V4L/DVB: IR/lirc: make lirc userspace and staging modules buildable
The lirc userspace needs all the current ioctls defined, and we need to
put the header files in places out-of-tree and/or staging lirc drivers
(which I plan to prep soon) can easily build with. I've actually tested this
in a tree w/all the lirc drivers queued up to be submitted for staging. I'm
also reasonably sure that Andy Walls is going to need most of the ioctls
anyway for his cx23888 IR driver work.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
diff --git a/include/media/lirc.h b/include/media/lirc.h
index 8dffd4f..42c467c 100644
--- a/include/media/lirc.h
+++ b/include/media/lirc.h
@@ -1,6 +1,6 @@
/*
* lirc.h - linux infrared remote control header file
- * last modified 2010/06/03 by Jarod Wilson
+ * last modified 2010/07/13 by Jarod Wilson
*/
#ifndef _LINUX_LIRC_H
@@ -33,6 +33,9 @@
#define LIRC_IS_FREQUENCY(val) (LIRC_MODE2(val) == LIRC_MODE2_FREQUENCY)
#define LIRC_IS_TIMEOUT(val) (LIRC_MODE2(val) == LIRC_MODE2_TIMEOUT)
+/* used heavily by lirc userspace */
+#define lirc_t int
+
/*** lirc compatible hardware features ***/
#define LIRC_MODE2SEND(x) (x)
@@ -95,12 +98,10 @@
#define LIRC_GET_MIN_TIMEOUT _IOR('i', 0x00000008, __u32)
#define LIRC_GET_MAX_TIMEOUT _IOR('i', 0x00000009, __u32)
-#if 0 /* these ioctls are not used at the moment */
#define LIRC_GET_MIN_FILTER_PULSE _IOR('i', 0x0000000a, __u32)
#define LIRC_GET_MAX_FILTER_PULSE _IOR('i', 0x0000000b, __u32)
#define LIRC_GET_MIN_FILTER_SPACE _IOR('i', 0x0000000c, __u32)
#define LIRC_GET_MAX_FILTER_SPACE _IOR('i', 0x0000000d, __u32)
-#endif
/* code length in bits, currently only for LIRC_MODE_LIRCCODE */
#define LIRC_GET_LENGTH _IOR('i', 0x0000000f, __u32)
@@ -121,23 +122,30 @@
*/
#define LIRC_SET_REC_TIMEOUT _IOW('i', 0x00000018, __u32)
-#if 0 /* these ioctls are not used at the moment */
+/* 1 enables, 0 disables timeout reports in MODE2 */
+#define LIRC_SET_REC_TIMEOUT_REPORTS _IOW('i', 0x00000019, __u32)
+
/*
* pulses shorter than this are filtered out by hardware (software
* emulation in lirc_dev?)
*/
-#define LIRC_SET_REC_FILTER_PULSE _IOW('i', 0x00000019, __u32)
+#define LIRC_SET_REC_FILTER_PULSE _IOW('i', 0x0000001a, __u32)
/*
* spaces shorter than this are filtered out by hardware (software
* emulation in lirc_dev?)
*/
-#define LIRC_SET_REC_FILTER_SPACE _IOW('i', 0x0000001a, __u32)
+#define LIRC_SET_REC_FILTER_SPACE _IOW('i', 0x0000001b, __u32)
/*
* if filter cannot be set independantly for pulse/space, this should
* be used
*/
-#define LIRC_SET_REC_FILTER _IOW('i', 0x0000001b, __u32)
-#endif
+#define LIRC_SET_REC_FILTER _IOW('i', 0x0000001c, __u32)
+
+/*
+ * if enabled from the next key press on the driver will send
+ * LIRC_MODE2_FREQUENCY packets
+ */
+#define LIRC_SET_MEASURE_CARRIER_MODE _IOW('i', 0x0000001d, __u32)
/*
* to set a range use
@@ -151,13 +159,7 @@
#define LIRC_NOTIFY_DECODE _IO('i', 0x00000020)
-#if 0 /* these ioctls are not used at the moment */
-/*
- * from the next key press on the driver will send
- * LIRC_MODE2_FREQUENCY packets
- */
-#define LIRC_MEASURE_CARRIER_ENABLE _IO('i', 0x00000021)
-#define LIRC_MEASURE_CARRIER_DISABLE _IO('i', 0x00000022)
-#endif
+#define LIRC_SETUP_START _IO('i', 0x00000021)
+#define LIRC_SETUP_END _IO('i', 0x00000022)
#endif