crypto: sha1 - SSSE3 based SHA1 implementation for x86-64
This is an assembler implementation of the SHA1 algorithm using the
Supplemental SSE3 (SSSE3) instructions or, when available, the
Advanced Vector Extensions (AVX).
Testing with the tcrypt module shows the raw hash performance is up to
2.3 times faster than the C implementation, using 8k data blocks on a
Core 2 Duo T5500. For the smalest data set (16 byte) it is still 25%
faster.
Since this implementation uses SSE/YMM registers it cannot safely be
used in every situation, e.g. while an IRQ interrupts a kernel thread.
The implementation falls back to the generic SHA1 variant, if using
the SSE/YMM registers is not possible.
With this algorithm I was able to increase the throughput of a single
IPsec link from 344 Mbit/s to 464 Mbit/s on a Core 2 Quad CPU using
the SSSE3 variant -- a speedup of +34.8%.
Saving and restoring SSE/YMM state might make the actual throughput
fluctuate when there are FPU intensive userland applications running.
For example, meassuring the performance using iperf2 directly on the
machine under test gives wobbling numbers because iperf2 uses the FPU
for each packet to check if the reporting interval has expired (in the
above test I got min/max/avg: 402/484/464 MBit/s).
Using this algorithm on a IPsec gateway gives much more reasonable and
stable numbers, albeit not as high as in the directly connected case.
Here is the result from an RFC 2544 test run with a EXFO Packet Blazer
FTB-8510:
frame size sha1-generic sha1-ssse3 delta
64 byte 37.5 MBit/s 37.5 MBit/s 0.0%
128 byte 56.3 MBit/s 62.5 MBit/s +11.0%
256 byte 87.5 MBit/s 100.0 MBit/s +14.3%
512 byte 131.3 MBit/s 150.0 MBit/s +14.2%
1024 byte 162.5 MBit/s 193.8 MBit/s +19.3%
1280 byte 175.0 MBit/s 212.5 MBit/s +21.4%
1420 byte 175.0 MBit/s 218.7 MBit/s +25.0%
1518 byte 150.0 MBit/s 181.2 MBit/s +20.8%
The throughput for the largest frame size is lower than for the
previous size because the IP packets need to be fragmented in this
case to make there way through the IPsec tunnel.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Maxim Locktyukhin <maxim.locktyukhin@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
diff --git a/arch/x86/crypto/Makefile b/arch/x86/crypto/Makefile
index c04f1b7..57c7f7b 100644
--- a/arch/x86/crypto/Makefile
+++ b/arch/x86/crypto/Makefile
@@ -13,6 +13,7 @@
obj-$(CONFIG_CRYPTO_GHASH_CLMUL_NI_INTEL) += ghash-clmulni-intel.o
obj-$(CONFIG_CRYPTO_CRC32C_INTEL) += crc32c-intel.o
+obj-$(CONFIG_CRYPTO_SHA1_SSSE3) += sha1-ssse3.o
aes-i586-y := aes-i586-asm_32.o aes_glue.o
twofish-i586-y := twofish-i586-asm_32.o twofish_glue.o
@@ -25,3 +26,10 @@
aesni-intel-y := aesni-intel_asm.o aesni-intel_glue.o fpu.o
ghash-clmulni-intel-y := ghash-clmulni-intel_asm.o ghash-clmulni-intel_glue.o
+
+# enable AVX support only when $(AS) can actually assemble the instructions
+ifeq ($(call as-instr,vpxor %xmm0$(comma)%xmm1$(comma)%xmm2,yes,no),yes)
+AFLAGS_sha1_ssse3_asm.o += -DSHA1_ENABLE_AVX_SUPPORT
+CFLAGS_sha1_ssse3_glue.o += -DSHA1_ENABLE_AVX_SUPPORT
+endif
+sha1-ssse3-y := sha1_ssse3_asm.o sha1_ssse3_glue.o