[SCSI] lpfc 8.2.3 : Added support for ASICs that report temperature
Added support for ASICs that report temperature. Temperature notices are
reported as events and logged. Temperature can be read via sysfs.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
diff --git a/drivers/scsi/lpfc/lpfc_init.c b/drivers/scsi/lpfc/lpfc_init.c
index ecebdfa..17f4454 100644
--- a/drivers/scsi/lpfc/lpfc_init.c
+++ b/drivers/scsi/lpfc/lpfc_init.c
@@ -212,6 +212,18 @@
return 0;
}
+/* Completion handler for config async event mailbox command. */
+static void
+lpfc_config_async_cmpl(struct lpfc_hba * phba, LPFC_MBOXQ_t * pmboxq)
+{
+ if (pmboxq->mb.mbxStatus == MBX_SUCCESS)
+ phba->temp_sensor_support = 1;
+ else
+ phba->temp_sensor_support = 0;
+ mempool_free(pmboxq, phba->mbox_mem_pool);
+ return;
+}
+
/************************************************************************/
/* */
/* lpfc_config_port_post */
@@ -409,7 +421,21 @@
return -EIO;
}
/* MBOX buffer will be freed in mbox compl */
+ pmb = mempool_alloc(phba->mbox_mem_pool, GFP_KERNEL);
+ lpfc_config_async(phba, pmb, LPFC_ELS_RING);
+ pmb->mbox_cmpl = lpfc_config_async_cmpl;
+ pmb->vport = phba->pport;
+ rc = lpfc_sli_issue_mbox(phba, pmb, MBX_NOWAIT);
+ if ((rc != MBX_BUSY) && (rc != MBX_SUCCESS)) {
+ lpfc_printf_log(phba,
+ KERN_ERR,
+ LOG_INIT,
+ "0456 Adapter failed to issue "
+ "ASYNCEVT_ENABLE mbox status x%x \n.",
+ rc);
+ mempool_free(pmb, phba->mbox_mem_pool);
+ }
return (0);
}
@@ -601,6 +627,8 @@
struct lpfc_sli_ring *pring;
struct lpfc_vport **vports;
uint32_t event_data;
+ unsigned long temperature;
+ struct temp_event temp_event_data;
struct Scsi_Host *shost;
int i;
@@ -655,6 +683,33 @@
return;
}
lpfc_unblock_mgmt_io(phba);
+ } else if (phba->work_hs & HS_CRIT_TEMP) {
+ temperature = readl(phba->MBslimaddr + TEMPERATURE_OFFSET);
+ temp_event_data.event_type = FC_REG_TEMPERATURE_EVENT;
+ temp_event_data.event_code = LPFC_CRIT_TEMP;
+ temp_event_data.data = (uint32_t)temperature;
+
+ lpfc_printf_log(phba, KERN_ERR, LOG_INIT,
+ "0459 Adapter maximum temperature exceeded "
+ "(%ld), taking this port offline "
+ "Data: x%x x%x x%x\n",
+ temperature, phba->work_hs,
+ phba->work_status[0], phba->work_status[1]);
+
+ shost = lpfc_shost_from_vport(phba->pport);
+ fc_host_post_vendor_event(shost, fc_get_event_number(),
+ sizeof(temp_event_data),
+ (char *) &temp_event_data,
+ SCSI_NL_VID_TYPE_PCI
+ | PCI_VENDOR_ID_EMULEX);
+
+ psli->sli_flag &= ~LPFC_SLI2_ACTIVE;
+ lpfc_offline_prep(phba);
+ lpfc_offline(phba);
+ lpfc_unblock_mgmt_io(phba);
+ phba->link_state = LPFC_HBA_ERROR;
+ lpfc_hba_down_post(phba);
+
} else {
/* The if clause above forces this code path when the status
* failure is a value other than FFER6. Do not call the offline