igb: Add new feature Media Auto Sense for 82580 devices only
This patch adds support for the hardware feature Media Auto Sense. This
feature requires a custom EEPROM image provided by our customer support
team. The feature allows hardware designed with dual PHY's, fiber and
copper to be used with either media without additional EEPROM changes.
Fiber is preferred and driver will swap and configure for fiber media if
sensed by the device at any time. Device will swap back to copper if it
is the only media detected.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
diff --git a/drivers/net/ethernet/intel/igb/e1000_82575.c b/drivers/net/ethernet/intel/igb/e1000_82575.c
index fe9db48..06df692 100644
--- a/drivers/net/ethernet/intel/igb/e1000_82575.c
+++ b/drivers/net/ethernet/intel/igb/e1000_82575.c
@@ -441,6 +441,19 @@
? igb_setup_copper_link_82575
: igb_setup_serdes_link_82575;
+ if (mac->type == e1000_82580) {
+ switch (hw->device_id) {
+ /* feature not supported on these id's */
+ case E1000_DEV_ID_DH89XXCC_SGMII:
+ case E1000_DEV_ID_DH89XXCC_SERDES:
+ case E1000_DEV_ID_DH89XXCC_BACKPLANE:
+ case E1000_DEV_ID_DH89XXCC_SFP:
+ break;
+ default:
+ hw->dev_spec._82575.mas_capable = true;
+ break;
+ }
+ }
return 0;
}
diff --git a/drivers/net/ethernet/intel/igb/e1000_defines.h b/drivers/net/ethernet/intel/igb/e1000_defines.h
index 378ca21..0571b97 100644
--- a/drivers/net/ethernet/intel/igb/e1000_defines.h
+++ b/drivers/net/ethernet/intel/igb/e1000_defines.h
@@ -205,6 +205,11 @@
*/
#define E1000_CONNSW_ENRGSRC 0x4
+#define E1000_CONNSW_PHYSD 0x400
+#define E1000_CONNSW_PHY_PDN 0x800
+#define E1000_CONNSW_SERDESD 0x200
+#define E1000_CONNSW_AUTOSENSE_CONF 0x2
+#define E1000_CONNSW_AUTOSENSE_EN 0x1
#define E1000_PCS_CFG_PCS_EN 8
#define E1000_PCS_LCTL_FLV_LINK_UP 1
#define E1000_PCS_LCTL_FSV_100 2
diff --git a/drivers/net/ethernet/intel/igb/e1000_hw.h b/drivers/net/ethernet/intel/igb/e1000_hw.h
index 5f9758f..ab99e2b 100644
--- a/drivers/net/ethernet/intel/igb/e1000_hw.h
+++ b/drivers/net/ethernet/intel/igb/e1000_hw.h
@@ -535,6 +535,7 @@
bool module_plugged;
u8 media_port;
bool media_changed;
+ bool mas_capable;
};
struct e1000_hw {
diff --git a/drivers/net/ethernet/intel/igb/igb.h b/drivers/net/ethernet/intel/igb/igb.h
index 6c80792..11173f4 100644
--- a/drivers/net/ethernet/intel/igb/igb.h
+++ b/drivers/net/ethernet/intel/igb/igb.h
@@ -450,6 +450,8 @@
u8 rss_indir_tbl[IGB_RETA_SIZE];
unsigned long link_check_timeout;
+ int copper_tries;
+ struct e1000_info ei;
};
#define IGB_FLAG_HAS_MSI (1 << 0)
@@ -463,6 +465,14 @@
#define IGB_FLAG_WOL_SUPPORTED (1 << 8)
#define IGB_FLAG_NEED_LINK_UPDATE (1 << 9)
#define IGB_FLAG_MEDIA_RESET (1 << 10)
+#define IGB_FLAG_MAS_CAPABLE (1 << 11)
+#define IGB_FLAG_MAS_ENABLE (1 << 12)
+
+/* Media Auto Sense */
+#define IGB_MAS_ENABLE_0 0X0001
+#define IGB_MAS_ENABLE_1 0X0002
+#define IGB_MAS_ENABLE_2 0X0004
+#define IGB_MAS_ENABLE_3 0X0008
/* DMA Coalescing defines */
#define IGB_MIN_TXPBSIZE 20408
diff --git a/drivers/net/ethernet/intel/igb/igb_ethtool.c b/drivers/net/ethernet/intel/igb/igb_ethtool.c
index c3143da..1c7d238 100644
--- a/drivers/net/ethernet/intel/igb/igb_ethtool.c
+++ b/drivers/net/ethernet/intel/igb/igb_ethtool.c
@@ -1983,6 +1983,10 @@
bool if_running = netif_running(netdev);
set_bit(__IGB_TESTING, &adapter->state);
+
+ /* can't do offline tests on media switching devices */
+ if (adapter->hw.dev_spec._82575.mas_capable)
+ eth_test->flags &= ~ETH_TEST_FL_OFFLINE;
if (eth_test->flags == ETH_TEST_FL_OFFLINE) {
/* Offline tests */
diff --git a/drivers/net/ethernet/intel/igb/igb_main.c b/drivers/net/ethernet/intel/igb/igb_main.c
index ed129f1..3bc10bd 100644
--- a/drivers/net/ethernet/intel/igb/igb_main.c
+++ b/drivers/net/ethernet/intel/igb/igb_main.c
@@ -1607,6 +1607,73 @@
}
/**
+ * Detect and switch function for Media Auto Sense
+ * @adapter: address of the board private structure
+ **/
+static void igb_check_swap_media(struct igb_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ u32 ctrl_ext, connsw;
+ bool swap_now = false;
+
+ ctrl_ext = rd32(E1000_CTRL_EXT);
+ connsw = rd32(E1000_CONNSW);
+
+ /* need to live swap if current media is copper and we have fiber/serdes
+ * to go to.
+ */
+
+ if ((hw->phy.media_type == e1000_media_type_copper) &&
+ (!(connsw & E1000_CONNSW_AUTOSENSE_EN))) {
+ swap_now = true;
+ } else if (!(connsw & E1000_CONNSW_SERDESD)) {
+ /* copper signal takes time to appear */
+ if (adapter->copper_tries < 4) {
+ adapter->copper_tries++;
+ connsw |= E1000_CONNSW_AUTOSENSE_CONF;
+ wr32(E1000_CONNSW, connsw);
+ return;
+ } else {
+ adapter->copper_tries = 0;
+ if ((connsw & E1000_CONNSW_PHYSD) &&
+ (!(connsw & E1000_CONNSW_PHY_PDN))) {
+ swap_now = true;
+ connsw &= ~E1000_CONNSW_AUTOSENSE_CONF;
+ wr32(E1000_CONNSW, connsw);
+ }
+ }
+ }
+
+ if (!swap_now)
+ return;
+
+ switch (hw->phy.media_type) {
+ case e1000_media_type_copper:
+ netdev_info(adapter->netdev,
+ "MAS: changing media to fiber/serdes\n");
+ ctrl_ext |=
+ E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES;
+ adapter->flags |= IGB_FLAG_MEDIA_RESET;
+ adapter->copper_tries = 0;
+ break;
+ case e1000_media_type_internal_serdes:
+ case e1000_media_type_fiber:
+ netdev_info(adapter->netdev,
+ "MAS: changing media to copper\n");
+ ctrl_ext &=
+ ~E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES;
+ adapter->flags |= IGB_FLAG_MEDIA_RESET;
+ break;
+ default:
+ /* shouldn't get here during regular operation */
+ netdev_err(adapter->netdev,
+ "AMS: Invalid media type found, returning\n");
+ break;
+ }
+ wr32(E1000_CTRL_EXT, ctrl_ext);
+}
+
+/**
* igb_up - Open the interface and prepare it to handle traffic
* @adapter: board private structure
**/
@@ -1719,6 +1786,37 @@
clear_bit(__IGB_RESETTING, &adapter->state);
}
+/** igb_enable_mas - Media Autosense re-enable after swap
+ *
+ * @adapter: adapter struct
+ **/
+static s32 igb_enable_mas(struct igb_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ u32 connsw;
+ s32 ret_val = 0;
+
+ connsw = rd32(E1000_CONNSW);
+ if (!(hw->phy.media_type == e1000_media_type_copper))
+ return ret_val;
+
+ /* configure for SerDes media detect */
+ if (!(connsw & E1000_CONNSW_SERDESD)) {
+ connsw |= E1000_CONNSW_ENRGSRC;
+ connsw |= E1000_CONNSW_AUTOSENSE_EN;
+ wr32(E1000_CONNSW, connsw);
+ wrfl();
+ } else if (connsw & E1000_CONNSW_SERDESD) {
+ /* already SerDes, no need to enable anything */
+ return ret_val;
+ } else {
+ netdev_info(adapter->netdev,
+ "MAS: Unable to configure feature, disabling..\n");
+ adapter->flags &= ~IGB_FLAG_MAS_ENABLE;
+ }
+ return ret_val;
+}
+
void igb_reset(struct igb_adapter *adapter)
{
struct pci_dev *pdev = adapter->pdev;
@@ -1830,6 +1928,16 @@
hw->mac.ops.reset_hw(hw);
wr32(E1000_WUC, 0);
+ if (adapter->flags & IGB_FLAG_MEDIA_RESET) {
+ /* need to resetup here after media swap */
+ adapter->ei.get_invariants(hw);
+ adapter->flags &= ~IGB_FLAG_MEDIA_RESET;
+ }
+ if (adapter->flags & IGB_FLAG_MAS_ENABLE) {
+ if (igb_enable_mas(adapter))
+ dev_err(&pdev->dev,
+ "Error enabling Media Auto Sense\n");
+ }
if (hw->mac.ops.init_hw(hw))
dev_err(&pdev->dev, "Hardware Error\n");
@@ -1976,6 +2084,58 @@
}
/**
+ * igb_init_mas - init Media Autosense feature if enabled in the NVM
+ *
+ * @adapter: adapter struct
+ **/
+static void igb_init_mas(struct igb_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ u16 eeprom_data;
+
+ hw->nvm.ops.read(hw, NVM_COMPAT, 1, &eeprom_data);
+ switch (hw->bus.func) {
+ case E1000_FUNC_0:
+ if (eeprom_data & IGB_MAS_ENABLE_0) {
+ adapter->flags |= IGB_FLAG_MAS_ENABLE;
+ netdev_info(adapter->netdev,
+ "MAS: Enabling Media Autosense for port %d\n",
+ hw->bus.func);
+ }
+ break;
+ case E1000_FUNC_1:
+ if (eeprom_data & IGB_MAS_ENABLE_1) {
+ adapter->flags |= IGB_FLAG_MAS_ENABLE;
+ netdev_info(adapter->netdev,
+ "MAS: Enabling Media Autosense for port %d\n",
+ hw->bus.func);
+ }
+ break;
+ case E1000_FUNC_2:
+ if (eeprom_data & IGB_MAS_ENABLE_2) {
+ adapter->flags |= IGB_FLAG_MAS_ENABLE;
+ netdev_info(adapter->netdev,
+ "MAS: Enabling Media Autosense for port %d\n",
+ hw->bus.func);
+ }
+ break;
+ case E1000_FUNC_3:
+ if (eeprom_data & IGB_MAS_ENABLE_3) {
+ adapter->flags |= IGB_FLAG_MAS_ENABLE;
+ netdev_info(adapter->netdev,
+ "MAS: Enabling Media Autosense for port %d\n",
+ hw->bus.func);
+ }
+ break;
+ default:
+ /* Shouldn't get here */
+ netdev_err(adapter->netdev,
+ "MAS: Invalid port configuration, returning\n");
+ break;
+ }
+}
+
+/**
* igb_init_i2c - Init I2C interface
* @adapter: pointer to adapter structure
**/
@@ -2346,6 +2506,11 @@
adapter->ets = false;
}
#endif
+ /* Check if Media Autosense is enabled */
+ adapter->ei = *ei;
+ if (hw->dev_spec._82575.mas_capable)
+ igb_init_mas(adapter);
+
/* do hw tstamp init after resetting */
igb_ptp_init(adapter);
@@ -3931,6 +4096,7 @@
struct net_device *netdev = adapter->netdev;
u32 link;
int i;
+ u32 connsw;
link = igb_has_link(adapter);
@@ -3941,6 +4107,14 @@
link = false;
}
+ /* Force link down if we have fiber to swap to */
+ if (adapter->flags & IGB_FLAG_MAS_ENABLE) {
+ if (hw->phy.media_type == e1000_media_type_copper) {
+ connsw = rd32(E1000_CONNSW);
+ if (!(connsw & E1000_CONNSW_AUTOSENSE_EN))
+ link = 0;
+ }
+ }
if (link) {
/* Perform a reset if the media type changed. */
if (hw->dev_spec._82575.media_changed) {
@@ -4028,8 +4202,27 @@
mod_timer(&adapter->phy_info_timer,
round_jiffies(jiffies + 2 * HZ));
+ /* link is down, time to check for alternate media */
+ if (adapter->flags & IGB_FLAG_MAS_ENABLE) {
+ igb_check_swap_media(adapter);
+ if (adapter->flags & IGB_FLAG_MEDIA_RESET) {
+ schedule_work(&adapter->reset_task);
+ /* return immediately */
+ return;
+ }
+ }
pm_schedule_suspend(netdev->dev.parent,
MSEC_PER_SEC * 5);
+
+ /* also check for alternate media here */
+ } else if (!netif_carrier_ok(netdev) &&
+ (adapter->flags & IGB_FLAG_MAS_ENABLE)) {
+ igb_check_swap_media(adapter);
+ if (adapter->flags & IGB_FLAG_MEDIA_RESET) {
+ schedule_work(&adapter->reset_task);
+ /* return immediately */
+ return;
+ }
}
}