[PATCH] skge: fiber support
Add support for older fiber versions of the SysKonnect board. These chipsets
use an internal PHY so they require special handling. The older sk98lin
driver already supported these
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
diff --git a/drivers/net/skge.h b/drivers/net/skge.h
index 79e0927..d0b47d4 100644
--- a/drivers/net/skge.h
+++ b/drivers/net/skge.h
@@ -934,7 +934,7 @@
PHY_XMAC_AUNE_ADV = 0x04,/* 16 bit r/w Auto-Neg. Advertisement */
PHY_XMAC_AUNE_LP = 0x05,/* 16 bit r/o Link Partner Abi Reg */
PHY_XMAC_AUNE_EXP = 0x06,/* 16 bit r/o Auto-Neg. Expansion Reg */
- PHY_XMAC_NEPG = 0x07,/* 16 bit r/w Next Page Register */
+ PHY_XMAC_NEPG = 0x07,/* 16 bit r/w Next Page Register */
PHY_XMAC_NEPG_LP = 0x08,/* 16 bit r/o Next Page Link Partner */
PHY_XMAC_EXT_STAT = 0x0f,/* 16 bit r/o Ext Status Register */
@@ -1097,13 +1097,36 @@
/* Pause Bits (PHY_X_AN_PAUSE and PHY_X_RS_PAUSE) encoding */
enum {
- PHY_X_P_NO_PAUSE = 0<<7,/* Bit 8..7: no Pause Mode */
+ PHY_X_P_NO_PAUSE= 0<<7,/* Bit 8..7: no Pause Mode */
PHY_X_P_SYM_MD = 1<<7, /* Bit 8..7: symmetric Pause Mode */
PHY_X_P_ASYM_MD = 2<<7,/* Bit 8..7: asymmetric Pause Mode */
PHY_X_P_BOTH_MD = 3<<7,/* Bit 8..7: both Pause Mode */
};
+/***** PHY_XMAC_EXT_STAT 16 bit r/w Extended Status Register *****/
+enum {
+ PHY_X_EX_FD = 1<<15, /* Bit 15: Device Supports Full Duplex */
+ PHY_X_EX_HD = 1<<14, /* Bit 14: Device Supports Half Duplex */
+};
+
+/***** PHY_XMAC_RES_ABI 16 bit r/o PHY Resolved Ability *****/
+enum {
+ PHY_X_RS_PAUSE = 3<<7, /* Bit 8..7: selected Pause Mode */
+ PHY_X_RS_HD = 1<<6, /* Bit 6: Half Duplex Mode selected */
+ PHY_X_RS_FD = 1<<5, /* Bit 5: Full Duplex Mode selected */
+ PHY_X_RS_ABLMIS = 1<<4, /* Bit 4: duplex or pause cap mismatch */
+ PHY_X_RS_PAUMIS = 1<<3, /* Bit 3: pause capability mismatch */
+};
+
+/* Remote Fault Bits (PHY_X_AN_RFB) encoding */
+enum {
+ X_RFB_OK = 0<<12,/* Bit 13..12 No errors, Link OK */
+ X_RFB_LF = 1<<12,/* Bit 13..12 Link Failure */
+ X_RFB_OFF = 2<<12,/* Bit 13..12 Offline */
+ X_RFB_AN_ERR = 3<<12,/* Bit 13..12 Auto-Negotiation Error */
+};
+
/* Broadcom-Specific */
/***** PHY_BCOM_1000T_CTRL 16 bit r/w 1000Base-T Control Reg *****/
enum {
@@ -2158,8 +2181,8 @@
XM_IS_LNK_AE = 1<<14, /* Bit 14: Link Asynchronous Event */
XM_IS_TX_ABORT = 1<<13, /* Bit 13: Transmit Abort, late Col. etc */
XM_IS_FRC_INT = 1<<12, /* Bit 12: Force INT bit set in GP */
- XM_IS_INP_ASS = 1<<11, /* Bit 11: Input Asserted, GP bit 0 set */
- XM_IS_LIPA_RC = 1<<10, /* Bit 10: Link Partner requests config */
+ XM_IS_INP_ASS = 1<<11, /* Bit 11: Input Asserted, GP bit 0 set */
+ XM_IS_LIPA_RC = 1<<10, /* Bit 10: Link Partner requests config */
XM_IS_RX_PAGE = 1<<9, /* Bit 9: Page Received */
XM_IS_TX_PAGE = 1<<8, /* Bit 8: Next Page Loaded for Transmit */
XM_IS_AND = 1<<7, /* Bit 7: Auto-Negotiation Done */
@@ -2172,9 +2195,7 @@
XM_IS_RX_COMP = 1<<0, /* Bit 0: Frame Rx Complete */
};
-#define XM_DEF_MSK (~(XM_IS_INP_ASS | XM_IS_LIPA_RC | XM_IS_RX_PAGE | \
- XM_IS_AND | XM_IS_RXC_OV | XM_IS_TXC_OV | \
- XM_IS_RXF_OV | XM_IS_TXF_UR))
+#define XM_DEF_MSK (~(XM_IS_RXC_OV | XM_IS_TXC_OV | XM_IS_RXF_OV | XM_IS_TXF_UR))
/* XM_HW_CFG 16 bit r/w Hardware Config Register */
@@ -2396,6 +2417,7 @@
u8 chip_rev;
u8 copper;
u8 ports;
+ u8 phy_type;
u32 ram_size;
u32 ram_offset;
@@ -2422,6 +2444,7 @@
struct net_device_stats net_stats;
+ struct work_struct link_thread;
u8 rx_csum;
u8 blink_on;
u8 flow_control;