[PATCH] skge: better flow control negotiation
Do flow control negotiation properly. Don't let auto negotiation
status limit renegotiation. Separate desired pause values from
the result of auto negotiation.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
diff --git a/drivers/net/skge.c b/drivers/net/skge.c
index c19f49b..d844a83 100644
--- a/drivers/net/skge.c
+++ b/drivers/net/skge.c
@@ -487,31 +487,37 @@
{
struct skge_port *skge = netdev_priv(dev);
- ecmd->tx_pause = (skge->flow_control == FLOW_MODE_LOC_SEND)
- || (skge->flow_control == FLOW_MODE_SYMMETRIC);
- ecmd->rx_pause = (skge->flow_control == FLOW_MODE_REM_SEND)
- || (skge->flow_control == FLOW_MODE_SYMMETRIC);
+ ecmd->rx_pause = (skge->flow_control == FLOW_MODE_SYMMETRIC)
+ || (skge->flow_control == FLOW_MODE_SYM_OR_REM);
+ ecmd->tx_pause = ecmd->rx_pause || (skge->flow_control == FLOW_MODE_LOC_SEND);
- ecmd->autoneg = skge->autoneg;
+ ecmd->autoneg = ecmd->rx_pause || ecmd->tx_pause;
}
static int skge_set_pauseparam(struct net_device *dev,
struct ethtool_pauseparam *ecmd)
{
struct skge_port *skge = netdev_priv(dev);
+ struct ethtool_pauseparam old;
- skge->autoneg = ecmd->autoneg;
- if (ecmd->rx_pause && ecmd->tx_pause)
- skge->flow_control = FLOW_MODE_SYMMETRIC;
- else if (ecmd->rx_pause && !ecmd->tx_pause)
- skge->flow_control = FLOW_MODE_REM_SEND;
- else if (!ecmd->rx_pause && ecmd->tx_pause)
- skge->flow_control = FLOW_MODE_LOC_SEND;
- else
- skge->flow_control = FLOW_MODE_NONE;
+ skge_get_pauseparam(dev, &old);
+
+ if (ecmd->autoneg != old.autoneg)
+ skge->flow_control = ecmd->autoneg ? FLOW_MODE_NONE : FLOW_MODE_SYMMETRIC;
+ else {
+ if (ecmd->rx_pause && ecmd->tx_pause)
+ skge->flow_control = FLOW_MODE_SYMMETRIC;
+ else if (ecmd->rx_pause && !ecmd->tx_pause)
+ skge->flow_control = FLOW_MODE_SYM_OR_REM;
+ else if (!ecmd->rx_pause && ecmd->tx_pause)
+ skge->flow_control = FLOW_MODE_LOC_SEND;
+ else
+ skge->flow_control = FLOW_MODE_NONE;
+ }
if (netif_running(dev))
skge_phy_reset(skge);
+
return 0;
}
@@ -854,6 +860,23 @@
return 0;
}
+static const char *skge_pause(enum pause_status status)
+{
+ switch(status) {
+ case FLOW_STAT_NONE:
+ return "none";
+ case FLOW_STAT_REM_SEND:
+ return "rx only";
+ case FLOW_STAT_LOC_SEND:
+ return "tx_only";
+ case FLOW_STAT_SYMMETRIC: /* Both station may send PAUSE */
+ return "both";
+ default:
+ return "indeterminated";
+ }
+}
+
+
static void skge_link_up(struct skge_port *skge)
{
skge_write8(skge->hw, SK_REG(skge->port, LNK_LED_REG),
@@ -862,16 +885,13 @@
netif_carrier_on(skge->netdev);
netif_wake_queue(skge->netdev);
- if (netif_msg_link(skge))
+ if (netif_msg_link(skge)) {
printk(KERN_INFO PFX
"%s: Link is up at %d Mbps, %s duplex, flow control %s\n",
skge->netdev->name, skge->speed,
skge->duplex == DUPLEX_FULL ? "full" : "half",
- (skge->flow_control == FLOW_MODE_NONE) ? "none" :
- (skge->flow_control == FLOW_MODE_LOC_SEND) ? "tx only" :
- (skge->flow_control == FLOW_MODE_REM_SEND) ? "rx only" :
- (skge->flow_control == FLOW_MODE_SYMMETRIC) ? "tx and rx" :
- "unknown");
+ skge_pause(skge->flow_status));
+ }
}
static void skge_link_down(struct skge_port *skge)
@@ -1015,7 +1035,7 @@
[FLOW_MODE_NONE] = 0,
[FLOW_MODE_LOC_SEND] = PHY_AN_PAUSE_ASYM,
[FLOW_MODE_SYMMETRIC] = PHY_AN_PAUSE_CAP,
- [FLOW_MODE_REM_SEND] = PHY_AN_PAUSE_CAP | PHY_AN_PAUSE_ASYM,
+ [FLOW_MODE_SYM_OR_REM] = PHY_AN_PAUSE_CAP | PHY_AN_PAUSE_ASYM,
};
/* special defines for FIBER (88E1011S only) */
@@ -1023,7 +1043,7 @@
[FLOW_MODE_NONE] = PHY_X_P_NO_PAUSE,
[FLOW_MODE_LOC_SEND] = PHY_X_P_ASYM_MD,
[FLOW_MODE_SYMMETRIC] = PHY_X_P_SYM_MD,
- [FLOW_MODE_REM_SEND] = PHY_X_P_BOTH_MD,
+ [FLOW_MODE_SYM_OR_REM] = PHY_X_P_BOTH_MD,
};
@@ -1072,20 +1092,19 @@
return;
}
-
/* We are using IEEE 802.3z/D5.0 Table 37-4 */
switch (aux & PHY_B_AS_PAUSE_MSK) {
case PHY_B_AS_PAUSE_MSK:
- skge->flow_control = FLOW_MODE_SYMMETRIC;
+ skge->flow_status = FLOW_STAT_SYMMETRIC;
break;
case PHY_B_AS_PRR:
- skge->flow_control = FLOW_MODE_REM_SEND;
+ skge->flow_status = FLOW_STAT_REM_SEND;
break;
case PHY_B_AS_PRT:
- skge->flow_control = FLOW_MODE_LOC_SEND;
+ skge->flow_status = FLOW_STAT_LOC_SEND;
break;
default:
- skge->flow_control = FLOW_MODE_NONE;
+ skge->flow_status = FLOW_STAT_NONE;
}
skge->speed = SPEED_1000;
}
@@ -1283,15 +1302,20 @@
}
/* We are using IEEE 802.3z/D5.0 Table 37-4 */
- if (lpa & PHY_X_P_SYM_MD)
- skge->flow_control = FLOW_MODE_SYMMETRIC;
- else if ((lpa & PHY_X_RS_PAUSE) == PHY_X_P_ASYM_MD)
- skge->flow_control = FLOW_MODE_REM_SEND;
- else if ((lpa & PHY_X_RS_PAUSE) == PHY_X_P_BOTH_MD)
- skge->flow_control = FLOW_MODE_LOC_SEND;
+ if ((skge->flow_control == FLOW_MODE_SYMMETRIC ||
+ skge->flow_control == FLOW_MODE_SYM_OR_REM) &&
+ (lpa & PHY_X_P_SYM_MD))
+ skge->flow_status = FLOW_STAT_SYMMETRIC;
+ else if (skge->flow_control == FLOW_MODE_SYM_OR_REM &&
+ (lpa & PHY_X_RS_PAUSE) == PHY_X_P_ASYM_MD)
+ /* Enable PAUSE receive, disable PAUSE transmit */
+ skge->flow_status = FLOW_STAT_REM_SEND;
+ else if (skge->flow_control == FLOW_MODE_LOC_SEND &&
+ (lpa & PHY_X_RS_PAUSE) == PHY_X_P_BOTH_MD)
+ /* Disable PAUSE receive, enable PAUSE transmit */
+ skge->flow_status = FLOW_STAT_LOC_SEND;
else
- skge->flow_control = FLOW_MODE_NONE;
-
+ skge->flow_status = FLOW_STAT_NONE;
skge->speed = SPEED_1000;
}
@@ -1602,8 +1626,8 @@
* enabling pause frame reception is required for 1000BT
* because the XMAC is not reset if the link is going down
*/
- if (skge->flow_control == FLOW_MODE_NONE ||
- skge->flow_control == FLOW_MODE_LOC_SEND)
+ if (skge->flow_status == FLOW_STAT_NONE ||
+ skge->flow_status == FLOW_STAT_LOC_SEND)
/* Disable Pause Frame Reception */
cmd |= XM_MMU_IGN_PF;
else
@@ -1613,8 +1637,8 @@
xm_write16(hw, port, XM_MMU_CMD, cmd);
mode = xm_read32(hw, port, XM_MODE);
- if (skge->flow_control == FLOW_MODE_SYMMETRIC ||
- skge->flow_control == FLOW_MODE_LOC_SEND) {
+ if (skge->flow_status== FLOW_STAT_SYMMETRIC ||
+ skge->flow_status == FLOW_STAT_LOC_SEND) {
/*
* Configure Pause Frame Generation
* Use internal and external Pause Frame Generation.
@@ -1938,6 +1962,11 @@
case FLOW_MODE_LOC_SEND:
/* disable Rx flow-control */
reg |= GM_GPCR_FC_RX_DIS | GM_GPCR_AU_FCT_DIS;
+ break;
+ case FLOW_MODE_SYMMETRIC:
+ case FLOW_MODE_SYM_OR_REM:
+ /* enable Tx & Rx flow-control */
+ break;
}
gma_write16(hw, port, GM_GP_CTRL, reg);
@@ -2132,13 +2161,11 @@
ctrl &= ~(GM_GPCR_RX_ENA | GM_GPCR_TX_ENA);
gma_write16(hw, port, GM_GP_CTRL, ctrl);
- if (skge->flow_control == FLOW_MODE_REM_SEND) {
+ if (skge->flow_status == FLOW_STAT_REM_SEND) {
+ ctrl = gm_phy_read(hw, port, PHY_MARV_AUNE_ADV);
+ ctrl |= PHY_M_AN_ASP;
/* restore Asymmetric Pause bit */
- gm_phy_write(hw, port, PHY_MARV_AUNE_ADV,
- gm_phy_read(hw, port,
- PHY_MARV_AUNE_ADV)
- | PHY_M_AN_ASP);
-
+ gm_phy_write(hw, port, PHY_MARV_AUNE_ADV, ctrl);
}
yukon_reset(hw, port);
@@ -2185,19 +2212,19 @@
/* We are using IEEE 802.3z/D5.0 Table 37-4 */
switch (phystat & PHY_M_PS_PAUSE_MSK) {
case PHY_M_PS_PAUSE_MSK:
- skge->flow_control = FLOW_MODE_SYMMETRIC;
+ skge->flow_status = FLOW_STAT_SYMMETRIC;
break;
case PHY_M_PS_RX_P_EN:
- skge->flow_control = FLOW_MODE_REM_SEND;
+ skge->flow_status = FLOW_STAT_REM_SEND;
break;
case PHY_M_PS_TX_P_EN:
- skge->flow_control = FLOW_MODE_LOC_SEND;
+ skge->flow_status = FLOW_STAT_LOC_SEND;
break;
default:
- skge->flow_control = FLOW_MODE_NONE;
+ skge->flow_status = FLOW_STAT_NONE;
}
- if (skge->flow_control == FLOW_MODE_NONE ||
+ if (skge->flow_status == FLOW_STAT_NONE ||
(skge->speed < SPEED_1000 && skge->duplex == DUPLEX_HALF))
skge_write8(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_OFF);
else
@@ -3420,7 +3447,7 @@
/* Auto speed and flow control */
skge->autoneg = AUTONEG_ENABLE;
- skge->flow_control = FLOW_MODE_SYMMETRIC;
+ skge->flow_control = FLOW_MODE_SYM_OR_REM;
skge->duplex = -1;
skge->speed = -1;
skge->advertising = skge_supported_modes(hw);
diff --git a/drivers/net/skge.h b/drivers/net/skge.h
index 9cc955c..537c0aa 100644
--- a/drivers/net/skge.h
+++ b/drivers/net/skge.h
@@ -2427,13 +2427,24 @@
struct mutex phy_mutex;
};
-enum {
- FLOW_MODE_NONE = 0, /* No Flow-Control */
- FLOW_MODE_LOC_SEND = 1, /* Local station sends PAUSE */
- FLOW_MODE_REM_SEND = 2, /* Symmetric or just remote */
+enum pause_control {
+ FLOW_MODE_NONE = 1, /* No Flow-Control */
+ FLOW_MODE_LOC_SEND = 2, /* Local station sends PAUSE */
FLOW_MODE_SYMMETRIC = 3, /* Both stations may send PAUSE */
+ FLOW_MODE_SYM_OR_REM = 4, /* Both stations may send PAUSE or
+ * just the remote station may send PAUSE
+ */
};
+enum pause_status {
+ FLOW_STAT_INDETERMINATED=0, /* indeterminated */
+ FLOW_STAT_NONE, /* No Flow Control */
+ FLOW_STAT_REM_SEND, /* Remote Station sends PAUSE */
+ FLOW_STAT_LOC_SEND, /* Local station sends PAUSE */
+ FLOW_STAT_SYMMETRIC, /* Both station may send PAUSE */
+};
+
+
struct skge_port {
u32 msg_enable;
struct skge_hw *hw;
@@ -2446,9 +2457,10 @@
struct net_device_stats net_stats;
struct work_struct link_thread;
+ enum pause_control flow_control;
+ enum pause_status flow_status;
u8 rx_csum;
u8 blink_on;
- u8 flow_control;
u8 wol;
u8 autoneg; /* AUTONEG_ENABLE, AUTONEG_DISABLE */
u8 duplex; /* DUPLEX_HALF, DUPLEX_FULL */