diff --git a/drivers/ata/pata_ali.c b/drivers/ata/pata_ali.c
new file mode 100644
index 0000000..0e0415e
--- /dev/null
+++ b/drivers/ata/pata_ali.c
@@ -0,0 +1,679 @@
+/*
+ * pata_ali.c 	- ALI 15x3 PATA for new ATA layer
+ *			  (C) 2005 Red Hat Inc
+ *			  Alan Cox <alan@redhat.com>
+ *
+ * based in part upon
+ * linux/drivers/ide/pci/alim15x3.c		Version 0.17	2003/01/02
+ *
+ *  Copyright (C) 1998-2000 Michel Aubry, Maintainer
+ *  Copyright (C) 1998-2000 Andrzej Krzysztofowicz, Maintainer
+ *  Copyright (C) 1999-2000 CJ, cjtsai@ali.com.tw, Maintainer
+ *
+ *  Copyright (C) 1998-2000 Andre Hedrick (andre@linux-ide.org)
+ *  May be copied or modified under the terms of the GNU General Public License
+ *  Copyright (C) 2002 Alan Cox <alan@redhat.com>
+ *  ALi (now ULi M5228) support by Clear Zhang <Clear.Zhang@ali.com.tw>
+ *
+ *  Documentation
+ *	Chipset documentation available under NDA only
+ *
+ *  TODO/CHECK
+ *	Cannot have ATAPI on both master & slave for rev < c2 (???) but
+ *	otherwise should do atapi DMA.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+#include <linux/dmi.h>
+
+#define DRV_NAME "pata_ali"
+#define DRV_VERSION "0.6.5"
+
+/*
+ *	Cable special cases
+ */
+
+static struct dmi_system_id cable_dmi_table[] = {
+	{
+		.ident = "HP Pavilion N5430",
+		.matches = {
+			DMI_MATCH(DMI_BOARD_VENDOR, "Hewlett-Packard"),
+			DMI_MATCH(DMI_BOARD_NAME, "OmniBook N32N-736"),
+		},
+	},
+	{ }
+};
+
+static int ali_cable_override(struct pci_dev *pdev)
+{
+	/* Fujitsu P2000 */
+	if (pdev->subsystem_vendor == 0x10CF && pdev->subsystem_device == 0x10AF)
+	   	return 1;
+	/* Systems by DMI */
+	if (dmi_check_system(cable_dmi_table))
+		return 1;
+	return 0;
+}
+
+/**
+ *	ali_c2_cable_detect	-	cable detection
+ *	@ap: ATA port
+ *
+ *	Perform cable detection for C2 and later revisions
+ */
+
+static int ali_c2_cable_detect(struct ata_port *ap)
+{
+	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+	u8 ata66;
+
+	/* Certain laptops use short but suitable cables and don't
+	   implement the detect logic */
+
+	if (ali_cable_override(pdev))
+		return ATA_CBL_PATA80;
+
+	/* Host view cable detect 0x4A bit 0 primary bit 1 secondary
+	   Bit set for 40 pin */
+	pci_read_config_byte(pdev, 0x4A, &ata66);
+	if (ata66 & (1 << ap->port_no))
+		return ATA_CBL_PATA40;
+	else
+		return ATA_CBL_PATA80;
+}
+
+/**
+ *	ali_early_error_handler	-	reset for eary chip
+ *	@ap: ATA port
+ *
+ *	Handle the reset callback for the later chips with cable detect
+ */
+
+static int ali_c2_pre_reset(struct ata_port *ap)
+{
+	ap->cbl = ali_c2_cable_detect(ap);
+	return ata_std_prereset(ap);
+}
+
+static void ali_c2_error_handler(struct ata_port *ap)
+{
+	ata_bmdma_drive_eh(ap, ali_c2_pre_reset,
+			       ata_std_softreset, NULL,
+			       ata_std_postreset);
+}
+
+/**
+ *	ali_early_cable_detect	-	cable detection
+ *	@ap: ATA port
+ *
+ *	Perform cable detection for older chipsets. This turns out to be
+ *	rather easy to implement
+ */
+
+static int ali_early_cable_detect(struct ata_port *ap)
+{
+	return ATA_CBL_PATA40;
+}
+
+/**
+ *	ali_early_probe_init	-	reset for early chip
+ *	@ap: ATA port
+ *
+ *	Handle the reset callback for the early (pre cable detect) chips.
+ */
+
+static int ali_early_pre_reset(struct ata_port *ap)
+{
+	ap->cbl = ali_early_cable_detect(ap);
+	return ata_std_prereset(ap);
+}
+
+static void ali_early_error_handler(struct ata_port *ap)
+{
+	return ata_bmdma_drive_eh(ap, ali_early_pre_reset,
+				     ata_std_softreset, NULL,
+				     ata_std_postreset);
+}
+
+/**
+ *	ali_20_filter		-	filter for earlier ALI DMA
+ *	@ap: ALi ATA port
+ *	@adev: attached device
+ *
+ *	Ensure that we do not do DMA on CD devices. We may be able to
+ *	fix that later on. Also ensure we do not do UDMA on WDC drives
+ */
+
+static unsigned long ali_20_filter(const struct ata_port *ap, struct ata_device *adev, unsigned long mask)
+{
+	char model_num[40];
+	/* No DMA on anything but a disk for now */
+	if (adev->class != ATA_DEV_ATA)
+		mask &= ~(ATA_MASK_MWDMA | ATA_MASK_UDMA);
+	ata_id_string(adev->id, model_num, ATA_ID_PROD_OFS, sizeof(model_num));
+	if (strstr(model_num, "WDC"))
+		return mask &= ~ATA_MASK_UDMA;
+	return ata_pci_default_filter(ap, adev, mask);
+}
+
+/**
+ *	ali_fifo_control	-	FIFO manager
+ *	@ap: ALi channel to control
+ *	@adev: device for FIFO control
+ *	@on: 0 for off 1 for on
+ *
+ *	Enable or disable the FIFO on a given device. Because of the way the
+ *	ALi FIFO works it provides a boost on ATA disk but can be confused by
+ *	ATAPI and we must therefore manage it.
+ */
+
+static void ali_fifo_control(struct ata_port *ap, struct ata_device *adev, int on)
+{
+	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+	int pio_fifo = 0x54 + ap->port_no;
+	u8 fifo;
+	int shift = 4 * adev->devno;
+
+	/* ATA - FIFO on set nibble to 0x05, ATAPI - FIFO off, set nibble to
+	   0x00. Not all the docs agree but the behaviour we now use is the
+	   one stated in the BIOS Programming Guide */
+	   
+	pci_read_config_byte(pdev, pio_fifo, &fifo);
+	fifo &= ~(0x0F << shift);
+	if (on)
+		fifo |= (on << shift);
+	pci_write_config_byte(pdev, pio_fifo, fifo);
+}
+
+/**
+ *	ali_program_modes	-	load mode registers
+ *	@ap: ALi channel to load
+ *	@adev: Device the timing is for
+ *	@cmd: Command timing
+ *	@data: Data timing
+ *	@ultra: UDMA timing or zero for off
+ *
+ *	Loads the timing registers for cmd/data and disable UDMA if
+ *	ultra is zero. If ultra is set then load and enable the UDMA
+ *	timing but do not touch the command/data timing.
+ */
+
+static void ali_program_modes(struct ata_port *ap, struct ata_device *adev, struct ata_timing *t, u8 ultra)
+{
+	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+	int cas = 0x58 + 4 * ap->port_no;	/* Command timing */
+	int cbt = 0x59 + 4 * ap->port_no;	/* Command timing */
+	int drwt = 0x5A + 4 * ap->port_no + adev->devno; /* R/W timing */
+	int udmat = 0x56 + ap->port_no;	/* UDMA timing */
+	int shift = 4 * adev->devno;
+	u8 udma;
+
+	if (t != NULL) {
+		t->setup = FIT(t->setup, 1, 8) & 7;
+		t->act8b = FIT(t->act8b, 1, 8) & 7;
+		t->rec8b = FIT(t->rec8b, 1, 16) & 15;
+		t->active = FIT(t->active, 1, 8) & 7;
+		t->recover = FIT(t->recover, 1, 16) & 15;
+
+		pci_write_config_byte(pdev, cas, t->setup);
+		pci_write_config_byte(pdev, cbt, (t->act8b << 4) | t->rec8b);
+		pci_write_config_byte(pdev, drwt, (t->active << 4) | t->recover);
+	}
+
+	/* Set up the UDMA enable */
+	pci_read_config_byte(pdev, udmat, &udma);
+	udma &= ~(0x0F << shift);
+	udma |= ultra << shift;
+	pci_write_config_byte(pdev, udmat, udma);
+}
+
+/**
+ *	ali_set_piomode	-	set initial PIO mode data
+ *	@ap: ATA interface
+ *	@adev: ATA device
+ *
+ *	Program the ALi registers for PIO mode. FIXME: add timings for
+ *	PIO5.
+ */
+
+static void ali_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+	struct ata_device *pair = ata_dev_pair(adev);
+	struct ata_timing t;
+	unsigned long T =  1000000000 / 33333;	/* PCI clock based */
+
+	ata_timing_compute(adev, adev->pio_mode, &t, T, 1);
+	if (pair) {
+		struct ata_timing p;
+		ata_timing_compute(pair, pair->pio_mode, &p, T, 1);
+		ata_timing_merge(&p, &t, &t, ATA_TIMING_SETUP|ATA_TIMING_8BIT);
+		if (pair->dma_mode) {
+			ata_timing_compute(pair, pair->dma_mode, &p, T, 1);
+			ata_timing_merge(&p, &t, &t, ATA_TIMING_SETUP|ATA_TIMING_8BIT);
+		}
+	}
+
+	/* PIO FIFO is only permitted on ATA disk */
+	if (adev->class != ATA_DEV_ATA)
+		ali_fifo_control(ap, adev, 0x00);
+	ali_program_modes(ap, adev, &t, 0);
+	if (adev->class == ATA_DEV_ATA)
+		ali_fifo_control(ap, adev, 0x05);
+
+}
+
+/**
+ *	ali_set_dmamode	-	set initial DMA mode data
+ *	@ap: ATA interface
+ *	@adev: ATA device
+ *
+ *	FIXME: MWDMA timings
+ */
+
+static void ali_set_dmamode(struct ata_port *ap, struct ata_device *adev)
+{
+	static u8 udma_timing[7] = { 0xC, 0xB, 0xA, 0x9, 0x8, 0xF, 0xD };
+	struct ata_device *pair = ata_dev_pair(adev);
+	struct ata_timing t;
+	unsigned long T =  1000000000 / 33333;	/* PCI clock based */
+	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+
+
+	if (adev->class == ATA_DEV_ATA)
+		ali_fifo_control(ap, adev, 0x08);
+
+	if (adev->dma_mode >= XFER_UDMA_0) {
+		ali_program_modes(ap, adev, NULL, udma_timing[adev->dma_mode - XFER_UDMA_0]);
+		if (adev->dma_mode >= XFER_UDMA_3) {
+			u8 reg4b;
+			pci_read_config_byte(pdev, 0x4B, &reg4b);
+			reg4b |= 1;
+			pci_write_config_byte(pdev, 0x4B, reg4b);
+		}
+	} else {
+		ata_timing_compute(adev, adev->dma_mode, &t, T, 1);
+		if (pair) {
+			struct ata_timing p;
+			ata_timing_compute(pair, pair->pio_mode, &p, T, 1);
+			ata_timing_merge(&p, &t, &t, ATA_TIMING_SETUP|ATA_TIMING_8BIT);
+			if (pair->dma_mode) {
+				ata_timing_compute(pair, pair->dma_mode, &p, T, 1);
+				ata_timing_merge(&p, &t, &t, ATA_TIMING_SETUP|ATA_TIMING_8BIT);
+			}
+		}
+		ali_program_modes(ap, adev, &t, 0);
+	}
+}
+
+/**
+ *	ali_lock_sectors	-	Keep older devices to 255 sector mode
+ *	@ap: ATA port
+ *	@adev: Device
+ *
+ *	Called during the bus probe for each device that is found. We use
+ *	this call to lock the sector count of the device to 255 or less on
+ *	older ALi controllers. If we didn't do this then large I/O's would
+ *	require LBA48 commands which the older ALi requires are issued by
+ *	slower PIO methods
+ */
+
+static void ali_lock_sectors(struct ata_port *ap, struct ata_device *adev)
+{
+	adev->max_sectors = 255;
+}
+
+static struct scsi_host_template ali_sht = {
+	.module			= THIS_MODULE,
+	.name			= DRV_NAME,
+	.ioctl			= ata_scsi_ioctl,
+	.queuecommand		= ata_scsi_queuecmd,
+	.can_queue		= ATA_DEF_QUEUE,
+	.this_id		= ATA_SHT_THIS_ID,
+	.sg_tablesize		= LIBATA_MAX_PRD,
+	/* Keep LBA28 counts so large I/O's don't turn LBA48 and PIO
+	   with older controllers. Not locked so will grow on C5 or later */
+	.max_sectors		= 255,
+	.cmd_per_lun		= ATA_SHT_CMD_PER_LUN,
+	.emulated		= ATA_SHT_EMULATED,
+	.use_clustering		= ATA_SHT_USE_CLUSTERING,
+	.proc_name		= DRV_NAME,
+	.dma_boundary		= ATA_DMA_BOUNDARY,
+	.slave_configure	= ata_scsi_slave_config,
+	.bios_param		= ata_std_bios_param,
+};
+
+/*
+ *	Port operations for PIO only ALi
+ */
+
+static struct ata_port_operations ali_early_port_ops = {
+	.port_disable	= ata_port_disable,
+	.set_piomode	= ali_set_piomode,
+	.tf_load	= ata_tf_load,
+	.tf_read	= ata_tf_read,
+	.check_status 	= ata_check_status,
+	.exec_command	= ata_exec_command,
+	.dev_select 	= ata_std_dev_select,
+
+	.freeze		= ata_bmdma_freeze,
+	.thaw		= ata_bmdma_thaw,
+	.error_handler	= ali_early_error_handler,
+	.post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+	.qc_prep 	= ata_qc_prep,
+	.qc_issue	= ata_qc_issue_prot,
+	.eng_timeout	= ata_eng_timeout,
+	.data_xfer	= ata_pio_data_xfer,
+
+	.irq_handler	= ata_interrupt,
+	.irq_clear	= ata_bmdma_irq_clear,
+
+	.port_start	= ata_port_start,
+	.port_stop	= ata_port_stop,
+	.host_stop	= ata_host_stop
+};
+
+/*
+ *	Port operations for DMA capable ALi without cable
+ *	detect
+ */
+static struct ata_port_operations ali_20_port_ops = {
+	.port_disable	= ata_port_disable,
+
+	.set_piomode	= ali_set_piomode,
+	.set_dmamode	= ali_set_dmamode,
+	.mode_filter	= ali_20_filter,
+
+	.tf_load	= ata_tf_load,
+	.tf_read	= ata_tf_read,
+	.check_status 	= ata_check_status,
+	.exec_command	= ata_exec_command,
+	.dev_select 	= ata_std_dev_select,
+	.dev_config	= ali_lock_sectors,
+
+	.freeze		= ata_bmdma_freeze,
+	.thaw		= ata_bmdma_thaw,
+	.error_handler	= ali_early_error_handler,
+	.post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+	.bmdma_setup 	= ata_bmdma_setup,
+	.bmdma_start 	= ata_bmdma_start,
+	.bmdma_stop	= ata_bmdma_stop,
+	.bmdma_status 	= ata_bmdma_status,
+
+	.qc_prep 	= ata_qc_prep,
+	.qc_issue	= ata_qc_issue_prot,
+	.eng_timeout	= ata_eng_timeout,
+	.data_xfer	= ata_pio_data_xfer,
+
+	.irq_handler	= ata_interrupt,
+	.irq_clear	= ata_bmdma_irq_clear,
+
+	.port_start	= ata_port_start,
+	.port_stop	= ata_port_stop,
+	.host_stop	= ata_host_stop
+};
+
+/*
+ *	Port operations for DMA capable ALi with cable detect
+ */
+static struct ata_port_operations ali_c2_port_ops = {
+	.port_disable	= ata_port_disable,
+	.set_piomode	= ali_set_piomode,
+	.set_dmamode	= ali_set_dmamode,
+	.mode_filter	= ata_pci_default_filter,
+	.tf_load	= ata_tf_load,
+	.tf_read	= ata_tf_read,
+	.check_status 	= ata_check_status,
+	.exec_command	= ata_exec_command,
+	.dev_select 	= ata_std_dev_select,
+	.dev_config	= ali_lock_sectors,
+
+	.freeze		= ata_bmdma_freeze,
+	.thaw		= ata_bmdma_thaw,
+	.error_handler	= ali_c2_error_handler,
+	.post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+	.bmdma_setup 	= ata_bmdma_setup,
+	.bmdma_start 	= ata_bmdma_start,
+	.bmdma_stop	= ata_bmdma_stop,
+	.bmdma_status 	= ata_bmdma_status,
+
+	.qc_prep 	= ata_qc_prep,
+	.qc_issue	= ata_qc_issue_prot,
+	.eng_timeout	= ata_eng_timeout,
+	.data_xfer	= ata_pio_data_xfer,
+
+	.irq_handler	= ata_interrupt,
+	.irq_clear	= ata_bmdma_irq_clear,
+
+	.port_start	= ata_port_start,
+	.port_stop	= ata_port_stop,
+	.host_stop	= ata_host_stop
+};
+
+/*
+ *	Port operations for DMA capable ALi with cable detect and LBA48
+ */
+static struct ata_port_operations ali_c5_port_ops = {
+	.port_disable	= ata_port_disable,
+	.set_piomode	= ali_set_piomode,
+	.set_dmamode	= ali_set_dmamode,
+	.mode_filter	= ata_pci_default_filter,
+	.tf_load	= ata_tf_load,
+	.tf_read	= ata_tf_read,
+	.check_status 	= ata_check_status,
+	.exec_command	= ata_exec_command,
+	.dev_select 	= ata_std_dev_select,
+
+	.freeze		= ata_bmdma_freeze,
+	.thaw		= ata_bmdma_thaw,
+	.error_handler	= ali_c2_error_handler,
+	.post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+	.bmdma_setup 	= ata_bmdma_setup,
+	.bmdma_start 	= ata_bmdma_start,
+	.bmdma_stop	= ata_bmdma_stop,
+	.bmdma_status 	= ata_bmdma_status,
+
+	.qc_prep 	= ata_qc_prep,
+	.qc_issue	= ata_qc_issue_prot,
+	.eng_timeout	= ata_eng_timeout,
+	.data_xfer	= ata_pio_data_xfer,
+
+	.irq_handler	= ata_interrupt,
+	.irq_clear	= ata_bmdma_irq_clear,
+
+	.port_start	= ata_port_start,
+	.port_stop	= ata_port_stop,
+	.host_stop	= ata_host_stop
+};
+
+/**
+ *	ali_init_one		-	discovery callback
+ *	@pdev: PCI device ID
+ *	@id: PCI table info
+ *
+ *	An ALi IDE interface has been discovered. Figure out what revision
+ *	and perform configuration work before handing it to the ATA layer
+ */
+
+static int ali_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
+{
+	static struct ata_port_info info_early = {
+		.sht = &ali_sht,
+		.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+		.pio_mask = 0x1f,
+		.port_ops = &ali_early_port_ops
+	};
+	/* Revision 0x20 added DMA */
+	static struct ata_port_info info_20 = {
+		.sht = &ali_sht,
+		.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST | ATA_FLAG_PIO_LBA48,
+		.pio_mask = 0x1f,
+		.mwdma_mask = 0x07,
+		.port_ops = &ali_20_port_ops
+	};
+	/* Revision 0x20 with support logic added UDMA */
+	static struct ata_port_info info_20_udma = {
+		.sht = &ali_sht,
+		.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST | ATA_FLAG_PIO_LBA48,
+		.pio_mask = 0x1f,
+		.mwdma_mask = 0x07, 
+		.udma_mask = 0x07,	/* UDMA33 */
+		.port_ops = &ali_20_port_ops
+	};
+	/* Revision 0xC2 adds UDMA66 */
+	static struct ata_port_info info_c2 = {
+		.sht = &ali_sht,
+		.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST | ATA_FLAG_PIO_LBA48,
+		.pio_mask = 0x1f,
+		.mwdma_mask = 0x07,
+		.udma_mask = 0x1f,
+		.port_ops = &ali_c2_port_ops
+	};
+	/* Revision 0xC3 is UDMA100 */
+	static struct ata_port_info info_c3 = {
+		.sht = &ali_sht,
+		.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST | ATA_FLAG_PIO_LBA48,
+		.pio_mask = 0x1f,
+		.mwdma_mask = 0x07,
+		.udma_mask = 0x3f,
+		.port_ops = &ali_c2_port_ops
+	};
+	/* Revision 0xC4 is UDMA133 */
+	static struct ata_port_info info_c4 = {
+		.sht = &ali_sht,
+		.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST | ATA_FLAG_PIO_LBA48,
+		.pio_mask = 0x1f,
+		.mwdma_mask = 0x07,
+		.udma_mask = 0x7f,
+		.port_ops = &ali_c2_port_ops
+	};
+	/* Revision 0xC5 is UDMA133 with LBA48 DMA */
+	static struct ata_port_info info_c5 = {
+		.sht = &ali_sht,
+		.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+		.pio_mask = 0x1f,
+		.mwdma_mask = 0x07,
+		.udma_mask = 0x7f,
+		.port_ops = &ali_c5_port_ops
+	};
+
+	static struct ata_port_info *port_info[2];
+	u8 rev, tmp;
+	struct pci_dev *north, *isa_bridge;
+
+	pci_read_config_byte(pdev, PCI_REVISION_ID, &rev);
+
+	/*
+	 * The chipset revision selects the driver operations and
+	 * mode data.
+	 */
+
+	if (rev < 0x20) {
+		port_info[0] = port_info[1] = &info_early;
+	} else if (rev < 0xC2) {
+		/* 1543-E/F, 1543C-C, 1543C-D, 1543C-E */
+		pci_read_config_byte(pdev, 0x4B, &tmp);
+		/* Clear CD-ROM DMA write bit */
+		tmp &= 0x7F;
+		pci_write_config_byte(pdev, 0x4B, tmp);
+        	port_info[0] = port_info[1] = &info_20;
+	} else if (rev == 0xC2) {
+        	port_info[0] = port_info[1] = &info_c2;
+	} else if (rev == 0xC3) {
+        	port_info[0] = port_info[1] = &info_c3;
+	} else if (rev == 0xC4) {
+        	port_info[0] = port_info[1] = &info_c4;
+	} else
+        	port_info[0] = port_info[1] = &info_c5;
+
+	if (rev >= 0xC2) {
+		/* Enable cable detection logic */
+		pci_read_config_byte(pdev, 0x4B, &tmp);
+		pci_write_config_byte(pdev, 0x4B, tmp | 0x08);
+	}
+
+	north = pci_get_slot(pdev->bus, PCI_DEVFN(0,0));
+	isa_bridge = pci_get_device(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M1533, NULL);
+
+	if (north && north->vendor == PCI_VENDOR_ID_AL) {
+		/* Configure the ALi bridge logic. For non ALi rely on BIOS.
+		   Set the south bridge enable bit */
+		pci_read_config_byte(isa_bridge, 0x79, &tmp);
+		if (rev == 0xC2)
+			pci_write_config_byte(isa_bridge, 0x79, tmp | 0x04);
+		else if (rev > 0xC2)
+			pci_write_config_byte(isa_bridge, 0x79, tmp | 0x02);
+	}
+
+	if (rev >= 0x20) {
+		if (rev < 0xC2) {
+			/* Are we paired with a UDMA capable chip */
+			pci_read_config_byte(isa_bridge, 0x5E, &tmp);
+			if ((tmp & 0x1E) == 0x12)
+		        	port_info[0] = port_info[1] = &info_20_udma;
+		}
+		/*
+		 * CD_ROM DMA on (0x53 bit 0). Enable this even if we want
+		 * to use PIO. 0x53 bit 1 (rev 20 only) - enable FIFO control
+		 * via 0x54/55.
+		 */
+		pci_read_config_byte(pdev, 0x53, &tmp);
+		if (rev <= 0x20)
+			tmp &= ~0x02;
+		if (rev == 0xc7)
+			tmp |= 0x03;
+		else
+			tmp |= 0x01;	/* CD_ROM enable for DMA */
+		pci_write_config_byte(pdev, 0x53, tmp);
+	}
+
+	pci_dev_put(isa_bridge);
+	pci_dev_put(north);
+
+	ata_pci_clear_simplex(pdev);
+	return ata_pci_init_one(pdev, port_info, 2);
+}
+
+static struct pci_device_id ali[] = {
+	{ PCI_DEVICE(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M5228), },
+	{ PCI_DEVICE(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M5229), },
+	{ 0, },
+};
+
+static struct pci_driver ali_pci_driver = {
+	.name 		= DRV_NAME,
+	.id_table	= ali,
+	.probe 		= ali_init_one,
+	.remove		= ata_pci_remove_one
+};
+
+static int __init ali_init(void)
+{
+	return pci_register_driver(&ali_pci_driver);
+}
+
+
+static void __exit ali_exit(void)
+{
+	pci_unregister_driver(&ali_pci_driver);
+}
+
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("low-level driver for ALi PATA");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, ali);
+MODULE_VERSION(DRV_VERSION);
+
+module_init(ali_init);
+module_exit(ali_exit);