dmaengine: qcom: bam_dma: rename BAM_MAX_DATA_SIZE define

It seems that the define has not been with acurate name and
makes confusion while reading the code. The more acurate
name should be BAM_FIFO_SIZE.

Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
diff --git a/drivers/dma/qcom/bam_dma.c b/drivers/dma/qcom/bam_dma.c
index 7e5ad1c..969b481 100644
--- a/drivers/dma/qcom/bam_dma.c
+++ b/drivers/dma/qcom/bam_dma.c
@@ -342,7 +342,7 @@
 
 #define BAM_DESC_FIFO_SIZE	SZ_32K
 #define MAX_DESCRIPTORS (BAM_DESC_FIFO_SIZE / sizeof(struct bam_desc_hw) - 1)
-#define BAM_MAX_DATA_SIZE	(SZ_32K - 8)
+#define BAM_FIFO_SIZE	(SZ_32K - 8)
 
 struct bam_chan {
 	struct virt_dma_chan vc;
@@ -459,7 +459,7 @@
 	 */
 	writel_relaxed(ALIGN(bchan->fifo_phys, sizeof(struct bam_desc_hw)),
 			bam_addr(bdev, bchan->id, BAM_P_DESC_FIFO_ADDR));
-	writel_relaxed(BAM_MAX_DATA_SIZE,
+	writel_relaxed(BAM_FIFO_SIZE,
 			bam_addr(bdev, bchan->id, BAM_P_FIFO_SIZES));
 
 	/* enable the per pipe interrupts, enable EOT, ERR, and INT irqs */
@@ -605,7 +605,7 @@
 
 	/* calculate number of required entries */
 	for_each_sg(sgl, sg, sg_len, i)
-		num_alloc += DIV_ROUND_UP(sg_dma_len(sg), BAM_MAX_DATA_SIZE);
+		num_alloc += DIV_ROUND_UP(sg_dma_len(sg), BAM_FIFO_SIZE);
 
 	/* allocate enough room to accomodate the number of entries */
 	async_desc = kzalloc(sizeof(*async_desc) +
@@ -636,10 +636,10 @@
 			desc->addr = cpu_to_le32(sg_dma_address(sg) +
 						 curr_offset);
 
-			if (remainder > BAM_MAX_DATA_SIZE) {
-				desc->size = cpu_to_le16(BAM_MAX_DATA_SIZE);
-				remainder -= BAM_MAX_DATA_SIZE;
-				curr_offset += BAM_MAX_DATA_SIZE;
+			if (remainder > BAM_FIFO_SIZE) {
+				desc->size = cpu_to_le16(BAM_FIFO_SIZE);
+				remainder -= BAM_FIFO_SIZE;
+				curr_offset += BAM_FIFO_SIZE;
 			} else {
 				desc->size = cpu_to_le16(remainder);
 				remainder = 0;
@@ -1174,7 +1174,7 @@
 	/* set max dma segment size */
 	bdev->common.dev = bdev->dev;
 	bdev->common.dev->dma_parms = &bdev->dma_parms;
-	ret = dma_set_max_seg_size(bdev->common.dev, BAM_MAX_DATA_SIZE);
+	ret = dma_set_max_seg_size(bdev->common.dev, BAM_FIFO_SIZE);
 	if (ret) {
 		dev_err(bdev->dev, "cannot set maximum segment size\n");
 		goto err_bam_channel_exit;