usb: plusb: Add support for PL-25A1
This patch adds support for the PL-25A1 by adding the appropriate
USB ID's. This chip is used in the Belkin 'Windows Easy Transfer'
Cables.
Signed-off-by: Simon Wood <simon@mungewell.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
diff --git a/drivers/net/usb/Kconfig b/drivers/net/usb/Kconfig
index 3ec22c3..9d4f911 100644
--- a/drivers/net/usb/Kconfig
+++ b/drivers/net/usb/Kconfig
@@ -258,7 +258,7 @@
optionally with LEDs that indicate traffic
config USB_NET_PLUSB
- tristate "Prolific PL-2301/2302 based cables"
+ tristate "Prolific PL-2301/2302/25A1 based cables"
# if the handshake/init/reset problems, from original 'plusb',
# are ever resolved ... then remove "experimental"
depends on USB_USBNET && EXPERIMENTAL
diff --git a/drivers/net/usb/plusb.c b/drivers/net/usb/plusb.c
index 2fe1bb5..f46aa07 100644
--- a/drivers/net/usb/plusb.c
+++ b/drivers/net/usb/plusb.c
@@ -45,6 +45,14 @@
* seems to get wedged under load. Prolific docs are weak, and
* don't identify differences between PL2301 and PL2302, much less
* anything to explain the different PL2302 versions observed.
+ *
+ * NOTE: pl2501 has several modes, including pl2301 and pl2302
+ * compatibility. Some docs suggest the difference between 2301
+ * and 2302 is only to make MS-Windows use a different driver...
+ *
+ * pl25a1 glue based on patch from Tony Gibbs. Prolific "docs" on
+ * this chip are as usual incomplete about what control messages
+ * are supported.
*/
/*
@@ -95,7 +103,7 @@
}
static const struct driver_info prolific_info = {
- .description = "Prolific PL-2301/PL-2302",
+ .description = "Prolific PL-2301/PL-2302/PL-25A1",
.flags = FLAG_POINTTOPOINT | FLAG_NO_SETINT,
/* some PL-2302 versions seem to fail usb_set_interface() */
.reset = pl_reset,
@@ -111,6 +119,7 @@
static const struct usb_device_id products [] = {
+/* full speed cables */
{
USB_DEVICE(0x067b, 0x0000), // PL-2301
.driver_info = (unsigned long) &prolific_info,
@@ -119,6 +128,15 @@
.driver_info = (unsigned long) &prolific_info,
},
+/* high speed cables */
+{
+ USB_DEVICE(0x067b, 0x25a1), /* PL-25A1, no eeprom */
+ .driver_info = (unsigned long) &prolific_info,
+}, {
+ USB_DEVICE(0x050d, 0x258a), /* Belkin F5U258/F5U279 (PL-25A1) */
+ .driver_info = (unsigned long) &prolific_info,
+},
+
{ }, // END
};
MODULE_DEVICE_TABLE(usb, products);
@@ -145,5 +163,5 @@
module_exit(plusb_exit);
MODULE_AUTHOR("David Brownell");
-MODULE_DESCRIPTION("Prolific PL-2301/2302 USB Host to Host Link Driver");
+MODULE_DESCRIPTION("Prolific PL-2301/2302/25A1 USB Host to Host Link Driver");
MODULE_LICENSE("GPL");