arm64: Broadcom Vulcan support
Add a configuration option and a device tree for Broadcom's Vulcan
ARM64 processor. vulcan.dtsi has the on-chip blocks like the PCIe
controller, GICv3 with ITS, PMU, system timer and the pl011 UART.
vulcan-eval.dts has definitions for a basic evaluation board.
Vulcan's processor cores support the ARMv8.1 instruction set and
will use "brcm,vulcan" as the compatible property. The firmware
has PSCI 0.2 support for cpu wakeup.
Signed-off-by: Zi Shen Lim <zlim@broadcom.com>
[ updated and split dts - jchandra@broadcom.com ]
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
diff --git a/arch/arm64/boot/dts/broadcom/vulcan.dtsi b/arch/arm64/boot/dts/broadcom/vulcan.dtsi
new file mode 100644
index 0000000..c49b5a8
--- /dev/null
+++ b/arch/arm64/boot/dts/broadcom/vulcan.dtsi
@@ -0,0 +1,144 @@
+/*
+ * dtsi file for Broadcom (BRCM) Vulcan processor
+ *
+ * Copyright (c) 2013-2016 Broadcom
+ * Author: Zi Shen Lim <zlim@broadcom.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+ model = "Broadcom Vulcan";
+ compatible = "brcm,vulcan-soc";
+ interrupt-parent = <&gic>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ /* just 4 cpus now, 128 needed in full config */
+ cpus {
+ #address-cells = <0x2>;
+ #size-cells = <0x0>;
+
+ cpu@0 {
+ device_type = "cpu";
+ compatible = "brcm,vulcan", "arm,armv8";
+ reg = <0x0 0x0>;
+ enable-method = "psci";
+ };
+
+ cpu@1 {
+ device_type = "cpu";
+ compatible = "brcm,vulcan", "arm,armv8";
+ reg = <0x0 0x1>;
+ enable-method = "psci";
+ };
+
+ cpu@2 {
+ device_type = "cpu";
+ compatible = "brcm,vulcan", "arm,armv8";
+ reg = <0x0 0x2>;
+ enable-method = "psci";
+ };
+
+ cpu@3 {
+ device_type = "cpu";
+ compatible = "brcm,vulcan", "arm,armv8";
+ reg = <0x0 0x3>;
+ enable-method = "psci";
+ };
+ };
+
+ psci {
+ compatible = "arm,psci-0.2";
+ method = "smc";
+ };
+
+ gic: interrupt-controller@400080000 {
+ compatible = "arm,gic-v3";
+ #interrupt-cells = <3>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ interrupt-controller;
+ #redistributor-regions = <1>;
+ reg = <0x04 0x00080000 0x0 0x20000>, /* GICD */
+ <0x04 0x01000000 0x0 0x1000000>; /* GICR */
+ interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+
+ gicits: gic-its@40010000 {
+ compatible = "arm,gic-v3-its";
+ msi-controller;
+ reg = <0x04 0x00100000 0x0 0x20000>; /* GIC ITS */
+ };
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_PPI 14 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_PPI 10 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ pmu {
+ compatible = "arm,armv8-pmuv3";
+ interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>; /* PMU overflow */
+ };
+
+ clk125mhz: uart_clk125mhz {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <125000000>;
+ clock-output-names = "clk125mhz";
+ };
+
+ pci {
+ compatible = "pci-host-ecam-generic";
+ device_type = "pci";
+ #interrupt-cells = <1>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ /* ECAM at 0x3000_0000 - 0x4000_0000 */
+ reg = <0x0 0x30000000 0x0 0x10000000>;
+ reg-names = "PCI ECAM";
+
+ /* IO 0x4000_0000 - 0x4001_0000 */
+ ranges = <0x01000000 0 0x40000000 0 0x40000000 0 0x00010000
+ /* MEM 0x4800_0000 - 0x5000_0000 */
+ 0x02000000 0 0x48000000 0 0x48000000 0 0x08000000
+ /* MEM64 pref 0x6_0000_0000 - 0x7_0000_0000 */
+ 0x43000000 6 0x00000000 6 0x00000000 1 0x00000000>;
+ interrupt-map-mask = <0 0 0 7>;
+ interrupt-map =
+ /* addr pin ic icaddr icintr */
+ <0 0 0 1 &gic 0 0 GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH
+ 0 0 0 2 &gic 0 0 GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH
+ 0 0 0 3 &gic 0 0 GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH
+ 0 0 0 4 &gic 0 0 GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+ msi-parent = <&gicits>;
+ dma-coherent;
+ };
+
+ soc {
+ compatible = "simple-bus";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ uart0: serial@402020000 {
+ compatible = "arm,pl011", "arm,primecell";
+ reg = <0x04 0x02020000 0x0 0x1000>;
+ interrupt-parent = <&gic>;
+ interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk125mhz>;
+ clock-names = "apb_pclk";
+ };
+ };
+
+};