ARM: pxa: rename IRQ_GPIO to PXA_GPIO_TO_IRQ
Avoid potential naming confliction since multiple architecture will be built
in a single kernel.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
diff --git a/arch/arm/mach-pxa/stargate2.c b/arch/arm/mach-pxa/stargate2.c
index 4c9a48b..bbf79d5 100644
--- a/arch/arm/mach-pxa/stargate2.c
+++ b/arch/arm/mach-pxa/stargate2.c
@@ -376,7 +376,7 @@
.bus_num = 1,
.chip_select = 0,
.controller_data = &staccel_chip_info,
- .irq = IRQ_GPIO(96),
+ .irq = PXA_GPIO_TO_IRQ(96),
}, {
.modalias = "cc2420",
.max_speed_hz = 6500000,
@@ -560,18 +560,18 @@
/* Through a nand gate - Also beware, on V2 sensor board the
* pull up resistors are missing.
*/
- .irq = IRQ_GPIO(99),
+ .irq = PXA_GPIO_TO_IRQ(99),
}, { /* ITS400 Sensor board only */
.type = "tsl2561",
.addr = 0x49,
/* Through a nand gate - Also beware, on V2 sensor board the
* pull up resistors are missing.
*/
- .irq = IRQ_GPIO(99),
+ .irq = PXA_GPIO_TO_IRQ(99),
}, { /* ITS400 Sensor board only */
.type = "tmp175",
.addr = 0x4A,
- .irq = IRQ_GPIO(96),
+ .irq = PXA_GPIO_TO_IRQ(96),
}, { /* IMB400 Multimedia board */
.type = "wm8940",
.addr = 0x1A,
@@ -661,8 +661,8 @@
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = IRQ_GPIO(40),
- .end = IRQ_GPIO(40),
+ .start = PXA_GPIO_TO_IRQ(40),
+ .end = PXA_GPIO_TO_IRQ(40),
.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE,
}
};
@@ -707,7 +707,7 @@
}
gpio_direction_input(SG2_GPIO_nSD_DETECT);
- err = request_irq(IRQ_GPIO(SG2_GPIO_nSD_DETECT),
+ err = request_irq(PXA_GPIO_TO_IRQ(SG2_GPIO_nSD_DETECT),
stargate2_detect_int,
IRQ_TYPE_EDGE_BOTH,
"MMC card detect",
@@ -738,7 +738,7 @@
static void stargate2_mci_exit(struct device *dev, void *data)
{
- free_irq(IRQ_GPIO(SG2_GPIO_nSD_DETECT), data);
+ free_irq(PXA_GPIO_TO_IRQ(SG2_GPIO_nSD_DETECT), data);
gpio_free(SG2_SD_POWER_ENABLE);
gpio_free(SG2_GPIO_nSD_DETECT);
}
@@ -938,18 +938,18 @@
/* Through a nand gate - Also beware, on V2 sensor board the
* pull up resistors are missing.
*/
- .irq = IRQ_GPIO(99),
+ .irq = PXA_GPIO_TO_IRQ(99),
}, { /* ITS400 Sensor board only */
.type = "tsl2561",
.addr = 0x49,
/* Through a nand gate - Also beware, on V2 sensor board the
* pull up resistors are missing.
*/
- .irq = IRQ_GPIO(99),
+ .irq = PXA_GPIO_TO_IRQ(99),
}, { /* ITS400 Sensor board only */
.type = "tmp175",
.addr = 0x4A,
- .irq = IRQ_GPIO(96),
+ .irq = PXA_GPIO_TO_IRQ(96),
},
};