xHCI: set USB2 hardware LPM
If the device pass the USB2 software LPM and the host supports hardware
LPM, enable hardware LPM for the device to let the host decide when to
put the link into lower power state.
If hardware LPM is enabled for a port and driver wants to put it into
suspend, it must first disable hardware LPM, resume the port into U0,
and then suspend the port.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
diff --git a/drivers/usb/host/xhci.c b/drivers/usb/host/xhci.c
index b0649a4..4648cc0 100644
--- a/drivers/usb/host/xhci.c
+++ b/drivers/usb/host/xhci.c
@@ -3286,6 +3286,11 @@
del_timer_sync(&virt_dev->eps[i].stop_cmd_timer);
}
+ if (udev->usb2_hw_lpm_enabled) {
+ xhci_set_usb2_hardware_lpm(hcd, udev, 0);
+ udev->usb2_hw_lpm_enabled = 0;
+ }
+
spin_lock_irqsave(&xhci->lock, flags);
/* Don't disable the slot if the host controller is dead. */
state = xhci_readl(xhci, &xhci->op_regs->status);
@@ -3699,20 +3704,87 @@
return ret;
}
+int xhci_set_usb2_hardware_lpm(struct usb_hcd *hcd,
+ struct usb_device *udev, int enable)
+{
+ struct xhci_hcd *xhci = hcd_to_xhci(hcd);
+ __le32 __iomem **port_array;
+ __le32 __iomem *pm_addr;
+ u32 temp;
+ unsigned int port_num;
+ unsigned long flags;
+ int u2del, hird;
+
+ if (hcd->speed == HCD_USB3 || !xhci->hw_lpm_support ||
+ !udev->lpm_capable)
+ return -EPERM;
+
+ if (!udev->parent || udev->parent->parent ||
+ udev->descriptor.bDeviceClass == USB_CLASS_HUB)
+ return -EPERM;
+
+ if (udev->usb2_hw_lpm_capable != 1)
+ return -EPERM;
+
+ spin_lock_irqsave(&xhci->lock, flags);
+
+ port_array = xhci->usb2_ports;
+ port_num = udev->portnum - 1;
+ pm_addr = port_array[port_num] + 1;
+ temp = xhci_readl(xhci, pm_addr);
+
+ xhci_dbg(xhci, "%s port %d USB2 hardware LPM\n",
+ enable ? "enable" : "disable", port_num);
+
+ u2del = HCS_U2_LATENCY(xhci->hcs_params3);
+ if (le32_to_cpu(udev->bos->ext_cap->bmAttributes) & (1 << 2))
+ hird = xhci_calculate_hird_besl(u2del, 1);
+ else
+ hird = xhci_calculate_hird_besl(u2del, 0);
+
+ if (enable) {
+ temp &= ~PORT_HIRD_MASK;
+ temp |= PORT_HIRD(hird) | PORT_RWE;
+ xhci_writel(xhci, temp, pm_addr);
+ temp = xhci_readl(xhci, pm_addr);
+ temp |= PORT_HLE;
+ xhci_writel(xhci, temp, pm_addr);
+ } else {
+ temp &= ~(PORT_HLE | PORT_RWE | PORT_HIRD_MASK);
+ xhci_writel(xhci, temp, pm_addr);
+ }
+
+ spin_unlock_irqrestore(&xhci->lock, flags);
+ return 0;
+}
+
int xhci_update_device(struct usb_hcd *hcd, struct usb_device *udev)
{
struct xhci_hcd *xhci = hcd_to_xhci(hcd);
int ret;
ret = xhci_usb2_software_lpm_test(hcd, udev);
- if (!ret)
+ if (!ret) {
xhci_dbg(xhci, "software LPM test succeed\n");
+ if (xhci->hw_lpm_support == 1) {
+ udev->usb2_hw_lpm_capable = 1;
+ ret = xhci_set_usb2_hardware_lpm(hcd, udev, 1);
+ if (!ret)
+ udev->usb2_hw_lpm_enabled = 1;
+ }
+ }
return 0;
}
#else
+int xhci_set_usb2_hardware_lpm(struct usb_hcd *hcd,
+ struct usb_device *udev, int enable)
+{
+ return 0;
+}
+
int xhci_update_device(struct usb_hcd *hcd, struct usb_device *udev)
{
return 0;