atmel_spi: clean up SPIv1 quirk handling
Currently, we have a flag called "new_1" which is basically equivalent
to cpu_is_at91rm9200(). The latter is also called directly a few places.
Clean up this mess by introducing a atmel_spi_v2() function for
determining the controller version, and move all version dependent code
over to use it. This allows us to remove the new_1 flag.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
diff --git a/drivers/spi/atmel_spi.c b/drivers/spi/atmel_spi.c
index 8abae4a..b4f7f1c 100644
--- a/drivers/spi/atmel_spi.c
+++ b/drivers/spi/atmel_spi.c
@@ -30,13 +30,6 @@
* The core SPI transfer engine just talks to a register bank to set up
* DMA transfers; transfer queue progress is driven by IRQs. The clock
* framework provides the base clock, subdivided for each spi_device.
- *
- * Newer controllers, marked with "new_1" flag, have:
- * - CR.LASTXFER
- * - SPI_MR.DIV32 may become FDIV or must-be-zero (here: always zero)
- * - SPI_SR.TXEMPTY, SPI_SR.NSSR (and corresponding irqs)
- * - SPI_CSRx.CSAAT
- * - SPI_CSRx.SBCR allows faster clocking
*/
struct atmel_spi {
spinlock_t lock;
@@ -45,7 +38,6 @@
int irq;
struct clk *clk;
struct platform_device *pdev;
- unsigned new_1:1;
struct spi_device *stay;
u8 stopping;
@@ -63,6 +55,23 @@
#define INVALID_DMA_ADDRESS 0xffffffff
/*
+ * Version 2 of the SPI controller has
+ * - CR.LASTXFER
+ * - SPI_MR.DIV32 may become FDIV or must-be-zero (here: always zero)
+ * - SPI_SR.TXEMPTY, SPI_SR.NSSR (and corresponding irqs)
+ * - SPI_CSRx.CSAAT
+ * - SPI_CSRx.SBCR allows faster clocking
+ *
+ * We can determine the controller version by reading the VERSION
+ * register, but I haven't checked that it exists on all chips, and
+ * this is cheaper anyway.
+ */
+static bool atmel_spi_is_v2(void)
+{
+ return !cpu_is_at91rm9200();
+}
+
+/*
* Earlier SPI controllers (e.g. on at91rm9200) have a design bug whereby
* they assume that spi slave device state will not change on deselect, so
* that automagic deselection is OK. ("NPCSx rises if no data is to be
@@ -105,7 +114,7 @@
gpio, active ? " (high)" : "",
mr);
- if (!(cpu_is_at91rm9200() && spi->chip_select == 0))
+ if (atmel_spi_is_v2() || spi->chip_select != 0)
gpio_set_value(gpio, active);
spi_writel(as, MR, mr);
}
@@ -129,7 +138,7 @@
gpio, active ? " (low)" : "",
mr);
- if (!(cpu_is_at91rm9200() && spi->chip_select == 0))
+ if (atmel_spi_is_v2() || spi->chip_select != 0)
gpio_set_value(gpio, !active);
}
@@ -536,19 +545,16 @@
}
/* see notes above re chipselect */
- if (cpu_is_at91rm9200()
+ if (!atmel_spi_is_v2()
&& spi->chip_select == 0
&& (spi->mode & SPI_CS_HIGH)) {
dev_dbg(&spi->dev, "setup: can't be active-high\n");
return -EINVAL;
}
- /*
- * Pre-new_1 chips start out at half the peripheral
- * bus speed.
- */
+ /* v1 chips start out at half the peripheral bus speed. */
bus_hz = clk_get_rate(as->clk);
- if (!as->new_1)
+ if (!atmel_spi_is_v2())
bus_hz /= 2;
if (spi->max_speed_hz) {
@@ -755,8 +761,6 @@
goto out_free_buffer;
as->irq = irq;
as->clk = clk;
- if (!cpu_is_at91rm9200())
- as->new_1 = 1;
ret = request_irq(irq, atmel_spi_interrupt, 0,
pdev->dev.bus_id, master);