bnx2x: Support loading cnic resources at run-time
This patch replaces the BCM_CNIC define with a flag which can change at run-time
and which does not use the CONFIG_CNIC kconfig option.
For the PF/hypervisor driver cnic is always supported, however allocation of
cnic resources and configuration of the HW for offload mode is done only when
the cnic module registers bnx2x.
Signed-off-by: Merav Sicron <meravs@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_reg.h b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_reg.h
index 1b1999d..7d93adb 100644
--- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_reg.h
+++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_reg.h
@@ -2107,6 +2107,7 @@
#define NIG_REG_LLH1_ERROR_MASK 0x10090
/* [RW 8] event id for llh1 */
#define NIG_REG_LLH1_EVENT_ID 0x10088
+#define NIG_REG_LLH1_FUNC_EN 0x16104
#define NIG_REG_LLH1_FUNC_MEM 0x161c0
#define NIG_REG_LLH1_FUNC_MEM_ENABLE 0x16160
#define NIG_REG_LLH1_FUNC_MEM_SIZE 16
@@ -2302,6 +2303,15 @@
* set to 0x345678021. This is a new register (with 2_) added in E3 B0 to
* accommodate the 9 input clients to ETS arbiter. */
#define NIG_REG_P0_TX_ARB_PRIORITY_CLIENT2_MSB 0x18684
+/* [RW 1] MCP-to-host path enable. Set this bit to enable the routing of MCP
+ * packets to BRB LB interface to forward the packet to the host. All
+ * packets from MCP are forwarded to the network when this bit is cleared -
+ * regardless of the configured destination in tx_mng_destination register.
+ * When MCP-to-host paths for both ports 0 and 1 are disabled - the arbiter
+ * for BRB LB interface is bypassed and PBF LB traffic is always selected to
+ * send to BRB LB.
+ */
+#define NIG_REG_P0_TX_MNG_HOST_ENABLE 0x182f4
#define NIG_REG_P1_HWPFC_ENABLE 0x181d0
#define NIG_REG_P1_MAC_IN_EN 0x185c0
/* [RW 1] Output enable for TX MAC interface */
@@ -2418,6 +2428,12 @@
#define NIG_REG_P1_TX_ARB_PRIORITY_CLIENT2_MSB 0x186e4
/* [R 1] TX FIFO for transmitting data to MAC is empty. */
#define NIG_REG_P1_TX_MACFIFO_EMPTY 0x18594
+/* [RW 1] MCP-to-host path enable. Set this bit to enable the routing of MCP
+ * packets to BRB LB interface to forward the packet to the host. All
+ * packets from MCP are forwarded to the network when this bit is cleared -
+ * regardless of the configured destination in tx_mng_destination register.
+ */
+#define NIG_REG_P1_TX_MNG_HOST_ENABLE 0x182f8
/* [R 1] FIFO empty status of the MCP TX FIFO used for storing MCP packets
forwarded to the host. */
#define NIG_REG_P1_TX_MNG_HOST_FIFO_EMPTY 0x182b8