Merge tag 'omap-for-v3.13/dt-late' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Some more dts changes from Benoit Cousson <bcousson@baylibre.com> via
Tony Lindgren:
- Add a lot of N900 nodes
- Add OPP table to OMAP5/DRA7
- Add support for Newflow NanoBone board
- Add i2c aliases
- Add McASP and audio support
- Add reset/idle on init bindings for OMAP
- Add more nodes for AM4272
* tag 'omap-for-v3.13/dt-late' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (42 commits)
ARM: dts: omap5-uevm: Remove pinmux for dmic pins
ARM: dts: omap5-uevm: Correct twl6040 reset GPIO pinmux
ARM: dts: TWL4030: Add power button support
ARM: dts: omap3-n900: Add LP5523 support
ARM: dts: omap3-n900: Add TLV320AIC3X support
ARM: dts: omap3-n900:: Mux RX51_LCD_RESET_GPIO in DTS
ARM: dts: omap3-n900: Add NAND support
ARM: dts: omap3-n900: Specify regulator info
ARM: dts: TWL4030: Add missing regulators
ARM: dts: omap3-n900: Add LP5523 support
ARM: dts: omap3-n900: Add vibrator device
ARM: dts: omap3-n900: GPIO key definitions
ARM: dts: omap3-n900: Add support for SD cards
ARM: dts: omap3-n900: Add UART support
ARM: dts: omap3-n900: Fix i2c bus speed
ARM: dts: omap3-n900: Add pinctrl for i2c devices
ARM: dts: DRA7: Add CPU OPP table
ARM: dts: OMAP5: Add CPU OPP table
ARM: dts: dra7-evm: add smps123 supply for CPU
ARM: dts: omap5-uevm: add smps123 supply for CPU
...
Signed-off-by: Olof Johansson <olof@lixom.net>
diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt
index 91b7049..808c154 100644
--- a/Documentation/devicetree/bindings/arm/omap/omap.txt
+++ b/Documentation/devicetree/bindings/arm/omap/omap.txt
@@ -21,7 +21,8 @@
Optional properties:
- ti,no_idle_on_suspend: When present, it prevents the PM to idle the module
during suspend.
-
+- ti,no-reset-on-init: When present, the module should not be reset at init
+- ti,no-idle-on-init: When present, the module should not be idled at init
Example:
diff --git a/MAINTAINERS b/MAINTAINERS
index 1f006f1..cb1f2e0 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -6088,6 +6088,12 @@
S: Maintained
F: drivers/gpio/gpio-omap.c
+OMAP/NEWFLOW NANOBONE MACHINE SUPPORT
+M: Mark Jackson <mpfj@newflow.co.uk>
+L: linux-omap@vger.kernel.org
+S: Maintained
+F: arch/arm/boot/dts/am335x-nano.dts
+
OMFS FILESYSTEM
M: Bob Copeland <me@bobcopeland.com>
L: linux-karma-devel@lists.sourceforge.net
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index f2ff626..b590bce 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -197,6 +197,7 @@
am335x-evmsk.dtb \
am335x-bone.dtb \
am335x-boneblack.dtb \
+ am335x-nano.dtb \
am335x-base0033.dtb \
am3517-evm.dtb \
am3517_mt_ventoux.dtb \
diff --git a/arch/arm/boot/dts/am335x-evm.dts b/arch/arm/boot/dts/am335x-evm.dts
index eabacf9..9874294 100644
--- a/arch/arm/boot/dts/am335x-evm.dts
+++ b/arch/arm/boot/dts/am335x-evm.dts
@@ -119,6 +119,19 @@
};
};
};
+
+ sound {
+ compatible = "ti,da830-evm-audio";
+ ti,model = "AM335x-EVM";
+ ti,audio-codec = <&tlv320aic3106>;
+ ti,mcasp-controller = <&mcasp1>;
+ ti,codec-clock-rate = <12000000>;
+ ti,audio-routing =
+ "Headphone Jack", "HPLOUT",
+ "Headphone Jack", "HPROUT",
+ "LINE1L", "Line In",
+ "LINE1R", "Line In";
+ };
};
&am33xx_pinmux {
@@ -279,6 +292,15 @@
0xec 0x00 /* lcd_ac_bias_en.lcd_ac_bias_en, OUTPUT | MODE0 */
>;
};
+
+ am335x_evm_audio_pins: am335x_evm_audio_pins {
+ pinctrl-single,pins = <
+ 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE4) /* mii1_rx_dv.mcasp1_aclkx */
+ 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* mii1_txd3.mcasp1_fsx */
+ 0x108 (PIN_OUTPUT_PULLDOWN | MUX_MODE4) /* mii1_col.mcasp1_axr2 */
+ 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* rmii1_ref_clk.mcasp1_axr3 */
+ >;
+ };
};
&uart0 {
@@ -373,6 +395,18 @@
compatible = "ti,tmp275";
reg = <0x48>;
};
+
+ tlv320aic3106: tlv320aic3106@1b {
+ compatible = "ti,tlv320aic3106";
+ reg = <0x1b>;
+ status = "okay";
+
+ /* Regulators */
+ AVDD-supply = <&vaux2_reg>;
+ IOVDD-supply = <&vaux2_reg>;
+ DRVDD-supply = <&vaux2_reg>;
+ DVDD-supply = <&vbat>;
+ };
};
&lcdc {
@@ -476,6 +510,22 @@
#include "tps65910.dtsi"
+&mcasp1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&am335x_evm_audio_pins>;
+
+ status = "okay";
+
+ op-mode = <0>; /* MCASP_IIS_MODE */
+ tdm-slots = <2>;
+ /* 4 serializers */
+ serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX */
+ 0 0 1 2
+ >;
+ tx-num-evt = <1>;
+ rx-num-evt = <1>;
+};
+
&tps {
vcc1-supply = <&vbat>;
vcc2-supply = <&vbat>;
diff --git a/arch/arm/boot/dts/am335x-evmsk.dts b/arch/arm/boot/dts/am335x-evmsk.dts
index 5f12b28..03febf8 100644
--- a/arch/arm/boot/dts/am335x-evmsk.dts
+++ b/arch/arm/boot/dts/am335x-evmsk.dts
@@ -115,6 +115,17 @@
brightness-levels = <0 58 61 66 75 90 125 170 255>;
default-brightness-level = <8>;
};
+
+ sound {
+ compatible = "ti,da830-evm-audio";
+ ti,model = "AM335x-EVMSK";
+ ti,audio-codec = <&tlv320aic3106>;
+ ti,mcasp-controller = <&mcasp1>;
+ ti,codec-clock-rate = <24576000>;
+ ti,audio-routing =
+ "Headphone Jack", "HPLOUT",
+ "Headphone Jack", "HPROUT";
+ };
};
&am33xx_pinmux {
@@ -244,6 +255,15 @@
0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
>;
};
+
+ mcasp1_pins: mcasp1_pins {
+ pinctrl-single,pins = <
+ 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE4) /* mii1_crs.mcasp1_aclkx */
+ 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* mii1_rxerr.mcasp1_fsx */
+ 0x108 (PIN_OUTPUT_PULLDOWN | MUX_MODE4) /* mii1_col.mcasp1_axr2 */
+ 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* rmii1_ref_clk.mcasp1_axr3 */
+ >;
+ };
};
&uart0 {
@@ -291,6 +311,18 @@
st,max-limit-y = <550>;
st,max-limit-z = <750>;
};
+
+ tlv320aic3106: tlv320aic3106@1b {
+ compatible = "ti,tlv320aic3106";
+ reg = <0x1b>;
+ status = "okay";
+
+ /* Regulators */
+ AVDD-supply = <&vaux2_reg>;
+ IOVDD-supply = <&vaux2_reg>;
+ DRVDD-supply = <&vaux2_reg>;
+ DVDD-supply = <&vbat>;
+ };
};
&usb {
@@ -433,3 +465,23 @@
&aes {
status = "okay";
};
+
+&gpio0 {
+ ti,no-reset-on-init;
+};
+
+&mcasp1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcasp1_pins>;
+
+ status = "okay";
+
+ op-mode = <0>; /* MCASP_IIS_MODE */
+ tdm-slots = <2>;
+ /* 4 serializers */
+ serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX */
+ 0 0 1 2
+ >;
+ tx-num-evt = <1>;
+ rx-num-evt = <1>;
+};
diff --git a/arch/arm/boot/dts/am335x-igep0033.dtsi b/arch/arm/boot/dts/am335x-igep0033.dtsi
index 06eba07..6196244 100644
--- a/arch/arm/boot/dts/am335x-igep0033.dtsi
+++ b/arch/arm/boot/dts/am335x-igep0033.dtsi
@@ -44,6 +44,13 @@
regulator-max-microvolt = <5000000>;
regulator-boot-on;
};
+
+ vmmc: fixedregulator@0 {
+ compatible = "regulator-fixed";
+ regulator-name = "vmmc";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
};
&am33xx_pinmux {
@@ -180,6 +187,12 @@
};
};
+&mmc1 {
+ status = "okay";
+ vmmc-supply = <&vmmc>;
+ bus-width = <4>;
+};
+
&uart0 {
status = "okay";
pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/am335x-nano.dts b/arch/arm/boot/dts/am335x-nano.dts
new file mode 100644
index 0000000..9907b49
--- /dev/null
+++ b/arch/arm/boot/dts/am335x-nano.dts
@@ -0,0 +1,431 @@
+/*
+ * Copyright (C) 2013 Newflow Ltd - http://www.newflow.co.uk/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+#include "am33xx.dtsi"
+
+/ {
+ model = "Newflow AM335x NanoBone";
+ compatible = "ti,am33xx";
+
+ cpus {
+ cpu@0 {
+ cpu0-supply = <&dcdc2_reg>;
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x80000000 0x10000000>; /* 256 MB */
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led@0 {
+ label = "nanobone:green:usr1";
+ gpios = <&gpio1 5 0>;
+ default-state = "off";
+ };
+ };
+};
+
+&am33xx_pinmux {
+ pinctrl-names = "default";
+ pinctrl-0 = <&misc_pins>;
+
+ misc_pins: misc_pins {
+ pinctrl-single,pins = <
+ 0x15c (PIN_OUTPUT | MUX_MODE7) /* spi0_cs0.gpio0_5 */
+ >;
+ };
+
+ gpmc_pins: gpmc_pins {
+ pinctrl-single,pins = <
+ 0x0 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad0.gpmc_ad0 */
+ 0x4 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad1.gpmc_ad1 */
+ 0x8 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad2.gpmc_ad2 */
+ 0xc (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad3.gpmc_ad3 */
+ 0x10 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad4.gpmc_ad4 */
+ 0x14 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad5.gpmc_ad5 */
+ 0x18 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad6.gpmc_ad6 */
+ 0x1c (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad7.gpmc_ad7 */
+ 0x20 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad8.gpmc_ad8 */
+ 0x24 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad9.gpmc_ad9 */
+ 0x28 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad10.gpmc_ad10 */
+ 0x2c (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad11.gpmc_ad11 */
+ 0x30 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad12.gpmc_ad12 */
+ 0x34 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad13.gpmc_ad13 */
+ 0x38 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad14.gpmc_ad14 */
+ 0x3c (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad15.gpmc_ad15 */
+
+ 0x70 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_wait0.gpmc_wait0 */
+ 0x7c (PIN_OUTPUT | MUX_MODE0) /* gpmc_csn0.gpmc_csn0 */
+ 0x80 (PIN_OUTPUT | MUX_MODE0) /* gpmc_csn1.gpmc_csn1 */
+ 0x84 (PIN_OUTPUT | MUX_MODE0) /* gpmc_csn2.gpmc_csn2 */
+ 0x88 (PIN_OUTPUT | MUX_MODE0) /* gpmc_csn3.gpmc_csn3 */
+
+ 0x90 (PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale.gpmc_advn_ale */
+ 0x94 (PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren.gpmc_oen_ren */
+ 0x98 (PIN_OUTPUT | MUX_MODE0) /* gpmc_wen.gpmc_wen */
+ 0x9c (PIN_OUTPUT | MUX_MODE0) /* gpmc_ben0_cle.gpmc_ben0_cle */
+
+ 0xa4 (PIN_OUTPUT | MUX_MODE1) /* lcd_data1.gpmc_a1 */
+ 0xa8 (PIN_OUTPUT | MUX_MODE1) /* lcd_data2.gpmc_a2 */
+ 0xac (PIN_OUTPUT | MUX_MODE1) /* lcd_data3.gpmc_a3 */
+ 0xb0 (PIN_OUTPUT | MUX_MODE1) /* lcd_data4.gpmc_a4 */
+ 0xb4 (PIN_OUTPUT | MUX_MODE1) /* lcd_data5.gpmc_a5 */
+ 0xb8 (PIN_OUTPUT | MUX_MODE1) /* lcd_data6.gpmc_a6 */
+ 0xbc (PIN_OUTPUT | MUX_MODE1) /* lcd_data7.gpmc_a7 */
+
+ 0xe0 (PIN_OUTPUT | MUX_MODE1) /* lcd_vsync.gpmc_a8 */
+ 0xe4 (PIN_OUTPUT | MUX_MODE1) /* lcd_hsync.gpmc_a9 */
+ 0xe8 (PIN_OUTPUT | MUX_MODE1) /* lcd_pclk.gpmc_a10 */
+ >;
+ };
+
+ i2c0_pins: i2c0_pins {
+ pinctrl-single,pins = <
+ 0x188 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* i2c0_sda.i2c0_sda */
+ 0x18c (PIN_INPUT_PULLDOWN | MUX_MODE0) /* i2c0_scl.i2c0_scl */
+ >;
+ };
+
+ uart0_pins: uart0_pins {
+ pinctrl-single,pins = <
+ 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */
+ 0x174 (PIN_OUTPUT | MUX_MODE0) /* uart0_txd.uart0_txd */
+ >;
+ };
+
+ uart1_pins: uart1_pins {
+ pinctrl-single,pins = <
+ 0x178 (PIN_OUTPUT | MUX_MODE7) /* uart1_ctsn.uart1_ctsn */
+ 0x17c (PIN_OUTPUT | MUX_MODE7) /* uart1_rtsn.uart1_rtsn */
+ 0x180 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_rxd.uart1_rxd */
+ 0x184 (PIN_OUTPUT | MUX_MODE0) /* uart1_txd.uart1_txd */
+ >;
+ };
+
+ uart2_pins: uart2_pins {
+ pinctrl-single,pins = <
+ 0xc0 (PIN_INPUT_PULLUP | MUX_MODE7) /* lcd_data8.gpio2[14] */
+ 0xc4 (PIN_OUTPUT | MUX_MODE7) /* lcd_data9.gpio2[15] */
+ 0x150 (PIN_INPUT | MUX_MODE1) /* spi0_sclk.uart2_rxd */
+ 0x154 (PIN_OUTPUT | MUX_MODE1) /* spi0_d0.uart2_txd */
+ >;
+ };
+
+ uart3_pins: uart3_pins {
+ pinctrl-single,pins = <
+ 0xc8 (PIN_INPUT_PULLUP | MUX_MODE6) /* lcd_data10.uart3_ctsn */
+ 0xcc (PIN_OUTPUT | MUX_MODE6) /* lcd_data11.uart3_rtsn */
+ 0x160 (PIN_INPUT | MUX_MODE1) /* spi0_cs1.uart3_rxd */
+ 0x164 (PIN_OUTPUT | MUX_MODE1) /* ecap0_in_pwm0_out.uart3_txd */
+ >;
+ };
+
+ uart4_pins: uart4_pins {
+ pinctrl-single,pins = <
+ 0xd0 (PIN_INPUT_PULLUP | MUX_MODE6) /* lcd_data12.uart4_ctsn */
+ 0xd4 (PIN_OUTPUT | MUX_MODE6) /* lcd_data13.uart4_rtsn */
+ 0x168 (PIN_INPUT | MUX_MODE1) /* uart0_ctsn.uart4_rxd */
+ 0x16c (PIN_OUTPUT | MUX_MODE1) /* uart0_rtsn.uart4_txd */
+ >;
+ };
+
+ uart5_pins: uart5_pins {
+ pinctrl-single,pins = <
+ 0xd8 (PIN_INPUT | MUX_MODE4) /* lcd_data14.uart5_rxd */
+ 0x144 (PIN_OUTPUT | MUX_MODE3) /* rmiii1_refclk.uart5_txd */
+ >;
+ };
+
+ mmc1_pins: mmc1_pins {
+ pinctrl-single,pins = <
+ 0xf0 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat0.mmc0_dat0 */
+ 0xf4 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat1.mmc0_dat1 */
+ 0xf8 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat2.mmc0_dat2 */
+ 0xfc (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat3.mmc0_dat3 */
+ 0x100 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_clk.mmc0_clk */
+ 0x104 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_cmd.mmc0_cmd */
+ 0x1e8 (PIN_INPUT_PULLUP | MUX_MODE7) /* emu1.gpio3[8] */
+ 0x1a0 (PIN_INPUT_PULLUP | MUX_MODE7) /* mcasp0_aclkr.gpio3[18] */
+ >;
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+ status = "okay";
+ rts-gpio = <&gpio0 13 GPIO_ACTIVE_HIGH>;
+ rs485-rts-active-high;
+ rs485-rx-during-tx;
+ rs485-rts-delay = <1 1>;
+ linux,rs485-enabled-at-boot-time;
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+ status = "okay";
+ rts-gpio = <&gpio2 15 GPIO_ACTIVE_HIGH>;
+ rs485-rts-active-high;
+ rs485-rts-delay = <1 1>;
+ linux,rs485-enabled-at-boot-time;
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pins>;
+ status = "okay";
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart4_pins>;
+ status = "okay";
+};
+
+&uart5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart5_pins>;
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+ pinctrl-names = "default";
+ clock-frequency = <400000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins>;
+
+ gpio@20 {
+ compatible = "mcp,mcp23017";
+ reg = <0x20>;
+ };
+
+ tps: tps@24 {
+ reg = <0x24>;
+ };
+
+ eeprom@53 {
+ compatible = "mcp,24c02";
+ reg = <0x53>;
+ pagesize = <8>;
+ };
+
+ rtc@68 {
+ compatible = "dallas,ds1307";
+ reg = <0x68>;
+ };
+};
+
+&elm {
+ status = "okay";
+};
+
+&gpmc {
+ compatible = "ti,am3352-gpmc";
+ ti,hwmods = "gpmc";
+ status = "okay";
+ gpmc,num-waitpins = <2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpmc_pins>;
+
+ #address-cells = <2>;
+ #size-cells = <1>;
+ ranges = <0 0 0x08000000 0x08000000>; /* CS0: NOR 128M */
+
+ nor@0,0 {
+ reg = <0 0x00000000 0x08000000>;
+ compatible = "cfi-flash";
+ linux,mtd-name = "spansion,s29gl010p11t";
+ bank-width = <2>;
+
+ gpmc,mux-add-data = <2>;
+
+ gpmc,sync-clk-ps = <0>;
+ gpmc,cs-on-ns = <0>;
+ gpmc,cs-rd-off-ns = <160>;
+ gpmc,cs-wr-off-ns = <160>;
+ gpmc,adv-on-ns = <10>;
+ gpmc,adv-rd-off-ns = <30>;
+ gpmc,adv-wr-off-ns = <30>;
+ gpmc,oe-on-ns = <40>;
+ gpmc,oe-off-ns = <160>;
+ gpmc,we-on-ns = <40>;
+ gpmc,we-off-ns = <160>;
+ gpmc,rd-cycle-ns = <160>;
+ gpmc,wr-cycle-ns = <160>;
+ gpmc,access-ns = <150>;
+ gpmc,page-burst-access-ns = <10>;
+ gpmc,cycle2cycle-samecsen;
+ gpmc,cycle2cycle-delay-ns = <20>;
+ gpmc,wr-data-mux-bus-ns = <70>;
+ gpmc,wr-access-ns = <80>;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ /*
+ MTD partition table
+ ===================
+ +------------+-->0x00000000-> U-Boot start
+ | |
+ | |-->0x000BFFFF-> U-Boot end
+ | |-->0x000C0000-> ENV1 start
+ | |
+ | |-->0x000DFFFF-> ENV1 end
+ | |-->0x000E0000-> ENV2 start
+ | |
+ | |-->0x000FFFFF-> ENV2 end
+ | |-->0x00100000-> Kernel start
+ | |
+ | |-->0x004FFFFF-> Kernel end
+ | |-->0x00500000-> File system start
+ | |
+ | |-->0x014FFFFF-> File system end
+ | |-->0x01500000-> User data start
+ | |
+ | |-->0x03FFFFFF-> User data end
+ | |-->0x04000000-> Data storage start
+ | |
+ +------------+-->0x08000000-> NOR end (Free end)
+ */
+ partition@0 {
+ label = "boot";
+ reg = <0x00000000 0x000c0000>; /* 768KB */
+ };
+
+ partition@1 {
+ label = "env1";
+ reg = <0x000c0000 0x00020000>; /* 128KB */
+ };
+
+ partition@2 {
+ label = "env2";
+ reg = <0x000e0000 0x00020000>; /* 128KB */
+ };
+
+ partition@3 {
+ label = "kernel";
+ reg = <0x00100000 0x00400000>; /* 4MB */
+ };
+
+ partition@4 {
+ label = "rootfs";
+ reg = <0x00500000 0x01000000>; /* 16MB */
+ };
+
+ partition@5 {
+ label = "user";
+ reg = <0x01500000 0x02b00000>; /* 43MB */
+ };
+
+ partition@6 {
+ label = "data";
+ reg = <0x04000000 0x04000000>; /* 64MB */
+ };
+ };
+};
+
+&mac {
+ dual_emac = <1>;
+};
+
+&cpsw_emac0 {
+ phy_id = <&davinci_mdio>, <0>;
+ dual_emac_res_vlan = <1>;
+};
+
+&cpsw_emac1 {
+ phy_id = <&davinci_mdio>, <1>;
+ dual_emac_res_vlan = <2>;
+};
+
+&mmc1 {
+ status = "okay";
+ vmmc-supply = <&ldo4_reg>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins>;
+ bus-width = <4>;
+ cd-gpios = <&gpio3 8 0>;
+ wp-gpios = <&gpio3 18 0>;
+};
+
+#include "tps65217.dtsi"
+
+&tps {
+ regulators {
+ dcdc1_reg: regulator@0 {
+ /* +1.5V voltage with ±4% tolerance */
+ regulator-min-microvolt = <1450000>;
+ regulator-max-microvolt = <1550000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ dcdc2_reg: regulator@1 {
+ /* VDD_MPU voltage limits 0.95V - 1.1V with ±4% tolerance */
+ regulator-name = "vdd_mpu";
+ regulator-min-microvolt = <915000>;
+ regulator-max-microvolt = <1140000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ dcdc3_reg: regulator@2 {
+ /* VDD_CORE voltage limits 0.95V - 1.1V with ±4% tolerance */
+ regulator-name = "vdd_core";
+ regulator-min-microvolt = <915000>;
+ regulator-max-microvolt = <1140000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo1_reg: regulator@3 {
+ /* +1.8V voltage with ±4% tolerance */
+ regulator-min-microvolt = <1750000>;
+ regulator-max-microvolt = <1870000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo2_reg: regulator@4 {
+ /* +3.3V voltage with ±4% tolerance */
+ regulator-min-microvolt = <3175000>;
+ regulator-max-microvolt = <3430000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo3_reg: regulator@5 {
+ /* +1.8V voltage with ±4% tolerance */
+ regulator-min-microvolt = <1750000>;
+ regulator-max-microvolt = <1870000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo4_reg: regulator@6 {
+ /* +3.3V voltage with ±4% tolerance */
+ regulator-min-microvolt = <3175000>;
+ regulator-max-microvolt = <3430000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/am33xx.dtsi b/arch/arm/boot/dts/am33xx.dtsi
index 7db3c81..0ca13ad 100644
--- a/arch/arm/boot/dts/am33xx.dtsi
+++ b/arch/arm/boot/dts/am33xx.dtsi
@@ -18,6 +18,9 @@
interrupt-parent = <&intc>;
aliases {
+ i2c0 = &i2c0;
+ i2c1 = &i2c1;
+ i2c2 = &i2c2;
serial0 = &uart0;
serial1 = &uart1;
serial2 = &uart2;
@@ -413,7 +416,7 @@
ti,hwmods = "usb_otg_hs";
status = "disabled";
- ctrl_mod: control@44e10000 {
+ usb_ctrl_mod: control@44e10000 {
compatible = "ti,am335x-usb-ctrl-module";
reg = <0x44e10620 0x10
0x44e10648 0x4>;
@@ -426,7 +429,7 @@
reg = <0x47401300 0x100>;
reg-names = "phy";
status = "disabled";
- ti,ctrl_mod = <&ctrl_mod>;
+ ti,ctrl_mod = <&usb_ctrl_mod>;
};
usb0: usb@47401000 {
@@ -474,7 +477,7 @@
reg = <0x47401b00 0x100>;
reg-names = "phy";
status = "disabled";
- ti,ctrl_mod = <&ctrl_mod>;
+ ti,ctrl_mod = <&usb_ctrl_mod>;
};
usb1: usb@47401800 {
@@ -674,6 +677,7 @@
reg = <0x44d00000 0x4000 /* M3 UMEM */
0x44d80000 0x2000>; /* M3 DMEM */
ti,hwmods = "wkup_m3";
+ ti,no-reset-on-init;
};
elm: elm@48080000 {
@@ -713,6 +717,7 @@
gpmc: gpmc@50000000 {
compatible = "ti,am3352-gpmc";
ti,hwmods = "gpmc";
+ ti,no-idle-on-init;
reg = <0x50000000 0x2000>;
interrupts = <100>;
gpmc,num-cs = <7>;
@@ -740,5 +745,33 @@
<&edma 5>;
dma-names = "tx", "rx";
};
+
+ mcasp0: mcasp@48038000 {
+ compatible = "ti,am33xx-mcasp-audio";
+ ti,hwmods = "mcasp0";
+ reg = <0x48038000 0x2000>,
+ <0x46000000 0x400000>;
+ reg-names = "mpu", "dat";
+ interrupts = <80>, <81>;
+ interrupts-names = "tx", "rx";
+ status = "disabled";
+ dmas = <&edma 8>,
+ <&edma 9>;
+ dma-names = "tx", "rx";
+ };
+
+ mcasp1: mcasp@4803C000 {
+ compatible = "ti,am33xx-mcasp-audio";
+ ti,hwmods = "mcasp1";
+ reg = <0x4803C000 0x2000>,
+ <0x46400000 0x400000>;
+ reg-names = "mpu", "dat";
+ interrupts = <82>, <83>;
+ interrupts-names = "tx", "rx";
+ status = "disabled";
+ dmas = <&edma 10>,
+ <&edma 11>;
+ dma-names = "tx", "rx";
+ };
};
};
diff --git a/arch/arm/boot/dts/am4372.dtsi b/arch/arm/boot/dts/am4372.dtsi
index a403172..974d103 100644
--- a/arch/arm/boot/dts/am4372.dtsi
+++ b/arch/arm/boot/dts/am4372.dtsi
@@ -18,7 +18,12 @@
aliases {
+ i2c0 = &i2c0;
+ i2c1 = &i2c1;
+ i2c2 = &i2c2;
serial0 = &uart0;
+ ethernet0 = &cpsw_emac0;
+ ethernet1 = &cpsw_emac1;
};
cpus {
@@ -39,11 +44,42 @@
<0x48240100 0x0100>;
};
+ l2-cache-controller@48242000 {
+ compatible = "arm,pl310-cache";
+ reg = <0x48242000 0x1000>;
+ cache-unified;
+ cache-level = <2>;
+ };
+
+ am43xx_pinmux: pinmux@44e10800 {
+ compatible = "pinctrl-single";
+ reg = <0x44e10800 0x31c>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-single,register-width = <32>;
+ pinctrl-single,function-mask = <0xffffffff>;
+ };
+
ocp {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
ranges;
+ ti,hwmods = "l3_main";
+
+ edma: edma@49000000 {
+ compatible = "ti,edma3";
+ ti,hwmods = "tpcc", "tptc0", "tptc1", "tptc2";
+ reg = <0x49000000 0x10000>,
+ <0x44e10f90 0x10>;
+ interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+ #dma-cells = <1>;
+ dma-channels = <64>;
+ ti,edma-regions = <4>;
+ ti,edma-slots = <256>;
+ };
uart0: serial@44e09000 {
compatible = "ti,am4372-uart","ti,omap2-uart";
@@ -92,6 +128,18 @@
status = "disabled";
};
+ mailbox: mailbox@480C8000 {
+ compatible = "ti,omap4-mailbox";
+ reg = <0x480C8000 0x200>;
+ interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "mailbox";
+ ti,mbox-num-users = <4>;
+ ti,mbox-num-fifos = <8>;
+ ti,mbox-names = "wkup_m3";
+ ti,mbox-data = <0 0 0 0>;
+ status = "disabled";
+ };
+
timer1: timer@44e31000 {
compatible = "ti,am4372-timer-1ms","ti,am335x-timer-1ms";
reg = <0x44e31000 0x400>;
@@ -203,7 +251,6 @@
reg = <0x44e35000 0x1000>;
interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
ti,hwmods = "wd_timer2";
- status = "disabled";
};
gpio0: gpio@44e07000 {
@@ -318,6 +365,40 @@
status = "disabled";
};
+ mmc1: mmc@48060000 {
+ compatible = "ti,omap4-hsmmc";
+ reg = <0x48060000 0x1000>;
+ ti,hwmods = "mmc1";
+ ti,dual-volt;
+ ti,needs-special-reset;
+ dmas = <&edma 24
+ &edma 25>;
+ dma-names = "tx", "rx";
+ interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ mmc2: mmc@481d8000 {
+ compatible = "ti,omap4-hsmmc";
+ reg = <0x481d8000 0x1000>;
+ ti,hwmods = "mmc2";
+ ti,needs-special-reset;
+ dmas = <&edma 2
+ &edma 3>;
+ dma-names = "tx", "rx";
+ interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ mmc3: mmc@47810000 {
+ compatible = "ti,omap4-hsmmc";
+ reg = <0x47810000 0x1000>;
+ ti,hwmods = "mmc3";
+ ti,needs-special-reset;
+ interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
spi1: spi@481a0000 {
compatible = "ti,am4372-mcspi","ti,omap4-mcspi";
reg = <0x481a0000 0x400>;
@@ -366,50 +447,173 @@
GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <1>;
ti,hwmods = "cpgmac0";
status = "disabled";
+ cpdma_channels = <8>;
+ ale_entries = <1024>;
+ bd_ram_size = <0x2000>;
+ no_bd_ram = <0>;
+ rx_descs = <64>;
+ mac_control = <0x20>;
+ slaves = <2>;
+ active_slave = <0>;
+ cpts_clock_mult = <0x80000000>;
+ cpts_clock_shift = <29>;
+ ranges;
+
+ davinci_mdio: mdio@4a101000 {
+ compatible = "ti,am4372-mdio","ti,davinci_mdio";
+ reg = <0x4a101000 0x100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ ti,hwmods = "davinci_mdio";
+ bus_freq = <1000000>;
+ status = "disabled";
+ };
+
+ cpsw_emac0: slave@4a100200 {
+ /* Filled in by U-Boot */
+ mac-address = [ 00 00 00 00 00 00 ];
+ };
+
+ cpsw_emac1: slave@4a100300 {
+ /* Filled in by U-Boot */
+ mac-address = [ 00 00 00 00 00 00 ];
+ };
};
epwmss0: epwmss@48300000 {
compatible = "ti,am4372-pwmss","ti,am33xx-pwmss";
reg = <0x48300000 0x10>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
ti,hwmods = "epwmss0";
status = "disabled";
+
+ ecap0: ecap@48300100 {
+ compatible = "ti,am4372-ecap","ti,am33xx-ecap";
+ reg = <0x48300100 0x80>;
+ ti,hwmods = "ecap0";
+ status = "disabled";
+ };
+
+ ehrpwm0: ehrpwm@48300200 {
+ compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+ reg = <0x48300200 0x80>;
+ ti,hwmods = "ehrpwm0";
+ status = "disabled";
+ };
};
epwmss1: epwmss@48302000 {
compatible = "ti,am4372-pwmss","ti,am33xx-pwmss";
reg = <0x48302000 0x10>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
ti,hwmods = "epwmss1";
status = "disabled";
+
+ ecap1: ecap@48302100 {
+ compatible = "ti,am4372-ecap","ti,am33xx-ecap";
+ reg = <0x48302100 0x80>;
+ ti,hwmods = "ecap1";
+ status = "disabled";
+ };
+
+ ehrpwm1: ehrpwm@48302200 {
+ compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+ reg = <0x48302200 0x80>;
+ ti,hwmods = "ehrpwm1";
+ status = "disabled";
+ };
};
epwmss2: epwmss@48304000 {
compatible = "ti,am4372-pwmss","ti,am33xx-pwmss";
reg = <0x48304000 0x10>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
ti,hwmods = "epwmss2";
status = "disabled";
+
+ ecap2: ecap@48304100 {
+ compatible = "ti,am4372-ecap","ti,am33xx-ecap";
+ reg = <0x48304100 0x80>;
+ ti,hwmods = "ecap2";
+ status = "disabled";
+ };
+
+ ehrpwm2: ehrpwm@48304200 {
+ compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+ reg = <0x48304200 0x80>;
+ ti,hwmods = "ehrpwm2";
+ status = "disabled";
+ };
};
epwmss3: epwmss@48306000 {
compatible = "ti,am4372-pwmss","ti,am33xx-pwmss";
reg = <0x48306000 0x10>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
ti,hwmods = "epwmss3";
status = "disabled";
+
+ ehrpwm3: ehrpwm@48306200 {
+ compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+ reg = <0x48306200 0x80>;
+ ti,hwmods = "ehrpwm3";
+ status = "disabled";
+ };
};
epwmss4: epwmss@48308000 {
compatible = "ti,am4372-pwmss","ti,am33xx-pwmss";
reg = <0x48308000 0x10>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
ti,hwmods = "epwmss4";
status = "disabled";
+
+ ehrpwm4: ehrpwm@48308200 {
+ compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+ reg = <0x48308200 0x80>;
+ ti,hwmods = "ehrpwm4";
+ status = "disabled";
+ };
};
epwmss5: epwmss@4830a000 {
compatible = "ti,am4372-pwmss","ti,am33xx-pwmss";
reg = <0x4830a000 0x10>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
ti,hwmods = "epwmss5";
status = "disabled";
+
+ ehrpwm5: ehrpwm@4830a200 {
+ compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+ reg = <0x4830a200 0x80>;
+ ti,hwmods = "ehrpwm5";
+ status = "disabled";
+ };
+ };
+
+ sham: sham@53100000 {
+ compatible = "ti,omap5-sham";
+ ti,hwmods = "sham";
+ reg = <0x53100000 0x300>;
+ dmas = <&edma 36>;
+ dma-names = "rx";
+ interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
};
aes: aes@53501000 {
@@ -417,6 +621,9 @@
ti,hwmods = "aes";
reg = <0x53501000 0xa0>;
interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
+ dmas = <&edma 6
+ &edma 5>;
+ dma-names = "tx", "rx";
};
des: des@53701000 {
@@ -424,6 +631,37 @@
ti,hwmods = "des";
reg = <0x53701000 0xa0>;
interrupts = <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>;
+ dmas = <&edma 34
+ &edma 33>;
+ dma-names = "tx", "rx";
+ };
+
+ mcasp0: mcasp@48038000 {
+ compatible = "ti,am33xx-mcasp-audio";
+ ti,hwmods = "mcasp0";
+ reg = <0x48038000 0x2000>,
+ <0x46000000 0x400000>;
+ reg-names = "mpu", "dat";
+ interrupts = <80>, <81>;
+ interrupts-names = "tx", "rx";
+ status = "disabled";
+ dmas = <&edma 8>,
+ <&edma 9>;
+ dma-names = "tx", "rx";
+ };
+
+ mcasp1: mcasp@4803C000 {
+ compatible = "ti,am33xx-mcasp-audio";
+ ti,hwmods = "mcasp1";
+ reg = <0x4803C000 0x2000>,
+ <0x46400000 0x400000>;
+ reg-names = "mpu", "dat";
+ interrupts = <82>, <83>;
+ interrupts-names = "tx", "rx";
+ status = "disabled";
+ dmas = <&edma 10>,
+ <&edma 11>;
+ dma-names = "tx", "rx";
};
};
};
diff --git a/arch/arm/boot/dts/am43x-epos-evm.dts b/arch/arm/boot/dts/am43x-epos-evm.dts
index 74174d4..fbf9c4c 100644
--- a/arch/arm/boot/dts/am43x-epos-evm.dts
+++ b/arch/arm/boot/dts/am43x-epos-evm.dts
@@ -11,8 +11,176 @@
/dts-v1/;
#include "am4372.dtsi"
+#include <dt-bindings/pinctrl/am43xx.h>
+#include <dt-bindings/gpio/gpio.h>
/ {
model = "TI AM43x EPOS EVM";
compatible = "ti,am43x-epos-evm","ti,am4372","ti,am43";
+
+ vmmcsd_fixed: fixedregulator-sd {
+ compatible = "regulator-fixed";
+ regulator-name = "vmmcsd_fixed";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ enable-active-high;
+ };
+
+ am43xx_pinmux: pinmux@44e10800 {
+ cpsw_default: cpsw_default {
+ pinctrl-single,pins = <
+ /* Slave 1 */
+ 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_crs.rmii1_crs */
+ 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxerr.rmii1_rxerr */
+ 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* mii1_txen.rmii1_txen */
+ 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxdv.rmii1_rxdv */
+ 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* mii1_txd1.rmii1_txd1 */
+ 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* mii1_txd0.rmii1_txd0 */
+ 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxd1.rmii1_rxd1 */
+ 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxd0.rmii1_rxd0 */
+ 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii1_refclk.rmii1_refclk */
+ >;
+ };
+
+ cpsw_sleep: cpsw_sleep {
+ pinctrl-single,pins = <
+ /* Slave 1 reset value */
+ 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ >;
+ };
+
+ davinci_mdio_default: davinci_mdio_default {
+ pinctrl-single,pins = <
+ /* MDIO */
+ 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */
+ 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */
+ >;
+ };
+
+ davinci_mdio_sleep: davinci_mdio_sleep {
+ pinctrl-single,pins = <
+ /* MDIO reset value */
+ 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ >;
+ };
+
+ i2c0_pins: pinmux_i2c0_pins {
+ pinctrl-single,pins = <
+ 0x188 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* i2c0_sda.i2c0_sda */
+ 0x18c (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* i2c0_scl.i2c0_scl */
+ >;
+ };
+ };
+
+ matrix_keypad: matrix_keypad@0 {
+ compatible = "gpio-matrix-keypad";
+ debounce-delay-ms = <5>;
+ col-scan-delay-us = <2>;
+
+ row-gpios = <&gpio0 12 GPIO_ACTIVE_HIGH /* Bank0, pin12 */
+ &gpio0 13 GPIO_ACTIVE_HIGH /* Bank0, pin13 */
+ &gpio0 14 GPIO_ACTIVE_HIGH /* Bank0, pin14 */
+ &gpio0 15 GPIO_ACTIVE_HIGH>; /* Bank0, pin15 */
+
+ col-gpios = <&gpio3 9 GPIO_ACTIVE_HIGH /* Bank3, pin9 */
+ &gpio3 10 GPIO_ACTIVE_HIGH /* Bank3, pin10 */
+ &gpio2 18 GPIO_ACTIVE_HIGH /* Bank2, pin18 */
+ &gpio2 19 GPIO_ACTIVE_HIGH>; /* Bank2, pin19 */
+
+ linux,keymap = <0x00000201 /* P1 */
+ 0x01000204 /* P4 */
+ 0x02000207 /* P7 */
+ 0x0300020a /* NUMERIC_STAR */
+ 0x00010202 /* P2 */
+ 0x01010205 /* P5 */
+ 0x02010208 /* P8 */
+ 0x03010200 /* P0 */
+ 0x00020203 /* P3 */
+ 0x01020206 /* P6 */
+ 0x02020209 /* P9 */
+ 0x0302020b /* NUMERIC_POUND */
+ 0x00030067 /* UP */
+ 0x0103006a /* RIGHT */
+ 0x0203006c /* DOWN */
+ 0x03030069>; /* LEFT */
+ };
+};
+
+&mmc1 {
+ status = "okay";
+ vmmc-supply = <&vmmcsd_fixed>;
+ bus-width = <4>;
+};
+
+&mac {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&cpsw_default>;
+ pinctrl-1 = <&cpsw_sleep>;
+ status = "okay";
+};
+
+&davinci_mdio {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&davinci_mdio_default>;
+ pinctrl-1 = <&davinci_mdio_sleep>;
+ status = "okay";
+};
+
+&cpsw_emac0 {
+ phy_id = <&davinci_mdio>, <16>;
+ phy-mode = "rmii";
+};
+
+&cpsw_emac1 {
+ phy_id = <&davinci_mdio>, <1>;
+ phy-mode = "rmii";
+};
+
+&i2c0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins>;
+
+ at24@50 {
+ compatible = "at24,24c256";
+ pagesize = <64>;
+ reg = <0x50>;
+ };
+
+ pixcir_ts@5c {
+ compatible = "pixcir,pixcir_ts";
+ reg = <0x5c>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <17 0>;
+
+ attb-gpio = <&gpio1 17 GPIO_ACTIVE_HIGH>;
+
+ x-size = <1024>;
+ y-size = <768>;
+ };
+};
+
+&gpio0 {
+ status = "okay";
+};
+
+&gpio1 {
+ status = "okay";
+};
+
+&gpio2 {
+ status = "okay";
+};
+
+&gpio3 {
+ status = "okay";
};
diff --git a/arch/arm/boot/dts/dra7-evm.dts b/arch/arm/boot/dts/dra7-evm.dts
index 3abf5f4..5babba0 100644
--- a/arch/arm/boot/dts/dra7-evm.dts
+++ b/arch/arm/boot/dts/dra7-evm.dts
@@ -269,3 +269,7 @@
vmmc-supply = <&mmc2_3v3>;
bus-width = <8>;
};
+
+&cpu0 {
+ cpu0-supply = <&smps123_reg>;
+};
diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi
index c01ef76..d0df4c4 100644
--- a/arch/arm/boot/dts/dra7.dtsi
+++ b/arch/arm/boot/dts/dra7.dtsi
@@ -20,6 +20,11 @@
interrupt-parent = <&gic>;
aliases {
+ i2c0 = &i2c1;
+ i2c1 = &i2c2;
+ i2c2 = &i2c3;
+ i2c3 = &i2c4;
+ i2c4 = &i2c5;
serial0 = &uart1;
serial1 = &uart2;
serial2 = &uart3;
@@ -32,10 +37,16 @@
#address-cells = <1>;
#size-cells = <0>;
- cpu@0 {
+ cpu0: cpu@0 {
device_type = "cpu";
compatible = "arm,cortex-a15";
reg = <0>;
+
+ operating-points = <
+ /* kHz uV */
+ 1000000 1060000
+ 1176000 1160000
+ >;
};
cpu@1 {
device_type = "cpu";
diff --git a/arch/arm/boot/dts/omap3-beagle.dts b/arch/arm/boot/dts/omap3-beagle.dts
index 7669c16..fa532aa 100644
--- a/arch/arm/boot/dts/omap3-beagle.dts
+++ b/arch/arm/boot/dts/omap3-beagle.dts
@@ -173,6 +173,8 @@
&usb_otg_hs {
interface-type = <0>;
usb-phy = <&usb2_phy>;
+ phys = <&usb2_phy>;
+ phy-names = "usb2-phy";
mode = <3>;
power = <50>;
};
diff --git a/arch/arm/boot/dts/omap3-gta04.dts b/arch/arm/boot/dts/omap3-gta04.dts
index a84684a..b9b55c9 100644
--- a/arch/arm/boot/dts/omap3-gta04.dts
+++ b/arch/arm/boot/dts/omap3-gta04.dts
@@ -131,6 +131,8 @@
&usb_otg_hs {
interface-type = <0>;
usb-phy = <&usb2_phy>;
+ phys = <&usb2_phy>;
+ phy-names = "usb2-phy";
mode = <3>;
power = <50>;
};
diff --git a/arch/arm/boot/dts/omap3-n900.dts b/arch/arm/boot/dts/omap3-n900.dts
index d64fa04..c4f20bf 100644
--- a/arch/arm/boot/dts/omap3-n900.dts
+++ b/arch/arm/boot/dts/omap3-n900.dts
@@ -26,9 +26,116 @@
reg = <0x80000000 0x10000000>; /* 256 MB */
};
+ gpio_keys {
+ compatible = "gpio-keys";
+
+ camera_lens_cover {
+ label = "Camera Lens Cover";
+ gpios = <&gpio4 14 GPIO_ACTIVE_LOW>; /* 110 */
+ linux,input-type = <5>; /* EV_SW */
+ linux,code = <0x09>; /* SW_CAMERA_LENS_COVER */
+ gpio-key,wakeup;
+ };
+
+ camera_focus {
+ label = "Camera Focus";
+ gpios = <&gpio3 4 GPIO_ACTIVE_LOW>; /* 68 */
+ linux,code = <0x210>; /* KEY_CAMERA_FOCUS */
+ gpio-key,wakeup;
+ };
+
+ camera_capture {
+ label = "Camera Capture";
+ gpios = <&gpio3 5 GPIO_ACTIVE_LOW>; /* 69 */
+ linux,code = <0xd4>; /* KEY_CAMERA */
+ gpio-key,wakeup;
+ };
+
+ lock_button {
+ label = "Lock Button";
+ gpios = <&gpio4 17 GPIO_ACTIVE_LOW>; /* 113 */
+ linux,code = <0x98>; /* KEY_SCREENLOCK */
+ gpio-key,wakeup;
+ };
+
+ keypad_slide {
+ label = "Keypad Slide";
+ gpios = <&gpio3 7 GPIO_ACTIVE_LOW>; /* 71 */
+ linux,input-type = <5>; /* EV_SW */
+ linux,code = <0x0a>; /* SW_KEYPAD_SLIDE */
+ gpio-key,wakeup;
+ };
+
+ proximity_sensor {
+ label = "Proximity Sensor";
+ gpios = <&gpio3 25 GPIO_ACTIVE_HIGH>; /* 89 */
+ linux,input-type = <5>; /* EV_SW */
+ linux,code = <0x0b>; /* SW_FRONT_PROXIMITY */
+ };
+ };
+
+};
+
+&omap3_pmx_core {
+ pinctrl-names = "default";
+
+ uart2_pins: pinmux_uart2_pins {
+ pinctrl-single,pins = <
+ 0x14a (PIN_INPUT | MUX_MODE0) /* uart2_rx */
+ 0x148 (PIN_OUTPUT | MUX_MODE0) /* uart2_tx */
+ >;
+ };
+
+ uart3_pins: pinmux_uart3_pins {
+ pinctrl-single,pins = <
+ 0x16e (PIN_INPUT | MUX_MODE0) /* uart3_rx */
+ 0x170 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx */
+ >;
+ };
+
+ i2c1_pins: pinmux_i2c1_pins {
+ pinctrl-single,pins = <
+ 0x18a (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl */
+ 0x18c (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda */
+ >;
+ };
+
+ i2c2_pins: pinmux_i2c2_pins {
+ pinctrl-single,pins = <
+ 0x18e (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c2_scl */
+ 0x190 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c2_sda */
+ >;
+ };
+
+ i2c3_pins: pinmux_i2c3_pins {
+ pinctrl-single,pins = <
+ 0x192 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_scl */
+ 0x194 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_sda */
+ >;
+ };
+
+ mmc1_pins: pinmux_mmc1_pins {
+ pinctrl-single,pins = <
+ 0x114 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk */
+ 0x116 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd */
+ 0x118 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0 */
+ 0x11a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1 */
+ 0x11c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2 */
+ 0x11e (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3 */
+ >;
+ };
+
+ display_pins: pinmux_display_pins {
+ pinctrl-single,pins = <
+ 0x0d4 (PIN_OUTPUT | MUX_MODE4) /* RX51_LCD_RESET_GPIO */
+ >;
+ };
};
&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins>;
+
clock-frequency = <2200000>;
twl: twl@48 {
@@ -39,6 +146,98 @@
};
#include "twl4030.dtsi"
+#include "twl4030_omap3.dtsi"
+
+&vaux1 {
+ regulator-name = "V28";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on; /* due battery cover sensor */
+};
+
+&vaux2 {
+ regulator-name = "VCSI";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+};
+
+&vaux3 {
+ regulator-name = "VMMC2_30";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <3000000>;
+};
+
+&vaux4 {
+ regulator-name = "VCAM_ANA_28";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+};
+
+&vmmc1 {
+ regulator-name = "VMMC1";
+ regulator-min-microvolt = <1850000>;
+ regulator-max-microvolt = <3150000>;
+};
+
+&vmmc2 {
+ regulator-name = "V28_A";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on; /* due VIO leak to AIC34 VDDs */
+};
+
+&vpll1 {
+ regulator-name = "VPLL";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+};
+
+&vpll2 {
+ regulator-name = "VSDI_CSI";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+};
+
+&vsim {
+ regulator-name = "VMMC2_IO_18";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+};
+
+&vio {
+ regulator-name = "VIO";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+};
+
+&vintana1 {
+ regulator-name = "VINTANA1";
+ /* fixed to 1500000 */
+ regulator-always-on;
+};
+
+&vintana2 {
+ regulator-name = "VINTANA2";
+ regulator-min-microvolt = <2750000>;
+ regulator-max-microvolt = <2750000>;
+ regulator-always-on;
+};
+
+&vintdig {
+ regulator-name = "VINTDIG";
+ /* fixed to 1500000 */
+ regulator-always-on;
+};
+
+&twl {
+ twl_audio: audio {
+ compatible = "ti,twl4030-audio";
+ ti,enable-vibra = <1>;
+ };
+};
&twl_gpio {
ti,pullups = <0x0>;
@@ -46,15 +245,117 @@
};
&i2c2 {
- clock-frequency = <400000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins>;
+
+ clock-frequency = <100000>;
+
+ tlv320aic3x: tlv320aic3x@18 {
+ compatible = "ti,tlv320aic3x";
+ reg = <0x18>;
+ gpio-reset = <&gpio2 28 GPIO_ACTIVE_HIGH>; /* 60 */
+ ai3x-gpio-func = <
+ 0 /* AIC3X_GPIO1_FUNC_DISABLED */
+ 5 /* AIC3X_GPIO2_FUNC_DIGITAL_MIC_INPUT */
+ >;
+
+ AVDD-supply = <&vmmc2>;
+ DRVDD-supply = <&vmmc2>;
+ IOVDD-supply = <&vio>;
+ DVDD-supply = <&vio>;
+ };
+
+ tlv320aic3x_aux: tlv320aic3x@19 {
+ compatible = "ti,tlv320aic3x";
+ reg = <0x19>;
+ gpio-reset = <&gpio2 28 GPIO_ACTIVE_HIGH>; /* 60 */
+
+ AVDD-supply = <&vmmc2>;
+ DRVDD-supply = <&vmmc2>;
+ IOVDD-supply = <&vio>;
+ DVDD-supply = <&vio>;
+ };
+
+ lp5523: lp5523@32 {
+ compatible = "national,lp5523";
+ reg = <0x32>;
+ clock-mode = /bits/ 8 <0>; /* LP55XX_CLOCK_AUTO */
+ enable-gpio = <&gpio2 9 GPIO_ACTIVE_HIGH>; /* 41 */
+
+ chan0 {
+ chan-name = "lp5523:kb1";
+ led-cur = /bits/ 8 <50>;
+ max-cur = /bits/ 8 <100>;
+ };
+
+ chan1 {
+ chan-name = "lp5523:kb2";
+ led-cur = /bits/ 8 <50>;
+ max-cur = /bits/ 8 <100>;
+ };
+
+ chan2 {
+ chan-name = "lp5523:kb3";
+ led-cur = /bits/ 8 <50>;
+ max-cur = /bits/ 8 <100>;
+ };
+
+ chan3 {
+ chan-name = "lp5523:kb4";
+ led-cur = /bits/ 8 <50>;
+ max-cur = /bits/ 8 <100>;
+ };
+
+ chan4 {
+ chan-name = "lp5523:b";
+ led-cur = /bits/ 8 <50>;
+ max-cur = /bits/ 8 <100>;
+ };
+
+ chan5 {
+ chan-name = "lp5523:g";
+ led-cur = /bits/ 8 <50>;
+ max-cur = /bits/ 8 <100>;
+ };
+
+ chan6 {
+ chan-name = "lp5523:r";
+ led-cur = /bits/ 8 <50>;
+ max-cur = /bits/ 8 <100>;
+ };
+
+ chan7 {
+ chan-name = "lp5523:kb5";
+ led-cur = /bits/ 8 <50>;
+ max-cur = /bits/ 8 <100>;
+ };
+
+ chan8 {
+ chan-name = "lp5523:kb6";
+ led-cur = /bits/ 8 <50>;
+ max-cur = /bits/ 8 <100>;
+ };
+ };
+
+ bq27200: bq27200@55 {
+ compatible = "ti,bq27200";
+ reg = <0x55>;
+ };
};
&i2c3 {
- clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c3_pins>;
+
+ clock-frequency = <400000>;
};
&mmc1 {
- status = "disabled";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins>;
+ vmmc-supply = <&vmmc1>;
+ bus-width = <4>;
+ cd-gpios = <&gpio6 0 GPIO_ACTIVE_HIGH>; /* 160 */
};
&mmc2 {
@@ -65,6 +366,78 @@
status = "disabled";
};
+&gpmc {
+ ranges = <0 0 0x04000000 0x10000000>; /* 256MB */
+
+ /* gpio-irq for dma: 65 */
+
+ onenand@0,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0 0 0x10000000>;
+
+ gpmc,sync-read;
+ gpmc,sync-write;
+ gpmc,burst-length = <16>;
+ gpmc,burst-read;
+ gpmc,burst-wrap;
+ gpmc,burst-write;
+ gpmc,device-width = <2>; /* GPMC_DEVWIDTH_16BIT */
+ gpmc,mux-add-data = <2>; /* GPMC_MUX_AD */
+ gpmc,cs-on-ns = <0>;
+ gpmc,cs-rd-off-ns = <87>;
+ gpmc,cs-wr-off-ns = <87>;
+ gpmc,adv-on-ns = <0>;
+ gpmc,adv-rd-off-ns = <10>;
+ gpmc,adv-wr-off-ns = <10>;
+ gpmc,oe-on-ns = <15>;
+ gpmc,oe-off-ns = <87>;
+ gpmc,we-on-ns = <0>;
+ gpmc,we-off-ns = <87>;
+ gpmc,rd-cycle-ns = <112>;
+ gpmc,wr-cycle-ns = <112>;
+ gpmc,access-ns = <81>;
+ gpmc,page-burst-access-ns = <15>;
+ gpmc,bus-turnaround-ns = <0>;
+ gpmc,cycle2cycle-delay-ns = <0>;
+ gpmc,wait-monitoring-ns = <0>;
+ gpmc,clk-activation-ns = <5>;
+ gpmc,wr-data-mux-bus-ns = <30>;
+ gpmc,wr-access-ns = <81>;
+ gpmc,sync-clk-ps = <15000>;
+
+ /*
+ * MTD partition table corresponding to Nokia's
+ * Maemo 5 (Fremantle) release.
+ */
+ partition@0 {
+ label = "bootloader";
+ reg = <0x00000000 0x00020000>;
+ read-only;
+ };
+ partition@1 {
+ label = "config";
+ reg = <0x00020000 0x00060000>;
+ };
+ partition@2 {
+ label = "log";
+ reg = <0x00080000 0x00040000>;
+ };
+ partition@3 {
+ label = "kernel";
+ reg = <0x000c0000 0x00200000>;
+ };
+ partition@4 {
+ label = "initfs";
+ reg = <0x002c0000 0x00200000>;
+ };
+ partition@5 {
+ label = "rootfs";
+ reg = <0x004c0000 0x0fb40000>;
+ };
+ };
+};
+
&mcspi1 {
/*
* For some reason, touchscreen is necessary for screen to work at
@@ -81,12 +454,31 @@
compatible = "acx565akm";
spi-max-frequency = <6000000>;
reg = <2>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&display_pins>;
};
};
&usb_otg_hs {
interface-type = <0>;
usb-phy = <&usb2_phy>;
+ phys = <&usb2_phy>;
+ phy-names = "usb2-phy";
mode = <2>;
power = <50>;
};
+
+&uart1 {
+ status = "disabled";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pins>;
+};
diff --git a/arch/arm/boot/dts/omap3.dtsi b/arch/arm/boot/dts/omap3.dtsi
index f275bee..f3a0c26 100644
--- a/arch/arm/boot/dts/omap3.dtsi
+++ b/arch/arm/boot/dts/omap3.dtsi
@@ -19,6 +19,9 @@
interrupt-parent = <&intc>;
aliases {
+ i2c0 = &i2c1;
+ i2c1 = &i2c2;
+ i2c2 = &i2c3;
serial0 = &uart1;
serial1 = &uart2;
serial2 = &uart3;
@@ -37,6 +40,7 @@
pmu {
compatible = "arm,cortex-a8-pmu";
+ reg = <0x54000000 0x800000>;
interrupts = <3>;
ti,hwmods = "debugss";
};
@@ -71,6 +75,8 @@
*/
ocp {
compatible = "simple-bus";
+ reg = <0x68000000 0x10000>;
+ interrupts = <9 10>;
#address-cells = <1>;
#size-cells = <1>;
ranges;
@@ -193,24 +199,40 @@
uart1: serial@4806a000 {
compatible = "ti,omap3-uart";
+ reg = <0x4806a000 0x2000>;
+ interrupts = <72>;
+ dmas = <&sdma 49 &sdma 50>;
+ dma-names = "tx", "rx";
ti,hwmods = "uart1";
clock-frequency = <48000000>;
};
uart2: serial@4806c000 {
compatible = "ti,omap3-uart";
+ reg = <0x4806c000 0x400>;
+ interrupts = <73>;
+ dmas = <&sdma 51 &sdma 52>;
+ dma-names = "tx", "rx";
ti,hwmods = "uart2";
clock-frequency = <48000000>;
};
uart3: serial@49020000 {
compatible = "ti,omap3-uart";
+ reg = <0x49020000 0x400>;
+ interrupts = <74>;
+ dmas = <&sdma 53 &sdma 54>;
+ dma-names = "tx", "rx";
ti,hwmods = "uart3";
clock-frequency = <48000000>;
};
i2c1: i2c@48070000 {
compatible = "ti,omap3-i2c";
+ reg = <0x48070000 0x80>;
+ interrupts = <56>;
+ dmas = <&sdma 27 &sdma 28>;
+ dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
ti,hwmods = "i2c1";
@@ -218,6 +240,10 @@
i2c2: i2c@48072000 {
compatible = "ti,omap3-i2c";
+ reg = <0x48072000 0x80>;
+ interrupts = <57>;
+ dmas = <&sdma 29 &sdma 30>;
+ dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
ti,hwmods = "i2c2";
@@ -225,6 +251,10 @@
i2c3: i2c@48060000 {
compatible = "ti,omap3-i2c";
+ reg = <0x48060000 0x80>;
+ interrupts = <61>;
+ dmas = <&sdma 25 &sdma 26>;
+ dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
ti,hwmods = "i2c3";
@@ -232,6 +262,8 @@
mcspi1: spi@48098000 {
compatible = "ti,omap2-mcspi";
+ reg = <0x48098000 0x100>;
+ interrupts = <65>;
#address-cells = <1>;
#size-cells = <0>;
ti,hwmods = "mcspi1";
@@ -250,6 +282,8 @@
mcspi2: spi@4809a000 {
compatible = "ti,omap2-mcspi";
+ reg = <0x4809a000 0x100>;
+ interrupts = <66>;
#address-cells = <1>;
#size-cells = <0>;
ti,hwmods = "mcspi2";
@@ -263,6 +297,8 @@
mcspi3: spi@480b8000 {
compatible = "ti,omap2-mcspi";
+ reg = <0x480b8000 0x100>;
+ interrupts = <91>;
#address-cells = <1>;
#size-cells = <0>;
ti,hwmods = "mcspi3";
@@ -276,6 +312,8 @@
mcspi4: spi@480ba000 {
compatible = "ti,omap2-mcspi";
+ reg = <0x480ba000 0x100>;
+ interrupts = <48>;
#address-cells = <1>;
#size-cells = <0>;
ti,hwmods = "mcspi4";
@@ -284,8 +322,17 @@
dma-names = "tx0", "rx0";
};
+ hdqw1w: 1w@480b2000 {
+ compatible = "ti,omap3-1w";
+ reg = <0x480b2000 0x1000>;
+ interrupts = <58>;
+ ti,hwmods = "hdq1w";
+ };
+
mmc1: mmc@4809c000 {
compatible = "ti,omap3-hsmmc";
+ reg = <0x4809c000 0x200>;
+ interrupts = <83>;
ti,hwmods = "mmc1";
ti,dual-volt;
dmas = <&sdma 61>, <&sdma 62>;
@@ -294,6 +341,8 @@
mmc2: mmc@480b4000 {
compatible = "ti,omap3-hsmmc";
+ reg = <0x480b4000 0x200>;
+ interrupts = <86>;
ti,hwmods = "mmc2";
dmas = <&sdma 47>, <&sdma 48>;
dma-names = "tx", "rx";
@@ -301,6 +350,8 @@
mmc3: mmc@480ad000 {
compatible = "ti,omap3-hsmmc";
+ reg = <0x480ad000 0x200>;
+ interrupts = <94>;
ti,hwmods = "mmc3";
dmas = <&sdma 77>, <&sdma 78>;
dma-names = "tx", "rx";
@@ -308,6 +359,7 @@
wdt2: wdt@48314000 {
compatible = "ti,omap3-wdt";
+ reg = <0x48314000 0x80>;
ti,hwmods = "wd_timer2";
};
diff --git a/arch/arm/boot/dts/omap36xx.dtsi b/arch/arm/boot/dts/omap36xx.dtsi
index f8b3765..380c22e 100644
--- a/arch/arm/boot/dts/omap36xx.dtsi
+++ b/arch/arm/boot/dts/omap36xx.dtsi
@@ -31,6 +31,10 @@
ocp {
uart4: serial@49042000 {
compatible = "ti,omap3-uart";
+ reg = <0x49042000 0x400>;
+ interrupts = <80>;
+ dmas = <&sdma 81 &sdma 82>;
+ dma-names = "tx", "rx";
ti,hwmods = "uart4";
clock-frequency = <48000000>;
};
diff --git a/arch/arm/boot/dts/omap4-panda-es.dts b/arch/arm/boot/dts/omap4-panda-es.dts
index 56c4354..816d1c9 100644
--- a/arch/arm/boot/dts/omap4-panda-es.dts
+++ b/arch/arm/boot/dts/omap4-panda-es.dts
@@ -62,3 +62,7 @@
gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
};
};
+
+&gpio1 {
+ ti,no-reset-on-init;
+};
diff --git a/arch/arm/boot/dts/omap4.dtsi b/arch/arm/boot/dts/omap4.dtsi
index 17a3618..e8d97b4 100644
--- a/arch/arm/boot/dts/omap4.dtsi
+++ b/arch/arm/boot/dts/omap4.dtsi
@@ -17,6 +17,10 @@
interrupt-parent = <&gic>;
aliases {
+ i2c0 = &i2c1;
+ i2c1 = &i2c2;
+ i2c2 = &i2c3;
+ i2c3 = &i2c4;
serial0 = &uart1;
serial1 = &uart2;
serial2 = &uart3;
@@ -218,6 +222,7 @@
gpmc,num-cs = <8>;
gpmc,num-waitpins = <4>;
ti,hwmods = "gpmc";
+ ti,no-idle-on-init;
};
uart1: serial@4806a000 {
@@ -496,6 +501,7 @@
reg = <0x4c000000 0x100>;
interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
ti,hwmods = "emif1";
+ ti,no-idle-on-init;
phy-type = <1>;
hw-caps-read-idle-ctrl;
hw-caps-ll-interface;
@@ -507,6 +513,7 @@
reg = <0x4d000000 0x100>;
interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
ti,hwmods = "emif2";
+ ti,no-idle-on-init;
phy-type = <1>;
hw-caps-read-idle-ctrl;
hw-caps-ll-interface;
diff --git a/arch/arm/boot/dts/omap5-uevm.dts b/arch/arm/boot/dts/omap5-uevm.dts
index d784b3a..002fa70 100644
--- a/arch/arm/boot/dts/omap5-uevm.dts
+++ b/arch/arm/boot/dts/omap5-uevm.dts
@@ -62,7 +62,6 @@
pinctrl-0 = <
&twl6040_pins
&mcpdm_pins
- &dmic_pins
&mcbsp1_pins
&mcbsp2_pins
&usbhost_pins
@@ -71,7 +70,7 @@
twl6040_pins: pinmux_twl6040_pins {
pinctrl-single,pins = <
- 0x18a (PIN_OUTPUT | MUX_MODE6) /* perslimbus2_clock.gpio5_145 */
+ 0x17e (PIN_OUTPUT | MUX_MODE6) /* mcspi1_somi.gpio5_141 */
>;
};
@@ -85,15 +84,6 @@
>;
};
- dmic_pins: pinmux_dmic_pins {
- pinctrl-single,pins = <
- 0x144 (PIN_INPUT | MUX_MODE0) /* abedmic_din1.abedmic_din1 */
- 0x146 (PIN_INPUT | MUX_MODE0) /* abedmic_din2.abedmic_din2 */
- 0x148 (PIN_INPUT | MUX_MODE0) /* abedmic_din3.abedmic_din3 */
- 0x14a (PIN_OUTPUT | MUX_MODE0) /* abedmic_clk1.abedmic_clk1 */
- >;
- };
-
mcbsp1_pins: pinmux_mcbsp1_pins {
pinctrl-single,pins = <
0x14c (PIN_INPUT | MUX_MODE1) /* abedmic_clk2.abemcbsp1_fsx */
@@ -131,25 +121,25 @@
0xbc (PIN_INPUT | MUX_MODE0) /* mcspi2_clk */
0xbe (PIN_INPUT | MUX_MODE0) /* mcspi2_simo */
0xc0 (PIN_INPUT_PULLUP | MUX_MODE0) /* mcspi2_somi */
- 0xc2 (PIN_OUTPUT | MUX_MODE0) /* mcspi2_cs */
+ 0xc2 (PIN_OUTPUT | MUX_MODE0) /* mcspi2_cs0 */
>;
};
mcspi3_pins: pinmux_mcspi3_pins {
pinctrl-single,pins = <
- 0x78 (PIN_INPUT | MUX_MODE1) /* mcspi2_somi */
- 0x7a (PIN_INPUT | MUX_MODE1) /* mcspi2_cs */
- 0x7c (PIN_INPUT | MUX_MODE1) /* mcspi2_simo */
- 0x7e (PIN_INPUT | MUX_MODE1) /* mcspi2_clk */
+ 0x78 (PIN_INPUT | MUX_MODE1) /* mcspi3_somi */
+ 0x7a (PIN_INPUT | MUX_MODE1) /* mcspi3_cs0 */
+ 0x7c (PIN_INPUT | MUX_MODE1) /* mcspi3_simo */
+ 0x7e (PIN_INPUT | MUX_MODE1) /* mcspi3_clk */
>;
};
mcspi4_pins: pinmux_mcspi4_pins {
pinctrl-single,pins = <
- 0x164 (PIN_INPUT | MUX_MODE1) /* mcspi2_clk */
- 0x168 (PIN_INPUT | MUX_MODE1) /* mcspi2_simo */
- 0x16a (PIN_INPUT | MUX_MODE1) /* mcspi2_somi */
- 0x16c (PIN_INPUT | MUX_MODE1) /* mcspi2_cs */
+ 0x164 (PIN_INPUT | MUX_MODE1) /* mcspi4_clk */
+ 0x168 (PIN_INPUT | MUX_MODE1) /* mcspi4_simo */
+ 0x16a (PIN_INPUT | MUX_MODE1) /* mcspi4_somi */
+ 0x16c (PIN_INPUT | MUX_MODE1) /* mcspi4_cs0 */
>;
};
@@ -334,8 +324,6 @@
regulator-name = "smps10_out1";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
- regulator-always-on;
- regulator-boot-on;
};
ldo1_reg: ldo1 {
@@ -503,3 +491,7 @@
pinctrl-names = "default";
pinctrl-0 = <&uart5_pins>;
};
+
+&cpu0 {
+ cpu0-supply = <&smps123_reg>;
+};
diff --git a/arch/arm/boot/dts/omap5.dtsi b/arch/arm/boot/dts/omap5.dtsi
index 6192c45..154d92f 100644
--- a/arch/arm/boot/dts/omap5.dtsi
+++ b/arch/arm/boot/dts/omap5.dtsi
@@ -21,6 +21,11 @@
interrupt-parent = <&gic>;
aliases {
+ i2c0 = &i2c1;
+ i2c1 = &i2c2;
+ i2c2 = &i2c3;
+ i2c3 = &i2c4;
+ i2c4 = &i2c5;
serial0 = &uart1;
serial1 = &uart2;
serial2 = &uart3;
@@ -33,10 +38,17 @@
#address-cells = <1>;
#size-cells = <0>;
- cpu@0 {
+ cpu0: cpu@0 {
device_type = "cpu";
compatible = "arm,cortex-a15";
reg = <0x0>;
+
+ operating-points = <
+ /* kHz uV */
+ 500000 880000
+ 1000000 1060000
+ 1500000 1250000
+ >;
};
cpu@1 {
device_type = "cpu";
@@ -52,7 +64,6 @@
<GIC_PPI 14 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_LOW)>,
<GIC_PPI 11 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_LOW)>,
<GIC_PPI 10 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_LOW)>;
- clock-frequency = <6144000>;
};
gic: interrupt-controller@48211000 {
@@ -607,6 +618,7 @@
emif1: emif@4c000000 {
compatible = "ti,emif-4d5";
ti,hwmods = "emif1";
+ ti,no-idle-on-init;
phy-type = <2>; /* DDR PHY type: Intelli PHY */
reg = <0x4c000000 0x400>;
interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
@@ -618,6 +630,7 @@
emif2: emif@4d000000 {
compatible = "ti,emif-4d5";
ti,hwmods = "emif2";
+ ti,no-idle-on-init;
phy-type = <2>; /* DDR PHY type: Intelli PHY */
reg = <0x4d000000 0x400>;
interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
@@ -648,6 +661,7 @@
reg = <0x4a030000 0x10000>;
interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>;
usb-phy = <&usb2_phy>, <&usb3_phy>;
+ dr_mode = "peripheral";
tx-fifo-resize;
};
};
diff --git a/arch/arm/boot/dts/twl4030.dtsi b/arch/arm/boot/dts/twl4030.dtsi
index ae6a17a..af7fa40 100644
--- a/arch/arm/boot/dts/twl4030.dtsi
+++ b/arch/arm/boot/dts/twl4030.dtsi
@@ -23,6 +23,22 @@
compatible = "ti,twl4030-wdt";
};
+ vaux1: regulator-vaux1 {
+ compatible = "ti,twl4030-vaux1";
+ };
+
+ vaux2: regulator-vaux2 {
+ compatible = "ti,twl4030-vaux2";
+ };
+
+ vaux3: regulator-vaux3 {
+ compatible = "ti,twl4030-vaux3";
+ };
+
+ vaux4: regulator-vaux4 {
+ compatible = "ti,twl4030-vaux4";
+ };
+
vcc: regulator-vdd1 {
compatible = "ti,twl4030-vdd1";
regulator-min-microvolt = <600000>;
@@ -35,10 +51,20 @@
regulator-max-microvolt = <1800000>;
};
- vpll2: regulator-vpll2 {
- compatible = "ti,twl4030-vpll2";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
+ vio: regulator-vio {
+ compatible = "ti,twl4030-vio";
+ };
+
+ vintana1: regulator-vintana1 {
+ compatible = "ti,twl4030-vintana1";
+ };
+
+ vintana2: regulator-vintana2 {
+ compatible = "ti,twl4030-vintana2";
+ };
+
+ vintdig: regulator-vintdig {
+ compatible = "ti,twl4030-vintdig";
};
vmmc1: regulator-vmmc1 {
@@ -65,6 +91,16 @@
compatible = "ti,twl4030-vusb3v1";
};
+ vpll1: regulator-vpll1 {
+ compatible = "ti,twl4030-vpll1";
+ };
+
+ vpll2: regulator-vpll2 {
+ compatible = "ti,twl4030-vpll2";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
vsim: regulator-vsim {
compatible = "ti,twl4030-vsim";
regulator-min-microvolt = <1800000>;
@@ -97,4 +133,9 @@
compatible = "ti,twl4030-pwmled";
#pwm-cells = <2>;
};
+
+ twl_pwrbutton: pwrbutton {
+ compatible = "ti,twl4030-pwrbutton";
+ interrupts = <8>;
+ };
};
diff --git a/include/dt-bindings/pinctrl/am43xx.h b/include/dt-bindings/pinctrl/am43xx.h
new file mode 100644
index 0000000..eb6c366a
--- /dev/null
+++ b/include/dt-bindings/pinctrl/am43xx.h
@@ -0,0 +1,31 @@
+/*
+ * This header provides constants specific to AM43XX pinctrl bindings.
+ */
+
+#ifndef _DT_BINDINGS_PINCTRL_AM43XX_H
+#define _DT_BINDINGS_PINCTRL_AM43XX_H
+
+#define MUX_MODE0 0
+#define MUX_MODE1 1
+#define MUX_MODE2 2
+#define MUX_MODE3 3
+#define MUX_MODE4 4
+#define MUX_MODE5 5
+#define MUX_MODE6 6
+#define MUX_MODE7 7
+
+#define PULL_DISABLE (1 << 16)
+#define PULL_UP (1 << 17)
+#define INPUT_EN (1 << 18)
+#define SLEWCTRL_FAST (1 << 19)
+#define DS0_PULL_UP_DOWN_EN (1 << 27)
+
+#define PIN_OUTPUT (PULL_DISABLE)
+#define PIN_OUTPUT_PULLUP (PULL_UP)
+#define PIN_OUTPUT_PULLDOWN 0
+#define PIN_INPUT (INPUT_EN | PULL_DISABLE)
+#define PIN_INPUT_PULLUP (INPUT_EN | PULL_UP)
+#define PIN_INPUT_PULLDOWN (INPUT_EN)
+
+#endif
+