| menuconfig EXTCON |
| tristate "External Connector Class (extcon) support" |
| help |
| Say Y here to enable external connector class (extcon) support. |
| This allows monitoring external connectors by userspace |
| via sysfs and uevent and supports external connectors with |
| multiple states; i.e., an extcon that may have multiple |
| cables attached. For example, an external connector of a device |
| may be used to connect an HDMI cable and a AC adaptor, and to |
| host USB ports. Many of 30-pin connectors including PDMI are |
| also good examples. |
| |
| if EXTCON |
| |
| comment "Extcon Device Drivers" |
| |
| config EXTCON_ADC_JACK |
| tristate "ADC Jack extcon support" |
| depends on IIO |
| help |
| Say Y here to enable extcon device driver based on ADC values. |
| |
| config EXTCON_ARIZONA |
| tristate "Wolfson Arizona EXTCON support" |
| depends on MFD_ARIZONA && INPUT && SND_SOC |
| help |
| Say Y here to enable support for external accessory detection |
| with Wolfson Arizona devices. These are audio CODECs with |
| advanced audio accessory detection support. |
| |
| config EXTCON_AXP288 |
| tristate "X-Power AXP288 EXTCON support" |
| depends on MFD_AXP20X && USB_PHY |
| help |
| Say Y here to enable support for USB peripheral detection |
| and USB MUX switching by X-Power AXP288 PMIC. |
| |
| config EXTCON_GPIO |
| tristate "GPIO extcon support" |
| depends on GPIOLIB || COMPILE_TEST |
| help |
| Say Y here to enable GPIO based extcon support. Note that GPIO |
| extcon supports single state per extcon instance. |
| |
| config EXTCON_MAX14577 |
| tristate "Maxim MAX14577/77836 EXTCON Support" |
| depends on MFD_MAX14577 |
| select IRQ_DOMAIN |
| select REGMAP_I2C |
| help |
| If you say yes here you get support for the MUIC device of |
| Maxim MAX14577/77836. The MAX14577/77836 MUIC is a USB port accessory |
| detector and switch. |
| |
| config EXTCON_MAX77693 |
| tristate "Maxim MAX77693 EXTCON Support" |
| depends on MFD_MAX77693 && INPUT |
| select IRQ_DOMAIN |
| select REGMAP_I2C |
| help |
| If you say yes here you get support for the MUIC device of |
| Maxim MAX77693 PMIC. The MAX77693 MUIC is a USB port accessory |
| detector and switch. |
| |
| config EXTCON_MAX77843 |
| tristate "Maxim MAX77843 EXTCON Support" |
| depends on MFD_MAX77843 |
| select IRQ_DOMAIN |
| select REGMAP_I2C |
| help |
| If you say yes here you get support for the MUIC device of |
| Maxim MAX77843. The MAX77843 MUIC is a USB port accessory |
| detector add switch. |
| |
| config EXTCON_MAX8997 |
| tristate "Maxim MAX8997 EXTCON Support" |
| depends on MFD_MAX8997 && IRQ_DOMAIN |
| help |
| If you say yes here you get support for the MUIC device of |
| Maxim MAX8997 PMIC. The MAX8997 MUIC is a USB port accessory |
| detector and switch. |
| |
| config EXTCON_PALMAS |
| tristate "Palmas USB EXTCON support" |
| depends on MFD_PALMAS |
| help |
| Say Y here to enable support for USB peripheral and USB host |
| detection by palmas usb. |
| |
| config EXTCON_RT8973A |
| tristate "Richtek RT8973A EXTCON support" |
| depends on I2C |
| select IRQ_DOMAIN |
| select REGMAP_I2C |
| select REGMAP_IRQ |
| help |
| If you say yes here you get support for the MUIC device of |
| Richtek RT8973A. The RT8973A is a USB port accessory detector |
| and switch that is optimized to protect low voltage system |
| from abnormal high input voltage (up to 28V). |
| |
| config EXTCON_SM5502 |
| tristate "Silicon Mitus SM5502 EXTCON support" |
| depends on I2C |
| select IRQ_DOMAIN |
| select REGMAP_I2C |
| select REGMAP_IRQ |
| help |
| If you say yes here you get support for the MUIC device of |
| Silicon Mitus SM5502. The SM5502 is a USB port accessory |
| detector and switch. |
| |
| config EXTCON_USB_GPIO |
| tristate "USB GPIO extcon support" |
| depends on GPIOLIB || COMPILE_TEST |
| help |
| Say Y here to enable GPIO based USB cable detection extcon support. |
| Used typically if GPIO is used for USB ID pin detection. |
| |
| endif |