ath10k: make warm reset a bit safer and faster
One of the problems with warm reset I've found is
that it must be guaranteed that copy engine
registers are not being accessed while being
reset. Otherwise in worst case scenario the host
may lock up.
Instead of using sleeps and hoping the device is
operational in some arbitrary timeframes use
firmware indication register.
As a side effect this makes driver
boot/stop/recovery faster.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
diff --git a/drivers/net/wireless/ath/ath10k/pci.c b/drivers/net/wireless/ath/ath10k/pci.c
index a8a3e1b..af36730 100644
--- a/drivers/net/wireless/ath/ath10k/pci.c
+++ b/drivers/net/wireless/ath/ath10k/pci.c
@@ -1717,89 +1717,75 @@
msleep(10);
}
-static int ath10k_pci_warm_reset(struct ath10k *ar)
+static void ath10k_pci_warm_reset_cpu(struct ath10k *ar)
{
u32 val;
- ath10k_dbg(ar, ATH10K_DBG_BOOT, "boot warm reset\n");
-
- spin_lock_bh(&ar->data_lock);
-
- ar->stats.fw_warm_reset_counter++;
-
- spin_unlock_bh(&ar->data_lock);
-
- /* debug */
- val = ath10k_pci_read32(ar, SOC_CORE_BASE_ADDRESS +
- PCIE_INTR_CAUSE_ADDRESS);
- ath10k_dbg(ar, ATH10K_DBG_BOOT, "boot host cpu intr cause: 0x%08x\n",
- val);
-
- val = ath10k_pci_read32(ar, SOC_CORE_BASE_ADDRESS +
- CPU_INTR_ADDRESS);
- ath10k_dbg(ar, ATH10K_DBG_BOOT, "boot target cpu intr cause: 0x%08x\n",
- val);
-
- /* disable pending irqs */
- ath10k_pci_write32(ar, SOC_CORE_BASE_ADDRESS +
- PCIE_INTR_ENABLE_ADDRESS, 0);
-
- ath10k_pci_write32(ar, SOC_CORE_BASE_ADDRESS +
- PCIE_INTR_CLR_ADDRESS, ~0);
-
- msleep(100);
-
- /* clear fw indicator */
ath10k_pci_write32(ar, FW_INDICATOR_ADDRESS, 0);
- /* clear target LF timer interrupts */
+ val = ath10k_pci_read32(ar, RTC_SOC_BASE_ADDRESS +
+ SOC_RESET_CONTROL_ADDRESS);
+ ath10k_pci_write32(ar, RTC_SOC_BASE_ADDRESS + SOC_RESET_CONTROL_ADDRESS,
+ val | SOC_RESET_CONTROL_CPU_WARM_RST_MASK);
+}
+
+static void ath10k_pci_warm_reset_ce(struct ath10k *ar)
+{
+ u32 val;
+
+ val = ath10k_pci_read32(ar, RTC_SOC_BASE_ADDRESS +
+ SOC_RESET_CONTROL_ADDRESS);
+
+ ath10k_pci_write32(ar, RTC_SOC_BASE_ADDRESS + SOC_RESET_CONTROL_ADDRESS,
+ val | SOC_RESET_CONTROL_CE_RST_MASK);
+ msleep(10);
+ ath10k_pci_write32(ar, RTC_SOC_BASE_ADDRESS + SOC_RESET_CONTROL_ADDRESS,
+ val & ~SOC_RESET_CONTROL_CE_RST_MASK);
+}
+
+static void ath10k_pci_warm_reset_clear_lf(struct ath10k *ar)
+{
+ u32 val;
+
val = ath10k_pci_read32(ar, RTC_SOC_BASE_ADDRESS +
SOC_LF_TIMER_CONTROL0_ADDRESS);
ath10k_pci_write32(ar, RTC_SOC_BASE_ADDRESS +
SOC_LF_TIMER_CONTROL0_ADDRESS,
val & ~SOC_LF_TIMER_CONTROL0_ENABLE_MASK);
+}
- /* reset CE */
- val = ath10k_pci_read32(ar, RTC_SOC_BASE_ADDRESS +
- SOC_RESET_CONTROL_ADDRESS);
- ath10k_pci_write32(ar, RTC_SOC_BASE_ADDRESS + SOC_RESET_CONTROL_ADDRESS,
- val | SOC_RESET_CONTROL_CE_RST_MASK);
- val = ath10k_pci_read32(ar, RTC_SOC_BASE_ADDRESS +
- SOC_RESET_CONTROL_ADDRESS);
- msleep(10);
+static int ath10k_pci_warm_reset(struct ath10k *ar)
+{
+ int ret;
- /* unreset CE */
- ath10k_pci_write32(ar, RTC_SOC_BASE_ADDRESS + SOC_RESET_CONTROL_ADDRESS,
- val & ~SOC_RESET_CONTROL_CE_RST_MASK);
- val = ath10k_pci_read32(ar, RTC_SOC_BASE_ADDRESS +
- SOC_RESET_CONTROL_ADDRESS);
- msleep(10);
+ ath10k_dbg(ar, ATH10K_DBG_BOOT, "boot warm reset\n");
+ spin_lock_bh(&ar->data_lock);
+ ar->stats.fw_warm_reset_counter++;
+ spin_unlock_bh(&ar->data_lock);
+
+ ath10k_pci_irq_disable(ar);
+
+ /* Make sure the target CPU is not doing anything dangerous, e.g. if it
+ * were to access copy engine while host performs copy engine reset
+ * then it is possible for the device to confuse pci-e controller to
+ * the point of bringing host system to a complete stop (i.e. hang).
+ */
ath10k_pci_warm_reset_si0(ar);
+ ath10k_pci_warm_reset_cpu(ar);
+ ath10k_pci_init_pipes(ar);
+ ath10k_pci_wait_for_target_init(ar);
- /* debug */
- val = ath10k_pci_read32(ar, SOC_CORE_BASE_ADDRESS +
- PCIE_INTR_CAUSE_ADDRESS);
- ath10k_dbg(ar, ATH10K_DBG_BOOT, "boot host cpu intr cause: 0x%08x\n",
- val);
+ ath10k_pci_warm_reset_clear_lf(ar);
+ ath10k_pci_warm_reset_ce(ar);
+ ath10k_pci_warm_reset_cpu(ar);
+ ath10k_pci_init_pipes(ar);
- val = ath10k_pci_read32(ar, SOC_CORE_BASE_ADDRESS +
- CPU_INTR_ADDRESS);
- ath10k_dbg(ar, ATH10K_DBG_BOOT, "boot target cpu intr cause: 0x%08x\n",
- val);
-
- /* CPU warm reset */
- val = ath10k_pci_read32(ar, RTC_SOC_BASE_ADDRESS +
- SOC_RESET_CONTROL_ADDRESS);
- ath10k_pci_write32(ar, RTC_SOC_BASE_ADDRESS + SOC_RESET_CONTROL_ADDRESS,
- val | SOC_RESET_CONTROL_CPU_WARM_RST_MASK);
-
- val = ath10k_pci_read32(ar, RTC_SOC_BASE_ADDRESS +
- SOC_RESET_CONTROL_ADDRESS);
- ath10k_dbg(ar, ATH10K_DBG_BOOT, "boot target reset state: 0x%08x\n",
- val);
-
- msleep(100);
+ ret = ath10k_pci_wait_for_target_init(ar);
+ if (ret) {
+ ath10k_warn(ar, "failed to wait for target init: %d\n", ret);
+ return ret;
+ }
ath10k_dbg(ar, ATH10K_DBG_BOOT, "boot warm reset complete\n");