Gitiles
Code Review Sign In
gerrit-public.fairphone.software / kernel / msm-4.9 / 5b9ab2ec04ec1e1e53939768805612ac191d7ba2 / . / drivers / net / wireless / iwlwifi / iwl-agn.c
blob: 7888250117dc52f48553f4daf018fa85e386facf [file] [log] [blame]
/******************************************************************************
*
* Copyright(c) 2003 - 2008 Intel Corporation. All rights reserved.
*
* Portions of this file are derived from the ipw3945 project, as well
* as portions of the ieee80211 subsystem header files.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of version 2 of the GNU General Public License as
* published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful, but WITHOUT
* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
* FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
* more details.
*
* You should have received a copy of the GNU General Public License along with
* this program; if not, write to the Free Software Foundation, Inc.,
* 51 Franklin Street, Fifth Floor, Boston, MA 02110, USA
*
* The full GNU General Public License is included in this distribution in the
* file called LICENSE.
*
* Contact Information:
* James P. Ketrenos <ipw2100-admin@linux.intel.com>
* Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
*
*****************************************************************************/
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/init.h>
#include <linux/pci.h>
#include <linux/dma-mapping.h>
#include <linux/delay.h>
#include <linux/skbuff.h>
#include <linux/netdevice.h>
#include <linux/wireless.h>
#include <linux/firmware.h>
#include <linux/etherdevice.h>
#include <linux/if_arp.h>
#include <net/mac80211.h>
#include <asm/div64.h>
#include "iwl-eeprom.h"
#include "iwl-dev.h"
#include "iwl-core.h"
#include "iwl-io.h"
#include "iwl-helpers.h"
#include "iwl-sta.h"
#include "iwl-calib.h"
/******************************************************************************
*
* module boiler plate
*
******************************************************************************/
/*
* module name, copyright, version, etc.
* NOTE: DRV_NAME is defined in iwlwifi.h for use by iwl-debug.h and printk
*/
#define DRV_DESCRIPTION "Intel(R) Wireless WiFi Link AGN driver for Linux"
#ifdef CONFIG_IWLWIFI_DEBUG
#define VD "d"
#else
#define VD
#endif
#ifdef CONFIG_IWLAGN_SPECTRUM_MEASUREMENT
#define VS "s"
#else
#define VS
#endif
#define DRV_VERSION IWLWIFI_VERSION VD VS
MODULE_DESCRIPTION(DRV_DESCRIPTION);
MODULE_VERSION(DRV_VERSION);
MODULE_AUTHOR(DRV_COPYRIGHT);
MODULE_LICENSE("GPL");
MODULE_ALIAS("iwl4965");
/*************** STATION TABLE MANAGEMENT ****
* mac80211 should be examined to determine if sta_info is duplicating
* the functionality provided here
*/
/**************************************************************/
static void iwl_set_rxon_hwcrypto(struct iwl_priv *priv, int hw_decrypt)
{
struct iwl_rxon_cmd *rxon = &priv->staging_rxon;
if (hw_decrypt)
rxon->filter_flags &= ~RXON_FILTER_DIS_DECRYPT_MSK;
else
rxon->filter_flags |= RXON_FILTER_DIS_DECRYPT_MSK;
}
/**
* iwl_check_rxon_cmd - validate RXON structure is valid
*
* NOTE: This is really only useful during development and can eventually
* be #ifdef'd out once the driver is stable and folks aren't actively
* making changes
*/
static int iwl_check_rxon_cmd(struct iwl_rxon_cmd *rxon)
{
int error = 0;
int counter = 1;
if (rxon->flags & RXON_FLG_BAND_24G_MSK) {
error |= le32_to_cpu(rxon->flags &
(RXON_FLG_TGJ_NARROW_BAND_MSK |
RXON_FLG_RADAR_DETECT_MSK));
if (error)
IWL_WARNING("check 24G fields %d | %d\n",
counter++, error);
} else {
error |= (rxon->flags & RXON_FLG_SHORT_SLOT_MSK) ?
0 : le32_to_cpu(RXON_FLG_SHORT_SLOT_MSK);
if (error)
IWL_WARNING("check 52 fields %d | %d\n",
counter++, error);
error |= le32_to_cpu(rxon->flags & RXON_FLG_CCK_MSK);
if (error)
IWL_WARNING("check 52 CCK %d | %d\n",
counter++, error);
}
error |= (rxon->node_addr[0] | rxon->bssid_addr[0]) & 0x1;
if (error)
IWL_WARNING("check mac addr %d | %d\n", counter++, error);
/* make sure basic rates 6Mbps and 1Mbps are supported */
error |= (((rxon->ofdm_basic_rates & IWL_RATE_6M_MASK) == 0) &&
((rxon->cck_basic_rates & IWL_RATE_1M_MASK) == 0));
if (error)
IWL_WARNING("check basic rate %d | %d\n", counter++, error);
error |= (le16_to_cpu(rxon->assoc_id) > 2007);
if (error)
IWL_WARNING("check assoc id %d | %d\n", counter++, error);
error |= ((rxon->flags & (RXON_FLG_CCK_MSK | RXON_FLG_SHORT_SLOT_MSK))
== (RXON_FLG_CCK_MSK | RXON_FLG_SHORT_SLOT_MSK));
if (error)
IWL_WARNING("check CCK and short slot %d | %d\n",
counter++, error);
error |= ((rxon->flags & (RXON_FLG_CCK_MSK | RXON_FLG_AUTO_DETECT_MSK))
== (RXON_FLG_CCK_MSK | RXON_FLG_AUTO_DETECT_MSK));
if (error)
IWL_WARNING("check CCK & auto detect %d | %d\n",
counter++, error);
error |= ((rxon->flags & (RXON_FLG_AUTO_DETECT_MSK |
RXON_FLG_TGG_PROTECT_MSK)) == RXON_FLG_TGG_PROTECT_MSK);
if (error)
IWL_WARNING("check TGG and auto detect %d | %d\n",
counter++, error);
if (error)
IWL_WARNING("Tuning to channel %d\n",
le16_to_cpu(rxon->channel));
if (error) {
IWL_ERROR("Not a valid iwl_rxon_assoc_cmd field values\n");
return -1;
}
return 0;
}
/**
* iwl_full_rxon_required - check if full RXON (vs RXON_ASSOC) cmd is needed
* @priv: staging_rxon is compared to active_rxon
*
* If the RXON structure is changing enough to require a new tune,
* or is clearing the RXON_FILTER_ASSOC_MSK, then return 1 to indicate that
* a new tune (full RXON command, rather than RXON_ASSOC cmd) is required.
*/
static int iwl_full_rxon_required(struct iwl_priv *priv)
{
/* These items are only settable from the full RXON command */
if (!(iwl_is_associated(priv)) ||
compare_ether_addr(priv->staging_rxon.bssid_addr,
priv->active_rxon.bssid_addr) ||
compare_ether_addr(priv->staging_rxon.node_addr,
priv->active_rxon.node_addr) ||
compare_ether_addr(priv->staging_rxon.wlap_bssid_addr,
priv->active_rxon.wlap_bssid_addr) ||
(priv->staging_rxon.dev_type != priv->active_rxon.dev_type) ||
(priv->staging_rxon.channel != priv->active_rxon.channel) ||
(priv->staging_rxon.air_propagation !=
priv->active_rxon.air_propagation) ||
(priv->staging_rxon.ofdm_ht_single_stream_basic_rates !=
priv->active_rxon.ofdm_ht_single_stream_basic_rates) ||
(priv->staging_rxon.ofdm_ht_dual_stream_basic_rates !=
priv->active_rxon.ofdm_ht_dual_stream_basic_rates) ||
(priv->staging_rxon.assoc_id != priv->active_rxon.assoc_id))
return 1;
/* flags, filter_flags, ofdm_basic_rates, and cck_basic_rates can
* be updated with the RXON_ASSOC command -- however only some
* flag transitions are allowed using RXON_ASSOC */
/* Check if we are not switching bands */
if ((priv->staging_rxon.flags & RXON_FLG_BAND_24G_MSK) !=
(priv->active_rxon.flags & RXON_FLG_BAND_24G_MSK))
return 1;
/* Check if we are switching association toggle */
if ((priv->staging_rxon.filter_flags & RXON_FILTER_ASSOC_MSK) !=
(priv->active_rxon.filter_flags & RXON_FILTER_ASSOC_MSK))
return 1;
return 0;
}
/**
* iwl_commit_rxon - commit staging_rxon to hardware
*
* The RXON command in staging_rxon is committed to the hardware and
* the active_rxon structure is updated with the new data. This
* function correctly transitions out of the RXON_ASSOC_MSK state if
* a HW tune is required based on the RXON structure changes.
*/
static int iwl_commit_rxon(struct iwl_priv *priv)
{
/* cast away the const for active_rxon in this function */
struct iwl_rxon_cmd *active_rxon = (void *)&priv->active_rxon;
int ret;
bool new_assoc =
!!(priv->staging_rxon.filter_flags & RXON_FILTER_ASSOC_MSK);
if (!iwl_is_alive(priv))
return -EBUSY;
/* always get timestamp with Rx frame */
priv->staging_rxon.flags |= RXON_FLG_TSF2HOST_MSK;
/* allow CTS-to-self if possible. this is relevant only for
* 5000, but will not damage 4965 */
priv->staging_rxon.flags |= RXON_FLG_SELF_CTS_EN;
ret = iwl_check_rxon_cmd(&priv->staging_rxon);
if (ret) {
IWL_ERROR("Invalid RXON configuration. Not committing.\n");
return -EINVAL;
}
/* If we don't need to send a full RXON, we can use
* iwl_rxon_assoc_cmd which is used to reconfigure filter
* and other flags for the current radio configuration. */
if (!iwl_full_rxon_required(priv)) {
ret = iwl_send_rxon_assoc(priv);
if (ret) {
IWL_ERROR("Error setting RXON_ASSOC (%d)\n", ret);
return ret;
}
memcpy(active_rxon, &priv->staging_rxon, sizeof(*active_rxon));
return 0;
}
/* station table will be cleared */
priv->assoc_station_added = 0;
/* If we are currently associated and the new config requires
* an RXON_ASSOC and the new config wants the associated mask enabled,
* we must clear the associated from the active configuration
* before we apply the new config */
if (iwl_is_associated(priv) && new_assoc) {
IWL_DEBUG_INFO("Toggling associated bit on current RXON\n");
active_rxon->filter_flags &= ~RXON_FILTER_ASSOC_MSK;
ret = iwl_send_cmd_pdu(priv, REPLY_RXON,
sizeof(struct iwl_rxon_cmd),
&priv->active_rxon);
/* If the mask clearing failed then we set
* active_rxon back to what it was previously */
if (ret) {
active_rxon->filter_flags |= RXON_FILTER_ASSOC_MSK;
IWL_ERROR("Error clearing ASSOC_MSK (%d)\n", ret);
return ret;
}
}
IWL_DEBUG_INFO("Sending RXON\n"
"* with%s RXON_FILTER_ASSOC_MSK\n"
"* channel = %d\n"
"* bssid = %pM\n",
(new_assoc ? "" : "out"),
le16_to_cpu(priv->staging_rxon.channel),
priv->staging_rxon.bssid_addr);
iwl_set_rxon_hwcrypto(priv, !priv->hw_params.sw_crypto);
/* Apply the new configuration
* RXON unassoc clears the station table in uCode, send it before
* we add the bcast station. If assoc bit is set, we will send RXON
* after having added the bcast and bssid station.
*/
if (!new_assoc) {
ret = iwl_send_cmd_pdu(priv, REPLY_RXON,
sizeof(struct iwl_rxon_cmd), &priv->staging_rxon);
if (ret) {
IWL_ERROR("Error setting new RXON (%d)\n", ret);
return ret;
}
memcpy(active_rxon, &priv->staging_rxon, sizeof(*active_rxon));
}
iwl_clear_stations_table(priv);
if (!priv->error_recovering)
priv->start_calib = 0;
/* Add the broadcast address so we can send broadcast frames */
if (iwl_rxon_add_station(priv, iwl_bcast_addr, 0) ==
IWL_INVALID_STATION) {
IWL_ERROR("Error adding BROADCAST address for transmit.\n");
return -EIO;
}
/* If we have set the ASSOC_MSK and we are in BSS mode then
* add the IWL_AP_ID to the station rate table */
if (new_assoc) {
if (priv->iw_mode == NL80211_IFTYPE_STATION) {
ret = iwl_rxon_add_station(priv,
priv->active_rxon.bssid_addr, 1);
if (ret == IWL_INVALID_STATION) {
IWL_ERROR("Error adding AP address for TX.\n");
return -EIO;
}
priv->assoc_station_added = 1;
if (priv->default_wep_key &&
iwl_send_static_wepkey_cmd(priv, 0))
IWL_ERROR("Could not send WEP static key.\n");
}
/* Apply the new configuration
* RXON assoc doesn't clear the station table in uCode,
*/
ret = iwl_send_cmd_pdu(priv, REPLY_RXON,
sizeof(struct iwl_rxon_cmd), &priv->staging_rxon);
if (ret) {
IWL_ERROR("Error setting new RXON (%d)\n", ret);
return ret;
}
memcpy(active_rxon, &priv->staging_rxon, sizeof(*active_rxon));
}
iwl_init_sensitivity(priv);
/* If we issue a new RXON command which required a tune then we must
* send a new TXPOWER command or we won't be able to Tx any frames */
ret = iwl_set_tx_power(priv, priv->tx_power_user_lmt, true);
if (ret) {
IWL_ERROR("Error sending TX power (%d)\n", ret);
return ret;
}
return 0;
}
void iwl_update_chain_flags(struct iwl_priv *priv)
{
iwl_set_rxon_chain(priv);
iwl_commit_rxon(priv);
}
static int iwl_send_bt_config(struct iwl_priv *priv)
{
struct iwl4965_bt_cmd bt_cmd = {
.flags = 3,
.lead_time = 0xAA,
.max_kill = 1,
.kill_ack_mask = 0,
.kill_cts_mask = 0,
};
return iwl_send_cmd_pdu(priv, REPLY_BT_CONFIG,
sizeof(struct iwl4965_bt_cmd), &bt_cmd);
}
static void iwl_clear_free_frames(struct iwl_priv *priv)
{
struct list_head *element;
IWL_DEBUG_INFO("%d frames on pre-allocated heap on clear.\n",
priv->frames_count);
while (!list_empty(&priv->free_frames)) {
element = priv->free_frames.next;
list_del(element);
kfree(list_entry(element, struct iwl_frame, list));
priv->frames_count--;
}
if (priv->frames_count) {
IWL_WARNING("%d frames still in use. Did we lose one?\n",
priv->frames_count);
priv->frames_count = 0;
}
}
static struct iwl_frame *iwl_get_free_frame(struct iwl_priv *priv)
{
struct iwl_frame *frame;
struct list_head *element;
if (list_empty(&priv->free_frames)) {
frame = kzalloc(sizeof(*frame), GFP_KERNEL);
if (!frame) {
IWL_ERROR("Could not allocate frame!\n");
return NULL;
}
priv->frames_count++;
return frame;
}
element = priv->free_frames.next;
list_del(element);
return list_entry(element, struct iwl_frame, list);
}
static void iwl_free_frame(struct iwl_priv *priv, struct iwl_frame *frame)
{
memset(frame, 0, sizeof(*frame));
list_add(&frame->list, &priv->free_frames);
}
static unsigned int iwl_fill_beacon_frame(struct iwl_priv *priv,
struct ieee80211_hdr *hdr,
const u8 *dest, int left)
{
if (!iwl_is_associated(priv) || !priv->ibss_beacon ||
((priv->iw_mode != NL80211_IFTYPE_ADHOC) &&
(priv->iw_mode != NL80211_IFTYPE_AP)))
return 0;
if (priv->ibss_beacon->len > left)
return 0;
memcpy(hdr, priv->ibss_beacon->data, priv->ibss_beacon->len);
return priv->ibss_beacon->len;
}
static u8 iwl_rate_get_lowest_plcp(struct iwl_priv *priv)
{
int i;
int rate_mask;
/* Set rate mask*/
if (priv->staging_rxon.flags & RXON_FLG_BAND_24G_MSK)
rate_mask = priv->active_rate_basic & IWL_CCK_RATES_MASK;
else
rate_mask = priv->active_rate_basic & IWL_OFDM_RATES_MASK;
/* Find lowest valid rate */
for (i = IWL_RATE_1M_INDEX; i != IWL_RATE_INVALID;
i = iwl_rates[i].next_ieee) {
if (rate_mask & (1 << i))
return iwl_rates[i].plcp;
}
/* No valid rate was found. Assign the lowest one */
if (priv->staging_rxon.flags & RXON_FLG_BAND_24G_MSK)
return IWL_RATE_1M_PLCP;
else
return IWL_RATE_6M_PLCP;
}
static unsigned int iwl_hw_get_beacon_cmd(struct iwl_priv *priv,
struct iwl_frame *frame, u8 rate)
{
struct iwl_tx_beacon_cmd *tx_beacon_cmd;
unsigned int frame_size;
tx_beacon_cmd = &frame->u.beacon;
memset(tx_beacon_cmd, 0, sizeof(*tx_beacon_cmd));
tx_beacon_cmd->tx.sta_id = priv->hw_params.bcast_sta_id;
tx_beacon_cmd->tx.stop_time.life_time = TX_CMD_LIFE_TIME_INFINITE;
frame_size = iwl_fill_beacon_frame(priv, tx_beacon_cmd->frame,
iwl_bcast_addr,
sizeof(frame->u) - sizeof(*tx_beacon_cmd));
BUG_ON(frame_size > MAX_MPDU_SIZE);
tx_beacon_cmd->tx.len = cpu_to_le16((u16)frame_size);
if ((rate == IWL_RATE_1M_PLCP) || (rate >= IWL_RATE_2M_PLCP))
tx_beacon_cmd->tx.rate_n_flags =
iwl_hw_set_rate_n_flags(rate, RATE_MCS_CCK_MSK);
else
tx_beacon_cmd->tx.rate_n_flags =
iwl_hw_set_rate_n_flags(rate, 0);
tx_beacon_cmd->tx.tx_flags = TX_CMD_FLG_SEQ_CTL_MSK |
TX_CMD_FLG_TSF_MSK |
TX_CMD_FLG_STA_RATE_MSK;
return sizeof(*tx_beacon_cmd) + frame_size;
}
static int iwl_send_beacon_cmd(struct iwl_priv *priv)
{
struct iwl_frame *frame;
unsigned int frame_size;
int rc;
u8 rate;
frame = iwl_get_free_frame(priv);
if (!frame) {
IWL_ERROR("Could not obtain free frame buffer for beacon "
"command.\n");
return -ENOMEM;
}
rate = iwl_rate_get_lowest_plcp(priv);
frame_size = iwl_hw_get_beacon_cmd(priv, frame, rate);
rc = iwl_send_cmd_pdu(priv, REPLY_TX_BEACON, frame_size,
&frame->u.cmd[0]);
iwl_free_frame(priv, frame);
return rc;
}
/******************************************************************************
*
* Misc. internal state and helper functions
*
******************************************************************************/
static void iwl_ht_conf(struct iwl_priv *priv,
struct ieee80211_bss_conf *bss_conf)
{
struct ieee80211_sta_ht_cap *ht_conf;
struct iwl_ht_info *iwl_conf = &priv->current_ht_config;
struct ieee80211_sta *sta;
IWL_DEBUG_MAC80211("enter: \n");
if (!iwl_conf->is_ht)
return;
/*
* It is totally wrong to base global information on something
* that is valid only when associated, alas, this driver works
* that way and I don't know how to fix it.
*/
rcu_read_lock();
sta = ieee80211_find_sta(priv->hw, priv->bssid);
if (!sta) {
rcu_read_unlock();
return;
}
ht_conf = &sta->ht_cap;
if (ht_conf->cap & IEEE80211_HT_CAP_SGI_20)
iwl_conf->sgf |= HT_SHORT_GI_20MHZ;
if (ht_conf->cap & IEEE80211_HT_CAP_SGI_40)
iwl_conf->sgf |= HT_SHORT_GI_40MHZ;
iwl_conf->is_green_field = !!(ht_conf->cap & IEEE80211_HT_CAP_GRN_FLD);
iwl_conf->max_amsdu_size =
!!(ht_conf->cap & IEEE80211_HT_CAP_MAX_AMSDU);
iwl_conf->supported_chan_width =
!!(ht_conf->cap & IEEE80211_HT_CAP_SUP_WIDTH_20_40);
iwl_conf->extension_chan_offset = bss_conf->ht.secondary_channel_offset;
/* If no above or below channel supplied disable FAT channel */
if (iwl_conf->extension_chan_offset != IEEE80211_HT_PARAM_CHA_SEC_ABOVE &&
iwl_conf->extension_chan_offset != IEEE80211_HT_PARAM_CHA_SEC_BELOW) {
iwl_conf->extension_chan_offset = IEEE80211_HT_PARAM_CHA_SEC_NONE;
iwl_conf->supported_chan_width = 0;
}
iwl_conf->sm_ps = (u8)((ht_conf->cap & IEEE80211_HT_CAP_SM_PS) >> 2);
memcpy(&iwl_conf->mcs, &ht_conf->mcs, 16);
iwl_conf->tx_chan_width = bss_conf->ht.width_40_ok;
iwl_conf->ht_protection =
bss_conf->ht.operation_mode & IEEE80211_HT_OP_MODE_PROTECTION;
iwl_conf->non_GF_STA_present =
!!(bss_conf->ht.operation_mode & IEEE80211_HT_OP_MODE_NON_GF_STA_PRSNT);
rcu_read_unlock();
IWL_DEBUG_MAC80211("leave\n");
}
/*
* QoS support
*/
static void iwl_activate_qos(struct iwl_priv *priv, u8 force)
{
if (test_bit(STATUS_EXIT_PENDING, &priv->status))
return;
if (!priv->qos_data.qos_enable)
return;
priv->qos_data.def_qos_parm.qos_flags = 0;
if (priv->qos_data.qos_cap.q_AP.queue_request &&
!priv->qos_data.qos_cap.q_AP.txop_request)
priv->qos_data.def_qos_parm.qos_flags |=
QOS_PARAM_FLG_TXOP_TYPE_MSK;
if (priv->qos_data.qos_active)
priv->qos_data.def_qos_parm.qos_flags |=
QOS_PARAM_FLG_UPDATE_EDCA_MSK;
if (priv->current_ht_config.is_ht)
priv->qos_data.def_qos_parm.qos_flags |= QOS_PARAM_FLG_TGN_MSK;
if (force || iwl_is_associated(priv)) {
IWL_DEBUG_QOS("send QoS cmd with Qos active=%d FLAGS=0x%X\n",
priv->qos_data.qos_active,
priv->qos_data.def_qos_parm.qos_flags);
iwl_send_cmd_pdu_async(priv, REPLY_QOS_PARAM,
sizeof(struct iwl_qosparam_cmd),
&priv->qos_data.def_qos_parm, NULL);
}
}
#define MAX_UCODE_BEACON_INTERVAL 4096
static u16 iwl_adjust_beacon_interval(u16 beacon_val)
{
u16 new_val = 0;
u16 beacon_factor = 0;
beacon_factor = (beacon_val + MAX_UCODE_BEACON_INTERVAL)
/ MAX_UCODE_BEACON_INTERVAL;
new_val = beacon_val / beacon_factor;
return new_val;
}
static void iwl_setup_rxon_timing(struct iwl_priv *priv)
{
u64 tsf;
s32 interval_tm, rem;
unsigned long flags;
struct ieee80211_conf *conf = NULL;
u16 beacon_int = 0;
conf = ieee80211_get_hw_conf(priv->hw);
spin_lock_irqsave(&priv->lock, flags);
priv->rxon_timing.timestamp = cpu_to_le64(priv->timestamp);
priv->rxon_timing.listen_interval = cpu_to_le16(conf->listen_interval);
if (priv->iw_mode == NL80211_IFTYPE_STATION) {
beacon_int = iwl_adjust_beacon_interval(priv->beacon_int);
priv->rxon_timing.atim_window = 0;
} else {
beacon_int = iwl_adjust_beacon_interval(conf->beacon_int);
/* TODO: we need to get atim_window from upper stack
* for now we set to 0 */
priv->rxon_timing.atim_window = 0;
}
priv->rxon_timing.beacon_interval = cpu_to_le16(beacon_int);
tsf = priv->timestamp; /* tsf is modifed by do_div: copy it */
interval_tm = beacon_int * 1024;
rem = do_div(tsf, interval_tm);
priv->rxon_timing.beacon_init_val = cpu_to_le32(interval_tm - rem);
spin_unlock_irqrestore(&priv->lock, flags);
IWL_DEBUG_ASSOC("beacon interval %d beacon timer %d beacon tim %d\n",
le16_to_cpu(priv->rxon_timing.beacon_interval),
le32_to_cpu(priv->rxon_timing.beacon_init_val),
le16_to_cpu(priv->rxon_timing.atim_window));
}
static void iwl_set_flags_for_band(struct iwl_priv *priv,
enum ieee80211_band band)
{
if (band == IEEE80211_BAND_5GHZ) {
priv->staging_rxon.flags &=
~(RXON_FLG_BAND_24G_MSK | RXON_FLG_AUTO_DETECT_MSK
| RXON_FLG_CCK_MSK);
priv->staging_rxon.flags |= RXON_FLG_SHORT_SLOT_MSK;
} else {
/* Copied from iwl_post_associate() */
if (priv->assoc_capability & WLAN_CAPABILITY_SHORT_SLOT_TIME)
priv->staging_rxon.flags |= RXON_FLG_SHORT_SLOT_MSK;
else
priv->staging_rxon.flags &= ~RXON_FLG_SHORT_SLOT_MSK;
if (priv->iw_mode == NL80211_IFTYPE_ADHOC)
priv->staging_rxon.flags &= ~RXON_FLG_SHORT_SLOT_MSK;
priv->staging_rxon.flags |= RXON_FLG_BAND_24G_MSK;
priv->staging_rxon.flags |= RXON_FLG_AUTO_DETECT_MSK;
priv->staging_rxon.flags &= ~RXON_FLG_CCK_MSK;
}
}
/*
* initialize rxon structure with default values from eeprom
*/
static void iwl_connection_init_rx_config(struct iwl_priv *priv, int mode)
{
const struct iwl_channel_info *ch_info;
memset(&priv->staging_rxon, 0, sizeof(priv->staging_rxon));
switch (mode) {
case NL80211_IFTYPE_AP:
priv->staging_rxon.dev_type = RXON_DEV_TYPE_AP;
break;
case NL80211_IFTYPE_STATION:
priv->staging_rxon.dev_type = RXON_DEV_TYPE_ESS;
priv->staging_rxon.filter_flags = RXON_FILTER_ACCEPT_GRP_MSK;
break;
case NL80211_IFTYPE_ADHOC:
priv->staging_rxon.dev_type = RXON_DEV_TYPE_IBSS;
priv->staging_rxon.flags = RXON_FLG_SHORT_PREAMBLE_MSK;
priv->staging_rxon.filter_flags = RXON_FILTER_BCON_AWARE_MSK |
RXON_FILTER_ACCEPT_GRP_MSK;
break;
case NL80211_IFTYPE_MONITOR:
priv->staging_rxon.dev_type = RXON_DEV_TYPE_SNIFFER;
priv->staging_rxon.filter_flags = RXON_FILTER_PROMISC_MSK |
RXON_FILTER_CTL2HOST_MSK | RXON_FILTER_ACCEPT_GRP_MSK;
break;
default:
IWL_ERROR("Unsupported interface type %d\n", mode);
break;
}
#if 0
/* TODO: Figure out when short_preamble would be set and cache from
* that */
if (!hw_to_local(priv->hw)->short_preamble)
priv->staging_rxon.flags &= ~RXON_FLG_SHORT_PREAMBLE_MSK;
else
priv->staging_rxon.flags |= RXON_FLG_SHORT_PREAMBLE_MSK;
#endif
ch_info = iwl_get_channel_info(priv, priv->band,
le16_to_cpu(priv->active_rxon.channel));
if (!ch_info)
ch_info = &priv->channel_info[0];
/*
* in some case A channels are all non IBSS
* in this case force B/G channel
*/
if ((priv->iw_mode == NL80211_IFTYPE_ADHOC) &&
!(is_channel_ibss(ch_info)))
ch_info = &priv->channel_info[0];
priv->staging_rxon.channel = cpu_to_le16(ch_info->channel);
priv->band = ch_info->band;
iwl_set_flags_for_band(priv, priv->band);
priv->staging_rxon.ofdm_basic_rates =
(IWL_OFDM_RATES_MASK >> IWL_FIRST_OFDM_RATE) & 0xFF;
priv->staging_rxon.cck_basic_rates =
(IWL_CCK_RATES_MASK >> IWL_FIRST_CCK_RATE) & 0xF;
priv->staging_rxon.flags &= ~(RXON_FLG_CHANNEL_MODE_MIXED_MSK |
RXON_FLG_CHANNEL_MODE_PURE_40_MSK);
memcpy(priv->staging_rxon.node_addr, priv->mac_addr, ETH_ALEN);
memcpy(priv->staging_rxon.wlap_bssid_addr, priv->mac_addr, ETH_ALEN);
priv->staging_rxon.ofdm_ht_single_stream_basic_rates = 0xff;
priv->staging_rxon.ofdm_ht_dual_stream_basic_rates = 0xff;
iwl_set_rxon_chain(priv);
}
static int iwl_set_mode(struct iwl_priv *priv, int mode)
{
iwl_connection_init_rx_config(priv, mode);
memcpy(priv->staging_rxon.node_addr, priv->mac_addr, ETH_ALEN);
iwl_clear_stations_table(priv);
/* dont commit rxon if rf-kill is on*/
if (!iwl_is_ready_rf(priv))
return -EAGAIN;
cancel_delayed_work(&priv->scan_check);
if (iwl_scan_cancel_timeout(priv, 100)) {
IWL_WARNING("Aborted scan still in progress after 100ms\n");
IWL_DEBUG_MAC80211("leaving - scan abort failed.\n");
return -EAGAIN;
}
iwl_commit_rxon(priv);
return 0;
}
static void iwl_set_rate(struct iwl_priv *priv)
{
const struct ieee80211_supported_band *hw = NULL;
struct ieee80211_rate *rate;
int i;
hw = iwl_get_hw_mode(priv, priv->band);
if (!hw) {
IWL_ERROR("Failed to set rate: unable to get hw mode\n");
return;
}
priv->active_rate = 0;
priv->active_rate_basic = 0;
for (i = 0; i < hw->n_bitrates; i++) {
rate = &(hw->bitrates[i]);
if (rate->hw_value < IWL_RATE_COUNT)
priv->active_rate |= (1 << rate->hw_value);
}
IWL_DEBUG_RATE("Set active_rate = %0x, active_rate_basic = %0x\n",
priv->active_rate, priv->active_rate_basic);
/*
* If a basic rate is configured, then use it (adding IWL_RATE_1M_MASK)
* otherwise set it to the default of all CCK rates and 6, 12, 24 for
* OFDM
*/
if (priv->active_rate_basic & IWL_CCK_BASIC_RATES_MASK)
priv->staging_rxon.cck_basic_rates =
((priv->active_rate_basic &
IWL_CCK_RATES_MASK) >> IWL_FIRST_CCK_RATE) & 0xF;
else
priv->staging_rxon.cck_basic_rates =
(IWL_CCK_BASIC_RATES_MASK >> IWL_FIRST_CCK_RATE) & 0xF;
if (priv->active_rate_basic & IWL_OFDM_BASIC_RATES_MASK)
priv->staging_rxon.ofdm_basic_rates =
((priv->active_rate_basic &
(IWL_OFDM_BASIC_RATES_MASK | IWL_RATE_6M_MASK)) >>
IWL_FIRST_OFDM_RATE) & 0xFF;
else
priv->staging_rxon.ofdm_basic_rates =
(IWL_OFDM_BASIC_RATES_MASK >> IWL_FIRST_OFDM_RATE) & 0xFF;
}
/******************************************************************************
*
* Generic RX handler implementations
*
******************************************************************************/
static void iwl_rx_reply_alive(struct iwl_priv *priv,
struct iwl_rx_mem_buffer *rxb)
{
struct iwl_rx_packet *pkt = (struct iwl_rx_packet *)rxb->skb->data;
struct iwl_alive_resp *palive;
struct delayed_work *pwork;
palive = &pkt->u.alive_frame;
IWL_DEBUG_INFO("Alive ucode status 0x%08X revision "
"0x%01X 0x%01X\n",
palive->is_valid, palive->ver_type,
palive->ver_subtype);
if (palive->ver_subtype == INITIALIZE_SUBTYPE) {
IWL_DEBUG_INFO("Initialization Alive received.\n");
memcpy(&priv->card_alive_init,
&pkt->u.alive_frame,
sizeof(struct iwl_init_alive_resp));
pwork = &priv->init_alive_start;
} else {
IWL_DEBUG_INFO("Runtime Alive received.\n");
memcpy(&priv->card_alive, &pkt->u.alive_frame,
sizeof(struct iwl_alive_resp));
pwork = &priv->alive_start;
}
/* We delay the ALIVE response by 5ms to
* give the HW RF Kill time to activate... */
if (palive->is_valid == UCODE_VALID_OK)
queue_delayed_work(priv->workqueue, pwork,
msecs_to_jiffies(5));
else
IWL_WARNING("uCode did not respond OK.\n");
}
static void iwl_rx_reply_error(struct iwl_priv *priv,
struct iwl_rx_mem_buffer *rxb)
{
struct iwl_rx_packet *pkt = (struct iwl_rx_packet *)rxb->skb->data;
IWL_ERROR("Error Reply type 0x%08X cmd %s (0x%02X) "
"seq 0x%04X ser 0x%08X\n",
le32_to_cpu(pkt->u.err_resp.error_type),
get_cmd_string(pkt->u.err_resp.cmd_id),
pkt->u.err_resp.cmd_id,
le16_to_cpu(pkt->u.err_resp.bad_cmd_seq_num),
le32_to_cpu(pkt->u.err_resp.error_info));
}
#define TX_STATUS_ENTRY(x) case TX_STATUS_FAIL_ ## x: return #x
static void iwl_rx_csa(struct iwl_priv *priv, struct iwl_rx_mem_buffer *rxb)
{
struct iwl_rx_packet *pkt = (struct iwl_rx_packet *)rxb->skb->data;
struct iwl_rxon_cmd *rxon = (void *)&priv->active_rxon;
struct iwl4965_csa_notification *csa = &(pkt->u.csa_notif);
IWL_DEBUG_11H("CSA notif: channel %d, status %d\n",
le16_to_cpu(csa->channel), le32_to_cpu(csa->status));
rxon->channel = csa->channel;
priv->staging_rxon.channel = csa->channel;
}
static void iwl_rx_pm_sleep_notif(struct iwl_priv *priv,
struct iwl_rx_mem_buffer *rxb)
{
#ifdef CONFIG_IWLWIFI_DEBUG
struct iwl_rx_packet *pkt = (struct iwl_rx_packet *)rxb->skb->data;
struct iwl4965_sleep_notification *sleep = &(pkt->u.sleep_notif);
IWL_DEBUG_RX("sleep mode: %d, src: %d\n",
sleep->pm_sleep_mode, sleep->pm_wakeup_src);
#endif
}
static void iwl_rx_pm_debug_statistics_notif(struct iwl_priv *priv,
struct iwl_rx_mem_buffer *rxb)
{
struct iwl_rx_packet *pkt = (struct iwl_rx_packet *)rxb->skb->data;
IWL_DEBUG_RADIO("Dumping %d bytes of unhandled "
"notification for %s:\n",
le32_to_cpu(pkt->len), get_cmd_string(pkt->hdr.cmd));
iwl_print_hex_dump(priv, IWL_DL_RADIO, pkt->u.raw, le32_to_cpu(pkt->len));
}
static void iwl_bg_beacon_update(struct work_struct *work)
{
struct iwl_priv *priv =
container_of(work, struct iwl_priv, beacon_update);
struct sk_buff *beacon;
/* Pull updated AP beacon from mac80211. will fail if not in AP mode */
beacon = ieee80211_beacon_get(priv->hw, priv->vif);
if (!beacon) {
IWL_ERROR("update beacon failed\n");
return;
}
mutex_lock(&priv->mutex);
/* new beacon skb is allocated every time; dispose previous.*/
if (priv->ibss_beacon)
dev_kfree_skb(priv->ibss_beacon);
priv->ibss_beacon = beacon;
mutex_unlock(&priv->mutex);
iwl_send_beacon_cmd(priv);
}
/**
* iwl_bg_statistics_periodic - Timer callback to queue statistics
*
* This callback is provided in order to send a statistics request.
*
* This timer function is continually reset to execute within
* REG_RECALIB_PERIOD seconds since the last STATISTICS_NOTIFICATION
* was received. We need to ensure we receive the statistics in order
* to update the temperature used for calibrating the TXPOWER.
*/
static void iwl_bg_statistics_periodic(unsigned long data)
{
struct iwl_priv *priv = (struct iwl_priv *)data;
if (test_bit(STATUS_EXIT_PENDING, &priv->status))
return;
/* dont send host command if rf-kill is on */
if (!iwl_is_ready_rf(priv))
return;
iwl_send_statistics_request(priv, CMD_ASYNC);
}
static void iwl_rx_beacon_notif(struct iwl_priv *priv,
struct iwl_rx_mem_buffer *rxb)
{
#ifdef CONFIG_IWLWIFI_DEBUG
struct iwl_rx_packet *pkt = (struct iwl_rx_packet *)rxb->skb->data;
struct iwl4965_beacon_notif *beacon = &(pkt->u.beacon_status);
u8 rate = iwl_hw_get_rate(beacon->beacon_notify_hdr.rate_n_flags);
IWL_DEBUG_RX("beacon status %x retries %d iss %d "
"tsf %d %d rate %d\n",
le32_to_cpu(beacon->beacon_notify_hdr.u.status) & TX_STATUS_MSK,
beacon->beacon_notify_hdr.failure_frame,
le32_to_cpu(beacon->ibss_mgr_status),
le32_to_cpu(beacon->high_tsf),
le32_to_cpu(beacon->low_tsf), rate);
#endif
if ((priv->iw_mode == NL80211_IFTYPE_AP) &&
(!test_bit(STATUS_EXIT_PENDING, &priv->status)))
queue_work(priv->workqueue, &priv->beacon_update);
}
/* Handle notification from uCode that card's power state is changing
* due to software, hardware, or critical temperature RFKILL */
static void iwl_rx_card_state_notif(struct iwl_priv *priv,
struct iwl_rx_mem_buffer *rxb)
{
struct iwl_rx_packet *pkt = (struct iwl_rx_packet *)rxb->skb->data;
u32 flags = le32_to_cpu(pkt->u.card_state_notif.flags);
unsigned long status = priv->status;
IWL_DEBUG_RF_KILL("Card state received: HW:%s SW:%s\n",
(flags & HW_CARD_DISABLED) ? "Kill" : "On",
(flags & SW_CARD_DISABLED) ? "Kill" : "On");
if (flags & (SW_CARD_DISABLED | HW_CARD_DISABLED |
RF_CARD_DISABLED)) {
iwl_write32(priv, CSR_UCODE_DRV_GP1_SET,
CSR_UCODE_DRV_GP1_BIT_CMD_BLOCKED);
if (!iwl_grab_nic_access(priv)) {
iwl_write_direct32(
priv, HBUS_TARG_MBX_C,
HBUS_TARG_MBX_C_REG_BIT_CMD_BLOCKED);
iwl_release_nic_access(priv);
}
if (!(flags & RXON_CARD_DISABLED)) {
iwl_write32(priv, CSR_UCODE_DRV_GP1_CLR,
CSR_UCODE_DRV_GP1_BIT_CMD_BLOCKED);
if (!iwl_grab_nic_access(priv)) {
iwl_write_direct32(
priv, HBUS_TARG_MBX_C,
HBUS_TARG_MBX_C_REG_BIT_CMD_BLOCKED);
iwl_release_nic_access(priv);
}
}
if (flags & RF_CARD_DISABLED) {
iwl_write32(priv, CSR_UCODE_DRV_GP1_SET,
CSR_UCODE_DRV_GP1_REG_BIT_CT_KILL_EXIT);
iwl_read32(priv, CSR_UCODE_DRV_GP1);
if (!iwl_grab_nic_access(priv))
iwl_release_nic_access(priv);
}
}
if (flags & HW_CARD_DISABLED)
set_bit(STATUS_RF_KILL_HW, &priv->status);
else
clear_bit(STATUS_RF_KILL_HW, &priv->status);
if (flags & SW_CARD_DISABLED)
set_bit(STATUS_RF_KILL_SW, &priv->status);
else
clear_bit(STATUS_RF_KILL_SW, &priv->status);
if (!(flags & RXON_CARD_DISABLED))
iwl_scan_cancel(priv);
if ((test_bit(STATUS_RF_KILL_HW, &status) !=
test_bit(STATUS_RF_KILL_HW, &priv->status)) ||
(test_bit(STATUS_RF_KILL_SW, &status) !=
test_bit(STATUS_RF_KILL_SW, &priv->status)))
queue_work(priv->workqueue, &priv->rf_kill);
else
wake_up_interruptible(&priv->wait_command_queue);
}
int iwl_set_pwr_src(struct iwl_priv *priv, enum iwl_pwr_src src)
{
int ret;
unsigned long flags;
spin_lock_irqsave(&priv->lock, flags);
ret = iwl_grab_nic_access(priv);
if (ret)
goto err;
if (src == IWL_PWR_SRC_VAUX) {
u32 val;
ret = pci_read_config_dword(priv->pci_dev, PCI_CFG_POWER_SOURCE,
&val);
if (val & PCI_CFG_PMC_PME_FROM_D3COLD_SUPPORT)
iwl_set_bits_mask_prph(priv, APMG_PS_CTRL_REG,
APMG_PS_CTRL_VAL_PWR_SRC_VAUX,
~APMG_PS_CTRL_MSK_PWR_SRC);
} else {
iwl_set_bits_mask_prph(priv, APMG_PS_CTRL_REG,
APMG_PS_CTRL_VAL_PWR_SRC_VMAIN,
~APMG_PS_CTRL_MSK_PWR_SRC);
}
iwl_release_nic_access(priv);
err:
spin_unlock_irqrestore(&priv->lock, flags);
return ret;
}
/**
* iwl_setup_rx_handlers - Initialize Rx handler callbacks
*
* Setup the RX handlers for each of the reply types sent from the uCode
* to the host.
*
* This function chains into the hardware specific files for them to setup
* any hardware specific handlers as well.
*/
static void iwl_setup_rx_handlers(struct iwl_priv *priv)
{
priv->rx_handlers[REPLY_ALIVE] = iwl_rx_reply_alive;
priv->rx_handlers[REPLY_ERROR] = iwl_rx_reply_error;
priv->rx_handlers[CHANNEL_SWITCH_NOTIFICATION] = iwl_rx_csa;
priv->rx_handlers[PM_SLEEP_NOTIFICATION] = iwl_rx_pm_sleep_notif;
priv->rx_handlers[PM_DEBUG_STATISTIC_NOTIFIC] =
iwl_rx_pm_debug_statistics_notif;
priv->rx_handlers[BEACON_NOTIFICATION] = iwl_rx_beacon_notif;
/*
* The same handler is used for both the REPLY to a discrete
* statistics request from the host as well as for the periodic
* statistics notifications (after received beacons) from the uCode.
*/
priv->rx_handlers[REPLY_STATISTICS_CMD] = iwl_rx_statistics;
priv->rx_handlers[STATISTICS_NOTIFICATION] = iwl_rx_statistics;
iwl_setup_spectrum_handlers(priv);
iwl_setup_rx_scan_handlers(priv);
/* status change handler */
priv->rx_handlers[CARD_STATE_NOTIFICATION] = iwl_rx_card_state_notif;
priv->rx_handlers[MISSED_BEACONS_NOTIFICATION] =
iwl_rx_missed_beacon_notif;
/* Rx handlers */
priv->rx_handlers[REPLY_RX_PHY_CMD] = iwl_rx_reply_rx_phy;
priv->rx_handlers[REPLY_RX_MPDU_CMD] = iwl_rx_reply_rx;
/* block ack */
priv->rx_handlers[REPLY_COMPRESSED_BA] = iwl_rx_reply_compressed_ba;
/* Set up hardware specific Rx handlers */
priv->cfg->ops->lib->rx_handler_setup(priv);
}
/*
* this should be called while priv->lock is locked
*/
static void __iwl_rx_replenish(struct iwl_priv *priv)
{
iwl_rx_allocate(priv);
iwl_rx_queue_restock(priv);
}
/**
* iwl_rx_handle - Main entry function for receiving responses from uCode
*
* Uses the priv->rx_handlers callback function array to invoke
* the appropriate handlers, including command responses,
* frame-received notifications, and other notifications.
*/
void iwl_rx_handle(struct iwl_priv *priv)
{
struct iwl_rx_mem_buffer *rxb;
struct iwl_rx_packet *pkt;
struct iwl_rx_queue *rxq = &priv->rxq;
u32 r, i;
int reclaim;
unsigned long flags;
u8 fill_rx = 0;
u32 count = 8;
/* uCode's read index (stored in shared DRAM) indicates the last Rx
* buffer that the driver may process (last buffer filled by ucode). */
r = le16_to_cpu(rxq->rb_stts->closed_rb_num) & 0x0FFF;
i = rxq->read;
/* Rx interrupt, but nothing sent from uCode */
if (i == r)
IWL_DEBUG(IWL_DL_RX, "r = %d, i = %d\n", r, i);
if (iwl_rx_queue_space(rxq) > (RX_QUEUE_SIZE / 2))
fill_rx = 1;
while (i != r) {
rxb = rxq->queue[i];
/* If an RXB doesn't have a Rx queue slot associated with it,
* then a bug has been introduced in the queue refilling
* routines -- catch it here */
BUG_ON(rxb == NULL);
rxq->queue[i] = NULL;
dma_sync_single_range_for_cpu(
&priv->pci_dev->dev, rxb->real_dma_addr,
rxb->aligned_dma_addr - rxb->real_dma_addr,
priv->hw_params.rx_buf_size,
PCI_DMA_FROMDEVICE);
pkt = (struct iwl_rx_packet *)rxb->skb->data;
/* Reclaim a command buffer only if this packet is a response
* to a (driver-originated) command.
* If the packet (e.g. Rx frame) originated from uCode,
* there is no command buffer to reclaim.
* Ucode should set SEQ_RX_FRAME bit if ucode-originated,
* but apparently a few don't get set; catch them here. */
reclaim = !(pkt->hdr.sequence & SEQ_RX_FRAME) &&
(pkt->hdr.cmd != REPLY_RX_PHY_CMD) &&
(pkt->hdr.cmd != REPLY_RX) &&
(pkt->hdr.cmd != REPLY_RX_MPDU_CMD) &&
(pkt->hdr.cmd != REPLY_COMPRESSED_BA) &&
(pkt->hdr.cmd != STATISTICS_NOTIFICATION) &&
(pkt->hdr.cmd != REPLY_TX);
/* Based on type of command response or notification,
* handle those that need handling via function in
* rx_handlers table. See iwl_setup_rx_handlers() */
if (priv->rx_handlers[pkt->hdr.cmd]) {
IWL_DEBUG(IWL_DL_RX, "r = %d, i = %d, %s, 0x%02x\n", r,
i, get_cmd_string(pkt->hdr.cmd), pkt->hdr.cmd);
priv->rx_handlers[pkt->hdr.cmd] (priv, rxb);
} else {
/* No handling needed */
IWL_DEBUG(IWL_DL_RX,
"r %d i %d No handler needed for %s, 0x%02x\n",
r, i, get_cmd_string(pkt->hdr.cmd),
pkt->hdr.cmd);
}
if (reclaim) {
/* Invoke any callbacks, transfer the skb to caller, and
* fire off the (possibly) blocking iwl_send_cmd()
* as we reclaim the driver command queue */
if (rxb && rxb->skb)
iwl_tx_cmd_complete(priv, rxb);
else
IWL_WARNING("Claim null rxb?\n");
}
/* For now we just don't re-use anything. We can tweak this
* later to try and re-use notification packets and SKBs that
* fail to Rx correctly */
if (rxb->skb != NULL) {
priv->alloc_rxb_skb--;
dev_kfree_skb_any(rxb->skb);
rxb->skb = NULL;
}
pci_unmap_single(priv->pci_dev, rxb->real_dma_addr,
priv->hw_params.rx_buf_size + 256,
PCI_DMA_FROMDEVICE);
spin_lock_irqsave(&rxq->lock, flags);
list_add_tail(&rxb->list, &priv->rxq.rx_used);
spin_unlock_irqrestore(&rxq->lock, flags);
i = (i + 1) & RX_QUEUE_MASK;
/* If there are a lot of unused frames,
* restock the Rx queue so ucode wont assert. */
if (fill_rx) {
count++;
if (count >= 8) {
priv->rxq.read = i;
__iwl_rx_replenish(priv);
count = 0;
}
}
}
/* Backtrack one entry */
priv->rxq.read = i;
iwl_rx_queue_restock(priv);
}
#ifdef CONFIG_IWLWIFI_DEBUG
static void iwl_print_rx_config_cmd(struct iwl_priv *priv)
{
struct iwl_rxon_cmd *rxon = &priv->staging_rxon;
IWL_DEBUG_RADIO("RX CONFIG:\n");
iwl_print_hex_dump(priv, IWL_DL_RADIO, (u8 *) rxon, sizeof(*rxon));
IWL_DEBUG_RADIO("u16 channel: 0x%x\n", le16_to_cpu(rxon->channel));
IWL_DEBUG_RADIO("u32 flags: 0x%08X\n", le32_to_cpu(rxon->flags));
IWL_DEBUG_RADIO("u32 filter_flags: 0x%08x\n",
le32_to_cpu(rxon->filter_flags));
IWL_DEBUG_RADIO("u8 dev_type: 0x%x\n", rxon->dev_type);
IWL_DEBUG_RADIO("u8 ofdm_basic_rates: 0x%02x\n",
rxon->ofdm_basic_rates);
IWL_DEBUG_RADIO("u8 cck_basic_rates: 0x%02x\n", rxon->cck_basic_rates);
IWL_DEBUG_RADIO("u8[6] node_addr: %pM\n", rxon->node_addr);
IWL_DEBUG_RADIO("u8[6] bssid_addr: %pM\n", rxon->bssid_addr);
IWL_DEBUG_RADIO("u16 assoc_id: 0x%x\n", le16_to_cpu(rxon->assoc_id));
}
#endif
static void iwl_enable_interrupts(struct iwl_priv *priv)
{
IWL_DEBUG_ISR("Enabling interrupts\n");
set_bit(STATUS_INT_ENABLED, &priv->status);
iwl_write32(priv, CSR_INT_MASK, CSR_INI_SET_MASK);
}
/* call this function to flush any scheduled tasklet */
static inline void iwl_synchronize_irq(struct iwl_priv *priv)
{
/* wait to make sure we flush pending tasklet*/
synchronize_irq(priv->pci_dev->irq);
tasklet_kill(&priv->irq_tasklet);
}
static inline void iwl_disable_interrupts(struct iwl_priv *priv)
{
clear_bit(STATUS_INT_ENABLED, &priv->status);
/* disable interrupts from uCode/NIC to host */
iwl_write32(priv, CSR_INT_MASK, 0x00000000);
/* acknowledge/clear/reset any interrupts still pending
* from uCode or flow handler (Rx/Tx DMA) */
iwl_write32(priv, CSR_INT, 0xffffffff);
iwl_write32(priv, CSR_FH_INT_STATUS, 0xffffffff);
IWL_DEBUG_ISR("Disabled interrupts\n");
}
/**
* iwl_irq_handle_error - called for HW or SW error interrupt from card
*/
static void iwl_irq_handle_error(struct iwl_priv *priv)
{
/* Set the FW error flag -- cleared on iwl_down */
set_bit(STATUS_FW_ERROR, &priv->status);
/* Cancel currently queued command. */
clear_bit(STATUS_HCMD_ACTIVE, &priv->status);
#ifdef CONFIG_IWLWIFI_DEBUG
if (priv->debug_level & IWL_DL_FW_ERRORS) {
iwl_dump_nic_error_log(priv);
iwl_dump_nic_event_log(priv);
iwl_print_rx_config_cmd(priv);
}
#endif
wake_up_interruptible(&priv->wait_command_queue);
/* Keep the restart process from trying to send host
* commands by clearing the INIT status bit */
clear_bit(STATUS_READY, &priv->status);
if (!test_bit(STATUS_EXIT_PENDING, &priv->status)) {
IWL_DEBUG(IWL_DL_FW_ERRORS,
"Restarting adapter due to uCode error.\n");
if (iwl_is_associated(priv)) {
memcpy(&priv->recovery_rxon, &priv->active_rxon,
sizeof(priv->recovery_rxon));
priv->error_recovering = 1;
}
if (priv->cfg->mod_params->restart_fw)
queue_work(priv->workqueue, &priv->restart);
}
}
static void iwl_error_recovery(struct iwl_priv *priv)
{
unsigned long flags;
memcpy(&priv->staging_rxon, &priv->recovery_rxon,
sizeof(priv->staging_rxon));
priv->staging_rxon.filter_flags &= ~RXON_FILTER_ASSOC_MSK;
iwl_commit_rxon(priv);
iwl_rxon_add_station(priv, priv->bssid, 1);
spin_lock_irqsave(&priv->lock, flags);
priv->assoc_id = le16_to_cpu(priv->staging_rxon.assoc_id);
priv->error_recovering = 0;
spin_unlock_irqrestore(&priv->lock, flags);
}
static void iwl_irq_tasklet(struct iwl_priv *priv)
{
u32 inta, handled = 0;
u32 inta_fh;
unsigned long flags;
#ifdef CONFIG_IWLWIFI_DEBUG
u32 inta_mask;
#endif
spin_lock_irqsave(&priv->lock, flags);
/* Ack/clear/reset pending uCode interrupts.
* Note: Some bits in CSR_INT are "OR" of bits in CSR_FH_INT_STATUS,
* and will clear only when CSR_FH_INT_STATUS gets cleared. */
inta = iwl_read32(priv, CSR_INT);
iwl_write32(priv, CSR_INT, inta);
/* Ack/clear/reset pending flow-handler (DMA) interrupts.
* Any new interrupts that happen after this, either while we're
* in this tasklet, or later, will show up in next ISR/tasklet. */
inta_fh = iwl_read32(priv, CSR_FH_INT_STATUS);
iwl_write32(priv, CSR_FH_INT_STATUS, inta_fh);
#ifdef CONFIG_IWLWIFI_DEBUG
if (priv->debug_level & IWL_DL_ISR) {
/* just for debug */
inta_mask = iwl_read32(priv, CSR_INT_MASK);
IWL_DEBUG_ISR("inta 0x%08x, enabled 0x%08x, fh 0x%08x\n",
inta, inta_mask, inta_fh);
}
#endif
/* Since CSR_INT and CSR_FH_INT_STATUS reads and clears are not
* atomic, make sure that inta covers all the interrupts that
* we've discovered, even if FH interrupt came in just after
* reading CSR_INT. */
if (inta_fh & CSR49_FH_INT_RX_MASK)
inta |= CSR_INT_BIT_FH_RX;
if (inta_fh & CSR49_FH_INT_TX_MASK)
inta |= CSR_INT_BIT_FH_TX;
/* Now service all interrupt bits discovered above. */
if (inta & CSR_INT_BIT_HW_ERR) {
IWL_ERROR("Microcode HW error detected. Restarting.\n");
/* Tell the device to stop sending interrupts */
iwl_disable_interrupts(priv);
iwl_irq_handle_error(priv);
handled |= CSR_INT_BIT_HW_ERR;
spin_unlock_irqrestore(&priv->lock, flags);
return;
}
#ifdef CONFIG_IWLWIFI_DEBUG
if (priv->debug_level & (IWL_DL_ISR)) {
/* NIC fires this, but we don't use it, redundant with WAKEUP */
if (inta & CSR_INT_BIT_SCD)
IWL_DEBUG_ISR("Scheduler finished to transmit "
"the frame/frames.\n");
/* Alive notification via Rx interrupt will do the real work */
if (inta & CSR_INT_BIT_ALIVE)
IWL_DEBUG_ISR("Alive interrupt\n");
}
#endif
/* Safely ignore these bits for debug checks below */
inta &= ~(CSR_INT_BIT_SCD | CSR_INT_BIT_ALIVE);
/* HW RF KILL switch toggled */
if (inta & CSR_INT_BIT_RF_KILL) {
int hw_rf_kill = 0;
if (!(iwl_read32(priv, CSR_GP_CNTRL) &
CSR_GP_CNTRL_REG_FLAG_HW_RF_KILL_SW))
hw_rf_kill = 1;
IWL_DEBUG(IWL_DL_RF_KILL, "RF_KILL bit toggled to %s.\n",
hw_rf_kill ? "disable radio" : "enable radio");
/* driver only loads ucode once setting the interface up.
* the driver as well won't allow loading if RFKILL is set
* therefore no need to restart the driver from this handler
*/
if (!hw_rf_kill && !test_bit(STATUS_ALIVE, &priv->status))
clear_bit(STATUS_RF_KILL_HW, &priv->status);
handled |= CSR_INT_BIT_RF_KILL;
}
/* Chip got too hot and stopped itself */
if (inta & CSR_INT_BIT_CT_KILL) {
IWL_ERROR("Microcode CT kill error detected.\n");
handled |= CSR_INT_BIT_CT_KILL;
}
/* Error detected by uCode */
if (inta & CSR_INT_BIT_SW_ERR) {
IWL_ERROR("Microcode SW error detected. Restarting 0x%X.\n",
inta);
iwl_irq_handle_error(priv);
handled |= CSR_INT_BIT_SW_ERR;
}
/* uCode wakes up after power-down sleep */
if (inta & CSR_INT_BIT_WAKEUP) {
IWL_DEBUG_ISR("Wakeup interrupt\n");
iwl_rx_queue_update_write_ptr(priv, &priv->rxq);
iwl_txq_update_write_ptr(priv, &priv->txq[0]);
iwl_txq_update_write_ptr(priv, &priv->txq[1]);
iwl_txq_update_write_ptr(priv, &priv->txq[2]);
iwl_txq_update_write_ptr(priv, &priv->txq[3]);
iwl_txq_update_write_ptr(priv, &priv->txq[4]);
iwl_txq_update_write_ptr(priv, &priv->txq[5]);
handled |= CSR_INT_BIT_WAKEUP;
}
/* All uCode command responses, including Tx command responses,
* Rx "responses" (frame-received notification), and other
* notifications from uCode come through here*/
if (inta & (CSR_INT_BIT_FH_RX | CSR_INT_BIT_SW_RX)) {
iwl_rx_handle(priv);
handled |= (CSR_INT_BIT_FH_RX | CSR_INT_BIT_SW_RX);
}
if (inta & CSR_INT_BIT_FH_TX) {
IWL_DEBUG_ISR("Tx interrupt\n");
handled |= CSR_INT_BIT_FH_TX;
/* FH finished to write, send event */
priv->ucode_write_complete = 1;
wake_up_interruptible(&priv->wait_command_queue);
}
if (inta & ~handled)
IWL_ERROR("Unhandled INTA bits 0x%08x\n", inta & ~handled);
if (inta & ~CSR_INI_SET_MASK) {
IWL_WARNING("Disabled INTA bits 0x%08x were pending\n",
inta & ~CSR_INI_SET_MASK);
IWL_WARNING(" with FH_INT = 0x%08x\n", inta_fh);
}
/* Re-enable all interrupts */
/* only Re-enable if diabled by irq */
if (test_bit(STATUS_INT_ENABLED, &priv->status))
iwl_enable_interrupts(priv);
#ifdef CONFIG_IWLWIFI_DEBUG
if (priv->debug_level & (IWL_DL_ISR)) {
inta = iwl_read32(priv, CSR_INT);
inta_mask = iwl_read32(priv, CSR_INT_MASK);
inta_fh = iwl_read32(priv, CSR_FH_INT_STATUS);
IWL_DEBUG_ISR("End inta 0x%08x, enabled 0x%08x, fh 0x%08x, "
"flags 0x%08lx\n", inta, inta_mask, inta_fh, flags);
}
#endif
spin_unlock_irqrestore(&priv->lock, flags);
}
static irqreturn_t iwl_isr(int irq, void *data)
{
struct iwl_priv *priv = data;
u32 inta, inta_mask;
u32 inta_fh;
if (!priv)
return IRQ_NONE;
spin_lock(&priv->lock);
/* Disable (but don't clear!) interrupts here to avoid
* back-to-back ISRs and sporadic interrupts from our NIC.
* If we have something to service, the tasklet will re-enable ints.
* If we *don't* have something, we'll re-enable before leaving here. */
inta_mask = iwl_read32(priv, CSR_INT_MASK); /* just for debug */
iwl_write32(priv, CSR_INT_MASK, 0x00000000);
/* Discover which interrupts are active/pending */
inta = iwl_read32(priv, CSR_INT);
inta_fh = iwl_read32(priv, CSR_FH_INT_STATUS);
/* Ignore interrupt if there's nothing in NIC to service.
* This may be due to IRQ shared with another device,
* or due to sporadic interrupts thrown from our NIC. */
if (!inta && !inta_fh) {
IWL_DEBUG_ISR("Ignore interrupt, inta == 0, inta_fh == 0\n");
goto none;
}
if ((inta == 0xFFFFFFFF) || ((inta & 0xFFFFFFF0) == 0xa5a5a5a0)) {
/* Hardware disappeared. It might have already raised
* an interrupt */
IWL_WARNING("HARDWARE GONE?? INTA == 0x%080x\n", inta);
goto unplugged;
}
IWL_DEBUG_ISR("ISR inta 0x%08x, enabled 0x%08x, fh 0x%08x\n",
inta, inta_mask, inta_fh);
inta &= ~CSR_INT_BIT_SCD;
/* iwl_irq_tasklet() will service interrupts and re-enable them */
if (likely(inta || inta_fh))
tasklet_schedule(&priv->irq_tasklet);
unplugged:
spin_unlock(&priv->lock);
return IRQ_HANDLED;
none:
/* re-enable interrupts here since we don't have anything to service. */
/* only Re-enable if diabled by irq */
if (test_bit(STATUS_INT_ENABLED, &priv->status))
iwl_enable_interrupts(priv);
spin_unlock(&priv->lock);
return IRQ_NONE;
}
/******************************************************************************
*
* uCode download functions
*
******************************************************************************/
static void iwl_dealloc_ucode_pci(struct iwl_priv *priv)
{
iwl_free_fw_desc(priv->pci_dev, &priv->ucode_code);
iwl_free_fw_desc(priv->pci_dev, &priv->ucode_data);
iwl_free_fw_desc(priv->pci_dev, &priv->ucode_data_backup);
iwl_free_fw_desc(priv->pci_dev, &priv->ucode_init);
iwl_free_fw_desc(priv->pci_dev, &priv->ucode_init_data);
iwl_free_fw_desc(priv->pci_dev, &priv->ucode_boot);
}
static void iwl_nic_start(struct iwl_priv *priv)
{
/* Remove all resets to allow NIC to operate */
iwl_write32(priv, CSR_RESET, 0);
}
/**
* iwl_read_ucode - Read uCode images from disk file.
*
* Copy into buffers for card to fetch via bus-mastering
*/
static int iwl_read_ucode(struct iwl_priv *priv)
{
struct iwl_ucode *ucode;
int ret;
const struct firmware *ucode_raw;
const char *name = priv->cfg->fw_name;
u8 *src;
size_t len;
u32 ver, inst_size, data_size, init_size, init_data_size, boot_size;
/* Ask kernel firmware_class module to get the boot firmware off disk.
* request_firmware() is synchronous, file is in memory on return. */
ret = request_firmware(&ucode_raw, name, &priv->pci_dev->dev);
if (ret < 0) {
IWL_ERROR("%s firmware file req failed: Reason %d\n",
name, ret);
goto error;
}
IWL_DEBUG_INFO("Got firmware '%s' file (%zd bytes) from disk\n",
name, ucode_raw->size);
/* Make sure that we got at least our header! */
if (ucode_raw->size < sizeof(*ucode)) {
IWL_ERROR("File size way too small!\n");
ret = -EINVAL;
goto err_release;
}
/* Data from ucode file: header followed by uCode images */
ucode = (void *)ucode_raw->data;
ver = le32_to_cpu(ucode->ver);
inst_size = le32_to_cpu(ucode->inst_size);
data_size = le32_to_cpu(ucode->data_size);
init_size = le32_to_cpu(ucode->init_size);
init_data_size = le32_to_cpu(ucode->init_data_size);
boot_size = le32_to_cpu(ucode->boot_size);
IWL_DEBUG_INFO("f/w package hdr ucode version = 0x%x\n", ver);
IWL_DEBUG_INFO("f/w package hdr runtime inst size = %u\n",
inst_size);
IWL_DEBUG_INFO("f/w package hdr runtime data size = %u\n",
data_size);
IWL_DEBUG_INFO("f/w package hdr init inst size = %u\n",
init_size);
IWL_DEBUG_INFO("f/w package hdr init data size = %u\n",
init_data_size);
IWL_DEBUG_INFO("f/w package hdr boot inst size = %u\n",
boot_size);
/* Verify size of file vs. image size info in file's header */
if (ucode_raw->size < sizeof(*ucode) +
inst_size + data_size + init_size +
init_data_size + boot_size) {
IWL_DEBUG_INFO("uCode file size %d too small\n",
(int)ucode_raw->size);
ret = -EINVAL;
goto err_release;
}
/* Verify that uCode images will fit in card's SRAM */
if (inst_size > priv->hw_params.max_inst_size) {
IWL_DEBUG_INFO("uCode instr len %d too large to fit in\n",
inst_size);
ret = -EINVAL;
goto err_release;
}
if (data_size > priv->hw_params.max_data_size) {
IWL_DEBUG_INFO("uCode data len %d too large to fit in\n",
data_size);
ret = -EINVAL;
goto err_release;
}
if (init_size > priv->hw_params.max_inst_size) {
IWL_DEBUG_INFO
("uCode init instr len %d too large to fit in\n",
init_size);
ret = -EINVAL;
goto err_release;
}
if (init_data_size > priv->hw_params.max_data_size) {
IWL_DEBUG_INFO
("uCode init data len %d too large to fit in\n",
init_data_size);
ret = -EINVAL;
goto err_release;
}
if (boot_size > priv->hw_params.max_bsm_size) {
IWL_DEBUG_INFO
("uCode boot instr len %d too large to fit in\n",
boot_size);
ret = -EINVAL;
goto err_release;
}
/* Allocate ucode buffers for card's bus-master loading ... */
/* Runtime instructions and 2 copies of data:
* 1) unmodified from disk
* 2) backup cache for save/restore during power-downs */
priv->ucode_code.len = inst_size;
iwl_alloc_fw_desc(priv->pci_dev, &priv->ucode_code);
priv->ucode_data.len = data_size;
iwl_alloc_fw_desc(priv->pci_dev, &priv->ucode_data);
priv->ucode_data_backup.len = data_size;
iwl_alloc_fw_desc(priv->pci_dev, &priv->ucode_data_backup);
/* Initialization instructions and data */
if (init_size && init_data_size) {
priv->ucode_init.len = init_size;
iwl_alloc_fw_desc(priv->pci_dev, &priv->ucode_init);
priv->ucode_init_data.len = init_data_size;
iwl_alloc_fw_desc(priv->pci_dev, &priv->ucode_init_data);
if (!priv->ucode_init.v_addr || !priv->ucode_init_data.v_addr)
goto err_pci_alloc;
}
/* Bootstrap (instructions only, no data) */
if (boot_size) {
priv->ucode_boot.len = boot_size;
iwl_alloc_fw_desc(priv->pci_dev, &priv->ucode_boot);
if (!priv->ucode_boot.v_addr)
goto err_pci_alloc;
}
/* Copy images into buffers for card's bus-master reads ... */
/* Runtime instructions (first block of data in file) */
src = &ucode->data[0];
len = priv->ucode_code.len;
IWL_DEBUG_INFO("Copying (but not loading) uCode instr len %Zd\n", len);
memcpy(priv->ucode_code.v_addr, src, len);
IWL_DEBUG_INFO("uCode instr buf vaddr = 0x%p, paddr = 0x%08x\n",
priv->ucode_code.v_addr, (u32)priv->ucode_code.p_addr);
/* Runtime data (2nd block)
* NOTE: Copy into backup buffer will be done in iwl_up() */
src = &ucode->data[inst_size];
len = priv->ucode_data.len;
IWL_DEBUG_INFO("Copying (but not loading) uCode data len %Zd\n", len);
memcpy(priv->ucode_data.v_addr, src, len);
memcpy(priv->ucode_data_backup.v_addr, src, len);
/* Initialization instructions (3rd block) */
if (init_size) {
src = &ucode->data[inst_size + data_size];
len = priv->ucode_init.len;
IWL_DEBUG_INFO("Copying (but not loading) init instr len %Zd\n",
len);
memcpy(priv->ucode_init.v_addr, src, len);
}
/* Initialization data (4th block) */
if (init_data_size) {
src = &ucode->data[inst_size + data_size + init_size];
len = priv->ucode_init_data.len;
IWL_DEBUG_INFO("Copying (but not loading) init data len %Zd\n",
len);
memcpy(priv->ucode_init_data.v_addr, src, len);
}
/* Bootstrap instructions (5th block) */
src = &ucode->data[inst_size + data_size + init_size + init_data_size];
len = priv->ucode_boot.len;
IWL_DEBUG_INFO("Copying (but not loading) boot instr len %Zd\n", len);
memcpy(priv->ucode_boot.v_addr, src, len);
/* We have our copies now, allow OS release its copies */
release_firmware(ucode_raw);
return 0;
err_pci_alloc:
IWL_ERROR("failed to allocate pci memory\n");
ret = -ENOMEM;
iwl_dealloc_ucode_pci(priv);
err_release:
release_firmware(ucode_raw);
error:
return ret;
}
/* temporary */
static int iwl_mac_beacon_update(struct ieee80211_hw *hw,
struct sk_buff *skb);
/**
* iwl_alive_start - called after REPLY_ALIVE notification received
* from protocol/runtime uCode (initialization uCode's
* Alive gets handled by iwl_init_alive_start()).
*/
static void iwl_alive_start(struct iwl_priv *priv)
{
int ret = 0;
IWL_DEBUG_INFO("Runtime Alive received.\n");
if (priv->card_alive.is_valid != UCODE_VALID_OK) {
/* We had an error bringing up the hardware, so take it
* all the way back down so we can try again */
IWL_DEBUG_INFO("Alive failed.\n");
goto restart;
}
/* Initialize uCode has loaded Runtime uCode ... verify inst image.
* This is a paranoid check, because we would not have gotten the
* "runtime" alive if code weren't properly loaded. */
if (iwl_verify_ucode(priv)) {
/* Runtime instruction load was bad;
* take it all the way back down so we can try again */
IWL_DEBUG_INFO("Bad runtime uCode load.\n");
goto restart;
}
iwl_clear_stations_table(priv);
ret = priv->cfg->ops->lib->alive_notify(priv);
if (ret) {
IWL_WARNING("Could not complete ALIVE transition [ntf]: %d\n",
ret);
goto restart;
}
/* After the ALIVE response, we can send host commands to the uCode */
set_bit(STATUS_ALIVE, &priv->status);
if (iwl_is_rfkill(priv))
return;
ieee80211_wake_queues(priv->hw);
priv->active_rate = priv->rates_mask;
priv->active_rate_basic = priv->rates_mask & IWL_BASIC_RATES_MASK;
if (iwl_is_associated(priv)) {
struct iwl_rxon_cmd *active_rxon =
(struct iwl_rxon_cmd *)&priv->active_rxon;
memcpy(&priv->staging_rxon, &priv->active_rxon,
sizeof(priv->staging_rxon));
active_rxon->filter_flags &= ~RXON_FILTER_ASSOC_MSK;
} else {
/* Initialize our rx_config data */
iwl_connection_init_rx_config(priv, priv->iw_mode);
memcpy(priv->staging_rxon.node_addr, priv->mac_addr, ETH_ALEN);
}
/* Configure Bluetooth device coexistence support */
iwl_send_bt_config(priv);
iwl_reset_run_time_calib(priv);
/* Configure the adapter for unassociated operation */
iwl_commit_rxon(priv);
/* At this point, the NIC is initialized and operational */
iwl_rf_kill_ct_config(priv);
iwl_leds_register(priv);
IWL_DEBUG_INFO("ALIVE processing complete.\n");
set_bit(STATUS_READY, &priv->status);
wake_up_interruptible(&priv->wait_command_queue);
if (priv->error_recovering)
iwl_error_recovery(priv);
iwl_power_update_mode(priv, 1);
/* reassociate for ADHOC mode */
if (priv->vif && (priv->iw_mode == NL80211_IFTYPE_ADHOC)) {
struct sk_buff *beacon = ieee80211_beacon_get(priv->hw,
priv->vif);
if (beacon)
iwl_mac_beacon_update(priv->hw, beacon);
}
if (test_and_clear_bit(STATUS_MODE_PENDING, &priv->status))
iwl_set_mode(priv, priv->iw_mode);
return;
restart:
queue_work(priv->workqueue, &priv->restart);
}
static void iwl_cancel_deferred_work(struct iwl_priv *priv);
static void __iwl_down(struct iwl_priv *priv)
{
unsigned long flags;
int exit_pending = test_bit(STATUS_EXIT_PENDING, &priv->status);
IWL_DEBUG_INFO(DRV_NAME " is going down\n");
if (!exit_pending)
set_bit(STATUS_EXIT_PENDING, &priv->status);
iwl_leds_unregister(priv);
iwl_clear_stations_table(priv);
/* Unblock any waiting calls */
wake_up_interruptible_all(&priv->wait_command_queue);
/* Wipe out the EXIT_PENDING status bit if we are not actually
* exiting the module */
if (!exit_pending)
clear_bit(STATUS_EXIT_PENDING, &priv->status);
/* stop and reset the on-board processor */
iwl_write32(priv, CSR_RESET, CSR_RESET_REG_FLAG_NEVO_RESET);
/* tell the device to stop sending interrupts */
spin_lock_irqsave(&priv->lock, flags);
iwl_disable_interrupts(priv);
spin_unlock_irqrestore(&priv->lock, flags);
iwl_synchronize_irq(priv);
if (priv->mac80211_registered)
ieee80211_stop_queues(priv->hw);
/* If we have not previously called iwl_init() then
* clear all bits but the RF Kill and SUSPEND bits and return */
if (!iwl_is_init(priv)) {
priv->status = test_bit(STATUS_RF_KILL_HW, &priv->status) <<
STATUS_RF_KILL_HW |
test_bit(STATUS_RF_KILL_SW, &priv->status) <<
STATUS_RF_KILL_SW |
test_bit(STATUS_GEO_CONFIGURED, &priv->status) <<
STATUS_GEO_CONFIGURED |
test_bit(STATUS_IN_SUSPEND, &priv->status) <<
STATUS_IN_SUSPEND |
test_bit(STATUS_EXIT_PENDING, &priv->status) <<
STATUS_EXIT_PENDING;
goto exit;
}
/* ...otherwise clear out all the status bits but the RF Kill and
* SUSPEND bits and continue taking the NIC down. */
priv->status &= test_bit(STATUS_RF_KILL_HW, &priv->status) <<
STATUS_RF_KILL_HW |
test_bit(STATUS_RF_KILL_SW, &priv->status) <<
STATUS_RF_KILL_SW |
test_bit(STATUS_GEO_CONFIGURED, &priv->status) <<
STATUS_GEO_CONFIGURED |
test_bit(STATUS_IN_SUSPEND, &priv->status) <<
STATUS_IN_SUSPEND |
test_bit(STATUS_FW_ERROR, &priv->status) <<
STATUS_FW_ERROR |
test_bit(STATUS_EXIT_PENDING, &priv->status) <<
STATUS_EXIT_PENDING;
spin_lock_irqsave(&priv->lock, flags);
iwl_clear_bit(priv, CSR_GP_CNTRL,
CSR_GP_CNTRL_REG_FLAG_MAC_ACCESS_REQ);
spin_unlock_irqrestore(&priv->lock, flags);
iwl_txq_ctx_stop(priv);
iwl_rxq_stop(priv);
spin_lock_irqsave(&priv->lock, flags);
if (!iwl_grab_nic_access(priv)) {
iwl_write_prph(priv, APMG_CLK_DIS_REG,
APMG_CLK_VAL_DMA_CLK_RQT);
iwl_release_nic_access(priv);
}
spin_unlock_irqrestore(&priv->lock, flags);
udelay(5);
/* FIXME: apm_ops.suspend(priv) */
if (exit_pending || test_bit(STATUS_IN_SUSPEND, &priv->status))
priv->cfg->ops->lib->apm_ops.stop(priv);
else
priv->cfg->ops->lib->apm_ops.reset(priv);
exit:
memset(&priv->card_alive, 0, sizeof(struct iwl_alive_resp));
if (priv->ibss_beacon)
dev_kfree_skb(priv->ibss_beacon);
priv->ibss_beacon = NULL;
/* clear out any free frames */
iwl_clear_free_frames(priv);
}
static void iwl_down(struct iwl_priv *priv)
{
mutex_lock(&priv->mutex);
__iwl_down(priv);
mutex_unlock(&priv->mutex);
iwl_cancel_deferred_work(priv);
}
#define MAX_HW_RESTARTS 5
static int __iwl_up(struct iwl_priv *priv)
{
int i;
int ret;
if (test_bit(STATUS_EXIT_PENDING, &priv->status)) {
IWL_WARNING("Exit pending; will not bring the NIC up\n");
return -EIO;
}
if (!priv->ucode_data_backup.v_addr || !priv->ucode_data.v_addr) {
IWL_ERROR("ucode not available for device bringup\n");
return -EIO;
}
/* If platform's RF_KILL switch is NOT set to KILL */
if (iwl_read32(priv, CSR_GP_CNTRL) & CSR_GP_CNTRL_REG_FLAG_HW_RF_KILL_SW)
clear_bit(STATUS_RF_KILL_HW, &priv->status);
else
set_bit(STATUS_RF_KILL_HW, &priv->status);
if (iwl_is_rfkill(priv)) {
iwl_enable_interrupts(priv);
IWL_WARNING("Radio disabled by %s RF Kill switch\n",
test_bit(STATUS_RF_KILL_HW, &priv->status) ? "HW" : "SW");
return 0;
}
iwl_write32(priv, CSR_INT, 0xFFFFFFFF);
ret = iwl_hw_nic_init(priv);
if (ret) {
IWL_ERROR("Unable to init nic\n");
return ret;
}
/* make sure rfkill handshake bits are cleared */
iwl_write32(priv, CSR_UCODE_DRV_GP1_CLR, CSR_UCODE_SW_BIT_RFKILL);
iwl_write32(priv, CSR_UCODE_DRV_GP1_CLR,
CSR_UCODE_DRV_GP1_BIT_CMD_BLOCKED);
/* clear (again), then enable host interrupts */
iwl_write32(priv, CSR_INT, 0xFFFFFFFF);
iwl_enable_interrupts(priv);
/* really make sure rfkill handshake bits are cleared */
iwl_write32(priv, CSR_UCODE_DRV_GP1_CLR, CSR_UCODE_SW_BIT_RFKILL);
iwl_write32(priv, CSR_UCODE_DRV_GP1_CLR, CSR_UCODE_SW_BIT_RFKILL);
/* Copy original ucode data image from disk into backup cache.
* This will be used to initialize the on-board processor's
* data SRAM for a clean start when the runtime program first loads. */
memcpy(priv->ucode_data_backup.v_addr, priv->ucode_data.v_addr,
priv->ucode_data.len);
for (i = 0; i < MAX_HW_RESTARTS; i++) {
iwl_clear_stations_table(priv);
/* load bootstrap state machine,
* load bootstrap program into processor's memory,
* prepare to load the "initialize" uCode */
ret = priv->cfg->ops->lib->load_ucode(priv);
if (ret) {
IWL_ERROR("Unable to set up bootstrap uCode: %d\n", ret);
continue;
}
/* Clear out the uCode error bit if it is set */
clear_bit(STATUS_FW_ERROR, &priv->status);
/* start card; "initialize" will load runtime ucode */
iwl_nic_start(priv);
IWL_DEBUG_INFO(DRV_NAME " is coming up\n");
return 0;
}
set_bit(STATUS_EXIT_PENDING, &priv->status);
__iwl_down(priv);
clear_bit(STATUS_EXIT_PENDING, &priv->status);
/* tried to restart and config the device for as long as our
* patience could withstand */
IWL_ERROR("Unable to initialize device after %d attempts.\n", i);
return -EIO;
}
/*****************************************************************************
*
* Workqueue callbacks
*
*****************************************************************************/
static void iwl_bg_init_alive_start(struct work_struct *data)
{
struct iwl_priv *priv =
container_of(data, struct iwl_priv, init_alive_start.work);
if (test_bit(STATUS_EXIT_PENDING, &priv->status))
return;
mutex_lock(&priv->mutex);
priv->cfg->ops->lib->init_alive_start(priv);
mutex_unlock(&priv->mutex);
}
static void iwl_bg_alive_start(struct work_struct *data)
{
struct iwl_priv *priv =
container_of(data, struct iwl_priv, alive_start.work);
if (test_bit(STATUS_EXIT_PENDING, &priv->status))
return;
mutex_lock(&priv->mutex);
iwl_alive_start(priv);
mutex_unlock(&priv->mutex);
}
static void iwl_bg_rf_kill(struct work_struct *work)
{
struct iwl_priv *priv = container_of(work, struct iwl_priv, rf_kill);
wake_up_interruptible(&priv->wait_command_queue);
if (test_bit(STATUS_EXIT_PENDING, &priv->status))
return;
mutex_lock(&priv->mutex);
if (!iwl_is_rfkill(priv)) {
IWL_DEBUG(IWL_DL_RF_KILL,
"HW and/or SW RF Kill no longer active, restarting "
"device\n");
if (!test_bit(STATUS_EXIT_PENDING, &priv->status))
queue_work(priv->workqueue, &priv->restart);
} else {
/* make sure mac80211 stop sending Tx frame */
if (priv->mac80211_registered)
ieee80211_stop_queues(priv->hw);
if (!test_bit(STATUS_RF_KILL_HW, &priv->status))
IWL_DEBUG_RF_KILL("Can not turn radio back on - "
"disabled by SW switch\n");
else
IWL_WARNING("Radio Frequency Kill Switch is On:\n"
"Kill switch must be turned off for "
"wireless networking to work.\n");
}
mutex_unlock(&priv->mutex);
iwl_rfkill_set_hw_state(priv);
}
static void iwl_bg_run_time_calib_work(struct work_struct *work)
{
struct iwl_priv *priv = container_of(work, struct iwl_priv,
run_time_calib_work);
mutex_lock(&priv->mutex);
if (test_bit(STATUS_EXIT_PENDING, &priv->status) ||
test_bit(STATUS_SCANNING, &priv->status)) {
mutex_unlock(&priv->mutex);
return;
}
if (priv->start_calib) {
iwl_chain_noise_calibration(priv, &priv->statistics);
iwl_sensitivity_calibration(priv, &priv->statistics);
}
mutex_unlock(&priv->mutex);
return;
}
static void iwl_bg_up(struct work_struct *data)
{
struct iwl_priv *priv = container_of(data, struct iwl_priv, up);
if (test_bit(STATUS_EXIT_PENDING, &priv->status))
return;
mutex_lock(&priv->mutex);
__iwl_up(priv);
mutex_unlock(&priv->mutex);
iwl_rfkill_set_hw_state(priv);
}
static void iwl_bg_restart(struct work_struct *data)
{
struct iwl_priv *priv = container_of(data, struct iwl_priv, restart);
if (test_bit(STATUS_EXIT_PENDING, &priv->status))
return;
iwl_down(priv);
queue_work(priv->workqueue, &priv->up);
}
static void iwl_bg_rx_replenish(struct work_struct *data)
{
struct iwl_priv *priv =
container_of(data, struct iwl_priv, rx_replenish);
if (test_bit(STATUS_EXIT_PENDING, &priv->status))
return;
mutex_lock(&priv->mutex);
iwl_rx_replenish(priv);
mutex_unlock(&priv->mutex);
}
#define IWL_DELAY_NEXT_SCAN (HZ*2)
static void iwl_post_associate(struct iwl_priv *priv)
{
struct ieee80211_conf *conf = NULL;
int ret = 0;
unsigned long flags;
if (priv->iw_mode == NL80211_IFTYPE_AP) {
IWL_ERROR("%s Should not be called in AP mode\n", __func__);
return;
}
IWL_DEBUG_ASSOC("Associated as %d to: %pM\n",
priv->assoc_id, priv->active_rxon.bssid_addr);
if (test_bit(STATUS_EXIT_PENDING, &priv->status))
return;
if (!priv->vif || !priv->is_open)
return;
iwl_power_cancel_timeout(priv);
iwl_scan_cancel_timeout(priv, 200);
conf = ieee80211_get_hw_conf(priv->hw);
priv->staging_rxon.filter_flags &= ~RXON_FILTER_ASSOC_MSK;
iwl_commit_rxon(priv);
iwl_setup_rxon_timing(priv);
ret = iwl_send_cmd_pdu(priv, REPLY_RXON_TIMING,
sizeof(priv->rxon_timing), &priv->rxon_timing);
if (ret)
IWL_WARNING("REPLY_RXON_TIMING failed - "
"Attempting to continue.\n");
priv->staging_rxon.filter_flags |= RXON_FILTER_ASSOC_MSK;
iwl_set_rxon_ht(priv, &priv->current_ht_config);
iwl_set_rxon_chain(priv);
priv->staging_rxon.assoc_id = cpu_to_le16(priv->assoc_id);
IWL_DEBUG_ASSOC("assoc id %d beacon interval %d\n",
priv->assoc_id, priv->beacon_int);
if (priv->assoc_capability & WLAN_CAPABILITY_SHORT_PREAMBLE)
priv->staging_rxon.flags |= RXON_FLG_SHORT_PREAMBLE_MSK;
else
priv->staging_rxon.flags &= ~RXON_FLG_SHORT_PREAMBLE_MSK;
if (priv->staging_rxon.flags & RXON_FLG_BAND_24G_MSK) {
if (priv->assoc_capability & WLAN_CAPABILITY_SHORT_SLOT_TIME)
priv->staging_rxon.flags |= RXON_FLG_SHORT_SLOT_MSK;
else
priv->staging_rxon.flags &= ~RXON_FLG_SHORT_SLOT_MSK;
if (priv->iw_mode == NL80211_IFTYPE_ADHOC)
priv->staging_rxon.flags &= ~RXON_FLG_SHORT_SLOT_MSK;
}
iwl_commit_rxon(priv);
switch (priv->iw_mode) {
case NL80211_IFTYPE_STATION:
break;
case NL80211_IFTYPE_ADHOC:
/* assume default assoc id */
priv->assoc_id = 1;
iwl_rxon_add_station(priv, priv->bssid, 0);
iwl_send_beacon_cmd(priv);
break;
default:
IWL_ERROR("%s Should not be called in %d mode\n",
__func__, priv->iw_mode);
break;
}
if (priv->iw_mode == NL80211_IFTYPE_ADHOC)
priv->assoc_station_added = 1;
spin_lock_irqsave(&priv->lock, flags);
iwl_activate_qos(priv, 0);
spin_unlock_irqrestore(&priv->lock, flags);
/* the chain noise calibration will enabled PM upon completion
* If chain noise has already been run, then we need to enable
* power management here */
if (priv->chain_noise_data.state == IWL_CHAIN_NOISE_DONE)
iwl_power_enable_management(priv);
/* Enable Rx differential gain and sensitivity calibrations */
iwl_chain_noise_reset(priv);
priv->start_calib = 1;
}
/*****************************************************************************
*
* mac80211 entry point functions
*
*****************************************************************************/
#define UCODE_READY_TIMEOUT (4 * HZ)
static int iwl_mac_start(struct ieee80211_hw *hw)
{
struct iwl_priv *priv = hw->priv;
int ret;
u16 pci_cmd;
IWL_DEBUG_MAC80211("enter\n");
if (pci_enable_device(priv->pci_dev)) {
IWL_ERROR("Fail to pci_enable_device\n");
return -ENODEV;
}
pci_restore_state(priv->pci_dev);
pci_enable_msi(priv->pci_dev);
/* enable interrupts if needed: hw bug w/a */
pci_read_config_word(priv->pci_dev, PCI_COMMAND, &pci_cmd);
if (pci_cmd & PCI_COMMAND_INTX_DISABLE) {
pci_cmd &= ~PCI_COMMAND_INTX_DISABLE;
pci_write_config_word(priv->pci_dev, PCI_COMMAND, pci_cmd);
}
ret = request_irq(priv->pci_dev->irq, iwl_isr, IRQF_SHARED,
DRV_NAME, priv);
if (ret) {
IWL_ERROR("Error allocating IRQ %d\n", priv->pci_dev->irq);
goto out_disable_msi;
}
/* we should be verifying the device is ready to be opened */
mutex_lock(&priv->mutex);
memset(&priv->staging_rxon, 0, sizeof(struct iwl_rxon_cmd));
/* fetch ucode file from disk, alloc and copy to bus-master buffers ...
* ucode filename and max sizes are card-specific. */
if (!priv->ucode_code.len) {
ret = iwl_read_ucode(priv);
if (ret) {
IWL_ERROR("Could not read microcode: %d\n", ret);
mutex_unlock(&priv->mutex);
goto out_release_irq;
}
}
ret = __iwl_up(priv);
mutex_unlock(&priv->mutex);
iwl_rfkill_set_hw_state(priv);
if (ret)
goto out_release_irq;
if (iwl_is_rfkill(priv))
goto out;
IWL_DEBUG_INFO("Start UP work done.\n");
if (test_bit(STATUS_IN_SUSPEND, &priv->status))
return 0;
/* Wait for START_ALIVE from Run Time ucode. Otherwise callbacks from
* mac80211 will not be run successfully. */
ret = wait_event_interruptible_timeout(priv->wait_command_queue,
test_bit(STATUS_READY, &priv->status),
UCODE_READY_TIMEOUT);
if (!ret) {
if (!test_bit(STATUS_READY, &priv->status)) {
IWL_ERROR("START_ALIVE timeout after %dms.\n",
jiffies_to_msecs(UCODE_READY_TIMEOUT));
ret = -ETIMEDOUT;
goto out_release_irq;
}
}
out:
priv->is_open = 1;
IWL_DEBUG_MAC80211("leave\n");
return 0;
out_release_irq:
free_irq(priv->pci_dev->irq, priv);
out_disable_msi:
pci_disable_msi(priv->pci_dev);
pci_disable_device(priv->pci_dev);
priv->is_open = 0;
IWL_DEBUG_MAC80211("leave - failed\n");
return ret;
}
static void iwl_mac_stop(struct ieee80211_hw *hw)
{
struct iwl_priv *priv = hw->priv;
IWL_DEBUG_MAC80211("enter\n");
if (!priv->is_open) {
IWL_DEBUG_MAC80211("leave - skip\n");
return;
}
priv->is_open = 0;
if (iwl_is_ready_rf(priv)) {
/* stop mac, cancel any scan request and clear
* RXON_FILTER_ASSOC_MSK BIT
*/
mutex_lock(&priv->mutex);
iwl_scan_cancel_timeout(priv, 100);
mutex_unlock(&priv->mutex);
}
iwl_down(priv);
flush_workqueue(priv->workqueue);
free_irq(priv->pci_dev->irq, priv);
pci_disable_msi(priv->pci_dev);
pci_save_state(priv->pci_dev);
pci_disable_device(priv->pci_dev);
IWL_DEBUG_MAC80211("leave\n");
}
static int iwl_mac_tx(struct ieee80211_hw *hw, struct sk_buff *skb)
{
struct iwl_priv *priv = hw->priv;
IWL_DEBUG_MACDUMP("enter\n");
IWL_DEBUG_TX("dev->xmit(%d bytes) at rate 0x%02x\n", skb->len,
ieee80211_get_tx_rate(hw, IEEE80211_SKB_CB(skb))->bitrate);
if (iwl_tx_skb(priv, skb))
dev_kfree_skb_any(skb);
IWL_DEBUG_MACDUMP("leave\n");
return 0;
}
static int iwl_mac_add_interface(struct ieee80211_hw *hw,
struct ieee80211_if_init_conf *conf)
{
struct iwl_priv *priv = hw->priv;
unsigned long flags;
IWL_DEBUG_MAC80211("enter: type %d\n", conf->type);
if (priv->vif) {
IWL_DEBUG_MAC80211("leave - vif != NULL\n");
return -EOPNOTSUPP;
}
spin_lock_irqsave(&priv->lock, flags);
priv->vif = conf->vif;
priv->iw_mode = conf->type;
spin_unlock_irqrestore(&priv->lock, flags);
mutex_lock(&priv->mutex);
if (conf->mac_addr) {
IWL_DEBUG_MAC80211("Set %pM\n", conf->mac_addr);
memcpy(priv->mac_addr, conf->mac_addr, ETH_ALEN);
}
if (iwl_set_mode(priv, conf->type) == -EAGAIN)
/* we are not ready, will run again when ready */
set_bit(STATUS_MODE_PENDING, &priv->status);
mutex_unlock(&priv->mutex);
IWL_DEBUG_MAC80211("leave\n");
return 0;
}
/**
* iwl_mac_config - mac80211 config callback
*
* We ignore conf->flags & IEEE80211_CONF_SHORT_SLOT_TIME since it seems to
* be set inappropriately and the driver currently sets the hardware up to
* use it whenever needed.
*/
static int iwl_mac_config(struct ieee80211_hw *hw, u32 changed)
{
struct iwl_priv *priv = hw->priv;
const struct iwl_channel_info *ch_info;
struct ieee80211_conf *conf = &hw->conf;
unsigned long flags;
int ret = 0;
u16 channel;
mutex_lock(&priv->mutex);
IWL_DEBUG_MAC80211("enter to channel %d\n", conf->channel->hw_value);
priv->current_ht_config.is_ht = conf->ht.enabled;
if (conf->radio_enabled && iwl_radio_kill_sw_enable_radio(priv)) {
IWL_DEBUG_MAC80211("leave - RF-KILL - waiting for uCode\n");
goto out;
}
if (!conf->radio_enabled)
iwl_radio_kill_sw_disable_radio(priv);
if (!iwl_is_ready(priv)) {
IWL_DEBUG_MAC80211("leave - not ready\n");
ret = -EIO;
goto out;
}
if (unlikely(!priv->cfg->mod_params->disable_hw_scan &&
test_bit(STATUS_SCANNING, &priv->status))) {
IWL_DEBUG_MAC80211("leave - scanning\n");
mutex_unlock(&priv->mutex);
return 0;
}
channel = ieee80211_frequency_to_channel(conf->channel->center_freq);
ch_info = iwl_get_channel_info(priv, conf->channel->band, channel);
if (!is_channel_valid(ch_info)) {
IWL_DEBUG_MAC80211("leave - invalid channel\n");
ret = -EINVAL;
goto out;
}
if (priv->iw_mode == NL80211_IFTYPE_ADHOC &&
!is_channel_ibss(ch_info)) {
IWL_ERROR("channel %d in band %d not IBSS channel\n",
conf->channel->hw_value, conf->channel->band);
ret = -EINVAL;
goto out;
}
spin_lock_irqsave(&priv->lock, flags);
/* if we are switching from ht to 2.4 clear flags
* from any ht related info since 2.4 does not
* support ht */
if ((le16_to_cpu(priv->staging_rxon.channel) != channel)
#ifdef IEEE80211_CONF_CHANNEL_SWITCH
&& !(conf->flags & IEEE80211_CONF_CHANNEL_SWITCH)
#endif
)
priv->staging_rxon.flags = 0;
iwl_set_rxon_channel(priv, conf->channel);
iwl_set_flags_for_band(priv, conf->channel->band);
/* The list of supported rates and rate mask can be different
* for each band; since the band may have changed, reset
* the rate mask to what mac80211 lists */
iwl_set_rate(priv);
spin_unlock_irqrestore(&priv->lock, flags);
#ifdef IEEE80211_CONF_CHANNEL_SWITCH
if (conf->flags & IEEE80211_CONF_CHANNEL_SWITCH) {
iwl_hw_channel_switch(priv, conf->channel);
goto out;
}
#endif
if (!conf->radio_enabled) {
IWL_DEBUG_MAC80211("leave - radio disabled\n");
goto out;
}
if (iwl_is_rfkill(priv)) {
IWL_DEBUG_MAC80211("leave - RF kill\n");
ret = -EIO;
goto out;
}
if (conf->flags & IEEE80211_CONF_PS)
ret = iwl_power_set_user_mode(priv, IWL_POWER_INDEX_3);
else
ret = iwl_power_set_user_mode(priv, IWL_POWER_MODE_CAM);
if (ret)
IWL_DEBUG_MAC80211("Error setting power level\n");
IWL_DEBUG_MAC80211("TX Power old=%d new=%d\n",
priv->tx_power_user_lmt, conf->power_level);
iwl_set_tx_power(priv, conf->power_level, false);
iwl_set_rate(priv);
if (memcmp(&priv->active_rxon,
&priv->staging_rxon, sizeof(priv->staging_rxon)))
iwl_commit_rxon(priv);
else
IWL_DEBUG_INFO("No re-sending same RXON configuration.\n");
IWL_DEBUG_MAC80211("leave\n");
out:
mutex_unlock(&priv->mutex);
return ret;
}
static void iwl_config_ap(struct iwl_priv *priv)
{
int ret = 0;
unsigned long flags;
if (test_bit(STATUS_EXIT_PENDING, &priv->status))
return;
/* The following should be done only at AP bring up */
if (!iwl_is_associated(priv)) {
/* RXON - unassoc (to set timing command) */
priv->staging_rxon.filter_flags &= ~RXON_FILTER_ASSOC_MSK;
iwl_commit_rxon(priv);
/* RXON Timing */
iwl_setup_rxon_timing(priv);
ret = iwl_send_cmd_pdu(priv, REPLY_RXON_TIMING,
sizeof(priv->rxon_timing), &priv->rxon_timing);
if (ret)
IWL_WARNING("REPLY_RXON_TIMING failed - "
"Attempting to continue.\n");
iwl_set_rxon_chain(priv);
/* FIXME: what should be the assoc_id for AP? */
priv->staging_rxon.assoc_id = cpu_to_le16(priv->assoc_id);
if (priv->assoc_capability & WLAN_CAPABILITY_SHORT_PREAMBLE)
priv->staging_rxon.flags |=
RXON_FLG_SHORT_PREAMBLE_MSK;
else
priv->staging_rxon.flags &=
~RXON_FLG_SHORT_PREAMBLE_MSK;
if (priv->staging_rxon.flags & RXON_FLG_BAND_24G_MSK) {
if (priv->assoc_capability &
WLAN_CAPABILITY_SHORT_SLOT_TIME)
priv->staging_rxon.flags |=
RXON_FLG_SHORT_SLOT_MSK;
else
priv->staging_rxon.flags &=
~RXON_FLG_SHORT_SLOT_MSK;
if (priv->iw_mode == NL80211_IFTYPE_ADHOC)
priv->staging_rxon.flags &=
~RXON_FLG_SHORT_SLOT_MSK;
}
/* restore RXON assoc */
priv->staging_rxon.filter_flags |= RXON_FILTER_ASSOC_MSK;
iwl_commit_rxon(priv);
spin_lock_irqsave(&priv->lock, flags);
iwl_activate_qos(priv, 1);
spin_unlock_irqrestore(&priv->lock, flags);
iwl_rxon_add_station(priv, iwl_bcast_addr, 0);
}
iwl_send_beacon_cmd(priv);
/* FIXME - we need to add code here to detect a totally new
* configuration, reset the AP, unassoc, rxon timing, assoc,
* clear sta table, add BCAST sta... */
}
static int iwl_mac_config_interface(struct ieee80211_hw *hw,
struct ieee80211_vif *vif,
struct ieee80211_if_conf *conf)
{
struct iwl_priv *priv = hw->priv;
int rc;
if (conf == NULL)
return -EIO;
if (priv->vif != vif) {
IWL_DEBUG_MAC80211("leave - priv->vif != vif\n");
return 0;
}
if (priv->iw_mode == NL80211_IFTYPE_ADHOC &&
conf->changed & IEEE80211_IFCC_BEACON) {
struct sk_buff *beacon = ieee80211_beacon_get(hw, vif);
if (!beacon)
return -ENOMEM;
mutex_lock(&priv->mutex);
rc = iwl_mac_beacon_update(hw, beacon);
mutex_unlock(&priv->mutex);
if (rc)
return rc;
}
if (!iwl_is_alive(priv))
return -EAGAIN;
mutex_lock(&priv->mutex);
if (conf->bssid)
IWL_DEBUG_MAC80211("bssid: %pM\n", conf->bssid);
/*
* very dubious code was here; the probe filtering flag is never set:
*
if (unlikely(test_bit(STATUS_SCANNING, &priv->status)) &&
!(priv->hw->flags & IEEE80211_HW_NO_PROBE_FILTERING)) {
*/
if (priv->iw_mode == NL80211_IFTYPE_AP) {
if (!conf->bssid) {
conf->bssid = priv->mac_addr;
memcpy(priv->bssid, priv->mac_addr, ETH_ALEN);
IWL_DEBUG_MAC80211("bssid was set to: %pM\n",
conf->bssid);
}
if (priv->ibss_beacon)
dev_kfree_skb(priv->ibss_beacon);
priv->ibss_beacon = ieee80211_beacon_get(hw, vif);
}
if (iwl_is_rfkill(priv))
goto done;
if (conf->bssid && !is_zero_ether_addr(conf->bssid) &&
!is_multicast_ether_addr(conf->bssid)) {
/* If there is currently a HW scan going on in the background
* then we need to cancel it else the RXON below will fail. */
if (iwl_scan_cancel_timeout(priv, 100)) {
IWL_WARNING("Aborted scan still in progress "
"after 100ms\n");
IWL_DEBUG_MAC80211("leaving - scan abort failed.\n");
mutex_unlock(&priv->mutex);
return -EAGAIN;
}
memcpy(priv->staging_rxon.bssid_addr, conf->bssid, ETH_ALEN);
/* TODO: Audit driver for usage of these members and see
* if mac80211 deprecates them (priv->bssid looks like it
* shouldn't be there, but I haven't scanned the IBSS code
* to verify) - jpk */
memcpy(priv->bssid, conf->bssid, ETH_ALEN);
if (priv->iw_mode == NL80211_IFTYPE_AP)
iwl_config_ap(priv);
else {
rc = iwl_commit_rxon(priv);
if ((priv->iw_mode == NL80211_IFTYPE_STATION) && rc)
iwl_rxon_add_station(
priv, priv->active_rxon.bssid_addr, 1);
}
} else {
iwl_scan_cancel_timeout(priv, 100);
priv->staging_rxon.filter_flags &= ~RXON_FILTER_ASSOC_MSK;
iwl_commit_rxon(priv);
}
done:
IWL_DEBUG_MAC80211("leave\n");
mutex_unlock(&priv->mutex);
return 0;
}
static void iwl_configure_filter(struct ieee80211_hw *hw,
unsigned int changed_flags,
unsigned int *total_flags,
int mc_count, struct dev_addr_list *mc_list)
{
struct iwl_priv *priv = hw->priv;
__le32 *filter_flags = &priv->staging_rxon.filter_flags;
IWL_DEBUG_MAC80211("Enter: changed: 0x%x, total: 0x%x\n",
changed_flags, *total_flags);
if (changed_flags & (FIF_OTHER_BSS | FIF_PROMISC_IN_BSS)) {
if (*total_flags & (FIF_OTHER_BSS | FIF_PROMISC_IN_BSS))
*filter_flags |= RXON_FILTER_PROMISC_MSK;
else
*filter_flags &= ~RXON_FILTER_PROMISC_MSK;
}
if (changed_flags & FIF_ALLMULTI) {
if (*total_flags & FIF_ALLMULTI)
*filter_flags |= RXON_FILTER_ACCEPT_GRP_MSK;
else
*filter_flags &= ~RXON_FILTER_ACCEPT_GRP_MSK;
}
if (changed_flags & FIF_CONTROL) {
if (*total_flags & FIF_CONTROL)
*filter_flags |= RXON_FILTER_CTL2HOST_MSK;
else
*filter_flags &= ~RXON_FILTER_CTL2HOST_MSK;
}
if (changed_flags & FIF_BCN_PRBRESP_PROMISC) {
if (*total_flags & FIF_BCN_PRBRESP_PROMISC)
*filter_flags |= RXON_FILTER_BCON_AWARE_MSK;
else
*filter_flags &= ~RXON_FILTER_BCON_AWARE_MSK;
}
/* We avoid iwl_commit_rxon here to commit the new filter flags
* since mac80211 will call ieee80211_hw_config immediately.
* (mc_list is not supported at this time). Otherwise, we need to
* queue a background iwl_commit_rxon work.
*/
*total_flags &= FIF_OTHER_BSS | FIF_ALLMULTI | FIF_PROMISC_IN_BSS |
FIF_BCN_PRBRESP_PROMISC | FIF_CONTROL;
}
static void iwl_mac_remove_interface(struct ieee80211_hw *hw,
struct ieee80211_if_init_conf *conf)
{
struct iwl_priv *priv = hw->priv;
IWL_DEBUG_MAC80211("enter\n");
mutex_lock(&priv->mutex);
if (iwl_is_ready_rf(priv)) {
iwl_scan_cancel_timeout(priv, 100);
priv->staging_rxon.filter_flags &= ~RXON_FILTER_ASSOC_MSK;
iwl_commit_rxon(priv);
}
if (priv->vif == conf->vif) {
priv->vif = NULL;
memset(priv->bssid, 0, ETH_ALEN);
}
mutex_unlock(&priv->mutex);
IWL_DEBUG_MAC80211("leave\n");
}
#define IWL_DELAY_NEXT_SCAN_AFTER_ASSOC (HZ*6)
static void iwl_bss_info_changed(struct ieee80211_hw *hw,
struct ieee80211_vif *vif,
struct ieee80211_bss_conf *bss_conf,
u32 changes)
{
struct iwl_priv *priv = hw->priv;
IWL_DEBUG_MAC80211("changes = 0x%X\n", changes);
if (changes & BSS_CHANGED_ERP_PREAMBLE) {
IWL_DEBUG_MAC80211("ERP_PREAMBLE %d\n",
bss_conf->use_short_preamble);
if (bss_conf->use_short_preamble)
priv->staging_rxon.flags |= RXON_FLG_SHORT_PREAMBLE_MSK;
else
priv->staging_rxon.flags &= ~RXON_FLG_SHORT_PREAMBLE_MSK;
}
if (changes & BSS_CHANGED_ERP_CTS_PROT) {
IWL_DEBUG_MAC80211("ERP_CTS %d\n", bss_conf->use_cts_prot);
if (bss_conf->use_cts_prot && (priv->band != IEEE80211_BAND_5GHZ))
priv->staging_rxon.flags |= RXON_FLG_TGG_PROTECT_MSK;
else
priv->staging_rxon.flags &= ~RXON_FLG_TGG_PROTECT_MSK;
}
if (changes & BSS_CHANGED_HT) {
iwl_ht_conf(priv, bss_conf);
iwl_set_rxon_chain(priv);
}
if (changes & BSS_CHANGED_ASSOC) {
IWL_DEBUG_MAC80211("ASSOC %d\n", bss_conf->assoc);
/* This should never happen as this function should
* never be called from interrupt context. */
if (WARN_ON_ONCE(in_interrupt()))
return;
if (bss_conf->assoc) {
priv->assoc_id = bss_conf->aid;
priv->beacon_int = bss_conf->beacon_int;
priv->power_data.dtim_period = bss_conf->dtim_period;
priv->timestamp = bss_conf->timestamp;
priv->assoc_capability = bss_conf->assoc_capability;
/* we have just associated, don't start scan too early
* leave time for EAPOL exchange to complete
*/
priv->next_scan_jiffies = jiffies +
IWL_DELAY_NEXT_SCAN_AFTER_ASSOC;
mutex_lock(&priv->mutex);
iwl_post_associate(priv);
mutex_unlock(&priv->mutex);
} else {
priv->assoc_id = 0;
IWL_DEBUG_MAC80211("DISASSOC %d\n", bss_conf->assoc);
}
} else if (changes && iwl_is_associated(priv) && priv->assoc_id) {
IWL_DEBUG_MAC80211("Associated Changes %d\n", changes);
iwl_send_rxon_assoc(priv);
}
}
static int iwl_mac_hw_scan(struct ieee80211_hw *hw, u8 *ssid, size_t ssid_len)
{
unsigned long flags;
struct iwl_priv *priv = hw->priv;
int ret;
IWL_DEBUG_MAC80211("enter\n");
mutex_lock(&priv->mutex);
spin_lock_irqsave(&priv->lock, flags);
if (!iwl_is_ready_rf(priv)) {
ret = -EIO;
IWL_DEBUG_MAC80211("leave - not ready or exit pending\n");
goto out_unlock;
}
if (priv->iw_mode == NL80211_IFTYPE_AP) { /* APs don't scan */
ret = -EIO;
IWL_ERROR("ERROR: APs don't scan\n");
goto out_unlock;
}
/* We don't schedule scan within next_scan_jiffies period.
* Avoid scanning during possible EAPOL exchange, return
* success immediately.
*/
if (priv->next_scan_jiffies &&
time_after(priv->next_scan_jiffies, jiffies)) {
IWL_DEBUG_SCAN("scan rejected: within next scan period\n");
queue_work(priv->workqueue, &priv->scan_completed);
ret = 0;
goto out_unlock;
}
/* if we just finished scan ask for delay */
if (iwl_is_associated(priv) && priv->last_scan_jiffies &&
time_after(priv->last_scan_jiffies + IWL_DELAY_NEXT_SCAN, jiffies)) {
IWL_DEBUG_SCAN("scan rejected: within previous scan period\n");
queue_work(priv->workqueue, &priv->scan_completed);
ret = 0;
goto out_unlock;
}
if (ssid_len) {
priv->one_direct_scan = 1;
priv->direct_ssid_len = min_t(u8, ssid_len, IW_ESSID_MAX_SIZE);
memcpy(priv->direct_ssid, ssid, priv->direct_ssid_len);
} else {
priv->one_direct_scan = 0;
}
ret = iwl_scan_initiate(priv);
IWL_DEBUG_MAC80211("leave\n");
out_unlock:
spin_unlock_irqrestore(&priv->lock, flags);
mutex_unlock(&priv->mutex);
return ret;
}
static void iwl_mac_update_tkip_key(struct ieee80211_hw *hw,
struct ieee80211_key_conf *keyconf, const u8 *addr,
u32 iv32, u16 *phase1key)
{
struct iwl_priv *priv = hw->priv;
IWL_DEBUG_MAC80211("enter\n");
iwl_update_tkip_key(priv, keyconf, addr, iv32, phase1key);
IWL_DEBUG_MAC80211("leave\n");
}
static int iwl_mac_set_key(struct ieee80211_hw *hw, enum set_key_cmd cmd,
const u8 *local_addr, const u8 *addr,
struct ieee80211_key_conf *key)
{
struct iwl_priv *priv = hw->priv;
int ret = 0;
u8 sta_id = IWL_INVALID_STATION;
u8 is_default_wep_key = 0;
IWL_DEBUG_MAC80211("enter\n");
if (priv->hw_params.sw_crypto) {
IWL_DEBUG_MAC80211("leave - hwcrypto disabled\n");
return -EOPNOTSUPP;
}
if (is_zero_ether_addr(addr))
/* only support pairwise keys */
return -EOPNOTSUPP;
sta_id = iwl_find_station(priv, addr);
if (sta_id == IWL_INVALID_STATION) {
IWL_DEBUG_MAC80211("leave - %pM not in station map.\n",
addr);
return -EINVAL;
}
mutex_lock(&priv->mutex);
iwl_scan_cancel_timeout(priv, 100);
mutex_unlock(&priv->mutex);
/* If we are getting WEP group key and we didn't receive any key mapping
* so far, we are in legacy wep mode (group key only), otherwise we are
* in 1X mode.
* In legacy wep mode, we use another host command to the uCode */
if (key->alg == ALG_WEP && sta_id == priv->hw_params.bcast_sta_id &&
priv->iw_mode != NL80211_IFTYPE_AP) {
if (cmd == SET_KEY)
is_default_wep_key = !priv->key_mapping_key;
else
is_default_wep_key =
(key->hw_key_idx == HW_KEY_DEFAULT);
}
switch (cmd) {
case SET_KEY:
if (is_default_wep_key)
ret = iwl_set_default_wep_key(priv, key);
else
ret = iwl_set_dynamic_key(priv, key, sta_id);
IWL_DEBUG_MAC80211("enable hwcrypto key\n");
break;
case DISABLE_KEY:
if (is_default_wep_key)
ret = iwl_remove_default_wep_key(priv, key);
else
ret = iwl_remove_dynamic_key(priv, key, sta_id);
IWL_DEBUG_MAC80211("disable hwcrypto key\n");
break;
default:
ret = -EINVAL;
}
IWL_DEBUG_MAC80211("leave\n");
return ret;
}
static int iwl_mac_conf_tx(struct ieee80211_hw *hw, u16 queue,
const struct ieee80211_tx_queue_params *params)
{
struct iwl_priv *priv = hw->priv;
unsigned long flags;
int q;
IWL_DEBUG_MAC80211("enter\n");
if (!iwl_is_ready_rf(priv)) {
IWL_DEBUG_MAC80211("leave - RF not ready\n");
return -EIO;
}
if (queue >= AC_NUM) {
IWL_DEBUG_MAC80211("leave - queue >= AC_NUM %d\n", queue);
return 0;
}
if (!priv->qos_data.qos_enable) {
priv->qos_data.qos_active = 0;
IWL_DEBUG_MAC80211("leave - qos not enabled\n");
return 0;
}
q = AC_NUM - 1 - queue;
spin_lock_irqsave(&priv->lock, flags);
priv->qos_data.def_qos_parm.ac[q].cw_min = cpu_to_le16(params->cw_min);
priv->qos_data.def_qos_parm.ac[q].cw_max = cpu_to_le16(params->cw_max);
priv->qos_data.def_qos_parm.ac[q].aifsn = params->aifs;
priv->qos_data.def_qos_parm.ac[q].edca_txop =
cpu_to_le16((params->txop * 32));
priv->qos_data.def_qos_parm.ac[q].reserved1 = 0;
priv->qos_data.qos_active = 1;
if (priv->iw_mode == NL80211_IFTYPE_AP)
iwl_activate_qos(priv, 1);
else if (priv->assoc_id && iwl_is_associated(priv))
iwl_activate_qos(priv, 0);
spin_unlock_irqrestore(&priv->lock, flags);
IWL_DEBUG_MAC80211("leave\n");
return 0;
}
static int iwl_mac_ampdu_action(struct ieee80211_hw *hw,
enum ieee80211_ampdu_mlme_action action,
struct ieee80211_sta *sta, u16 tid, u16 *ssn)
{
struct iwl_priv *priv = hw->priv;
IWL_DEBUG_HT("A-MPDU action on addr %pM tid %d\n",
sta->addr, tid);
if (!(priv->cfg->sku & IWL_SKU_N))
return -EACCES;
switch (action) {
case IEEE80211_AMPDU_RX_START:
IWL_DEBUG_HT("start Rx\n");
return iwl_sta_rx_agg_start(priv, sta->addr, tid, *ssn);
case IEEE80211_AMPDU_RX_STOP:
IWL_DEBUG_HT("stop Rx\n");
return iwl_sta_rx_agg_stop(priv, sta->addr, tid);
case IEEE80211_AMPDU_TX_START:
IWL_DEBUG_HT("start Tx\n");
return iwl_tx_agg_start(priv, sta->addr, tid, ssn);
case IEEE80211_AMPDU_TX_STOP:
IWL_DEBUG_HT("stop Tx\n");
return iwl_tx_agg_stop(priv, sta->addr, tid);
default:
IWL_DEBUG_HT("unknown\n");
return -EINVAL;
break;
}
return 0;
}
static int iwl_mac_get_tx_stats(struct ieee80211_hw *hw,
struct ieee80211_tx_queue_stats *stats)
{
struct iwl_priv *priv = hw->priv;
int i, avail;
struct iwl_tx_queue *txq;
struct iwl_queue *q;
unsigned long flags;
IWL_DEBUG_MAC80211("enter\n");
if (!iwl_is_ready_rf(priv)) {
IWL_DEBUG_MAC80211("leave - RF not ready\n");
return -EIO;
}
spin_lock_irqsave(&priv->lock, flags);
for (i = 0; i < AC_NUM; i++) {
txq = &priv->txq[i];
q = &txq->q;
avail = iwl_queue_space(q);
stats[i].len = q->n_window - avail;
stats[i].limit = q->n_window - q->high_mark;
stats[i].count = q->n_window;
}
spin_unlock_irqrestore(&priv->lock, flags);
IWL_DEBUG_MAC80211("leave\n");
return 0;
}
static int iwl_mac_get_stats(struct ieee80211_hw *hw,
struct ieee80211_low_level_stats *stats)
{
struct iwl_priv *priv = hw->priv;
priv = hw->priv;
IWL_DEBUG_MAC80211("enter\n");
IWL_DEBUG_MAC80211("leave\n");
return 0;
}
static void iwl_mac_reset_tsf(struct ieee80211_hw *hw)
{
struct iwl_priv *priv = hw->priv;
unsigned long flags;
mutex_lock(&priv->mutex);
IWL_DEBUG_MAC80211("enter\n");
spin_lock_irqsave(&priv->lock, flags);
memset(&priv->current_ht_config, 0, sizeof(struct iwl_ht_info));
spin_unlock_irqrestore(&priv->lock, flags);
iwl_reset_qos(priv);
spin_lock_irqsave(&priv->lock, flags);
priv->assoc_id = 0;
priv->assoc_capability = 0;
priv->assoc_station_added = 0;
/* new association get rid of ibss beacon skb */
if (priv->ibss_beacon)
dev_kfree_skb(priv->ibss_beacon);
priv->ibss_beacon = NULL;
priv->beacon_int = priv->hw->conf.beacon_int;
priv->timestamp = 0;
if ((priv->iw_mode == NL80211_IFTYPE_STATION))
priv->beacon_int = 0;
spin_unlock_irqrestore(&priv->lock, flags);
if (!iwl_is_ready_rf(priv)) {
IWL_DEBUG_MAC80211("leave - not ready\n");
mutex_unlock(&priv->mutex);
return;
}
/* we are restarting association process
* clear RXON_FILTER_ASSOC_MSK bit
*/
if (priv->iw_mode != NL80211_IFTYPE_AP) {
iwl_scan_cancel_timeout(priv, 100);
priv->staging_rxon.filter_flags &= ~RXON_FILTER_ASSOC_MSK;
iwl_commit_rxon(priv);
}
iwl_power_update_mode(priv, 0);
/* Per mac80211.h: This is only used in IBSS mode... */
if (priv->iw_mode != NL80211_IFTYPE_ADHOC) {
/* switch to CAM during association period.
* the ucode will block any association/authentication
* frome during assiciation period if it can not hear
* the AP because of PM. the timer enable PM back is
* association do not complete
*/
if (priv->hw->conf.channel->flags & (IEEE80211_CHAN_PASSIVE_SCAN |
IEEE80211_CHAN_RADAR))
iwl_power_disable_management(priv, 3000);
IWL_DEBUG_MAC80211("leave - not in IBSS\n");
mutex_unlock(&priv->mutex);
return;
}
iwl_set_rate(priv);
mutex_unlock(&priv->mutex);
IWL_DEBUG_MAC80211("leave\n");
}
static int iwl_mac_beacon_update(struct ieee80211_hw *hw, struct sk_buff *skb)
{
struct iwl_priv *priv = hw->priv;
unsigned long flags;
__le64 timestamp;
IWL_DEBUG_MAC80211("enter\n");
if (!iwl_is_ready_rf(priv)) {
IWL_DEBUG_MAC80211("leave - RF not ready\n");
return -EIO;
}
if (priv->iw_mode != NL80211_IFTYPE_ADHOC) {
IWL_DEBUG_MAC80211("leave - not IBSS\n");
return -EIO;
}
spin_lock_irqsave(&priv->lock, flags);
if (priv->ibss_beacon)
dev_kfree_skb(priv->ibss_beacon);
priv->ibss_beacon = skb;
priv->assoc_id = 0;
timestamp = ((struct ieee80211_mgmt *)skb->data)->u.beacon.timestamp;
priv->timestamp = le64_to_cpu(timestamp);
IWL_DEBUG_MAC80211("leave\n");
spin_unlock_irqrestore(&priv->lock, flags);
iwl_reset_qos(priv);
iwl_post_associate(priv);
return 0;
}
/*****************************************************************************
*
* sysfs attributes
*
*****************************************************************************/
#ifdef CONFIG_IWLWIFI_DEBUG
/*
* The following adds a new attribute to the sysfs representation
* of this device driver (i.e. a new file in /sys/bus/pci/drivers/iwl/)
* used for controlling the debug level.
*
* See the level definitions in iwl for details.
*/
static ssize_t show_debug_level(struct device *d,
struct device_attribute *attr, char *buf)
{
struct iwl_priv *priv = d->driver_data;
return sprintf(buf, "0x%08X\n", priv->debug_level);
}
static ssize_t store_debug_level(struct device *d,
struct device_attribute *attr,
const char *buf, size_t count)
{
struct iwl_priv *priv = d->driver_data;
unsigned long val;
int ret;
ret = strict_strtoul(buf, 0, &val);
if (ret)
printk(KERN_INFO DRV_NAME
": %s is not in hex or decimal form.\n", buf);
else
priv->debug_level = val;
return strnlen(buf, count);
}
static DEVICE_ATTR(debug_level, S_IWUSR | S_IRUGO,
show_debug_level, store_debug_level);
#endif /* CONFIG_IWLWIFI_DEBUG */
static ssize_t show_version(struct device *d,
struct device_attribute *attr, char *buf)
{
struct iwl_priv *priv = d->driver_data;
struct iwl_alive_resp *palive = &priv->card_alive;
ssize_t pos = 0;
u16 eeprom_ver;
if (palive->is_valid)
pos += sprintf(buf + pos,
"fw version: 0x%01X.0x%01X.0x%01X.0x%01X\n"
"fw type: 0x%01X 0x%01X\n",
palive->ucode_major, palive->ucode_minor,
palive->sw_rev[0], palive->sw_rev[1],
palive->ver_type, palive->ver_subtype);
else
pos += sprintf(buf + pos, "fw not loaded\n");
if (priv->eeprom) {
eeprom_ver = iwl_eeprom_query16(priv, EEPROM_VERSION);
pos += sprintf(buf + pos, "EEPROM version: 0x%x\n",
eeprom_ver);
} else {
pos += sprintf(buf + pos, "EEPROM not initialzed\n");
}
return pos;
}
static DEVICE_ATTR(version, S_IWUSR | S_IRUGO, show_version, NULL);
static ssize_t show_temperature(struct device *d,
struct device_attribute *attr, char *buf)
{
struct iwl_priv *priv = (struct iwl_priv *)d->driver_data;
if (!iwl_is_alive(priv))
return -EAGAIN;
return sprintf(buf, "%d\n", priv->temperature);
}
static DEVICE_ATTR(temperature, S_IRUGO, show_temperature, NULL);
static ssize_t show_tx_power(struct device *d,
struct device_attribute *attr, char *buf)
{
struct iwl_priv *priv = (struct iwl_priv *)d->driver_data;
return sprintf(buf, "%d\n", priv->tx_power_user_lmt);
}
static ssize_t store_tx_power(struct device *d,
struct device_attribute *attr,
const char *buf, size_t count)
{
struct iwl_priv *priv = (struct iwl_priv *)d->driver_data;
unsigned long val;
int ret;
ret = strict_strtoul(buf, 10, &val);
if (ret)
printk(KERN_INFO DRV_NAME
": %s is not in decimal form.\n", buf);
else
iwl_set_tx_power(priv, val, false);
return count;
}
static DEVICE_ATTR(tx_power, S_IWUSR | S_IRUGO, show_tx_power, store_tx_power);
static ssize_t show_flags(struct device *d,
struct device_attribute *attr, char *buf)
{
struct iwl_priv *priv = (struct iwl_priv *)d->driver_data;
return sprintf(buf, "0x%04X\n", priv->active_rxon.flags);
}
static ssize_t store_flags(struct device *d,
struct device_attribute *attr,
const char *buf, size_t count)
{
struct iwl_priv *priv = (struct iwl_priv *)d->driver_data;
unsigned long val;
u32 flags;
int ret = strict_strtoul(buf, 0, &val);
if (ret)
return ret;
flags = (u32)val;
mutex_lock(&priv->mutex);
if (le32_to_cpu(priv->staging_rxon.flags) != flags) {
/* Cancel any currently running scans... */
if (iwl_scan_cancel_timeout(priv, 100))
IWL_WARNING("Could not cancel scan.\n");
else {
IWL_DEBUG_INFO("Commit rxon.flags = 0x%04X\n", flags);
priv->staging_rxon.flags = cpu_to_le32(flags);
iwl_commit_rxon(priv);
}
}
mutex_unlock(&priv->mutex);
return count;
}
static DEVICE_ATTR(flags, S_IWUSR | S_IRUGO, show_flags, store_flags);
static ssize_t show_filter_flags(struct device *d,
struct device_attribute *attr, char *buf)
{
struct iwl_priv *priv = (struct iwl_priv *)d->driver_data;
return sprintf(buf, "0x%04X\n",
le32_to_cpu(priv->active_rxon.filter_flags));
}
static ssize_t store_filter_flags(struct device *d,
struct device_attribute *attr,
const char *buf, size_t count)
{
struct iwl_priv *priv = (struct iwl_priv *)d->driver_data;
unsigned long val;
u32 filter_flags;
int ret = strict_strtoul(buf, 0, &val);
if (ret)
return ret;
filter_flags = (u32)val;
mutex_lock(&priv->mutex);
if (le32_to_cpu(priv->staging_rxon.filter_flags) != filter_flags) {
/* Cancel any currently running scans... */
if (iwl_scan_cancel_timeout(priv, 100))
IWL_WARNING("Could not cancel scan.\n");
else {
IWL_DEBUG_INFO("Committing rxon.filter_flags = "
"0x%04X\n", filter_flags);
priv->staging_rxon.filter_flags =
cpu_to_le32(filter_flags);
iwl_commit_rxon(priv);
}
}
mutex_unlock(&priv->mutex);
return count;
}
static DEVICE_ATTR(filter_flags, S_IWUSR | S_IRUGO, show_filter_flags,
store_filter_flags);
static ssize_t store_retry_rate(struct device *d,
struct device_attribute *attr,
const char *buf, size_t count)
{
struct iwl_priv *priv = dev_get_drvdata(d);
long val;
int ret = strict_strtol(buf, 10, &val);
if (!ret)
return ret;
priv->retry_rate = (val > 0) ? val : 1;
return count;
}
static ssize_t show_retry_rate(struct device *d,
struct device_attribute *attr, char *buf)
{
struct iwl_priv *priv = dev_get_drvdata(d);
return sprintf(buf, "%d", priv->retry_rate);
}
static DEVICE_ATTR(retry_rate, S_IWUSR | S_IRUSR, show_retry_rate,
store_retry_rate);
static ssize_t store_power_level(struct device *d,
struct device_attribute *attr,
const char *buf, size_t count)
{
struct iwl_priv *priv = dev_get_drvdata(d);
int ret;
unsigned long mode;
mutex_lock(&priv->mutex);
if (!iwl_is_ready(priv)) {
ret = -EAGAIN;
goto out;
}
ret = strict_strtoul(buf, 10, &mode);
if (ret)
goto out;
ret = iwl_power_set_user_mode(priv, mode);
if (ret) {
IWL_DEBUG_MAC80211("failed setting power mode.\n");
goto out;
}
ret = count;
out:
mutex_unlock(&priv->mutex);
return ret;
}
static ssize_t show_power_level(struct device *d,
struct device_attribute *attr, char *buf)
{
struct iwl_priv *priv = dev_get_drvdata(d);
int mode = priv->power_data.user_power_setting;
int system = priv->power_data.system_power_setting;
int level = priv->power_data.power_mode;
char *p = buf;
switch (system) {
case IWL_POWER_SYS_AUTO:
p += sprintf(p, "SYSTEM:auto");
break;
case IWL_POWER_SYS_AC:
p += sprintf(p, "SYSTEM:ac");
break;
case IWL_POWER_SYS_BATTERY:
p += sprintf(p, "SYSTEM:battery");
break;
}
p += sprintf(p, "\tMODE:%s", (mode < IWL_POWER_AUTO) ?
"fixed" : "auto");
p += sprintf(p, "\tINDEX:%d", level);
p += sprintf(p, "\n");
return p - buf + 1;
}
static DEVICE_ATTR(power_level, S_IWUSR | S_IRUSR, show_power_level,
store_power_level);
static ssize_t show_channels(struct device *d,
struct device_attribute *attr, char *buf)
{
struct iwl_priv *priv = dev_get_drvdata(d);
struct ieee80211_channel *channels = NULL;
const struct ieee80211_supported_band *supp_band = NULL;
int len = 0, i;
int count = 0;
if (!test_bit(STATUS_GEO_CONFIGURED, &priv->status))
return -EAGAIN;
supp_band = iwl_get_hw_mode(priv, IEEE80211_BAND_2GHZ);
channels = supp_band->channels;
count = supp_band->n_channels;
len += sprintf(&buf[len],
"Displaying %d channels in 2.4GHz band "
"(802.11bg):\n", count);
for (i = 0; i < count; i++)
len += sprintf(&buf[len], "%d: %ddBm: BSS%s%s, %s.\n",
ieee80211_frequency_to_channel(
channels[i].center_freq),
channels[i].max_power,
channels[i].flags & IEEE80211_CHAN_RADAR ?
" (IEEE 802.11h required)" : "",
(!(channels[i].flags & IEEE80211_CHAN_NO_IBSS)
|| (channels[i].flags &
IEEE80211_CHAN_RADAR)) ? "" :
", IBSS",
channels[i].flags &
IEEE80211_CHAN_PASSIVE_SCAN ?
"passive only" : "active/passive");
supp_band = iwl_get_hw_mode(priv, IEEE80211_BAND_5GHZ);
channels = supp_band->channels;
count = supp_band->n_channels;
len += sprintf(&buf[len], "Displaying %d channels in 5.2GHz band "
"(802.11a):\n", count);
for (i = 0; i < count; i++)
len += sprintf(&buf[len], "%d: %ddBm: BSS%s%s, %s.\n",
ieee80211_frequency_to_channel(
channels[i].center_freq),
channels[i].max_power,
channels[i].flags & IEEE80211_CHAN_RADAR ?
" (IEEE 802.11h required)" : "",
((channels[i].flags & IEEE80211_CHAN_NO_IBSS)
|| (channels[i].flags &
IEEE80211_CHAN_RADAR)) ? "" :
", IBSS",
channels[i].flags &
IEEE80211_CHAN_PASSIVE_SCAN ?
"passive only" : "active/passive");
return len;
}
static DEVICE_ATTR(channels, S_IRUSR, show_channels, NULL);
static ssize_t show_statistics(struct device *d,
struct device_attribute *attr, char *buf)
{
struct iwl_priv *priv = dev_get_drvdata(d);
u32 size = sizeof(struct iwl_notif_statistics);
u32 len = 0, ofs = 0;
u8 *data = (u8 *)&priv->statistics;
int rc = 0;
if (!iwl_is_alive(priv))
return -EAGAIN;
mutex_lock(&priv->mutex);
rc = iwl_send_statistics_request(priv, 0);
mutex_unlock(&priv->mutex);
if (rc) {
len = sprintf(buf,
"Error sending statistics request: 0x%08X\n", rc);
return len;
}
while (size && (PAGE_SIZE - len)) {
hex_dump_to_buffer(data + ofs, size, 16, 1, buf + len,
PAGE_SIZE - len, 1);
len = strlen(buf);
if (PAGE_SIZE - len)
buf[len++] = '\n';
ofs += 16;
size -= min(size, 16U);
}
return len;
}
static DEVICE_ATTR(statistics, S_IRUGO, show_statistics, NULL);
static ssize_t show_status(struct device *d,
struct device_attribute *attr, char *buf)
{
struct iwl_priv *priv = (struct iwl_priv *)d->driver_data;
if (!iwl_is_alive(priv))
return -EAGAIN;
return sprintf(buf, "0x%08x\n", (int)priv->status);
}
static DEVICE_ATTR(status, S_IRUGO, show_status, NULL);
/*****************************************************************************
*
* driver setup and teardown
*
*****************************************************************************/
static void iwl_setup_deferred_work(struct iwl_priv *priv)
{
priv->workqueue = create_workqueue(DRV_NAME);
init_waitqueue_head(&priv->wait_command_queue);
INIT_WORK(&priv->up, iwl_bg_up);
INIT_WORK(&priv->restart, iwl_bg_restart);
INIT_WORK(&priv->rx_replenish, iwl_bg_rx_replenish);
INIT_WORK(&priv->rf_kill, iwl_bg_rf_kill);
INIT_WORK(&priv->beacon_update, iwl_bg_beacon_update);
INIT_WORK(&priv->run_time_calib_work, iwl_bg_run_time_calib_work);
INIT_DELAYED_WORK(&priv->init_alive_start, iwl_bg_init_alive_start);
INIT_DELAYED_WORK(&priv->alive_start, iwl_bg_alive_start);
iwl_setup_scan_deferred_work(priv);
iwl_setup_power_deferred_work(priv);
if (priv->cfg->ops->lib->setup_deferred_work)
priv->cfg->ops->lib->setup_deferred_work(priv);
init_timer(&priv->statistics_periodic);
priv->statistics_periodic.data = (unsigned long)priv;
priv->statistics_periodic.function = iwl_bg_statistics_periodic;
tasklet_init(&priv->irq_tasklet, (void (*)(unsigned long))
iwl_irq_tasklet, (unsigned long)priv);
}
static void iwl_cancel_deferred_work(struct iwl_priv *priv)
{
if (priv->cfg->ops->lib->cancel_deferred_work)
priv->cfg->ops->lib->cancel_deferred_work(priv);
cancel_delayed_work_sync(&priv->init_alive_start);
cancel_delayed_work(&priv->scan_check);
cancel_delayed_work_sync(&priv->set_power_save);
cancel_delayed_work(&priv->alive_start);
cancel_work_sync(&priv->beacon_update);
del_timer_sync(&priv->statistics_periodic);
}
static struct attribute *iwl_sysfs_entries[] = {
&dev_attr_channels.attr,
&dev_attr_flags.attr,
&dev_attr_filter_flags.attr,
&dev_attr_power_level.attr,
&dev_attr_retry_rate.attr,
&dev_attr_statistics.attr,
&dev_attr_status.attr,
&dev_attr_temperature.attr,
&dev_attr_tx_power.attr,
#ifdef CONFIG_IWLWIFI_DEBUG
&dev_attr_debug_level.attr,
#endif
&dev_attr_version.attr,
NULL
};
static struct attribute_group iwl_attribute_group = {
.name = NULL, /* put in device directory */
.attrs = iwl_sysfs_entries,
};
static struct ieee80211_ops iwl_hw_ops = {
.tx = iwl_mac_tx,
.start = iwl_mac_start,
.stop = iwl_mac_stop,
.add_interface = iwl_mac_add_interface,
.remove_interface = iwl_mac_remove_interface,
.config = iwl_mac_config,
.config_interface = iwl_mac_config_interface,
.configure_filter = iwl_configure_filter,
.set_key = iwl_mac_set_key,
.update_tkip_key = iwl_mac_update_tkip_key,
.get_stats = iwl_mac_get_stats,
.get_tx_stats = iwl_mac_get_tx_stats,
.conf_tx = iwl_mac_conf_tx,
.reset_tsf = iwl_mac_reset_tsf,
.bss_info_changed = iwl_bss_info_changed,
.ampdu_action = iwl_mac_ampdu_action,
.hw_scan = iwl_mac_hw_scan
};
static int iwl_pci_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
{
int err = 0;
struct iwl_priv *priv;
struct ieee80211_hw *hw;
struct iwl_cfg *cfg = (struct iwl_cfg *)(ent->driver_data);
unsigned long flags;
/************************
* 1. Allocating HW data
************************/
/* Disabling hardware scan means that mac80211 will perform scans
* "the hard way", rather than using device's scan. */
if (cfg->mod_params->disable_hw_scan) {
if (cfg->mod_params->debug & IWL_DL_INFO)
dev_printk(KERN_DEBUG, &(pdev->dev),
"Disabling hw_scan\n");
iwl_hw_ops.hw_scan = NULL;
}
hw = iwl_alloc_all(cfg, &iwl_hw_ops);
if (!hw) {
err = -ENOMEM;
goto out;
}
priv = hw->priv;
/* At this point both hw and priv are allocated. */
SET_IEEE80211_DEV(hw, &pdev->dev);
IWL_DEBUG_INFO("*** LOAD DRIVER ***\n");
priv->cfg = cfg;
priv->pci_dev = pdev;
#ifdef CONFIG_IWLWIFI_DEBUG
priv->debug_level = priv->cfg->mod_params->debug;
atomic_set(&priv->restrict_refcnt, 0);
#endif
/**************************
* 2. Initializing PCI bus
**************************/
if (pci_enable_device(pdev)) {
err = -ENODEV;
goto out_ieee80211_free_hw;
}
pci_set_master(pdev);
err = pci_set_dma_mask(pdev, DMA_BIT_MASK(36));
if (!err)
err = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(36));
if (err) {
err = pci_set_dma_mask(pdev, DMA_BIT_MASK(32));
if (!err)
err = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(32));
/* both attempts failed: */
if (err) {
printk(KERN_WARNING "%s: No suitable DMA available.\n",
DRV_NAME);
goto out_pci_disable_device;
}
}
err = pci_request_regions(pdev, DRV_NAME);
if (err)
goto out_pci_disable_device;
pci_set_drvdata(pdev, priv);
/***********************
* 3. Read REV register
***********************/
priv->hw_base = pci_iomap(pdev, 0, 0);
if (!priv->hw_base) {
err = -ENODEV;
goto out_pci_release_regions;
}
IWL_DEBUG_INFO("pci_resource_len = 0x%08llx\n",
(unsigned long long) pci_resource_len(pdev, 0));
IWL_DEBUG_INFO("pci_resource_base = %p\n", priv->hw_base);
iwl_hw_detect(priv);
printk(KERN_INFO DRV_NAME
": Detected Intel Wireless WiFi Link %s REV=0x%X\n",
priv->cfg->name, priv->hw_rev);
/* We disable the RETRY_TIMEOUT register (0x41) to keep
* PCI Tx retries from interfering with C3 CPU state */
pci_write_config_byte(pdev, PCI_CFG_RETRY_TIMEOUT, 0x00);
/* amp init */
err = priv->cfg->ops->lib->apm_ops.init(priv);
if (err < 0) {
IWL_DEBUG_INFO("Failed to init APMG\n");
goto out_iounmap;
}
/*****************
* 4. Read EEPROM
*****************/
/* Read the EEPROM */
err = iwl_eeprom_init(priv);
if (err) {
IWL_ERROR("Unable to init EEPROM\n");
goto out_iounmap;
}
err = iwl_eeprom_check_version(priv);
if (err)
goto out_iounmap;
/* extract MAC Address */
iwl_eeprom_get_mac(priv, priv->mac_addr);
IWL_DEBUG_INFO("MAC address: %pM\n", priv->mac_addr);
SET_IEEE80211_PERM_ADDR(priv->hw, priv->mac_addr);
/************************
* 5. Setup HW constants
************************/
if (iwl_set_hw_params(priv)) {
IWL_ERROR("failed to set hw parameters\n");
goto out_free_eeprom;
}
/*******************
* 6. Setup priv
*******************/
err = iwl_init_drv(priv);
if (err)
goto out_free_eeprom;
/* At this point both hw and priv are initialized. */
/**********************************
* 7. Initialize module parameters
**********************************/
/* Disable radio (SW RF KILL) via parameter when loading driver */
if (priv->cfg->mod_params->disable) {
set_bit(STATUS_RF_KILL_SW, &priv->status);
IWL_DEBUG_INFO("Radio disabled.\n");
}
/********************
* 8. Setup services
********************/
spin_lock_irqsave(&priv->lock, flags);
iwl_disable_interrupts(priv);
spin_unlock_irqrestore(&priv->lock, flags);
err = sysfs_create_group(&pdev->dev.kobj, &iwl_attribute_group);
if (err) {
IWL_ERROR("failed to create sysfs device attributes\n");
goto out_uninit_drv;
}
iwl_setup_deferred_work(priv);
iwl_setup_rx_handlers(priv);
/********************
* 9. Conclude
********************/
pci_save_state(pdev);
pci_disable_device(pdev);
/**********************************
* 10. Setup and register mac80211
**********************************/
err = iwl_setup_mac(priv);
if (err)
goto out_remove_sysfs;
err = iwl_dbgfs_register(priv, DRV_NAME);
if (err)
IWL_ERROR("failed to create debugfs files\n");
err = iwl_rfkill_init(priv);
if (err)
IWL_ERROR("Unable to initialize RFKILL system. "
"Ignoring error: %d\n", err);
iwl_power_initialize(priv);
return 0;
out_remove_sysfs:
sysfs_remove_group(&pdev->dev.kobj, &iwl_attribute_group);
out_uninit_drv:
iwl_uninit_drv(priv);
out_free_eeprom:
iwl_eeprom_free(priv);
out_iounmap:
pci_iounmap(pdev, priv->hw_base);
out_pci_release_regions:
pci_release_regions(pdev);
pci_set_drvdata(pdev, NULL);
out_pci_disable_device:
pci_disable_device(pdev);
out_ieee80211_free_hw:
ieee80211_free_hw(priv->hw);
out:
return err;
}
static void __devexit iwl_pci_remove(struct pci_dev *pdev)
{
struct iwl_priv *priv = pci_get_drvdata(pdev);
unsigned long flags;
if (!priv)
return;
IWL_DEBUG_INFO("*** UNLOAD DRIVER ***\n");
iwl_dbgfs_unregister(priv);
sysfs_remove_group(&pdev->dev.kobj, &iwl_attribute_group);
/* ieee80211_unregister_hw call wil cause iwl_mac_stop to
* to be called and iwl_down since we are removing the device
* we need to set STATUS_EXIT_PENDING bit.
*/
set_bit(STATUS_EXIT_PENDING, &priv->status);
if (priv->mac80211_registered) {
ieee80211_unregister_hw(priv->hw);
priv->mac80211_registered = 0;
} else {
iwl_down(priv);
}
/* make sure we flush any pending irq or
* tasklet for the driver
*/
spin_lock_irqsave(&priv->lock, flags);
iwl_disable_interrupts(priv);
spin_unlock_irqrestore(&priv->lock, flags);
iwl_synchronize_irq(priv);
iwl_rfkill_unregister(priv);
iwl_dealloc_ucode_pci(priv);
if (priv->rxq.bd)
iwl_rx_queue_free(priv, &priv->rxq);
iwl_hw_txq_ctx_free(priv);
iwl_clear_stations_table(priv);
iwl_eeprom_free(priv);
/*netif_stop_queue(dev); */
flush_workqueue(priv->workqueue);
/* ieee80211_unregister_hw calls iwl_mac_stop, which flushes
* priv->workqueue... so we can't take down the workqueue
* until now... */
destroy_workqueue(priv->workqueue);
priv->workqueue = NULL;
pci_iounmap(pdev, priv->hw_base);
pci_release_regions(pdev);
pci_disable_device(pdev);
pci_set_drvdata(pdev, NULL);
iwl_uninit_drv(priv);
if (priv->ibss_beacon)
dev_kfree_skb(priv->ibss_beacon);
ieee80211_free_hw(priv->hw);
}
#ifdef CONFIG_PM
static int iwl_pci_suspend(struct pci_dev *pdev, pm_message_t state)
{
struct iwl_priv *priv = pci_get_drvdata(pdev);
if (priv->is_open) {
set_bit(STATUS_IN_SUSPEND, &priv->status);
iwl_mac_stop(priv->hw);
priv->is_open = 1;
}
pci_set_power_state(pdev, PCI_D3hot);
return 0;
}
static int iwl_pci_resume(struct pci_dev *pdev)
{
struct iwl_priv *priv = pci_get_drvdata(pdev);
pci_set_power_state(pdev, PCI_D0);
if (priv->is_open)
iwl_mac_start(priv->hw);
clear_bit(STATUS_IN_SUSPEND, &priv->status);
return 0;
}
#endif /* CONFIG_PM */
/*****************************************************************************
*
* driver and module entry point
*
*****************************************************************************/
/* Hardware specific file defines the PCI IDs table for that hardware module */
static struct pci_device_id iwl_hw_card_ids[] = {
#ifdef CONFIG_IWL4965
{IWL_PCI_DEVICE(0x4229, PCI_ANY_ID, iwl4965_agn_cfg)},
{IWL_PCI_DEVICE(0x4230, PCI_ANY_ID, iwl4965_agn_cfg)},
#endif /* CONFIG_IWL4965 */
#ifdef CONFIG_IWL5000
{IWL_PCI_DEVICE(0x4232, 0x1205, iwl5100_bg_cfg)},
{IWL_PCI_DEVICE(0x4232, 0x1305, iwl5100_bg_cfg)},
{IWL_PCI_DEVICE(0x4232, 0x1206, iwl5100_abg_cfg)},
{IWL_PCI_DEVICE(0x4232, 0x1306, iwl5100_abg_cfg)},
{IWL_PCI_DEVICE(0x4232, 0x1326, iwl5100_abg_cfg)},
{IWL_PCI_DEVICE(0x4237, 0x1216, iwl5100_abg_cfg)},
{IWL_PCI_DEVICE(0x4232, PCI_ANY_ID, iwl5100_agn_cfg)},
{IWL_PCI_DEVICE(0x4235, PCI_ANY_ID, iwl5300_agn_cfg)},
{IWL_PCI_DEVICE(0x4236, PCI_ANY_ID, iwl5300_agn_cfg)},
{IWL_PCI_DEVICE(0x4237, PCI_ANY_ID, iwl5100_agn_cfg)},
/* 5350 WiFi/WiMax */
{IWL_PCI_DEVICE(0x423A, 0x1001, iwl5350_agn_cfg)},
{IWL_PCI_DEVICE(0x423A, 0x1021, iwl5350_agn_cfg)},
{IWL_PCI_DEVICE(0x423B, 0x1011, iwl5350_agn_cfg)},
#endif /* CONFIG_IWL5000 */
{0}
};
MODULE_DEVICE_TABLE(pci, iwl_hw_card_ids);
static struct pci_driver iwl_driver = {
.name = DRV_NAME,
.id_table = iwl_hw_card_ids,
.probe = iwl_pci_probe,
.remove = __devexit_p(iwl_pci_remove),
#ifdef CONFIG_PM
.suspend = iwl_pci_suspend,
.resume = iwl_pci_resume,
#endif
};
static int __init iwl_init(void)
{
int ret;
printk(KERN_INFO DRV_NAME ": " DRV_DESCRIPTION ", " DRV_VERSION "\n");
printk(KERN_INFO DRV_NAME ": " DRV_COPYRIGHT "\n");
ret = iwlagn_rate_control_register();
if (ret) {
IWL_ERROR("Unable to register rate control algorithm: %d\n", ret);
return ret;
}
ret = pci_register_driver(&iwl_driver);
if (ret) {
IWL_ERROR("Unable to initialize PCI module\n");
goto error_register;
}
return ret;
error_register:
iwlagn_rate_control_unregister();
return ret;
}
static void __exit iwl_exit(void)
{
pci_unregister_driver(&iwl_driver);
iwlagn_rate_control_unregister();
}
module_exit(iwl_exit);
module_init(iwl_init);