[PATCH] 3c59x: convert to use of pci_iomap API
Convert 3c59x driver to use pci_iomap API. This makes it easier to enable
the use of memory-mapped PCI I/O resources.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
diff --git a/drivers/net/3c59x.c b/drivers/net/3c59x.c
index 455ba91..2bad41b 100644
--- a/drivers/net/3c59x.c
+++ b/drivers/net/3c59x.c
@@ -602,7 +602,7 @@
First the windows. There are eight register windows, with the command
and status registers available in each.
*/
-#define EL3WINDOW(win_num) outw(SelectWindow + (win_num), ioaddr + EL3_CMD)
+#define EL3WINDOW(win_num) iowrite16(SelectWindow + (win_num), ioaddr + EL3_CMD)
#define EL3_CMD 0x0e
#define EL3_STATUS 0x0e
@@ -776,7 +776,8 @@
/* PCI configuration space information. */
struct device *gendev;
- char __iomem *cb_fn_base; /* CardBus function status addr space. */
+ void __iomem *ioaddr; /* IO address space */
+ void __iomem *cb_fn_base; /* CardBus function status addr space. */
/* Some values here only for performance evaluation and path-coverage */
int rx_nocopy, rx_copy, queued_packet, rx_csumhits;
@@ -869,12 +870,12 @@
/* number of ETHTOOL_GSTATS u64's */
#define VORTEX_NUM_STATS 3
-static int vortex_probe1(struct device *gendev, long ioaddr, int irq,
+static int vortex_probe1(struct device *gendev, void __iomem *ioaddr, int irq,
int chip_idx, int card_idx);
static void vortex_up(struct net_device *dev);
static void vortex_down(struct net_device *dev, int final);
static int vortex_open(struct net_device *dev);
-static void mdio_sync(long ioaddr, int bits);
+static void mdio_sync(void __iomem *ioaddr, int bits);
static int mdio_read(struct net_device *dev, int phy_id, int location);
static void mdio_write(struct net_device *vp, int phy_id, int location, int value);
static void vortex_timer(unsigned long arg);
@@ -887,7 +888,7 @@
static irqreturn_t boomerang_interrupt(int irq, void *dev_id, struct pt_regs *regs);
static int vortex_close(struct net_device *dev);
static void dump_tx_ring(struct net_device *dev);
-static void update_stats(long ioaddr, struct net_device *dev);
+static void update_stats(void __iomem *ioaddr, struct net_device *dev);
static struct net_device_stats *vortex_get_stats(struct net_device *dev);
static void set_rx_mode(struct net_device *dev);
#ifdef CONFIG_PCI
@@ -1029,18 +1030,19 @@
static int vortex_eisa_probe (struct device *device)
{
- long ioaddr;
+ void __iomem *ioaddr;
struct eisa_device *edev;
edev = to_eisa_device (device);
- ioaddr = edev->base_addr;
- if (!request_region(ioaddr, VORTEX_TOTAL_SIZE, DRV_NAME))
+ if (!request_region(edev->base_addr, VORTEX_TOTAL_SIZE, DRV_NAME))
return -EBUSY;
- if (vortex_probe1(device, ioaddr, inw(ioaddr + 0xC88) >> 12,
+ ioaddr = ioport_map(edev->base_addr, VORTEX_TOTAL_SIZE);
+
+ if (vortex_probe1(device, ioaddr, ioread16(ioaddr + 0xC88) >> 12,
edev->id.driver_data, vortex_cards_found)) {
- release_region (ioaddr, VORTEX_TOTAL_SIZE);
+ release_region (edev->base_addr, VORTEX_TOTAL_SIZE);
return -ENODEV;
}
@@ -1054,7 +1056,7 @@
struct eisa_device *edev;
struct net_device *dev;
struct vortex_private *vp;
- long ioaddr;
+ void __iomem *ioaddr;
edev = to_eisa_device (device);
dev = eisa_get_drvdata (edev);
@@ -1065,11 +1067,11 @@
}
vp = netdev_priv(dev);
- ioaddr = dev->base_addr;
+ ioaddr = vp->ioaddr;
unregister_netdev (dev);
- outw (TotalReset|0x14, ioaddr + EL3_CMD);
- release_region (ioaddr, VORTEX_TOTAL_SIZE);
+ iowrite16 (TotalReset|0x14, ioaddr + EL3_CMD);
+ release_region (dev->base_addr, VORTEX_TOTAL_SIZE);
free_netdev (dev);
return 0;
@@ -1096,8 +1098,8 @@
/* Special code to work-around the Compaq PCI BIOS32 problem. */
if (compaq_ioaddr) {
- vortex_probe1(NULL, compaq_ioaddr, compaq_irq,
- compaq_device_id, vortex_cards_found++);
+ vortex_probe1(NULL, ioport_map(compaq_ioaddr, VORTEX_TOTAL_SIZE),
+ compaq_irq, compaq_device_id, vortex_cards_found++);
}
return vortex_cards_found - orig_cards_found + eisa_found;
@@ -1114,8 +1116,8 @@
if (rc < 0)
goto out;
- rc = vortex_probe1 (&pdev->dev, pci_resource_start (pdev, 0),
- pdev->irq, ent->driver_data, vortex_cards_found);
+ rc = vortex_probe1 (&pdev->dev, pci_iomap(pdev, 0, 0),
+ pdev->irq, ent->driver_data, vortex_cards_found);
if (rc < 0) {
pci_disable_device (pdev);
goto out;
@@ -1134,7 +1136,7 @@
* NOTE: pdev can be NULL, for the case of a Compaq device
*/
static int __devinit vortex_probe1(struct device *gendev,
- long ioaddr, int irq,
+ void __iomem *ioaddr, int irq,
int chip_idx, int card_idx)
{
struct vortex_private *vp;
@@ -1202,15 +1204,16 @@
if (print_info)
printk (KERN_INFO "See Documentation/networking/vortex.txt\n");
- printk(KERN_INFO "%s: 3Com %s %s at 0x%lx. Vers " DRV_VERSION "\n",
+ printk(KERN_INFO "%s: 3Com %s %s at %p. Vers " DRV_VERSION "\n",
print_name,
pdev ? "PCI" : "EISA",
vci->name,
ioaddr);
- dev->base_addr = ioaddr;
+ dev->base_addr = (unsigned long)ioaddr;
dev->irq = irq;
dev->mtu = mtu;
+ vp->ioaddr = ioaddr;
vp->large_frames = mtu > 1500;
vp->drv_flags = vci->drv_flags;
vp->has_nway = (vci->drv_flags & HAS_NWAY) ? 1 : 0;
@@ -1226,7 +1229,7 @@
if (pdev) {
/* EISA resources already marked, so only PCI needs to do this here */
/* Ignore return value, because Cardbus drivers already allocate for us */
- if (request_region(ioaddr, vci->io_size, print_name) != NULL)
+ if (request_region(dev->base_addr, vci->io_size, print_name) != NULL)
vp->must_free_region = 1;
/* enable bus-mastering if necessary */
@@ -1316,14 +1319,14 @@
for (i = 0; i < 0x40; i++) {
int timer;
- outw(base + i, ioaddr + Wn0EepromCmd);
+ iowrite16(base + i, ioaddr + Wn0EepromCmd);
/* Pause for at least 162 us. for the read to take place. */
for (timer = 10; timer >= 0; timer--) {
udelay(162);
- if ((inw(ioaddr + Wn0EepromCmd) & 0x8000) == 0)
+ if ((ioread16(ioaddr + Wn0EepromCmd) & 0x8000) == 0)
break;
}
- eeprom[i] = inw(ioaddr + Wn0EepromData);
+ eeprom[i] = ioread16(ioaddr + Wn0EepromData);
}
}
for (i = 0; i < 0x18; i++)
@@ -1351,7 +1354,7 @@
}
EL3WINDOW(2);
for (i = 0; i < 6; i++)
- outb(dev->dev_addr[i], ioaddr + i);
+ iowrite8(dev->dev_addr[i], ioaddr + i);
#ifdef __sparc__
if (print_info)
@@ -1366,7 +1369,7 @@
#endif
EL3WINDOW(4);
- step = (inb(ioaddr + Wn4_NetDiag) & 0x1e) >> 1;
+ step = (ioread8(ioaddr + Wn4_NetDiag) & 0x1e) >> 1;
if (print_info) {
printk(KERN_INFO " product code %02x%02x rev %02x.%d date %02d-"
"%02d-%02d\n", eeprom[6]&0xff, eeprom[6]>>8, eeprom[0x14],
@@ -1375,31 +1378,30 @@
if (pdev && vci->drv_flags & HAS_CB_FNS) {
- unsigned long fn_st_addr; /* Cardbus function status space */
unsigned short n;
- fn_st_addr = pci_resource_start (pdev, 2);
- if (fn_st_addr) {
- vp->cb_fn_base = ioremap(fn_st_addr, 128);
+ vp->cb_fn_base = pci_iomap(pdev, 2, 0);
+ if (!vp->cb_fn_base) {
retval = -ENOMEM;
- if (!vp->cb_fn_base)
- goto free_ring;
+ goto free_ring;
}
+
if (print_info) {
printk(KERN_INFO "%s: CardBus functions mapped %8.8lx->%p\n",
- print_name, fn_st_addr, vp->cb_fn_base);
+ print_name, pci_resource_start(pdev, 2),
+ vp->cb_fn_base);
}
EL3WINDOW(2);
- n = inw(ioaddr + Wn2_ResetOptions) & ~0x4010;
+ n = ioread16(ioaddr + Wn2_ResetOptions) & ~0x4010;
if (vp->drv_flags & INVERT_LED_PWR)
n |= 0x10;
if (vp->drv_flags & INVERT_MII_PWR)
n |= 0x4000;
- outw(n, ioaddr + Wn2_ResetOptions);
+ iowrite16(n, ioaddr + Wn2_ResetOptions);
if (vp->drv_flags & WNO_XCVR_PWR) {
EL3WINDOW(0);
- outw(0x0800, ioaddr);
+ iowrite16(0x0800, ioaddr);
}
}
@@ -1418,13 +1420,13 @@
static const char * ram_split[] = {"5:3", "3:1", "1:1", "3:5"};
unsigned int config;
EL3WINDOW(3);
- vp->available_media = inw(ioaddr + Wn3_Options);
+ vp->available_media = ioread16(ioaddr + Wn3_Options);
if ((vp->available_media & 0xff) == 0) /* Broken 3c916 */
vp->available_media = 0x40;
- config = inl(ioaddr + Wn3_Config);
+ config = ioread32(ioaddr + Wn3_Config);
if (print_info) {
printk(KERN_DEBUG " Internal config register is %4.4x, "
- "transceivers %#x.\n", config, inw(ioaddr + Wn3_Options));
+ "transceivers %#x.\n", config, ioread16(ioaddr + Wn3_Options));
printk(KERN_INFO " %dK %s-wide RAM %s Rx:Tx split, %s%s interface.\n",
8 << RAM_SIZE(config),
RAM_WIDTH(config) ? "word" : "byte",
@@ -1555,7 +1557,7 @@
vp->rx_ring_dma);
free_region:
if (vp->must_free_region)
- release_region(ioaddr, vci->io_size);
+ release_region(dev->base_addr, vci->io_size);
free_netdev(dev);
printk(KERN_ERR PFX "vortex_probe1 fails. Returns %d\n", retval);
out:
@@ -1565,17 +1567,19 @@
static void
issue_and_wait(struct net_device *dev, int cmd)
{
+ struct vortex_private *vp = netdev_priv(dev);
+ void __iomem *ioaddr = vp->ioaddr;
int i;
- outw(cmd, dev->base_addr + EL3_CMD);
+ iowrite16(cmd, ioaddr + EL3_CMD);
for (i = 0; i < 2000; i++) {
- if (!(inw(dev->base_addr + EL3_STATUS) & CmdInProgress))
+ if (!(ioread16(ioaddr + EL3_STATUS) & CmdInProgress))
return;
}
/* OK, that didn't work. Do it the slow way. One second */
for (i = 0; i < 100000; i++) {
- if (!(inw(dev->base_addr + EL3_STATUS) & CmdInProgress)) {
+ if (!(ioread16(ioaddr + EL3_STATUS) & CmdInProgress)) {
if (vortex_debug > 1)
printk(KERN_INFO "%s: command 0x%04x took %d usecs\n",
dev->name, cmd, i * 10);
@@ -1584,14 +1588,14 @@
udelay(10);
}
printk(KERN_ERR "%s: command 0x%04x did not complete! Status=0x%x\n",
- dev->name, cmd, inw(dev->base_addr + EL3_STATUS));
+ dev->name, cmd, ioread16(ioaddr + EL3_STATUS));
}
static void
vortex_up(struct net_device *dev)
{
- long ioaddr = dev->base_addr;
struct vortex_private *vp = netdev_priv(dev);
+ void __iomem *ioaddr = vp->ioaddr;
unsigned int config;
int i;
@@ -1604,7 +1608,7 @@
/* Before initializing select the active media port. */
EL3WINDOW(3);
- config = inl(ioaddr + Wn3_Config);
+ config = ioread32(ioaddr + Wn3_Config);
if (vp->media_override != 7) {
printk(KERN_INFO "%s: Media override to transceiver %d (%s).\n",
@@ -1651,7 +1655,7 @@
config = BFINS(config, dev->if_port, 20, 4);
if (vortex_debug > 6)
printk(KERN_DEBUG "vortex_up(): writing 0x%x to InternalConfig\n", config);
- outl(config, ioaddr + Wn3_Config);
+ iowrite32(config, ioaddr + Wn3_Config);
if (dev->if_port == XCVR_MII || dev->if_port == XCVR_NWAY) {
int mii_reg1, mii_reg5;
@@ -1679,7 +1683,7 @@
}
/* Set the full-duplex bit. */
- outw( ((vp->info1 & 0x8000) || vp->full_duplex ? 0x20 : 0) |
+ iowrite16( ((vp->info1 & 0x8000) || vp->full_duplex ? 0x20 : 0) |
(vp->large_frames ? 0x40 : 0) |
((vp->full_duplex && vp->flow_ctrl && vp->partner_flow_ctrl) ? 0x100 : 0),
ioaddr + Wn3_MAC_Ctrl);
@@ -1695,51 +1699,51 @@
*/
issue_and_wait(dev, RxReset|0x04);
- outw(SetStatusEnb | 0x00, ioaddr + EL3_CMD);
+ iowrite16(SetStatusEnb | 0x00, ioaddr + EL3_CMD);
if (vortex_debug > 1) {
EL3WINDOW(4);
printk(KERN_DEBUG "%s: vortex_up() irq %d media status %4.4x.\n",
- dev->name, dev->irq, inw(ioaddr + Wn4_Media));
+ dev->name, dev->irq, ioread16(ioaddr + Wn4_Media));
}
/* Set the station address and mask in window 2 each time opened. */
EL3WINDOW(2);
for (i = 0; i < 6; i++)
- outb(dev->dev_addr[i], ioaddr + i);
+ iowrite8(dev->dev_addr[i], ioaddr + i);
for (; i < 12; i+=2)
- outw(0, ioaddr + i);
+ iowrite16(0, ioaddr + i);
if (vp->cb_fn_base) {
- unsigned short n = inw(ioaddr + Wn2_ResetOptions) & ~0x4010;
+ unsigned short n = ioread16(ioaddr + Wn2_ResetOptions) & ~0x4010;
if (vp->drv_flags & INVERT_LED_PWR)
n |= 0x10;
if (vp->drv_flags & INVERT_MII_PWR)
n |= 0x4000;
- outw(n, ioaddr + Wn2_ResetOptions);
+ iowrite16(n, ioaddr + Wn2_ResetOptions);
}
if (dev->if_port == XCVR_10base2)
/* Start the thinnet transceiver. We should really wait 50ms...*/
- outw(StartCoax, ioaddr + EL3_CMD);
+ iowrite16(StartCoax, ioaddr + EL3_CMD);
if (dev->if_port != XCVR_NWAY) {
EL3WINDOW(4);
- outw((inw(ioaddr + Wn4_Media) & ~(Media_10TP|Media_SQE)) |
+ iowrite16((ioread16(ioaddr + Wn4_Media) & ~(Media_10TP|Media_SQE)) |
media_tbl[dev->if_port].media_bits, ioaddr + Wn4_Media);
}
/* Switch to the stats window, and clear all stats by reading. */
- outw(StatsDisable, ioaddr + EL3_CMD);
+ iowrite16(StatsDisable, ioaddr + EL3_CMD);
EL3WINDOW(6);
for (i = 0; i < 10; i++)
- inb(ioaddr + i);
- inw(ioaddr + 10);
- inw(ioaddr + 12);
+ ioread8(ioaddr + i);
+ ioread16(ioaddr + 10);
+ ioread16(ioaddr + 12);
/* New: On the Vortex we must also clear the BadSSD counter. */
EL3WINDOW(4);
- inb(ioaddr + 12);
+ ioread8(ioaddr + 12);
/* ..and on the Boomerang we enable the extra statistics bits. */
- outw(0x0040, ioaddr + Wn4_NetDiag);
+ iowrite16(0x0040, ioaddr + Wn4_NetDiag);
/* Switch to register set 7 for normal use. */
EL3WINDOW(7);
@@ -1747,30 +1751,30 @@
if (vp->full_bus_master_rx) { /* Boomerang bus master. */
vp->cur_rx = vp->dirty_rx = 0;
/* Initialize the RxEarly register as recommended. */
- outw(SetRxThreshold + (1536>>2), ioaddr + EL3_CMD);
- outl(0x0020, ioaddr + PktStatus);
- outl(vp->rx_ring_dma, ioaddr + UpListPtr);
+ iowrite16(SetRxThreshold + (1536>>2), ioaddr + EL3_CMD);
+ iowrite32(0x0020, ioaddr + PktStatus);
+ iowrite32(vp->rx_ring_dma, ioaddr + UpListPtr);
}
if (vp->full_bus_master_tx) { /* Boomerang bus master Tx. */
vp->cur_tx = vp->dirty_tx = 0;
if (vp->drv_flags & IS_BOOMERANG)
- outb(PKT_BUF_SZ>>8, ioaddr + TxFreeThreshold); /* Room for a packet. */
+ iowrite8(PKT_BUF_SZ>>8, ioaddr + TxFreeThreshold); /* Room for a packet. */
/* Clear the Rx, Tx rings. */
for (i = 0; i < RX_RING_SIZE; i++) /* AKPM: this is done in vortex_open, too */
vp->rx_ring[i].status = 0;
for (i = 0; i < TX_RING_SIZE; i++)
vp->tx_skbuff[i] = NULL;
- outl(0, ioaddr + DownListPtr);
+ iowrite32(0, ioaddr + DownListPtr);
}
/* Set receiver mode: presumably accept b-case and phys addr only. */
set_rx_mode(dev);
/* enable 802.1q tagged frames */
set_8021q_mode(dev, 1);
- outw(StatsEnable, ioaddr + EL3_CMD); /* Turn on statistics. */
+ iowrite16(StatsEnable, ioaddr + EL3_CMD); /* Turn on statistics. */
// issue_and_wait(dev, SetTxStart|0x07ff);
- outw(RxEnable, ioaddr + EL3_CMD); /* Enable the receiver. */
- outw(TxEnable, ioaddr + EL3_CMD); /* Enable transmitter. */
+ iowrite16(RxEnable, ioaddr + EL3_CMD); /* Enable the receiver. */
+ iowrite16(TxEnable, ioaddr + EL3_CMD); /* Enable transmitter. */
/* Allow status bits to be seen. */
vp->status_enable = SetStatusEnb | HostError|IntReq|StatsFull|TxComplete|
(vp->full_bus_master_tx ? DownComplete : TxAvailable) |
@@ -1780,13 +1784,13 @@
(vp->full_bus_master_rx ? 0 : RxComplete) |
StatsFull | HostError | TxComplete | IntReq
| (vp->bus_master ? DMADone : 0) | UpComplete | DownComplete;
- outw(vp->status_enable, ioaddr + EL3_CMD);
+ iowrite16(vp->status_enable, ioaddr + EL3_CMD);
/* Ack all pending events, and set active indicator mask. */
- outw(AckIntr | IntLatch | TxAvailable | RxEarly | IntReq,
+ iowrite16(AckIntr | IntLatch | TxAvailable | RxEarly | IntReq,
ioaddr + EL3_CMD);
- outw(vp->intr_enable, ioaddr + EL3_CMD);
+ iowrite16(vp->intr_enable, ioaddr + EL3_CMD);
if (vp->cb_fn_base) /* The PCMCIA people are idiots. */
- writel(0x8000, vp->cb_fn_base + 4);
+ iowrite32(0x8000, vp->cb_fn_base + 4);
netif_start_queue (dev);
}
@@ -1852,7 +1856,7 @@
{
struct net_device *dev = (struct net_device *)data;
struct vortex_private *vp = netdev_priv(dev);
- long ioaddr = dev->base_addr;
+ void __iomem *ioaddr = vp->ioaddr;
int next_tick = 60*HZ;
int ok = 0;
int media_status, mii_status, old_window;
@@ -1866,9 +1870,9 @@
if (vp->medialock)
goto leave_media_alone;
disable_irq(dev->irq);
- old_window = inw(ioaddr + EL3_CMD) >> 13;
+ old_window = ioread16(ioaddr + EL3_CMD) >> 13;
EL3WINDOW(4);
- media_status = inw(ioaddr + Wn4_Media);
+ media_status = ioread16(ioaddr + Wn4_Media);
switch (dev->if_port) {
case XCVR_10baseT: case XCVR_100baseTx: case XCVR_100baseFx:
if (media_status & Media_LnkBeat) {
@@ -1909,7 +1913,7 @@
vp->phys[0], mii_reg5);
/* Set the full-duplex bit. */
EL3WINDOW(3);
- outw( (vp->full_duplex ? 0x20 : 0) |
+ iowrite16( (vp->full_duplex ? 0x20 : 0) |
(vp->large_frames ? 0x40 : 0) |
((vp->full_duplex && vp->flow_ctrl && vp->partner_flow_ctrl) ? 0x100 : 0),
ioaddr + Wn3_MAC_Ctrl);
@@ -1950,15 +1954,15 @@
dev->name, media_tbl[dev->if_port].name);
next_tick = media_tbl[dev->if_port].wait;
}
- outw((media_status & ~(Media_10TP|Media_SQE)) |
+ iowrite16((media_status & ~(Media_10TP|Media_SQE)) |
media_tbl[dev->if_port].media_bits, ioaddr + Wn4_Media);
EL3WINDOW(3);
- config = inl(ioaddr + Wn3_Config);
+ config = ioread32(ioaddr + Wn3_Config);
config = BFINS(config, dev->if_port, 20, 4);
- outl(config, ioaddr + Wn3_Config);
+ iowrite32(config, ioaddr + Wn3_Config);
- outw(dev->if_port == XCVR_10base2 ? StartCoax : StopCoax,
+ iowrite16(dev->if_port == XCVR_10base2 ? StartCoax : StopCoax,
ioaddr + EL3_CMD);
if (vortex_debug > 1)
printk(KERN_DEBUG "wrote 0x%08x to Wn3_Config\n", config);
@@ -1974,29 +1978,29 @@
mod_timer(&vp->timer, RUN_AT(next_tick));
if (vp->deferred)
- outw(FakeIntr, ioaddr + EL3_CMD);
+ iowrite16(FakeIntr, ioaddr + EL3_CMD);
return;
}
static void vortex_tx_timeout(struct net_device *dev)
{
struct vortex_private *vp = netdev_priv(dev);
- long ioaddr = dev->base_addr;
+ void __iomem *ioaddr = vp->ioaddr;
printk(KERN_ERR "%s: transmit timed out, tx_status %2.2x status %4.4x.\n",
- dev->name, inb(ioaddr + TxStatus),
- inw(ioaddr + EL3_STATUS));
+ dev->name, ioread8(ioaddr + TxStatus),
+ ioread16(ioaddr + EL3_STATUS));
EL3WINDOW(4);
printk(KERN_ERR " diagnostics: net %04x media %04x dma %08x fifo %04x\n",
- inw(ioaddr + Wn4_NetDiag),
- inw(ioaddr + Wn4_Media),
- inl(ioaddr + PktStatus),
- inw(ioaddr + Wn4_FIFODiag));
+ ioread16(ioaddr + Wn4_NetDiag),
+ ioread16(ioaddr + Wn4_Media),
+ ioread32(ioaddr + PktStatus),
+ ioread16(ioaddr + Wn4_FIFODiag));
/* Slight code bloat to be user friendly. */
- if ((inb(ioaddr + TxStatus) & 0x88) == 0x88)
+ if ((ioread8(ioaddr + TxStatus) & 0x88) == 0x88)
printk(KERN_ERR "%s: Transmitter encountered 16 collisions --"
" network cable problem?\n", dev->name);
- if (inw(ioaddr + EL3_STATUS) & IntLatch) {
+ if (ioread16(ioaddr + EL3_STATUS) & IntLatch) {
printk(KERN_ERR "%s: Interrupt posted but not delivered --"
" IRQ blocked by another device?\n", dev->name);
/* Bad idea here.. but we might as well handle a few events. */
@@ -2022,21 +2026,21 @@
vp->stats.tx_errors++;
if (vp->full_bus_master_tx) {
printk(KERN_DEBUG "%s: Resetting the Tx ring pointer.\n", dev->name);
- if (vp->cur_tx - vp->dirty_tx > 0 && inl(ioaddr + DownListPtr) == 0)
- outl(vp->tx_ring_dma + (vp->dirty_tx % TX_RING_SIZE) * sizeof(struct boom_tx_desc),
+ if (vp->cur_tx - vp->dirty_tx > 0 && ioread32(ioaddr + DownListPtr) == 0)
+ iowrite32(vp->tx_ring_dma + (vp->dirty_tx % TX_RING_SIZE) * sizeof(struct boom_tx_desc),
ioaddr + DownListPtr);
if (vp->cur_tx - vp->dirty_tx < TX_RING_SIZE)
netif_wake_queue (dev);
if (vp->drv_flags & IS_BOOMERANG)
- outb(PKT_BUF_SZ>>8, ioaddr + TxFreeThreshold);
- outw(DownUnstall, ioaddr + EL3_CMD);
+ iowrite8(PKT_BUF_SZ>>8, ioaddr + TxFreeThreshold);
+ iowrite16(DownUnstall, ioaddr + EL3_CMD);
} else {
vp->stats.tx_dropped++;
netif_wake_queue(dev);
}
/* Issue Tx Enable */
- outw(TxEnable, ioaddr + EL3_CMD);
+ iowrite16(TxEnable, ioaddr + EL3_CMD);
dev->trans_start = jiffies;
/* Switch to register set 7 for normal use. */
@@ -2051,7 +2055,7 @@
vortex_error(struct net_device *dev, int status)
{
struct vortex_private *vp = netdev_priv(dev);
- long ioaddr = dev->base_addr;
+ void __iomem *ioaddr = vp->ioaddr;
int do_tx_reset = 0, reset_mask = 0;
unsigned char tx_status = 0;
@@ -2060,7 +2064,7 @@
}
if (status & TxComplete) { /* Really "TxError" for us. */
- tx_status = inb(ioaddr + TxStatus);
+ tx_status = ioread8(ioaddr + TxStatus);
/* Presumably a tx-timeout. We must merely re-enable. */
if (vortex_debug > 2
|| (tx_status != 0x88 && vortex_debug > 0)) {
@@ -2074,20 +2078,20 @@
}
if (tx_status & 0x14) vp->stats.tx_fifo_errors++;
if (tx_status & 0x38) vp->stats.tx_aborted_errors++;
- outb(0, ioaddr + TxStatus);
+ iowrite8(0, ioaddr + TxStatus);
if (tx_status & 0x30) { /* txJabber or txUnderrun */
do_tx_reset = 1;
} else if ((tx_status & 0x08) && (vp->drv_flags & MAX_COLLISION_RESET)) { /* maxCollisions */
do_tx_reset = 1;
reset_mask = 0x0108; /* Reset interface logic, but not download logic */
} else { /* Merely re-enable the transmitter. */
- outw(TxEnable, ioaddr + EL3_CMD);
+ iowrite16(TxEnable, ioaddr + EL3_CMD);
}
}
if (status & RxEarly) { /* Rx early is unused. */
vortex_rx(dev);
- outw(AckIntr | RxEarly, ioaddr + EL3_CMD);
+ iowrite16(AckIntr | RxEarly, ioaddr + EL3_CMD);
}
if (status & StatsFull) { /* Empty statistics. */
static int DoneDidThat;
@@ -2097,29 +2101,29 @@
/* HACK: Disable statistics as an interrupt source. */
/* This occurs when we have the wrong media type! */
if (DoneDidThat == 0 &&
- inw(ioaddr + EL3_STATUS) & StatsFull) {
+ ioread16(ioaddr + EL3_STATUS) & StatsFull) {
printk(KERN_WARNING "%s: Updating statistics failed, disabling "
"stats as an interrupt source.\n", dev->name);
EL3WINDOW(5);
- outw(SetIntrEnb | (inw(ioaddr + 10) & ~StatsFull), ioaddr + EL3_CMD);
+ iowrite16(SetIntrEnb | (ioread16(ioaddr + 10) & ~StatsFull), ioaddr + EL3_CMD);
vp->intr_enable &= ~StatsFull;
EL3WINDOW(7);
DoneDidThat++;
}
}
if (status & IntReq) { /* Restore all interrupt sources. */
- outw(vp->status_enable, ioaddr + EL3_CMD);
- outw(vp->intr_enable, ioaddr + EL3_CMD);
+ iowrite16(vp->status_enable, ioaddr + EL3_CMD);
+ iowrite16(vp->intr_enable, ioaddr + EL3_CMD);
}
if (status & HostError) {
u16 fifo_diag;
EL3WINDOW(4);
- fifo_diag = inw(ioaddr + Wn4_FIFODiag);
+ fifo_diag = ioread16(ioaddr + Wn4_FIFODiag);
printk(KERN_ERR "%s: Host error, FIFO diagnostic register %4.4x.\n",
dev->name, fifo_diag);
/* Adapter failure requires Tx/Rx reset and reinit. */
if (vp->full_bus_master_tx) {
- int bus_status = inl(ioaddr + PktStatus);
+ int bus_status = ioread32(ioaddr + PktStatus);
/* 0x80000000 PCI master abort. */
/* 0x40000000 PCI target abort. */
if (vortex_debug)
@@ -2139,14 +2143,14 @@
set_rx_mode(dev);
/* enable 802.1q VLAN tagged frames */
set_8021q_mode(dev, 1);
- outw(RxEnable, ioaddr + EL3_CMD); /* Re-enable the receiver. */
- outw(AckIntr | HostError, ioaddr + EL3_CMD);
+ iowrite16(RxEnable, ioaddr + EL3_CMD); /* Re-enable the receiver. */
+ iowrite16(AckIntr | HostError, ioaddr + EL3_CMD);
}
}
if (do_tx_reset) {
issue_and_wait(dev, TxReset|reset_mask);
- outw(TxEnable, ioaddr + EL3_CMD);
+ iowrite16(TxEnable, ioaddr + EL3_CMD);
if (!vp->full_bus_master_tx)
netif_wake_queue(dev);
}
@@ -2156,29 +2160,29 @@
vortex_start_xmit(struct sk_buff *skb, struct net_device *dev)
{
struct vortex_private *vp = netdev_priv(dev);
- long ioaddr = dev->base_addr;
+ void __iomem *ioaddr = vp->ioaddr;
/* Put out the doubleword header... */
- outl(skb->len, ioaddr + TX_FIFO);
+ iowrite32(skb->len, ioaddr + TX_FIFO);
if (vp->bus_master) {
/* Set the bus-master controller to transfer the packet. */
int len = (skb->len + 3) & ~3;
- outl( vp->tx_skb_dma = pci_map_single(VORTEX_PCI(vp), skb->data, len, PCI_DMA_TODEVICE),
+ iowrite32( vp->tx_skb_dma = pci_map_single(VORTEX_PCI(vp), skb->data, len, PCI_DMA_TODEVICE),
ioaddr + Wn7_MasterAddr);
- outw(len, ioaddr + Wn7_MasterLen);
+ iowrite16(len, ioaddr + Wn7_MasterLen);
vp->tx_skb = skb;
- outw(StartDMADown, ioaddr + EL3_CMD);
+ iowrite16(StartDMADown, ioaddr + EL3_CMD);
/* netif_wake_queue() will be called at the DMADone interrupt. */
} else {
/* ... and the packet rounded to a doubleword. */
- outsl(ioaddr + TX_FIFO, skb->data, (skb->len + 3) >> 2);
+ iowrite32_rep(ioaddr + TX_FIFO, skb->data, (skb->len + 3) >> 2);
dev_kfree_skb (skb);
- if (inw(ioaddr + TxFree) > 1536) {
+ if (ioread16(ioaddr + TxFree) > 1536) {
netif_start_queue (dev); /* AKPM: redundant? */
} else {
/* Interrupt us when the FIFO has room for max-sized packet. */
netif_stop_queue(dev);
- outw(SetTxThreshold + (1536>>2), ioaddr + EL3_CMD);
+ iowrite16(SetTxThreshold + (1536>>2), ioaddr + EL3_CMD);
}
}
@@ -2189,7 +2193,7 @@
int tx_status;
int i = 32;
- while (--i > 0 && (tx_status = inb(ioaddr + TxStatus)) > 0) {
+ while (--i > 0 && (tx_status = ioread8(ioaddr + TxStatus)) > 0) {
if (tx_status & 0x3C) { /* A Tx-disabling error occurred. */
if (vortex_debug > 2)
printk(KERN_DEBUG "%s: Tx error, status %2.2x.\n",
@@ -2199,9 +2203,9 @@
if (tx_status & 0x30) {
issue_and_wait(dev, TxReset);
}
- outw(TxEnable, ioaddr + EL3_CMD);
+ iowrite16(TxEnable, ioaddr + EL3_CMD);
}
- outb(0x00, ioaddr + TxStatus); /* Pop the status stack. */
+ iowrite8(0x00, ioaddr + TxStatus); /* Pop the status stack. */
}
}
return 0;
@@ -2211,7 +2215,7 @@
boomerang_start_xmit(struct sk_buff *skb, struct net_device *dev)
{
struct vortex_private *vp = netdev_priv(dev);
- long ioaddr = dev->base_addr;
+ void __iomem *ioaddr = vp->ioaddr;
/* Calculate the next Tx descriptor entry. */
int entry = vp->cur_tx % TX_RING_SIZE;
struct boom_tx_desc *prev_entry = &vp->tx_ring[(vp->cur_tx-1) % TX_RING_SIZE];
@@ -2275,8 +2279,8 @@
/* Wait for the stall to complete. */
issue_and_wait(dev, DownStall);
prev_entry->next = cpu_to_le32(vp->tx_ring_dma + entry * sizeof(struct boom_tx_desc));
- if (inl(ioaddr + DownListPtr) == 0) {
- outl(vp->tx_ring_dma + entry * sizeof(struct boom_tx_desc), ioaddr + DownListPtr);
+ if (ioread32(ioaddr + DownListPtr) == 0) {
+ iowrite32(vp->tx_ring_dma + entry * sizeof(struct boom_tx_desc), ioaddr + DownListPtr);
vp->queued_packet++;
}
@@ -2291,7 +2295,7 @@
prev_entry->status &= cpu_to_le32(~TxIntrUploaded);
#endif
}
- outw(DownUnstall, ioaddr + EL3_CMD);
+ iowrite16(DownUnstall, ioaddr + EL3_CMD);
spin_unlock_irqrestore(&vp->lock, flags);
dev->trans_start = jiffies;
return 0;
@@ -2310,15 +2314,15 @@
{
struct net_device *dev = dev_id;
struct vortex_private *vp = netdev_priv(dev);
- long ioaddr;
+ void __iomem *ioaddr;
int status;
int work_done = max_interrupt_work;
int handled = 0;
- ioaddr = dev->base_addr;
+ ioaddr = vp->ioaddr;
spin_lock(&vp->lock);
- status = inw(ioaddr + EL3_STATUS);
+ status = ioread16(ioaddr + EL3_STATUS);
if (vortex_debug > 6)
printk("vortex_interrupt(). status=0x%4x\n", status);
@@ -2337,7 +2341,7 @@
if (vortex_debug > 4)
printk(KERN_DEBUG "%s: interrupt, status %4.4x, latency %d ticks.\n",
- dev->name, status, inb(ioaddr + Timer));
+ dev->name, status, ioread8(ioaddr + Timer));
do {
if (vortex_debug > 5)
@@ -2350,16 +2354,16 @@
if (vortex_debug > 5)
printk(KERN_DEBUG " TX room bit was handled.\n");
/* There's room in the FIFO for a full-sized packet. */
- outw(AckIntr | TxAvailable, ioaddr + EL3_CMD);
+ iowrite16(AckIntr | TxAvailable, ioaddr + EL3_CMD);
netif_wake_queue (dev);
}
if (status & DMADone) {
- if (inw(ioaddr + Wn7_MasterStatus) & 0x1000) {
- outw(0x1000, ioaddr + Wn7_MasterStatus); /* Ack the event. */
+ if (ioread16(ioaddr + Wn7_MasterStatus) & 0x1000) {
+ iowrite16(0x1000, ioaddr + Wn7_MasterStatus); /* Ack the event. */
pci_unmap_single(VORTEX_PCI(vp), vp->tx_skb_dma, (vp->tx_skb->len + 3) & ~3, PCI_DMA_TODEVICE);
dev_kfree_skb_irq(vp->tx_skb); /* Release the transferred buffer */
- if (inw(ioaddr + TxFree) > 1536) {
+ if (ioread16(ioaddr + TxFree) > 1536) {
/*
* AKPM: FIXME: I don't think we need this. If the queue was stopped due to
* insufficient FIFO room, the TxAvailable test will succeed and call
@@ -2367,7 +2371,7 @@
*/
netif_wake_queue(dev);
} else { /* Interrupt when FIFO has room for max-sized packet. */
- outw(SetTxThreshold + (1536>>2), ioaddr + EL3_CMD);
+ iowrite16(SetTxThreshold + (1536>>2), ioaddr + EL3_CMD);
netif_stop_queue(dev);
}
}
@@ -2385,17 +2389,17 @@
/* Disable all pending interrupts. */
do {
vp->deferred |= status;
- outw(SetStatusEnb | (~vp->deferred & vp->status_enable),
+ iowrite16(SetStatusEnb | (~vp->deferred & vp->status_enable),
ioaddr + EL3_CMD);
- outw(AckIntr | (vp->deferred & 0x7ff), ioaddr + EL3_CMD);
- } while ((status = inw(ioaddr + EL3_CMD)) & IntLatch);
+ iowrite16(AckIntr | (vp->deferred & 0x7ff), ioaddr + EL3_CMD);
+ } while ((status = ioread16(ioaddr + EL3_CMD)) & IntLatch);
/* The timer will reenable interrupts. */
mod_timer(&vp->timer, jiffies + 1*HZ);
break;
}
/* Acknowledge the IRQ. */
- outw(AckIntr | IntReq | IntLatch, ioaddr + EL3_CMD);
- } while ((status = inw(ioaddr + EL3_STATUS)) & (IntLatch | RxComplete));
+ iowrite16(AckIntr | IntReq | IntLatch, ioaddr + EL3_CMD);
+ } while ((status = ioread16(ioaddr + EL3_STATUS)) & (IntLatch | RxComplete));
if (vortex_debug > 4)
printk(KERN_DEBUG "%s: exiting interrupt, status %4.4x.\n",
@@ -2415,11 +2419,11 @@
{
struct net_device *dev = dev_id;
struct vortex_private *vp = netdev_priv(dev);
- long ioaddr;
+ void __iomem *ioaddr;
int status;
int work_done = max_interrupt_work;
- ioaddr = dev->base_addr;
+ ioaddr = vp->ioaddr;
/*
* It seems dopey to put the spinlock this early, but we could race against vortex_tx_timeout
@@ -2427,7 +2431,7 @@
*/
spin_lock(&vp->lock);
- status = inw(ioaddr + EL3_STATUS);
+ status = ioread16(ioaddr + EL3_STATUS);
if (vortex_debug > 6)
printk(KERN_DEBUG "boomerang_interrupt. status=0x%4x\n", status);
@@ -2448,13 +2452,13 @@
if (vortex_debug > 4)
printk(KERN_DEBUG "%s: interrupt, status %4.4x, latency %d ticks.\n",
- dev->name, status, inb(ioaddr + Timer));
+ dev->name, status, ioread8(ioaddr + Timer));
do {
if (vortex_debug > 5)
printk(KERN_DEBUG "%s: In interrupt loop, status %4.4x.\n",
dev->name, status);
if (status & UpComplete) {
- outw(AckIntr | UpComplete, ioaddr + EL3_CMD);
+ iowrite16(AckIntr | UpComplete, ioaddr + EL3_CMD);
if (vortex_debug > 5)
printk(KERN_DEBUG "boomerang_interrupt->boomerang_rx\n");
boomerang_rx(dev);
@@ -2463,11 +2467,11 @@
if (status & DownComplete) {
unsigned int dirty_tx = vp->dirty_tx;
- outw(AckIntr | DownComplete, ioaddr + EL3_CMD);
+ iowrite16(AckIntr | DownComplete, ioaddr + EL3_CMD);
while (vp->cur_tx - dirty_tx > 0) {
int entry = dirty_tx % TX_RING_SIZE;
#if 1 /* AKPM: the latter is faster, but cyclone-only */
- if (inl(ioaddr + DownListPtr) ==
+ if (ioread32(ioaddr + DownListPtr) ==
vp->tx_ring_dma + entry * sizeof(struct boom_tx_desc))
break; /* It still hasn't been processed. */
#else
@@ -2514,20 +2518,20 @@
/* Disable all pending interrupts. */
do {
vp->deferred |= status;
- outw(SetStatusEnb | (~vp->deferred & vp->status_enable),
+ iowrite16(SetStatusEnb | (~vp->deferred & vp->status_enable),
ioaddr + EL3_CMD);
- outw(AckIntr | (vp->deferred & 0x7ff), ioaddr + EL3_CMD);
- } while ((status = inw(ioaddr + EL3_CMD)) & IntLatch);
+ iowrite16(AckIntr | (vp->deferred & 0x7ff), ioaddr + EL3_CMD);
+ } while ((status = ioread16(ioaddr + EL3_CMD)) & IntLatch);
/* The timer will reenable interrupts. */
mod_timer(&vp->timer, jiffies + 1*HZ);
break;
}
/* Acknowledge the IRQ. */
- outw(AckIntr | IntReq | IntLatch, ioaddr + EL3_CMD);
+ iowrite16(AckIntr | IntReq | IntLatch, ioaddr + EL3_CMD);
if (vp->cb_fn_base) /* The PCMCIA people are idiots. */
- writel(0x8000, vp->cb_fn_base + 4);
+ iowrite32(0x8000, vp->cb_fn_base + 4);
- } while ((status = inw(ioaddr + EL3_STATUS)) & IntLatch);
+ } while ((status = ioread16(ioaddr + EL3_STATUS)) & IntLatch);
if (vortex_debug > 4)
printk(KERN_DEBUG "%s: exiting interrupt, status %4.4x.\n",
@@ -2540,16 +2544,16 @@
static int vortex_rx(struct net_device *dev)
{
struct vortex_private *vp = netdev_priv(dev);
- long ioaddr = dev->base_addr;
+ void __iomem *ioaddr = vp->ioaddr;
int i;
short rx_status;
if (vortex_debug > 5)
printk(KERN_DEBUG "vortex_rx(): status %4.4x, rx_status %4.4x.\n",
- inw(ioaddr+EL3_STATUS), inw(ioaddr+RxStatus));
- while ((rx_status = inw(ioaddr + RxStatus)) > 0) {
+ ioread16(ioaddr+EL3_STATUS), ioread16(ioaddr+RxStatus));
+ while ((rx_status = ioread16(ioaddr + RxStatus)) > 0) {
if (rx_status & 0x4000) { /* Error, update stats. */
- unsigned char rx_error = inb(ioaddr + RxErrors);
+ unsigned char rx_error = ioread8(ioaddr + RxErrors);
if (vortex_debug > 2)
printk(KERN_DEBUG " Rx error: status %2.2x.\n", rx_error);
vp->stats.rx_errors++;
@@ -2572,27 +2576,28 @@
skb_reserve(skb, 2); /* Align IP on 16 byte boundaries */
/* 'skb_put()' points to the start of sk_buff data area. */
if (vp->bus_master &&
- ! (inw(ioaddr + Wn7_MasterStatus) & 0x8000)) {
+ ! (ioread16(ioaddr + Wn7_MasterStatus) & 0x8000)) {
dma_addr_t dma = pci_map_single(VORTEX_PCI(vp), skb_put(skb, pkt_len),
pkt_len, PCI_DMA_FROMDEVICE);
- outl(dma, ioaddr + Wn7_MasterAddr);
- outw((skb->len + 3) & ~3, ioaddr + Wn7_MasterLen);
- outw(StartDMAUp, ioaddr + EL3_CMD);
- while (inw(ioaddr + Wn7_MasterStatus) & 0x8000)
+ iowrite32(dma, ioaddr + Wn7_MasterAddr);
+ iowrite16((skb->len + 3) & ~3, ioaddr + Wn7_MasterLen);
+ iowrite16(StartDMAUp, ioaddr + EL3_CMD);
+ while (ioread16(ioaddr + Wn7_MasterStatus) & 0x8000)
;
pci_unmap_single(VORTEX_PCI(vp), dma, pkt_len, PCI_DMA_FROMDEVICE);
} else {
- insl(ioaddr + RX_FIFO, skb_put(skb, pkt_len),
- (pkt_len + 3) >> 2);
+ ioread32_rep(ioaddr + RX_FIFO,
+ skb_put(skb, pkt_len),
+ (pkt_len + 3) >> 2);
}
- outw(RxDiscard, ioaddr + EL3_CMD); /* Pop top Rx packet. */
+ iowrite16(RxDiscard, ioaddr + EL3_CMD); /* Pop top Rx packet. */
skb->protocol = eth_type_trans(skb, dev);
netif_rx(skb);
dev->last_rx = jiffies;
vp->stats.rx_packets++;
/* Wait a limited time to go to next packet. */
for (i = 200; i >= 0; i--)
- if ( ! (inw(ioaddr + EL3_STATUS) & CmdInProgress))
+ if ( ! (ioread16(ioaddr + EL3_STATUS) & CmdInProgress))
break;
continue;
} else if (vortex_debug > 0)
@@ -2611,12 +2616,12 @@
{
struct vortex_private *vp = netdev_priv(dev);
int entry = vp->cur_rx % RX_RING_SIZE;
- long ioaddr = dev->base_addr;
+ void __iomem *ioaddr = vp->ioaddr;
int rx_status;
int rx_work_limit = vp->dirty_rx + RX_RING_SIZE - vp->cur_rx;
if (vortex_debug > 5)
- printk(KERN_DEBUG "boomerang_rx(): status %4.4x\n", inw(ioaddr+EL3_STATUS));
+ printk(KERN_DEBUG "boomerang_rx(): status %4.4x\n", ioread16(ioaddr+EL3_STATUS));
while ((rx_status = le32_to_cpu(vp->rx_ring[entry].status)) & RxDComplete){
if (--rx_work_limit < 0)
@@ -2699,7 +2704,7 @@
vp->rx_skbuff[entry] = skb;
}
vp->rx_ring[entry].status = 0; /* Clear complete bit. */
- outw(UpUnstall, ioaddr + EL3_CMD);
+ iowrite16(UpUnstall, ioaddr + EL3_CMD);
}
return 0;
}
@@ -2728,7 +2733,7 @@
vortex_down(struct net_device *dev, int final_down)
{
struct vortex_private *vp = netdev_priv(dev);
- long ioaddr = dev->base_addr;
+ void __iomem *ioaddr = vp->ioaddr;
netif_stop_queue (dev);
@@ -2736,26 +2741,26 @@
del_timer_sync(&vp->timer);
/* Turn off statistics ASAP. We update vp->stats below. */
- outw(StatsDisable, ioaddr + EL3_CMD);
+ iowrite16(StatsDisable, ioaddr + EL3_CMD);
/* Disable the receiver and transmitter. */
- outw(RxDisable, ioaddr + EL3_CMD);
- outw(TxDisable, ioaddr + EL3_CMD);
+ iowrite16(RxDisable, ioaddr + EL3_CMD);
+ iowrite16(TxDisable, ioaddr + EL3_CMD);
/* Disable receiving 802.1q tagged frames */
set_8021q_mode(dev, 0);
if (dev->if_port == XCVR_10base2)
/* Turn off thinnet power. Green! */
- outw(StopCoax, ioaddr + EL3_CMD);
+ iowrite16(StopCoax, ioaddr + EL3_CMD);
- outw(SetIntrEnb | 0x0000, ioaddr + EL3_CMD);
+ iowrite16(SetIntrEnb | 0x0000, ioaddr + EL3_CMD);
update_stats(ioaddr, dev);
if (vp->full_bus_master_rx)
- outl(0, ioaddr + UpListPtr);
+ iowrite32(0, ioaddr + UpListPtr);
if (vp->full_bus_master_tx)
- outl(0, ioaddr + DownListPtr);
+ iowrite32(0, ioaddr + DownListPtr);
if (final_down && VORTEX_PCI(vp)) {
vp->pm_state_valid = 1;
@@ -2768,7 +2773,7 @@
vortex_close(struct net_device *dev)
{
struct vortex_private *vp = netdev_priv(dev);
- long ioaddr = dev->base_addr;
+ void __iomem *ioaddr = vp->ioaddr;
int i;
if (netif_device_present(dev))
@@ -2776,7 +2781,7 @@
if (vortex_debug > 1) {
printk(KERN_DEBUG"%s: vortex_close() status %4.4x, Tx status %2.2x.\n",
- dev->name, inw(ioaddr + EL3_STATUS), inb(ioaddr + TxStatus));
+ dev->name, ioread16(ioaddr + EL3_STATUS), ioread8(ioaddr + TxStatus));
printk(KERN_DEBUG "%s: vortex close stats: rx_nocopy %d rx_copy %d"
" tx_queued %d Rx pre-checksummed %d.\n",
dev->name, vp->rx_nocopy, vp->rx_copy, vp->queued_packet, vp->rx_csumhits);
@@ -2830,18 +2835,18 @@
{
if (vortex_debug > 0) {
struct vortex_private *vp = netdev_priv(dev);
- long ioaddr = dev->base_addr;
+ void __iomem *ioaddr = vp->ioaddr;
if (vp->full_bus_master_tx) {
int i;
- int stalled = inl(ioaddr + PktStatus) & 0x04; /* Possible racy. But it's only debug stuff */
+ int stalled = ioread32(ioaddr + PktStatus) & 0x04; /* Possible racy. But it's only debug stuff */
printk(KERN_ERR " Flags; bus-master %d, dirty %d(%d) current %d(%d)\n",
vp->full_bus_master_tx,
vp->dirty_tx, vp->dirty_tx % TX_RING_SIZE,
vp->cur_tx, vp->cur_tx % TX_RING_SIZE);
printk(KERN_ERR " Transmit list %8.8x vs. %p.\n",
- inl(ioaddr + DownListPtr),
+ ioread32(ioaddr + DownListPtr),
&vp->tx_ring[vp->dirty_tx % TX_RING_SIZE]);
issue_and_wait(dev, DownStall);
for (i = 0; i < TX_RING_SIZE; i++) {
@@ -2855,7 +2860,7 @@
le32_to_cpu(vp->tx_ring[i].status));
}
if (!stalled)
- outw(DownUnstall, ioaddr + EL3_CMD);
+ iowrite16(DownUnstall, ioaddr + EL3_CMD);
}
}
}
@@ -2863,11 +2868,12 @@
static struct net_device_stats *vortex_get_stats(struct net_device *dev)
{
struct vortex_private *vp = netdev_priv(dev);
+ void __iomem *ioaddr = vp->ioaddr;
unsigned long flags;
if (netif_device_present(dev)) { /* AKPM: Used to be netif_running */
spin_lock_irqsave (&vp->lock, flags);
- update_stats(dev->base_addr, dev);
+ update_stats(ioaddr, dev);
spin_unlock_irqrestore (&vp->lock, flags);
}
return &vp->stats;
@@ -2880,37 +2886,37 @@
table. This is done by checking that the ASM (!) code generated uses
atomic updates with '+='.
*/
-static void update_stats(long ioaddr, struct net_device *dev)
+static void update_stats(void __iomem *ioaddr, struct net_device *dev)
{
struct vortex_private *vp = netdev_priv(dev);
- int old_window = inw(ioaddr + EL3_CMD);
+ int old_window = ioread16(ioaddr + EL3_CMD);
if (old_window == 0xffff) /* Chip suspended or ejected. */
return;
/* Unlike the 3c5x9 we need not turn off stats updates while reading. */
/* Switch to the stats window, and read everything. */
EL3WINDOW(6);
- vp->stats.tx_carrier_errors += inb(ioaddr + 0);
- vp->stats.tx_heartbeat_errors += inb(ioaddr + 1);
- vp->stats.collisions += inb(ioaddr + 3);
- vp->stats.tx_window_errors += inb(ioaddr + 4);
- vp->stats.rx_fifo_errors += inb(ioaddr + 5);
- vp->stats.tx_packets += inb(ioaddr + 6);
- vp->stats.tx_packets += (inb(ioaddr + 9)&0x30) << 4;
- /* Rx packets */ inb(ioaddr + 7); /* Must read to clear */
+ vp->stats.tx_carrier_errors += ioread8(ioaddr + 0);
+ vp->stats.tx_heartbeat_errors += ioread8(ioaddr + 1);
+ vp->stats.collisions += ioread8(ioaddr + 3);
+ vp->stats.tx_window_errors += ioread8(ioaddr + 4);
+ vp->stats.rx_fifo_errors += ioread8(ioaddr + 5);
+ vp->stats.tx_packets += ioread8(ioaddr + 6);
+ vp->stats.tx_packets += (ioread8(ioaddr + 9)&0x30) << 4;
+ /* Rx packets */ ioread8(ioaddr + 7); /* Must read to clear */
/* Don't bother with register 9, an extension of registers 6&7.
If we do use the 6&7 values the atomic update assumption above
is invalid. */
- vp->stats.rx_bytes += inw(ioaddr + 10);
- vp->stats.tx_bytes += inw(ioaddr + 12);
+ vp->stats.rx_bytes += ioread16(ioaddr + 10);
+ vp->stats.tx_bytes += ioread16(ioaddr + 12);
/* Extra stats for get_ethtool_stats() */
- vp->xstats.tx_multiple_collisions += inb(ioaddr + 2);
- vp->xstats.tx_deferred += inb(ioaddr + 8);
+ vp->xstats.tx_multiple_collisions += ioread8(ioaddr + 2);
+ vp->xstats.tx_deferred += ioread8(ioaddr + 8);
EL3WINDOW(4);
- vp->xstats.rx_bad_ssd += inb(ioaddr + 12);
+ vp->xstats.rx_bad_ssd += ioread8(ioaddr + 12);
{
- u8 up = inb(ioaddr + 13);
+ u8 up = ioread8(ioaddr + 13);
vp->stats.rx_bytes += (up & 0x0f) << 16;
vp->stats.tx_bytes += (up & 0xf0) << 12;
}
@@ -2922,7 +2928,7 @@
static int vortex_nway_reset(struct net_device *dev)
{
struct vortex_private *vp = netdev_priv(dev);
- long ioaddr = dev->base_addr;
+ void __iomem *ioaddr = vp->ioaddr;
unsigned long flags;
int rc;
@@ -2936,7 +2942,7 @@
static u32 vortex_get_link(struct net_device *dev)
{
struct vortex_private *vp = netdev_priv(dev);
- long ioaddr = dev->base_addr;
+ void __iomem *ioaddr = vp->ioaddr;
unsigned long flags;
int rc;
@@ -2950,7 +2956,7 @@
static int vortex_get_settings(struct net_device *dev, struct ethtool_cmd *cmd)
{
struct vortex_private *vp = netdev_priv(dev);
- long ioaddr = dev->base_addr;
+ void __iomem *ioaddr = vp->ioaddr;
unsigned long flags;
int rc;
@@ -2964,7 +2970,7 @@
static int vortex_set_settings(struct net_device *dev, struct ethtool_cmd *cmd)
{
struct vortex_private *vp = netdev_priv(dev);
- long ioaddr = dev->base_addr;
+ void __iomem *ioaddr = vp->ioaddr;
unsigned long flags;
int rc;
@@ -2994,10 +3000,11 @@
struct ethtool_stats *stats, u64 *data)
{
struct vortex_private *vp = netdev_priv(dev);
+ void __iomem *ioaddr = vp->ioaddr;
unsigned long flags;
spin_lock_irqsave(&vp->lock, flags);
- update_stats(dev->base_addr, dev);
+ update_stats(ioaddr, dev);
spin_unlock_irqrestore(&vp->lock, flags);
data[0] = vp->xstats.tx_deferred;
@@ -3057,7 +3064,7 @@
{
int err;
struct vortex_private *vp = netdev_priv(dev);
- long ioaddr = dev->base_addr;
+ void __iomem *ioaddr = vp->ioaddr;
unsigned long flags;
int state = 0;
@@ -3085,7 +3092,8 @@
the chip has a very clean way to set the mode, unlike many others. */
static void set_rx_mode(struct net_device *dev)
{
- long ioaddr = dev->base_addr;
+ struct vortex_private *vp = netdev_priv(dev);
+ void __iomem *ioaddr = vp->ioaddr;
int new_mode;
if (dev->flags & IFF_PROMISC) {
@@ -3097,7 +3105,7 @@
} else
new_mode = SetRxFilter | RxStation | RxBroadcast;
- outw(new_mode, ioaddr + EL3_CMD);
+ iowrite16(new_mode, ioaddr + EL3_CMD);
}
#if defined(CONFIG_VLAN_8021Q) || defined(CONFIG_VLAN_8021Q_MODULE)
@@ -3111,8 +3119,8 @@
static void set_8021q_mode(struct net_device *dev, int enable)
{
struct vortex_private *vp = netdev_priv(dev);
- long ioaddr = dev->base_addr;
- int old_window = inw(ioaddr + EL3_CMD);
+ void __iomem *ioaddr = vp->ioaddr;
+ int old_window = ioread16(ioaddr + EL3_CMD);
int mac_ctrl;
if ((vp->drv_flags&IS_CYCLONE) || (vp->drv_flags&IS_TORNADO)) {
@@ -3124,24 +3132,24 @@
max_pkt_size += 4; /* 802.1Q VLAN tag */
EL3WINDOW(3);
- outw(max_pkt_size, ioaddr+Wn3_MaxPktSize);
+ iowrite16(max_pkt_size, ioaddr+Wn3_MaxPktSize);
/* set VlanEtherType to let the hardware checksumming
treat tagged frames correctly */
EL3WINDOW(7);
- outw(VLAN_ETHER_TYPE, ioaddr+Wn7_VlanEtherType);
+ iowrite16(VLAN_ETHER_TYPE, ioaddr+Wn7_VlanEtherType);
} else {
/* on older cards we have to enable large frames */
vp->large_frames = dev->mtu > 1500 || enable;
EL3WINDOW(3);
- mac_ctrl = inw(ioaddr+Wn3_MAC_Ctrl);
+ mac_ctrl = ioread16(ioaddr+Wn3_MAC_Ctrl);
if (vp->large_frames)
mac_ctrl |= 0x40;
else
mac_ctrl &= ~0x40;
- outw(mac_ctrl, ioaddr+Wn3_MAC_Ctrl);
+ iowrite16(mac_ctrl, ioaddr+Wn3_MAC_Ctrl);
}
EL3WINDOW(old_window);
@@ -3163,7 +3171,7 @@
/* The maximum data clock rate is 2.5 Mhz. The minimum timing is usually
met by back-to-back PCI I/O cycles, but we insert a delay to avoid
"overclocking" issues. */
-#define mdio_delay() inl(mdio_addr)
+#define mdio_delay() ioread32(mdio_addr)
#define MDIO_SHIFT_CLK 0x01
#define MDIO_DIR_WRITE 0x04
@@ -3174,15 +3182,15 @@
/* Generate the preamble required for initial synchronization and
a few older transceivers. */
-static void mdio_sync(long ioaddr, int bits)
+static void mdio_sync(void __iomem *ioaddr, int bits)
{
- long mdio_addr = ioaddr + Wn4_PhysicalMgmt;
+ void __iomem *mdio_addr = ioaddr + Wn4_PhysicalMgmt;
/* Establish sync by sending at least 32 logic ones. */
while (-- bits >= 0) {
- outw(MDIO_DATA_WRITE1, mdio_addr);
+ iowrite16(MDIO_DATA_WRITE1, mdio_addr);
mdio_delay();
- outw(MDIO_DATA_WRITE1 | MDIO_SHIFT_CLK, mdio_addr);
+ iowrite16(MDIO_DATA_WRITE1 | MDIO_SHIFT_CLK, mdio_addr);
mdio_delay();
}
}
@@ -3190,10 +3198,11 @@
static int mdio_read(struct net_device *dev, int phy_id, int location)
{
int i;
- long ioaddr = dev->base_addr;
+ struct vortex_private *vp = netdev_priv(dev);
+ void __iomem *ioaddr = vp->ioaddr;
int read_cmd = (0xf6 << 10) | (phy_id << 5) | location;
unsigned int retval = 0;
- long mdio_addr = ioaddr + Wn4_PhysicalMgmt;
+ void __iomem *mdio_addr = ioaddr + Wn4_PhysicalMgmt;
if (mii_preamble_required)
mdio_sync(ioaddr, 32);
@@ -3201,17 +3210,17 @@
/* Shift the read command bits out. */
for (i = 14; i >= 0; i--) {
int dataval = (read_cmd&(1<<i)) ? MDIO_DATA_WRITE1 : MDIO_DATA_WRITE0;
- outw(dataval, mdio_addr);
+ iowrite16(dataval, mdio_addr);
mdio_delay();
- outw(dataval | MDIO_SHIFT_CLK, mdio_addr);
+ iowrite16(dataval | MDIO_SHIFT_CLK, mdio_addr);
mdio_delay();
}
/* Read the two transition, 16 data, and wire-idle bits. */
for (i = 19; i > 0; i--) {
- outw(MDIO_ENB_IN, mdio_addr);
+ iowrite16(MDIO_ENB_IN, mdio_addr);
mdio_delay();
- retval = (retval << 1) | ((inw(mdio_addr) & MDIO_DATA_READ) ? 1 : 0);
- outw(MDIO_ENB_IN | MDIO_SHIFT_CLK, mdio_addr);
+ retval = (retval << 1) | ((ioread16(mdio_addr) & MDIO_DATA_READ) ? 1 : 0);
+ iowrite16(MDIO_ENB_IN | MDIO_SHIFT_CLK, mdio_addr);
mdio_delay();
}
return retval & 0x20000 ? 0xffff : retval>>1 & 0xffff;
@@ -3219,9 +3228,10 @@
static void mdio_write(struct net_device *dev, int phy_id, int location, int value)
{
- long ioaddr = dev->base_addr;
+ struct vortex_private *vp = netdev_priv(dev);
+ void __iomem *ioaddr = vp->ioaddr;
int write_cmd = 0x50020000 | (phy_id << 23) | (location << 18) | value;
- long mdio_addr = ioaddr + Wn4_PhysicalMgmt;
+ void __iomem *mdio_addr = ioaddr + Wn4_PhysicalMgmt;
int i;
if (mii_preamble_required)
@@ -3230,16 +3240,16 @@
/* Shift the command bits out. */
for (i = 31; i >= 0; i--) {
int dataval = (write_cmd&(1<<i)) ? MDIO_DATA_WRITE1 : MDIO_DATA_WRITE0;
- outw(dataval, mdio_addr);
+ iowrite16(dataval, mdio_addr);
mdio_delay();
- outw(dataval | MDIO_SHIFT_CLK, mdio_addr);
+ iowrite16(dataval | MDIO_SHIFT_CLK, mdio_addr);
mdio_delay();
}
/* Leave the interface idle. */
for (i = 1; i >= 0; i--) {
- outw(MDIO_ENB_IN, mdio_addr);
+ iowrite16(MDIO_ENB_IN, mdio_addr);
mdio_delay();
- outw(MDIO_ENB_IN | MDIO_SHIFT_CLK, mdio_addr);
+ iowrite16(MDIO_ENB_IN | MDIO_SHIFT_CLK, mdio_addr);
mdio_delay();
}
return;
@@ -3250,15 +3260,15 @@
static void acpi_set_WOL(struct net_device *dev)
{
struct vortex_private *vp = netdev_priv(dev);
- long ioaddr = dev->base_addr;
+ void __iomem *ioaddr = vp->ioaddr;
if (vp->enable_wol) {
/* Power up on: 1==Downloaded Filter, 2==Magic Packets, 4==Link Status. */
EL3WINDOW(7);
- outw(2, ioaddr + 0x0c);
+ iowrite16(2, ioaddr + 0x0c);
/* The RxFilter must accept the WOL frames. */
- outw(SetRxFilter|RxStation|RxMulticast|RxBroadcast, ioaddr + EL3_CMD);
- outw(RxEnable, ioaddr + EL3_CMD);
+ iowrite16(SetRxFilter|RxStation|RxMulticast|RxBroadcast, ioaddr + EL3_CMD);
+ iowrite16(RxEnable, ioaddr + EL3_CMD);
pci_enable_wake(VORTEX_PCI(vp), 0, 1);
@@ -3280,10 +3290,9 @@
vp = netdev_priv(dev);
- /* AKPM: FIXME: we should have
- * if (vp->cb_fn_base) iounmap(vp->cb_fn_base);
- * here
- */
+ if (vp->cb_fn_base)
+ pci_iounmap(VORTEX_PCI(vp), vp->cb_fn_base);
+
unregister_netdev(dev);
if (VORTEX_PCI(vp)) {
@@ -3293,8 +3302,10 @@
pci_disable_device(VORTEX_PCI(vp));
}
/* Should really use issue_and_wait() here */
- outw(TotalReset | ((vp->drv_flags & EEPROM_RESET) ? 0x04 : 0x14),
- dev->base_addr + EL3_CMD);
+ iowrite16(TotalReset | ((vp->drv_flags & EEPROM_RESET) ? 0x04 : 0x14),
+ vp->ioaddr + EL3_CMD);
+
+ pci_iounmap(VORTEX_PCI(vp), vp->ioaddr);
pci_free_consistent(pdev,
sizeof(struct boom_rx_desc) * RX_RING_SIZE
@@ -3342,7 +3353,7 @@
static void __exit vortex_eisa_cleanup (void)
{
struct vortex_private *vp;
- long ioaddr;
+ void __iomem *ioaddr;
#ifdef CONFIG_EISA
/* Take care of the EISA devices */
@@ -3351,11 +3362,13 @@
if (compaq_net_device) {
vp = compaq_net_device->priv;
- ioaddr = compaq_net_device->base_addr;
+ ioaddr = ioport_map(compaq_net_device->base_addr,
+ VORTEX_TOTAL_SIZE);
unregister_netdev (compaq_net_device);
- outw (TotalReset, ioaddr + EL3_CMD);
- release_region (ioaddr, VORTEX_TOTAL_SIZE);
+ iowrite16 (TotalReset, ioaddr + EL3_CMD);
+ release_region(compaq_net_device->base_addr,
+ VORTEX_TOTAL_SIZE);
free_netdev (compaq_net_device);
}