staging: comedi: s626: #if 0 out the "SAA7146 BUG WORKAROUND"
Until it's determined if this workaround can be removed, block
out the code with an #if 0/#endif and remove the individual
comments on each line.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
diff --git a/drivers/staging/comedi/drivers/s626.c b/drivers/staging/comedi/drivers/s626.c
index cd09c37..4315892 100644
--- a/drivers/staging/comedi/drivers/s626.c
+++ b/drivers/staging/comedi/drivers/s626.c
@@ -2459,16 +2459,10 @@
static void s626_initialize(struct comedi_device *dev)
{
-/* uint8_t PollList; */
-/* uint16_t AdcData; */
-/* uint16_t StartVal; */
-/* uint16_t index; */
-/* unsigned int data[16]; */
dma_addr_t pPhysBuf;
uint16_t chan;
int i;
-
/* enab DEBI and audio pins, enable I2C interface. */
MC_ENABLE(P_MC1, MC1_DEBI | MC1_AUDIO | MC1_I2C);
/* Configure DEBI operating mode. */
@@ -2568,38 +2562,50 @@
/* RPS program performs no explicit mem writes. */
WR7146(P_RPS1_TOUT, 0); /* Disable RPS timeouts. */
- /* SAA7146 BUG WORKAROUND. Initialize SAA7146 ADC interface
- * to a known state by invoking ADCs until FB BUFFER 1
- * register shows that it is correctly receiving ADC data.
- * This is necessary because the SAA7146 ADC interface does
- * not start up in a defined state after a PCI reset.
+#if 0
+ /*
+ * SAA7146 BUG WORKAROUND
+ *
+ * Initialize SAA7146 ADC interface to a known state by
+ * invoking ADCs until FB BUFFER 1 register shows that it
+ * is correctly receiving ADC data. This is necessary
+ * because the SAA7146 ADC interface does not start up in
+ * a defined state after a PCI reset.
*/
-/* PollList = EOPL; // Create a simple polling */
-/* // list for analog input */
-/* // channel 0. */
-/* ResetADC( dev, &PollList ); */
+ {
+ uint8_t PollList;
+ uint16_t AdcData;
+ uint16_t StartVal;
+ uint16_t index;
+ unsigned int data[16];
-/* s626_ai_rinsn(dev,dev->subdevices,NULL,data); //( &AdcData ); // */
-/* //Get initial ADC */
-/* //value. */
+ /* Create a simple polling list for analog input channel 0 */
+ PollList = EOPL;
+ ResetADC(dev, &PollList);
-/* StartVal = data[0]; */
+ /* Get initial ADC value */
+ s626_ai_rinsn(dev, dev->subdevices, NULL, data);
+ StartVal = data[0];
-/* // VERSION 2.01 CHANGE: TIMEOUT ADDED TO PREVENT HANGED EXECUTION. */
-/* // Invoke ADCs until the new ADC value differs from the initial */
-/* // value or a timeout occurs. The timeout protects against the */
-/* // possibility that the driver is restarting and the ADC data is a */
-/* // fixed value resulting from the applied ADC analog input being */
-/* // unusually quiet or at the rail. */
+ /*
+ * VERSION 2.01 CHANGE: TIMEOUT ADDED TO PREVENT HANGED EXECUTION.
+ *
+ * Invoke ADCs until the new ADC value differs from the initial
+ * value or a timeout occurs. The timeout protects against the
+ * possibility that the driver is restarting and the ADC data is a
+ * fixed value resulting from the applied ADC analog input being
+ * unusually quiet or at the rail.
+ */
+ for (index = 0; index < 500; index++) {
+ s626_ai_rinsn(dev, dev->subdevices, NULL, data);
+ AdcData = data[0];
+ if (AdcData != StartVal)
+ break;
+ }
-/* for ( index = 0; index < 500; index++ ) */
-/* { */
-/* s626_ai_rinsn(dev,dev->subdevices,NULL,data); */
-/* AdcData = data[0]; //ReadADC( &AdcData ); */
-/* if ( AdcData != StartVal ) */
-/* break; */
-/* } */
+ }
+#endif /* SAA7146 BUG WORKAROUND */
/* end initADC */