MIPS: Alchemy: Basic support for the DB1300 board.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2867/
Patchwork: https://patchwork.linux-mips.org/patch/2919/
Patchwork: https://patchwork.linux-mips.org/patch/2928/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
diff --git a/arch/mips/alchemy/Kconfig b/arch/mips/alchemy/Kconfig
index 766bada..f9a13be 100644
--- a/arch/mips/alchemy/Kconfig
+++ b/arch/mips/alchemy/Kconfig
@@ -49,6 +49,14 @@
select SYS_SUPPORTS_LITTLE_ENDIAN
select SYS_HAS_EARLY_PRINTK
+config MIPS_DB1300
+ bool "NetLogic DB1300 board"
+ select ALCHEMY_GPIOINT_AU1300
+ select DMA_COHERENT
+ select MIPS_DISABLE_OBSOLETE_IDE
+ select SYS_SUPPORTS_LITTLE_ENDIAN
+ select SYS_HAS_EARLY_PRINTK
+
config MIPS_DB1500
bool "Alchemy DB1500 board"
select ALCHEMY_GPIOINT_AU1000
diff --git a/arch/mips/alchemy/Platform b/arch/mips/alchemy/Platform
index 2920af9..4d13e21 100644
--- a/arch/mips/alchemy/Platform
+++ b/arch/mips/alchemy/Platform
@@ -68,6 +68,13 @@
load-$(CONFIG_MIPS_DB1200) += 0xffffffff80100000
#
+# NetLogic DBAu1300 development platform
+#
+platform-$(CONFIG_MIPS_DB1300) += alchemy/devboards/
+cflags-$(CONFIG_MIPS_DB1300) += -I$(srctree)/arch/mips/include/asm/mach-db1x00
+load-$(CONFIG_MIPS_DB1300) += 0xffffffff80100000
+
+#
# 4G-Systems eval board
#
platform-$(CONFIG_MIPS_MTX1) += alchemy/mtx-1/
diff --git a/arch/mips/alchemy/devboards/Makefile b/arch/mips/alchemy/devboards/Makefile
index 5afaf94..2eb75c9 100644
--- a/arch/mips/alchemy/devboards/Makefile
+++ b/arch/mips/alchemy/devboards/Makefile
@@ -11,5 +11,6 @@
obj-$(CONFIG_MIPS_DB1000) += db1x00/
obj-$(CONFIG_MIPS_DB1100) += db1x00/
obj-$(CONFIG_MIPS_DB1200) += db1200/
+obj-$(CONFIG_MIPS_DB1300) += db1300.o
obj-$(CONFIG_MIPS_DB1500) += db1x00/
obj-$(CONFIG_MIPS_DB1550) += db1x00/
diff --git a/arch/mips/alchemy/devboards/db1300.c b/arch/mips/alchemy/devboards/db1300.c
new file mode 100644
index 0000000..c41788c5
--- /dev/null
+++ b/arch/mips/alchemy/devboards/db1300.c
@@ -0,0 +1,787 @@
+/*
+ * DBAu1300 init and platform device setup.
+ *
+ * (c) 2009 Manuel Lauss <manuel.lauss@googlemail.com>
+ */
+
+#include <linux/dma-mapping.h>
+#include <linux/gpio.h>
+#include <linux/gpio_keys.h>
+#include <linux/init.h>
+#include <linux/input.h> /* KEY_* codes */
+#include <linux/i2c.h>
+#include <linux/io.h>
+#include <linux/leds.h>
+#include <linux/ata_platform.h>
+#include <linux/mmc/host.h>
+#include <linux/module.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/nand.h>
+#include <linux/mtd/partitions.h>
+#include <linux/platform_device.h>
+#include <linux/smsc911x.h>
+
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-au1x00/au1100_mmc.h>
+#include <asm/mach-au1x00/au1xxx_dbdma.h>
+#include <asm/mach-au1x00/au1xxx_psc.h>
+#include <asm/mach-db1x00/db1300.h>
+#include <asm/mach-db1x00/bcsr.h>
+#include <asm/mach-au1x00/prom.h>
+
+#include "platform.h"
+
+static struct i2c_board_info db1300_i2c_devs[] __initdata = {
+ { I2C_BOARD_INFO("wm8731", 0x1b), }, /* I2S audio codec */
+ { I2C_BOARD_INFO("ne1619", 0x2d), }, /* adm1025-compat hwmon */
+};
+
+/* multifunction pins to assign to GPIO controller */
+static int db1300_gpio_pins[] __initdata = {
+ AU1300_PIN_LCDPWM0, AU1300_PIN_PSC2SYNC1, AU1300_PIN_WAKE1,
+ AU1300_PIN_WAKE2, AU1300_PIN_WAKE3, AU1300_PIN_FG3AUX,
+ AU1300_PIN_EXTCLK1,
+ -1, /* terminator */
+};
+
+/* multifunction pins to assign to device functions */
+static int db1300_dev_pins[] __initdata = {
+ /* wake-from-str pins 0-3 */
+ AU1300_PIN_WAKE0,
+ /* external clock sources for PSC0 */
+ AU1300_PIN_EXTCLK0,
+ /* 8bit MMC interface on SD0: 6-9 */
+ AU1300_PIN_SD0DAT4, AU1300_PIN_SD0DAT5, AU1300_PIN_SD0DAT6,
+ AU1300_PIN_SD0DAT7,
+ /* UART1 pins: 11-18 */
+ AU1300_PIN_U1RI, AU1300_PIN_U1DCD, AU1300_PIN_U1DSR,
+ AU1300_PIN_U1CTS, AU1300_PIN_U1RTS, AU1300_PIN_U1DTR,
+ AU1300_PIN_U1RX, AU1300_PIN_U1TX,
+ /* UART0 pins: 19-24 */
+ AU1300_PIN_U0RI, AU1300_PIN_U0DCD, AU1300_PIN_U0DSR,
+ AU1300_PIN_U0CTS, AU1300_PIN_U0RTS, AU1300_PIN_U0DTR,
+ /* UART2: 25-26 */
+ AU1300_PIN_U2RX, AU1300_PIN_U2TX,
+ /* UART3: 27-28 */
+ AU1300_PIN_U3RX, AU1300_PIN_U3TX,
+ /* LCD controller PWMs, ext pixclock: 30-31 */
+ AU1300_PIN_LCDPWM1, AU1300_PIN_LCDCLKIN,
+ /* SD1 interface: 32-37 */
+ AU1300_PIN_SD1DAT0, AU1300_PIN_SD1DAT1, AU1300_PIN_SD1DAT2,
+ AU1300_PIN_SD1DAT3, AU1300_PIN_SD1CMD, AU1300_PIN_SD1CLK,
+ /* SD2 interface: 38-43 */
+ AU1300_PIN_SD2DAT0, AU1300_PIN_SD2DAT1, AU1300_PIN_SD2DAT2,
+ AU1300_PIN_SD2DAT3, AU1300_PIN_SD2CMD, AU1300_PIN_SD2CLK,
+ /* PSC0/1 clocks: 44-45 */
+ AU1300_PIN_PSC0CLK, AU1300_PIN_PSC1CLK,
+ /* PSCs: 46-49/50-53/54-57/58-61 */
+ AU1300_PIN_PSC0SYNC0, AU1300_PIN_PSC0SYNC1, AU1300_PIN_PSC0D0,
+ AU1300_PIN_PSC0D1,
+ AU1300_PIN_PSC1SYNC0, AU1300_PIN_PSC1SYNC1, AU1300_PIN_PSC1D0,
+ AU1300_PIN_PSC1D1,
+ AU1300_PIN_PSC2SYNC0, AU1300_PIN_PSC2D0,
+ AU1300_PIN_PSC2D1,
+ AU1300_PIN_PSC3SYNC0, AU1300_PIN_PSC3SYNC1, AU1300_PIN_PSC3D0,
+ AU1300_PIN_PSC3D1,
+ /* PCMCIA interface: 62-70 */
+ AU1300_PIN_PCE2, AU1300_PIN_PCE1, AU1300_PIN_PIOS16,
+ AU1300_PIN_PIOR, AU1300_PIN_PWE, AU1300_PIN_PWAIT,
+ AU1300_PIN_PREG, AU1300_PIN_POE, AU1300_PIN_PIOW,
+ /* camera interface H/V sync inputs: 71-72 */
+ AU1300_PIN_CIMLS, AU1300_PIN_CIMFS,
+ /* PSC2/3 clocks: 73-74 */
+ AU1300_PIN_PSC2CLK, AU1300_PIN_PSC3CLK,
+ -1, /* terminator */
+};
+
+static void __init db1300_gpio_config(void)
+{
+ int *i;
+
+ i = &db1300_dev_pins[0];
+ while (*i != -1)
+ au1300_pinfunc_to_dev(*i++);
+
+ i = &db1300_gpio_pins[0];
+ while (*i != -1)
+ au1300_gpio_direction_input(*i++);/* implies pin_to_gpio */
+
+ au1300_set_dbdma_gpio(1, AU1300_PIN_FG3AUX);
+}
+
+char *get_system_type(void)
+{
+ return "DB1300";
+}
+
+/**********************************************************************/
+
+static void au1300_nand_cmd_ctrl(struct mtd_info *mtd, int cmd,
+ unsigned int ctrl)
+{
+ struct nand_chip *this = mtd->priv;
+ unsigned long ioaddr = (unsigned long)this->IO_ADDR_W;
+
+ ioaddr &= 0xffffff00;
+
+ if (ctrl & NAND_CLE) {
+ ioaddr += MEM_STNAND_CMD;
+ } else if (ctrl & NAND_ALE) {
+ ioaddr += MEM_STNAND_ADDR;
+ } else {
+ /* assume we want to r/w real data by default */
+ ioaddr += MEM_STNAND_DATA;
+ }
+ this->IO_ADDR_R = this->IO_ADDR_W = (void __iomem *)ioaddr;
+ if (cmd != NAND_CMD_NONE) {
+ __raw_writeb(cmd, this->IO_ADDR_W);
+ wmb();
+ }
+}
+
+static int au1300_nand_device_ready(struct mtd_info *mtd)
+{
+ return __raw_readl((void __iomem *)MEM_STSTAT) & 1;
+}
+
+static const char *db1300_part_probes[] = { "cmdlinepart", NULL };
+
+static struct mtd_partition db1300_nand_parts[] = {
+ {
+ .name = "NAND FS 0",
+ .offset = 0,
+ .size = 8 * 1024 * 1024,
+ },
+ {
+ .name = "NAND FS 1",
+ .offset = MTDPART_OFS_APPEND,
+ .size = MTDPART_SIZ_FULL
+ },
+};
+
+struct platform_nand_data db1300_nand_platdata = {
+ .chip = {
+ .nr_chips = 1,
+ .chip_offset = 0,
+ .nr_partitions = ARRAY_SIZE(db1300_nand_parts),
+ .partitions = db1300_nand_parts,
+ .chip_delay = 20,
+ .part_probe_types = db1300_part_probes,
+ },
+ .ctrl = {
+ .dev_ready = au1300_nand_device_ready,
+ .cmd_ctrl = au1300_nand_cmd_ctrl,
+ },
+};
+
+static struct resource db1300_nand_res[] = {
+ [0] = {
+ .start = DB1300_NAND_PHYS_ADDR,
+ .end = DB1300_NAND_PHYS_ADDR + 0xff,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+static struct platform_device db1300_nand_dev = {
+ .name = "gen_nand",
+ .num_resources = ARRAY_SIZE(db1300_nand_res),
+ .resource = db1300_nand_res,
+ .id = -1,
+ .dev = {
+ .platform_data = &db1300_nand_platdata,
+ }
+};
+
+/**********************************************************************/
+
+static struct resource db1300_eth_res[] = {
+ [0] = {
+ .start = DB1300_ETH_PHYS_ADDR,
+ .end = DB1300_ETH_PHYS_END,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = DB1300_ETH_INT,
+ .end = DB1300_ETH_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct smsc911x_platform_config db1300_eth_config = {
+ .phy_interface = PHY_INTERFACE_MODE_MII,
+ .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
+ .irq_type = SMSC911X_IRQ_TYPE_PUSH_PULL,
+ .flags = SMSC911X_USE_32BIT,
+};
+
+static struct platform_device db1300_eth_dev = {
+ .name = "smsc911x",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(db1300_eth_res),
+ .resource = db1300_eth_res,
+ .dev = {
+ .platform_data = &db1300_eth_config,
+ },
+};
+
+/**********************************************************************/
+
+static struct resource au1300_psc1_res[] = {
+ [0] = {
+ .start = AU1300_PSC1_PHYS_ADDR,
+ .end = AU1300_PSC1_PHYS_ADDR + 0x0fff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AU1300_PSC1_INT,
+ .end = AU1300_PSC1_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+ [2] = {
+ .start = AU1300_DSCR_CMD0_PSC1_TX,
+ .end = AU1300_DSCR_CMD0_PSC1_TX,
+ .flags = IORESOURCE_DMA,
+ },
+ [3] = {
+ .start = AU1300_DSCR_CMD0_PSC1_RX,
+ .end = AU1300_DSCR_CMD0_PSC1_RX,
+ .flags = IORESOURCE_DMA,
+ },
+};
+
+static struct platform_device db1300_ac97_dev = {
+ .name = "au1xpsc_ac97",
+ .id = 1, /* PSC ID. match with AC97 codec ID! */
+ .num_resources = ARRAY_SIZE(au1300_psc1_res),
+ .resource = au1300_psc1_res,
+};
+
+/**********************************************************************/
+
+static struct resource au1300_psc2_res[] = {
+ [0] = {
+ .start = AU1300_PSC2_PHYS_ADDR,
+ .end = AU1300_PSC2_PHYS_ADDR + 0x0fff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AU1300_PSC2_INT,
+ .end = AU1300_PSC2_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+ [2] = {
+ .start = AU1300_DSCR_CMD0_PSC2_TX,
+ .end = AU1300_DSCR_CMD0_PSC2_TX,
+ .flags = IORESOURCE_DMA,
+ },
+ [3] = {
+ .start = AU1300_DSCR_CMD0_PSC2_RX,
+ .end = AU1300_DSCR_CMD0_PSC2_RX,
+ .flags = IORESOURCE_DMA,
+ },
+};
+
+static struct platform_device db1300_i2s_dev = {
+ .name = "au1xpsc_i2s",
+ .id = 2, /* PSC ID */
+ .num_resources = ARRAY_SIZE(au1300_psc2_res),
+ .resource = au1300_psc2_res,
+};
+
+/**********************************************************************/
+
+static struct resource au1300_psc3_res[] = {
+ [0] = {
+ .start = AU1300_PSC3_PHYS_ADDR,
+ .end = AU1300_PSC3_PHYS_ADDR + 0x0fff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AU1300_PSC3_INT,
+ .end = AU1300_PSC3_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+ [2] = {
+ .start = AU1300_DSCR_CMD0_PSC3_TX,
+ .end = AU1300_DSCR_CMD0_PSC3_TX,
+ .flags = IORESOURCE_DMA,
+ },
+ [3] = {
+ .start = AU1300_DSCR_CMD0_PSC3_RX,
+ .end = AU1300_DSCR_CMD0_PSC3_RX,
+ .flags = IORESOURCE_DMA,
+ },
+};
+
+static struct platform_device db1300_i2c_dev = {
+ .name = "au1xpsc_smbus",
+ .id = 0, /* bus number */
+ .num_resources = ARRAY_SIZE(au1300_psc3_res),
+ .resource = au1300_psc3_res,
+};
+
+/**********************************************************************/
+
+/* proper key assignments when facing the LCD panel. For key assignments
+ * according to the schematics swap up with down and left with right.
+ * I chose to use it to emulate the arrow keys of a keyboard.
+ */
+static struct gpio_keys_button db1300_5waysw_arrowkeys[] = {
+ {
+ .code = KEY_DOWN,
+ .gpio = AU1300_PIN_LCDPWM0,
+ .type = EV_KEY,
+ .debounce_interval = 1,
+ .active_low = 1,
+ .desc = "5waysw-down",
+ },
+ {
+ .code = KEY_UP,
+ .gpio = AU1300_PIN_PSC2SYNC1,
+ .type = EV_KEY,
+ .debounce_interval = 1,
+ .active_low = 1,
+ .desc = "5waysw-up",
+ },
+ {
+ .code = KEY_RIGHT,
+ .gpio = AU1300_PIN_WAKE3,
+ .type = EV_KEY,
+ .debounce_interval = 1,
+ .active_low = 1,
+ .desc = "5waysw-right",
+ },
+ {
+ .code = KEY_LEFT,
+ .gpio = AU1300_PIN_WAKE2,
+ .type = EV_KEY,
+ .debounce_interval = 1,
+ .active_low = 1,
+ .desc = "5waysw-left",
+ },
+ {
+ .code = KEY_ENTER,
+ .gpio = AU1300_PIN_WAKE1,
+ .type = EV_KEY,
+ .debounce_interval = 1,
+ .active_low = 1,
+ .desc = "5waysw-push",
+ },
+};
+
+static struct gpio_keys_platform_data db1300_5waysw_data = {
+ .buttons = db1300_5waysw_arrowkeys,
+ .nbuttons = ARRAY_SIZE(db1300_5waysw_arrowkeys),
+ .rep = 1,
+ .name = "db1300-5wayswitch",
+};
+
+static struct platform_device db1300_5waysw_dev = {
+ .name = "gpio-keys",
+ .dev = {
+ .platform_data = &db1300_5waysw_data,
+ },
+};
+
+/**********************************************************************/
+
+static struct platform_device db1300_rtc_dev = {
+ .name = "rtc-au1xxx",
+ .id = -1,
+};
+
+/**********************************************************************/
+
+static struct pata_platform_info db1300_ide_info = {
+ .ioport_shift = DB1300_IDE_REG_SHIFT,
+};
+
+#define IDE_ALT_START (14 << DB1300_IDE_REG_SHIFT)
+static struct resource db1300_ide_res[] = {
+ [0] = {
+ .start = DB1300_IDE_PHYS_ADDR,
+ .end = DB1300_IDE_PHYS_ADDR + IDE_ALT_START - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = DB1300_IDE_PHYS_ADDR + IDE_ALT_START,
+ .end = DB1300_IDE_PHYS_ADDR + DB1300_IDE_PHYS_LEN - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [2] = {
+ .start = DB1300_IDE_INT,
+ .end = DB1300_IDE_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device db1300_ide_dev = {
+ .dev = {
+ .platform_data = &db1300_ide_info,
+ },
+ .name = "pata_platform",
+ .resource = db1300_ide_res,
+ .num_resources = ARRAY_SIZE(db1300_ide_res),
+};
+
+/**********************************************************************/
+
+static irqreturn_t db1300_mmc_cd(int irq, void *ptr)
+{
+ void(*mmc_cd)(struct mmc_host *, unsigned long);
+
+ /* disable the one currently screaming. No other way to shut it up */
+ if (irq == DB1300_SD1_INSERT_INT) {
+ disable_irq_nosync(DB1300_SD1_INSERT_INT);
+ enable_irq(DB1300_SD1_EJECT_INT);
+ } else {
+ disable_irq_nosync(DB1300_SD1_EJECT_INT);
+ enable_irq(DB1300_SD1_INSERT_INT);
+ }
+
+ /* link against CONFIG_MMC=m. We can only be called once MMC core has
+ * initialized the controller, so symbol_get() should always succeed.
+ */
+ mmc_cd = symbol_get(mmc_detect_change);
+ mmc_cd(ptr, msecs_to_jiffies(500));
+ symbol_put(mmc_detect_change);
+
+ return IRQ_HANDLED;
+}
+
+static int db1300_mmc_card_readonly(void *mmc_host)
+{
+ /* it uses SD1 interface, but the DB1200's SD0 bit in the CPLD */
+ return bcsr_read(BCSR_STATUS) & BCSR_STATUS_SD0WP;
+}
+
+static int db1300_mmc_card_inserted(void *mmc_host)
+{
+ return bcsr_read(BCSR_SIGSTAT) & (1 << 12); /* insertion irq signal */
+}
+
+static int db1300_mmc_cd_setup(void *mmc_host, int en)
+{
+ int ret;
+
+ if (en) {
+ ret = request_irq(DB1300_SD1_INSERT_INT, db1300_mmc_cd, 0,
+ "sd_insert", mmc_host);
+ if (ret)
+ goto out;
+
+ ret = request_irq(DB1300_SD1_EJECT_INT, db1300_mmc_cd, 0,
+ "sd_eject", mmc_host);
+ if (ret) {
+ free_irq(DB1300_SD1_INSERT_INT, mmc_host);
+ goto out;
+ }
+
+ if (db1300_mmc_card_inserted(mmc_host))
+ enable_irq(DB1300_SD1_EJECT_INT);
+ else
+ enable_irq(DB1300_SD1_INSERT_INT);
+
+ } else {
+ free_irq(DB1300_SD1_INSERT_INT, mmc_host);
+ free_irq(DB1300_SD1_EJECT_INT, mmc_host);
+ }
+ ret = 0;
+out:
+ return ret;
+}
+
+static void db1300_mmcled_set(struct led_classdev *led,
+ enum led_brightness brightness)
+{
+ if (brightness != LED_OFF)
+ bcsr_mod(BCSR_LEDS, BCSR_LEDS_LED0, 0);
+ else
+ bcsr_mod(BCSR_LEDS, 0, BCSR_LEDS_LED0);
+}
+
+static struct led_classdev db1300_mmc_led = {
+ .brightness_set = db1300_mmcled_set,
+};
+
+struct au1xmmc_platform_data db1300_sd1_platdata = {
+ .cd_setup = db1300_mmc_cd_setup,
+ .card_inserted = db1300_mmc_card_inserted,
+ .card_readonly = db1300_mmc_card_readonly,
+ .led = &db1300_mmc_led,
+};
+
+static struct resource au1300_sd1_res[] = {
+ [0] = {
+ .start = AU1300_SD1_PHYS_ADDR,
+ .end = AU1300_SD1_PHYS_ADDR,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AU1300_SD1_INT,
+ .end = AU1300_SD1_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+ [2] = {
+ .start = AU1300_DSCR_CMD0_SDMS_TX1,
+ .end = AU1300_DSCR_CMD0_SDMS_TX1,
+ .flags = IORESOURCE_DMA,
+ },
+ [3] = {
+ .start = AU1300_DSCR_CMD0_SDMS_RX1,
+ .end = AU1300_DSCR_CMD0_SDMS_RX1,
+ .flags = IORESOURCE_DMA,
+ },
+};
+
+static struct platform_device db1300_sd1_dev = {
+ .dev = {
+ .platform_data = &db1300_sd1_platdata,
+ },
+ .name = "au1xxx-mmc",
+ .id = 1,
+ .resource = au1300_sd1_res,
+ .num_resources = ARRAY_SIZE(au1300_sd1_res),
+};
+
+/**********************************************************************/
+
+static int db1300_movinand_inserted(void *mmc_host)
+{
+ return 0; /* disable for now, it doesn't work yet */
+}
+
+static int db1300_movinand_readonly(void *mmc_host)
+{
+ return 0;
+}
+
+static void db1300_movinand_led_set(struct led_classdev *led,
+ enum led_brightness brightness)
+{
+ if (brightness != LED_OFF)
+ bcsr_mod(BCSR_LEDS, BCSR_LEDS_LED1, 0);
+ else
+ bcsr_mod(BCSR_LEDS, 0, BCSR_LEDS_LED1);
+}
+
+static struct led_classdev db1300_movinand_led = {
+ .brightness_set = db1300_movinand_led_set,
+};
+
+struct au1xmmc_platform_data db1300_sd0_platdata = {
+ .card_inserted = db1300_movinand_inserted,
+ .card_readonly = db1300_movinand_readonly,
+ .led = &db1300_movinand_led,
+ .mask_host_caps = MMC_CAP_NEEDS_POLL,
+};
+
+static struct resource au1300_sd0_res[] = {
+ [0] = {
+ .start = AU1100_SD0_PHYS_ADDR,
+ .end = AU1100_SD0_PHYS_ADDR,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AU1300_SD0_INT,
+ .end = AU1300_SD0_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+ [2] = {
+ .start = AU1300_DSCR_CMD0_SDMS_TX0,
+ .end = AU1300_DSCR_CMD0_SDMS_TX0,
+ .flags = IORESOURCE_DMA,
+ },
+ [3] = {
+ .start = AU1300_DSCR_CMD0_SDMS_RX0,
+ .end = AU1300_DSCR_CMD0_SDMS_RX0,
+ .flags = IORESOURCE_DMA,
+ },
+};
+
+static struct platform_device db1300_sd0_dev = {
+ .dev = {
+ .platform_data = &db1300_sd0_platdata,
+ },
+ .name = "au1xxx-mmc",
+ .id = 0,
+ .resource = au1300_sd0_res,
+ .num_resources = ARRAY_SIZE(au1300_sd0_res),
+};
+
+/**********************************************************************/
+
+static struct platform_device db1300_wm9715_dev = {
+ .name = "wm9712-codec",
+ .id = 1, /* ID of PSC for AC97 audio, see asoc glue! */
+};
+
+static struct platform_device db1300_ac97dma_dev = {
+ .name = "au1xpsc-pcm",
+ .id = 1, /* PSC ID */
+};
+
+static struct platform_device db1300_i2sdma_dev = {
+ .name = "au1xpsc-pcm",
+ .id = 2, /* PSC ID */
+};
+
+static struct platform_device db1300_sndac97_dev = {
+ .name = "db1300-ac97",
+};
+
+static struct platform_device db1300_sndi2s_dev = {
+ .name = "db1300-i2s",
+};
+
+/**********************************************************************/
+
+static struct resource au1300_lcd_res[] = {
+ [0] = {
+ .start = AU1200_LCD_PHYS_ADDR,
+ .end = AU1200_LCD_PHYS_ADDR + 0x800 - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AU1300_LCD_INT,
+ .end = AU1300_LCD_INT,
+ .flags = IORESOURCE_IRQ,
+ }
+};
+
+static u64 au1300_lcd_dmamask = DMA_BIT_MASK(32);
+
+static struct platform_device db1300_lcd_dev = {
+ .name = "au1200-lcd",
+ .id = 0,
+ .dev = {
+ .dma_mask = &au1300_lcd_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ },
+ .num_resources = ARRAY_SIZE(au1300_lcd_res),
+ .resource = au1300_lcd_res,
+};
+
+/**********************************************************************/
+
+static struct platform_device *db1300_dev[] __initdata = {
+ &db1300_eth_dev,
+ &db1300_i2c_dev,
+ &db1300_5waysw_dev,
+ &db1300_rtc_dev,
+ &db1300_nand_dev,
+ &db1300_ide_dev,
+ &db1300_sd0_dev,
+ &db1300_sd1_dev,
+ &db1300_lcd_dev,
+ &db1300_ac97_dev,
+ &db1300_i2s_dev,
+ &db1300_wm9715_dev,
+ &db1300_ac97dma_dev,
+ &db1300_i2sdma_dev,
+ &db1300_sndac97_dev,
+ &db1300_sndi2s_dev,
+};
+
+static int __init db1300_device_init(void)
+{
+ int swapped, cpldirq;
+
+ /* setup CPLD IRQ muxer */
+ cpldirq = au1300_gpio_to_irq(AU1300_PIN_EXTCLK1);
+ irq_set_irq_type(cpldirq, IRQ_TYPE_LEVEL_HIGH);
+ bcsr_init_irq(DB1300_FIRST_INT, DB1300_LAST_INT, cpldirq);
+
+ /* insert/eject IRQs: one always triggers so don't enable them
+ * when doing request_irq() on them. DB1200 has this bug too.
+ */
+ irq_set_status_flags(DB1300_SD1_INSERT_INT, IRQ_NOAUTOEN);
+ irq_set_status_flags(DB1300_SD1_EJECT_INT, IRQ_NOAUTOEN);
+ irq_set_status_flags(DB1300_CF_INSERT_INT, IRQ_NOAUTOEN);
+ irq_set_status_flags(DB1300_CF_EJECT_INT, IRQ_NOAUTOEN);
+
+ /*
+ * setup board
+ */
+ prom_get_ethernet_addr(&db1300_eth_config.mac[0]);
+
+ i2c_register_board_info(0, db1300_i2c_devs,
+ ARRAY_SIZE(db1300_i2c_devs));
+
+ /* Audio PSC clock is supplied by codecs (PSC1, 2) */
+ __raw_writel(PSC_SEL_CLK_SERCLK,
+ (void __iomem *)KSEG1ADDR(AU1300_PSC1_PHYS_ADDR) + PSC_SEL_OFFSET);
+ wmb();
+ __raw_writel(PSC_SEL_CLK_SERCLK,
+ (void __iomem *)KSEG1ADDR(AU1300_PSC2_PHYS_ADDR) + PSC_SEL_OFFSET);
+ wmb();
+ /* I2C uses internal 48MHz EXTCLK1 */
+ __raw_writel(PSC_SEL_CLK_INTCLK,
+ (void __iomem *)KSEG1ADDR(AU1300_PSC3_PHYS_ADDR) + PSC_SEL_OFFSET);
+ wmb();
+
+ /* enable power to USB ports */
+ bcsr_mod(BCSR_RESETS, 0, BCSR_RESETS_USBHPWR | BCSR_RESETS_OTGPWR);
+
+ /* although it is socket #0, it uses the CPLD bits which previous boards
+ * have used for socket #1.
+ */
+ db1x_register_pcmcia_socket(
+ AU1000_PCMCIA_ATTR_PHYS_ADDR,
+ AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x00400000 - 1,
+ AU1000_PCMCIA_MEM_PHYS_ADDR,
+ AU1000_PCMCIA_MEM_PHYS_ADDR + 0x00400000 - 1,
+ AU1000_PCMCIA_IO_PHYS_ADDR,
+ AU1000_PCMCIA_IO_PHYS_ADDR + 0x00010000 - 1,
+ DB1300_CF_INT, DB1300_CF_INSERT_INT, 0, DB1300_CF_EJECT_INT, 1);
+
+ swapped = bcsr_read(BCSR_STATUS) & BCSR_STATUS_DB1200_SWAPBOOT;
+ db1x_register_norflash(64 << 20, 2, swapped);
+
+ return platform_add_devices(db1300_dev, ARRAY_SIZE(db1300_dev));
+}
+device_initcall(db1300_device_init);
+
+
+void __init board_setup(void)
+{
+ unsigned short whoami;
+
+ db1300_gpio_config();
+ bcsr_init(DB1300_BCSR_PHYS_ADDR,
+ DB1300_BCSR_PHYS_ADDR + DB1300_BCSR_HEXLED_OFS);
+
+ whoami = bcsr_read(BCSR_WHOAMI);
+ printk(KERN_INFO "NetLogic DBAu1300 Development Platform.\n\t"
+ "BoardID %d CPLD Rev %d DaughtercardID %d\n",
+ BCSR_WHOAMI_BOARD(whoami), BCSR_WHOAMI_CPLD(whoami),
+ BCSR_WHOAMI_DCID(whoami));
+
+ /* enable UARTs, YAMON only enables #2 */
+ alchemy_uart_enable(AU1300_UART0_PHYS_ADDR);
+ alchemy_uart_enable(AU1300_UART1_PHYS_ADDR);
+ alchemy_uart_enable(AU1300_UART3_PHYS_ADDR);
+}
+
+
+/* au1200fb calls these: STERBT EINEN TRAGISCHEN TOD!!! */
+int board_au1200fb_panel(void)
+{
+ return 9; /* DB1300_800x480 */
+}
+
+int board_au1200fb_panel_init(void)
+{
+ /* Apply power (Vee/Vdd logic is inverted on Panel DB1300_800x480) */
+ bcsr_mod(BCSR_BOARD, BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD,
+ BCSR_BOARD_LCDBL);
+ return 0;
+}
+
+int board_au1200fb_panel_shutdown(void)
+{
+ /* Remove power (Vee/Vdd logic is inverted on Panel DB1300_800x480) */
+ bcsr_mod(BCSR_BOARD, BCSR_BOARD_LCDBL,
+ BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD);
+ return 0;
+}
diff --git a/arch/mips/alchemy/devboards/prom.c b/arch/mips/alchemy/devboards/prom.c
index f734833..3a73f96 100644
--- a/arch/mips/alchemy/devboards/prom.c
+++ b/arch/mips/alchemy/devboards/prom.c
@@ -61,5 +61,9 @@
void prom_putchar(unsigned char c)
{
+#ifdef CONFIG_MIPS_DB1300
+ alchemy_uart_putchar(AU1300_UART2_PHYS_ADDR, c);
+#else
alchemy_uart_putchar(AU1000_UART0_PHYS_ADDR, c);
+#endif
}
diff --git a/arch/mips/boot/compressed/uart-alchemy.c b/arch/mips/boot/compressed/uart-alchemy.c
index eb063e6..3112df8 100644
--- a/arch/mips/boot/compressed/uart-alchemy.c
+++ b/arch/mips/boot/compressed/uart-alchemy.c
@@ -2,6 +2,9 @@
void putc(char c)
{
- /* all current (Jan. 2010) in-kernel boards */
+#ifdef CONFIG_MIPS_DB1300
+ alchemy_uart_putchar(AU1300_UART2_PHYS_ADDR, c);
+#else
alchemy_uart_putchar(AU1000_UART0_PHYS_ADDR, c);
+#endif
}
diff --git a/arch/mips/configs/db1300_defconfig b/arch/mips/configs/db1300_defconfig
new file mode 100644
index 0000000..c38b190
--- /dev/null
+++ b/arch/mips/configs/db1300_defconfig
@@ -0,0 +1,391 @@
+CONFIG_MIPS=y
+CONFIG_MIPS_ALCHEMY=y
+CONFIG_ALCHEMY_GPIOINT_AU1300=y
+CONFIG_MIPS_DB1300=y
+CONFIG_SOC_AU1300=y
+CONFIG_RWSEM_GENERIC_SPINLOCK=y
+CONFIG_ARCH_SUPPORTS_OPROFILE=y
+CONFIG_GENERIC_HWEIGHT=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_GENERIC_CMOS_UPDATE=y
+CONFIG_SCHED_OMIT_FRAME_POINTER=y
+CONFIG_CEVT_R4K_LIB=y
+CONFIG_CSRC_R4K_LIB=y
+CONFIG_DMA_COHERENT=y
+CONFIG_SYS_HAS_EARLY_PRINTK=y
+CONFIG_MIPS_DISABLE_OBSOLETE_IDE=y
+CONFIG_GENERIC_GPIO=y
+CONFIG_CPU_LITTLE_ENDIAN=y
+CONFIG_SYS_SUPPORTS_APM_EMULATION=y
+CONFIG_SYS_SUPPORTS_LITTLE_ENDIAN=y
+CONFIG_IRQ_CPU=y
+CONFIG_MIPS_L1_CACHE_SHIFT=5
+CONFIG_CPU_MIPS32_R1=y
+CONFIG_SYS_SUPPORTS_ZBOOT=y
+CONFIG_SYS_HAS_CPU_MIPS32_R1=y
+CONFIG_CPU_MIPS32=y
+CONFIG_CPU_MIPSR1=y
+CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y
+CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y
+CONFIG_HARDWARE_WATCHPOINTS=y
+CONFIG_32BIT=y
+CONFIG_PAGE_SIZE_4KB=y
+CONFIG_FORCE_MAX_ZONEORDER=11
+CONFIG_CPU_HAS_PREFETCH=y
+CONFIG_MIPS_MT_DISABLED=y
+CONFIG_64BIT_PHYS_ADDR=y
+CONFIG_ARCH_PHYS_ADDR_T_64BIT=y
+CONFIG_CPU_HAS_SYNC=y
+CONFIG_CPU_SUPPORTS_HIGHMEM=y
+CONFIG_ARCH_FLATMEM_ENABLE=y
+CONFIG_ARCH_POPULATES_NODE_MAP=y
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+CONFIG_PAGEFLAGS_EXTENDED=y
+CONFIG_SPLIT_PTLOCK_CPUS=4
+CONFIG_COMPACTION=y
+CONFIG_MIGRATION=y
+CONFIG_PHYS_ADDR_T_64BIT=y
+CONFIG_ZONE_DMA_FLAG=0
+CONFIG_VIRT_TO_BUS=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
+CONFIG_NEED_PER_CPU_KM=y
+CONFIG_TICK_ONESHOT=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
+CONFIG_HZ_100=y
+CONFIG_SYS_SUPPORTS_ARBIT_HZ=y
+CONFIG_HZ=100
+CONFIG_PREEMPT_NONE=y
+CONFIG_LOCKDEP_SUPPORT=y
+CONFIG_STACKTRACE_SUPPORT=y
+CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
+CONFIG_HAVE_IRQ_WORK=y
+CONFIG_EXPERIMENTAL=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+CONFIG_CROSS_COMPILE=""
+CONFIG_LOCALVERSION="-db1300"
+CONFIG_LOCALVERSION_AUTO=y
+CONFIG_HAVE_KERNEL_GZIP=y
+CONFIG_HAVE_KERNEL_BZIP2=y
+CONFIG_HAVE_KERNEL_LZMA=y
+CONFIG_HAVE_KERNEL_LZO=y
+CONFIG_KERNEL_LZMA=y
+CONFIG_SWAP=y
+CONFIG_SYSVIPC=y
+CONFIG_SYSVIPC_SYSCTL=y
+CONFIG_POSIX_MQUEUE=y
+CONFIG_POSIX_MQUEUE_SYSCTL=y
+CONFIG_FHANDLE=y
+CONFIG_HAVE_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_GENERIC_IRQ_SHOW=y
+CONFIG_TINY_RCU=y
+CONFIG_LOG_BUF_SHIFT=19
+CONFIG_NAMESPACES=y
+CONFIG_UTS_NS=y
+CONFIG_IPC_NS=y
+CONFIG_USER_NS=y
+CONFIG_PID_NS=y
+CONFIG_NET_NS=y
+CONFIG_SYSCTL=y
+CONFIG_ANON_INODES=y
+CONFIG_EXPERT=y
+CONFIG_SYSCTL_SYSCALL=y
+CONFIG_KALLSYMS=y
+CONFIG_KALLSYMS_ALL=y
+CONFIG_HOTPLUG=y
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+CONFIG_ELF_CORE=y
+CONFIG_BASE_FULL=y
+CONFIG_FUTEX=y
+CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_TIMERFD=y
+CONFIG_EVENTFD=y
+CONFIG_SHMEM=y
+CONFIG_AIO=y
+CONFIG_EMBEDDED=y
+CONFIG_HAVE_PERF_EVENTS=y
+CONFIG_PERF_USE_VMALLOC=y
+CONFIG_SLAB=y
+CONFIG_HAVE_OPROFILE=y
+CONFIG_HAVE_KPROBES=y
+CONFIG_HAVE_KRETPROBES=y
+CONFIG_HAVE_DMA_ATTRS=y
+CONFIG_HAVE_DMA_API_DEBUG=y
+CONFIG_HAVE_ARCH_JUMP_LABEL=y
+CONFIG_HAVE_GENERIC_DMA_COHERENT=y
+CONFIG_SLABINFO=y
+CONFIG_RT_MUTEXES=y
+CONFIG_BASE_SMALL=0
+CONFIG_BLOCK=y
+CONFIG_LBDAF=y
+CONFIG_BLK_DEV_BSG=y
+CONFIG_IOSCHED_NOOP=y
+CONFIG_DEFAULT_NOOP=y
+CONFIG_DEFAULT_IOSCHED="noop"
+CONFIG_INLINE_SPIN_UNLOCK=y
+CONFIG_INLINE_SPIN_UNLOCK_IRQ=y
+CONFIG_INLINE_READ_UNLOCK=y
+CONFIG_INLINE_READ_UNLOCK_IRQ=y
+CONFIG_INLINE_WRITE_UNLOCK=y
+CONFIG_INLINE_WRITE_UNLOCK_IRQ=y
+CONFIG_MMU=y
+CONFIG_PCCARD=y
+CONFIG_PCMCIA=y
+CONFIG_PCMCIA_LOAD_CIS=y
+CONFIG_PCMCIA_ALCHEMY_DEVBOARD=y
+CONFIG_BINFMT_ELF=y
+CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS=y
+CONFIG_TRAD_SIGNALS=y
+CONFIG_ARCH_HIBERNATION_POSSIBLE=y
+CONFIG_ARCH_SUSPEND_POSSIBLE=y
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_XFRM=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+CONFIG_IP_PNP_RARP=y
+CONFIG_INET_TUNNEL=y
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+CONFIG_IPV6=y
+CONFIG_INET6_XFRM_MODE_TRANSPORT=y
+CONFIG_INET6_XFRM_MODE_TUNNEL=y
+CONFIG_INET6_XFRM_MODE_BEET=y
+CONFIG_IPV6_SIT=y
+CONFIG_IPV6_NDISC_NODETYPE=y
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_STANDALONE=y
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+CONFIG_FW_LOADER=y
+CONFIG_FIRMWARE_IN_KERNEL=y
+CONFIG_EXTRA_FIRMWARE=""
+CONFIG_MTD=y
+CONFIG_MTD_CMDLINE_PARTS=y
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLKDEVS=y
+CONFIG_MTD_BLOCK=y
+CONFIG_MTD_CFI=y
+CONFIG_MTD_GEN_PROBE=y
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+CONFIG_MTD_CFI_AMDSTD=y
+CONFIG_MTD_CFI_UTIL=y
+CONFIG_MTD_PHYSMAP=y
+CONFIG_MTD_NAND_ECC=y
+CONFIG_MTD_NAND=y
+CONFIG_MTD_NAND_IDS=y
+CONFIG_MTD_NAND_PLATFORM=y
+CONFIG_BLK_DEV=y
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_BLK_DEV_UB=y
+CONFIG_HAVE_IDE=y
+CONFIG_IDE=y
+CONFIG_IDE_GD=y
+CONFIG_IDE_GD_ATA=y
+CONFIG_BLK_DEV_IDECS=y
+CONFIG_IDE_TASK_IOCTL=y
+CONFIG_IDE_PROC_FS=y
+CONFIG_BLK_DEV_PLATFORM=y
+CONFIG_SCSI_MOD=y
+CONFIG_NETDEVICES=y
+CONFIG_MII=y
+CONFIG_PHYLIB=y
+CONFIG_SMSC_PHY=y
+CONFIG_NET_ETHERNET=y
+CONFIG_SMSC911X=y
+CONFIG_INPUT=y
+CONFIG_INPUT_EVDEV=y
+CONFIG_INPUT_KEYBOARD=y
+CONFIG_KEYBOARD_GPIO=y
+CONFIG_INPUT_TOUCHSCREEN=y
+CONFIG_TOUCHSCREEN_WM97XX=y
+CONFIG_TOUCHSCREEN_WM9712=y
+CONFIG_TOUCHSCREEN_WM9713=y
+CONFIG_INPUT_MISC=y
+CONFIG_INPUT_UINPUT=y
+CONFIG_VT=y
+CONFIG_CONSOLE_TRANSLATIONS=y
+CONFIG_VT_CONSOLE=y
+CONFIG_HW_CONSOLE=y
+CONFIG_VT_HW_CONSOLE_BINDING=y
+CONFIG_UNIX98_PTYS=y
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_NR_UARTS=4
+CONFIG_SERIAL_8250_RUNTIME_UARTS=4
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+CONFIG_I2C=y
+CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_SMBUS=y
+CONFIG_I2C_AU1550=y
+CONFIG_SPI=y
+CONFIG_SPI_MASTER=y
+CONFIG_SPI_AU1550=y
+CONFIG_SPI_BITBANG=y
+CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
+CONFIG_HWMON=y
+CONFIG_HWMON_VID=y
+CONFIG_SENSORS_ADM1025=y
+CONFIG_FB=y
+CONFIG_FB_AU1200=y
+CONFIG_DUMMY_CONSOLE=y
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_FONTS=y
+CONFIG_FONT_ACORN_8x8=y
+CONFIG_LOGO=y
+CONFIG_LOGO_LINUX_CLUT224=y
+CONFIG_SOUND=y
+CONFIG_SND=y
+CONFIG_SND_TIMER=y
+CONFIG_SND_PCM=y
+CONFIG_SND_JACK=y
+CONFIG_SND_HRTIMER=y
+CONFIG_SND_DYNAMIC_MINORS=y
+CONFIG_SND_VERBOSE_PROCFS=y
+CONFIG_SND_VERBOSE_PRINTK=y
+CONFIG_SND_VMASTER=y
+CONFIG_SND_AC97_CODEC=y
+CONFIG_SND_SOC=y
+CONFIG_SND_SOC_CACHE_LZO=y
+CONFIG_SND_SOC_AC97_BUS=y
+CONFIG_SND_SOC_AU1XPSC=y
+CONFIG_SND_SOC_AU1XPSC_I2S=y
+CONFIG_SND_SOC_AU1XPSC_AC97=y
+CONFIG_SND_SOC_DB1300=y
+CONFIG_SND_SOC_I2C_AND_SPI=y
+CONFIG_SND_SOC_WM8731=y
+CONFIG_SND_SOC_WM9712=y
+CONFIG_AC97_BUS=y
+CONFIG_HID_SUPPORT=y
+CONFIG_HID=y
+CONFIG_HIDRAW=y
+CONFIG_USB_HID=y
+CONFIG_USB_HIDDEV=y
+CONFIG_USB_SUPPORT=y
+CONFIG_USB_ARCH_HAS_HCD=y
+CONFIG_USB_ARCH_HAS_OHCI=y
+CONFIG_USB_ARCH_HAS_EHCI=y
+CONFIG_USB=y
+CONFIG_USB_DYNAMIC_MINORS=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_EHCI_ROOT_HUB_TT=y
+CONFIG_USB_EHCI_TT_NEWSCHED=y
+CONFIG_USB_OHCI_HCD=y
+CONFIG_USB_OHCI_LITTLE_ENDIAN=y
+CONFIG_RTC_LIB=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_HCTOSYS=y
+CONFIG_RTC_HCTOSYS_DEVICE="rtc0"
+CONFIG_RTC_INTF_SYSFS=y
+CONFIG_RTC_INTF_PROC=y
+CONFIG_RTC_INTF_DEV=y
+CONFIG_RTC_INTF_DEV_UIE_EMUL=y
+CONFIG_RTC_DRV_AU1XXX=y
+CONFIG_EXT2_FS=y
+CONFIG_FS_POSIX_ACL=y
+CONFIG_EXPORTFS=y
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
+CONFIG_DNOTIFY=y
+CONFIG_INOTIFY_USER=y
+CONFIG_GENERIC_ACL=y
+CONFIG_FAT_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_FAT_DEFAULT_CODEPAGE=437
+CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
+CONFIG_PROC_FS=y
+CONFIG_PROC_SYSCTL=y
+CONFIG_PROC_PAGE_MONITOR=y
+CONFIG_SYSFS=y
+CONFIG_TMPFS=y
+CONFIG_TMPFS_POSIX_ACL=y
+CONFIG_TMPFS_XATTR=y
+CONFIG_MISC_FILESYSTEMS=y
+CONFIG_JFFS2_FS=y
+CONFIG_JFFS2_FS_DEBUG=0
+CONFIG_JFFS2_FS_WRITEBUFFER=y
+CONFIG_JFFS2_SUMMARY=y
+CONFIG_JFFS2_FS_XATTR=y
+CONFIG_JFFS2_FS_POSIX_ACL=y
+CONFIG_JFFS2_FS_SECURITY=y
+CONFIG_JFFS2_COMPRESSION_OPTIONS=y
+CONFIG_JFFS2_ZLIB=y
+CONFIG_JFFS2_LZO=y
+CONFIG_JFFS2_RTIME=y
+CONFIG_JFFS2_RUBIN=y
+CONFIG_JFFS2_CMODE_PRIORITY=y
+CONFIG_SQUASHFS=y
+CONFIG_SQUASHFS_XZ=y
+CONFIG_SQUASHFS_FRAGMENT_CACHE_SIZE=3
+CONFIG_NETWORK_FILESYSTEMS=y
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3=y
+CONFIG_ROOT_NFS=y
+CONFIG_LOCKD=y
+CONFIG_LOCKD_V4=y
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=y
+CONFIG_MSDOS_PARTITION=y
+CONFIG_NLS=y
+CONFIG_NLS_DEFAULT="iso8859-1"
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_CODEPAGE_850=y
+CONFIG_NLS_ASCII=y
+CONFIG_NLS_ISO8859_1=y
+CONFIG_NLS_ISO8859_15=y
+CONFIG_NLS_UTF8=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
+CONFIG_PRINTK_TIME=y
+CONFIG_DEFAULT_MESSAGE_LOGLEVEL=4
+CONFIG_ENABLE_WARN_DEPRECATED=y
+CONFIG_ENABLE_MUST_CHECK=y
+CONFIG_FRAME_WARN=1024
+CONFIG_MAGIC_SYSRQ=y
+CONFIG_STRIP_ASM_SYMS=y
+CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
+CONFIG_HAVE_DYNAMIC_FTRACE=y
+CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_C_RECORDMCOUNT=y
+CONFIG_TRACING_SUPPORT=y
+CONFIG_HAVE_ARCH_KGDB=y
+CONFIG_EARLY_PRINTK=y
+CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE="video=au1200fb:panel:bs console=tty console=ttyS2,115200"
+CONFIG_DEBUG_ZBOOT=y
+CONFIG_DEFAULT_SECURITY_DAC=y
+CONFIG_DEFAULT_SECURITY=""
+CONFIG_CRYPTO=y
+CONFIG_BITREVERSE=y
+CONFIG_CRC32=y
+CONFIG_ZLIB_INFLATE=y
+CONFIG_ZLIB_DEFLATE=y
+CONFIG_LZO_COMPRESS=y
+CONFIG_LZO_DECOMPRESS=y
+CONFIG_XZ_DEC=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
+CONFIG_NLATTR=y
+CONFIG_GENERIC_ATOMIC64=y
diff --git a/arch/mips/include/asm/mach-db1x00/bcsr.h b/arch/mips/include/asm/mach-db1x00/bcsr.h
index 618d2de..0ef6300 100644
--- a/arch/mips/include/asm/mach-db1x00/bcsr.h
+++ b/arch/mips/include/asm/mach-db1x00/bcsr.h
@@ -34,6 +34,8 @@
#define PB1200_BCSR_PHYS_ADDR 0x0D800000
#define PB1200_BCSR_HEXLED_OFS 0x00400000
+#define DB1300_BCSR_PHYS_ADDR 0x19800000
+#define DB1300_BCSR_HEXLED_OFS 0x00400000
enum bcsr_id {
/* BCSR base 1 */
@@ -105,6 +107,7 @@
BCSR_WHOAMI_PB1200 = BCSR_WHOAMI_PB1200_DDR1,
BCSR_WHOAMI_PB1200_DDR2,
BCSR_WHOAMI_DB1200,
+ BCSR_WHOAMI_DB1300,
};
/* STATUS reg. Unless otherwise noted, they're valid on all boards.
@@ -118,12 +121,12 @@
#define BCSR_STATUS_SRAMWIDTH 0x0080
#define BCSR_STATUS_FLASHBUSY 0x0100
#define BCSR_STATUS_ROMBUSY 0x0400
-#define BCSR_STATUS_SD0WP 0x0400 /* DB1200 */
+#define BCSR_STATUS_SD0WP 0x0400 /* DB1200/DB1300:SD1 */
#define BCSR_STATUS_SD1WP 0x0800
#define BCSR_STATUS_USBOTGID 0x0800 /* PB/DB1550 */
#define BCSR_STATUS_DB1000_SWAPBOOT 0x2000
-#define BCSR_STATUS_DB1200_SWAPBOOT 0x0040 /* DB1200 */
-#define BCSR_STATUS_IDECBLID 0x0200 /* DB1200 */
+#define BCSR_STATUS_DB1200_SWAPBOOT 0x0040 /* DB1200/1300 */
+#define BCSR_STATUS_IDECBLID 0x0200 /* DB1200/1300 */
#define BCSR_STATUS_DB1200_U0RXD 0x1000 /* DB1200 */
#define BCSR_STATUS_DB1200_U1RXD 0x2000 /* DB1200 */
#define BCSR_STATUS_FLASHDEN 0xC000
@@ -133,6 +136,11 @@
#define BCSR_STATUS_PB1550_U1RXD 0x2000 /* PB1550 */
#define BCSR_STATUS_PB1550_U3RXD 0x8000 /* PB1550 */
+#define BCSR_STATUS_CFWP 0x4000 /* DB1300 */
+#define BCSR_STATUS_USBOCn 0x2000 /* DB1300 */
+#define BCSR_STATUS_OTGOCn 0x1000 /* DB1300 */
+#define BCSR_STATUS_DCDMARQ 0x0010 /* DB1300 */
+#define BCSR_STATUS_IDEDMARQ 0x0020 /* DB1300 */
/* DB/PB1000,1100,1500,1550 */
#define BCSR_RESETS_PHY0 0x0001
@@ -160,12 +168,12 @@
#define BCSR_BOARD_SD1WP 0x8000 /* DB1100 */
-/* DB/PB1200 */
+/* DB/PB1200/1300 */
#define BCSR_RESETS_ETH 0x0001
#define BCSR_RESETS_CAMERA 0x0002
#define BCSR_RESETS_DC 0x0004
#define BCSR_RESETS_IDE 0x0008
-#define BCSR_RESETS_TV 0x0010 /* DB1200 */
+#define BCSR_RESETS_TV 0x0010 /* DB1200/1300 */
/* Not resets but in the same register */
#define BCSR_RESETS_PWMR1MUX 0x0800 /* DB1200 */
#define BCSR_RESETS_PB1200_WSCFSM 0x0800 /* PB1200 */
@@ -174,13 +182,22 @@
#define BCSR_RESETS_SPISEL 0x4000
#define BCSR_RESETS_SD1MUX 0x8000 /* PB1200 */
+#define BCSR_RESETS_VDDQSHDN 0x0200 /* DB1300 */
+#define BCSR_RESETS_OTPPGM 0x0400 /* DB1300 */
+#define BCSR_RESETS_OTPSCLK 0x0800 /* DB1300 */
+#define BCSR_RESETS_OTPWRPROT 0x1000 /* DB1300 */
+#define BCSR_RESETS_OTPCSB 0x2000 /* DB1300 */
+#define BCSR_RESETS_OTGPWR 0x4000 /* DB1300 */
+#define BCSR_RESETS_USBHPWR 0x8000 /* DB1300 */
+
#define BCSR_BOARD_LCDVEE 0x0001
#define BCSR_BOARD_LCDVDD 0x0002
#define BCSR_BOARD_LCDBL 0x0004
#define BCSR_BOARD_CAMSNAP 0x0010
#define BCSR_BOARD_CAMPWR 0x0020
#define BCSR_BOARD_SD0PWR 0x0040
-
+#define BCSR_BOARD_CAMCS 0x0010 /* DB1300 */
+#define BCSR_BOARD_HDMI_DE 0x0040 /* DB1300 */
#define BCSR_SWITCHES_DIP 0x00FF
#define BCSR_SWITCHES_DIP_1 0x0080
@@ -214,7 +231,10 @@
#define BCSR_SYSTEM_RESET 0x8000 /* clear to reset */
#define BCSR_SYSTEM_PWROFF 0x4000 /* set to power off */
#define BCSR_SYSTEM_VDDI 0x001F /* PB1xxx boards */
-
+#define BCSR_SYSTEM_DEBUGCSMASK 0x003F /* DB1300 */
+#define BCSR_SYSTEM_UDMAMODE 0x0100 /* DB1300 */
+#define BCSR_SYSTEM_WAKEONIRQ 0x0200 /* DB1300 */
+#define BCSR_SYSTEM_VDDI1300 0x3C00 /* DB1300 */
diff --git a/arch/mips/include/asm/mach-db1x00/db1300.h b/arch/mips/include/asm/mach-db1x00/db1300.h
new file mode 100644
index 0000000..7fe5fb3
--- /dev/null
+++ b/arch/mips/include/asm/mach-db1x00/db1300.h
@@ -0,0 +1,40 @@
+/*
+ * NetLogic DB1300 board constants
+ */
+
+#ifndef _DB1300_H_
+#define _DB1300_H_
+
+/* FPGA (external mux) interrupt sources */
+#define DB1300_FIRST_INT (ALCHEMY_GPIC_INT_LAST + 1)
+#define DB1300_IDE_INT (DB1300_FIRST_INT + 0)
+#define DB1300_ETH_INT (DB1300_FIRST_INT + 1)
+#define DB1300_CF_INT (DB1300_FIRST_INT + 2)
+#define DB1300_VIDEO_INT (DB1300_FIRST_INT + 4)
+#define DB1300_HDMI_INT (DB1300_FIRST_INT + 5)
+#define DB1300_DC_INT (DB1300_FIRST_INT + 6)
+#define DB1300_FLASH_INT (DB1300_FIRST_INT + 7)
+#define DB1300_CF_INSERT_INT (DB1300_FIRST_INT + 8)
+#define DB1300_CF_EJECT_INT (DB1300_FIRST_INT + 9)
+#define DB1300_AC97_INT (DB1300_FIRST_INT + 10)
+#define DB1300_AC97_PEN_INT (DB1300_FIRST_INT + 11)
+#define DB1300_SD1_INSERT_INT (DB1300_FIRST_INT + 12)
+#define DB1300_SD1_EJECT_INT (DB1300_FIRST_INT + 13)
+#define DB1300_OTG_VBUS_OC_INT (DB1300_FIRST_INT + 14)
+#define DB1300_HOST_VBUS_OC_INT (DB1300_FIRST_INT + 15)
+#define DB1300_LAST_INT (DB1300_FIRST_INT + 15)
+
+/* SMSC9210 CS */
+#define DB1300_ETH_PHYS_ADDR 0x19000000
+#define DB1300_ETH_PHYS_END 0x197fffff
+
+/* ATA CS */
+#define DB1300_IDE_PHYS_ADDR 0x18800000
+#define DB1300_IDE_REG_SHIFT 5
+#define DB1300_IDE_PHYS_LEN (16 << DB1300_IDE_REG_SHIFT)
+
+/* NAND CS */
+#define DB1300_NAND_PHYS_ADDR 0x20000000
+#define DB1300_NAND_PHYS_END 0x20000fff
+
+#endif /* _DB1300_H_ */
diff --git a/arch/mips/include/asm/mach-db1x00/irq.h b/arch/mips/include/asm/mach-db1x00/irq.h
new file mode 100644
index 0000000..15b2669
--- /dev/null
+++ b/arch/mips/include/asm/mach-db1x00/irq.h
@@ -0,0 +1,23 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2003 by Ralf Baechle
+ */
+#ifndef __ASM_MACH_GENERIC_IRQ_H
+#define __ASM_MACH_GENERIC_IRQ_H
+
+
+#ifdef NR_IRQS
+#undef NR_IRQS
+#endif
+
+#ifndef MIPS_CPU_IRQ_BASE
+#define MIPS_CPU_IRQ_BASE 0
+#endif
+
+/* 8 (MIPS) + 128 (au1300) + 16 (cpld) */
+#define NR_IRQS 152
+
+#endif /* __ASM_MACH_GENERIC_IRQ_H */
diff --git a/drivers/pcmcia/Kconfig b/drivers/pcmcia/Kconfig
index c022b5c..f9e3fb3 100644
--- a/drivers/pcmcia/Kconfig
+++ b/drivers/pcmcia/Kconfig
@@ -161,8 +161,8 @@
select 64BIT_PHYS_ADDR
help
Enable this driver of you want PCMCIA support on your Alchemy
- Db1000, Db/Pb1100, Db/Pb1500, Db/Pb1550, Db/Pb1200 board.
- NOT suitable for the PB1000!
+ Db1000, Db/Pb1100, Db/Pb1500, Db/Pb1550, Db/Pb1200, DB1300
+ board. NOT suitable for the PB1000!
This driver is also available as a module called db1xxx_ss.ko
diff --git a/drivers/pcmcia/db1xxx_ss.c b/drivers/pcmcia/db1xxx_ss.c
index 3e49df6..5b7c227 100644
--- a/drivers/pcmcia/db1xxx_ss.c
+++ b/drivers/pcmcia/db1xxx_ss.c
@@ -7,7 +7,7 @@
/* This is a fairly generic PCMCIA socket driver suitable for the
* following Alchemy Development boards:
- * Db1000, Db/Pb1500, Db/Pb1100, Db/Pb1550, Db/Pb1200.
+ * Db1000, Db/Pb1500, Db/Pb1100, Db/Pb1550, Db/Pb1200, Db1300
*
* The Db1000 is used as a reference: Per-socket card-, carddetect- and
* statuschange IRQs connected to SoC GPIOs, control and status register
@@ -18,6 +18,7 @@
* - Pb1100/Pb1500: single socket only; voltage key bits VS are
* at STATUS[5:4] (instead of STATUS[1:0]).
* - Au1200-based: additional card-eject irqs, irqs not gpios!
+ * - Db1300: Db1200-like, no pwr ctrl, single socket (#1).
*/
#include <linux/delay.h>
@@ -59,11 +60,17 @@
#define BOARD_TYPE_DEFAULT 0 /* most boards */
#define BOARD_TYPE_DB1200 1 /* IRQs aren't gpios */
#define BOARD_TYPE_PB1100 2 /* VS bits slightly different */
+#define BOARD_TYPE_DB1300 3 /* no power control */
int board_type;
};
#define to_db1x_socket(x) container_of(x, struct db1x_pcmcia_sock, socket)
+static int db1300_card_inserted(struct db1x_pcmcia_sock *sock)
+{
+ return bcsr_read(BCSR_SIGSTAT) & (1 << 8);
+}
+
/* DB/PB1200: check CPLD SIGSTATUS register bit 10/12 */
static int db1200_card_inserted(struct db1x_pcmcia_sock *sock)
{
@@ -84,6 +91,8 @@
switch (sock->board_type) {
case BOARD_TYPE_DB1200:
return db1200_card_inserted(sock);
+ case BOARD_TYPE_DB1300:
+ return db1300_card_inserted(sock);
default:
return db1000_card_inserted(sock);
}
@@ -160,7 +169,8 @@
* ejection handler have been registered and the currently
* active one disabled.
*/
- if (sock->board_type == BOARD_TYPE_DB1200) {
+ if ((sock->board_type == BOARD_TYPE_DB1200) ||
+ (sock->board_type == BOARD_TYPE_DB1300)) {
ret = request_irq(sock->insert_irq, db1200_pcmcia_cdirq,
IRQF_DISABLED, "pcmcia_insert", sock);
if (ret)
@@ -174,7 +184,7 @@
}
/* enable the currently silent one */
- if (db1200_card_inserted(sock))
+ if (db1x_card_inserted(sock))
enable_irq(sock->eject_irq);
else
enable_irq(sock->insert_irq);
@@ -270,7 +280,8 @@
}
/* create new voltage code */
- cr_set |= ((v << 2) | p) << (sock->nr * 8);
+ if (sock->board_type != BOARD_TYPE_DB1300)
+ cr_set |= ((v << 2) | p) << (sock->nr * 8);
changed = state->flags ^ sock->old_flags;
@@ -343,6 +354,10 @@
/* if Vcc is not zero, we have applied power to a card */
status |= GET_VCC(cr, sock->nr) ? SS_POWERON : 0;
+ /* DB1300: power always on, but don't tell when no card present */
+ if ((sock->board_type == BOARD_TYPE_DB1300) && (status & SS_DETECT))
+ status = SS_POWERON | SS_3VCARD | SS_DETECT;
+
/* reset de-asserted? then we're ready */
status |= (GET_RESET(cr, sock->nr)) ? SS_READY : SS_RESET;
@@ -419,6 +434,9 @@
case BCSR_WHOAMI_PB1200 ... BCSR_WHOAMI_DB1200:
sock->board_type = BOARD_TYPE_DB1200;
break;
+ case BCSR_WHOAMI_DB1300:
+ sock->board_type = BOARD_TYPE_DB1300;
+ break;
default:
printk(KERN_INFO "db1xxx-ss: unknown board %d!\n", bid);
ret = -ENODEV;
diff --git a/drivers/video/au1200fb.c b/drivers/video/au1200fb.c
index 7200559..6c4342f 100644
--- a/drivers/video/au1200fb.c
+++ b/drivers/video/au1200fb.c
@@ -639,6 +639,42 @@
856, 856,
480, 480,
},
+ [9] = {
+ .name = "DB1300_800x480",
+ .monspecs = {
+ .modedb = NULL,
+ .modedb_len = 0,
+ .hfmin = 30000,
+ .hfmax = 70000,
+ .vfmin = 60,
+ .vfmax = 60,
+ .dclkmin = 6000000,
+ .dclkmax = 28000000,
+ .input = FB_DISP_RGB,
+ },
+ .mode_screen = LCD_SCREEN_SX_N(800) |
+ LCD_SCREEN_SY_N(480),
+ .mode_horztiming = LCD_HORZTIMING_HPW_N(5) |
+ LCD_HORZTIMING_HND1_N(16) |
+ LCD_HORZTIMING_HND2_N(8),
+ .mode_verttiming = LCD_VERTTIMING_VPW_N(4) |
+ LCD_VERTTIMING_VND1_N(8) |
+ LCD_VERTTIMING_VND2_N(5),
+ .mode_clkcontrol = LCD_CLKCONTROL_PCD_N(1) |
+ LCD_CLKCONTROL_IV |
+ LCD_CLKCONTROL_IH,
+ .mode_pwmdiv = 0x00000000,
+ .mode_pwmhi = 0x00000000,
+ .mode_outmask = 0x00FFFFFF,
+ .mode_fifoctrl = 0x2f2f2f2f,
+ .mode_toyclksrc = 0x00000004, /* AUXPLL directly */
+ .mode_backlight = 0x00000000,
+ .mode_auxpll = (48/12) * 2,
+ .device_init = board_au1200fb_panel_init,
+ .device_shutdown = board_au1200fb_panel_shutdown,
+ 800, 800,
+ 480, 480,
+ },
};
#define NUM_PANELS (ARRAY_SIZE(known_lcd_panels))
diff --git a/sound/soc/au1x/Kconfig b/sound/soc/au1x/Kconfig
index 93323cc..78b6649 100644
--- a/sound/soc/au1x/Kconfig
+++ b/sound/soc/au1x/Kconfig
@@ -51,12 +51,14 @@
of boards (DB1000/DB1500/DB1100).
config SND_SOC_DB1200
- tristate "DB1200 AC97+I2S audio support"
+ tristate "DB1200/DB1300 Audio support"
depends on SND_SOC_AU1XPSC
select SND_SOC_AU1XPSC_AC97
select SND_SOC_AC97_CODEC
+ select SND_SOC_WM9712
select SND_SOC_AU1XPSC_I2S
select SND_SOC_WM8731
help
- Select this option to enable audio (AC97 or I2S) on the
- Alchemy/AMD/RMI DB1200 demoboard.
+ Select this option to enable audio (AC97 and I2S) on the
+ Alchemy/AMD/RMI/NetLogic Db1200 and Db1300 evaluation boards.
+ If you need Db1300 touchscreen support, you definitely want to say Y.
diff --git a/sound/soc/au1x/db1200.c b/sound/soc/au1x/db1200.c
index 289312c..ca2335a 100644
--- a/sound/soc/au1x/db1200.c
+++ b/sound/soc/au1x/db1200.c
@@ -1,5 +1,5 @@
/*
- * DB1200 ASoC audio fabric support code.
+ * DB1200/DB1300 ASoC audio fabric support code.
*
* (c) 2008-2011 Manuel Lauss <manuel.lauss@googlemail.com>
*
@@ -28,6 +28,12 @@
}, {
.name = "db1200-i2s",
.driver_data = 1,
+ }, {
+ .name = "db1300-ac97",
+ .driver_data = 2,
+ }, {
+ .name = "db1300-i2s",
+ .driver_data = 3,
},
{},
};
@@ -49,6 +55,21 @@
.num_links = 1,
};
+static struct snd_soc_dai_link db1300_ac97_dai = {
+ .name = "AC97",
+ .stream_name = "AC97 HiFi",
+ .codec_dai_name = "wm9712-hifi",
+ .cpu_dai_name = "au1xpsc_ac97.1",
+ .platform_name = "au1xpsc-pcm.1",
+ .codec_name = "wm9712-codec.1",
+};
+
+static struct snd_soc_card db1300_ac97_machine = {
+ .name = "DB1300_AC97",
+ .dai_link = &db1300_ac97_dai,
+ .num_links = 1,
+};
+
/*------------------------- I2S PART ---------------------------*/
static int db1200_i2s_startup(struct snd_pcm_substream *substream)
@@ -98,11 +119,29 @@
.num_links = 1,
};
+static struct snd_soc_dai_link db1300_i2s_dai = {
+ .name = "WM8731",
+ .stream_name = "WM8731 PCM",
+ .codec_dai_name = "wm8731-hifi",
+ .cpu_dai_name = "au1xpsc_i2s.2",
+ .platform_name = "au1xpsc-pcm.2",
+ .codec_name = "wm8731.0-001b",
+ .ops = &db1200_i2s_wm8731_ops,
+};
+
+static struct snd_soc_card db1300_i2s_machine = {
+ .name = "DB1300_I2S",
+ .dai_link = &db1300_i2s_dai,
+ .num_links = 1,
+};
+
/*------------------------- COMMON PART ---------------------------*/
static struct snd_soc_card *db1200_cards[] __devinitdata = {
&db1200_ac97_machine,
&db1200_i2s_machine,
+ &db1300_ac97_machine,
+ &db1300_i2s_machine,
};
static int __devinit db1200_audio_probe(struct platform_device *pdev)
@@ -147,5 +186,5 @@
module_exit(db1200_audio_unload);
MODULE_LICENSE("GPL");
-MODULE_DESCRIPTION("DB1200 ASoC audio support");
+MODULE_DESCRIPTION("DB1200/DB1300 ASoC audio support");
MODULE_AUTHOR("Manuel Lauss");