[SCSI] aic94xx: plumb in I_T_nexus_reset task management function
Currently aic94xx has no exported I_T_nexus_reset function. This is a
bit of a huge problem, since sas_ata relies on this function to
perform an ATA phy reset and also it means that if abort fails, we
really have no bigger hammer to hit everything with.
Plumb in the I_T_nexus_reset by quiescing the sequencer, sending the
correct phy reset (link for ATA and hard for SAS) and then carefully
resuming the sequencer again.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
diff --git a/drivers/scsi/aic94xx/aic94xx_tmf.c b/drivers/scsi/aic94xx/aic94xx_tmf.c
index 144f5ad..d684c74 100644
--- a/drivers/scsi/aic94xx/aic94xx_tmf.c
+++ b/drivers/scsi/aic94xx/aic94xx_tmf.c
@@ -140,8 +140,14 @@
CLEAR_NEXUS_POST;
}
-#if 0
-static int asd_clear_nexus_I_T(struct domain_device *dev)
+enum clear_nexus_phase {
+ NEXUS_PHASE_PRE,
+ NEXUS_PHASE_POST,
+ NEXUS_PHASE_RESUME,
+};
+
+static int asd_clear_nexus_I_T(struct domain_device *dev,
+ enum clear_nexus_phase phase)
{
struct asd_ha_struct *asd_ha = dev->port->ha->lldd_ha;
struct asd_ascb *ascb;
@@ -150,12 +156,56 @@
CLEAR_NEXUS_PRE;
scb->clear_nexus.nexus = NEXUS_I_T;
- scb->clear_nexus.flags = SEND_Q | EXEC_Q | NOTINQ;
+ switch (phase) {
+ case NEXUS_PHASE_PRE:
+ scb->clear_nexus.flags = EXEC_Q | SUSPEND_TX;
+ break;
+ case NEXUS_PHASE_POST:
+ scb->clear_nexus.flags = SEND_Q | NOTINQ;
+ break;
+ case NEXUS_PHASE_RESUME:
+ scb->clear_nexus.flags = RESUME_TX;
+ }
scb->clear_nexus.conn_handle = cpu_to_le16((u16)(unsigned long)
dev->lldd_dev);
CLEAR_NEXUS_POST;
}
-#endif
+
+int asd_I_T_nexus_reset(struct domain_device *dev)
+{
+ int res, tmp_res, i;
+ struct sas_phy *phy = sas_find_local_phy(dev);
+ /* Standard mandates link reset for ATA (type 0) and
+ * hard reset for SSP (type 1) */
+ int reset_type = (dev->dev_type == SATA_DEV ||
+ (dev->tproto & SAS_PROTOCOL_STP)) ? 0 : 1;
+
+ asd_clear_nexus_I_T(dev, NEXUS_PHASE_PRE);
+ /* send a hard reset */
+ ASD_DPRINTK("sending %s reset to %s\n",
+ reset_type ? "hard" : "soft", phy->dev.bus_id);
+ res = sas_phy_reset(phy, reset_type);
+ if (res == TMF_RESP_FUNC_COMPLETE) {
+ /* wait for the maximum settle time */
+ msleep(500);
+ /* clear all outstanding commands (keep nexus suspended) */
+ asd_clear_nexus_I_T(dev, NEXUS_PHASE_POST);
+ }
+ for (i = 0 ; i < 3; i++) {
+ tmp_res = asd_clear_nexus_I_T(dev, NEXUS_PHASE_RESUME);
+ if (tmp_res == TC_RESUME)
+ return res;
+ msleep(500);
+ }
+
+ /* This is a bit of a problem: the sequencer is still suspended
+ * and is refusing to resume. Hope it will resume on a bigger hammer
+ * or the disk is lost */
+ dev_printk(KERN_ERR, &phy->dev,
+ "Failed to resume nexus after reset 0x%x\n", tmp_res);
+
+ return TMF_RESP_FUNC_FAILED;
+}
static int asd_clear_nexus_I_T_L(struct domain_device *dev, u8 *lun)
{