3c50x: convert printk() to pr_<foo>()
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
diff --git a/drivers/net/3c503.c b/drivers/net/3c503.c
index 4f08bd9..134638a 100644
--- a/drivers/net/3c503.c
+++ b/drivers/net/3c503.c
@@ -234,16 +234,16 @@
}
if (ei_debug && version_printed++ == 0)
- printk(version);
+ pr_debug("%s", version);
dev->base_addr = ioaddr;
- printk("%s: 3c503 at i/o base %#3x, node ", dev->name, ioaddr);
+ pr_info("%s: 3c503 at i/o base %#3x, node ", dev->name, ioaddr);
/* Retrieve and print the ethernet address. */
for (i = 0; i < 6; i++)
dev->dev_addr[i] = inb(ioaddr + i);
- printk("%pM", dev->dev_addr);
+ pr_cont("%pM", dev->dev_addr);
/* Map the 8390 back into the window. */
outb(ECNTRL_THIN, ioaddr + 0x406);
@@ -256,7 +256,8 @@
outb_p(E8390_PAGE0, ioaddr + E8390_CMD);
/* Probe for, turn on and clear the board's shared memory. */
- if (ei_debug > 2) printk(" memory jumpers %2.2x ", membase_reg);
+ if (ei_debug > 2)
+ pr_cont(" memory jumpers %2.2x ", membase_reg);
outb(EGACFR_NORM, ioaddr + 0x405); /* Enable RAM */
/* This should be probed for (or set via an ioctl()) at run-time.
@@ -268,7 +269,7 @@
#else
ei_status.interface_num = dev->mem_end & 0xf;
#endif
- printk(", using %sternal xcvr.\n", ei_status.interface_num == 0 ? "in" : "ex");
+ pr_cont(", using %sternal xcvr.\n", ei_status.interface_num == 0 ? "in" : "ex");
if ((membase_reg & 0xf0) == 0) {
dev->mem_start = 0;
@@ -292,7 +293,7 @@
writel(test_val, mem_base + i);
if (readl(mem_base) != 0xba5eba5e
|| readl(mem_base + i) != test_val) {
- printk("3c503: memory failure or memory address conflict.\n");
+ pr_warning("3c503: memory failure or memory address conflict.\n");
dev->mem_start = 0;
ei_status.name = "3c503-PIO";
iounmap(mem_base);
@@ -344,7 +345,7 @@
if (dev->irq == 2)
dev->irq = 9;
else if (dev->irq > 5 && dev->irq != 9) {
- printk("3c503: configured interrupt %d invalid, will use autoIRQ.\n",
+ pr_warning("3c503: configured interrupt %d invalid, will use autoIRQ.\n",
dev->irq);
dev->irq = 0;
}
@@ -359,7 +360,7 @@
goto out1;
if (dev->mem_start)
- printk("%s: %s - %dkB RAM, 8kB shared mem window at %#6lx-%#6lx.\n",
+ pr_info("%s: %s - %dkB RAM, 8kB shared mem window at %#6lx-%#6lx.\n",
dev->name, ei_status.name, (wordlength+1)<<3,
dev->mem_start, dev->mem_end-1);
@@ -367,7 +368,7 @@
{
ei_status.tx_start_page = EL2_MB1_START_PG;
ei_status.rx_start_page = EL2_MB1_START_PG + TX_PAGES;
- printk("\n%s: %s, %dkB RAM, using programmed I/O (REJUMPER for SHARED MEMORY).\n",
+ pr_info("%s: %s, %dkB RAM, using programmed I/O (REJUMPER for SHARED MEMORY).\n",
dev->name, ei_status.name, (wordlength+1)<<3);
}
release_region(ioaddr + 0x400, 8);
@@ -435,15 +436,16 @@
el2_reset_8390(struct net_device *dev)
{
if (ei_debug > 1) {
- printk("%s: Resetting the 3c503 board...", dev->name);
- printk("%#lx=%#02x %#lx=%#02x %#lx=%#02x...", E33G_IDCFR, inb(E33G_IDCFR),
+ pr_debug("%s: Resetting the 3c503 board...", dev->name);
+ pr_cont(" %#lx=%#02x %#lx=%#02x %#lx=%#02x...", E33G_IDCFR, inb(E33G_IDCFR),
E33G_CNTRL, inb(E33G_CNTRL), E33G_GACFR, inb(E33G_GACFR));
}
outb_p(ECNTRL_RESET|ECNTRL_THIN, E33G_CNTRL);
ei_status.txing = 0;
outb_p(ei_status.interface_num==0 ? ECNTRL_THIN : ECNTRL_AUI, E33G_CNTRL);
el2_init_card(dev);
- if (ei_debug > 1) printk("done\n");
+ if (ei_debug > 1)
+ pr_cont("done\n");
}
/* Initialize the 3c503 GA registers after a reset. */
@@ -529,7 +531,7 @@
{
if(!boguscount--)
{
- printk("%s: FIFO blocked in el2_block_output.\n", dev->name);
+ pr_notice("%s: FIFO blocked in el2_block_output.\n", dev->name);
el2_reset_8390(dev);
goto blocked;
}
@@ -581,7 +583,7 @@
{
if(!boguscount--)
{
- printk("%s: FIFO blocked in el2_get_8390_hdr.\n", dev->name);
+ pr_notice("%s: FIFO blocked in el2_get_8390_hdr.\n", dev->name);
memset(hdr, 0x00, sizeof(struct e8390_pkt_hdr));
el2_reset_8390(dev);
goto blocked;
@@ -645,7 +647,7 @@
{
if(!boguscount--)
{
- printk("%s: FIFO blocked in el2_block_input.\n", dev->name);
+ pr_notice("%s: FIFO blocked in el2_block_input.\n", dev->name);
el2_reset_8390(dev);
goto blocked;
}
@@ -707,7 +709,7 @@
for (this_dev = 0; this_dev < MAX_EL2_CARDS; this_dev++) {
if (io[this_dev] == 0) {
if (this_dev != 0) break; /* only autoprobe 1st one */
- printk(KERN_NOTICE "3c503.c: Presently autoprobing (not recommended) for a single card.\n");
+ pr_notice("3c503.c: Presently autoprobing (not recommended) for a single card.\n");
}
dev = alloc_eip_netdev();
if (!dev)
@@ -720,7 +722,7 @@
continue;
}
free_netdev(dev);
- printk(KERN_WARNING "3c503.c: No 3c503 card found (i/o = 0x%x).\n", io[this_dev]);
+ pr_warning("3c503.c: No 3c503 card found (i/o = 0x%x).\n", io[this_dev]);
break;
}
if (found)