| /* |
| * Driver for the Renesas RCar I2C unit |
| * |
| * Copyright (C) 2014 Wolfram Sang <wsa@sang-engineering.com> |
| * |
| * Copyright (C) 2012-14 Renesas Solutions Corp. |
| * Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> |
| * |
| * This file is based on the drivers/i2c/busses/i2c-sh7760.c |
| * (c) 2005-2008 MSC Vertriebsges.m.b.H, Manuel Lauss <mlau@msc-ge.com> |
| * |
| * This file used out-of-tree driver i2c-rcar.c |
| * Copyright (C) 2011-2012 Renesas Electronics Corporation |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License as published by |
| * the Free Software Foundation; version 2 of the License. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| */ |
| #include <linux/clk.h> |
| #include <linux/delay.h> |
| #include <linux/err.h> |
| #include <linux/interrupt.h> |
| #include <linux/io.h> |
| #include <linux/i2c.h> |
| #include <linux/i2c/i2c-rcar.h> |
| #include <linux/kernel.h> |
| #include <linux/module.h> |
| #include <linux/of_device.h> |
| #include <linux/platform_device.h> |
| #include <linux/pm_runtime.h> |
| #include <linux/slab.h> |
| #include <linux/spinlock.h> |
| |
| /* register offsets */ |
| #define ICSCR 0x00 /* slave ctrl */ |
| #define ICMCR 0x04 /* master ctrl */ |
| #define ICSSR 0x08 /* slave status */ |
| #define ICMSR 0x0C /* master status */ |
| #define ICSIER 0x10 /* slave irq enable */ |
| #define ICMIER 0x14 /* master irq enable */ |
| #define ICCCR 0x18 /* clock dividers */ |
| #define ICSAR 0x1C /* slave address */ |
| #define ICMAR 0x20 /* master address */ |
| #define ICRXTX 0x24 /* data port */ |
| |
| /* ICMCR */ |
| #define MDBS (1 << 7) /* non-fifo mode switch */ |
| #define FSCL (1 << 6) /* override SCL pin */ |
| #define FSDA (1 << 5) /* override SDA pin */ |
| #define OBPC (1 << 4) /* override pins */ |
| #define MIE (1 << 3) /* master if enable */ |
| #define TSBE (1 << 2) |
| #define FSB (1 << 1) /* force stop bit */ |
| #define ESG (1 << 0) /* en startbit gen */ |
| |
| /* ICMSR (also for ICMIE) */ |
| #define MNR (1 << 6) /* nack received */ |
| #define MAL (1 << 5) /* arbitration lost */ |
| #define MST (1 << 4) /* sent a stop */ |
| #define MDE (1 << 3) |
| #define MDT (1 << 2) |
| #define MDR (1 << 1) |
| #define MAT (1 << 0) /* slave addr xfer done */ |
| |
| |
| #define RCAR_BUS_PHASE_START (MDBS | MIE | ESG) |
| #define RCAR_BUS_PHASE_DATA (MDBS | MIE) |
| #define RCAR_BUS_PHASE_STOP (MDBS | MIE | FSB) |
| |
| #define RCAR_IRQ_SEND (MNR | MAL | MST | MAT | MDE) |
| #define RCAR_IRQ_RECV (MNR | MAL | MST | MAT | MDR) |
| #define RCAR_IRQ_STOP (MST) |
| |
| #define RCAR_IRQ_ACK_SEND (~(MAT | MDE) & 0xFF) |
| #define RCAR_IRQ_ACK_RECV (~(MAT | MDR) & 0xFF) |
| |
| #define ID_LAST_MSG (1 << 0) |
| #define ID_IOERROR (1 << 1) |
| #define ID_DONE (1 << 2) |
| #define ID_ARBLOST (1 << 3) |
| #define ID_NACK (1 << 4) |
| |
| enum rcar_i2c_type { |
| I2C_RCAR_GEN1, |
| I2C_RCAR_GEN2, |
| }; |
| |
| struct rcar_i2c_priv { |
| void __iomem *io; |
| struct i2c_adapter adap; |
| struct i2c_msg *msg; |
| struct clk *clk; |
| |
| spinlock_t lock; |
| wait_queue_head_t wait; |
| |
| int pos; |
| u32 icccr; |
| u32 flags; |
| enum rcar_i2c_type devtype; |
| }; |
| |
| #define rcar_i2c_priv_to_dev(p) ((p)->adap.dev.parent) |
| #define rcar_i2c_is_recv(p) ((p)->msg->flags & I2C_M_RD) |
| |
| #define rcar_i2c_flags_set(p, f) ((p)->flags |= (f)) |
| #define rcar_i2c_flags_has(p, f) ((p)->flags & (f)) |
| |
| #define LOOP_TIMEOUT 1024 |
| |
| |
| static void rcar_i2c_write(struct rcar_i2c_priv *priv, int reg, u32 val) |
| { |
| writel(val, priv->io + reg); |
| } |
| |
| static u32 rcar_i2c_read(struct rcar_i2c_priv *priv, int reg) |
| { |
| return readl(priv->io + reg); |
| } |
| |
| static void rcar_i2c_init(struct rcar_i2c_priv *priv) |
| { |
| /* |
| * reset slave mode. |
| * slave mode is not used on this driver |
| */ |
| rcar_i2c_write(priv, ICSIER, 0); |
| rcar_i2c_write(priv, ICSAR, 0); |
| rcar_i2c_write(priv, ICSCR, 0); |
| rcar_i2c_write(priv, ICSSR, 0); |
| |
| /* reset master mode */ |
| rcar_i2c_write(priv, ICMIER, 0); |
| rcar_i2c_write(priv, ICMCR, 0); |
| rcar_i2c_write(priv, ICMSR, 0); |
| rcar_i2c_write(priv, ICMAR, 0); |
| } |
| |
| static int rcar_i2c_bus_barrier(struct rcar_i2c_priv *priv) |
| { |
| int i; |
| |
| for (i = 0; i < LOOP_TIMEOUT; i++) { |
| /* make sure that bus is not busy */ |
| if (!(rcar_i2c_read(priv, ICMCR) & FSDA)) |
| return 0; |
| udelay(1); |
| } |
| |
| return -EBUSY; |
| } |
| |
| static int rcar_i2c_clock_calculate(struct rcar_i2c_priv *priv, |
| u32 bus_speed, |
| struct device *dev) |
| { |
| u32 scgd, cdf; |
| u32 round, ick; |
| u32 scl; |
| u32 cdf_width; |
| unsigned long rate; |
| |
| switch (priv->devtype) { |
| case I2C_RCAR_GEN1: |
| cdf_width = 2; |
| break; |
| case I2C_RCAR_GEN2: |
| cdf_width = 3; |
| break; |
| default: |
| dev_err(dev, "device type error\n"); |
| return -EIO; |
| } |
| |
| /* |
| * calculate SCL clock |
| * see |
| * ICCCR |
| * |
| * ick = clkp / (1 + CDF) |
| * SCL = ick / (20 + SCGD * 8 + F[(ticf + tr + intd) * ick]) |
| * |
| * ick : I2C internal clock < 20 MHz |
| * ticf : I2C SCL falling time = 35 ns here |
| * tr : I2C SCL rising time = 200 ns here |
| * intd : LSI internal delay = 50 ns here |
| * clkp : peripheral_clk |
| * F[] : integer up-valuation |
| */ |
| rate = clk_get_rate(priv->clk); |
| cdf = rate / 20000000; |
| if (cdf >= 1U << cdf_width) { |
| dev_err(dev, "Input clock %lu too high\n", rate); |
| return -EIO; |
| } |
| ick = rate / (cdf + 1); |
| |
| /* |
| * it is impossible to calculate large scale |
| * number on u32. separate it |
| * |
| * F[(ticf + tr + intd) * ick] |
| * = F[(35 + 200 + 50)ns * ick] |
| * = F[285 * ick / 1000000000] |
| * = F[(ick / 1000000) * 285 / 1000] |
| */ |
| round = (ick + 500000) / 1000000 * 285; |
| round = (round + 500) / 1000; |
| |
| /* |
| * SCL = ick / (20 + SCGD * 8 + F[(ticf + tr + intd) * ick]) |
| * |
| * Calculation result (= SCL) should be less than |
| * bus_speed for hardware safety |
| * |
| * We could use something along the lines of |
| * div = ick / (bus_speed + 1) + 1; |
| * scgd = (div - 20 - round + 7) / 8; |
| * scl = ick / (20 + (scgd * 8) + round); |
| * (not fully verified) but that would get pretty involved |
| */ |
| for (scgd = 0; scgd < 0x40; scgd++) { |
| scl = ick / (20 + (scgd * 8) + round); |
| if (scl <= bus_speed) |
| goto scgd_find; |
| } |
| dev_err(dev, "it is impossible to calculate best SCL\n"); |
| return -EIO; |
| |
| scgd_find: |
| dev_dbg(dev, "clk %d/%d(%lu), round %u, CDF:0x%x, SCGD: 0x%x\n", |
| scl, bus_speed, clk_get_rate(priv->clk), round, cdf, scgd); |
| |
| /* |
| * keep icccr value |
| */ |
| priv->icccr = scgd << cdf_width | cdf; |
| |
| return 0; |
| } |
| |
| static void rcar_i2c_prepare_msg(struct rcar_i2c_priv *priv) |
| { |
| int read = !!rcar_i2c_is_recv(priv); |
| |
| rcar_i2c_write(priv, ICMAR, (priv->msg->addr << 1) | read); |
| rcar_i2c_write(priv, ICMSR, 0); |
| rcar_i2c_write(priv, ICMCR, RCAR_BUS_PHASE_START); |
| rcar_i2c_write(priv, ICMIER, read ? RCAR_IRQ_RECV : RCAR_IRQ_SEND); |
| } |
| |
| /* |
| * interrupt functions |
| */ |
| static int rcar_i2c_irq_send(struct rcar_i2c_priv *priv, u32 msr) |
| { |
| struct i2c_msg *msg = priv->msg; |
| |
| /* |
| * FIXME |
| * sometimes, unknown interrupt happened. |
| * Do nothing |
| */ |
| if (!(msr & MDE)) |
| return 0; |
| |
| /* |
| * If address transfer phase finished, |
| * goto data phase. |
| */ |
| if (msr & MAT) |
| rcar_i2c_write(priv, ICMCR, RCAR_BUS_PHASE_DATA); |
| |
| if (priv->pos < msg->len) { |
| /* |
| * Prepare next data to ICRXTX register. |
| * This data will go to _SHIFT_ register. |
| * |
| * * |
| * [ICRXTX] -> [SHIFT] -> [I2C bus] |
| */ |
| rcar_i2c_write(priv, ICRXTX, msg->buf[priv->pos]); |
| priv->pos++; |
| |
| } else { |
| /* |
| * The last data was pushed to ICRXTX on _PREV_ empty irq. |
| * It is on _SHIFT_ register, and will sent to I2C bus. |
| * |
| * * |
| * [ICRXTX] -> [SHIFT] -> [I2C bus] |
| */ |
| |
| if (priv->flags & ID_LAST_MSG) |
| /* |
| * If current msg is the _LAST_ msg, |
| * prepare stop condition here. |
| * ID_DONE will be set on STOP irq. |
| */ |
| rcar_i2c_write(priv, ICMCR, RCAR_BUS_PHASE_STOP); |
| else |
| /* |
| * If current msg is _NOT_ last msg, |
| * it doesn't call stop phase. |
| * thus, there is no STOP irq. |
| * return ID_DONE here. |
| */ |
| return ID_DONE; |
| } |
| |
| rcar_i2c_write(priv, ICMSR, RCAR_IRQ_ACK_SEND); |
| |
| return 0; |
| } |
| |
| static int rcar_i2c_irq_recv(struct rcar_i2c_priv *priv, u32 msr) |
| { |
| struct i2c_msg *msg = priv->msg; |
| |
| /* |
| * FIXME |
| * sometimes, unknown interrupt happened. |
| * Do nothing |
| */ |
| if (!(msr & MDR)) |
| return 0; |
| |
| if (msr & MAT) { |
| /* |
| * Address transfer phase finished, |
| * but, there is no data at this point. |
| * Do nothing. |
| */ |
| } else if (priv->pos < msg->len) { |
| /* |
| * get received data |
| */ |
| msg->buf[priv->pos] = rcar_i2c_read(priv, ICRXTX); |
| priv->pos++; |
| } |
| |
| /* |
| * If next received data is the _LAST_, |
| * go to STOP phase, |
| * otherwise, go to DATA phase. |
| */ |
| if (priv->pos + 1 >= msg->len) |
| rcar_i2c_write(priv, ICMCR, RCAR_BUS_PHASE_STOP); |
| else |
| rcar_i2c_write(priv, ICMCR, RCAR_BUS_PHASE_DATA); |
| |
| rcar_i2c_write(priv, ICMSR, RCAR_IRQ_ACK_RECV); |
| |
| return 0; |
| } |
| |
| static irqreturn_t rcar_i2c_irq(int irq, void *ptr) |
| { |
| struct rcar_i2c_priv *priv = ptr; |
| irqreturn_t result = IRQ_HANDLED; |
| u32 msr; |
| |
| /*-------------- spin lock -----------------*/ |
| spin_lock(&priv->lock); |
| |
| msr = rcar_i2c_read(priv, ICMSR); |
| |
| /* Only handle interrupts that are currently enabled */ |
| msr &= rcar_i2c_read(priv, ICMIER); |
| if (!msr) { |
| result = IRQ_NONE; |
| goto exit; |
| } |
| |
| /* Arbitration lost */ |
| if (msr & MAL) { |
| rcar_i2c_flags_set(priv, (ID_DONE | ID_ARBLOST)); |
| goto out; |
| } |
| |
| /* Nack */ |
| if (msr & MNR) { |
| /* go to stop phase */ |
| rcar_i2c_write(priv, ICMCR, RCAR_BUS_PHASE_STOP); |
| rcar_i2c_write(priv, ICMIER, RCAR_IRQ_STOP); |
| rcar_i2c_flags_set(priv, ID_NACK); |
| goto out; |
| } |
| |
| /* Stop */ |
| if (msr & MST) { |
| rcar_i2c_flags_set(priv, ID_DONE); |
| goto out; |
| } |
| |
| if (rcar_i2c_is_recv(priv)) |
| rcar_i2c_flags_set(priv, rcar_i2c_irq_recv(priv, msr)); |
| else |
| rcar_i2c_flags_set(priv, rcar_i2c_irq_send(priv, msr)); |
| |
| out: |
| if (rcar_i2c_flags_has(priv, ID_DONE)) { |
| rcar_i2c_write(priv, ICMIER, 0); |
| rcar_i2c_write(priv, ICMSR, 0); |
| wake_up(&priv->wait); |
| } |
| |
| exit: |
| spin_unlock(&priv->lock); |
| /*-------------- spin unlock -----------------*/ |
| |
| return result; |
| } |
| |
| static int rcar_i2c_master_xfer(struct i2c_adapter *adap, |
| struct i2c_msg *msgs, |
| int num) |
| { |
| struct rcar_i2c_priv *priv = i2c_get_adapdata(adap); |
| struct device *dev = rcar_i2c_priv_to_dev(priv); |
| unsigned long flags; |
| int i, ret, timeout; |
| |
| pm_runtime_get_sync(dev); |
| |
| /*-------------- spin lock -----------------*/ |
| spin_lock_irqsave(&priv->lock, flags); |
| |
| rcar_i2c_init(priv); |
| /* start clock */ |
| rcar_i2c_write(priv, ICCCR, priv->icccr); |
| |
| spin_unlock_irqrestore(&priv->lock, flags); |
| /*-------------- spin unlock -----------------*/ |
| |
| ret = rcar_i2c_bus_barrier(priv); |
| if (ret < 0) |
| goto out; |
| |
| for (i = 0; i < num; i++) { |
| /* This HW can't send STOP after address phase */ |
| if (msgs[i].len == 0) { |
| ret = -EOPNOTSUPP; |
| break; |
| } |
| |
| /*-------------- spin lock -----------------*/ |
| spin_lock_irqsave(&priv->lock, flags); |
| |
| /* init each data */ |
| priv->msg = &msgs[i]; |
| priv->pos = 0; |
| priv->flags = 0; |
| if (i == num - 1) |
| rcar_i2c_flags_set(priv, ID_LAST_MSG); |
| |
| rcar_i2c_prepare_msg(priv); |
| |
| spin_unlock_irqrestore(&priv->lock, flags); |
| /*-------------- spin unlock -----------------*/ |
| |
| timeout = wait_event_timeout(priv->wait, |
| rcar_i2c_flags_has(priv, ID_DONE), |
| 5 * HZ); |
| if (!timeout) { |
| ret = -ETIMEDOUT; |
| break; |
| } |
| |
| if (rcar_i2c_flags_has(priv, ID_NACK)) { |
| ret = -ENXIO; |
| break; |
| } |
| |
| if (rcar_i2c_flags_has(priv, ID_ARBLOST)) { |
| ret = -EAGAIN; |
| break; |
| } |
| |
| if (rcar_i2c_flags_has(priv, ID_IOERROR)) { |
| ret = -EIO; |
| break; |
| } |
| |
| ret = i + 1; /* The number of transfer */ |
| } |
| out: |
| pm_runtime_put(dev); |
| |
| if (ret < 0 && ret != -ENXIO) |
| dev_err(dev, "error %d : %x\n", ret, priv->flags); |
| |
| return ret; |
| } |
| |
| static u32 rcar_i2c_func(struct i2c_adapter *adap) |
| { |
| /* This HW can't do SMBUS_QUICK and NOSTART */ |
| return I2C_FUNC_I2C | (I2C_FUNC_SMBUS_EMUL & ~I2C_FUNC_SMBUS_QUICK); |
| } |
| |
| static const struct i2c_algorithm rcar_i2c_algo = { |
| .master_xfer = rcar_i2c_master_xfer, |
| .functionality = rcar_i2c_func, |
| }; |
| |
| static const struct of_device_id rcar_i2c_dt_ids[] = { |
| { .compatible = "renesas,i2c-rcar", .data = (void *)I2C_RCAR_GEN1 }, |
| { .compatible = "renesas,i2c-r8a7778", .data = (void *)I2C_RCAR_GEN1 }, |
| { .compatible = "renesas,i2c-r8a7779", .data = (void *)I2C_RCAR_GEN1 }, |
| { .compatible = "renesas,i2c-r8a7790", .data = (void *)I2C_RCAR_GEN2 }, |
| { .compatible = "renesas,i2c-r8a7791", .data = (void *)I2C_RCAR_GEN2 }, |
| { .compatible = "renesas,i2c-r8a7792", .data = (void *)I2C_RCAR_GEN2 }, |
| { .compatible = "renesas,i2c-r8a7793", .data = (void *)I2C_RCAR_GEN2 }, |
| { .compatible = "renesas,i2c-r8a7794", .data = (void *)I2C_RCAR_GEN2 }, |
| {}, |
| }; |
| MODULE_DEVICE_TABLE(of, rcar_i2c_dt_ids); |
| |
| static int rcar_i2c_probe(struct platform_device *pdev) |
| { |
| struct i2c_rcar_platform_data *pdata = dev_get_platdata(&pdev->dev); |
| struct rcar_i2c_priv *priv; |
| struct i2c_adapter *adap; |
| struct resource *res; |
| struct device *dev = &pdev->dev; |
| u32 bus_speed; |
| int irq, ret; |
| |
| priv = devm_kzalloc(dev, sizeof(struct rcar_i2c_priv), GFP_KERNEL); |
| if (!priv) |
| return -ENOMEM; |
| |
| priv->clk = devm_clk_get(dev, NULL); |
| if (IS_ERR(priv->clk)) { |
| dev_err(dev, "cannot get clock\n"); |
| return PTR_ERR(priv->clk); |
| } |
| |
| bus_speed = 100000; /* default 100 kHz */ |
| ret = of_property_read_u32(dev->of_node, "clock-frequency", &bus_speed); |
| if (ret < 0 && pdata && pdata->bus_speed) |
| bus_speed = pdata->bus_speed; |
| |
| if (pdev->dev.of_node) |
| priv->devtype = (long)of_match_device(rcar_i2c_dt_ids, |
| dev)->data; |
| else |
| priv->devtype = platform_get_device_id(pdev)->driver_data; |
| |
| ret = rcar_i2c_clock_calculate(priv, bus_speed, dev); |
| if (ret < 0) |
| return ret; |
| |
| res = platform_get_resource(pdev, IORESOURCE_MEM, 0); |
| priv->io = devm_ioremap_resource(dev, res); |
| if (IS_ERR(priv->io)) |
| return PTR_ERR(priv->io); |
| |
| irq = platform_get_irq(pdev, 0); |
| init_waitqueue_head(&priv->wait); |
| spin_lock_init(&priv->lock); |
| |
| adap = &priv->adap; |
| adap->nr = pdev->id; |
| adap->algo = &rcar_i2c_algo; |
| adap->class = I2C_CLASS_DEPRECATED; |
| adap->retries = 3; |
| adap->dev.parent = dev; |
| adap->dev.of_node = dev->of_node; |
| i2c_set_adapdata(adap, priv); |
| strlcpy(adap->name, pdev->name, sizeof(adap->name)); |
| |
| ret = devm_request_irq(dev, irq, rcar_i2c_irq, 0, |
| dev_name(dev), priv); |
| if (ret < 0) { |
| dev_err(dev, "cannot get irq %d\n", irq); |
| return ret; |
| } |
| |
| ret = i2c_add_numbered_adapter(adap); |
| if (ret < 0) { |
| dev_err(dev, "reg adap failed: %d\n", ret); |
| return ret; |
| } |
| |
| pm_runtime_enable(dev); |
| platform_set_drvdata(pdev, priv); |
| |
| dev_info(dev, "probed\n"); |
| |
| return 0; |
| } |
| |
| static int rcar_i2c_remove(struct platform_device *pdev) |
| { |
| struct rcar_i2c_priv *priv = platform_get_drvdata(pdev); |
| struct device *dev = &pdev->dev; |
| |
| i2c_del_adapter(&priv->adap); |
| pm_runtime_disable(dev); |
| |
| return 0; |
| } |
| |
| static struct platform_device_id rcar_i2c_id_table[] = { |
| { "i2c-rcar", I2C_RCAR_GEN1 }, |
| { "i2c-rcar_gen1", I2C_RCAR_GEN1 }, |
| { "i2c-rcar_gen2", I2C_RCAR_GEN2 }, |
| {}, |
| }; |
| MODULE_DEVICE_TABLE(platform, rcar_i2c_id_table); |
| |
| static struct platform_driver rcar_i2c_driver = { |
| .driver = { |
| .name = "i2c-rcar", |
| .owner = THIS_MODULE, |
| .of_match_table = rcar_i2c_dt_ids, |
| }, |
| .probe = rcar_i2c_probe, |
| .remove = rcar_i2c_remove, |
| .id_table = rcar_i2c_id_table, |
| }; |
| |
| module_platform_driver(rcar_i2c_driver); |
| |
| MODULE_LICENSE("GPL v2"); |
| MODULE_DESCRIPTION("Renesas R-Car I2C bus driver"); |
| MODULE_AUTHOR("Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>"); |