resume status pin */
- s3c2410_gpio_cfgpin(S3C2410_GPF2, S3C2410_GPF2_OUTP);
- s3c2410_gpio_pullup(S3C2410_GPF2, 0);
+ s3c2410_gpio_cfgpin(S3C2410_GPF(2), S3C2410_GPIO_OUTPUT);
+ s3c2410_gpio_pullup(S3C2410_GPF(2), 0);
}
}
static void __init amlm5900_init(void)
diff --git a/arch/arm/mach-s3c2410/mach-bast.c b/arch/arm/mach-s3c2410/mach-bast.c
index 8637dea..ce3baba2 100644
--- a/arch/arm/mach-s3c2410/mach-bast.c
+++ b/arch/arm/mach-s3c2410/mach-bast.c
@@ -16,6 +16,7 @@
#include <linux/list.h>
#include <linux/timer.h>
#include <linux/init.h>
+#include <linux/gpio.h>
#include <linux/sysdev.h>
#include <linux/serial_core.h>
#include <linux/platform_device.h>
@@ -212,15 +213,15 @@
static int bast_pm_suspend(struct sys_device *sd, pm_message_t state)
{
/* ensure that an nRESET is not generated on resume. */
- s3c2410_gpio_setpin(S3C2410_GPA21, 1);
- s3c2410_gpio_cfgpin(S3C2410_GPA21, S3C2410_GPA21_OUT);
+ s3c2410_gpio_setpin(S3C2410_GPA(21), 1);
+ s3c2410_gpio_cfgpin(S3C2410_GPA(21), S3C2410_GPIO_OUTPUT);
return 0;
}
static int bast_pm_resume(struct sys_device *sd)
{
- s3c2410_gpio_cfgpin(S3C2410_GPA21, S3C2410_GPA21_nRSTOUT);
+ s3c2410_gpio_cfgpin(S3C2410_GPA(21), S3C2410_GPA21_nRSTOUT);
return 0;
}
@@ -591,8 +592,6 @@
s3c24xx_init_io(bast_iodesc, ARRAY_SIZE(bast_iodesc));
s3c24xx_init_clocks(0);
s3c24xx_init_uarts(bast_uartcfgs, ARRAY_SIZE(bast_uartcfgs));
-
- usb_simtec_init();
}
static void __init bast_init(void)
@@ -607,6 +606,7 @@
i2c_register_board_info(0, bast_i2c_devs,
ARRAY_SIZE(bast_i2c_devs));
+ usb_simtec_init();
nor_simtec_init();
}
diff --git a/arch/arm/mach-s3c2410/mach-h1940.c b/arch/arm/mach-s3c2410/mach-h1940.c
index 7a7c4da..d9cd5dd 100644
--- a/arch/arm/mach-s3c2410/mach-h1940.c
+++ b/arch/arm/mach-s3c2410/mach-h1940.c
@@ -127,7 +127,7 @@
static struct s3c2410_udc_mach_info h1940_udc_cfg __initdata = {
.udc_command = h1940_udc_pullup,
- .vbus_pin = S3C2410_GPG5,
+ .vbus_pin = S3C2410_GPG(5),
.vbus_pin_inverted = 1,
};
diff --git a/arch/arm/mach-s3c2410/mach-n30.c b/arch/arm/mach-s3c2410/mach-n30.c
index 2b83f87..0f6ed61 100644
--- a/arch/arm/mach-s3c2410/mach-n30.c
+++ b/arch/arm/mach-s3c2410/mach-n30.c
@@ -19,6 +19,7 @@
#include <linux/gpio_keys.h>
#include <linux/init.h>
+#include <linux/gpio.h>
#include <linux/input.h>
#include <linux/interrupt.h>
#include <linux/platform_device.h>
@@ -85,10 +86,10 @@
{
switch (cmd) {
case S3C2410_UDC_P_ENABLE :
- s3c2410_gpio_setpin(S3C2410_GPB3, 1);
+ s3c2410_gpio_setpin(S3C2410_GPB(3), 1);
break;
case S3C2410_UDC_P_DISABLE :
- s3c2410_gpio_setpin(S3C2410_GPB3, 0);
+ s3c2410_gpio_setpin(S3C2410_GPB(3), 0);
break;
case S3C2410_UDC_P_RESET :
break;
@@ -99,55 +100,55 @@
static struct s3c2410_udc_mach_info n30_udc_cfg __initdata = {
.udc_command = n30_udc_pullup,
- .vbus_pin = S3C2410_GPG1,
+ .vbus_pin = S3C2410_GPG(1),
.vbus_pin_inverted = 0,
};
static struct gpio_keys_button n30_buttons[] = {
{
- .gpio = S3C2410_GPF0,
+ .gpio = S3C2410_GPF(0),
.code = KEY_POWER,
.desc = "Power",
.active_low = 0,
},
{
- .gpio = S3C2410_GPG9,
+ .gpio = S3C2410_GPG(9),
.code = KEY_UP,
.desc = "Thumbwheel Up",
.active_low = 0,
},
{
- .gpio = S3C2410_GPG8,
+ .gpio = S3C2410_GPG(8),
.code = KEY_DOWN,
.desc = "Thumbwheel Down",
.active_low = 0,
},
{
- .gpio = S3C2410_GPG7,
+ .gpio = S3C2410_GPG(7),
.code = KEY_ENTER,
.desc = "Thumbwheel Press",
.active_low = 0,
},
{
- .gpio = S3C2410_GPF7,
+ .gpio = S3C2410_GPF(7),
.code = KEY_HOMEPAGE,
.desc = "Home",
.active_low = 0,
},
{
- .gpio = S3C2410_GPF6,
+ .gpio = S3C2410_GPF(6),
.code = KEY_CALENDAR,
.desc = "Calendar",
.active_low = 0,
},
{
- .gpio = S3C2410_GPF5,
+ .gpio = S3C2410_GPF(5),
.code = KEY_ADDRESSBOOK,
.desc = "Contacts",
.active_low = 0,
},
{
- .gpio = S3C2410_GPF4,
+ .gpio = S3C2410_GPF(4),
.code = KEY_MAIL,
.desc = "Mail",
.active_low = 0,
@@ -169,73 +170,73 @@
static struct gpio_keys_button n35_buttons[] = {
{
- .gpio = S3C2410_GPF0,
+ .gpio = S3C2410_GPF(0),
.code = KEY_POWER,
.desc = "Power",
.active_low = 0,
},
{
- .gpio = S3C2410_GPG9,
+ .gpio = S3C2410_GPG(9),
.code = KEY_UP,
.desc = "Joystick Up",
.active_low = 0,
},
{
- .gpio = S3C2410_GPG8,
+ .gpio = S3C2410_GPG(8),
.code = KEY_DOWN,
.desc = "Joystick Down",
.active_low = 0,
},
{
- .gpio = S3C2410_GPG6,
+ .gpio = S3C2410_GPG(6),
.code = KEY_DOWN,
.desc = "Joystick Left",
.active_low = 0,
},
{
- .gpio = S3C2410_GPG5,
+ .gpio = S3C2410_GPG(5),
.code = KEY_DOWN,
.desc = "Joystick Right",
.active_low = 0,
},
{
- .gpio = S3C2410_GPG7,
+ .gpio = S3C2410_GPG(7),
.code = KEY_ENTER,
.desc = "Joystick Press",
.active_low = 0,
},
{
- .gpio = S3C2410_GPF7,
+ .gpio = S3C2410_GPF(7),
.code = KEY_HOMEPAGE,
.desc = "Home",
.active_low = 0,
},
{
- .gpio = S3C2410_GPF6,
+ .gpio = S3C2410_GPF(6),
.code = KEY_CALENDAR,
.desc = "Calendar",
.active_low = 0,
},
{
- .gpio = S3C2410_GPF5,
+ .gpio = S3C2410_GPF(5),
.code = KEY_ADDRESSBOOK,
.desc = "Contacts",
.active_low = 0,
},
{
- .gpio = S3C2410_GPF4,
+ .gpio = S3C2410_GPF(4),
.code = KEY_MAIL,
.desc = "Mail",
.active_low = 0,
},
{
- .gpio = S3C2410_GPF3,
+ .gpio = S3C2410_GPF(3),
.code = SW_RADIO,
.desc = "GPS Antenna",
.active_low = 0,
},
{
- .gpio = S3C2410_GPG2,
+ .gpio = S3C2410_GPG(2),
.code = SW_HEADPHONE_INSERT,
.desc = "Headphone",
.active_low = 0,
@@ -259,7 +260,7 @@
/* This is the bluetooth LED on the device. */
static struct s3c24xx_led_platdata n30_blue_led_pdata = {
.name = "blue_led",
- .gpio = S3C2410_GPG6,
+ .gpio = S3C2410_GPG(6),
.def_trigger = "",
};
@@ -270,7 +271,7 @@
static struct s3c24xx_led_platdata n30_warning_led_pdata = {
.name = "warning_led",
.flags = S3C24XX_LEDF_ACTLOW,
- .gpio = S3C2410_GPD9,
+ .gpio = S3C2410_GPD(9),
.def_trigger = "",
};
diff --git a/arch/arm/mach-s3c2410/mach-qt2410.c b/arch/arm/mach-s3c2410/mach-qt2410.c
index 9f1ba9b..2cc9849 100644
--- a/arch/arm/mach-s3c2410/mach-qt2410.c
+++ b/arch/arm/mach-s3c2410/mach-qt2410.c
@@ -27,6 +27,7 @@
#include <linux/list.h>
#include <linux/timer.h>
#include <linux/init.h>
+#include <linux/gpio.h>
#include <linux/sysdev.h>
#include <linux/platform_device.h>
#include <linux/serial_core.h>
@@ -198,7 +199,7 @@
/* LED */
static struct s3c24xx_led_platdata qt2410_pdata_led = {
- .gpio = S3C2410_GPB0,
+ .gpio = S3C2410_GPB(0),
.flags = S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE,
.name = "led",
.def_trigger = "timer",
@@ -218,18 +219,18 @@
{
switch (cs) {
case BITBANG_CS_ACTIVE:
- s3c2410_gpio_setpin(S3C2410_GPB5, 0);
+ s3c2410_gpio_setpin(S3C2410_GPB(5), 0);
break;
case BITBANG_CS_INACTIVE:
- s3c2410_gpio_setpin(S3C2410_GPB5, 1);
+ s3c2410_gpio_setpin(S3C2410_GPB(5), 1);
break;
}
}
static struct s3c2410_spigpio_info spi_gpio_cfg = {
- .pin_clk = S3C2410_GPG7,
- .pin_mosi = S3C2410_GPG6,
- .pin_miso = S3C2410_GPG5,
+ .pin_clk = S3C2410_GPG(7),
+ .pin_mosi = S3C2410_GPG(6),
+ .pin_miso = S3C2410_GPG(5),
.chip_select = &spi_gpio_cs,
};
@@ -346,13 +347,13 @@
}
s3c24xx_fb_set_platdata(&qt2410_fb_info);
- s3c2410_gpio_cfgpin(S3C2410_GPB0, S3C2410_GPIO_OUTPUT);
- s3c2410_gpio_setpin(S3C2410_GPB0, 1);
+ s3c2410_gpio_cfgpin(S3C2410_GPB(0), S3C2410_GPIO_OUTPUT);
+ s3c2410_gpio_setpin(S3C2410_GPB(0), 1);
s3c24xx_udc_set_platdata(&qt2410_udc_cfg);
s3c_i2c0_set_platdata(NULL);
- s3c2410_gpio_cfgpin(S3C2410_GPB5, S3C2410_GPIO_OUTPUT);
+ s3c2410_gpio_cfgpin(S3C2410_GPB(5), S3C2410_GPIO_OUTPUT);
platform_add_devices(qt2410_devices, ARRAY_SIZE(qt2410_devices));
s3c_pm_init();
diff --git a/arch/arm/mach-s3c2410/mach-vr1000.c b/arch/arm/mach-s3c2410/mach-vr1000.c
index 61a1ea9..1628cc7 100644
--- a/arch/arm/mach-s3c2410/mach-vr1000.c
+++ b/arch/arm/mach-s3c2410/mach-vr1000.c
@@ -18,6 +18,7 @@
#include <linux/list.h>
#include <linux/timer.h>
#include <linux/init.h>
+#include <linux/gpio.h>
#include <linux/dm9000.h>
#include <linux/i2c.h>
@@ -277,19 +278,19 @@
static struct s3c24xx_led_platdata vr1000_led1_pdata = {
.name = "led1",
- .gpio = S3C2410_GPB0,
+ .gpio = S3C2410_GPB(0),
.def_trigger = "",
};
static struct s3c24xx_led_platdata vr1000_led2_pdata = {
.name = "led2",
- .gpio = S3C2410_GPB1,
+ .gpio = S3C2410_GPB(1),
.def_trigger = "",
};
static struct s3c24xx_led_platdata vr1000_led3_pdata = {
.name = "led3",
- .gpio = S3C2410_GPB2,
+ .gpio = S3C2410_GPB(2),
.def_trigger = "",
};
@@ -355,8 +356,8 @@
static void vr1000_power_off(void)
{
- s3c2410_gpio_cfgpin(S3C2410_GPB9, S3C2410_GPB9_OUTP);
- s3c2410_gpio_setpin(S3C2410_GPB9, 1);
+ s3c2410_gpio_cfgpin(S3C2410_GPB(9), S3C2410_GPIO_OUTPUT);
+ s3c2410_gpio_setpin(S3C2410_GPB(9), 1);
}
static void __init vr1000_map_io(void)
diff --git a/arch/arm/mach-s3c2410/pm.c b/arch/arm/mach-s3c2410/pm.c
index 87fc481..143e08a 100644
--- a/arch/arm/mach-s3c2410/pm.c
+++ b/arch/arm/mach-s3c2410/pm.c
@@ -25,6 +25,7 @@
#include <linux/errno.h>
#include <linux/time.h>
#include <linux/sysdev.h>
+#include <linux/gpio.h>
#include <linux/io.h>
#include <mach/hardware.h>
@@ -76,7 +77,7 @@
}
if ( machine_is_aml_m5900() )
- s3c2410_gpio_setpin(S3C2410_GPF2, 1);
+ s3c2410_gpio_setpin(S3C2410_GPF(2), 1);
}
@@ -91,7 +92,7 @@
__raw_writel(tmp, S3C2410_GSTATUS2);
if ( machine_is_aml_m5900() )
- s3c2410_gpio_setpin(S3C2410_GPF2, 0);
+ s3c2410_gpio_setpin(S3C2410_GPF(2), 0);
return 0;
}
diff --git a/arch/arm/mach-s3c2410/usb-simtec.c b/arch/arm/mach-s3c2410/usb-simtec.c
index 8331e8d..6cd9377 100644
--- a/arch/arm/mach-s3c2410/usb-simtec.c
+++ b/arch/arm/mach-s3c2410/usb-simtec.c
@@ -18,9 +18,11 @@
#include <linux/types.h>
#include <linux/interrupt.h>
#include <linux/list.h>
+#include <linux/gpio.h>
#include <linux/timer.h>
#include <linux/init.h>
#include <linux/device.h>
+#include <linux/gpio.h>
#include <linux/io.h>
#include <asm/mach/arch.h>
@@ -29,7 +31,6 @@
#include <mach/bast-map.h>
#include <mach/bast-irq.h>
-#include <mach/regs-gpio.h>
#include <mach/hardware.h>
#include <asm/irq.h>
@@ -53,9 +54,9 @@
power_state[port] = to;
if (power_state[0] && power_state[1])
- s3c2410_gpio_setpin(S3C2410_GPB4, 0);
+ gpio_set_value(S3C2410_GPB(4), 0);
else
- s3c2410_gpio_setpin(S3C2410_GPB4, 1);
+ gpio_set_value(S3C2410_GPB(4), 1);
}
static irqreturn_t
@@ -63,7 +64,7 @@
{
struct s3c2410_hcd_info *info = pw;
- if (s3c2410_gpio_getpin(S3C2410_GPG10) == 0) {
+ if (gpio_get_value(S3C2410_GPG(10)) == 0) {
pr_debug("usb_simtec: over-current irq (oc detected)\n");
s3c2410_usb_report_oc(info, 3);
} else {
@@ -106,10 +107,27 @@
int usb_simtec_init(void)
{
- printk("USB Power Control, (c) 2004 Simtec Electronics\n");
- s3c_device_usb.dev.platform_data = &usb_simtec_info;
+ int ret;
- s3c2410_gpio_cfgpin(S3C2410_GPB4, S3C2410_GPB4_OUTP);
- s3c2410_gpio_setpin(S3C2410_GPB4, 1);
+ printk("USB Power Control, (c) 2004 Simtec Electronics\n");
+
+ ret = gpio_request(S3C2410_GPB(4), "USB power control");
+ if (ret < 0) {
+ pr_err("%s: failed to get GPB4\n", __func__);
+ return ret;
+ }
+
+ ret = gpio_request(S3C2410_GPG(10), "USB overcurrent");
+ if (ret < 0) {
+ pr_err("%s: failed to get GPG10\n", __func__);
+ gpio_free(S3C2410_GPB(4));
+ return ret;
+ }
+
+ /* turn power on */
+ gpio_direction_output(S3C2410_GPB(4), 1);
+ gpio_direction_input(S3C2410_GPG(10));
+
+ s3c_device_usb.dev.platform_data = &usb_simtec_info;
return 0;
}
diff --git a/arch/arm/mach-s3c2412/Kconfig b/arch/arm/mach-s3c2412/Kconfig
index ca99564..63586ff 100644
--- a/arch/arm/mach-s3c2412/Kconfig
+++ b/arch/arm/mach-s3c2412/Kconfig
@@ -38,6 +38,7 @@
config MACH_JIVE
bool "Logitech Jive"
select CPU_S3C2412
+ select S3C_DEV_USB_HOST
help
Say Y here if you are using the Logitech Jive.
@@ -50,6 +51,7 @@
select CPU_S3C2412
select MACH_S3C2413
select MACH_SMDK
+ select S3C_DEV_USB_HOST
help
Say Y here if you are using an SMDK2413
@@ -72,6 +74,7 @@
config MACH_VSTMS
bool "VMSTMS"
select CPU_S3C2412
+ select S3C_DEV_USB_HOST
help
Say Y here if you are using an VSTMS board
diff --git a/arch/arm/mach-s3c2412/dma.c b/arch/arm/mach-s3c2412/dma.c
index 9e34785..f8d16fc 100644
--- a/arch/arm/mach-s3c2412/dma.c
+++ b/arch/arm/mach-s3c2412/dma.c
@@ -20,12 +20,13 @@
#include <mach/dma.h>
-#include <plat/dma.h>
+#include <plat/dma-plat.h>
#include <plat/cpu.h>
#include <plat/regs-serial.h>
#include <mach/regs-gpio.h>
#include <plat/regs-ac97.h>
+#include <plat/regs-dma.h>
#include <mach/regs-mem.h>
#include <mach/regs-lcd.h>
#include <mach/regs-sdi.h>
diff --git a/arch/arm/mach-s3c2412/mach-jive.c b/arch/arm/mach-s3c2412/mach-jive.c
index 8f0d37d..8df506e 100644
--- a/arch/arm/mach-s3c2412/mach-jive.c
+++ b/arch/arm/mach-s3c2412/mach-jive.c
@@ -16,6 +16,7 @@
#include <linux/list.h>
#include <linux/timer.h>
#include <linux/init.h>
+#include <linux/gpio.h>
#include <linux/sysdev.h>
#include <linux/serial_core.h>
#include <linux/platform_device.h>
@@ -356,8 +357,8 @@
{
printk(KERN_DEBUG "%s(%d)\n", __func__, set);
- s3c2410_gpio_setpin(S3C2410_GPG13, set);
- s3c2410_gpio_cfgpin(S3C2410_GPG13, S3C2410_GPIO_OUTPUT);
+ s3c2410_gpio_setpin(S3C2410_GPG(13), set);
+ s3c2410_gpio_cfgpin(S3C2410_GPG(13), S3C2410_GPIO_OUTPUT);
}
#undef LCD_UPPER_MARGIN
@@ -390,13 +391,13 @@
static void jive_lcd_spi_chipselect(struct s3c2410_spigpio_info *spi, int cs)
{
- s3c2410_gpio_setpin(S3C2410_GPB7, cs ? 0 : 1);
+ s3c2410_gpio_setpin(S3C2410_GPB(7), cs ? 0 : 1);
}
static struct s3c2410_spigpio_info jive_lcd_spi = {
.bus_num = 1,
- .pin_clk = S3C2410_GPG8,
- .pin_mosi = S3C2410_GPB8,
+ .pin_clk = S3C2410_GPG(8),
+ .pin_mosi = S3C2410_GPB(8),
.num_chipselect = 1,
.chip_select = jive_lcd_spi_chipselect,
};
@@ -412,13 +413,13 @@
static void jive_wm8750_chipselect(struct s3c2410_spigpio_info *spi, int cs)
{
- s3c2410_gpio_setpin(S3C2410_GPH10, cs ? 0 : 1);
+ s3c2410_gpio_setpin(S3C2410_GPH(10), cs ? 0 : 1);
}
static struct s3c2410_spigpio_info jive_wm8750_spi = {
.bus_num = 2,
- .pin_clk = S3C2410_GPB4,
- .pin_mosi = S3C2410_GPB9,
+ .pin_clk = S3C2410_GPB(4),
+ .pin_mosi = S3C2410_GPB(9),
.num_chipselect = 1,
.chip_select = jive_wm8750_chipselect,
};
@@ -479,7 +480,7 @@
};
static struct s3c2410_udc_mach_info jive_udc_cfg __initdata = {
- .vbus_pin = S3C2410_GPG1, /* detect is on GPG1 */
+ .vbus_pin = S3C2410_GPG(1), /* detect is on GPG1 */
};
/* Jive power management device */
@@ -529,8 +530,8 @@
{
printk(KERN_INFO "powering system down...\n");
- s3c2410_gpio_setpin(S3C2410_GPC5, 1);
- s3c2410_gpio_cfgpin(S3C2410_GPC5, S3C2410_GPIO_OUTPUT);
+ s3c2410_gpio_setpin(S3C2410_GPC(5), 1);
+ s3c2410_gpio_cfgpin(S3C2410_GPC(5), S3C2410_GPIO_OUTPUT);
}
static void __init jive_machine_init(void)
@@ -634,22 +635,22 @@
/* initialise the spi */
- s3c2410_gpio_setpin(S3C2410_GPG13, 0);
- s3c2410_gpio_cfgpin(S3C2410_GPG13, S3C2410_GPIO_OUTPUT);
+ s3c2410_gpio_setpin(S3C2410_GPG(13), 0);
+ s3c2410_gpio_cfgpin(S3C2410_GPG(13), S3C2410_GPIO_OUTPUT);
- s3c2410_gpio_setpin(S3C2410_GPB7, 1);
- s3c2410_gpio_cfgpin(S3C2410_GPB7, S3C2410_GPIO_OUTPUT);
+ s3c2410_gpio_setpin(S3C2410_GPB(7), 1);
+ s3c2410_gpio_cfgpin(S3C2410_GPB(7), S3C2410_GPIO_OUTPUT);
- s3c2410_gpio_setpin(S3C2410_GPB6, 0);
- s3c2410_gpio_cfgpin(S3C2410_GPB6, S3C2410_GPIO_OUTPUT);
+ s3c2410_gpio_setpin(S3C2410_GPB(6), 0);
+ s3c2410_gpio_cfgpin(S3C2410_GPB(6), S3C2410_GPIO_OUTPUT);
- s3c2410_gpio_setpin(S3C2410_GPG8, 1);
- s3c2410_gpio_cfgpin(S3C2410_GPG8, S3C2410_GPIO_OUTPUT);
+ s3c2410_gpio_setpin(S3C2410_GPG(8), 1);
+ s3c2410_gpio_cfgpin(S3C2410_GPG(8), S3C2410_GPIO_OUTPUT);
/* initialise the WM8750 spi */
- s3c2410_gpio_setpin(S3C2410_GPH10, 1);
- s3c2410_gpio_cfgpin(S3C2410_GPH10, S3C2410_GPIO_OUTPUT);
+ s3c2410_gpio_setpin(S3C2410_GPH(10), 1);
+ s3c2410_gpio_cfgpin(S3C2410_GPH(10), S3C2410_GPIO_OUTPUT);
/* Turn off suspend on both USB ports, and switch the
* selectable USB port to USB device mode. */
diff --git a/arch/arm/mach-s3c2412/mach-smdk2413.c b/arch/arm/mach-s3c2412/mach-smdk2413.c
index eba66aa..9a5e4341 100644
--- a/arch/arm/mach-s3c2412/mach-smdk2413.c
+++ b/arch/arm/mach-s3c2412/mach-smdk2413.c
@@ -17,6 +17,7 @@
#include <linux/list.h>
#include <linux/timer.h>
#include <linux/init.h>
+#include <linux/gpio.h>
#include <linux/serial_core.h>
#include <linux/platform_device.h>
#include <linux/io.h>
@@ -84,10 +85,10 @@
switch (cmd)
{
case S3C2410_UDC_P_ENABLE :
- s3c2410_gpio_setpin(S3C2410_GPF2, 1);
+ s3c2410_gpio_setpin(S3C2410_GPF(2), 1);
break;
case S3C2410_UDC_P_DISABLE :
- s3c2410_gpio_setpin(S3C2410_GPF2, 0);
+ s3c2410_gpio_setpin(S3C2410_GPF(2), 0);
break;
case S3C2410_UDC_P_RESET :
break;
@@ -134,8 +135,8 @@
{ /* Turn off suspend on both USB ports, and switch the
* selectable USB port to USB device mode. */
- s3c2410_gpio_setpin(S3C2410_GPF2, 0);
- s3c2410_gpio_cfgpin(S3C2410_GPF2, S3C2410_GPIO_OUTPUT);
+ s3c2410_gpio_setpin(S3C2410_GPF(2), 0);
+ s3c2410_gpio_cfgpin(S3C2410_GPF(2), S3C2410_GPIO_OUTPUT);
s3c2410_modify_misccr(S3C2410_MISCCR_USBHOST |
S3C2410_MISCCR_USBSUSPND0 |
diff --git a/arch/arm/mach-s3c2440/Kconfig b/arch/arm/mach-s3c2440/Kconfig
index cde5ae9..5df73cb 100644
--- a/arch/arm/mach-s3c2440/Kconfig
+++ b/arch/arm/mach-s3c2440/Kconfig
@@ -33,6 +33,7 @@
select PM_SIMTEC if PM
select HAVE_PATA_PLATFORM
select S3C24XX_GPIO_EXTRA64
+ select S3C_DEV_USB_HOST
help
Say Y here if you are using the Simtec Electronics ANUBIS
development system
@@ -43,6 +44,7 @@
select S3C24XX_DCLK
select PM_SIMTEC if PM
select S3C24XX_GPIO_EXTRA128
+ select S3C_DEV_USB_HOST
help
Say Y here if you are using the Simtec IM2440D20 module, also
known as the Osiris.
@@ -58,12 +60,14 @@
bool "SMDK2440"
select CPU_S3C2440
select MACH_SMDK
+ select S3C_DEV_USB_HOST
help
Say Y here if you are using the SMDK2440.
config MACH_NEXCODER_2440
bool "NexVision NEXCODER 2440 Light Board"
select CPU_S3C2440
+ select S3C_DEV_USB_HOST
help
Say Y here if you are using the Nex Vision NEXCODER 2440 Light Board
@@ -76,6 +80,7 @@
config MACH_AT2440EVB
bool "Avantech AT2440EVB development board"
select CPU_S3C2440
+ select S3C_DEV_USB_HOST
help
Say Y here if you are using the AT2440EVB development board
diff --git a/arch/arm/mach-s3c2440/dma.c b/arch/arm/mach-s3c2440/dma.c
index 69b6cf3..e08e081 100644
--- a/arch/arm/mach-s3c2440/dma.c
+++ b/arch/arm/mach-s3c2440/dma.c
@@ -17,14 +17,16 @@
#include <linux/sysdev.h>
#include <linux/serial_core.h>
+#include <mach/map.h>
#include <mach/dma.h>
-#include <plat/dma.h>
+#include <plat/dma-plat.h>
#include <plat/cpu.h>
#include <plat/regs-serial.h>
#include <mach/regs-gpio.h>
#include <plat/regs-ac97.h>
+#include <plat/regs-dma.h>
#include <mach/regs-mem.h>
#include <mach/regs-lcd.h>
#include <mach/regs-sdi.h>
diff --git a/arch/arm/mach-s3c2440/mach-anubis.c b/arch/arm/mach-s3c2440/mach-anubis.c
index 9c6abf9..68f3870 100644
--- a/arch/arm/mach-s3c2440/mach-anubis.c
+++ b/arch/arm/mach-s3c2440/mach-anubis.c
@@ -15,6 +15,7 @@
#include <linux/list.h>
#include <linux/timer.h>
#include <linux/init.h>
+#include <linux/gpio.h>
#include <linux/serial_core.h>
#include <linux/platform_device.h>
#include <linux/ata_platform.h>
@@ -468,7 +469,7 @@
anubis_nand_sets[0].nr_partitions = ARRAY_SIZE(anubis_default_nand_part_large);
} else {
/* ensure that the GPIO is setup */
- s3c2410_gpio_setpin(S3C2410_GPA0, 1);
+ s3c2410_gpio_setpin(S3C2410_GPA(0), 1);
}
}
diff --git a/arch/arm/mach-s3c2440/mach-at2440evb.c b/arch/arm/mach-s3c2440/mach-at2440evb.c
index 315c42e..dfc70109 100644
--- a/arch/arm/mach-s3c2440/mach-at2440evb.c
+++ b/arch/arm/mach-s3c2440/mach-at2440evb.c
@@ -166,7 +166,7 @@
};
static struct s3c24xx_mci_pdata at2440evb_mci_pdata = {
- .gpio_detect = S3C2410_GPG10,
+ .gpio_detect = S3C2410_GPG(10),
};
/* 7" LCD panel */
diff --git a/arch/arm/mach-s3c2440/mach-nexcoder.c b/arch/arm/mach-s3c2440/mach-nexcoder.c
index 7aeaa97..d43eded 100644
--- a/arch/arm/mach-s3c2440/mach-nexcoder.c
+++ b/arch/arm/mach-s3c2440/mach-nexcoder.c
@@ -18,6 +18,7 @@
#include <linux/list.h>
#include <linux/timer.h>
#include <linux/init.h>
+#include <linux/gpio.h>
#include <linux/string.h>
#include <linux/serial_core.h>
#include <linux/platform_device.h>
@@ -120,16 +121,16 @@
static void __init nexcoder_sensorboard_init(void)
{
// Initialize SCCB bus
- s3c2410_gpio_setpin(S3C2410_GPE14, 1); // IICSCL
- s3c2410_gpio_cfgpin(S3C2410_GPE14, S3C2410_GPE14_OUTP);
- s3c2410_gpio_setpin(S3C2410_GPE15, 1); // IICSDA
- s3c2410_gpio_cfgpin(S3C2410_GPE15, S3C2410_GPE15_OUTP);
+ s3c2410_gpio_setpin(S3C2410_GPE(14), 1); // IICSCL
+ s3c2410_gpio_cfgpin(S3C2410_GPE(14), S3C2410_GPIO_OUTPUT);
+ s3c2410_gpio_setpin(S3C2410_GPE(15), 1); // IICSDA
+ s3c2410_gpio_cfgpin(S3C2410_GPE(15), S3C2410_GPIO_OUTPUT);
// Power up the sensor board
- s3c2410_gpio_setpin(S3C2410_GPF1, 1);
- s3c2410_gpio_cfgpin(S3C2410_GPF1, S3C2410_GPF1_OUTP); // CAM_GPIO7 => nLDO_PWRDN
- s3c2410_gpio_setpin(S3C2410_GPF2, 0);
- s3c2410_gpio_cfgpin(S3C2410_GPF2, S3C2410_GPF2_OUTP); // CAM_GPIO6 => CAM_PWRDN
+ s3c2410_gpio_setpin(S3C2410_GPF(1), 1);
+ s3c2410_gpio_cfgpin(S3C2410_GPF(1), S3C2410_GPIO_OUTPUT); // CAM_GPIO7 => nLDO_PWRDN
+ s3c2410_gpio_setpin(S3C2410_GPF(2), 0);
+ s3c2410_gpio_cfgpin(S3C2410_GPF(2), S3C2410_GPIO_OUTPUT); // CAM_GPIO6 => CAM_PWRDN
}
static void __init nexcoder_map_io(void)
diff --git a/arch/arm/mach-s3c2440/mach-osiris.c b/arch/arm/mach-s3c2440/mach-osiris.c
index c8a4668..cba064b 100644
--- a/arch/arm/mach-s3c2440/mach-osiris.c
+++ b/arch/arm/mach-s3c2440/mach-osiris.c
@@ -15,6 +15,7 @@
#include <linux/list.h>
#include <linux/timer.h>
#include <linux/init.h>
+#include <linux/gpio.h>
#include <linux/device.h>
#include <linux/sysdev.h>
#include <linux/serial_core.h>
@@ -291,8 +292,8 @@
__raw_writeb(tmp, OSIRIS_VA_CTRL0);
/* ensure that an nRESET is not generated on resume. */
- s3c2410_gpio_setpin(S3C2410_GPA21, 1);
- s3c2410_gpio_cfgpin(S3C2410_GPA21, S3C2410_GPA21_OUT);
+ s3c2410_gpio_setpin(S3C2410_GPA(21), 1);
+ s3c2410_gpio_cfgpin(S3C2410_GPA(21), S3C2410_GPIO_OUTPUT);
return 0;
}
@@ -304,7 +305,7 @@
__raw_writeb(pm_osiris_ctrl0, OSIRIS_VA_CTRL0);
- s3c2410_gpio_cfgpin(S3C2410_GPA21, S3C2410_GPA21_nRSTOUT);
+ s3c2410_gpio_cfgpin(S3C2410_GPA(21), S3C2410_GPA21_nRSTOUT);
return 0;
}
@@ -384,7 +385,7 @@
osiris_nand_sets[0].nr_partitions = ARRAY_SIZE(osiris_default_nand_part_large);
} else {
/* write-protect line to the NAND */
- s3c2410_gpio_setpin(S3C2410_GPA0, 1);
+ s3c2410_gpio_setpin(S3C2410_GPA(0), 1);
}
/* fix bus configuration (nBE settings wrong on ABLE pre v2.20) */
diff --git a/arch/arm/mach-s3c2443/dma.c b/arch/arm/mach-s3c2443/dma.c
index 8430e582..397f3b5 100644
--- a/arch/arm/mach-s3c2443/dma.c
+++ b/arch/arm/mach-s3c2443/dma.c
@@ -20,12 +20,13 @@
#include <mach/dma.h>
-#include <plat/dma.h>
+#include <plat/dma-plat.h>
#include <plat/cpu.h>
#include <plat/regs-serial.h>
#include <mach/regs-gpio.h>
#include <plat/regs-ac97.h>
+#include <plat/regs-dma.h>
#include <mach/regs-mem.h>
#include <mach/regs-lcd.h>
#include <mach/regs-sdi.h>
diff --git a/arch/arm/mach-s3c6400/Kconfig b/arch/arm/mach-s3c6400/Kconfig
index 6da82b5..f5af212 100644
--- a/arch/arm/mach-s3c6400/Kconfig
+++ b/arch/arm/mach-s3c6400/Kconfig
@@ -5,4 +5,27 @@
#
# Licensed under GPLv2
-# Currently nothing here, this will be added later
+# Configuration options for the S3C6410 CPU
+
+config CPU_S3C6400
+ bool
+ select CPU_S3C6400_INIT
+ select CPU_S3C6400_CLOCK
+ help
+ Enable S3C6400 CPU support
+
+config S3C6400_SETUP_SDHCI
+ bool
+ help
+ Internal configuration for default SDHCI
+ setup for S3C6400.
+
+# S36400 Macchine support
+
+config MACH_SMDK6400
+ bool "SMDK6400"
+ select CPU_S3C6400
+ select S3C_DEV_HSMMC
+ select S3C6400_SETUP_SDHCI
+ help
+ Machine support for the Samsung SMDK6400
diff --git a/arch/arm/mach-s3c6400/Makefile b/arch/arm/mach-s3c6400/Makefile
index 8f397db..df1ce4a 100644
--- a/arch/arm/mach-s3c6400/Makefile
+++ b/arch/arm/mach-s3c6400/Makefile
@@ -12,4 +12,12 @@
# Core support for S3C6400 system
-obj-n += blank.o
+obj-$(CONFIG_CPU_S3C6400) += s3c6400.o
+
+# setup support
+
+obj-$(CONFIG_S3C6400_SETUP_SDHCI) += setup-sdhci.o
+
+# Machine support
+
+obj-$(CONFIG_MACH_SMDK6400) += mach-smdk6400.o
diff --git a/arch/arm/mach-s3c6400/include/mach/dma.h b/arch/arm/mach-s3c6400/include/mach/dma.h
index 9771ac2..1067619 100644
--- a/arch/arm/mach-s3c6400/include/mach/dma.h
+++ b/arch/arm/mach-s3c6400/include/mach/dma.h
@@ -11,6 +11,63 @@
#ifndef __ASM_ARCH_DMA_H
#define __ASM_ARCH_DMA_H __FILE__
-/* currently nothing here, placeholder */
+#define S3C_DMA_CHANNELS (16)
+
+/* see mach-s3c2410/dma.h for notes on dma channel numbers */
+
+/* Note, for the S3C64XX architecture we keep the DMACH_
+ * defines in the order they are allocated to [S]DMA0/[S]DMA1
+ * so that is easy to do DHACH_ -> DMA controller conversion
+ */
+enum dma_ch {
+ /* DMA0/SDMA0 */
+ DMACH_UART0 = 0,
+ DMACH_UART0_SRC2,
+ DMACH_UART1,
+ DMACH_UART1_SRC2,
+ DMACH_UART2,
+ DMACH_UART2_SRC2,
+ DMACH_UART3,
+ DMACH_UART3_SRC2,
+ DMACH_PCM0_TX,
+ DMACH_PCM0_RX,
+ DMACH_I2S0_OUT,
+ DMACH_I2S0_IN,
+ DMACH_SPI0_TX,
+ DMACH_SPI0_RX,
+ DMACH_HSI_I2SV40_TX,
+ DMACH_HSI_I2SV40_RX,
+
+ /* DMA1/SDMA1 */
+ DMACH_PCM1_TX = 16,
+ DMACH_PCM1_RX,
+ DMACH_I2S1_OUT,
+ DMACH_I2S1_IN,
+ DMACH_SPI1_TX,
+ DMACH_SPI1_RX,
+ DMACH_AC97_PCMOUT,
+ DMACH_AC97_PCMIN,
+ DMACH_AC97_MICIN,
+ DMACH_PWM,
+ DMACH_IRDA,
+ DMACH_EXTERNAL,
+ DMACH_RES1,
+ DMACH_RES2,
+ DMACH_SECURITY_RX, /* SDMA1 only */
+ DMACH_SECURITY_TX, /* SDMA1 only */
+ DMACH_MAX /* the end */
+};
+
+static __inline__ int s3c_dma_has_circular(void)
+{
+ /* we will be supporting ciruclar buffers as soon as we have DMA
+ * engine support.
+ */
+ return 1;
+}
+
+#define S3C2410_DMAF_CIRCULAR (1 << 0)
+
+#include <plat/dma.h>
#endif /* __ASM_ARCH_IRQ_H */
diff --git a/arch/arm/mach-s3c6400/include/mach/map.h b/arch/arm/mach-s3c6400/include/mach/map.h
index 8199972..5057d99 100644
--- a/arch/arm/mach-s3c6400/include/mach/map.h
+++ b/arch/arm/mach-s3c6400/include/mach/map.h
@@ -39,6 +39,8 @@
#define S3C_VA_UART3 S3C_VA_UARTx(3)
#define S3C64XX_PA_FB (0x77100000)
+#define S3C64XX_PA_USB_HSOTG (0x7C000000)
+#define S3C64XX_PA_WATCHDOG (0x7E004000)
#define S3C64XX_PA_SYSCON (0x7E00F000)
#define S3C64XX_PA_IIS0 (0x7F002000)
#define S3C64XX_PA_IIS1 (0x7F003000)
@@ -57,6 +59,8 @@
#define S3C64XX_PA_MODEM (0x74108000)
#define S3C64XX_VA_MODEM S3C_ADDR(0x00600000)
+#define S3C64XX_PA_USBHOST (0x74300000)
+
/* place VICs close together */
#define S3C_VA_VIC0 (S3C_VA_IRQ + 0x00)
#define S3C_VA_VIC1 (S3C_VA_IRQ + 0x10000)
@@ -69,5 +73,7 @@
#define S3C_PA_IIC S3C64XX_PA_IIC0
#define S3C_PA_IIC1 S3C64XX_PA_IIC1
#define S3C_PA_FB S3C64XX_PA_FB
+#define S3C_PA_USBHOST S3C64XX_PA_USBHOST
+#define S3C_PA_USB_HSOTG S3C64XX_PA_USB_HSOTG
#endif /* __ASM_ARCH_6400_MAP_H */
diff --git a/arch/arm/mach-s3c6400/include/mach/regs-clock.h b/arch/arm/mach-s3c6400/include/mach/regs-clock.h
new file mode 100644
index 0000000..a6c7f4e
--- /dev/null
+++ b/arch/arm/mach-s3c6400/include/mach/regs-clock.h
@@ -0,0 +1,16 @@
+/* linux/arch/arm/mach-s3c6400/include/mach/regs-clock.h
+ *
+ * Copyright 2008 Openmoko, Inc.
+ * Copyright 2008 Simtec Electronics
+ * http://armlinux.simtec.co.uk/
+ * Ben Dooks <ben@simtec.co.uk>
+ *
+ * S3C64XX - clock register compatibility with s3c24xx
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <plat/regs-clock.h>
+
diff --git a/arch/arm/mach-s3c6400/include/mach/system.h b/arch/arm/mach-s3c6400/include/mach/system.h
index 090cfd9..2e58cb7 100644
--- a/arch/arm/mach-s3c6400/include/mach/system.h
+++ b/arch/arm/mach-s3c6400/include/mach/system.h
@@ -11,6 +11,8 @@
#ifndef __ASM_ARCH_SYSTEM_H
#define __ASM_ARCH_SYSTEM_H __FILE__
+#include <plat/watchdog-reset.h>
+
static void arch_idle(void)
{
/* nothing here yet */
@@ -18,7 +20,11 @@
static void arch_reset(char mode, const char *cmd)
{
- /* nothing here yet */
+ if (mode != 's')
+ arch_wdt_reset();
+
+ /* if all else fails, or mode was for soft, jump to 0 */
+ cpu_reset(0);
}
#endif /* __ASM_ARCH_IRQ_H */
diff --git a/arch/arm/mach-s3c6400/mach-smdk6400.c b/arch/arm/mach-s3c6400/mach-smdk6400.c
new file mode 100644
index 0000000..ab19285
--- /dev/null
+++ b/arch/arm/mach-s3c6400/mach-smdk6400.c
@@ -0,0 +1,96 @@
+/* linux/arch/arm/mach-s3c6400/mach-smdk6400.c
+ *
+ * Copyright 2008 Simtec Electronics
+ * Ben Dooks <ben@simtec.co.uk>
+ * http://armlinux.simtec.co.uk/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/interrupt.h>
+#include <linux/list.h>
+#include <linux/timer.h>
+#include <linux/init.h>
+#include <linux/serial_core.h>
+#include <linux/platform_device.h>
+#include <linux/i2c.h>
+#include <linux/io.h>
+
+#include <asm/mach-types.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include <mach/hardware.h>
+#include <mach/map.h>
+
+#include <plat/regs-serial.h>
+
+#include <plat/s3c6400.h>
+#include <plat/clock.h>
+#include <plat/devs.h>
+#include <plat/cpu.h>
+#include <plat/iic.h>
+
+#define UCON S3C2410_UCON_DEFAULT | S3C2410_UCON_UCLK
+#define ULCON S3C2410_LCON_CS8 | S3C2410_LCON_PNONE | S3C2410_LCON_STOPB
+#define UFCON S3C2410_UFCON_RXTRIG8 | S3C2410_UFCON_FIFOMODE
+
+static struct s3c2410_uartcfg smdk6400_uartcfgs[] __initdata = {
+ [0] = {
+ .hwport = 0,
+ .flags = 0,
+ .ucon = 0x3c5,
+ .ulcon = 0x03,
+ .ufcon = 0x51,
+ },
+ [1] = {
+ .hwport = 1,
+ .flags = 0,
+ .ucon = 0x3c5,
+ .ulcon = 0x03,
+ .ufcon = 0x51,
+ },
+};
+
+static struct map_desc smdk6400_iodesc[] = {};
+
+static void __init smdk6400_map_io(void)
+{
+ s3c64xx_init_io(smdk6400_iodesc, ARRAY_SIZE(smdk6400_iodesc));
+ s3c24xx_init_clocks(12000000);
+ s3c24xx_init_uarts(smdk6400_uartcfgs, ARRAY_SIZE(smdk6400_uartcfgs));
+}
+
+static struct platform_device *smdk6400_devices[] __initdata = {
+ &s3c_device_hsmmc1,
+ &s3c_device_i2c0,
+};
+
+static struct i2c_board_info i2c_devs[] __initdata = {
+ { I2C_BOARD_INFO("wm8753", 0x1A), },
+ { I2C_BOARD_INFO("24c08", 0x50), },
+};
+
+static void __init smdk6400_machine_init(void)
+{
+ i2c_register_board_info(0, i2c_devs, ARRAY_SIZE(i2c_devs));
+ platform_add_devices(smdk6400_devices, ARRAY_SIZE(smdk6400_devices));
+}
+
+MACHINE_START(SMDK6400, "SMDK6400")
+ /* Maintainer: Ben Dooks <ben@fluff.org> */
+ .phys_io = S3C_PA_UART & 0xfff00000,
+ .io_pg_offst = (((u32)S3C_VA_UART) >> 18) & 0xfffc,
+ .boot_params = S3C64XX_PA_SDRAM + 0x100,
+
+ .init_irq = s3c6400_init_irq,
+ .map_io = smdk6400_map_io,
+ .init_machine = smdk6400_machine_init,
+ .timer = &s3c24xx_timer,
+MACHINE_END
diff --git a/arch/arm/mach-s3c6400/s3c6400.c b/arch/arm/mach-s3c6400/s3c6400.c
new file mode 100644
index 0000000..1ece887
--- /dev/null
+++ b/arch/arm/mach-s3c6400/s3c6400.c
@@ -0,0 +1,89 @@
+/* linux/arch/arm/mach-s3c6410/cpu.c
+ *
+ * Copyright 2009 Simtec Electronics
+ * Ben Dooks <ben@simtec.co.uk>
+ * http://armlinux.simtec.co.uk/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/interrupt.h>
+#include <linux/list.h>
+#include <linux/timer.h>
+#include <linux/init.h>
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/sysdev.h>
+#include <linux/serial_core.h>
+#include <linux/platform_device.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include <mach/hardware.h>
+#include <asm/irq.h>
+
+#include <plat/cpu-freq.h>
+#include <plat/regs-serial.h>
+#include <plat/regs-clock.h>
+
+#include <plat/cpu.h>
+#include <plat/devs.h>
+#include <plat/clock.h>
+#include <plat/sdhci.h>
+#include <plat/iic-core.h>
+#include <plat/s3c6400.h>
+
+void __init s3c6400_map_io(void)
+{
+ /* setup SDHCI */
+
+ s3c6400_default_sdhci0();
+ s3c6400_default_sdhci1();
+
+ /* the i2c devices are directly compatible with s3c2440 */
+ s3c_i2c0_setname("s3c2440-i2c");
+}
+
+void __init s3c6400_init_clocks(int xtal)
+{
+ printk(KERN_DEBUG "%s: initialising clocks\n", __func__);
+ s3c24xx_register_baseclocks(xtal);
+ s3c64xx_register_clocks();
+ s3c6400_register_clocks(S3C6400_CLKDIV0_ARM_MASK);
+ s3c6400_setup_clocks();
+}
+
+void __init s3c6400_init_irq(void)
+{
+ /* VIC0 does not have IRQS 5..7,
+ * VIC1 is fully populated. */
+ s3c64xx_init_irq(~0 & ~(0xf << 5), ~0);
+}
+
+struct sysdev_class s3c6400_sysclass = {
+ .name = "s3c6400-core",
+};
+
+static struct sys_device s3c6400_sysdev = {
+ .cls = &s3c6400_sysclass,
+};
+
+static int __init s3c6400_core_init(void)
+{
+ return sysdev_class_register(&s3c6400_sysclass);
+}
+
+core_initcall(s3c6400_core_init);
+
+int __init s3c6400_init(void)
+{
+ printk("S3C6400: Initialising architecture\n");
+
+ return sysdev_register(&s3c6400_sysdev);
+}
diff --git a/arch/arm/mach-s3c6400/setup-sdhci.c b/arch/arm/mach-s3c6400/setup-sdhci.c
new file mode 100644
index 0000000..b93dafb
--- /dev/null
+++ b/arch/arm/mach-s3c6400/setup-sdhci.c
@@ -0,0 +1,63 @@
+/* linux/arch/arm/mach-s3c6410/setup-sdhci.c
+ *
+ * Copyright 2008 Simtec Electronics
+ * Copyright 2008 Simtec Electronics
+ * Ben Dooks <ben@simtec.co.uk>
+ * http://armlinux.simtec.co.uk/
+ *
+ * S3C6410 - Helper functions for settign up SDHCI device(s) (HSMMC)
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+
+#include <linux/mmc/card.h>
+#include <linux/mmc/host.h>
+
+#include <plat/regs-sdhci.h>
+#include <plat/sdhci.h>
+
+/* clock sources for the mmc bus clock, order as for the ctrl2[5..4] */
+
+char *s3c6400_hsmmc_clksrcs[4] = {
+ [0] = "hsmmc",
+ [1] = "hsmmc",
+ [2] = "mmc_bus",
+ /* [3] = "48m", - note not succesfully used yet */
+};
+
+void s3c6400_setup_sdhci_cfg_card(struct platform_device *dev,
+ void __iomem *r,
+ struct mmc_ios *ios,
+ struct mmc_card *card)
+{
+ u32 ctrl2, ctrl3;
+
+ ctrl2 = readl(r + S3C_SDHCI_CONTROL2);
+ ctrl2 &= S3C_SDHCI_CTRL2_SELBASECLK_MASK;
+ ctrl2 |= (S3C64XX_SDHCI_CTRL2_ENSTAASYNCCLR |
+ S3C64XX_SDHCI_CTRL2_ENCMDCNFMSK |
+ S3C_SDHCI_CTRL2_ENFBCLKRX |
+ S3C_SDHCI_CTRL2_DFCNT_NONE |
+ S3C_SDHCI_CTRL2_ENCLKOUTHOLD);
+
+ if (ios->clock < 25 * 1000000)
+ ctrl3 = (S3C_SDHCI_CTRL3_FCSEL3 |
+ S3C_SDHCI_CTRL3_FCSEL2 |
+ S3C_SDHCI_CTRL3_FCSEL1 |
+ S3C_SDHCI_CTRL3_FCSEL0);
+ else
+ ctrl3 = (S3C_SDHCI_CTRL3_FCSEL1 | S3C_SDHCI_CTRL3_FCSEL0);
+
+ printk(KERN_INFO "%s: CTRL 2=%08x, 3=%08x\n", __func__, ctrl2, ctrl3);
+ writel(ctrl2, r + S3C_SDHCI_CONTROL2);
+ writel(ctrl3, r + S3C_SDHCI_CONTROL3);
+}
+
diff --git a/arch/arm/mach-s3c6410/Kconfig b/arch/arm/mach-s3c6410/Kconfig
index 1d50100..e63aac7f 100644
--- a/arch/arm/mach-s3c6410/Kconfig
+++ b/arch/arm/mach-s3c6410/Kconfig
@@ -16,9 +16,18 @@
config S3C6410_SETUP_SDHCI
bool
+ select S3C64XX_SETUP_SDHCI_GPIO
help
Internal helper functions for S3C6410 based SDHCI systems
+config MACH_ANW6410
+ bool "A&W6410"
+ select CPU_S3C6410
+ select S3C_DEV_FB
+ select S3C64XX_SETUP_FB_24BPP
+ help
+ Machine support for the A&W6410
+
config MACH_SMDK6410
bool "SMDK6410"
select CPU_S3C6410
@@ -26,6 +35,8 @@
select S3C_DEV_HSMMC1
select S3C_DEV_I2C1
select S3C_DEV_FB
+ select S3C_DEV_USB_HOST
+ select S3C_DEV_USB_HSOTG
select S3C6410_SETUP_SDHCI
select S3C64XX_SETUP_I2C1
select S3C64XX_SETUP_FB_24BPP
@@ -60,3 +71,29 @@
channels 0 and 1 are the same.
endchoice
+
+config SMDK6410_WM1190_EV1
+ bool "Support Wolfson Microelectronics 1190-EV1 PMIC card"
+ depends on MACH_SMDK6410
+ select REGULATOR
+ select REGULATOR_WM8350
+ select MFD_WM8350_I2C
+ select MFD_WM8350_CONFIG_MODE_0
+ select MFD_WM8350_CONFIG_MODE_3
+ select MFD_WM8352_CONFIG_MODE_0
+ help
+ The Wolfson Microelectronics 1190-EV1 is a WM835x based PMIC
+ and audio daughtercard for the Samsung SMDK6410 reference
+ platform. Enabling this option will build support for this
+ module into the kernel. The presence of the module will be
+ detected at runtime so the the resulting kernel can be used
+ with or without the 1190-EV1 fitted.
+
+config MACH_NCP
+ bool "NCP"
+ select CPU_S3C6410
+ select S3C_DEV_I2C1
+ select S3C_DEV_HSMMC1
+ select S3C64XX_SETUP_I2C1
+ help
+ Machine support for the Samsung NCP
diff --git a/arch/arm/mach-s3c6410/Makefile b/arch/arm/mach-s3c6410/Makefile
index 2cd4f18..6f9deac 100644
--- a/arch/arm/mach-s3c6410/Makefile
+++ b/arch/arm/mach-s3c6410/Makefile
@@ -20,4 +20,8 @@
# machine support
+obj-$(CONFIG_MACH_ANW6410) += mach-anw6410.o
obj-$(CONFIG_MACH_SMDK6410) += mach-smdk6410.o
+obj-$(CONFIG_MACH_NCP) += mach-ncp.o
+
+
diff --git a/arch/arm/mach-s3c6410/cpu.c b/arch/arm/mach-s3c6410/cpu.c
index 6a73ca6..ade904d 100644
--- a/arch/arm/mach-s3c6410/cpu.c
+++ b/arch/arm/mach-s3c6410/cpu.c
@@ -31,6 +31,7 @@
#include <plat/cpu-freq.h>
#include <plat/regs-serial.h>
+#include <plat/regs-clock.h>
#include <plat/cpu.h>
#include <plat/devs.h>
@@ -68,7 +69,7 @@
printk(KERN_DEBUG "%s: initialising clocks\n", __func__);
s3c24xx_register_baseclocks(xtal);
s3c64xx_register_clocks();
- s3c6400_register_clocks();
+ s3c6400_register_clocks(S3C6410_CLKDIV0_ARM_MASK);
s3c6400_setup_clocks();
}
diff --git a/arch/arm/mach-s3c6410/mach-anw6410.c b/arch/arm/mach-s3c6410/mach-anw6410.c
new file mode 100644
index 0000000..661cca6
--- /dev/null
+++ b/arch/arm/mach-s3c6410/mach-anw6410.c
@@ -0,0 +1,245 @@
+/* linux/arch/arm/mach-s3c6410/mach-anw6410.c
+ *
+ * Copyright 2008 Openmoko, Inc.
+ * Copyright 2008 Simtec Electronics
+ * Ben Dooks <ben@simtec.co.uk>
+ * http://armlinux.simtec.co.uk/
+ * Copyright 2009 Kwangwoo Lee
+ * Kwangwoo Lee <kwangwoo.lee@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+*/
+
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/interrupt.h>
+#include <linux/list.h>
+#include <linux/timer.h>
+#include <linux/init.h>
+#include <linux/serial_core.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/i2c.h>
+#include <linux/fb.h>
+#include <linux/gpio.h>
+#include <linux/delay.h>
+#include <linux/dm9000.h>
+
+#include <video/platform_lcd.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include <mach/hardware.h>
+#include <mach/regs-fb.h>
+#include <mach/map.h>
+
+#include <asm/irq.h>
+#include <asm/mach-types.h>
+
+#include <plat/regs-serial.h>
+#include <plat/iic.h>
+#include <plat/fb.h>
+
+#include <plat/s3c6410.h>
+#include <plat/clock.h>
+#include <plat/devs.h>
+#include <plat/cpu.h>
+#include <plat/regs-gpio.h>
+#include <plat/regs-modem.h>
+
+/* DM9000 */
+#define ANW6410_PA_DM9000 (0x18000000)
+
+/* A hardware buffer to control external devices is mapped at 0x30000000.
+ * It can not be read. So current status must be kept in anw6410_extdev_status.
+ */
+#define ANW6410_VA_EXTDEV S3C_ADDR(0x02000000)
+#define ANW6410_PA_EXTDEV (0x30000000)
+
+#define ANW6410_EN_DM9000 (1<<11)
+#define ANW6410_EN_LCD (1<<14)
+
+static __u32 anw6410_extdev_status;
+
+static struct s3c2410_uartcfg anw6410_uartcfgs[] __initdata = {
+ [0] = {
+ .hwport = 0,
+ .flags = 0,
+ .ucon = 0x3c5,
+ .ulcon = 0x03,
+ .ufcon = 0x51,
+ },
+ [1] = {
+ .hwport = 1,
+ .flags = 0,
+ .ucon = 0x3c5,
+ .ulcon = 0x03,
+ .ufcon = 0x51,
+ },
+};
+
+/* framebuffer and LCD setup. */
+static void __init anw6410_lcd_mode_set(void)
+{
+ u32 tmp;
+
+ /* set the LCD type */
+ tmp = __raw_readl(S3C64XX_SPCON);
+ tmp &= ~S3C64XX_SPCON_LCD_SEL_MASK;
+ tmp |= S3C64XX_SPCON_LCD_SEL_RGB;
+ __raw_writel(tmp, S3C64XX_SPCON);
+
+ /* remove the LCD bypass */
+ tmp = __raw_readl(S3C64XX_MODEM_MIFPCON);
+ tmp &= ~MIFPCON_LCD_BYPASS;
+ __raw_writel(tmp, S3C64XX_MODEM_MIFPCON);
+}
+
+/* GPF1 = LCD panel power
+ * GPF4 = LCD backlight control
+ */
+static void anw6410_lcd_power_set(struct plat_lcd_data *pd,
+ unsigned int power)
+{
+ if (power) {
+ anw6410_extdev_status |= (ANW6410_EN_LCD << 16);
+ __raw_writel(anw6410_extdev_status, ANW6410_VA_EXTDEV);
+
+ gpio_direction_output(S3C64XX_GPF(1), 1);
+ gpio_direction_output(S3C64XX_GPF(4), 1);
+ } else {
+ anw6410_extdev_status &= ~(ANW6410_EN_LCD << 16);
+ __raw_writel(anw6410_extdev_status, ANW6410_VA_EXTDEV);
+
+ gpio_direction_output(S3C64XX_GPF(1), 0);
+ gpio_direction_output(S3C64XX_GPF(4), 0);
+ }
+}
+
+static struct plat_lcd_data anw6410_lcd_power_data = {
+ .set_power = anw6410_lcd_power_set,
+};
+
+static struct platform_device anw6410_lcd_powerdev = {
+ .name = "platform-lcd",
+ .dev.parent = &s3c_device_fb.dev,
+ .dev.platform_data = &anw6410_lcd_power_data,
+};
+
+static struct s3c_fb_pd_win anw6410_fb_win0 = {
+ /* this is to ensure we use win0 */
+ .win_mode = {
+ .pixclock = 41094,
+ .left_margin = 8,
+ .right_margin = 13,
+ .upper_margin = 7,
+ .lower_margin = 5,
+ .hsync_len = 3,
+ .vsync_len = 1,
+ .xres = 800,
+ .yres = 480,
+ },
+ .max_bpp = 32,
+ .default_bpp = 16,
+};
+
+/* 405566 clocks per frame => 60Hz refresh requires 24333960Hz clock */
+static struct s3c_fb_platdata anw6410_lcd_pdata __initdata = {
+ .setup_gpio = s3c64xx_fb_gpio_setup_24bpp,
+ .win[0] = &anw6410_fb_win0,
+ .vidcon0 = VIDCON0_VIDOUT_RGB | VIDCON0_PNRMODE_RGB,
+ .vidcon1 = VIDCON1_INV_HSYNC | VIDCON1_INV_VSYNC,
+};
+
+/* DM9000AEP 10/100 ethernet controller */
+static void __init anw6410_dm9000_enable(void)
+{
+ anw6410_extdev_status |= (ANW6410_EN_DM9000 << 16);
+ __raw_writel(anw6410_extdev_status, ANW6410_VA_EXTDEV);
+}
+
+static struct resource anw6410_dm9000_resource[] = {
+ [0] = {
+ .start = ANW6410_PA_DM9000,
+ .end = ANW6410_PA_DM9000 + 3,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = ANW6410_PA_DM9000 + 4,
+ .end = ANW6410_PA_DM9000 + 4 + 500,
+ .flags = IORESOURCE_MEM,
+ },
+ [2] = {
+ .start = IRQ_EINT(15),
+ .end = IRQ_EINT(15),
+ .flags = IORESOURCE_IRQ | IRQF_TRIGGER_HIGH,
+ },
+};
+
+static struct dm9000_plat_data anw6410_dm9000_pdata = {
+ .flags = (DM9000_PLATF_16BITONLY | DM9000_PLATF_NO_EEPROM),
+ /* dev_addr can be set to provide hwaddr. */
+};
+
+static struct platform_device anw6410_device_eth = {
+ .name = "dm9000",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(anw6410_dm9000_resource),
+ .resource = anw6410_dm9000_resource,
+ .dev = {
+ .platform_data = &anw6410_dm9000_pdata,
+ },
+};
+
+static struct map_desc anw6410_iodesc[] __initdata = {
+ {
+ .virtual = (unsigned long)ANW6410_VA_EXTDEV,
+ .pfn = __phys_to_pfn(ANW6410_PA_EXTDEV),
+ .length = SZ_64K,
+ .type = MT_DEVICE,
+ },
+};
+
+static struct platform_device *anw6410_devices[] __initdata = {
+ &s3c_device_fb,
+ &anw6410_lcd_powerdev,
+ &anw6410_device_eth,
+};
+
+static void __init anw6410_map_io(void)
+{
+ s3c64xx_init_io(anw6410_iodesc, ARRAY_SIZE(anw6410_iodesc));
+ s3c24xx_init_clocks(12000000);
+ s3c24xx_init_uarts(anw6410_uartcfgs, ARRAY_SIZE(anw6410_uartcfgs));
+
+ anw6410_lcd_mode_set();
+}
+
+static void __init anw6410_machine_init(void)
+{
+ s3c_fb_set_platdata(&anw6410_lcd_pdata);
+
+ gpio_request(S3C64XX_GPF(1), "panel power");
+ gpio_request(S3C64XX_GPF(4), "LCD backlight");
+
+ anw6410_dm9000_enable();
+
+ platform_add_devices(anw6410_devices, ARRAY_SIZE(anw6410_devices));
+}
+
+MACHINE_START(ANW6410, "A&W6410")
+ /* Maintainer: Kwangwoo Lee <kwangwoo.lee@gmail.com> */
+ .phys_io = S3C_PA_UART & 0xfff00000,
+ .io_pg_offst = (((u32)S3C_VA_UART) >> 18) & 0xfffc,
+ .boot_params = S3C64XX_PA_SDRAM + 0x100,
+
+ .init_irq = s3c6410_init_irq,
+ .map_io = anw6410_map_io,
+ .init_machine = anw6410_machine_init,
+ .timer = &s3c24xx_timer,
+MACHINE_END
diff --git a/arch/arm/mach-s3c6410/mach-ncp.c b/arch/arm/mach-s3c6410/mach-ncp.c
new file mode 100644
index 0000000..6030636
--- /dev/null
+++ b/arch/arm/mach-s3c6410/mach-ncp.c
@@ -0,0 +1,107 @@
+/*
+ * linux/arch/arm/mach-s3c6410/mach-ncp.c
+ *
+ * Copyright (C) 2008-2009 Samsung Electronics
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/interrupt.h>
+#include <linux/list.h>
+#include <linux/timer.h>
+#include <linux/init.h>
+#include <linux/serial_core.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/i2c.h>
+#include <linux/fb.h>
+#include <linux/gpio.h>
+#include <linux/delay.h>
+
+#include <video/platform_lcd.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include <mach/hardware.h>
+#include <mach/regs-fb.h>
+#include <mach/map.h>
+
+#include <asm/irq.h>
+#include <asm/mach-types.h>
+
+#include <plat/regs-serial.h>
+#include <plat/iic.h>
+#include <plat/fb.h>
+
+#include <plat/s3c6410.h>
+#include <plat/clock.h>
+#include <plat/devs.h>
+#include <plat/cpu.h>
+
+#define UCON S3C2410_UCON_DEFAULT
+#define ULCON S3C2410_LCON_CS8 | S3C2410_LCON_PNONE
+#define UFCON S3C2410_UFCON_RXTRIG8 | S3C2410_UFCON_FIFOMODE
+
+static struct s3c2410_uartcfg ncp_uartcfgs[] __initdata = {
+ /* REVISIT: NCP uses only serial 1, 2 */
+ [0] = {
+ .hwport = 0,
+ .flags = 0,
+ .ucon = UCON,
+ .ulcon = ULCON,
+ .ufcon = UFCON,
+ },
+ [1] = {
+ .hwport = 1,
+ .flags = 0,
+ .ucon = UCON,
+ .ulcon = ULCON,
+ .ufcon = UFCON,
+ },
+ [2] = {
+ .hwport = 2,
+ .flags = 0,
+ .ucon = UCON,
+ .ulcon = ULCON,
+ .ufcon = UFCON,
+ },
+};
+
+static struct platform_device *ncp_devices[] __initdata = {
+ &s3c_device_hsmmc1,
+ &s3c_device_i2c0,
+};
+
+struct map_desc ncp_iodesc[] = {};
+
+static void __init ncp_map_io(void)
+{
+ s3c64xx_init_io(ncp_iodesc, ARRAY_SIZE(ncp_iodesc));
+ s3c24xx_init_clocks(12000000);
+ s3c24xx_init_uarts(ncp_uartcfgs, ARRAY_SIZE(ncp_uartcfgs));
+}
+
+static void __init ncp_machine_init(void)
+{
+ s3c_i2c0_set_platdata(NULL);
+
+ platform_add_devices(ncp_devices, ARRAY_SIZE(ncp_devices));
+}
+
+MACHINE_START(NCP, "NCP")
+ /* Maintainer: Samsung Electronics */
+ .phys_io = S3C_PA_UART & 0xfff00000,
+ .io_pg_offst = (((u32)S3C_VA_UART) >> 18) & 0xfffc,
+ .boot_params = S3C64XX_PA_SDRAM + 0x100,
+ .init_irq = s3c6410_init_irq,
+ .map_io = ncp_map_io,
+ .init_machine = ncp_machine_init,
+ .timer = &s3c24xx_timer,
+MACHINE_END
diff --git a/arch/arm/mach-s3c6410/mach-smdk6410.c b/arch/arm/mach-s3c6410/mach-smdk6410.c
index 7f473e4..bc9a7de 100644
--- a/arch/arm/mach-s3c6410/mach-smdk6410.c
+++ b/arch/arm/mach-s3c6410/mach-smdk6410.c
@@ -24,6 +24,12 @@
#include <linux/fb.h>
#include <linux/gpio.h>
#include <linux/delay.h>
+#include <linux/smsc911x.h>
+
+#ifdef CONFIG_SMDK6410_WM1190_EV1
+#include <linux/mfd/wm8350/core.h>
+#include <linux/mfd/wm8350/pmic.h>
+#endif
#include <video/platform_lcd.h>
@@ -39,8 +45,12 @@
#include <asm/mach-types.h>
#include <plat/regs-serial.h>
+#include <plat/regs-modem.h>
+#include <plat/regs-gpio.h>
+#include <plat/regs-sys.h>
#include <plat/iic.h>
#include <plat/fb.h>
+#include <plat/gpio-cfg.h>
#include <plat/s3c6410.h>
#include <plat/clock.h>
@@ -129,6 +139,37 @@
.vidcon1 = VIDCON1_INV_HSYNC | VIDCON1_INV_VSYNC,
};
+static struct resource smdk6410_smsc911x_resources[] = {
+ [0] = {
+ .start = 0x18000000,
+ .end = 0x18000000 + SZ_64K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = S3C_EINT(10),
+ .end = S3C_EINT(10),
+ .flags = IORESOURCE_IRQ | IRQ_TYPE_LEVEL_LOW,
+ },
+};
+
+static struct smsc911x_platform_config smdk6410_smsc911x_pdata = {
+ .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
+ .irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN,
+ .flags = SMSC911X_USE_32BIT | SMSC911X_FORCE_INTERNAL_PHY,
+ .phy_interface = PHY_INTERFACE_MODE_MII,
+};
+
+
+static struct platform_device smdk6410_smsc911x = {
+ .name = "smsc911x",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(smdk6410_smsc911x_resources),
+ .resource = &smdk6410_smsc911x_resources[0],
+ .dev = {
+ .platform_data = &smdk6410_smsc911x_pdata,
+ },
+};
+
static struct map_desc smdk6410_iodesc[] = {};
static struct platform_device *smdk6410_devices[] __initdata = {
@@ -141,12 +182,155 @@
&s3c_device_i2c0,
&s3c_device_i2c1,
&s3c_device_fb,
+ &s3c_device_usb,
+ &s3c_device_usb_hsotg,
&smdk6410_lcd_powerdev,
+
+ &smdk6410_smsc911x,
};
+#ifdef CONFIG_SMDK6410_WM1190_EV1
+/* S3C64xx internal logic & PLL */
+static struct regulator_init_data wm8350_dcdc1_data = {
+ .constraints = {
+ .name = "PVDD_INT/PVDD_PLL",
+ .min_uV = 1200000,
+ .max_uV = 1200000,
+ .always_on = 1,
+ .apply_uV = 1,
+ },
+};
+
+/* Memory */
+static struct regulator_init_data wm8350_dcdc3_data = {
+ .constraints = {
+ .name = "PVDD_MEM",
+ .min_uV = 1800000,
+ .max_uV = 1800000,
+ .always_on = 1,
+ .state_mem = {
+ .uV = 1800000,
+ .mode = REGULATOR_MODE_NORMAL,
+ .enabled = 1,
+ },
+ .initial_state = PM_SUSPEND_MEM,
+ },
+};
+
+/* USB, EXT, PCM, ADC/DAC, USB, MMC */
+static struct regulator_init_data wm8350_dcdc4_data = {
+ .constraints = {
+ .name = "PVDD_HI/PVDD_EXT/PVDD_SYS/PVCCM2MTV",
+ .min_uV = 3000000,
+ .max_uV = 3000000,
+ .always_on = 1,
+ },
+};
+
+/* ARM core */
+static struct regulator_consumer_supply dcdc6_consumers[] = {
+ {
+ .supply = "vddarm",
+ }
+};
+
+static struct regulator_init_data wm8350_dcdc6_data = {
+ .constraints = {
+ .name = "PVDD_ARM",
+ .min_uV = 1000000,
+ .max_uV = 1300000,
+ .always_on = 1,
+ .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE,
+ },
+ .num_consumer_supplies = ARRAY_SIZE(dcdc6_consumers),
+ .consumer_supplies = dcdc6_consumers,
+};
+
+/* Alive */
+static struct regulator_init_data wm8350_ldo1_data = {
+ .constraints = {
+ .name = "PVDD_ALIVE",
+ .min_uV = 1200000,
+ .max_uV = 1200000,
+ .always_on = 1,
+ .apply_uV = 1,
+ },
+};
+
+/* OTG */
+static struct regulator_init_data wm8350_ldo2_data = {
+ .constraints = {
+ .name = "PVDD_OTG",
+ .min_uV = 3300000,
+ .max_uV = 3300000,
+ .always_on = 1,
+ },
+};
+
+/* LCD */
+static struct regulator_init_data wm8350_ldo3_data = {
+ .constraints = {
+ .name = "PVDD_LCD",
+ .min_uV = 3000000,
+ .max_uV = 3000000,
+ .always_on = 1,
+ },
+};
+
+/* OTGi/1190-EV1 HPVDD & AVDD */
+static struct regulator_init_data wm8350_ldo4_data = {
+ .constraints = {
+ .name = "PVDD_OTGI/HPVDD/AVDD",
+ .min_uV = 1200000,
+ .max_uV = 1200000,
+ .apply_uV = 1,
+ .always_on = 1,
+ },
+};
+
+static struct {
+ int regulator;
+ struct regulator_init_data *initdata;
+} wm1190_regulators[] = {
+ { WM8350_DCDC_1, &wm8350_dcdc1_data },
+ { WM8350_DCDC_3, &wm8350_dcdc3_data },
+ { WM8350_DCDC_4, &wm8350_dcdc4_data },
+ { WM8350_DCDC_6, &wm8350_dcdc6_data },
+ { WM8350_LDO_1, &wm8350_ldo1_data },
+ { WM8350_LDO_2, &wm8350_ldo2_data },
+ { WM8350_LDO_3, &wm8350_ldo3_data },
+ { WM8350_LDO_4, &wm8350_ldo4_data },
+};
+
+static int __init smdk6410_wm8350_init(struct wm8350 *wm8350)
+{
+ int i;
+
+ /* Instantiate the regulators */
+ for (i = 0; i < ARRAY_SIZE(wm1190_regulators); i++)
+ wm8350_register_regulator(wm8350,
+ wm1190_regulators[i].regulator,
+ wm1190_regulators[i].initdata);
+
+ return 0;
+}
+
+static struct wm8350_platform_data __initdata smdk6410_wm8350_pdata = {
+ .init = smdk6410_wm8350_init,
+ .irq_high = 1,
+};
+#endif
+
static struct i2c_board_info i2c_devs0[] __initdata = {
{ I2C_BOARD_INFO("24c08", 0x50), },
{ I2C_BOARD_INFO("wm8580", 0x1b), },
+
+#ifdef CONFIG_SMDK6410_WM1190_EV1
+ { I2C_BOARD_INFO("wm8350", 0x1a),
+ .platform_data = &smdk6410_wm8350_pdata,
+ .irq = S3C_EINT(12),
+ },
+#endif
};
static struct i2c_board_info i2c_devs1[] __initdata = {
@@ -155,9 +339,23 @@
static void __init smdk6410_map_io(void)
{
+ u32 tmp;
+
s3c64xx_init_io(smdk6410_iodesc, ARRAY_SIZE(smdk6410_iodesc));
s3c24xx_init_clocks(12000000);
s3c24xx_init_uarts(smdk6410_uartcfgs, ARRAY_SIZE(smdk6410_uartcfgs));
+
+ /* set the LCD type */
+
+ tmp = __raw_readl(S3C64XX_SPCON);
+ tmp &= ~S3C64XX_SPCON_LCD_SEL_MASK;
+ tmp |= S3C64XX_SPCON_LCD_SEL_RGB;
+ __raw_writel(tmp, S3C64XX_SPCON);
+
+ /* remove the lcd bypass */
+ tmp = __raw_readl(S3C64XX_MODEM_MIFPCON);
+ tmp &= ~MIFPCON_LCD_BYPASS;
+ __raw_writel(tmp, S3C64XX_MODEM_MIFPCON);
}
static void __init smdk6410_machine_init(void)
diff --git a/arch/arm/mach-s3c6410/setup-sdhci.c b/arch/arm/mach-s3c6410/setup-sdhci.c
index 0b5788b..20666f3 100644
--- a/arch/arm/mach-s3c6410/setup-sdhci.c
+++ b/arch/arm/mach-s3c6410/setup-sdhci.c
@@ -21,8 +21,6 @@
#include <linux/mmc/card.h>
#include <linux/mmc/host.h>
-#include <mach/gpio.h>
-#include <plat/gpio-cfg.h>
#include <plat/regs-sdhci.h>
#include <plat/sdhci.h>
@@ -35,22 +33,6 @@
/* [3] = "48m", - note not succesfully used yet */
};
-void s3c6410_setup_sdhci0_cfg_gpio(struct platform_device *dev, int width)
-{
- unsigned int gpio;
- unsigned int end;
-
- end = S3C64XX_GPG(2 + width);
-
- /* Set all the necessary GPG pins to special-function 0 */
- for (gpio = S3C64XX_GPG(0); gpio < end; gpio++) {
- s3c_gpio_cfgpin(gpio, S3C_GPIO_SFN(2));
- s3c_gpio_setpull(gpio, S3C_GPIO_PULL_NONE);
- }
-
- s3c_gpio_setpull(S3C64XX_GPG(6), S3C_GPIO_PULL_UP);
- s3c_gpio_cfgpin(S3C64XX_GPG(6), S3C_GPIO_SFN(2));
-}
void s3c6410_setup_sdhci0_cfg_card(struct platform_device *dev,
void __iomem *r,
@@ -84,19 +66,3 @@
writel(ctrl3, r + S3C_SDHCI_CONTROL3);
}
-void s3c6410_setup_sdhci1_cfg_gpio(struct platform_device *dev, int width)
-{
- unsigned int gpio;
- unsigned int end;
-
- end = S3C64XX_GPH(2 + width);
-
- /* Set all the necessary GPG pins to special-function 0 */
- for (gpio = S3C64XX_GPH(0); gpio < end; gpio++) {
- s3c_gpio_cfgpin(gpio, S3C_GPIO_SFN(2));
- s3c_gpio_setpull(gpio, S3C_GPIO_PULL_NONE);
- }
-
- s3c_gpio_setpull(S3C64XX_GPG(6), S3C_GPIO_PULL_UP);
- s3c_gpio_cfgpin(S3C64XX_GPG(6), S3C_GPIO_SFN(3));
-}
diff --git a/arch/arm/mach-versatile/core.c b/arch/arm/mach-versatile/core.c
index b3bebcc..69214fc 100644
--- a/arch/arm/mach-versatile/core.c
+++ b/arch/arm/mach-versatile/core.c
@@ -116,7 +116,7 @@
{
unsigned int i;
- vic_init(VA_VIC_BASE, IRQ_VIC_START, ~0);
+ vic_init(VA_VIC_BASE, IRQ_VIC_START, ~0, 0);
set_irq_chained_handler(IRQ_VICSOURCE31, sic_handle_irq);
diff --git a/arch/arm/plat-s3c/Kconfig b/arch/arm/plat-s3c/Kconfig
index de93838..935c755 100644
--- a/arch/arm/plat-s3c/Kconfig
+++ b/arch/arm/plat-s3c/Kconfig
@@ -71,6 +71,15 @@
Resume code. See <file:Documentation/arm/Samsung-S3C24XX/Suspend.txt>
for more information.
+config S3C_PM_DEBUG_LED_SMDK
+ bool "SMDK LED suspend/resume debugging"
+ depends on PM && (MACH_SMDK6410)
+ help
+ Say Y here to enable the use of the SMDK LEDs on the baseboard
+ for debugging of the state of the suspend and resume process.
+
+ Note, this currently only works for S3C64XX based SMDK boards.
+
config S3C2410_PM_CHECK
bool "S3C2410 PM Suspend Memory CRC"
depends on PM && CRC32
@@ -150,6 +159,13 @@
Internal configuration to enable S3C64XX style GPIO configuration
functions.
+# DMA
+
+config S3C_DMA
+ bool
+ help
+ Internal configuration for S3C DMA core
+
# device definitions to compile in
config S3C_DEV_HSMMC
@@ -172,4 +188,14 @@
help
Compile in platform device definition for framebuffer
+config S3C_DEV_USB_HOST
+ bool
+ help
+ Compile in platform device definition for USB host.
+
+config S3C_DEV_USB_HSOTG
+ bool
+ help
+ Compile in platform device definition for USB high-speed OtG
+
endif
diff --git a/arch/arm/plat-s3c/Makefile b/arch/arm/plat-s3c/Makefile
index 8d7815d..6106514 100644
--- a/arch/arm/plat-s3c/Makefile
+++ b/arch/arm/plat-s3c/Makefile
@@ -18,9 +18,14 @@
obj-y += gpio.o
obj-y += gpio-config.o
+# DMA support
+
+obj-$(CONFIG_S3C_DMA) += dma.o
+
# PM support
obj-$(CONFIG_PM) += pm.o
+obj-$(CONFIG_PM) += pm-gpio.o
obj-$(CONFIG_S3C2410_PM_CHECK) += pm-check.o
# devices
@@ -30,3 +35,5 @@
obj-y += dev-i2c0.o
obj-$(CONFIG_S3C_DEV_I2C1) += dev-i2c1.o
obj-$(CONFIG_S3C_DEV_FB) += dev-fb.o
+obj-$(CONFIG_S3C_DEV_USB_HOST) += dev-usb.o
+obj-$(CONFIG_S3C_DEV_USB_HSOTG) += dev-usb-hsotg.o
diff --git a/arch/arm/plat-s3c/dev-usb-hsotg.c b/arch/arm/plat-s3c/dev-usb-hsotg.c
new file mode 100644
index 0000000..e2f604b
--- /dev/null
+++ b/arch/arm/plat-s3c/dev-usb-hsotg.c
@@ -0,0 +1,41 @@
+/* linux/arch/arm/plat-s3c/dev-usb-hsotg.c
+ *
+ * Copyright 2008 Simtec Electronics
+ * Ben Dooks <ben@simtec.co.uk>
+ * http://armlinux.simtec.co.uk/
+ *
+ * S3C series device definition for USB high-speed UDC/OtG block
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/kernel.h>
+#include <linux/string.h>
+#include <linux/platform_device.h>
+
+#include <mach/irqs.h>
+#include <mach/map.h>
+
+#include <plat/devs.h>
+
+static struct resource s3c_usb_hsotg_resources[] = {
+ [0] = {
+ .start = S3C_PA_USB_HSOTG,
+ .end = S3C_PA_USB_HSOTG + 0x10000 - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = IRQ_OTG,
+ .end = IRQ_OTG,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+struct platform_device s3c_device_usb_hsotg = {
+ .name = "s3c-hsotg",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(s3c_usb_hsotg_resources),
+ .resource = s3c_usb_hsotg_resources,
+};
diff --git a/arch/arm/plat-s3c/dev-usb.c b/arch/arm/plat-s3c/dev-usb.c
new file mode 100644
index 0000000..2ee85ab
--- /dev/null
+++ b/arch/arm/plat-s3c/dev-usb.c
@@ -0,0 +1,50 @@
+/* linux/arch/arm/plat-s3c/dev-usb.c
+ *
+ * Copyright 2008 Simtec Electronics
+ * Ben Dooks <ben@simtec.co.uk>
+ * http://armlinux.simtec.co.uk/
+ *
+ * S3C series device definition for USB host
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/kernel.h>
+#include <linux/string.h>
+#include <linux/platform_device.h>
+
+#include <mach/irqs.h>
+#include <mach/map.h>
+
+#include <plat/devs.h>
+
+
+static struct resource s3c_usb_resource[] = {
+ [0] = {
+ .start = S3C_PA_USBHOST,
+ .end = S3C_PA_USBHOST + 0x100 - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = IRQ_USBH,
+ .end = IRQ_USBH,
+ .flags = IORESOURCE_IRQ,
+ }
+};
+
+static u64 s3c_device_usb_dmamask = 0xffffffffUL;
+
+struct platform_device s3c_device_usb = {
+ .name = "s3c2410-ohci",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(s3c_usb_resource),
+ .resource = s3c_usb_resource,
+ .dev = {
+ .dma_mask = &s3c_device_usb_dmamask,
+ .coherent_dma_mask = 0xffffffffUL
+ }
+};
+
+EXPORT_SYMBOL(s3c_device_usb);
diff --git a/arch/arm/plat-s3c/dma.c b/arch/arm/plat-s3c/dma.c
new file mode 100644
index 0000000..c9db75c
--- /dev/null
+++ b/arch/arm/plat-s3c/dma.c
@@ -0,0 +1,86 @@
+/* linux/arch/arm/plat-s3c/dma.c
+ *
+ * Copyright (c) 2003-2005,2006,2009 Simtec Electronics
+ * Ben Dooks <ben@simtec.co.uk>
+ * http://armlinux.simtec.co.uk/
+ *
+ * S3C DMA core
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+struct s3c2410_dma_buf;
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/errno.h>
+
+#include <mach/dma.h>
+#include <mach/irqs.h>
+
+#include <plat/dma-plat.h>
+
+/* dma channel state information */
+struct s3c2410_dma_chan s3c2410_chans[S3C_DMA_CHANNELS];
+struct s3c2410_dma_chan *s3c_dma_chan_map[DMACH_MAX];
+
+/* s3c_dma_lookup_channel
+ *
+ * change the dma channel number given into a real dma channel id
+*/
+
+struct s3c2410_dma_chan *s3c_dma_lookup_channel(unsigned int channel)
+{
+ if (channel & DMACH_LOW_LEVEL)
+ return &s3c2410_chans[channel & ~DMACH_LOW_LEVEL];
+ else
+ return s3c_dma_chan_map[channel];
+}
+
+/* do we need to protect the settings of the fields from
+ * irq?
+*/
+
+int s3c2410_dma_set_opfn(unsigned int channel, s3c2410_dma_opfn_t rtn)
+{
+ struct s3c2410_dma_chan *chan = s3c_dma_lookup_channel(channel);
+
+ if (chan == NULL)
+ return -EINVAL;
+
+ pr_debug("%s: chan=%p, op rtn=%p\n", __func__, chan, rtn);
+
+ chan->op_fn = rtn;
+
+ return 0;
+}
+EXPORT_SYMBOL(s3c2410_dma_set_opfn);
+
+int s3c2410_dma_set_buffdone_fn(unsigned int channel, s3c2410_dma_cbfn_t rtn)
+{
+ struct s3c2410_dma_chan *chan = s3c_dma_lookup_channel(channel);
+
+ if (chan == NULL)
+ return -EINVAL;
+
+ pr_debug("%s: chan=%p, callback rtn=%p\n", __func__, chan, rtn);
+
+ chan->callback_fn = rtn;
+
+ return 0;
+}
+EXPORT_SYMBOL(s3c2410_dma_set_buffdone_fn);
+
+int s3c2410_dma_setflags(unsigned int channel, unsigned int flags)
+{
+ struct s3c2410_dma_chan *chan = s3c_dma_lookup_channel(channel);
+
+ if (chan == NULL)
+ return -EINVAL;
+
+ chan->flags = flags;
+ return 0;
+}
+EXPORT_SYMBOL(s3c2410_dma_setflags);
diff --git a/arch/arm/plat-s3c/gpio.c b/arch/arm/plat-s3c/gpio.c
index d71dd6d..260fdc6 100644
--- a/arch/arm/plat-s3c/gpio.c
+++ b/arch/arm/plat-s3c/gpio.c
@@ -16,7 +16,7 @@
#include <linux/io.h>
#include <linux/gpio.h>
-#include <plat/gpio-core.h>
+#include <mach/gpio-core.h>
#ifdef CONFIG_S3C_GPIO_TRACK
struct s3c_gpio_chip *s3c_gpios[S3C_GPIO_END];
@@ -140,6 +140,15 @@
if (!gc->get)
gc->get = s3c_gpiolib_get;
+#ifdef CONFIG_PM
+ if (chip->pm != NULL) {
+ if (!chip->pm->save || !chip->pm->resume)
+ printk(KERN_ERR "gpio: %s has missing PM functions\n",
+ gc->label);
+ } else
+ printk(KERN_ERR "gpio: %s has no PM function\n", gc->label);
+#endif
+
/* gpiochip_add() prints own failure message on error. */
ret = gpiochip_add(gc);
if (ret >= 0)
diff --git a/arch/arm/plat-s3c/include/plat/adc.h b/arch/arm/plat-s3c/include/plat/adc.h
index 43df2a4..d847bd4 100644
--- a/arch/arm/plat-s3c/include/plat/adc.h
+++ b/arch/arm/plat-s3c/include/plat/adc.h
@@ -19,10 +19,12 @@
extern int s3c_adc_start(struct s3c_adc_client *client,
unsigned int channel, unsigned int nr_samples);
-extern struct s3c_adc_client *s3c_adc_register(struct platform_device *pdev,
- void (*select)(unsigned selected),
- void (*conv)(unsigned d0, unsigned d1),
- unsigned int is_ts);
+extern struct s3c_adc_client *
+ s3c_adc_register(struct platform_device *pdev,
+ void (*select)(unsigned selected),
+ void (*conv)(unsigned d0, unsigned d1,
+ unsigned *samples_left),
+ unsigned int is_ts);
extern void s3c_adc_release(struct s3c_adc_client *client);
diff --git a/arch/arm/plat-s3c/include/plat/clock.h b/arch/arm/plat-s3c/include/plat/clock.h
index a10622e..d86af84 100644
--- a/arch/arm/plat-s3c/include/plat/clock.h
+++ b/arch/arm/plat-s3c/include/plat/clock.h
@@ -50,6 +50,7 @@
extern struct clk clk_ext;
/* S3C64XX specific clocks */
+extern struct clk clk_h2;
extern struct clk clk_27m;
extern struct clk clk_48m;
diff --git a/arch/arm/plat-s3c/include/plat/cpu.h b/arch/arm/plat-s3c/include/plat/cpu.h
index e62ae0f..be541cb 100644
--- a/arch/arm/plat-s3c/include/plat/cpu.h
+++ b/arch/arm/plat-s3c/include/plat/cpu.h
@@ -69,3 +69,6 @@
extern struct sysdev_class s3c2440_sysclass;
extern struct sysdev_class s3c2442_sysclass;
extern struct sysdev_class s3c2443_sysclass;
+extern struct sysdev_class s3c6410_sysclass;
+extern struct sysdev_class s3c64xx_sysclass;
+
diff --git a/arch/arm/plat-s3c/include/plat/devs.h b/arch/arm/plat-s3c/include/plat/devs.h
index 26f0cec..a0b6768 100644
--- a/arch/arm/plat-s3c/include/plat/devs.h
+++ b/arch/arm/plat-s3c/include/plat/devs.h
@@ -45,6 +45,7 @@
extern struct platform_device s3c_device_nand;
extern struct platform_device s3c_device_usbgadget;
+extern struct platform_device s3c_device_usb_hsotg;
/* s3c2440 specific devices */
diff --git a/arch/arm/plat-s3c/include/plat/dma-core.h b/arch/arm/plat-s3c/include/plat/dma-core.h
new file mode 100644
index 0000000..32ff2a9
--- /dev/null
+++ b/arch/arm/plat-s3c/include/plat/dma-core.h
@@ -0,0 +1,22 @@
+/* arch/arm/plat-s3c/include/plat/dma.h
+ *
+ * Copyright 2008 Openmoko, Inc.
+ * Copyright 2008 Simtec Electronics
+ * Ben Dooks <ben@simtec.co.uk>
+ * http://armlinux.simtec.co.uk/
+ *
+ * Samsung S3C DMA core support
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+extern struct s3c2410_dma_chan *s3c_dma_lookup_channel(unsigned int channel);
+
+extern struct s3c2410_dma_chan *s3c_dma_chan_map[];
+
+/* the currently allocated channel information */
+extern struct s3c2410_dma_chan s3c2410_chans[];
+
+
diff --git a/arch/arm/plat-s3c/include/plat/dma.h b/arch/arm/plat-s3c/include/plat/dma.h
new file mode 100644
index 0000000..34dba98
--- /dev/null
+++ b/arch/arm/plat-s3c/include/plat/dma.h
@@ -0,0 +1,127 @@
+/* arch/arm/plat-s3c/include/plat/dma.h
+ *
+ * Copyright (C) 2003,2004,2006 Simtec Electronics
+ * Ben Dooks <ben@simtec.co.uk>
+ *
+ * Samsung S3C DMA support
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+enum s3c2410_dma_buffresult {
+ S3C2410_RES_OK,
+ S3C2410_RES_ERR,
+ S3C2410_RES_ABORT
+};
+
+enum s3c2410_dmasrc {
+ S3C2410_DMASRC_HW, /* source is memory */
+ S3C2410_DMASRC_MEM /* source is hardware */
+};
+
+/* enum s3c2410_chan_op
+ *
+ * operation codes passed to the DMA code by the user, and also used
+ * to inform the current channel owner of any changes to the system state
+*/
+
+enum s3c2410_chan_op {
+ S3C2410_DMAOP_START,
+ S3C2410_DMAOP_STOP,
+ S3C2410_DMAOP_PAUSE,
+ S3C2410_DMAOP_RESUME,
+ S3C2410_DMAOP_FLUSH,
+ S3C2410_DMAOP_TIMEOUT, /* internal signal to handler */
+ S3C2410_DMAOP_STARTED, /* indicate channel started */
+};
+
+struct s3c2410_dma_client {
+ char *name;
+};
+
+struct s3c2410_dma_chan;
+
+/* s3c2410_dma_cbfn_t
+ *
+ * buffer callback routine type
+*/
+
+typedef void (*s3c2410_dma_cbfn_t)(struct s3c2410_dma_chan *,
+ void *buf, int size,
+ enum s3c2410_dma_buffresult result);
+
+typedef int (*s3c2410_dma_opfn_t)(struct s3c2410_dma_chan *,
+ enum s3c2410_chan_op );
+
+
+
+/* s3c2410_dma_request
+ *
+ * request a dma channel exclusivley
+*/
+
+extern int s3c2410_dma_request(unsigned int channel,
+ struct s3c2410_dma_client *, void *dev);
+
+
+/* s3c2410_dma_ctrl
+ *
+ * change the state of the dma channel
+*/
+
+extern int s3c2410_dma_ctrl(unsigned int channel, enum s3c2410_chan_op op);
+
+/* s3c2410_dma_setflags
+ *
+ * set the channel's flags to a given state
+*/
+
+extern int s3c2410_dma_setflags(unsigned int channel,
+ unsigned int flags);
+
+/* s3c2410_dma_free
+ *
+ * free the dma channel (will also abort any outstanding operations)
+*/
+
+extern int s3c2410_dma_free(unsigned int channel, struct s3c2410_dma_client *);
+
+/* s3c2410_dma_enqueue
+ *
+ * place the given buffer onto the queue of operations for the channel.
+ * The buffer must be allocated from dma coherent memory, or the Dcache/WB
+ * drained before the buffer is given to the DMA system.
+*/
+
+extern int s3c2410_dma_enqueue(unsigned int channel, void *id,
+ dma_addr_t data, int size);
+
+/* s3c2410_dma_config
+ *
+ * configure the dma channel
+*/
+
+extern int s3c2410_dma_config(unsigned int channel, int xferunit);
+
+/* s3c2410_dma_devconfig
+ *
+ * configure the device we're talking to
+*/
+
+extern int s3c2410_dma_devconfig(int channel, enum s3c2410_dmasrc source,
+ unsigned long devaddr);
+
+/* s3c2410_dma_getposition
+ *
+ * get the position that the dma transfer is currently at
+*/
+
+extern int s3c2410_dma_getposition(unsigned int channel,
+ dma_addr_t *src, dma_addr_t *dest);
+
+extern int s3c2410_dma_set_opfn(unsigned int, s3c2410_dma_opfn_t rtn);
+extern int s3c2410_dma_set_buffdone_fn(unsigned int, s3c2410_dma_cbfn_t rtn);
+
+
diff --git a/arch/arm/plat-s3c/include/plat/gpio-core.h b/arch/arm/plat-s3c/include/plat/gpio-core.h
index 2fc60a5..32af612 100644
--- a/arch/arm/plat-s3c/include/plat/gpio-core.h
+++ b/arch/arm/plat-s3c/include/plat/gpio-core.h
@@ -20,6 +20,18 @@
* specific code.
*/
+struct s3c_gpio_chip;
+
+/**
+ * struct s3c_gpio_pm - power management (suspend/resume) information
+ * @save: Routine to save the state of the GPIO block
+ * @resume: Routine to resume the GPIO block.
+ */
+struct s3c_gpio_pm {
+ void (*save)(struct s3c_gpio_chip *chip);
+ void (*resume)(struct s3c_gpio_chip *chip);
+};
+
struct s3c_gpio_cfg;
/**
@@ -27,6 +39,7 @@
* @chip: The chip structure to be exported via gpiolib.
* @base: The base pointer to the gpio configuration registers.
* @config: special function and pull-resistor control information.
+ * @pm_save: Save information for suspend/resume support.
*
* This wrapper provides the necessary information for the Samsung
* specific gpios being registered with gpiolib.
@@ -34,7 +47,11 @@
struct s3c_gpio_chip {
struct gpio_chip chip;
struct s3c_gpio_cfg *config;
+ struct s3c_gpio_pm *pm;
void __iomem *base;
+#ifdef CONFIG_PM
+ u32 pm_save[4];
+#endif
};
static inline struct s3c_gpio_chip *to_s3c_gpio(struct gpio_chip *gpc)
@@ -75,3 +92,16 @@
static inline void s3c_gpiolib_track(struct s3c_gpio_chip *chip) { }
#endif
+
+#ifdef CONFIG_PM
+extern struct s3c_gpio_pm s3c_gpio_pm_1bit;
+extern struct s3c_gpio_pm s3c_gpio_pm_2bit;
+extern struct s3c_gpio_pm s3c_gpio_pm_4bit;
+#define __gpio_pm(x) x
+#else
+#define s3c_gpio_pm_1bit NULL
+#define s3c_gpio_pm_2bit NULL
+#define s3c_gpio_pm_4bit NULL
+#define __gpio_pm(x) NULL
+
+#endif /* CONFIG_PM */
diff --git a/arch/arm/plat-s3c/include/plat/pm.h b/arch/arm/plat-s3c/include/plat/pm.h
index 3779775..7a79719 100644
--- a/arch/arm/plat-s3c/include/plat/pm.h
+++ b/arch/arm/plat-s3c/include/plat/pm.h
@@ -44,6 +44,8 @@
extern unsigned long s3c_pm_flags;
+extern unsigned char pm_uart_udivslot; /* true to save UART UDIVSLOT */
+
/* from sleep.S */
extern int s3c_cpu_save(unsigned long *saveblk);
@@ -88,6 +90,7 @@
u32 ufcon;
u32 umcon;
u32 ubrdiv;
+ u32 udivslot;
};
/* helper functions to save/restore lists of registers. */
@@ -124,6 +127,18 @@
#define S3C_PMDBG(fmt...) printk(KERN_DEBUG fmt)
#endif
+#ifdef CONFIG_S3C_PM_DEBUG_LED_SMDK
+/**
+ * s3c_pm_debug_smdkled() - Debug PM suspend/resume via SMDK Board LEDs
+ * @set: set bits for the state of the LEDs
+ * @clear: clear bits for the state of the LEDs.
+ */
+extern void s3c_pm_debug_smdkled(u32 set, u32 clear);
+
+#else
+static inline void s3c_pm_debug_smdkled(u32 set, u32 clear) { }
+#endif /* CONFIG_S3C_PM_DEBUG_LED_SMDK */
+
/* suspend memory checking */
#ifdef CONFIG_S3C2410_PM_CHECK
diff --git a/arch/arm/plat-s3c/include/plat/regs-serial.h b/arch/arm/plat-s3c/include/plat/regs-serial.h
index 487d7d2..66af75a 100644
--- a/arch/arm/plat-s3c/include/plat/regs-serial.h
+++ b/arch/arm/plat-s3c/include/plat/regs-serial.h
@@ -189,6 +189,11 @@
#define S3C2443_DIVSLOT (0x2C)
+/* S3C64XX interrupt registers. */
+#define S3C64XX_UINTP 0x30
+#define S3C64XX_UINTSP 0x34
+#define S3C64XX_UINTM 0x38
+
#ifndef __ASSEMBLY__
/* struct s3c24xx_uart_clksrc
diff --git a/arch/arm/plat-s3c/include/plat/sdhci.h b/arch/arm/plat-s3c/include/plat/sdhci.h
index c4ca392..f615308 100644
--- a/arch/arm/plat-s3c/include/plat/sdhci.h
+++ b/arch/arm/plat-s3c/include/plat/sdhci.h
@@ -67,12 +67,52 @@
/* Helper function availablity */
+extern void s3c64xx_setup_sdhci0_cfg_gpio(struct platform_device *, int w);
+extern void s3c64xx_setup_sdhci1_cfg_gpio(struct platform_device *, int w);
+
+/* S3C6400 SDHCI setup */
+
+#ifdef CONFIG_S3C6400_SETUP_SDHCI
+extern char *s3c6400_hsmmc_clksrcs[4];
+
+#ifdef CONFIG_S3C_DEV_HSMMC
+extern void s3c6400_setup_sdhci_cfg_card(struct platform_device *dev,
+ void __iomem *r,
+ struct mmc_ios *ios,
+ struct mmc_card *card);
+
+static inline void s3c6400_default_sdhci0(void)
+{
+ s3c_hsmmc0_def_platdata.clocks = s3c6400_hsmmc_clksrcs;
+ s3c_hsmmc0_def_platdata.cfg_gpio = s3c64xx_setup_sdhci0_cfg_gpio;
+ s3c_hsmmc0_def_platdata.cfg_card = s3c6400_setup_sdhci_cfg_card;
+}
+
+#else
+static inline void s3c6400_default_sdhci0(void) { }
+#endif /* CONFIG_S3C_DEV_HSMMC */
+
+#ifdef CONFIG_S3C_DEV_HSMMC1
+static inline void s3c6400_default_sdhci1(void)
+{
+ s3c_hsmmc1_def_platdata.clocks = s3c6400_hsmmc_clksrcs;
+ s3c_hsmmc1_def_platdata.cfg_gpio = s3c64xx_setup_sdhci1_cfg_gpio;
+ s3c_hsmmc1_def_platdata.cfg_card = s3c6400_setup_sdhci_cfg_card;
+}
+#else
+static inline void s3c6400_default_sdhci1(void) { }
+#endif /* CONFIG_S3C_DEV_HSMMC1 */
+
+#else
+static inline void s3c6400_default_sdhci0(void) { }
+static inline void s3c6400_default_sdhci1(void) { }
+#endif /* CONFIG_S3C6400_SETUP_SDHCI */
+
+/* S3C6410 SDHCI setup */
+
#ifdef CONFIG_S3C6410_SETUP_SDHCI
extern char *s3c6410_hsmmc_clksrcs[4];
-extern void s3c6410_setup_sdhci0_cfg_gpio(struct platform_device *, int w);
-extern void s3c6410_setup_sdhci1_cfg_gpio(struct platform_device *, int w);
-
extern void s3c6410_setup_sdhci0_cfg_card(struct platform_device *dev,
void __iomem *r,
struct mmc_ios *ios,
@@ -82,7 +122,7 @@
static inline void s3c6410_default_sdhci0(void)
{
s3c_hsmmc0_def_platdata.clocks = s3c6410_hsmmc_clksrcs;
- s3c_hsmmc0_def_platdata.cfg_gpio = s3c6410_setup_sdhci0_cfg_gpio;
+ s3c_hsmmc0_def_platdata.cfg_gpio = s3c64xx_setup_sdhci0_cfg_gpio;
s3c_hsmmc0_def_platdata.cfg_card = s3c6410_setup_sdhci0_cfg_card;
}
#else
@@ -93,7 +133,7 @@
static inline void s3c6410_default_sdhci1(void)
{
s3c_hsmmc1_def_platdata.clocks = s3c6410_hsmmc_clksrcs;
- s3c_hsmmc1_def_platdata.cfg_gpio = s3c6410_setup_sdhci1_cfg_gpio;
+ s3c_hsmmc1_def_platdata.cfg_gpio = s3c64xx_setup_sdhci1_cfg_gpio;
s3c_hsmmc1_def_platdata.cfg_card = s3c6410_setup_sdhci0_cfg_card;
}
#else
diff --git a/arch/arm/plat-s3c/include/plat/udc-hs.h b/arch/arm/plat-s3c/include/plat/udc-hs.h
new file mode 100644
index 0000000..dd04db0
--- /dev/null
+++ b/arch/arm/plat-s3c/include/plat/udc-hs.h
@@ -0,0 +1,29 @@
+/* arch/arm/plat-s3c/include/plat/udc-hs.h
+ *
+ * Copyright 2008 Openmoko, Inc.
+ * Copyright 2008 Simtec Electronics
+ * Ben Dooks <ben@simtec.co.uk>
+ * http://armlinux.simtec.co.uk/
+ *
+ * S3C USB2.0 High-speed / OtG platform information
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+enum s3c_hostg_dmamode {
+ S3C_HSOTG_DMA_NONE, /* do not use DMA at-all */
+ S3C_HSOTG_DMA_ONLY, /* always use DMA */
+ S3C_HSOTG_DMA_DRV, /* DMA is chosen by driver */
+};
+
+/**
+ * struct s3c_hsotg_plat - platform data for high-speed otg/udc
+ * @dma: Whether to use DMA or not.
+ * @is_osc: The clock source is an oscillator, not a crystal
+ */
+struct s3c_hsotg_plat {
+ enum s3c_hostg_dmamode dma;
+ unsigned int is_osc : 1;
+};
diff --git a/arch/arm/plat-s3c/include/plat/watchdog-reset.h b/arch/arm/plat-s3c/include/plat/watchdog-reset.h
new file mode 100644
index 0000000..54b762a
--- /dev/null
+++ b/arch/arm/plat-s3c/include/plat/watchdog-reset.h
@@ -0,0 +1,49 @@
+/* arch/arm/plat-s3c/include/plat/watchdog-reset.h
+ *
+ * Copyright (c) 2008 Simtec Electronics
+ * Ben Dooks <ben@simtec.co.uk>
+ *
+ * S3C2410 - System define for arch_reset() function
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <plat/regs-watchdog.h>
+#include <mach/map.h>
+
+#include <linux/clk.h>
+#include <linux/err.h>
+#include <linux/io.h>
+
+static inline void arch_wdt_reset(void)
+{
+ struct clk *wdtclk;
+
+ printk("arch_reset: attempting watchdog reset\n");
+
+ __raw_writel(0, S3C2410_WTCON); /* disable watchdog, to be safe */
+
+ wdtclk = clk_get(NULL, "watchdog");
+ if (!IS_ERR(wdtclk)) {
+ clk_enable(wdtclk);
+ } else
+ printk(KERN_WARNING "%s: warning: cannot get watchdog clock\n", __func__);
+
+ /* put initial values into count and data */
+ __raw_writel(0x80, S3C2410_WTCNT);
+ __raw_writel(0x80, S3C2410_WTDAT);
+
+ /* set the watchdog to go and reset... */
+ __raw_writel(S3C2410_WTCON_ENABLE|S3C2410_WTCON_DIV16|S3C2410_WTCON_RSTEN |
+ S3C2410_WTCON_PRESCALE(0x20), S3C2410_WTCON);
+
+ /* wait for reset to assert... */
+ mdelay(500);
+
+ printk(KERN_ERR "Watchdog reset failed to assert reset\n");
+
+ /* delay to allow the serial port to show the message */
+ mdelay(50);
+}
diff --git a/arch/arm/plat-s3c/pm-gpio.c b/arch/arm/plat-s3c/pm-gpio.c
new file mode 100644
index 0000000..cfd326a
--- /dev/null
+++ b/arch/arm/plat-s3c/pm-gpio.c
@@ -0,0 +1,380 @@
+
+/* linux/arch/arm/plat-s3c/pm-gpio.c
+ *
+ * Copyright 2008 Openmoko, Inc.
+ * Copyright 2008 Simtec Electronics
+ * Ben Dooks <ben@simtec.co.uk>
+ * http://armlinux.simtec.co.uk/
+ *
+ * S3C series GPIO PM code
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/kernel.h>
+#include <linux/sysdev.h>
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/gpio.h>
+
+#include <mach/gpio-core.h>
+#include <plat/pm.h>
+
+/* PM GPIO helpers */
+
+#define OFFS_CON (0x00)
+#define OFFS_DAT (0x04)
+#define OFFS_UP (0x08)
+
+static void s3c_gpio_pm_1bit_save(struct s3c_gpio_chip *chip)
+{
+ chip->pm_save[0] = __raw_readl(chip->base + OFFS_CON);
+ chip->pm_save[1] = __raw_readl(chip->base + OFFS_DAT);
+}
+
+static void s3c_gpio_pm_1bit_resume(struct s3c_gpio_chip *chip)
+{
+ void __iomem *base = chip->base;
+ u32 old_gpcon = __raw_readl(base + OFFS_CON);
+ u32 old_gpdat = __raw_readl(base + OFFS_DAT);
+ u32 gps_gpcon = chip->pm_save[0];
+ u32 gps_gpdat = chip->pm_save[1];
+ u32 gpcon;
+
+ /* GPACON only has one bit per control / data and no PULLUPs.
+ * GPACON[x] = 0 => Output, 1 => SFN */
+
+ /* first set all SFN bits to SFN */
+
+ gpcon = old_gpcon | gps_gpcon;
+ __raw_writel(gpcon, base + OFFS_CON);
+
+ /* now set all the other bits */
+
+ __raw_writel(gps_gpdat, base + OFFS_DAT);
+ __raw_writel(gps_gpcon, base + OFFS_CON);
+
+ S3C_PMDBG("%s: CON %08x => %08x, DAT %08x => %08x\n",
+ chip->chip.label, old_gpcon, gps_gpcon, old_gpdat, gps_gpdat);
+}
+
+struct s3c_gpio_pm s3c_gpio_pm_1bit = {
+ .save = s3c_gpio_pm_1bit_save,
+ .resume = s3c_gpio_pm_1bit_resume,
+};
+
+static void s3c_gpio_pm_2bit_save(struct s3c_gpio_chip *chip)
+{
+ chip->pm_save[0] = __raw_readl(chip->base + OFFS_CON);
+ chip->pm_save[1] = __raw_readl(chip->base + OFFS_DAT);
+ chip->pm_save[2] = __raw_readl(chip->base + OFFS_UP);
+}
+
+/* Test whether the given masked+shifted bits of an GPIO configuration
+ * are one of the SFN (special function) modes. */
+
+static inline int is_sfn(unsigned long con)
+{
+ return con >= 2;
+}
+
+/* Test if the given masked+shifted GPIO configuration is an input */
+
+static inline int is_in(unsigned long con)
+{
+ return con == 0;
+}
+
+/* Test if the given masked+shifted GPIO configuration is an output */
+
+static inline int is_out(unsigned long con)
+{
+ return con == 1;
+}
+
+/**
+ * s3c_gpio_pm_2bit_resume() - restore the given GPIO bank
+ * @chip: The chip information to resume.
+ *
+ * Restore one of the GPIO banks that was saved during suspend. This is
+ * not as simple as once thought, due to the possibility of glitches
+ * from the order that the CON and DAT registers are set in.
+ *
+ * The three states the pin can be are {IN,OUT,SFN} which gives us 9
+ * combinations of changes to check. Three of these, if the pin stays
+ * in the same configuration can be discounted. This leaves us with
+ * the following:
+ *
+ * { IN => OUT } Change DAT first
+ * { IN => SFN } Change CON first
+ * { OUT => SFN } Change CON first, so new data will not glitch
+ * { OUT => IN } Change CON first, so new data will not glitch
+ * { SFN => IN } Change CON first
+ * { SFN => OUT } Change DAT first, so new data will not glitch [1]
+ *
+ * We do not currently deal with the UP registers as these control
+ * weak resistors, so a small delay in change should not need to bring
+ * these into the calculations.
+ *
+ * [1] this assumes that writing to a pin DAT whilst in SFN will set the
+ * state for when it is next output.
+ */
+static void s3c_gpio_pm_2bit_resume(struct s3c_gpio_chip *chip)
+{
+ void __iomem *base = chip->base;
+ u32 old_gpcon = __raw_readl(base + OFFS_CON);
+ u32 old_gpdat = __raw_readl(base + OFFS_DAT);
+ u32 gps_gpcon = chip->pm_save[0];
+ u32 gps_gpdat = chip->pm_save[1];
+ u32 gpcon, old, new, mask;
+ u32 change_mask = 0x0;
+ int nr;
+
+ /* restore GPIO pull-up settings */
+ __raw_writel(chip->pm_save[2], base + OFFS_UP);
+
+ /* Create a change_mask of all the items that need to have
+ * their CON value changed before their DAT value, so that
+ * we minimise the work between the two settings.
+ */
+
+ for (nr = 0, mask = 0x03; nr < 32; nr += 2, mask <<= 2) {
+ old = (old_gpcon & mask) >> nr;
+ new = (gps_gpcon & mask) >> nr;
+
+ /* If there is no change, then skip */
+
+ if (old == new)
+ continue;
+
+ /* If both are special function, then skip */
+
+ if (is_sfn(old) && is_sfn(new))
+ continue;
+
+ /* Change is IN => OUT, do not change now */
+
+ if (is_in(old) && is_out(new))
+ continue;
+
+ /* Change is SFN => OUT, do not change now */
+
+ if (is_sfn(old) && is_out(new))
+ continue;
+
+ /* We should now be at the case of IN=>SFN,
+ * OUT=>SFN, OUT=>IN, SFN=>IN. */
+
+ change_mask |= mask;
+ }
+
+
+ /* Write the new CON settings */
+
+ gpcon = old_gpcon & ~change_mask;
+ gpcon |= gps_gpcon & change_mask;
+
+ __raw_writel(gpcon, base + OFFS_CON);
+
+ /* Now change any items that require DAT,CON */
+
+ __raw_writel(gps_gpdat, base + OFFS_DAT);
+ __raw_writel(gps_gpcon, base + OFFS_CON);
+
+ S3C_PMDBG("%s: CON %08x => %08x, DAT %08x => %08x\n",
+ chip->chip.label, old_gpcon, gps_gpcon, old_gpdat, gps_gpdat);
+}
+
+struct s3c_gpio_pm s3c_gpio_pm_2bit = {
+ .save = s3c_gpio_pm_2bit_save,
+ .resume = s3c_gpio_pm_2bit_resume,
+};
+
+#ifdef CONFIG_ARCH_S3C64XX
+static void s3c_gpio_pm_4bit_save(struct s3c_gpio_chip *chip)
+{
+ chip->pm_save[1] = __raw_readl(chip->base + OFFS_CON);
+ chip->pm_save[2] = __raw_readl(chip->base + OFFS_DAT);
+ chip->pm_save[3] = __raw_readl(chip->base + OFFS_UP);
+
+ if (chip->chip.ngpio > 8)
+ chip->pm_save[0] = __raw_readl(chip->base - 4);
+}
+
+static u32 s3c_gpio_pm_4bit_mask(u32 old_gpcon, u32 gps_gpcon)
+{
+ u32 old, new, mask;
+ u32 change_mask = 0x0;
+ int nr;
+
+ for (nr = 0, mask = 0x0f; nr < 16; nr += 4, mask <<= 4) {
+ old = (old_gpcon & mask) >> nr;
+ new = (gps_gpcon & mask) >> nr;
+
+ /* If there is no change, then skip */
+
+ if (old == new)
+ continue;
+
+ /* If both are special function, then skip */
+
+ if (is_sfn(old) && is_sfn(new))
+ continue;
+
+ /* Change is IN => OUT, do not change now */
+
+ if (is_in(old) && is_out(new))
+ continue;
+
+ /* Change is SFN => OUT, do not change now */
+
+ if (is_sfn(old) && is_out(new))
+ continue;
+
+ /* We should now be at the case of IN=>SFN,
+ * OUT=>SFN, OUT=>IN, SFN=>IN. */
+
+ change_mask |= mask;
+ }
+
+ return change_mask;
+}
+
+static void s3c_gpio_pm_4bit_con(struct s3c_gpio_chip *chip, int index)
+{
+ void __iomem *con = chip->base + (index * 4);
+ u32 old_gpcon = __raw_readl(con);
+ u32 gps_gpcon = chip->pm_save[index + 1];
+ u32 gpcon, mask;
+
+ mask = s3c_gpio_pm_4bit_mask(old_gpcon, gps_gpcon);
+
+ gpcon = old_gpcon & ~mask;
+ gpcon |= gps_gpcon & mask;
+
+ __raw_writel(gpcon, con);
+}
+
+static void s3c_gpio_pm_4bit_resume(struct s3c_gpio_chip *chip)
+{
+ void __iomem *base = chip->base;
+ u32 old_gpcon[2];
+ u32 old_gpdat = __raw_readl(base + OFFS_DAT);
+ u32 gps_gpdat = chip->pm_save[2];
+
+ /* First, modify the CON settings */
+
+ old_gpcon[0] = 0;
+ old_gpcon[1] = __raw_readl(base + OFFS_CON);
+
+ s3c_gpio_pm_4bit_con(chip, 0);
+ if (chip->chip.ngpio > 8) {
+ old_gpcon[0] = __raw_readl(base - 4);
+ s3c_gpio_pm_4bit_con(chip, -1);
+ }
+
+ /* Now change the configurations that require DAT,CON */
+
+ __raw_writel(chip->pm_save[2], base + OFFS_DAT);
+ __raw_writel(chip->pm_save[1], base + OFFS_CON);
+ if (chip->chip.ngpio > 8)
+ __raw_writel(chip->pm_save[0], base - 4);
+
+ __raw_writel(chip->pm_save[2], base + OFFS_DAT);
+ __raw_writel(chip->pm_save[3], base + OFFS_UP);
+
+ if (chip->chip.ngpio > 8) {
+ S3C_PMDBG("%s: CON4 %08x,%08x => %08x,%08x, DAT %08x => %08x\n",
+ chip->chip.label, old_gpcon[0], old_gpcon[1],
+ __raw_readl(base - 4),
+ __raw_readl(base + OFFS_CON),
+ old_gpdat, gps_gpdat);
+ } else
+ S3C_PMDBG("%s: CON4 %08x => %08x, DAT %08x => %08x\n",
+ chip->chip.label, old_gpcon[1],
+ __raw_readl(base + OFFS_CON),
+ old_gpdat, gps_gpdat);
+}
+
+struct s3c_gpio_pm s3c_gpio_pm_4bit = {
+ .save = s3c_gpio_pm_4bit_save,
+ .resume = s3c_gpio_pm_4bit_resume,
+};
+#endif /* CONFIG_ARCH_S3C64XX */
+
+/**
+ * s3c_pm_save_gpio() - save gpio chip data for suspend
+ * @ourchip: The chip for suspend.
+ */
+static void s3c_pm_save_gpio(struct s3c_gpio_chip *ourchip)
+{
+ struct s3c_gpio_pm *pm = ourchip->pm;
+
+ if (pm == NULL || pm->save == NULL)
+ S3C_PMDBG("%s: no pm for %s\n", __func__, ourchip->chip.label);
+ else
+ pm->save(ourchip);
+}
+
+/**
+ * s3c_pm_save_gpios() - Save the state of the GPIO banks.
+ *
+ * For all the GPIO banks, save the state of each one ready for going
+ * into a suspend mode.
+ */
+void s3c_pm_save_gpios(void)
+{
+ struct s3c_gpio_chip *ourchip;
+ unsigned int gpio_nr;
+
+ for (gpio_nr = 0; gpio_nr < S3C_GPIO_END; gpio_nr++) {
+ ourchip = s3c_gpiolib_getchip(gpio_nr);
+ if (!ourchip)
+ continue;
+
+ s3c_pm_save_gpio(ourchip);
+
+ S3C_PMDBG("%s: save %08x,%08x,%08x,%08x\n",
+ ourchip->chip.label,
+ ourchip->pm_save[0],
+ ourchip->pm_save[1],
+ ourchip->pm_save[2],
+ ourchip->pm_save[3]);
+
+ gpio_nr += ourchip->chip.ngpio;
+ gpio_nr += CONFIG_S3C_GPIO_SPACE;
+ }
+}
+
+/**
+ * s3c_pm_resume_gpio() - restore gpio chip data after suspend
+ * @ourchip: The suspended chip.
+ */
+static void s3c_pm_resume_gpio(struct s3c_gpio_chip *ourchip)
+{
+ struct s3c_gpio_pm *pm = ourchip->pm;
+
+ if (pm == NULL || pm->resume == NULL)
+ S3C_PMDBG("%s: no pm for %s\n", __func__, ourchip->chip.label);
+ else
+ pm->resume(ourchip);
+}
+
+void s3c_pm_restore_gpios(void)
+{
+ struct s3c_gpio_chip *ourchip;
+ unsigned int gpio_nr;
+
+ for (gpio_nr = 0; gpio_nr < S3C_GPIO_END; gpio_nr++) {
+ ourchip = s3c_gpiolib_getchip(gpio_nr);
+ if (!ourchip)
+ continue;
+
+ s3c_pm_resume_gpio(ourchip);
+
+ gpio_nr += ourchip->chip.ngpio;
+ gpio_nr += CONFIG_S3C_GPIO_SPACE;
+ }
+}
diff --git a/arch/arm/plat-s3c/pm.c b/arch/arm/plat-s3c/pm.c
index 061182c..8d97db2 100644
--- a/arch/arm/plat-s3c/pm.c
+++ b/arch/arm/plat-s3c/pm.c
@@ -21,11 +21,10 @@
#include <asm/cacheflush.h>
#include <mach/hardware.h>
+#include <mach/map.h>
#include <plat/regs-serial.h>
#include <mach/regs-clock.h>
-#include <mach/regs-gpio.h>
-#include <mach/regs-mem.h>
#include <mach/regs-irq.h>
#include <asm/irq.h>
@@ -70,6 +69,8 @@
/* Save the UART configurations if we are configured for debug. */
+unsigned char pm_uart_udivslot;
+
#ifdef CONFIG_S3C2410_PM_DEBUG
struct pm_uart_save uart_save[CONFIG_SERIAL_SAMSUNG_UARTS];
@@ -83,6 +84,12 @@
save->ufcon = __raw_readl(regs + S3C2410_UFCON);
save->umcon = __raw_readl(regs + S3C2410_UMCON);
save->ubrdiv = __raw_readl(regs + S3C2410_UBRDIV);
+
+ if (pm_uart_udivslot)
+ save->udivslot = __raw_readl(regs + S3C2443_DIVSLOT);
+
+ S3C_PMDBG("UART[%d]: ULCON=%04x, UCON=%04x, UFCON=%04x, UBRDIV=%04x\n",
+ uart, save->ulcon, save->ucon, save->ufcon, save->ubrdiv);
}
static void s3c_pm_save_uarts(void)
@@ -98,11 +105,16 @@
{
void __iomem *regs = S3C_VA_UARTx(uart);
+ s3c_pm_arch_update_uart(regs, save);
+
__raw_writel(save->ulcon, regs + S3C2410_ULCON);
__raw_writel(save->ucon, regs + S3C2410_UCON);
__raw_writel(save->ufcon, regs + S3C2410_UFCON);
__raw_writel(save->umcon, regs + S3C2410_UMCON);
__raw_writel(save->ubrdiv, regs + S3C2410_UBRDIV);
+
+ if (pm_uart_udivslot)
+ __raw_writel(save->udivslot, regs + S3C2443_DIVSLOT);
}
static void s3c_pm_restore_uarts(void)
@@ -313,6 +325,9 @@
S3C_PMDBG("%s: post sleep, preparing to return\n", __func__);
+ /* LEDs should now be 1110 */
+ s3c_pm_debug_smdkled(1 << 1, 0);
+
s3c_pm_check_restore();
/* ok, let's return from sleep */
diff --git a/arch/arm/plat-s3c24xx/Kconfig b/arch/arm/plat-s3c24xx/Kconfig
index 2c8a2f5..5b0bc91 100644
--- a/arch/arm/plat-s3c24xx/Kconfig
+++ b/arch/arm/plat-s3c24xx/Kconfig
@@ -71,6 +71,7 @@
config S3C2410_DMA
bool "S3C2410 DMA support"
depends on ARCH_S3C2410
+ select S3C_DMA
help
S3C2410 DMA support. This is needed for drivers like sound which
use the S3C2410's DMA system to move data to and from the
diff --git a/arch/arm/plat-s3c24xx/adc.c b/arch/arm/plat-s3c24xx/adc.c
index 91adfa7..ee1baf1 100644
--- a/arch/arm/plat-s3c24xx/adc.c
+++ b/arch/arm/plat-s3c24xx/adc.c
@@ -45,7 +45,8 @@
unsigned char channel;
void (*select_cb)(unsigned selected);
- void (*convert_cb)(unsigned val1, unsigned val2);
+ void (*convert_cb)(unsigned val1, unsigned val2,
+ unsigned *samples_left);
};
struct adc_device {
@@ -158,7 +159,8 @@
struct s3c_adc_client *s3c_adc_register(struct platform_device *pdev,
void (*select)(unsigned int selected),
- void (*conv)(unsigned d0, unsigned d1),
+ void (*conv)(unsigned d0, unsigned d1,
+ unsigned *samples_left),
unsigned int is_ts)
{
struct s3c_adc_client *client;
@@ -227,9 +229,10 @@
data1 = readl(adc->regs + S3C2410_ADCDAT1);
adc_dbg(adc, "read %d: 0x%04x, 0x%04x\n", client->nr_samples, data0, data1);
- (client->convert_cb)(data0 & 0x3ff, data1 & 0x3ff);
+ client->nr_samples--;
+ (client->convert_cb)(data0 & 0x3ff, data1 & 0x3ff, &client->nr_samples);
- if (--client->nr_samples > 0) {
+ if (client->nr_samples > 0) {
/* fire another conversion for this */
client->select_cb(1);
diff --git a/arch/arm/plat-s3c24xx/common-smdk.c b/arch/arm/plat-s3c24xx/common-smdk.c
index 1a8347c..aa11986 100644
--- a/arch/arm/plat-s3c24xx/common-smdk.c
+++ b/arch/arm/plat-s3c24xx/common-smdk.c
@@ -18,6 +18,7 @@
#include <linux/list.h>
#include <linux/timer.h>
#include <linux/init.h>
+#include <linux/gpio.h>
#include <linux/sysdev.h>
#include <linux/platform_device.h>
@@ -47,27 +48,27 @@
/* LED devices */
static struct s3c24xx_led_platdata smdk_pdata_led4 = {
- .gpio = S3C2410_GPF4,
+ .gpio = S3C2410_GPF(4),
.flags = S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE,
.name = "led4",
.def_trigger = "timer",
};
static struct s3c24xx_led_platdata smdk_pdata_led5 = {
- .gpio = S3C2410_GPF5,
+ .gpio = S3C2410_GPF(5),
.flags = S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE,
.name = "led5",
.def_trigger = "nand-disk",
};
static struct s3c24xx_led_platdata smdk_pdata_led6 = {
- .gpio = S3C2410_GPF6,
+ .gpio = S3C2410_GPF(6),
.flags = S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE,
.name = "led6",
};
static struct s3c24xx_led_platdata smdk_pdata_led7 = {
- .gpio = S3C2410_GPF7,
+ .gpio = S3C2410_GPF(7),
.flags = S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE,
.name = "led7",
};
@@ -184,15 +185,15 @@
{
/* Configure the LEDs (even if we have no LED support)*/
- s3c2410_gpio_cfgpin(S3C2410_GPF4, S3C2410_GPF4_OUTP);
- s3c2410_gpio_cfgpin(S3C2410_GPF5, S3C2410_GPF5_OUTP);
- s3c2410_gpio_cfgpin(S3C2410_GPF6, S3C2410_GPF6_OUTP);
- s3c2410_gpio_cfgpin(S3C2410_GPF7, S3C2410_GPF7_OUTP);
+ s3c2410_gpio_cfgpin(S3C2410_GPF(4), S3C2410_GPIO_OUTPUT);
+ s3c2410_gpio_cfgpin(S3C2410_GPF(5), S3C2410_GPIO_OUTPUT);
+ s3c2410_gpio_cfgpin(S3C2410_GPF(6), S3C2410_GPIO_OUTPUT);
+ s3c2410_gpio_cfgpin(S3C2410_GPF(7), S3C2410_GPIO_OUTPUT);
- s3c2410_gpio_setpin(S3C2410_GPF4, 1);
- s3c2410_gpio_setpin(S3C2410_GPF5, 1);
- s3c2410_gpio_setpin(S3C2410_GPF6, 1);
- s3c2410_gpio_setpin(S3C2410_GPF7, 1);
+ s3c2410_gpio_setpin(S3C2410_GPF(4), 1);
+ s3c2410_gpio_setpin(S3C2410_GPF(5), 1);
+ s3c2410_gpio_setpin(S3C2410_GPF(6), 1);
+ s3c2410_gpio_setpin(S3C2410_GPF(7), 1);
if (machine_is_smdk2443())
smdk_nand_info.twrph0 = 50;
diff --git a/arch/arm/plat-s3c24xx/devs.c b/arch/arm/plat-s3c24xx/devs.c
index 16ac01d..4eb378c 100644
--- a/arch/arm/plat-s3c24xx/devs.c
+++ b/arch/arm/plat-s3c24xx/devs.c
@@ -136,36 +136,6 @@
struct platform_device *s3c24xx_uart_devs[4] = {
};
-/* USB Host Controller */
-
-static struct resource s3c_usb_resource[] = {
- [0] = {
- .start = S3C24XX_PA_USBHOST,
- .end = S3C24XX_PA_USBHOST + S3C24XX_SZ_USBHOST - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = IRQ_USBH,
- .end = IRQ_USBH,
- .flags = IORESOURCE_IRQ,
- }
-};
-
-static u64 s3c_device_usb_dmamask = 0xffffffffUL;
-
-struct platform_device s3c_device_usb = {
- .name = "s3c2410-ohci",
- .id = -1,
- .num_resources = ARRAY_SIZE(s3c_usb_resource),
- .resource = s3c_usb_resource,
- .dev = {
- .dma_mask = &s3c_device_usb_dmamask,
- .coherent_dma_mask = 0xffffffffUL
- }
-};
-
-EXPORT_SYMBOL(s3c_device_usb);
-
/* LCD Controller */
static struct resource s3c_lcd_resource[] = {
diff --git a/arch/arm/plat-s3c24xx/dma.c b/arch/arm/plat-s3c24xx/dma.c
index 07326f6..196b191 100644
--- a/arch/arm/plat-s3c24xx/dma.c
+++ b/arch/arm/plat-s3c24xx/dma.c
@@ -31,10 +31,10 @@
#include <asm/irq.h>
#include <mach/hardware.h>
#include <mach/dma.h>
-
#include <mach/map.h>
-#include <plat/dma.h>
+#include <plat/dma-plat.h>
+#include <plat/regs-dma.h>
/* io map for dma */
static void __iomem *dma_base;
@@ -44,8 +44,6 @@
static struct s3c24xx_dma_selection dma_sel;
-/* dma channel state information */
-struct s3c2410_dma_chan s3c2410_chans[S3C2410_DMA_CHANNELS];
/* debugging functions */
@@ -135,21 +133,6 @@
#define dbg_showchan(chan) do { } while(0)
#endif /* CONFIG_S3C2410_DMA_DEBUG */
-static struct s3c2410_dma_chan *dma_chan_map[DMACH_MAX];
-
-/* lookup_dma_channel
- *
- * change the dma channel number given into a real dma channel id
-*/
-
-static struct s3c2410_dma_chan *lookup_dma_channel(unsigned int channel)
-{
- if (channel & DMACH_LOW_LEVEL)
- return &s3c2410_chans[channel & ~DMACH_LOW_LEVEL];
- else
- return dma_chan_map[channel];
-}
-
/* s3c2410_dma_stats_timeout
*
* Update DMA stats from timeout info
@@ -214,8 +197,6 @@
return 0;
}
-
-
/* s3c2410_dma_loadbuffer
*
* load a buffer, and update the channel state
@@ -453,7 +434,7 @@
int s3c2410_dma_enqueue(unsigned int channel, void *id,
dma_addr_t data, int size)
{
- struct s3c2410_dma_chan *chan = lookup_dma_channel(channel);
+ struct s3c2410_dma_chan *chan = s3c_dma_lookup_channel(channel);
struct s3c2410_dma_buf *buf;
unsigned long flags;
@@ -804,7 +785,7 @@
int s3c2410_dma_free(unsigned int channel, struct s3c2410_dma_client *client)
{
- struct s3c2410_dma_chan *chan = lookup_dma_channel(channel);
+ struct s3c2410_dma_chan *chan = s3c_dma_lookup_channel(channel);
unsigned long flags;
if (chan == NULL)
@@ -836,7 +817,7 @@
chan->irq_claimed = 0;
if (!(channel & DMACH_LOW_LEVEL))
- dma_chan_map[channel] = NULL;
+ s3c_dma_chan_map[channel] = NULL;
local_irq_restore(flags);
@@ -995,7 +976,7 @@
int
s3c2410_dma_ctrl(unsigned int channel, enum s3c2410_chan_op op)
{
- struct s3c2410_dma_chan *chan = lookup_dma_channel(channel);
+ struct s3c2410_dma_chan *chan = s3c_dma_lookup_channel(channel);
if (chan == NULL)
return -EINVAL;
@@ -1038,14 +1019,13 @@
/* s3c2410_dma_config
*
* xfersize: size of unit in bytes (1,2,4)
- * dcon: base value of the DCONx register
*/
int s3c2410_dma_config(unsigned int channel,
- int xferunit,
- int dcon)
+ int xferunit)
{
- struct s3c2410_dma_chan *chan = lookup_dma_channel(channel);
+ struct s3c2410_dma_chan *chan = s3c_dma_lookup_channel(channel);
+ unsigned int dcon;
pr_debug("%s: chan=%d, xfer_unit=%d, dcon=%08x\n",
__func__, channel, xferunit, dcon);
@@ -1055,10 +1035,33 @@
pr_debug("%s: Initial dcon is %08x\n", __func__, dcon);
- dcon |= chan->dcon & dma_sel.dcon_mask;
+ dcon = chan->dcon & dma_sel.dcon_mask;
pr_debug("%s: New dcon is %08x\n", __func__, dcon);
+ switch (chan->req_ch) {
+ case DMACH_I2S_IN:
+ case DMACH_I2S_OUT:
+ case DMACH_PCM_IN:
+ case DMACH_PCM_OUT:
+ case DMACH_MIC_IN:
+ default:
+ dcon |= S3C2410_DCON_HANDSHAKE;
+ dcon |= S3C2410_DCON_SYNC_PCLK;
+ break;
+
+ case DMACH_SDI:
+ /* note, ensure if need HANDSHAKE or not */
+ dcon |= S3C2410_DCON_SYNC_PCLK;
+ break;
+
+ case DMACH_XD0:
+ case DMACH_XD1:
+ dcon |= S3C2410_DCON_HANDSHAKE;
+ dcon |= S3C2410_DCON_SYNC_HCLK;
+ break;
+ }
+
switch (xferunit) {
case 1:
dcon |= S3C2410_DCON_BYTE;
@@ -1090,58 +1093,6 @@
EXPORT_SYMBOL(s3c2410_dma_config);
-int s3c2410_dma_setflags(unsigned int channel, unsigned int flags)
-{
- struct s3c2410_dma_chan *chan = lookup_dma_channel(channel);
-
- if (chan == NULL)
- return -EINVAL;
-
- pr_debug("%s: chan=%p, flags=%08x\n", __func__, chan, flags);
-
- chan->flags = flags;
-
- return 0;
-}
-
-EXPORT_SYMBOL(s3c2410_dma_setflags);
-
-
-/* do we need to protect the settings of the fields from
- * irq?
-*/
-
-int s3c2410_dma_set_opfn(unsigned int channel, s3c2410_dma_opfn_t rtn)
-{
- struct s3c2410_dma_chan *chan = lookup_dma_channel(channel);
-
- if (chan == NULL)
- return -EINVAL;
-
- pr_debug("%s: chan=%p, op rtn=%p\n", __func__, chan, rtn);
-
- chan->op_fn = rtn;
-
- return 0;
-}
-
-EXPORT_SYMBOL(s3c2410_dma_set_opfn);
-
-int s3c2410_dma_set_buffdone_fn(unsigned int channel, s3c2410_dma_cbfn_t rtn)
-{
- struct s3c2410_dma_chan *chan = lookup_dma_channel(channel);
-
- if (chan == NULL)
- return -EINVAL;
-
- pr_debug("%s: chan=%p, callback rtn=%p\n", __func__, chan, rtn);
-
- chan->callback_fn = rtn;
-
- return 0;
-}
-
-EXPORT_SYMBOL(s3c2410_dma_set_buffdone_fn);
/* s3c2410_dma_devconfig
*
@@ -1150,29 +1101,38 @@
* source: S3C2410_DMASRC_HW: source is hardware
* S3C2410_DMASRC_MEM: source is memory
*
- * hwcfg: the value for xxxSTCn register,
- * bit 0: 0=increment pointer, 1=leave pointer
- * bit 1: 0=source is AHB, 1=source is APB
- *
* devaddr: physical address of the source
*/
int s3c2410_dma_devconfig(int channel,
enum s3c2410_dmasrc source,
- int hwcfg,
unsigned long devaddr)
{
- struct s3c2410_dma_chan *chan = lookup_dma_channel(channel);
+ struct s3c2410_dma_chan *chan = s3c_dma_lookup_channel(channel);
+ unsigned int hwcfg;
if (chan == NULL)
return -EINVAL;
- pr_debug("%s: source=%d, hwcfg=%08x, devaddr=%08lx\n",
- __func__, (int)source, hwcfg, devaddr);
+ pr_debug("%s: source=%d, devaddr=%08lx\n",
+ __func__, (int)source, devaddr);
chan->source = source;
chan->dev_addr = devaddr;
- chan->hw_cfg = hwcfg;
+
+ switch (chan->req_ch) {
+ case DMACH_XD0:
+ case DMACH_XD1:
+ hwcfg = 0; /* AHB */
+ break;
+
+ default:
+ hwcfg = S3C2410_DISRCC_APB;
+ }
+
+ /* always assume our peripheral desintation is a fixed
+ * address in memory. */
+ hwcfg |= S3C2410_DISRCC_INC;
switch (source) {
case S3C2410_DMASRC_HW:
@@ -1219,7 +1179,7 @@
int s3c2410_dma_getposition(unsigned int channel, dma_addr_t *src, dma_addr_t *dst)
{
- struct s3c2410_dma_chan *chan = lookup_dma_channel(channel);
+ struct s3c2410_dma_chan *chan = s3c_dma_lookup_channel(channel);
if (chan == NULL)
return -EINVAL;
@@ -1278,8 +1238,8 @@
printk(KERN_INFO "dma%d: restoring configuration\n", cp->number);
- s3c2410_dma_config(no, cp->xfer_unit, cp->dcon);
- s3c2410_dma_devconfig(no, cp->source, cp->hw_cfg, cp->dev_addr);
+ s3c2410_dma_config(no, cp->xfer_unit);
+ s3c2410_dma_devconfig(no, cp->source, cp->dev_addr);
/* re-select the dma source for this channel */
@@ -1476,7 +1436,8 @@
found:
dmach = &s3c2410_chans[ch];
dmach->map = ch_map;
- dma_chan_map[channel] = dmach;
+ dmach->req_ch = channel;
+ s3c_dma_chan_map[channel] = dmach;
/* select the channel */
diff --git a/arch/arm/plat-s3c24xx/gpio.c b/arch/arm/plat-s3c24xx/gpio.c
index 4a899c2..95df059 100644
--- a/arch/arm/plat-s3c24xx/gpio.c
+++ b/arch/arm/plat-s3c24xx/gpio.c
@@ -183,35 +183,19 @@
int s3c2410_gpio_getirq(unsigned int pin)
{
- if (pin < S3C2410_GPF0 || pin > S3C2410_GPG15)
- return -1; /* not valid interrupts */
+ if (pin < S3C2410_GPF(0) || pin > S3C2410_GPG(15))
+ return -EINVAL; /* not valid interrupts */
- if (pin < S3C2410_GPG0 && pin > S3C2410_GPF7)
- return -1; /* not valid pin */
+ if (pin < S3C2410_GPG(0) && pin > S3C2410_GPF(7))
+ return -EINVAL; /* not valid pin */
- if (pin < S3C2410_GPF4)
- return (pin - S3C2410_GPF0) + IRQ_EINT0;
+ if (pin < S3C2410_GPF(4))
+ return (pin - S3C2410_GPF(0)) + IRQ_EINT0;
- if (pin < S3C2410_GPG0)
- return (pin - S3C2410_GPF4) + IRQ_EINT4;
+ if (pin < S3C2410_GPG(0))
+ return (pin - S3C2410_GPF(4)) + IRQ_EINT4;
- return (pin - S3C2410_GPG0) + IRQ_EINT8;
+ return (pin - S3C2410_GPG(0)) + IRQ_EINT8;
}
EXPORT_SYMBOL(s3c2410_gpio_getirq);
-
-int s3c2410_gpio_irq2pin(unsigned int irq)
-{
- if (irq >= IRQ_EINT0 && irq <= IRQ_EINT3)
- return S3C2410_GPF0 + (irq - IRQ_EINT0);
-
- if (irq >= IRQ_EINT4 && irq <= IRQ_EINT7)
- return S3C2410_GPF4 + (irq - IRQ_EINT4);
-
- if (irq >= IRQ_EINT8 && irq <= IRQ_EINT23)
- return S3C2410_GPG0 + (irq - IRQ_EINT8);
-
- return -EINVAL;
-}
-
-EXPORT_SYMBOL(s3c2410_gpio_irq2pin);
diff --git a/arch/arm/plat-s3c24xx/gpiolib.c b/arch/arm/plat-s3c24xx/gpiolib.c
index 5c0491b..6d7a961 100644
--- a/arch/arm/plat-s3c24xx/gpiolib.c
+++ b/arch/arm/plat-s3c24xx/gpiolib.c
@@ -15,6 +15,7 @@
#include <linux/init.h>
#include <linux/module.h>
#include <linux/interrupt.h>
+#include <linux/sysdev.h>
#include <linux/ioport.h>
#include <linux/io.h>
#include <linux/gpio.h>
@@ -22,6 +23,7 @@
#include <mach/gpio-core.h>
#include <mach/hardware.h>
#include <asm/irq.h>
+#include <plat/pm.h>
#include <mach/regs-gpio.h>
@@ -77,9 +79,10 @@
struct s3c_gpio_chip s3c24xx_gpios[] = {
[0] = {
- .base = S3C24XX_GPIO_BASE(S3C2410_GPA0),
+ .base = S3C2410_GPACON,
+ .pm = __gpio_pm(&s3c_gpio_pm_1bit),
.chip = {
- .base = S3C2410_GPA0,
+ .base = S3C2410_GPA(0),
.owner = THIS_MODULE,
.label = "GPIOA",
.ngpio = 24,
@@ -88,45 +91,50 @@
},
},
[1] = {
- .base = S3C24XX_GPIO_BASE(S3C2410_GPB0),
+ .base = S3C2410_GPBCON,
+ .pm = __gpio_pm(&s3c_gpio_pm_2bit),
.chip = {
- .base = S3C2410_GPB0,
+ .base = S3C2410_GPB(0),
.owner = THIS_MODULE,
.label = "GPIOB",
.ngpio = 16,
},
},
[2] = {
- .base = S3C24XX_GPIO_BASE(S3C2410_GPC0),
+ .base = S3C2410_GPCCON,
+ .pm = __gpio_pm(&s3c_gpio_pm_2bit),
.chip = {
- .base = S3C2410_GPC0,
+ .base = S3C2410_GPC(0),
.owner = THIS_MODULE,
.label = "GPIOC",
.ngpio = 16,
},
},
[3] = {
- .base = S3C24XX_GPIO_BASE(S3C2410_GPD0),
+ .base = S3C2410_GPDCON,
+ .pm = __gpio_pm(&s3c_gpio_pm_2bit),
.chip = {
- .base = S3C2410_GPD0,
+ .base = S3C2410_GPD(0),
.owner = THIS_MODULE,
.label = "GPIOD",
.ngpio = 16,
},
},
[4] = {
- .base = S3C24XX_GPIO_BASE(S3C2410_GPE0),
+ .base = S3C2410_GPECON,
+ .pm = __gpio_pm(&s3c_gpio_pm_2bit),
.chip = {
- .base = S3C2410_GPE0,
+ .base = S3C2410_GPE(0),
.label = "GPIOE",
.owner = THIS_MODULE,
.ngpio = 16,
},
},
[5] = {
- .base = S3C24XX_GPIO_BASE(S3C2410_GPF0),
+ .base = S3C2410_GPFCON,
+ .pm = __gpio_pm(&s3c_gpio_pm_2bit),
.chip = {
- .base = S3C2410_GPF0,
+ .base = S3C2410_GPF(0),
.owner = THIS_MODULE,
.label = "GPIOF",
.ngpio = 8,
@@ -134,14 +142,24 @@
},
},
[6] = {
- .base = S3C24XX_GPIO_BASE(S3C2410_GPG0),
+ .base = S3C2410_GPGCON,
+ .pm = __gpio_pm(&s3c_gpio_pm_2bit),
.chip = {
- .base = S3C2410_GPG0,
+ .base = S3C2410_GPG(0),
.owner = THIS_MODULE,
.label = "GPIOG",
- .ngpio = 10,
+ .ngpio = 16,
.to_irq = s3c24xx_gpiolib_bankg_toirq,
},
+ }, {
+ .base = S3C2410_GPHCON,
+ .pm = __gpio_pm(&s3c_gpio_pm_2bit),
+ .chip = {
+ .base = S3C2410_GPH(0),
+ .owner = THIS_MODULE,
+ .label = "GPIOH",
+ .ngpio = 11,
+ },
},
};
@@ -156,4 +174,4 @@
return 0;
}
-arch_initcall(s3c24xx_gpiolib_init);
+core_initcall(s3c24xx_gpiolib_init);
diff --git a/arch/arm/plat-s3c24xx/include/plat/dma.h b/arch/arm/plat-s3c24xx/include/plat/dma-plat.h
similarity index 86%
rename from arch/arm/plat-s3c24xx/include/plat/dma.h
rename to arch/arm/plat-s3c24xx/include/plat/dma-plat.h
index c78efe3..9565ead 100644
--- a/arch/arm/plat-s3c24xx/include/plat/dma.h
+++ b/arch/arm/plat-s3c24xx/include/plat/dma-plat.h
@@ -1,4 +1,4 @@
-/* linux/include/asm-arm/plat-s3c24xx/dma.h
+/* linux/arch/arm/plat-s3c24xx/include/plat/dma-plat.h
*
* Copyright (C) 2006 Simtec Electronics
* Ben Dooks <ben@simtec.co.uk>
@@ -10,8 +10,10 @@
* published by the Free Software Foundation.
*/
+#include <plat/dma-core.h>
+
extern struct sysdev_class dma_sysclass;
-extern struct s3c2410_dma_chan s3c2410_chans[S3C2410_DMA_CHANNELS];
+extern struct s3c2410_dma_chan s3c2410_chans[S3C_DMA_CHANNELS];
#define DMA_CH_VALID (1<<31)
#define DMA_CH_NEVER (1<<30)
@@ -31,8 +33,8 @@
const char *name;
struct s3c24xx_dma_addr hw_addr;
- unsigned long channels[S3C2410_DMA_CHANNELS];
- unsigned long channels_rx[S3C2410_DMA_CHANNELS];
+ unsigned long channels[S3C_DMA_CHANNELS];
+ unsigned long channels_rx[S3C_DMA_CHANNELS];
};
struct s3c24xx_dma_selection {
@@ -58,7 +60,7 @@
*/
struct s3c24xx_dma_order_ch {
- unsigned int list[S3C2410_DMA_CHANNELS]; /* list of channels */
+ unsigned int list[S3C_DMA_CHANNELS]; /* list of channels */
unsigned int flags; /* flags */
};
diff --git a/arch/arm/plat-s3c24xx/include/plat/map.h b/arch/arm/plat-s3c24xx/include/plat/map.h
index eed8f78..c4d1334 100644
--- a/arch/arm/plat-s3c24xx/include/plat/map.h
+++ b/arch/arm/plat-s3c24xx/include/plat/map.h
@@ -58,7 +58,6 @@
#define S3C24XX_SZ_SPI SZ_1M
#define S3C24XX_SZ_SDI SZ_1M
#define S3C24XX_SZ_NAND SZ_1M
-#define S3C24XX_SZ_USBHOST SZ_1M
/* GPIO ports */
diff --git a/arch/arm/plat-s3c24xx/include/plat/pm-core.h b/arch/arm/plat-s3c24xx/include/plat/pm-core.h
index c758821..fb45dd9 100644
--- a/arch/arm/plat-s3c24xx/include/plat/pm-core.h
+++ b/arch/arm/plat-s3c24xx/include/plat/pm-core.h
@@ -57,3 +57,8 @@
s3c_pm_show_resume_irqs(IRQ_EINT4-4, __raw_readl(S3C2410_EINTPEND),
s3c_irqwake_eintmask);
}
+
+static inline void s3c_pm_arch_update_uart(void __iomem *regs,
+ struct pm_uart_save *save)
+{
+}
diff --git a/arch/arm/plat-s3c24xx/include/plat/regs-dma.h b/arch/arm/plat-s3c24xx/include/plat/regs-dma.h
new file mode 100644
index 0000000..3bc0a21
--- /dev/null
+++ b/arch/arm/plat-s3c24xx/include/plat/regs-dma.h
@@ -0,0 +1,145 @@
+/* arch/arm/mach-s3c2410/include/mach/dma.h
+ *
+ * Copyright (C) 2003,2004,2006 Simtec Electronics
+ * Ben Dooks <ben@simtec.co.uk>
+ *
+ * Samsung S3C24XX DMA support
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+/* DMA Register definitions */
+
+#define S3C2410_DMA_DISRC (0x00)
+#define S3C2410_DMA_DISRCC (0x04)
+#define S3C2410_DMA_DIDST (0x08)
+#define S3C2410_DMA_DIDSTC (0x0C)
+#define S3C2410_DMA_DCON (0x10)
+#define S3C2410_DMA_DSTAT (0x14)
+#define S3C2410_DMA_DCSRC (0x18)
+#define S3C2410_DMA_DCDST (0x1C)
+#define S3C2410_DMA_DMASKTRIG (0x20)
+#define S3C2412_DMA_DMAREQSEL (0x24)
+#define S3C2443_DMA_DMAREQSEL (0x24)
+
+#define S3C2410_DISRCC_INC (1<<0)
+#define S3C2410_DISRCC_APB (1<<1)
+
+#define S3C2410_DMASKTRIG_STOP (1<<2)
+#define S3C2410_DMASKTRIG_ON (1<<1)
+#define S3C2410_DMASKTRIG_SWTRIG (1<<0)
+
+#define S3C2410_DCON_DEMAND (0<<31)
+#define S3C2410_DCON_HANDSHAKE (1<<31)
+#define S3C2410_DCON_SYNC_PCLK (0<<30)
+#define S3C2410_DCON_SYNC_HCLK (1<<30)
+
+#define S3C2410_DCON_INTREQ (1<<29)
+
+#define S3C2410_DCON_CH0_XDREQ0 (0<<24)
+#define S3C2410_DCON_CH0_UART0 (1<<24)
+#define S3C2410_DCON_CH0_SDI (2<<24)
+#define S3C2410_DCON_CH0_TIMER (3<<24)
+#define S3C2410_DCON_CH0_USBEP1 (4<<24)
+
+#define S3C2410_DCON_CH1_XDREQ1 (0<<24)
+#define S3C2410_DCON_CH1_UART1 (1<<24)
+#define S3C2410_DCON_CH1_I2SSDI (2<<24)
+#define S3C2410_DCON_CH1_SPI (3<<24)
+#define S3C2410_DCON_CH1_USBEP2 (4<<24)
+
+#define S3C2410_DCON_CH2_I2SSDO (0<<24)
+#define S3C2410_DCON_CH2_I2SSDI (1<<24)
+#define S3C2410_DCON_CH2_SDI (2<<24)
+#define S3C2410_DCON_CH2_TIMER (3<<24)
+#define S3C2410_DCON_CH2_USBEP3 (4<<24)
+
+#define S3C2410_DCON_CH3_UART2 (0<<24)
+#define S3C2410_DCON_CH3_SDI (1<<24)
+#define S3C2410_DCON_CH3_SPI (2<<24)
+#define S3C2410_DCON_CH3_TIMER (3<<24)
+#define S3C2410_DCON_CH3_USBEP4 (4<<24)
+
+#define S3C2410_DCON_SRCSHIFT (24)
+#define S3C2410_DCON_SRCMASK (7<<24)
+
+#define S3C2410_DCON_BYTE (0<<20)
+#define S3C2410_DCON_HALFWORD (1<<20)
+#define S3C2410_DCON_WORD (2<<20)
+
+#define S3C2410_DCON_AUTORELOAD (0<<22)
+#define S3C2410_DCON_NORELOAD (1<<22)
+#define S3C2410_DCON_HWTRIG (1<<23)
+
+#ifdef CONFIG_CPU_S3C2440
+#define S3C2440_DIDSTC_CHKINT (1<<2)
+
+#define S3C2440_DCON_CH0_I2SSDO (5<<24)
+#define S3C2440_DCON_CH0_PCMIN (6<<24)
+
+#define S3C2440_DCON_CH1_PCMOUT (5<<24)
+#define S3C2440_DCON_CH1_SDI (6<<24)
+
+#define S3C2440_DCON_CH2_PCMIN (5<<24)
+#define S3C2440_DCON_CH2_MICIN (6<<24)
+
+#define S3C2440_DCON_CH3_MICIN (5<<24)
+#define S3C2440_DCON_CH3_PCMOUT (6<<24)
+#endif
+
+#ifdef CONFIG_CPU_S3C2412
+
+#define S3C2412_DMAREQSEL_SRC(x) ((x)<<1)
+
+#define S3C2412_DMAREQSEL_HW (1)
+
+#define S3C2412_DMAREQSEL_SPI0TX S3C2412_DMAREQSEL_SRC(0)
+#define S3C2412_DMAREQSEL_SPI0RX S3C2412_DMAREQSEL_SRC(1)
+#define S3C2412_DMAREQSEL_SPI1TX S3C2412_DMAREQSEL_SRC(2)
+#define S3C2412_DMAREQSEL_SPI1RX S3C2412_DMAREQSEL_SRC(3)
+#define S3C2412_DMAREQSEL_I2STX S3C2412_DMAREQSEL_SRC(4)
+#define S3C2412_DMAREQSEL_I2SRX S3C2412_DMAREQSEL_SRC(5)
+#define S3C2412_DMAREQSEL_TIMER S3C2412_DMAREQSEL_SRC(9)
+#define S3C2412_DMAREQSEL_SDI S3C2412_DMAREQSEL_SRC(10)
+#define S3C2412_DMAREQSEL_USBEP1 S3C2412_DMAREQSEL_SRC(13)
+#define S3C2412_DMAREQSEL_USBEP2 S3C2412_DMAREQSEL_SRC(14)
+#define S3C2412_DMAREQSEL_USBEP3 S3C2412_DMAREQSEL_SRC(15)
+#define S3C2412_DMAREQSEL_USBEP4 S3C2412_DMAREQSEL_SRC(16)
+#define S3C2412_DMAREQSEL_XDREQ0 S3C2412_DMAREQSEL_SRC(17)
+#define S3C2412_DMAREQSEL_XDREQ1 S3C2412_DMAREQSEL_SRC(18)
+#define S3C2412_DMAREQSEL_UART0_0 S3C2412_DMAREQSEL_SRC(19)
+#define S3C2412_DMAREQSEL_UART0_1 S3C2412_DMAREQSEL_SRC(20)
+#define S3C2412_DMAREQSEL_UART1_0 S3C2412_DMAREQSEL_SRC(21)
+#define S3C2412_DMAREQSEL_UART1_1 S3C2412_DMAREQSEL_SRC(22)
+#define S3C2412_DMAREQSEL_UART2_0 S3C2412_DMAREQSEL_SRC(23)
+#define S3C2412_DMAREQSEL_UART2_1 S3C2412_DMAREQSEL_SRC(24)
+
+#endif
+
+#define S3C2443_DMAREQSEL_SRC(x) ((x)<<1)
+
+#define S3C2443_DMAREQSEL_HW (1)
+
+#define S3C2443_DMAREQSEL_SPI0TX S3C2443_DMAREQSEL_SRC(0)
+#define S3C2443_DMAREQSEL_SPI0RX S3C2443_DMAREQSEL_SRC(1)
+#define S3C2443_DMAREQSEL_SPI1TX S3C2443_DMAREQSEL_SRC(2)
+#define S3C2443_DMAREQSEL_SPI1RX S3C2443_DMAREQSEL_SRC(3)
+#define S3C2443_DMAREQSEL_I2STX S3C2443_DMAREQSEL_SRC(4)
+#define S3C2443_DMAREQSEL_I2SRX S3C2443_DMAREQSEL_SRC(5)
+#define S3C2443_DMAREQSEL_TIMER S3C2443_DMAREQSEL_SRC(9)
+#define S3C2443_DMAREQSEL_SDI S3C2443_DMAREQSEL_SRC(10)
+#define S3C2443_DMAREQSEL_XDREQ0 S3C2443_DMAREQSEL_SRC(17)
+#define S3C2443_DMAREQSEL_XDREQ1 S3C2443_DMAREQSEL_SRC(18)
+#define S3C2443_DMAREQSEL_UART0_0 S3C2443_DMAREQSEL_SRC(19)
+#define S3C2443_DMAREQSEL_UART0_1 S3C2443_DMAREQSEL_SRC(20)
+#define S3C2443_DMAREQSEL_UART1_0 S3C2443_DMAREQSEL_SRC(21)
+#define S3C2443_DMAREQSEL_UART1_1 S3C2443_DMAREQSEL_SRC(22)
+#define S3C2443_DMAREQSEL_UART2_0 S3C2443_DMAREQSEL_SRC(23)
+#define S3C2443_DMAREQSEL_UART2_1 S3C2443_DMAREQSEL_SRC(24)
+#define S3C2443_DMAREQSEL_UART3_0 S3C2443_DMAREQSEL_SRC(25)
+#define S3C2443_DMAREQSEL_UART3_1 S3C2443_DMAREQSEL_SRC(26)
+#define S3C2443_DMAREQSEL_PCMOUT S3C2443_DMAREQSEL_SRC(27)
+#define S3C2443_DMAREQSEL_PCMIN S3C2443_DMAREQSEL_SRC(28)
+#define S3C2443_DMAREQSEL_MICIN S3C2443_DMAREQSEL_SRC(29)
diff --git a/arch/arm/plat-s3c24xx/pm.c b/arch/arm/plat-s3c24xx/pm.c
index 062a293..56e5253 100644
--- a/arch/arm/plat-s3c24xx/pm.c
+++ b/arch/arm/plat-s3c24xx/pm.c
@@ -30,6 +30,7 @@
#include <linux/suspend.h>
#include <linux/errno.h>
#include <linux/time.h>
+#include <linux/gpio.h>
#include <linux/interrupt.h>
#include <linux/serial_core.h>
#include <linux/io.h>
@@ -75,43 +76,10 @@
SAVE_ITEM(S3C2410_CLKSLOW),
};
-static struct gpio_sleep {
- void __iomem *base;
- unsigned int gpcon;
- unsigned int gpdat;
- unsigned int gpup;
-} gpio_save[] = {
- [0] = {
- .base = S3C2410_GPACON,
- },
- [1] = {
- .base = S3C2410_GPBCON,
- },
- [2] = {
- .base = S3C2410_GPCCON,
- },
- [3] = {
- .base = S3C2410_GPDCON,
- },
- [4] = {
- .base = S3C2410_GPECON,
- },
- [5] = {
- .base = S3C2410_GPFCON,
- },
- [6] = {
- .base = S3C2410_GPGCON,
- },
- [7] = {
- .base = S3C2410_GPHCON,
- },
-};
-
static struct sleep_save misc_save[] = {
SAVE_ITEM(S3C2410_DCLKCON),
};
-
/* s3c_pm_check_resume_pin
*
* check to see if the pin is configured correctly for sleep mode, and
@@ -156,195 +124,15 @@
* and then configure it as an input if it is not
*/
- for (pin = S3C2410_GPF0; pin <= S3C2410_GPF7; pin++) {
- s3c_pm_check_resume_pin(pin, pin - S3C2410_GPF0);
+ for (pin = S3C2410_GPF(0); pin <= S3C2410_GPF(7); pin++) {
+ s3c_pm_check_resume_pin(pin, pin - S3C2410_GPF(0));
}
- for (pin = S3C2410_GPG0; pin <= S3C2410_GPG7; pin++) {
- s3c_pm_check_resume_pin(pin, (pin - S3C2410_GPG0)+8);
+ for (pin = S3C2410_GPG(0); pin <= S3C2410_GPG(7); pin++) {
+ s3c_pm_check_resume_pin(pin, (pin - S3C2410_GPG(0))+8);
}
}
-/* offsets for CON/DAT/UP registers */
-
-#define OFFS_CON (S3C2410_GPACON - S3C2410_GPACON)
-#define OFFS_DAT (S3C2410_GPADAT - S3C2410_GPACON)
-#define OFFS_UP (S3C2410_GPBUP - S3C2410_GPBCON)
-
-/* s3c_pm_save_gpios()
- *
- * Save the state of the GPIOs
- */
-
-void s3c_pm_save_gpios(void)
-{
- struct gpio_sleep *gps = gpio_save;
- unsigned int gpio;
-
- for (gpio = 0; gpio < ARRAY_SIZE(gpio_save); gpio++, gps++) {
- void __iomem *base = gps->base;
-
- gps->gpcon = __raw_readl(base + OFFS_CON);
- gps->gpdat = __raw_readl(base + OFFS_DAT);
-
- if (gpio > 0)
- gps->gpup = __raw_readl(base + OFFS_UP);
-
- }
-}
-
-/* Test whether the given masked+shifted bits of an GPIO configuration
- * are one of the SFN (special function) modes. */
-
-static inline int is_sfn(unsigned long con)
-{
- return (con == 2 || con == 3);
-}
-
-/* Test if the given masked+shifted GPIO configuration is an input */
-
-static inline int is_in(unsigned long con)
-{
- return con == 0;
-}
-
-/* Test if the given masked+shifted GPIO configuration is an output */
-
-static inline int is_out(unsigned long con)
-{
- return con == 1;
-}
-
-/**
- * s3c2410_pm_restore_gpio() - restore the given GPIO bank
- * @index: The number of the GPIO bank being resumed.
- * @gps: The sleep confgiuration for the bank.
- *
- * Restore one of the GPIO banks that was saved during suspend. This is
- * not as simple as once thought, due to the possibility of glitches
- * from the order that the CON and DAT registers are set in.
- *
- * The three states the pin can be are {IN,OUT,SFN} which gives us 9
- * combinations of changes to check. Three of these, if the pin stays
- * in the same configuration can be discounted. This leaves us with
- * the following:
- *
- * { IN => OUT } Change DAT first
- * { IN => SFN } Change CON first
- * { OUT => SFN } Change CON first, so new data will not glitch
- * { OUT => IN } Change CON first, so new data will not glitch
- * { SFN => IN } Change CON first
- * { SFN => OUT } Change DAT first, so new data will not glitch [1]
- *
- * We do not currently deal with the UP registers as these control
- * weak resistors, so a small delay in change should not need to bring
- * these into the calculations.
- *
- * [1] this assumes that writing to a pin DAT whilst in SFN will set the
- * state for when it is next output.
- */
-
-static void s3c2410_pm_restore_gpio(int index, struct gpio_sleep *gps)
-{
- void __iomem *base = gps->base;
- unsigned long gps_gpcon = gps->gpcon;
- unsigned long gps_gpdat = gps->gpdat;
- unsigned long old_gpcon;
- unsigned long old_gpdat;
- unsigned long old_gpup = 0x0;
- unsigned long gpcon;
- int nr;
-
- old_gpcon = __raw_readl(base + OFFS_CON);
- old_gpdat = __raw_readl(base + OFFS_DAT);
-
- if (base == S3C2410_GPACON) {
- /* GPACON only has one bit per control / data and no PULLUPs.
- * GPACON[x] = 0 => Output, 1 => SFN */
-
- /* first set all SFN bits to SFN */
-
- gpcon = old_gpcon | gps->gpcon;
- __raw_writel(gpcon, base + OFFS_CON);
-
- /* now set all the other bits */
-
- __raw_writel(gps_gpdat, base + OFFS_DAT);
- __raw_writel(gps_gpcon, base + OFFS_CON);
- } else {
- unsigned long old, new, mask;
- unsigned long change_mask = 0x0;
-
- old_gpup = __raw_readl(base + OFFS_UP);
-
- /* Create a change_mask of all the items that need to have
- * their CON value changed before their DAT value, so that
- * we minimise the work between the two settings.
- */
-
- for (nr = 0, mask = 0x03; nr < 32; nr += 2, mask <<= 2) {
- old = (old_gpcon & mask) >> nr;
- new = (gps_gpcon & mask) >> nr;
-
- /* If there is no change, then skip */
-
- if (old == new)
- continue;
-
- /* If both are special function, then skip */
-
- if (is_sfn(old) && is_sfn(new))
- continue;
-
- /* Change is IN => OUT, do not change now */
-
- if (is_in(old) && is_out(new))
- continue;
-
- /* Change is SFN => OUT, do not change now */
-
- if (is_sfn(old) && is_out(new))
- continue;
-
- /* We should now be at the case of IN=>SFN,
- * OUT=>SFN, OUT=>IN, SFN=>IN. */
-
- change_mask |= mask;
- }
-
- /* Write the new CON settings */
-
- gpcon = old_gpcon & ~change_mask;
- gpcon |= gps_gpcon & change_mask;
-
- __raw_writel(gpcon, base + OFFS_CON);
-
- /* Now change any items that require DAT,CON */
-
- __raw_writel(gps_gpdat, base + OFFS_DAT);
- __raw_writel(gps_gpcon, base + OFFS_CON);
- __raw_writel(gps->gpup, base + OFFS_UP);
- }
-
- S3C_PMDBG("GPIO[%d] CON %08lx => %08lx, DAT %08lx => %08lx\n",
- index, old_gpcon, gps_gpcon, old_gpdat, gps_gpdat);
-}
-
-
-/** s3c2410_pm_restore_gpios()
- *
- * Restore the state of the GPIOs
- */
-
-void s3c_pm_restore_gpios(void)
-{
- struct gpio_sleep *gps = gpio_save;
- int gpio;
-
- for (gpio = 0; gpio < ARRAY_SIZE(gpio_save); gpio++, gps++) {
- s3c2410_pm_restore_gpio(gpio, gps);
- }
-}
void s3c_pm_restore_core(void)
{
diff --git a/arch/arm/plat-s3c24xx/setup-i2c.c b/arch/arm/plat-s3c24xx/setup-i2c.c
index d62b7e7..71a6acc 100644
--- a/arch/arm/plat-s3c24xx/setup-i2c.c
+++ b/arch/arm/plat-s3c24xx/setup-i2c.c
@@ -11,6 +11,7 @@
*/
#include <linux/kernel.h>
+#include <linux/gpio.h>
struct platform_device;
@@ -20,6 +21,6 @@
void s3c_i2c0_cfg_gpio(struct platform_device *dev)
{
- s3c2410_gpio_cfgpin(S3C2410_GPE15, S3C2410_GPE15_IICSDA);
- s3c2410_gpio_cfgpin(S3C2410_GPE14, S3C2410_GPE14_IICSCL);
+ s3c2410_gpio_cfgpin(S3C2410_GPE(15), S3C2410_GPE15_IICSDA);
+ s3c2410_gpio_cfgpin(S3C2410_GPE(14), S3C2410_GPE14_IICSCL);
}
diff --git a/arch/arm/plat-s3c24xx/spi-bus0-gpe11_12_13.c b/arch/arm/plat-s3c24xx/spi-bus0-gpe11_12_13.c
index 8b403cb..9edf789 100644
--- a/arch/arm/plat-s3c24xx/spi-bus0-gpe11_12_13.c
+++ b/arch/arm/plat-s3c24xx/spi-bus0-gpe11_12_13.c
@@ -22,16 +22,16 @@
int enable)
{
if (enable) {
- s3c2410_gpio_cfgpin(S3C2410_GPE13, S3C2410_GPE13_SPICLK0);
- s3c2410_gpio_cfgpin(S3C2410_GPE12, S3C2410_GPE12_SPIMOSI0);
- s3c2410_gpio_cfgpin(S3C2410_GPE11, S3C2410_GPE11_SPIMISO0);
- s3c2410_gpio_pullup(S3C2410_GPE11, 0);
- s3c2410_gpio_pullup(S3C2410_GPE13, 0);
+ s3c2410_gpio_cfgpin(S3C2410_GPE(13), S3C2410_GPE13_SPICLK0);
+ s3c2410_gpio_cfgpin(S3C2410_GPE(12), S3C2410_GPE12_SPIMOSI0);
+ s3c2410_gpio_cfgpin(S3C2410_GPE(11), S3C2410_GPE11_SPIMISO0);
+ s3c2410_gpio_pullup(S3C2410_GPE(11), 0);
+ s3c2410_gpio_pullup(S3C2410_GPE(13), 0);
} else {
- s3c2410_gpio_cfgpin(S3C2410_GPE13, S3C2410_GPIO_INPUT);
- s3c2410_gpio_cfgpin(S3C2410_GPE11, S3C2410_GPIO_INPUT);
- s3c2410_gpio_pullup(S3C2410_GPE11, 1);
- s3c2410_gpio_pullup(S3C2410_GPE12, 1);
- s3c2410_gpio_pullup(S3C2410_GPE13, 1);
+ s3c2410_gpio_cfgpin(S3C2410_GPE(13), S3C2410_GPIO_INPUT);
+ s3c2410_gpio_cfgpin(S3C2410_GPE(11), S3C2410_GPIO_INPUT);
+ s3c2410_gpio_pullup(S3C2410_GPE(11), 1);
+ s3c2410_gpio_pullup(S3C2410_GPE(12), 1);
+ s3c2410_gpio_pullup(S3C2410_GPE(13), 1);
}
}
diff --git a/arch/arm/plat-s3c24xx/spi-bus1-gpg5_6_7.c b/arch/arm/plat-s3c24xx/spi-bus1-gpg5_6_7.c
index 8fccd4e..f34d0fc 100644
--- a/arch/arm/plat-s3c24xx/spi-bus1-gpg5_6_7.c
+++ b/arch/arm/plat-s3c24xx/spi-bus1-gpg5_6_7.c
@@ -22,16 +22,16 @@
int enable)
{
if (enable) {
- s3c2410_gpio_cfgpin(S3C2410_GPG7, S3C2410_GPG7_SPICLK1);
- s3c2410_gpio_cfgpin(S3C2410_GPG6, S3C2410_GPG6_SPIMOSI1);
- s3c2410_gpio_cfgpin(S3C2410_GPG5, S3C2410_GPG5_SPIMISO1);
- s3c2410_gpio_pullup(S3C2410_GPG5, 0);
- s3c2410_gpio_pullup(S3C2410_GPG6, 0);
+ s3c2410_gpio_cfgpin(S3C2410_GPG(7), S3C2410_GPG7_SPICLK1);
+ s3c2410_gpio_cfgpin(S3C2410_GPG(6), S3C2410_GPG6_SPIMOSI1);
+ s3c2410_gpio_cfgpin(S3C2410_GPG(5), S3C2410_GPG5_SPIMISO1);
+ s3c2410_gpio_pullup(S3C2410_GPG(5), 0);
+ s3c2410_gpio_pullup(S3C2410_GPG(6), 0);
} else {
- s3c2410_gpio_cfgpin(S3C2410_GPG7, S3C2410_GPIO_INPUT);
- s3c2410_gpio_cfgpin(S3C2410_GPG5, S3C2410_GPIO_INPUT);
- s3c2410_gpio_pullup(S3C2410_GPG5, 1);
- s3c2410_gpio_pullup(S3C2410_GPG6, 1);
- s3c2410_gpio_pullup(S3C2410_GPG7, 1);
+ s3c2410_gpio_cfgpin(S3C2410_GPG(7), S3C2410_GPIO_INPUT);
+ s3c2410_gpio_cfgpin(S3C2410_GPG(5), S3C2410_GPIO_INPUT);
+ s3c2410_gpio_pullup(S3C2410_GPG(5), 1);
+ s3c2410_gpio_pullup(S3C2410_GPG(6), 1);
+ s3c2410_gpio_pullup(S3C2410_GPG(7), 1);
}
}
diff --git a/arch/arm/plat-s3c64xx/Kconfig b/arch/arm/plat-s3c64xx/Kconfig
index 54375a0..5ebd8b4 100644
--- a/arch/arm/plat-s3c64xx/Kconfig
+++ b/arch/arm/plat-s3c64xx/Kconfig
@@ -19,6 +19,7 @@
select S3C_GPIO_PULL_UPDOWN
select S3C_GPIO_CFG_S3C24XX
select S3C_GPIO_CFG_S3C64XX
+ select USB_ARCH_HAS_OHCI
help
Base platform code for any Samsung S3C64XX device
@@ -38,6 +39,10 @@
Common clock support code for the S3C6400 that is shared
by other CPUs in the series, such as the S3C6410.
+config S3C64XX_DMA
+ bool "S3C64XX DMA"
+ select S3C_DMA
+
# platform specific device setup
config S3C64XX_SETUP_I2C0
@@ -59,4 +64,9 @@
help
Common setup code for S3C64XX with an 24bpp RGB display helper.
+config S3C64XX_SETUP_SDHCI_GPIO
+ bool
+ help
+ Common setup code for S3C64XX SDHCI GPIO configurations
+
endif
diff --git a/arch/arm/plat-s3c64xx/Makefile b/arch/arm/plat-s3c64xx/Makefile
index 2e6d79b..2ed5df3 100644
--- a/arch/arm/plat-s3c64xx/Makefile
+++ b/arch/arm/plat-s3c64xx/Makefile
@@ -24,8 +24,19 @@
obj-$(CONFIG_CPU_S3C6400_INIT) += s3c6400-init.o
obj-$(CONFIG_CPU_S3C6400_CLOCK) += s3c6400-clock.o
+# PM support
+
+obj-$(CONFIG_PM) += pm.o
+obj-$(CONFIG_PM) += sleep.o
+obj-$(CONFIG_PM) += irq-pm.o
+
+# DMA support
+
+obj-$(CONFIG_S3C64XX_DMA) += dma.o
+
# Device setup
obj-$(CONFIG_S3C64XX_SETUP_I2C0) += setup-i2c0.o
obj-$(CONFIG_S3C64XX_SETUP_I2C1) += setup-i2c1.o
obj-$(CONFIG_S3C64XX_SETUP_FB_24BPP) += setup-fb-24bpp.o
+obj-$(CONFIG_S3C64XX_SETUP_SDHCI_GPIO) += setup-sdhci-gpio.o
\ No newline at end of file
diff --git a/arch/arm/plat-s3c64xx/clock.c b/arch/arm/plat-s3c64xx/clock.c
index ad1b968..0bc2fa1 100644
--- a/arch/arm/plat-s3c64xx/clock.c
+++ b/arch/arm/plat-s3c64xx/clock.c
@@ -27,6 +27,12 @@
#include <plat/devs.h>
#include <plat/clock.h>
+struct clk clk_h2 = {
+ .name = "hclk2",
+ .id = -1,
+ .rate = 0,
+};
+
struct clk clk_27m = {
.name = "clk_27m",
.id = -1,
@@ -152,6 +158,18 @@
.parent = &clk_48m,
.enable = s3c64xx_sclk_ctrl,
.ctrlbit = S3C_CLKCON_SCLK_MMC2_48,
+ }, {
+ .name = "dma0",
+ .id = -1,
+ .parent = &clk_h,
+ .enable = s3c64xx_hclk_ctrl,
+ .ctrlbit = S3C_CLKCON_HCLK_DMA0,
+ }, {
+ .name = "dma1",
+ .id = -1,
+ .parent = &clk_h,
+ .enable = s3c64xx_hclk_ctrl,
+ .ctrlbit = S3C_CLKCON_HCLK_DMA1,
},
};
@@ -246,6 +264,7 @@
&clk_epll,
&clk_27m,
&clk_48m,
+ &clk_h2,
};
void __init s3c64xx_register_clocks(void)
diff --git a/arch/arm/plat-s3c64xx/cpu.c b/arch/arm/plat-s3c64xx/cpu.c
index 91f49a3..b1fdd83 100644
--- a/arch/arm/plat-s3c64xx/cpu.c
+++ b/arch/arm/plat-s3c64xx/cpu.c
@@ -16,6 +16,7 @@
#include <linux/module.h>
#include <linux/interrupt.h>
#include <linux/ioport.h>
+#include <linux/sysdev.h>
#include <linux/serial_core.h>
#include <linux/platform_device.h>
#include <linux/io.h>
@@ -101,9 +102,24 @@
.pfn = __phys_to_pfn(S3C64XX_PA_MODEM),
.length = SZ_4K,
.type = MT_DEVICE,
+ }, {
+ .virtual = (unsigned long)S3C_VA_WATCHDOG,
+ .pfn = __phys_to_pfn(S3C64XX_PA_WATCHDOG),
+ .length = SZ_4K,
+ .type = MT_DEVICE,
},
};
+
+struct sysdev_class s3c64xx_sysclass = {
+ .name = "s3c64xx-core",
+};
+
+static struct sys_device s3c64xx_sysdev = {
+ .cls = &s3c64xx_sysclass,
+};
+
+
/* read cpu identification code */
void __init s3c64xx_init_io(struct map_desc *mach_desc, int size)
@@ -115,5 +131,21 @@
iotable_init(mach_desc, size);
idcode = __raw_readl(S3C_VA_SYS + 0x118);
+ if (!idcode) {
+ /* S3C6400 has the ID register in a different place,
+ * and needs a write before it can be read. */
+
+ __raw_writel(0x0, S3C_VA_SYS + 0xA1C);
+ idcode = __raw_readl(S3C_VA_SYS + 0xA1C);
+ }
+
s3c_init_cpu(idcode, cpu_ids, ARRAY_SIZE(cpu_ids));
}
+
+static __init int s3c64xx_sysdev_init(void)
+{
+ sysdev_class_register(&s3c64xx_sysclass);
+ return sysdev_register(&s3c64xx_sysdev);
+}
+
+core_initcall(s3c64xx_sysdev_init);
diff --git a/arch/arm/plat-s3c64xx/dma.c b/arch/arm/plat-s3c64xx/dma.c
new file mode 100644
index 0000000..67aa93d
--- /dev/null
+++ b/arch/arm/plat-s3c64xx/dma.c
@@ -0,0 +1,722 @@
+/* linux/arch/arm/plat-s3c64xx/dma.c
+ *
+ * Copyright 2009 Openmoko, Inc.
+ * Copyright 2009 Simtec Electronics
+ * Ben Dooks <ben@simtec.co.uk>
+ * http://armlinux.simtec.co.uk/
+ *
+ * S3C64XX DMA core
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/interrupt.h>
+#include <linux/dmapool.h>
+#include <linux/sysdev.h>
+#include <linux/errno.h>
+#include <linux/delay.h>
+#include <linux/clk.h>
+#include <linux/err.h>
+#include <linux/io.h>
+
+#include <mach/dma.h>
+#include <mach/map.h>
+#include <mach/irqs.h>
+
+#include <plat/dma-plat.h>
+#include <plat/regs-sys.h>
+
+#include <asm/hardware/pl080.h>
+
+/* dma channel state information */
+
+struct s3c64xx_dmac {
+ struct sys_device sysdev;
+ struct clk *clk;
+ void __iomem *regs;
+ struct s3c2410_dma_chan *channels;
+ enum dma_ch chanbase;
+};
+
+/* pool to provide LLI buffers */
+static struct dma_pool *dma_pool;
+
+/* Debug configuration and code */
+
+static unsigned char debug_show_buffs = 0;
+
+static void dbg_showchan(struct s3c2410_dma_chan *chan)
+{
+ pr_debug("DMA%d: %08x->%08x L %08x C %08x,%08x S %08x\n",
+ chan->number,
+ readl(chan->regs + PL080_CH_SRC_ADDR),
+ readl(chan->regs + PL080_CH_DST_ADDR),
+ readl(chan->regs + PL080_CH_LLI),
+ readl(chan->regs + PL080_CH_CONTROL),
+ readl(chan->regs + PL080S_CH_CONTROL2),
+ readl(chan->regs + PL080S_CH_CONFIG));
+}
+
+static void show_lli(struct pl080s_lli *lli)
+{
+ pr_debug("LLI[%p] %08x->%08x, NL %08x C %08x,%08x\n",
+ lli, lli->src_addr, lli->dst_addr, lli->next_lli,
+ lli->control0, lli->control1);
+}
+
+static void dbg_showbuffs(struct s3c2410_dma_chan *chan)
+{
+ struct s3c64xx_dma_buff *ptr;
+ struct s3c64xx_dma_buff *end;
+
+ pr_debug("DMA%d: buffs next %p, curr %p, end %p\n",
+ chan->number, chan->next, chan->curr, chan->end);
+
+ ptr = chan->next;
+ end = chan->end;
+
+ if (debug_show_buffs) {
+ for (; ptr != NULL; ptr = ptr->next) {
+ pr_debug("DMA%d: %08x ",
+ chan->number, ptr->lli_dma);
+ show_lli(ptr->lli);
+ }
+ }
+}
+
+/* End of Debug */
+
+static struct s3c2410_dma_chan *s3c64xx_dma_map_channel(unsigned int channel)
+{
+ struct s3c2410_dma_chan *chan;
+ unsigned int start, offs;
+
+ start = 0;
+
+ if (channel >= DMACH_PCM1_TX)
+ start = 8;
+
+ for (offs = 0; offs < 8; offs++) {
+ chan = &s3c2410_chans[start + offs];
+ if (!chan->in_use)
+ goto found;
+ }
+
+ return NULL;
+
+found:
+ s3c_dma_chan_map[channel] = chan;
+ return chan;
+}
+
+int s3c2410_dma_config(unsigned int channel, int xferunit)
+{
+ struct s3c2410_dma_chan *chan = s3c_dma_lookup_channel(channel);
+
+ if (chan == NULL)
+ return -EINVAL;
+
+ switch (xferunit) {
+ case 1:
+ chan->hw_width = 0;
+ break;
+ case 2:
+ chan->hw_width = 1;
+ break;
+ case 4:
+ chan->hw_width = 2;
+ break;
+ default:
+ printk(KERN_ERR "%s: illegal width %d\n", __func__, xferunit);
+ return -EINVAL;
+ }
+
+ return 0;
+}
+EXPORT_SYMBOL(s3c2410_dma_config);
+
+static void s3c64xx_dma_fill_lli(struct s3c2410_dma_chan *chan,
+ struct pl080s_lli *lli,
+ dma_addr_t data, int size)
+{
+ dma_addr_t src, dst;
+ u32 control0, control1;
+
+ switch (chan->source) {
+ case S3C2410_DMASRC_HW:
+ src = chan->dev_addr;
+ dst = data;
+ control0 = PL080_CONTROL_SRC_AHB2;
+ control0 |= (u32)chan->hw_width << PL080_CONTROL_SWIDTH_SHIFT;
+ control0 |= 2 << PL080_CONTROL_DWIDTH_SHIFT;
+ control0 |= PL080_CONTROL_DST_INCR;
+ break;
+
+ case S3C2410_DMASRC_MEM:
+ src = data;
+ dst = chan->dev_addr;
+ control0 = PL080_CONTROL_DST_AHB2;
+ control0 |= (u32)chan->hw_width << PL080_CONTROL_DWIDTH_SHIFT;
+ control0 |= 2 << PL080_CONTROL_SWIDTH_SHIFT;
+ control0 |= PL080_CONTROL_SRC_INCR;
+ break;
+ default:
+ BUG();
+ }
+
+ /* note, we do not currently setup any of the burst controls */
+
+ control1 = size >> chan->hw_width; /* size in no of xfers */
+ control0 |= PL080_CONTROL_PROT_SYS; /* always in priv. mode */
+ control0 |= PL080_CONTROL_TC_IRQ_EN; /* always fire IRQ */
+
+ lli->src_addr = src;
+ lli->dst_addr = dst;
+ lli->next_lli = 0;
+ lli->control0 = control0;
+ lli->control1 = control1;
+}
+
+static void s3c64xx_lli_to_regs(struct s3c2410_dma_chan *chan,
+ struct pl080s_lli *lli)
+{
+ void __iomem *regs = chan->regs;
+
+ pr_debug("%s: LLI %p => regs\n", __func__, lli);
+ show_lli(lli);
+
+ writel(lli->src_addr, regs + PL080_CH_SRC_ADDR);
+ writel(lli->dst_addr, regs + PL080_CH_DST_ADDR);
+ writel(lli->next_lli, regs + PL080_CH_LLI);
+ writel(lli->control0, regs + PL080_CH_CONTROL);
+ writel(lli->control1, regs + PL080S_CH_CONTROL2);
+}
+
+static int s3c64xx_dma_start(struct s3c2410_dma_chan *chan)
+{
+ struct s3c64xx_dmac *dmac = chan->dmac;
+ u32 config;
+ u32 bit = chan->bit;
+
+ dbg_showchan(chan);
+
+ pr_debug("%s: clearing interrupts\n", __func__);
+
+ /* clear interrupts */
+ writel(bit, dmac->regs + PL080_TC_CLEAR);
+ writel(bit, dmac->regs + PL080_ERR_CLEAR);
+
+ pr_debug("%s: starting channel\n", __func__);
+
+ config = readl(chan->regs + PL080S_CH_CONFIG);
+ config |= PL080_CONFIG_ENABLE;
+
+ pr_debug("%s: writing config %08x\n", __func__, config);
+ writel(config, chan->regs + PL080S_CH_CONFIG);
+
+ return 0;
+}
+
+static int s3c64xx_dma_stop(struct s3c2410_dma_chan *chan)
+{
+ u32 config;
+ int timeout;
+
+ pr_debug("%s: stopping channel\n", __func__);
+
+ dbg_showchan(chan);
+
+ config = readl(chan->regs + PL080S_CH_CONFIG);
+ config |= PL080_CONFIG_HALT;
+ writel(config, chan->regs + PL080S_CH_CONFIG);
+
+ timeout = 1000;
+ do {
+ config = readl(chan->regs + PL080S_CH_CONFIG);
+ pr_debug("%s: %d - config %08x\n", __func__, timeout, config);
+ if (config & PL080_CONFIG_ACTIVE)
+ udelay(10);
+ else
+ break;
+ } while (--timeout > 0);
+
+ if (config & PL080_CONFIG_ACTIVE) {
+ printk(KERN_ERR "%s: channel still active\n", __func__);
+ return -EFAULT;
+ }
+
+ config = readl(chan->regs + PL080S_CH_CONFIG);
+ config &= ~PL080_CONFIG_ENABLE;
+ writel(config, chan->regs + PL080S_CH_CONFIG);
+
+ return 0;
+}
+
+static inline void s3c64xx_dma_bufffdone(struct s3c2410_dma_chan *chan,
+ struct s3c64xx_dma_buff *buf,
+ enum s3c2410_dma_buffresult result)
+{
+ if (chan->callback_fn != NULL)
+ (chan->callback_fn)(chan, buf->pw, 0, result);
+}
+
+static void s3c64xx_dma_freebuff(struct s3c64xx_dma_buff *buff)
+{
+ dma_pool_free(dma_pool, buff->lli, buff->lli_dma);
+ kfree(buff);
+}
+
+static int s3c64xx_dma_flush(struct s3c2410_dma_chan *chan)
+{
+ struct s3c64xx_dma_buff *buff, *next;
+ u32 config;
+
+ dbg_showchan(chan);
+
+ pr_debug("%s: flushing channel\n", __func__);
+
+ config = readl(chan->regs + PL080S_CH_CONFIG);
+ config &= ~PL080_CONFIG_ENABLE;
+ writel(config, chan->regs + PL080S_CH_CONFIG);
+
+ /* dump all the buffers associated with this channel */
+
+ for (buff = chan->curr; buff != NULL; buff = next) {
+ next = buff->next;
+ pr_debug("%s: buff %p (next %p)\n", __func__, buff, buff->next);
+
+ s3c64xx_dma_bufffdone(chan, buff, S3C2410_RES_ABORT);
+ s3c64xx_dma_freebuff(buff);
+ }
+
+ chan->curr = chan->next = chan->end = NULL;
+
+ return 0;
+}
+
+int s3c2410_dma_ctrl(unsigned int channel, enum s3c2410_chan_op op)
+{
+ struct s3c2410_dma_chan *chan = s3c_dma_lookup_channel(channel);
+
+ WARN_ON(!chan);
+ if (!chan)
+ return -EINVAL;
+
+ switch (op) {
+ case S3C2410_DMAOP_START:
+ return s3c64xx_dma_start(chan);
+
+ case S3C2410_DMAOP_STOP:
+ return s3c64xx_dma_stop(chan);
+
+ case S3C2410_DMAOP_FLUSH:
+ return s3c64xx_dma_flush(chan);
+
+ /* belive PAUSE/RESUME are no-ops */
+ case S3C2410_DMAOP_PAUSE:
+ case S3C2410_DMAOP_RESUME:
+ case S3C2410_DMAOP_STARTED:
+ case S3C2410_DMAOP_TIMEOUT:
+ return 0;
+ }
+
+ return -ENOENT;
+}
+EXPORT_SYMBOL(s3c2410_dma_ctrl);
+
+/* s3c2410_dma_enque
+ *
+ */
+
+int s3c2410_dma_enqueue(unsigned int channel, void *id,
+ dma_addr_t data, int size)
+{
+ struct s3c2410_dma_chan *chan = s3c_dma_lookup_channel(channel);
+ struct s3c64xx_dma_buff *next;
+ struct s3c64xx_dma_buff *buff;
+ struct pl080s_lli *lli;
+ int ret;
+
+ WARN_ON(!chan);
+ if (!chan)
+ return -EINVAL;
+
+ buff = kzalloc(sizeof(struct s3c64xx_dma_buff), GFP_KERNEL);
+ if (!buff) {
+ printk(KERN_ERR "%s: no memory for buffer\n", __func__);
+ return -ENOMEM;
+ }
+
+ lli = dma_pool_alloc(dma_pool, GFP_KERNEL, &buff->lli_dma);
+ if (!lli) {
+ printk(KERN_ERR "%s: no memory for lli\n", __func__);
+ ret = -ENOMEM;
+ goto err_buff;
+ }
+
+ pr_debug("%s: buff %p, dp %08x lli (%p, %08x) %d\n",
+ __func__, buff, data, lli, (u32)buff->lli_dma, size);
+
+ buff->lli = lli;
+ buff->pw = id;
+
+ s3c64xx_dma_fill_lli(chan, lli, data, size);
+
+ if ((next = chan->next) != NULL) {
+ struct s3c64xx_dma_buff *end = chan->end;
+ struct pl080s_lli *endlli = end->lli;
+
+ pr_debug("enquing onto channel\n");
+
+ end->next = buff;
+ endlli->next_lli = buff->lli_dma;
+
+ if (chan->flags & S3C2410_DMAF_CIRCULAR) {
+ struct s3c64xx_dma_buff *curr = chan->curr;
+ lli->next_lli = curr->lli_dma;
+ }
+
+ if (next == chan->curr) {
+ writel(buff->lli_dma, chan->regs + PL080_CH_LLI);
+ chan->next = buff;
+ }
+
+ show_lli(endlli);
+ chan->end = buff;
+ } else {
+ pr_debug("enquing onto empty channel\n");
+
+ chan->curr = buff;
+ chan->next = buff;
+ chan->end = buff;
+
+ s3c64xx_lli_to_regs(chan, lli);
+ }
+
+ show_lli(lli);
+
+ dbg_showchan(chan);
+ dbg_showbuffs(chan);
+ return 0;
+
+err_buff:
+ kfree(buff);
+ return ret;
+}
+
+EXPORT_SYMBOL(s3c2410_dma_enqueue);
+
+
+int s3c2410_dma_devconfig(int channel,
+ enum s3c2410_dmasrc source,
+ unsigned long devaddr)
+{
+ struct s3c2410_dma_chan *chan = s3c_dma_lookup_channel(channel);
+ u32 peripheral;
+ u32 config = 0;
+
+ pr_debug("%s: channel %d, source %d, dev %08lx, chan %p\n",
+ __func__, channel, source, devaddr, chan);
+
+ WARN_ON(!chan);
+ if (!chan)
+ return -EINVAL;
+
+ peripheral = (chan->peripheral & 0xf);
+ chan->source = source;
+ chan->dev_addr = devaddr;
+
+ pr_debug("%s: peripheral %d\n", __func__, peripheral);
+
+ switch (source) {
+ case S3C2410_DMASRC_HW:
+ config = 2 << PL080_CONFIG_FLOW_CONTROL_SHIFT;
+ config |= peripheral << PL080_CONFIG_SRC_SEL_SHIFT;
+ break;
+ case S3C2410_DMASRC_MEM:
+ config = 1 << PL080_CONFIG_FLOW_CONTROL_SHIFT;
+ config |= peripheral << PL080_CONFIG_DST_SEL_SHIFT;
+ break;
+ default:
+ printk(KERN_ERR "%s: bad source\n", __func__);
+ return -EINVAL;
+ }
+
+ /* allow TC and ERR interrupts */
+ config |= PL080_CONFIG_TC_IRQ_MASK;
+ config |= PL080_CONFIG_ERR_IRQ_MASK;
+
+ pr_debug("%s: config %08x\n", __func__, config);
+
+ writel(config, chan->regs + PL080S_CH_CONFIG);
+
+ return 0;
+}
+EXPORT_SYMBOL(s3c2410_dma_devconfig);
+
+
+int s3c2410_dma_getposition(unsigned int channel,
+ dma_addr_t *src, dma_addr_t *dst)
+{
+ struct s3c2410_dma_chan *chan = s3c_dma_lookup_channel(channel);
+
+ WARN_ON(!chan);
+ if (!chan)
+ return -EINVAL;
+
+ if (src != NULL)
+ *src = readl(chan->regs + PL080_CH_SRC_ADDR);
+
+ if (dst != NULL)
+ *dst = readl(chan->regs + PL080_CH_DST_ADDR);
+
+ return 0;
+}
+EXPORT_SYMBOL(s3c2410_dma_getposition);
+
+/* s3c2410_request_dma
+ *
+ * get control of an dma channel
+*/
+
+int s3c2410_dma_request(unsigned int channel,
+ struct s3c2410_dma_client *client,
+ void *dev)
+{
+ struct s3c2410_dma_chan *chan;
+ unsigned long flags;
+
+ pr_debug("dma%d: s3c2410_request_dma: client=%s, dev=%p\n",
+ channel, client->name, dev);
+
+ local_irq_save(flags);
+
+ chan = s3c64xx_dma_map_channel(channel);
+ if (chan == NULL) {
+ local_irq_restore(flags);
+ return -EBUSY;
+ }
+
+ dbg_showchan(chan);
+
+ chan->client = client;
+ chan->in_use = 1;
+ chan->peripheral = channel;
+
+ local_irq_restore(flags);
+
+ /* need to setup */
+
+ pr_debug("%s: channel initialised, %p\n", __func__, chan);
+
+ return chan->number | DMACH_LOW_LEVEL;
+}
+
+EXPORT_SYMBOL(s3c2410_dma_request);
+
+/* s3c2410_dma_free
+ *
+ * release the given channel back to the system, will stop and flush
+ * any outstanding transfers, and ensure the channel is ready for the
+ * next claimant.
+ *
+ * Note, although a warning is currently printed if the freeing client
+ * info is not the same as the registrant's client info, the free is still
+ * allowed to go through.
+*/
+
+int s3c2410_dma_free(unsigned int channel, struct s3c2410_dma_client *client)
+{
+ struct s3c2410_dma_chan *chan = s3c_dma_lookup_channel(channel);
+ unsigned long flags;
+
+ if (chan == NULL)
+ return -EINVAL;
+
+ local_irq_save(flags);
+
+ if (chan->client != client) {
+ printk(KERN_WARNING "dma%d: possible free from different client (channel %p, passed %p)\n",
+ channel, chan->client, client);
+ }
+
+ /* sort out stopping and freeing the channel */
+
+
+ chan->client = NULL;
+ chan->in_use = 0;
+
+ if (!(channel & DMACH_LOW_LEVEL))
+ s3c_dma_chan_map[channel] = NULL;
+
+ local_irq_restore(flags);
+
+ return 0;
+}
+
+EXPORT_SYMBOL(s3c2410_dma_free);
+
+
+static void s3c64xx_dma_tcirq(struct s3c64xx_dmac *dmac, int offs)
+{
+ struct s3c2410_dma_chan *chan = dmac->channels + offs;
+
+ /* note, we currently do not bother to work out which buffer
+ * or buffers have been completed since the last tc-irq. */
+
+ if (chan->callback_fn)
+ (chan->callback_fn)(chan, chan->curr->pw, 0, S3C2410_RES_OK);
+}
+
+static void s3c64xx_dma_errirq(struct s3c64xx_dmac *dmac, int offs)
+{
+ printk(KERN_DEBUG "%s: offs %d\n", __func__, offs);
+}
+
+static irqreturn_t s3c64xx_dma_irq(int irq, void *pw)
+{
+ struct s3c64xx_dmac *dmac = pw;
+ u32 tcstat, errstat;
+ u32 bit;
+ int offs;
+
+ tcstat = readl(dmac->regs + PL080_TC_STATUS);
+ errstat = readl(dmac->regs + PL080_ERR_STATUS);
+
+ for (offs = 0, bit = 1; offs < 8; offs++, bit <<= 1) {
+ if (tcstat & bit) {
+ writel(bit, dmac->regs + PL080_TC_CLEAR);
+ s3c64xx_dma_tcirq(dmac, offs);
+ }
+
+ if (errstat & bit) {
+ s3c64xx_dma_errirq(dmac, offs);
+ writel(bit, dmac->regs + PL080_ERR_CLEAR);
+ }
+ }
+
+ return IRQ_HANDLED;
+}
+
+static struct sysdev_class dma_sysclass = {
+ .name = "s3c64xx-dma",
+};
+
+static int s3c64xx_dma_init1(int chno, enum dma_ch chbase,
+ int irq, unsigned int base)
+{
+ struct s3c2410_dma_chan *chptr = &s3c2410_chans[chno];
+ struct s3c64xx_dmac *dmac;
+ char clkname[16];
+ void __iomem *regs;
+ void __iomem *regptr;
+ int err, ch;
+
+ dmac = kzalloc(sizeof(struct s3c64xx_dmac), GFP_KERNEL);
+ if (!dmac) {
+ printk(KERN_ERR "%s: failed to alloc mem\n", __func__);
+ return -ENOMEM;
+ }
+
+ dmac->sysdev.id = chno / 8;
+ dmac->sysdev.cls = &dma_sysclass;
+
+ err = sysdev_register(&dmac->sysdev);
+ if (err) {
+ printk(KERN_ERR "%s: failed to register sysdevice\n", __func__);
+ goto err_alloc;
+ }
+
+ regs = ioremap(base, 0x200);
+ if (!regs) {
+ printk(KERN_ERR "%s: failed to ioremap()\n", __func__);
+ err = -ENXIO;
+ goto err_dev;
+ }
+
+ snprintf(clkname, sizeof(clkname), "dma%d", dmac->sysdev.id);
+
+ dmac->clk = clk_get(NULL, clkname);
+ if (IS_ERR(dmac->clk)) {
+ printk(KERN_ERR "%s: failed to get clock %s\n", __func__, clkname);
+ err = PTR_ERR(dmac->clk);
+ goto err_map;
+ }
+
+ clk_enable(dmac->clk);
+
+ dmac->regs = regs;
+ dmac->chanbase = chbase;
+ dmac->channels = chptr;
+
+ err = request_irq(irq, s3c64xx_dma_irq, 0, "DMA", dmac);
+ if (err < 0) {
+ printk(KERN_ERR "%s: failed to get irq\n", __func__);
+ goto err_clk;
+ }
+
+ regptr = regs + PL080_Cx_BASE(0);
+
+ for (ch = 0; ch < 8; ch++, chno++, chptr++) {
+ printk(KERN_INFO "%s: registering DMA %d (%p)\n",
+ __func__, chno, regptr);
+
+ chptr->bit = 1 << ch;
+ chptr->number = chno;
+ chptr->dmac = dmac;
+ chptr->regs = regptr;
+ regptr += PL008_Cx_STRIDE;
+ }
+
+ /* for the moment, permanently enable the controller */
+ writel(PL080_CONFIG_ENABLE, regs + PL080_CONFIG);
+
+ printk(KERN_INFO "PL080: IRQ %d, at %p\n", irq, regs);
+
+ return 0;
+
+err_clk:
+ clk_disable(dmac->clk);
+ clk_put(dmac->clk);
+err_map:
+ iounmap(regs);
+err_dev:
+ sysdev_unregister(&dmac->sysdev);
+err_alloc:
+ kfree(dmac);
+ return err;
+}
+
+static int __init s3c64xx_dma_init(void)
+{
+ int ret;
+
+ printk(KERN_INFO "%s: Registering DMA channels\n", __func__);
+
+ dma_pool = dma_pool_create("DMA-LLI", NULL, 32, 16, 0);
+ if (!dma_pool) {
+ printk(KERN_ERR "%s: failed to create pool\n", __func__);
+ return -ENOMEM;
+ }
+
+ ret = sysdev_class_register(&dma_sysclass);
+ if (ret) {
+ printk(KERN_ERR "%s: failed to create sysclass\n", __func__);
+ return -ENOMEM;
+ }
+
+ /* Set all DMA configuration to be DMA, not SDMA */
+ writel(0xffffff, S3C_SYSREG(0x110));
+
+ /* Register standard DMA controlers */
+ s3c64xx_dma_init1(0, DMACH_UART0, IRQ_DMA0, 0x75000000);
+ s3c64xx_dma_init1(8, DMACH_PCM1_TX, IRQ_DMA1, 0x75100000);
+
+ return 0;
+}
+
+arch_initcall(s3c64xx_dma_init);
diff --git a/arch/arm/plat-s3c64xx/gpiolib.c b/arch/arm/plat-s3c64xx/gpiolib.c
index 78ee52c..da7b60e 100644
--- a/arch/arm/plat-s3c64xx/gpiolib.c
+++ b/arch/arm/plat-s3c64xx/gpiolib.c
@@ -385,12 +385,19 @@
{
chip->chip.direction_input = s3c64xx_gpiolib_4bit_input;
chip->chip.direction_output = s3c64xx_gpiolib_4bit_output;
+ chip->pm = __gpio_pm(&s3c_gpio_pm_4bit);
}
static __init void s3c64xx_gpiolib_add_4bit2(struct s3c_gpio_chip *chip)
{
chip->chip.direction_input = s3c64xx_gpiolib_4bit2_input;
chip->chip.direction_output = s3c64xx_gpiolib_4bit2_output;
+ chip->pm = __gpio_pm(&s3c_gpio_pm_4bit);
+}
+
+static __init void s3c64xx_gpiolib_add_2bit(struct s3c_gpio_chip *chip)
+{
+ chip->pm = __gpio_pm(&s3c_gpio_pm_2bit);
}
static __init void s3c64xx_gpiolib_add(struct s3c_gpio_chip *chips,
@@ -412,7 +419,8 @@
s3c64xx_gpiolib_add(gpio_4bit2, ARRAY_SIZE(gpio_4bit2),
s3c64xx_gpiolib_add_4bit2);
- s3c64xx_gpiolib_add(gpio_2bit, ARRAY_SIZE(gpio_2bit), NULL);
+ s3c64xx_gpiolib_add(gpio_2bit, ARRAY_SIZE(gpio_2bit),
+ s3c64xx_gpiolib_add_2bit);
return 0;
}
diff --git a/arch/arm/plat-s3c64xx/include/plat/dma-plat.h b/arch/arm/plat-s3c64xx/include/plat/dma-plat.h
new file mode 100644
index 0000000..0c30dd9
--- /dev/null
+++ b/arch/arm/plat-s3c64xx/include/plat/dma-plat.h
@@ -0,0 +1,70 @@
+/* linux/arch/arm/plat-s3c64xx/include/plat/dma-plat.h
+ *
+ * Copyright 2009 Openmoko, Inc.
+ * Copyright 2009 Simtec Electronics
+ * Ben Dooks <ben@simtec.co.uk>
+ * http://armlinux.simtec.co.uk/
+ *
+ * S3C64XX DMA core
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#define DMACH_LOW_LEVEL (1<<28) /* use this to specifiy hardware ch no */
+
+struct s3c64xx_dma_buff;
+
+/** s3c64xx_dma_buff - S3C64XX DMA buffer descriptor
+ * @next: Pointer to next buffer in queue or ring.
+ * @pw: Client provided identifier
+ * @lli: Pointer to hardware descriptor this buffer is associated with.
+ * @lli_dma: Hardare address of the descriptor.
+ */
+struct s3c64xx_dma_buff {
+ struct s3c64xx_dma_buff *next;
+
+ void *pw;
+ struct pl080_lli *lli;
+ dma_addr_t lli_dma;
+};
+
+struct s3c64xx_dmac;
+
+struct s3c2410_dma_chan {
+ unsigned char number; /* number of this dma channel */
+ unsigned char in_use; /* channel allocated */
+ unsigned char bit; /* bit for enable/disable/etc */
+ unsigned char hw_width;
+ unsigned char peripheral;
+
+ unsigned int flags;
+ enum s3c2410_dmasrc source;
+
+
+ dma_addr_t dev_addr;
+
+ struct s3c2410_dma_client *client;
+ struct s3c64xx_dmac *dmac; /* pointer to controller */
+
+ void __iomem *regs;
+
+ /* cdriver callbacks */
+ s3c2410_dma_cbfn_t callback_fn; /* buffer done callback */
+ s3c2410_dma_opfn_t op_fn; /* channel op callback */
+
+ /* buffer list and information */
+ struct s3c64xx_dma_buff *curr; /* current dma buffer */
+ struct s3c64xx_dma_buff *next; /* next buffer to load */
+ struct s3c64xx_dma_buff *end; /* end of queue */
+
+ /* note, when channel is running in circular mode, curr is the
+ * first buffer enqueued, end is the last and curr is where the
+ * last buffer-done event is set-at. The buffers are not freed
+ * and the last buffer hardware descriptor points back to the
+ * first.
+ */
+};
+
+#include <plat/dma-core.h>
diff --git a/arch/arm/plat-s3c64xx/include/plat/irqs.h b/arch/arm/plat-s3c64xx/include/plat/irqs.h
index f865bf4..743a700 100644
--- a/arch/arm/plat-s3c64xx/include/plat/irqs.h
+++ b/arch/arm/plat-s3c64xx/include/plat/irqs.h
@@ -157,6 +157,7 @@
#define S3C_EINT(x) ((x) + S3C_IRQ_EINT_BASE)
#define IRQ_EINT(x) S3C_EINT(x)
+#define IRQ_EINT_BIT(x) ((x) - S3C_EINT(0))
/* Next the external interrupt groups. These are similar to the IRQ_EINT(x)
* that they are sourced from the GPIO pins but with a different scheme for
diff --git a/arch/arm/plat-s3c64xx/include/plat/pm-core.h b/arch/arm/plat-s3c64xx/include/plat/pm-core.h
new file mode 100644
index 0000000..d347de3
--- /dev/null
+++ b/arch/arm/plat-s3c64xx/include/plat/pm-core.h
@@ -0,0 +1,98 @@
+/* linux/arch/arm/plat-s3c64xx/include/plat/pm-core.h
+ *
+ * Copyright 2008 Openmoko, Inc.
+ * Copyright 2008 Simtec Electronics
+ * Ben Dooks <ben@simtec.co.uk>
+ * http://armlinux.simtec.co.uk/
+ *
+ * S3C64XX - PM core support for arch/arm/plat-s3c/pm.c
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <plat/regs-gpio.h>
+
+static inline void s3c_pm_debug_init_uart(void)
+{
+ u32 tmp = __raw_readl(S3C_PCLK_GATE);
+
+ /* As a note, since the S3C64XX UARTs generally have multiple
+ * clock sources, we simply enable PCLK at the moment and hope
+ * that the resume settings for the UART are suitable for the
+ * use with PCLK.
+ */
+
+ tmp |= S3C_CLKCON_PCLK_UART0;
+ tmp |= S3C_CLKCON_PCLK_UART1;
+ tmp |= S3C_CLKCON_PCLK_UART2;
+ tmp |= S3C_CLKCON_PCLK_UART3;
+
+ __raw_writel(tmp, S3C_PCLK_GATE);
+ udelay(10);
+}
+
+static inline void s3c_pm_arch_prepare_irqs(void)
+{
+ /* VIC should have already been taken care of */
+
+ /* clear any pending EINT0 interrupts */
+ __raw_writel(__raw_readl(S3C64XX_EINT0PEND), S3C64XX_EINT0PEND);
+}
+
+static inline void s3c_pm_arch_stop_clocks(void)
+{
+}
+
+static inline void s3c_pm_arch_show_resume_irqs(void)
+{
+}
+
+/* make these defines, we currently do not have any need to change
+ * the IRQ wake controls depending on the CPU we are running on */
+
+#define s3c_irqwake_eintallow ((1 << 28) - 1)
+#define s3c_irqwake_intallow (0)
+
+static inline void s3c_pm_arch_update_uart(void __iomem *regs,
+ struct pm_uart_save *save)
+{
+ u32 ucon = __raw_readl(regs + S3C2410_UCON);
+ u32 ucon_clk = ucon & S3C6400_UCON_CLKMASK;
+ u32 save_clk = save->ucon & S3C6400_UCON_CLKMASK;
+ u32 new_ucon;
+ u32 delta;
+
+ /* S3C64XX UART blocks only support level interrupts, so ensure that
+ * when we restore unused UART blocks we force the level interrupt
+ * settigs. */
+ save->ucon |= S3C2410_UCON_TXILEVEL | S3C2410_UCON_RXILEVEL;
+
+ /* We have a constraint on changing the clock type of the UART
+ * between UCLKx and PCLK, so ensure that when we restore UCON
+ * that the CLK field is correctly modified if the bootloader
+ * has changed anything.
+ */
+ if (ucon_clk != save_clk) {
+ new_ucon = save->ucon;
+ delta = ucon_clk ^ save_clk;
+
+ /* change from UCLKx => wrong PCLK,
+ * either UCLK can be tested for by a bit-test
+ * with UCLK0 */
+ if (ucon_clk & S3C6400_UCON_UCLK0 &&
+ !(save_clk & S3C6400_UCON_UCLK0) &&
+ delta & S3C6400_UCON_PCLK2) {
+ new_ucon &= ~S3C6400_UCON_UCLK0;
+ } else if (delta == S3C6400_UCON_PCLK2) {
+ /* as an precaution, don't change from
+ * PCLK2 => PCLK or vice-versa */
+ new_ucon ^= S3C6400_UCON_PCLK2;
+ }
+
+ S3C_PMDBG("ucon change %04x => %04x (save=%04x)\n",
+ ucon, new_ucon, save->ucon);
+ save->ucon = new_ucon;
+ }
+}
diff --git a/arch/arm/plat-s3c64xx/include/plat/regs-clock.h b/arch/arm/plat-s3c64xx/include/plat/regs-clock.h
index b1082c1..52836d4 100644
--- a/arch/arm/plat-s3c64xx/include/plat/regs-clock.h
+++ b/arch/arm/plat-s3c64xx/include/plat/regs-clock.h
@@ -32,6 +32,7 @@
#define S3C_HCLK_GATE S3C_CLKREG(0x30)
#define S3C_PCLK_GATE S3C_CLKREG(0x34)
#define S3C_SCLK_GATE S3C_CLKREG(0x38)
+#define S3C_MEM0_GATE S3C_CLKREG(0x3C)
/* CLKDIV0 */
#define S3C6400_CLKDIV0_MFC_MASK (0xf << 28)
diff --git a/arch/arm/plat-s3c64xx/include/plat/s3c6400.h b/arch/arm/plat-s3c64xx/include/plat/s3c6400.h
index 571eaa2..11f2e1e 100644
--- a/arch/arm/plat-s3c64xx/include/plat/s3c6400.h
+++ b/arch/arm/plat-s3c64xx/include/plat/s3c6400.h
@@ -15,12 +15,13 @@
/* Common init code for S3C6400 related SoCs */
extern void s3c6400_common_init_uarts(struct s3c2410_uartcfg *cfg, int no);
-extern void s3c6400_register_clocks(void);
+extern void s3c6400_register_clocks(unsigned armclk_divlimit);
extern void s3c6400_setup_clocks(void);
#ifdef CONFIG_CPU_S3C6400
extern int s3c6400_init(void);
+extern void s3c6400_init_irq(void);
extern void s3c6400_map_io(void);
extern void s3c6400_init_clocks(int xtal);
diff --git a/arch/arm/plat-s3c64xx/irq-eint.c b/arch/arm/plat-s3c64xx/irq-eint.c
index 47e5155..f81b7b8 100644
--- a/arch/arm/plat-s3c64xx/irq-eint.c
+++ b/arch/arm/plat-s3c64xx/irq-eint.c
@@ -14,6 +14,7 @@
#include <linux/kernel.h>
#include <linux/interrupt.h>
+#include <linux/sysdev.h>
#include <linux/gpio.h>
#include <linux/irq.h>
#include <linux/io.h>
@@ -26,6 +27,7 @@
#include <mach/map.h>
#include <plat/cpu.h>
+#include <plat/pm.h>
#define eint_offset(irq) ((irq) - IRQ_EINT(0))
#define eint_irq_to_bit(irq) (1 << eint_offset(irq))
@@ -134,6 +136,7 @@
.mask_ack = s3c_irq_eint_maskack,
.ack = s3c_irq_eint_ack,
.set_type = s3c_irq_eint_set_type,
+ .set_wake = s3c_irqext_wake,
};
/* s3c_irq_demux_eint
diff --git a/arch/arm/plat-s3c64xx/irq-pm.c b/arch/arm/plat-s3c64xx/irq-pm.c
new file mode 100644
index 0000000..ca523b5
--- /dev/null
+++ b/arch/arm/plat-s3c64xx/irq-pm.c
@@ -0,0 +1,111 @@
+/* arch/arm/plat-s3c64xx/irq-pm.c
+ *
+ * Copyright 2008 Openmoko, Inc.
+ * Copyright 2008 Simtec Electronics
+ * Ben Dooks <ben@simtec.co.uk>
+ * http://armlinux.simtec.co.uk/
+ *
+ * S3C64XX - Interrupt handling Power Management
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/sysdev.h>
+#include <linux/interrupt.h>
+#include <linux/serial_core.h>
+#include <linux/irq.h>
+#include <linux/io.h>
+
+#include <mach/map.h>
+
+#include <plat/regs-serial.h>
+#include <plat/regs-timer.h>
+#include <plat/regs-gpio.h>
+#include <plat/cpu.h>
+#include <plat/pm.h>
+
+/* We handled all the IRQ types in this code, to save having to make several
+ * small files to handle each different type separately. Having the EINT_GRP
+ * code here shouldn't be as much bloat as the IRQ table space needed when
+ * they are enabled. The added benefit is we ensure that these registers are
+ * in the same state as we suspended.
+ */
+
+static struct sleep_save irq_save[] = {
+ SAVE_ITEM(S3C64XX_PRIORITY),
+ SAVE_ITEM(S3C64XX_EINT0CON0),
+ SAVE_ITEM(S3C64XX_EINT0CON1),
+ SAVE_ITEM(S3C64XX_EINT0FLTCON0),
+ SAVE_ITEM(S3C64XX_EINT0FLTCON1),
+ SAVE_ITEM(S3C64XX_EINT0FLTCON2),
+ SAVE_ITEM(S3C64XX_EINT0FLTCON3),
+ SAVE_ITEM(S3C64XX_EINT0MASK),
+ SAVE_ITEM(S3C64XX_TINT_CSTAT),
+};
+
+static struct irq_grp_save {
+ u32 fltcon;
+ u32 con;
+ u32 mask;
+} eint_grp_save[5];
+
+static u32 irq_uart_mask[CONFIG_SERIAL_SAMSUNG_UARTS];
+
+static int s3c64xx_irq_pm_suspend(struct sys_device *dev, pm_message_t state)
+{
+ struct irq_grp_save *grp = eint_grp_save;
+ int i;
+
+ S3C_PMDBG("%s: suspending IRQs\n", __func__);
+
+ s3c_pm_do_save(irq_save, ARRAY_SIZE(irq_save));
+
+ for (i = 0; i < CONFIG_SERIAL_SAMSUNG_UARTS; i++)
+ irq_uart_mask[i] = __raw_readl(S3C_VA_UARTx(i) + S3C64XX_UINTM);
+
+ for (i = 0; i < ARRAY_SIZE(eint_grp_save); i++, grp++) {
+ grp->con = __raw_readl(S3C64XX_EINT12CON + (i * 4));
+ grp->mask = __raw_readl(S3C64XX_EINT12MASK + (i * 4));
+ grp->fltcon = __raw_readl(S3C64XX_EINT12FLTCON + (i * 4));
+ }
+
+ return 0;
+}
+
+static int s3c64xx_irq_pm_resume(struct sys_device *dev)
+{
+ struct irq_grp_save *grp = eint_grp_save;
+ int i;
+
+ S3C_PMDBG("%s: resuming IRQs\n", __func__);
+
+ s3c_pm_do_restore(irq_save, ARRAY_SIZE(irq_save));
+
+ for (i = 0; i < CONFIG_SERIAL_SAMSUNG_UARTS; i++)
+ __raw_writel(irq_uart_mask[i], S3C_VA_UARTx(i) + S3C64XX_UINTM);
+
+ for (i = 0; i < ARRAY_SIZE(eint_grp_save); i++, grp++) {
+ __raw_writel(grp->con, S3C64XX_EINT12CON + (i * 4));
+ __raw_writel(grp->mask, S3C64XX_EINT12MASK + (i * 4));
+ __raw_writel(grp->fltcon, S3C64XX_EINT12FLTCON + (i * 4));
+ }
+
+ S3C_PMDBG("%s: IRQ configuration restored\n", __func__);
+ return 0;
+}
+
+static struct sysdev_driver s3c64xx_irq_driver = {
+ .suspend = s3c64xx_irq_pm_suspend,
+ .resume = s3c64xx_irq_pm_resume,
+};
+
+static int __init s3c64xx_irq_pm_init(void)
+{
+ return sysdev_driver_register(&s3c64xx_sysclass, &s3c64xx_irq_driver);
+}
+
+arch_initcall(s3c64xx_irq_pm_init);
+
diff --git a/arch/arm/plat-s3c64xx/irq.c b/arch/arm/plat-s3c64xx/irq.c
index f22edf7..8dc5b6d 100644
--- a/arch/arm/plat-s3c64xx/irq.c
+++ b/arch/arm/plat-s3c64xx/irq.c
@@ -14,12 +14,14 @@
#include <linux/kernel.h>
#include <linux/interrupt.h>
+#include <linux/serial_core.h>
#include <linux/irq.h>
#include <linux/io.h>
#include <asm/hardware/vic.h>
#include <mach/map.h>
+#include <plat/regs-serial.h>
#include <plat/regs-timer.h>
#include <plat/cpu.h>
@@ -135,9 +137,6 @@
}
/* UART interrupt registers, not worth adding to seperate include header */
-#define S3C64XX_UINTP 0x30
-#define S3C64XX_UINTSP 0x34
-#define S3C64XX_UINTM 0x38
static void s3c_irq_uart_mask(unsigned int irq)
{
@@ -233,8 +232,8 @@
printk(KERN_DEBUG "%s: initialising interrupts\n", __func__);
/* initialise the pair of VICs */
- vic_init(S3C_VA_VIC0, S3C_VIC0_BASE, vic0_valid);
- vic_init(S3C_VA_VIC1, S3C_VIC1_BASE, vic1_valid);
+ vic_init(S3C_VA_VIC0, S3C_VIC0_BASE, vic0_valid, 0);
+ vic_init(S3C_VA_VIC1, S3C_VIC1_BASE, vic1_valid, 0);
/* add the timer sub-irqs */
diff --git a/arch/arm/plat-s3c64xx/pm.c b/arch/arm/plat-s3c64xx/pm.c
new file mode 100644
index 0000000..07a6516
--- /dev/null
+++ b/arch/arm/plat-s3c64xx/pm.c
@@ -0,0 +1,175 @@
+/* linux/arch/arm/plat-s3c64xx/pm.c
+ *
+ * Copyright 2008 Openmoko, Inc.
+ * Copyright 2008 Simtec Electronics
+ * Ben Dooks <ben@simtec.co.uk>
+ * http://armlinux.simtec.co.uk/
+ *
+ * S3C64XX CPU PM support.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/init.h>
+#include <linux/suspend.h>
+#include <linux/serial_core.h>
+#include <linux/io.h>
+
+#include <mach/map.h>
+
+#include <plat/pm.h>
+#include <plat/regs-sys.h>
+#include <plat/regs-gpio.h>
+#include <plat/regs-clock.h>
+#include <plat/regs-syscon-power.h>
+#include <plat/regs-gpio-memport.h>
+
+#ifdef CONFIG_S3C_PM_DEBUG_LED_SMDK
+#include <plat/gpio-bank-n.h>
+
+void s3c_pm_debug_smdkled(u32 set, u32 clear)
+{
+ unsigned long flags;
+ u32 reg;
+
+ local_irq_save(flags);
+ reg = __raw_readl(S3C64XX_GPNCON);
+ reg &= ~(S3C64XX_GPN_CONMASK(12) | S3C64XX_GPN_CONMASK(13) |
+ S3C64XX_GPN_CONMASK(14) | S3C64XX_GPN_CONMASK(15));
+ reg |= S3C64XX_GPN_OUTPUT(12) | S3C64XX_GPN_OUTPUT(13) |
+ S3C64XX_GPN_OUTPUT(14) | S3C64XX_GPN_OUTPUT(15);
+ __raw_writel(reg, S3C64XX_GPNCON);
+
+ reg = __raw_readl(S3C64XX_GPNDAT);
+ reg &= ~(clear << 12);
+ reg |= set << 12;
+ __raw_writel(reg, S3C64XX_GPNDAT);
+
+ local_irq_restore(flags);
+}
+#endif
+
+static struct sleep_save core_save[] = {
+ SAVE_ITEM(S3C_APLL_LOCK),
+ SAVE_ITEM(S3C_MPLL_LOCK),
+ SAVE_ITEM(S3C_EPLL_LOCK),
+ SAVE_ITEM(S3C_CLK_SRC),
+ SAVE_ITEM(S3C_CLK_DIV0),
+ SAVE_ITEM(S3C_CLK_DIV1),
+ SAVE_ITEM(S3C_CLK_DIV2),
+ SAVE_ITEM(S3C_CLK_OUT),
+ SAVE_ITEM(S3C_HCLK_GATE),
+ SAVE_ITEM(S3C_PCLK_GATE),
+ SAVE_ITEM(S3C_SCLK_GATE),
+ SAVE_ITEM(S3C_MEM0_GATE),
+
+ SAVE_ITEM(S3C_EPLL_CON1),
+ SAVE_ITEM(S3C_EPLL_CON0),
+
+ SAVE_ITEM(S3C64XX_MEM0DRVCON),
+ SAVE_ITEM(S3C64XX_MEM1DRVCON),
+
+#ifndef CONFIG_CPU_FREQ
+ SAVE_ITEM(S3C_APLL_CON),
+ SAVE_ITEM(S3C_MPLL_CON),
+#endif
+};
+
+static struct sleep_save misc_save[] = {
+ SAVE_ITEM(S3C64XX_AHB_CON0),
+ SAVE_ITEM(S3C64XX_AHB_CON1),
+ SAVE_ITEM(S3C64XX_AHB_CON2),
+
+ SAVE_ITEM(S3C64XX_SPCON),
+
+ SAVE_ITEM(S3C64XX_MEM0CONSTOP),
+ SAVE_ITEM(S3C64XX_MEM1CONSTOP),
+ SAVE_ITEM(S3C64XX_MEM0CONSLP0),
+ SAVE_ITEM(S3C64XX_MEM0CONSLP1),
+ SAVE_ITEM(S3C64XX_MEM1CONSLP),
+};
+
+void s3c_pm_configure_extint(void)
+{
+ __raw_writel(s3c_irqwake_eintmask, S3C64XX_EINT_MASK);
+}
+
+void s3c_pm_restore_core(void)
+{
+ __raw_writel(0, S3C64XX_EINT_MASK);
+
+ s3c_pm_debug_smdkled(1 << 2, 0);
+
+ s3c_pm_do_restore_core(core_save, ARRAY_SIZE(core_save));
+ s3c_pm_do_restore(misc_save, ARRAY_SIZE(misc_save));
+}
+
+void s3c_pm_save_core(void)
+{
+ s3c_pm_do_save(misc_save, ARRAY_SIZE(misc_save));
+ s3c_pm_do_save(core_save, ARRAY_SIZE(core_save));
+}
+
+/* since both s3c6400 and s3c6410 share the same sleep pm calls, we
+ * put the per-cpu code in here until any new cpu comes along and changes
+ * this.
+ */
+
+#include <plat/regs-gpio.h>
+
+static void s3c64xx_cpu_suspend(void)
+{
+ unsigned long tmp;
+
+ /* set our standby method to sleep */
+
+ tmp = __raw_readl(S3C64XX_PWR_CFG);
+ tmp &= ~S3C64XX_PWRCFG_CFG_WFI_MASK;
+ tmp |= S3C64XX_PWRCFG_CFG_WFI_SLEEP;
+ __raw_writel(tmp, S3C64XX_PWR_CFG);
+
+ /* clear any old wakeup */
+
+ __raw_writel(__raw_readl(S3C64XX_WAKEUP_STAT),
+ S3C64XX_WAKEUP_STAT);
+
+ /* set the LED state to 0110 over sleep */
+ s3c_pm_debug_smdkled(3 << 1, 0xf);
+
+ /* issue the standby signal into the pm unit. Note, we
+ * issue a write-buffer drain just in case */
+
+ tmp = 0;
+
+ asm("b 1f\n\t"
+ ".align 5\n\t"
+ "1:\n\t"
+ "mcr p15, 0, %0, c7, c10, 5\n\t"
+ "mcr p15, 0, %0, c7, c10, 4\n\t"
+ "mcr p15, 0, %0, c7, c0, 4" :: "r" (tmp));
+
+ /* we should never get past here */
+
+ panic("sleep resumed to originator?");
+}
+
+static void s3c64xx_pm_prepare(void)
+{
+ /* store address of resume. */
+ __raw_writel(virt_to_phys(s3c_cpu_resume), S3C64XX_INFORM0);
+
+ /* ensure previous wakeup state is cleared before sleeping */
+ __raw_writel(__raw_readl(S3C64XX_WAKEUP_STAT), S3C64XX_WAKEUP_STAT);
+}
+
+static int s3c64xx_pm_init(void)
+{
+ pm_cpu_prep = s3c64xx_pm_prepare;
+ pm_cpu_sleep = s3c64xx_cpu_suspend;
+ pm_uart_udivslot = 1;
+ return 0;
+}
+
+arch_initcall(s3c64xx_pm_init);
diff --git a/arch/arm/plat-s3c64xx/s3c6400-clock.c b/arch/arm/plat-s3c64xx/s3c6400-clock.c
index 05b1752..1debc1f 100644
--- a/arch/arm/plat-s3c64xx/s3c6400-clock.c
+++ b/arch/arm/plat-s3c64xx/s3c6400-clock.c
@@ -133,6 +133,65 @@
.sources = &clk_src_mpll,
};
+static unsigned int armclk_mask;
+
+static unsigned long s3c64xx_clk_arm_get_rate(struct clk *clk)
+{
+ unsigned long rate = clk_get_rate(clk->parent);
+ u32 clkdiv;
+
+ /* divisor mask starts at bit0, so no need to shift */
+ clkdiv = __raw_readl(S3C_CLK_DIV0) & armclk_mask;
+
+ return rate / (clkdiv + 1);
+}
+
+static unsigned long s3c64xx_clk_arm_round_rate(struct clk *clk,
+ unsigned long rate)
+{
+ unsigned long parent = clk_get_rate(clk->parent);
+ u32 div;
+
+ if (parent < rate)
+ return rate;
+
+ div = (parent / rate) - 1;
+ if (div > armclk_mask)
+ div = armclk_mask;
+
+ return parent / (div + 1);
+}
+
+static int s3c64xx_clk_arm_set_rate(struct clk *clk, unsigned long rate)
+{
+ unsigned long parent = clk_get_rate(clk->parent);
+ u32 div;
+ u32 val;
+
+ if (rate < parent / (armclk_mask + 1))
+ return -EINVAL;
+
+ rate = clk_round_rate(clk, rate);
+ div = clk_get_rate(clk->parent) / rate;
+
+ val = __raw_readl(S3C_CLK_DIV0);
+ val &= armclk_mask;
+ val |= (div - 1);
+ __raw_writel(val, S3C_CLK_DIV0);
+
+ return 0;
+
+}
+
+static struct clk clk_arm = {
+ .name = "armclk",
+ .id = -1,
+ .parent = &clk_mout_apll.clk,
+ .get_rate = s3c64xx_clk_arm_get_rate,
+ .set_rate = s3c64xx_clk_arm_set_rate,
+ .round_rate = s3c64xx_clk_arm_round_rate,
+};
+
static unsigned long s3c64xx_clk_doutmpll_get_rate(struct clk *clk)
{
unsigned long rate = clk_get_rate(clk->parent);
@@ -520,6 +579,33 @@
.reg_divider = S3C_CLK_DIV2,
};
+static struct clk *clkset_camif_list[] = {
+ &clk_h2,
+};
+
+static struct clk_sources clkset_camif = {
+ .sources = clkset_camif_list,
+ .nr_sources = ARRAY_SIZE(clkset_camif_list),
+};
+
+static struct clksrc_clk clk_camif = {
+ .clk = {
+ .name = "camera",
+ .id = -1,
+ .ctrlbit = S3C_CLKCON_SCLK_CAM,
+ .enable = s3c64xx_sclk_ctrl,
+ .set_parent = s3c64xx_setparent_clksrc,
+ .get_rate = s3c64xx_getrate_clksrc,
+ .set_rate = s3c64xx_setrate_clksrc,
+ .round_rate = s3c64xx_roundrate_clksrc,
+ },
+ .shift = 0,
+ .mask = 0,
+ .sources = &clkset_camif,
+ .divider_shift = S3C6400_CLKDIV0_CAM_SHIFT,
+ .reg_divider = S3C_CLK_DIV0,
+};
+
/* Clock initialisation code */
static struct clksrc_clk *init_parents[] = {
@@ -536,6 +622,7 @@
&clk_audio0,
&clk_audio1,
&clk_irda,
+ &clk_camif,
};
static void __init_or_cpufreq s3c6400_set_clksrc(struct clksrc_clk *clk)
@@ -608,6 +695,7 @@
clk_fout_epll.rate = epll;
clk_fout_apll.rate = apll;
+ clk_h2.rate = hclk2;
clk_h.rate = hclk;
clk_p.rate = pclk;
clk_f.rate = fclk;
@@ -635,14 +723,30 @@
&clk_audio0.clk,
&clk_audio1.clk,
&clk_irda.clk,
+ &clk_camif.clk,
+ &clk_arm,
};
-void __init s3c6400_register_clocks(void)
+/**
+ * s3c6400_register_clocks - register clocks for s3c6400 and above
+ * @armclk_divlimit: Divisor mask for ARMCLK
+ *
+ * Register the clocks for the S3C6400 and above SoC range, such
+ * as ARMCLK and the clocks which have divider chains attached.
+ *
+ * This call does not setup the clocks, which is left to the
+ * s3c6400_setup_clocks() call which may be needed by the cpufreq
+ * or resume code to re-set the clocks if the bootloader has changed
+ * them.
+ */
+void __init s3c6400_register_clocks(unsigned armclk_divlimit)
{
struct clk *clkp;
int ret;
int ptr;
+ armclk_mask = armclk_divlimit;
+
for (ptr = 0; ptr < ARRAY_SIZE(clks); ptr++) {
clkp = clks[ptr];
ret = s3c24xx_register_clock(clkp);
diff --git a/arch/arm/plat-s3c64xx/setup-sdhci-gpio.c b/arch/arm/plat-s3c64xx/setup-sdhci-gpio.c
new file mode 100644
index 0000000..5417123
--- /dev/null
+++ b/arch/arm/plat-s3c64xx/setup-sdhci-gpio.c
@@ -0,0 +1,55 @@
+/* linux/arch/arm/plat-s3c64xx/setup-sdhci-gpio.c
+ *
+ * Copyright 2008 Simtec Electronics
+ * Ben Dooks <ben@simtec.co.uk>
+ * http://armlinux.simtec.co.uk/
+ *
+ * S3C64XX - Helper functions for setting up SDHCI device(s) GPIO (HSMMC)
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+
+#include <mach/gpio.h>
+#include <plat/gpio-cfg.h>
+
+void s3c64xx_setup_sdhci0_cfg_gpio(struct platform_device *dev, int width)
+{
+ unsigned int gpio;
+ unsigned int end;
+
+ end = S3C64XX_GPG(2 + width);
+
+ /* Set all the necessary GPG pins to special-function 0 */
+ for (gpio = S3C64XX_GPG(0); gpio < end; gpio++) {
+ s3c_gpio_cfgpin(gpio, S3C_GPIO_SFN(2));
+ s3c_gpio_setpull(gpio, S3C_GPIO_PULL_NONE);
+ }
+
+ s3c_gpio_setpull(S3C64XX_GPG(6), S3C_GPIO_PULL_UP);
+ s3c_gpio_cfgpin(S3C64XX_GPG(6), S3C_GPIO_SFN(2));
+}
+
+void s3c64xx_setup_sdhci1_cfg_gpio(struct platform_device *dev, int width)
+{
+ unsigned int gpio;
+ unsigned int end;
+
+ end = S3C64XX_GPH(2 + width);
+
+ /* Set all the necessary GPG pins to special-function 0 */
+ for (gpio = S3C64XX_GPH(0); gpio < end; gpio++) {
+ s3c_gpio_cfgpin(gpio, S3C_GPIO_SFN(2));
+ s3c_gpio_setpull(gpio, S3C_GPIO_PULL_NONE);
+ }
+
+ s3c_gpio_setpull(S3C64XX_GPG(6), S3C_GPIO_PULL_UP);
+ s3c_gpio_cfgpin(S3C64XX_GPG(6), S3C_GPIO_SFN(3));
+}
diff --git a/arch/arm/plat-s3c64xx/sleep.S b/arch/arm/plat-s3c64xx/sleep.S
new file mode 100644
index 0000000..8e71fe9
--- /dev/null
+++ b/arch/arm/plat-s3c64xx/sleep.S
@@ -0,0 +1,144 @@
+/* linux/0arch/arm/plat-s3c64xx/sleep.S
+ *
+ * Copyright 2008 Openmoko, Inc.
+ * Copyright 2008 Simtec Electronics
+ * Ben Dooks <ben@simtec.co.uk>
+ * http://armlinux.simtec.co.uk/
+ *
+ * S3C64XX CPU sleep code
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/linkage.h>
+#include <asm/assembler.h>
+#include <mach/map.h>
+
+#undef S3C64XX_VA_GPIO
+#define S3C64XX_VA_GPIO (0x0)
+
+#include <plat/regs-gpio.h>
+#include <plat/gpio-bank-n.h>
+
+#define LL_UART (S3C_PA_UART + (0x400 * CONFIG_S3C_LOWLEVEL_UART_PORT))
+
+ .text
+
+ /* s3c_cpu_save
+ *
+ * Save enough processor state to allow the restart of the pm.c
+ * code after resume.
+ *
+ * entry:
+ * r0 = pointer to the save block
+ */
+
+ENTRY(s3c_cpu_save)
+ stmfd sp!, { r4 - r12, lr }
+
+ mrc p15, 0, r4, c13, c0, 0 @ FCSE/PID
+ mrc p15, 0, r5, c3, c0, 0 @ Domain ID
+ mrc p15, 0, r6, c2, c0, 0 @ Translation Table BASE0
+ mrc p15, 0, r7, c2, c0, 1 @ Translation Table BASE1
+ mrc p15, 0, r8, c2, c0, 2 @ Translation Table Control
+ mrc p15, 0, r9, c1, c0, 0 @ Control register
+ mrc p15, 0, r10, c1, c0, 1 @ Auxiliary control register
+ mrc p15, 0, r11, c1, c0, 2 @ Co-processor access controls
+
+ stmia r0, { r4 - r13 } @ Save CP registers and SP
+
+ @@ save our state to ram
+ bl s3c_pm_cb_flushcache
+
+ @@ call final suspend code
+ ldr r0, =pm_cpu_sleep
+ ldr pc, [r0]
+
+ @@ return to the caller, after the MMU is turned on.
+ @@ restore the last bits of the stack and return.
+resume_with_mmu:
+ ldmfd sp!, { r4 - r12, pc } @ return, from sp from s3c_cpu_save
+
+ .data
+
+ /* the next bit is code, but it requires easy access to the
+ * s3c_sleep_save_phys data before the MMU is switched on, so
+ * we store the code that needs this variable in the .data where
+ * the value can be written to (the .text segment is RO).
+ */
+
+ .global s3c_sleep_save_phys
+s3c_sleep_save_phys:
+ .word 0
+
+ /* Sleep magic, the word before the resume entry point so that the
+ * bootloader can check for a resumeable image. */
+
+ .word 0x2bedf00d
+
+ /* s3c_cpu_reusme
+ *
+ * This is the entry point, stored by whatever method the bootloader
+ * requires to get the kernel runnign again. This code expects to be
+ * entered with no caches live and the MMU disabled. It will then
+ * restore the MMU and other basic CP registers saved and restart
+ * the kernel C code to finish the resume code.
+ */
+
+ENTRY(s3c_cpu_resume)
+ msr cpsr_c, #PSR_I_BIT | PSR_F_BIT | SVC_MODE
+ ldr r2, =LL_UART /* for debug */
+
+#ifdef CONFIG_S3C_PM_DEBUG_LED_SMDK
+ /* Initialise the GPIO state if we are debugging via the SMDK LEDs,
+ * as the uboot version supplied resets these to inputs during the
+ * resume checks.
+ */
+
+ ldr r3, =S3C64XX_PA_GPIO
+ ldr r0, [ r3, #S3C64XX_GPNCON ]
+ bic r0, r0, #(S3C64XX_GPN_CONMASK(12) | S3C64XX_GPN_CONMASK(13) | \
+ S3C64XX_GPN_CONMASK(14) | S3C64XX_GPN_CONMASK(15))
+ orr r0, r0, #(S3C64XX_GPN_OUTPUT(12) | S3C64XX_GPN_OUTPUT(13) | \
+ S3C64XX_GPN_OUTPUT(14) | S3C64XX_GPN_OUTPUT(15))
+ str r0, [ r3, #S3C64XX_GPNCON ]
+
+ ldr r0, [ r3, #S3C64XX_GPNDAT ]
+ bic r0, r0, #0xf << 12 @ GPN12..15
+ orr r0, r0, #1 << 15 @ GPN15
+ str r0, [ r3, #S3C64XX_GPNDAT ]
+#endif
+
+ /* __v6_setup from arch/arm/mm/proc-v6.S, ensure that the caches
+ * are thoroughly cleaned just in case the bootloader didn't do it
+ * for us. */
+ mov r0, #0
+ mcr p15, 0, r0, c7, c14, 0 @ clean+invalidate D cache
+ mcr p15, 0, r0, c7, c5, 0 @ invalidate I cache
+ mcr p15, 0, r0, c7, c15, 0 @ clean+invalidate cache
+ mcr p15, 0, r0, c7, c10, 4 @ drain write buffer
+ @@mcr p15, 0, r0, c8, c7, 0 @ invalidate I + D TLBs
+ @@mcr p15, 0, r0, c7, c7, 0 @ Invalidate I + D caches
+
+ ldr r0, s3c_sleep_save_phys
+ ldmia r0, { r4 - r13 }
+
+ mcr p15, 0, r4, c13, c0, 0 @ FCSE/PID
+ mcr p15, 0, r5, c3, c0, 0 @ Domain ID
+ mcr p15, 0, r6, c2, c0, 0 @ Translation Table BASE0
+ mcr p15, 0, r7, c2, c0, 1 @ Translation Table BASE1
+ mcr p15, 0, r8, c2, c0, 2 @ Translation Table Control
+ mcr p15, 0, r10, c1, c0, 1 @ Auxiliary control register
+
+ mov r0, #0 @ restore copro access controls
+ mcr p15, 0, r11, c1, c0, 2 @ Co-processor access controls
+ mcr p15, 0, r0, c7, c5, 4
+
+ ldr r2, =resume_with_mmu
+ mcr p15, 0, r9, c1, c0, 0 /* turn mmu back on */
+ nop
+ mov pc, r2 /* jump back */
+
+ .end
diff --git a/drivers/leds/leds-h1940.c b/drivers/leds/leds-h1940.c
index 1aa46a3..173d104 100644
--- a/drivers/leds/leds-h1940.c
+++ b/drivers/leds/leds-h1940.c
@@ -16,6 +16,8 @@
#include <linux/string.h>
#include <linux/ctype.h>
#include <linux/leds.h>
+#include <linux/gpio.h>
+
#include <mach/regs-gpio.h>
#include <mach/hardware.h>
#include <mach/h1940-latch.h>
diff --git a/drivers/leds/leds-s3c24xx.c b/drivers/leds/leds-s3c24xx.c
index aa2e7ae..aa7acf3 100644
--- a/drivers/leds/leds-s3c24xx.c
+++ b/drivers/leds/leds-s3c24xx.c
@@ -15,6 +15,7 @@
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/leds.h>
+#include <linux/gpio.h>
#include <mach/hardware.h>
#include <mach/regs-gpio.h>
diff --git a/drivers/mmc/host/s3cmci.c b/drivers/mmc/host/s3cmci.c
index 2db166b..4eb4f37 100644
--- a/drivers/mmc/host/s3cmci.c
+++ b/drivers/mmc/host/s3cmci.c
@@ -17,6 +17,7 @@
#include <linux/mmc/host.h>
#include <linux/platform_device.h>
#include <linux/cpufreq.h>
+#include <linux/gpio.h>
#include <linux/irq.h>
#include <linux/io.h>
@@ -789,7 +790,7 @@
last_source = source;
- s3c2410_dma_devconfig(host->dma, source, 3,
+ s3c2410_dma_devconfig(host->dma, source,
host->mem->start + host->sdidata);
if (!setup_ok) {
@@ -1121,7 +1122,7 @@
case MMC_POWER_OFF:
default:
s3c2410_gpio_setpin(S3C2410_GPE5, 0);
- s3c2410_gpio_cfgpin(S3C2410_GPE5, S3C2410_GPE5_OUTP);
+ s3c2410_gpio_cfgpin(S3C2410_GPE5, S3C2410_GPIO_OUTPUT);
if (host->is2440)
mci_con |= S3C2440_SDICON_SDRESET;
diff --git a/drivers/spi/spi_s3c24xx_gpio.c b/drivers/spi/spi_s3c24xx_gpio.c
index f2447a5..bbf9371 100644
--- a/drivers/spi/spi_s3c24xx_gpio.c
+++ b/drivers/spi/spi_s3c24xx_gpio.c
@@ -17,6 +17,7 @@
#include <linux/spinlock.h>
#include <linux/workqueue.h>
#include <linux/platform_device.h>
+#include <linux/gpio.h>
#include <linux/spi/spi.h>
#include <linux/spi/spi_bitbang.h>
diff --git a/sound/soc/s3c24xx/s3c2412-i2s.c b/sound/soc/s3c24xx/s3c2412-i2s.c
index b7e0b3f..c35b74b 100644
--- a/sound/soc/s3c24xx/s3c2412-i2s.c
+++ b/sound/soc/s3c24xx/s3c2412-i2s.c
@@ -20,6 +20,7 @@
#include <linux/module.h>
#include <linux/device.h>
#include <linux/delay.h>
+#include <linux/gpio.h>
#include <linux/clk.h>
#include <linux/kernel.h>
#include <linux/io.h>
diff --git a/sound/soc/s3c24xx/s3c2443-ac97.c b/sound/soc/s3c24xx/s3c2443-ac97.c
index 3698f70..3f03d5d 100644
--- a/sound/soc/s3c24xx/s3c2443-ac97.c
+++ b/sound/soc/s3c24xx/s3c2443-ac97.c
@@ -19,6 +19,7 @@
#include <linux/io.h>
#include <linux/wait.h>
#include <linux/delay.h>
+#include <linux/gpio.h>
#include <linux/clk.h>
#include <sound/core.h>
diff --git a/sound/soc/s3c24xx/s3c24xx-i2s.c b/sound/soc/s3c24xx/s3c24xx-i2s.c
index cc06696..556e35f 100644
--- a/sound/soc/s3c24xx/s3c24xx-i2s.c
+++ b/sound/soc/s3c24xx/s3c24xx-i2s.c
@@ -21,6 +21,8 @@
#include <linux/clk.h>
#include <linux/jiffies.h>
#include <linux/io.h>
+#include <linux/gpio.h>
+
#include <sound/core.h>
#include <sound/pcm.h>
#include <sound/pcm_params.h>
diff --git a/sound/soc/s3c24xx/s3c24xx-pcm.c b/sound/soc/s3c24xx/s3c24xx-pcm.c
index 169ddad..eecfa5e 100644
--- a/sound/soc/s3c24xx/s3c24xx-pcm.c
+++ b/sound/soc/s3c24xx/s3c24xx-pcm.c
@@ -218,24 +218,17 @@
* sync to pclk, half-word transfers to the IIS-FIFO. */
if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) {
s3c2410_dma_devconfig(prtd->params->channel,
- S3C2410_DMASRC_MEM, S3C2410_DISRCC_INC |
- S3C2410_DISRCC_APB, prtd->params->dma_addr);
-
- s3c2410_dma_config(prtd->params->channel,
- prtd->params->dma_size,
- S3C2410_DCON_SYNC_PCLK |
- S3C2410_DCON_HANDSHAKE);
+ S3C2410_DMASRC_MEM,
+ prtd->params->dma_addr);
} else {
- s3c2410_dma_config(prtd->params->channel,
- prtd->params->dma_size,
- S3C2410_DCON_HANDSHAKE |
- S3C2410_DCON_SYNC_PCLK);
-
s3c2410_dma_devconfig(prtd->params->channel,
- S3C2410_DMASRC_HW, 0x3,
- prtd->params->dma_addr);
+ S3C2410_DMASRC_HW,
+ prtd->params->dma_addr);
}
+ s3c2410_dma_config(prtd->params->channel,
+ prtd->params->dma_size);
+
/* flush the DMA channel */
s3c2410_dma_ctrl(prtd->params->channel, S3C2410_DMAOP_FLUSH);
prtd->dma_loaded = 0;