mxc_nand: do not depend on disabling the irq in the interrupt handler
This patch reverts the driver to enabling/disabling the NFC interrupt
mask rather than enabling/disabling the system interrupt. This cleans
up the driver so that it doesn't rely on interrupts being disabled
within the interrupt handler.
For i.MX21 we keep the current behaviour, that is calling
enable_irq/disable_irq_nosync to enable/disable interrupts. This patch
is based on earlier work by John Ogness.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: John Ogness <john.ogness@linutronix.de>
Tested-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
diff --git a/drivers/mtd/nand/mxc_nand.c b/drivers/mtd/nand/mxc_nand.c
index b2828e8..214b03a 100644
--- a/drivers/mtd/nand/mxc_nand.c
+++ b/drivers/mtd/nand/mxc_nand.c
@@ -30,6 +30,8 @@
#include <linux/clk.h>
#include <linux/err.h>
#include <linux/io.h>
+#include <linux/irq.h>
+#include <linux/completion.h>
#include <asm/mach/flash.h>
#include <mach/mxc_nand.h>
@@ -151,7 +153,7 @@
int irq;
int eccsize;
- wait_queue_head_t irq_waitq;
+ struct completion op_completion;
uint8_t *data_buf;
unsigned int buf_start;
@@ -164,6 +166,7 @@
void (*send_read_id)(struct mxc_nand_host *);
uint16_t (*get_dev_status)(struct mxc_nand_host *);
int (*check_int)(struct mxc_nand_host *);
+ void (*irq_control)(struct mxc_nand_host *, int);
};
/* OOB placement block for use with hardware ecc generation */
@@ -216,9 +219,12 @@
{
struct mxc_nand_host *host = dev_id;
- disable_irq_nosync(irq);
+ if (!host->check_int(host))
+ return IRQ_NONE;
- wake_up(&host->irq_waitq);
+ host->irq_control(host, 0);
+
+ complete(&host->op_completion);
return IRQ_HANDLED;
}
@@ -245,11 +251,54 @@
if (!(tmp & NFC_V1_V2_CONFIG2_INT))
return 0;
- writew(tmp & ~NFC_V1_V2_CONFIG2_INT, NFC_V1_V2_CONFIG2);
+ if (!cpu_is_mx21())
+ writew(tmp & ~NFC_V1_V2_CONFIG2_INT, NFC_V1_V2_CONFIG2);
return 1;
}
+/*
+ * It has been observed that the i.MX21 cannot read the CONFIG2:INT bit
+ * if interrupts are masked (CONFIG1:INT_MSK is set). To handle this, the
+ * driver can enable/disable the irq line rather than simply masking the
+ * interrupts.
+ */
+static void irq_control_mx21(struct mxc_nand_host *host, int activate)
+{
+ if (activate)
+ enable_irq(host->irq);
+ else
+ disable_irq_nosync(host->irq);
+}
+
+static void irq_control_v1_v2(struct mxc_nand_host *host, int activate)
+{
+ uint16_t tmp;
+
+ tmp = readw(NFC_V1_V2_CONFIG1);
+
+ if (activate)
+ tmp &= ~NFC_V1_V2_CONFIG1_INT_MSK;
+ else
+ tmp |= NFC_V1_V2_CONFIG1_INT_MSK;
+
+ writew(tmp, NFC_V1_V2_CONFIG1);
+}
+
+static void irq_control_v3(struct mxc_nand_host *host, int activate)
+{
+ uint32_t tmp;
+
+ tmp = readl(NFC_V3_CONFIG2);
+
+ if (activate)
+ tmp &= ~NFC_V3_CONFIG2_INT_MSK;
+ else
+ tmp |= NFC_V3_CONFIG2_INT_MSK;
+
+ writel(tmp, NFC_V3_CONFIG2);
+}
+
/* This function polls the NANDFC to wait for the basic operation to
* complete by checking the INT bit of config2 register.
*/
@@ -259,10 +308,9 @@
if (useirq) {
if (!host->check_int(host)) {
-
- enable_irq(host->irq);
-
- wait_event(host->irq_waitq, host->check_int(host));
+ INIT_COMPLETION(host->op_completion);
+ host->irq_control(host, 1);
+ wait_for_completion(&host->op_completion);
}
} else {
while (max_retries-- > 0) {
@@ -799,6 +847,7 @@
NFC_V3_CONFIG2_2CMD_PHASES |
NFC_V3_CONFIG2_SPAS(mtd->oobsize >> 1) |
NFC_V3_CONFIG2_ST_CMD(0x70) |
+ NFC_V3_CONFIG2_INT_MSK |
NFC_V3_CONFIG2_NUM_ADDR_PHASE0;
if (chip->ecc.mode == NAND_ECC_HW)
@@ -1024,6 +1073,10 @@
host->send_read_id = send_read_id_v1_v2;
host->get_dev_status = get_dev_status_v1_v2;
host->check_int = check_int_v1_v2;
+ if (cpu_is_mx21())
+ host->irq_control = irq_control_mx21;
+ else
+ host->irq_control = irq_control_v1_v2;
}
if (nfc_is_v21()) {
@@ -1062,6 +1115,7 @@
host->send_read_id = send_read_id_v3;
host->check_int = check_int_v3;
host->get_dev_status = get_dev_status_v3;
+ host->irq_control = irq_control_v3;
oob_smallpage = &nandv2_hw_eccoob_smallpage;
oob_largepage = &nandv2_hw_eccoob_largepage;
} else
@@ -1093,14 +1147,34 @@
this->options |= NAND_USE_FLASH_BBT;
}
- init_waitqueue_head(&host->irq_waitq);
+ init_completion(&host->op_completion);
host->irq = platform_get_irq(pdev, 0);
+ /*
+ * mask the interrupt. For i.MX21 explicitely call
+ * irq_control_v1_v2 to use the mask bit. We can't call
+ * disable_irq_nosync() for an interrupt we do not own yet.
+ */
+ if (cpu_is_mx21())
+ irq_control_v1_v2(host, 0);
+ else
+ host->irq_control(host, 0);
+
err = request_irq(host->irq, mxc_nfc_irq, IRQF_DISABLED, DRIVER_NAME, host);
if (err)
goto eirq;
+ host->irq_control(host, 0);
+
+ /*
+ * Now that the interrupt is disabled make sure the interrupt
+ * mask bit is cleared on i.MX21. Otherwise we can't read
+ * the interrupt status bit on this machine.
+ */
+ if (cpu_is_mx21())
+ irq_control_v1_v2(host, 1);
+
/* first scan to find the device and get the page size */
if (nand_scan_ident(mtd, 1, NULL)) {
err = -ENXIO;