nuvoton: Move the Nuvoton driver

Move the Nuvoton driver into drivers/net/ethernet/nuvoton/ and
make the necessary Kconfig and Makefile changes.

CC: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
diff --git a/MAINTAINERS b/MAINTAINERS
index ee4ebb4..d31fd9e 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -1127,7 +1127,7 @@
 F:	drivers/input/keyboard/w90p910_keypad.c
 F:	drivers/input/touchscreen/w90p910_ts.c
 F:	drivers/watchdog/nuc900_wdt.c
-F:	drivers/net/arm/w90p910_ether.c
+F:	drivers/net/ethernet/nuvoton/w90p910_ether.c
 F:	drivers/mtd/nand/nuc900_nand.c
 F:	drivers/rtc/rtc-nuc900.c
 F:	drivers/spi/spi_nuc900.c
diff --git a/drivers/net/arm/Kconfig b/drivers/net/arm/Kconfig
index fc94b4bd..57d16b9 100644
--- a/drivers/net/arm/Kconfig
+++ b/drivers/net/arm/Kconfig
@@ -10,12 +10,3 @@
 	help
 	  If you wish to compile a kernel for the AT91RM9200 and enable
 	  ethernet support, then you should always answer Y to this.
-
-config W90P910_ETH
-	tristate "Nuvoton w90p910 Ethernet support"
-	depends on ARM && ARCH_W90X900
-	select PHYLIB
-	select MII
-	help
-	  Say Y here if you want to use built-in Ethernet ports
-	  on w90p910 processor.
diff --git a/drivers/net/arm/Makefile b/drivers/net/arm/Makefile
index 462b3a4..fc0f85c 100644
--- a/drivers/net/arm/Makefile
+++ b/drivers/net/arm/Makefile
@@ -4,4 +4,3 @@
 #
 
 obj-$(CONFIG_ARM_AT91_ETHER)	+= at91_ether.o
-obj-$(CONFIG_W90P910_ETH)	+= w90p910_ether.o
diff --git a/drivers/net/ethernet/Kconfig b/drivers/net/ethernet/Kconfig
index ff07408..3893065 100644
--- a/drivers/net/ethernet/Kconfig
+++ b/drivers/net/ethernet/Kconfig
@@ -37,6 +37,7 @@
 source "drivers/net/ethernet/myricom/Kconfig"
 source "drivers/net/ethernet/natsemi/Kconfig"
 source "drivers/net/ethernet/8390/Kconfig"
+source "drivers/net/ethernet/nuvoton/Kconfig"
 source "drivers/net/ethernet/oki-semi/Kconfig"
 source "drivers/net/ethernet/pasemi/Kconfig"
 source "drivers/net/ethernet/qlogic/Kconfig"
diff --git a/drivers/net/ethernet/Makefile b/drivers/net/ethernet/Makefile
index 3a17413..e1f0b94 100644
--- a/drivers/net/ethernet/Makefile
+++ b/drivers/net/ethernet/Makefile
@@ -28,6 +28,7 @@
 obj-$(CONFIG_NET_VENDOR_MICREL) += micrel/
 obj-$(CONFIG_NET_VENDOR_MYRI) += myricom/
 obj-$(CONFIG_NET_VENDOR_NATSEMI) += natsemi/
+obj-$(CONFIG_NET_VENDOR_NUVOTON) += nuvoton/
 obj-$(CONFIG_NET_VENDOR_OKI) += oki-semi/
 obj-$(CONFIG_NET_VENDOR_PASEMI) += pasemi/
 obj-$(CONFIG_NET_VENDOR_QLOGIC) += qlogic/
diff --git a/drivers/net/ethernet/nuvoton/Kconfig b/drivers/net/ethernet/nuvoton/Kconfig
new file mode 100644
index 0000000..3b91c3b
--- /dev/null
+++ b/drivers/net/ethernet/nuvoton/Kconfig
@@ -0,0 +1,29 @@
+#
+# Nuvoton network device configuration
+#
+
+config NET_VENDOR_NUVOTON
+	bool "Nuvoton devices"
+	depends on ARM && ARCH_W90X900
+	---help---
+	  If you have a network (Ethernet) card belonging to this class, say Y
+	  and read the Ethernet-HOWTO, available from
+	  <http://www.tldp.org/docs.html#howto>.
+
+	  Note that the answer to this question doesn't directly affect the
+	  kernel: saying N will just cause the configurator to skip all
+	  the questions about Nuvoton cards. If you say Y, you will be asked
+	  for your specific card in the following questions.
+
+if NET_VENDOR_NUVOTON
+
+config W90P910_ETH
+	tristate "Nuvoton w90p910 Ethernet support"
+	depends on ARM && ARCH_W90X900
+	select PHYLIB
+	select MII
+	---help---
+	  Say Y here if you want to use built-in Ethernet ports
+	  on w90p910 processor.
+
+endif # NET_VENDOR_NUVOTON
diff --git a/drivers/net/ethernet/nuvoton/Makefile b/drivers/net/ethernet/nuvoton/Makefile
new file mode 100644
index 0000000..171aa04
--- /dev/null
+++ b/drivers/net/ethernet/nuvoton/Makefile
@@ -0,0 +1,5 @@
+#
+# Makefile for the Nuvoton network device drivers.
+#
+
+obj-$(CONFIG_W90P910_ETH) += w90p910_ether.o
diff --git a/drivers/net/arm/w90p910_ether.c b/drivers/net/ethernet/nuvoton/w90p910_ether.c
similarity index 100%
rename from drivers/net/arm/w90p910_ether.c
rename to drivers/net/ethernet/nuvoton/w90p910_ether.c