igb: cleanup whitespace issues in igb_main.c
This patch goes through and cleans up whitespace issues in igb_main.c
to help improve readability.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
diff --git a/drivers/net/igb/igb_main.c b/drivers/net/igb/igb_main.c
index 1a6c074..b044c98 100644
--- a/drivers/net/igb/igb_main.c
+++ b/drivers/net/igb/igb_main.c
@@ -1006,7 +1006,6 @@
ctrl_ext & ~E1000_CTRL_EXT_DRV_LOAD);
}
-
/**
* igb_get_hw_control - get control of the h/w from f/w
* @adapter: address of board private structure
@@ -1067,7 +1066,6 @@
* igb_up - Open the interface and prepare it to handle traffic
* @adapter: board private structure
**/
-
int igb_up(struct igb_adapter *adapter)
{
struct e1000_hw *hw = &adapter->hw;
@@ -1288,7 +1286,7 @@
}
static const struct net_device_ops igb_netdev_ops = {
- .ndo_open = igb_open,
+ .ndo_open = igb_open,
.ndo_stop = igb_close,
.ndo_start_xmit = igb_xmit_frame_adv,
.ndo_get_stats = igb_get_stats,
@@ -1444,7 +1442,6 @@
netdev->features |= NETIF_F_IPV6_CSUM;
netdev->features |= NETIF_F_TSO;
netdev->features |= NETIF_F_TSO6;
-
netdev->features |= NETIF_F_GRO;
netdev->vlan_features |= NETIF_F_TSO;
@@ -1569,7 +1566,6 @@
}
#endif
-
switch (hw->mac.type) {
case e1000_82576:
/*
@@ -1624,8 +1620,8 @@
/* print bus type/speed/width info */
dev_info(&pdev->dev, "%s: (PCIe:%s:%s) %pM\n",
netdev->name,
- ((hw->bus.speed == e1000_bus_speed_2500)
- ? "2.5Gb/s" : "unknown"),
+ ((hw->bus.speed == e1000_bus_speed_2500) ? "2.5Gb/s" :
+ "unknown"),
((hw->bus.width == e1000_bus_width_pcie_x4) ? "Width x4" :
(hw->bus.width == e1000_bus_width_pcie_x2) ? "Width x2" :
(hw->bus.width == e1000_bus_width_pcie_x1) ? "Width x1" :
@@ -1658,8 +1654,8 @@
err_ioremap:
free_netdev(netdev);
err_alloc_etherdev:
- pci_release_selected_regions(pdev, pci_select_bars(pdev,
- IORESOURCE_MEM));
+ pci_release_selected_regions(pdev,
+ pci_select_bars(pdev, IORESOURCE_MEM));
err_pci_reg:
err_dma:
pci_disable_device(pdev);
@@ -1723,11 +1719,12 @@
dev_info(&pdev->dev, "IOV Disabled\n");
}
#endif
+
iounmap(hw->hw_addr);
if (hw->flash_address)
iounmap(hw->flash_address);
- pci_release_selected_regions(pdev, pci_select_bars(pdev,
- IORESOURCE_MEM));
+ pci_release_selected_regions(pdev,
+ pci_select_bars(pdev, IORESOURCE_MEM));
free_netdev(netdev);
@@ -2288,9 +2285,7 @@
*/
rctl |= E1000_RCTL_SECRC;
- /*
- * disable store bad packets and clear size bits.
- */
+ /* disable store bad packets and clear size bits. */
rctl &= ~(E1000_RCTL_SBP | E1000_RCTL_SZ_256);
/* enable LPE to prevent packets larger than max_frame_size */
@@ -2916,7 +2911,8 @@
static void igb_watchdog_task(struct work_struct *work)
{
struct igb_adapter *adapter = container_of(work,
- struct igb_adapter, watchdog_task);
+ struct igb_adapter,
+ watchdog_task);
struct e1000_hw *hw = &adapter->hw;
struct net_device *netdev = adapter->netdev;
struct igb_ring *tx_ring = adapter->tx_ring;
@@ -2935,14 +2931,14 @@
/* Links status message must follow this format */
printk(KERN_INFO "igb: %s NIC Link is Up %d Mbps %s, "
"Flow Control: %s\n",
- netdev->name,
- adapter->link_speed,
- adapter->link_duplex == FULL_DUPLEX ?
+ netdev->name,
+ adapter->link_speed,
+ adapter->link_duplex == FULL_DUPLEX ?
"Full Duplex" : "Half Duplex",
- ((ctrl & E1000_CTRL_TFCE) && (ctrl &
- E1000_CTRL_RFCE)) ? "RX/TX" : ((ctrl &
- E1000_CTRL_RFCE) ? "RX" : ((ctrl &
- E1000_CTRL_TFCE) ? "TX" : "None")));
+ ((ctrl & E1000_CTRL_TFCE) &&
+ (ctrl & E1000_CTRL_RFCE)) ? "RX/TX" :
+ ((ctrl & E1000_CTRL_RFCE) ? "RX" :
+ ((ctrl & E1000_CTRL_TFCE) ? "TX" : "None")));
/* tweak tx_queue_len according to speed/duplex and
* adjust the timeout factor */
@@ -3724,6 +3720,7 @@
/* igb_down has a dependency on max_frame_size */
adapter->max_frame_size = max_frame;
+
/* NOTE: netdev_alloc_skb reserves 16 bytes, and typically NET_IP_ALIGN
* means we reserve 2 more, this pushes us to allocate from the next
* larger slab size.