diff --git a/drivers/hwmon/w83793.c b/drivers/hwmon/w83793.c
new file mode 100644
index 0000000..c12ac5a
--- /dev/null
+++ b/drivers/hwmon/w83793.c
@@ -0,0 +1,1609 @@
+/*
+    w83793.c - Linux kernel driver for hardware monitoring
+    Copyright (C) 2006 Winbond Electronics Corp.
+                  Yuan Mu
+                  Rudolf Marek <r.marek@assembler.cz>
+
+    This program is free software; you can redistribute it and/or modify
+    it under the terms of the GNU General Public License as published by
+    the Free Software Foundation - version 2.
+
+    This program is distributed in the hope that it will be useful,
+    but WITHOUT ANY WARRANTY; without even the implied warranty of
+    MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+    GNU General Public License for more details.
+
+    You should have received a copy of the GNU General Public License
+    along with this program; if not, write to the Free Software
+    Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA
+    02110-1301 USA.
+*/
+
+/*
+    Supports following chips:
+
+    Chip	#vin	#fanin	#pwm	#temp	wchipid	vendid	i2c	ISA
+    w83793	10	12	8	6	0x7b	0x5ca3	yes	no
+*/
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/slab.h>
+#include <linux/i2c.h>
+#include <linux/hwmon.h>
+#include <linux/hwmon-vid.h>
+#include <linux/hwmon-sysfs.h>
+#include <linux/err.h>
+#include <linux/mutex.h>
+
+/* Addresses to scan */
+static unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, 0x2f, I2C_CLIENT_END };
+
+/* Insmod parameters */
+I2C_CLIENT_INSMOD_1(w83793);
+I2C_CLIENT_MODULE_PARM(force_subclients, "List of subclient addresses: "
+		       "{bus, clientaddr, subclientaddr1, subclientaddr2}");
+
+static int reset;
+module_param(reset, bool, 0);
+MODULE_PARM_DESC(reset, "Set to 1 to reset chip, not recommended");
+
+/*
+   Address 0x00, 0x0d, 0x0e, 0x0f in all three banks are reserved
+   as ID, Bank Select registers
+*/
+#define W83793_REG_BANKSEL		0x00
+#define W83793_REG_VENDORID		0x0d
+#define W83793_REG_CHIPID		0x0e
+#define W83793_REG_DEVICEID		0x0f
+
+#define W83793_REG_CONFIG		0x40
+#define W83793_REG_MFC			0x58
+#define W83793_REG_FANIN_CTRL		0x5c
+#define W83793_REG_FANIN_SEL		0x5d
+#define W83793_REG_I2C_ADDR		0x0b
+#define W83793_REG_I2C_SUBADDR		0x0c
+#define W83793_REG_VID_INA		0x05
+#define W83793_REG_VID_INB		0x06
+#define W83793_REG_VID_LATCHA		0x07
+#define W83793_REG_VID_LATCHB		0x08
+#define W83793_REG_VID_CTRL		0x59
+
+static u16 W83793_REG_TEMP_MODE[2] = { 0x5e, 0x5f };
+
+#define TEMP_READ	0
+#define TEMP_CRIT	1
+#define TEMP_CRIT_HYST	2
+#define TEMP_WARN	3
+#define TEMP_WARN_HYST	4
+/* only crit and crit_hyst affect real-time alarm status
+   current crit crit_hyst warn warn_hyst */
+static u16 W83793_REG_TEMP[][5] = {
+	{0x1c, 0x78, 0x79, 0x7a, 0x7b},
+	{0x1d, 0x7c, 0x7d, 0x7e, 0x7f},
+	{0x1e, 0x80, 0x81, 0x82, 0x83},
+	{0x1f, 0x84, 0x85, 0x86, 0x87},
+	{0x20, 0x88, 0x89, 0x8a, 0x8b},
+	{0x21, 0x8c, 0x8d, 0x8e, 0x8f},
+};
+
+#define W83793_REG_TEMP_LOW_BITS	0x22
+
+#define W83793_REG_BEEP(index)		(0x53 + (index))
+#define W83793_REG_ALARM(index)		(0x4b + (index))
+
+#define W83793_REG_CLR_CHASSIS		0x4a	/* SMI MASK4 */
+#define W83793_REG_IRQ_CTRL		0x50
+#define W83793_REG_OVT_CTRL		0x51
+#define W83793_REG_OVT_BEEP		0x52
+
+#define IN_READ				0
+#define IN_MAX				1
+#define IN_LOW				2
+static const u16 W83793_REG_IN[][3] = {
+	/* Current, High, Low */
+	{0x10, 0x60, 0x61},	/* Vcore A	*/
+	{0x11, 0x62, 0x63},	/* Vcore B	*/
+	{0x12, 0x64, 0x65},	/* Vtt		*/
+	{0x14, 0x6a, 0x6b},	/* VSEN1	*/
+	{0x15, 0x6c, 0x6d},	/* VSEN2	*/
+	{0x16, 0x6e, 0x6f},	/* +3VSEN	*/
+	{0x17, 0x70, 0x71},	/* +12VSEN	*/
+	{0x18, 0x72, 0x73},	/* 5VDD		*/
+	{0x19, 0x74, 0x75},	/* 5VSB		*/
+	{0x1a, 0x76, 0x77},	/* VBAT		*/
+};
+
+/* Low Bits of Vcore A/B Vtt Read/High/Low */
+static const u16 W83793_REG_IN_LOW_BITS[] = { 0x1b, 0x68, 0x69 };
+static u8 scale_in[] = { 2, 2, 2, 16, 16, 16, 8, 24, 24, 16 };
+
+#define W83793_REG_FAN(index)		(0x23 + 2 * (index))	/* High byte */
+#define W83793_REG_FAN_MIN(index)	(0x90 + 2 * (index))	/* High byte */
+
+#define W83793_REG_PWM_DEFAULT		0xb2
+#define W83793_REG_PWM_ENABLE		0x207
+#define W83793_REG_PWM_UPTIME		0xc3	/* Unit in 0.1 second */
+#define W83793_REG_PWM_DOWNTIME		0xc4	/* Unit in 0.1 second */
+#define W83793_REG_TEMP_CRITICAL	0xc5
+
+#define PWM_DUTY			0
+#define PWM_START			1
+#define PWM_NONSTOP			2
+#define W83793_REG_PWM(index, nr)	(((nr) == 0 ? 0xb3 : \
+					 (nr) == 1 ? 0x220 : 0x218) + (index))
+
+/* bit field, fan1 is bit0, fan2 is bit1 ... */
+#define W83793_REG_TEMP_FAN_MAP(index)	(0x201 + (index))
+#define W83793_REG_TEMP_TOL(index)	(0x208 + (index))
+#define W83793_REG_TEMP_CRUISE(index)	(0x210 + (index))
+#define W83793_REG_PWM_STOP_TIME(index)	(0x228 + (index))
+#define W83793_REG_SF2_TEMP(index, nr)	(0x230 + ((index) << 4) + (nr))
+#define W83793_REG_SF2_PWM(index, nr)	(0x238 + ((index) << 4) + (nr))
+
+static inline unsigned long FAN_FROM_REG(u16 val)
+{
+	if ((val >= 0xfff) || (val == 0))
+		return	0;
+	return (1350000UL / val);
+}
+
+static inline u16 FAN_TO_REG(long rpm)
+{
+	if (rpm <= 0)
+		return 0x0fff;
+	return SENSORS_LIMIT((1350000 + (rpm >> 1)) / rpm, 1, 0xffe);
+}
+
+static inline unsigned long TIME_FROM_REG(u8 reg)
+{
+	return (reg * 100);
+}
+
+static inline u8 TIME_TO_REG(unsigned long val)
+{
+	return SENSORS_LIMIT((val + 50) / 100, 0, 0xff);
+}
+
+static inline long TEMP_FROM_REG(s8 reg)
+{
+	return (reg * 1000);
+}
+
+static inline s8 TEMP_TO_REG(long val, s8 min, s8 max)
+{
+	return SENSORS_LIMIT((val + (val < 0 ? -500 : 500)) / 1000, min, max);
+}
+
+struct w83793_data {
+	struct i2c_client client;
+	struct i2c_client *lm75[2];
+	struct class_device *class_dev;
+	struct mutex update_lock;
+	char valid;			/* !=0 if following fields are valid */
+	unsigned long last_updated;	/* In jiffies */
+	unsigned long last_nonvolatile;	/* In jiffies, last time we update the
+					   nonvolatile registers */
+
+	u8 bank;
+	u8 vrm;
+	u8 vid[2];
+	u8 in[10][3];		/* Register value, read/high/low */
+	u8 in_low_bits[3];	/* Additional resolution for VCore A/B Vtt */
+
+	u16 has_fan;		/* Only fan1- fan5 has own pins */
+	u16 fan[12];		/* Register value combine */
+	u16 fan_min[12];	/* Register value combine */
+
+	s8 temp[6][5];		/* current, crit, crit_hyst,warn, warn_hyst */
+	u8 temp_low_bits;	/* Additional resolution TD1-TD4 */
+	u8 temp_mode[2];	/* byte 0: Temp D1-D4 mode each has 2 bits
+				   byte 1: Temp R1,R2 mode, each has 1 bit */
+	u8 temp_critical;	/* If reached all fan will be at full speed */
+	u8 temp_fan_map[6];	/* Temp controls which pwm fan, bit field */
+
+	u8 has_pwm;
+	u8 pwm_enable;		/* Register value, each Temp has 1 bit */
+	u8 pwm_uptime;		/* Register value */
+	u8 pwm_downtime;	/* Register value */
+	u8 pwm_default;		/* All fan default pwm, next poweron valid */
+	u8 pwm[8][3];		/* Register value */
+	u8 pwm_stop_time[8];
+	u8 temp_cruise[6];
+
+	u8 alarms[5];		/* realtime status registers */
+	u8 beeps[5];
+	u8 beep_enable;
+	u8 tolerance[3];	/* Temp tolerance(Smart Fan I/II) */
+	u8 sf2_pwm[6][7];	/* Smart FanII: Fan duty cycle */
+	u8 sf2_temp[6][7];	/* Smart FanII: Temp level point */
+};
+
+static u8 w83793_read_value(struct i2c_client *client, u16 reg);
+static int w83793_write_value(struct i2c_client *client, u16 reg, u8 value);
+static int w83793_attach_adapter(struct i2c_adapter *adapter);
+static int w83793_detect(struct i2c_adapter *adapter, int address, int kind);
+static int w83793_detach_client(struct i2c_client *client);
+static void w83793_init_client(struct i2c_client *client);
+static void w83793_update_nonvolatile(struct device *dev);
+static struct w83793_data *w83793_update_device(struct device *dev);
+
+static struct i2c_driver w83793_driver = {
+	.driver = {
+		   .name = "w83793",
+	},
+	.attach_adapter = w83793_attach_adapter,
+	.detach_client = w83793_detach_client,
+};
+
+static ssize_t
+show_vrm(struct device *dev, struct device_attribute *attr, char *buf)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct w83793_data *data = i2c_get_clientdata(client);
+
+	return sprintf(buf, "%d\n", data->vrm);
+}
+
+static ssize_t
+show_vid(struct device *dev, struct device_attribute *attr, char *buf)
+{
+	struct w83793_data *data = w83793_update_device(dev);
+	struct sensor_device_attribute_2 *sensor_attr =
+	    to_sensor_dev_attr_2(attr);
+	int index = sensor_attr->index;
+
+	return sprintf(buf, "%d\n", vid_from_reg(data->vid[index], data->vrm));
+}
+
+static ssize_t
+store_vrm(struct device *dev, struct device_attribute *attr,
+	  const char *buf, size_t count)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct w83793_data *data = i2c_get_clientdata(client);
+
+	data->vrm = simple_strtoul(buf, NULL, 10);
+	return count;
+}
+
+#define ALARM_STATUS			0
+#define BEEP_ENABLE			1
+static ssize_t
+show_alarm_beep(struct device *dev, struct device_attribute *attr, char *buf)
+{
+	struct w83793_data *data = w83793_update_device(dev);
+	struct sensor_device_attribute_2 *sensor_attr =
+	    to_sensor_dev_attr_2(attr);
+	int nr = sensor_attr->nr;
+	int index = sensor_attr->index >> 3;
+	int bit = sensor_attr->index & 0x07;
+	u8 val;
+
+	if (ALARM_STATUS == nr) {
+		val = (data->alarms[index] >> (bit)) & 1;
+	} else {		/* BEEP_ENABLE */
+		val = (data->beeps[index] >> (bit)) & 1;
+	}
+
+	return sprintf(buf, "%u\n", val);
+}
+
+static ssize_t
+store_beep(struct device *dev, struct device_attribute *attr,
+	   const char *buf, size_t count)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct w83793_data *data = i2c_get_clientdata(client);
+	struct sensor_device_attribute_2 *sensor_attr =
+	    to_sensor_dev_attr_2(attr);
+	int index = sensor_attr->index >> 3;
+	int shift = sensor_attr->index & 0x07;
+	u8 beep_bit = 1 << shift;
+	u8 val;
+
+	val = simple_strtoul(buf, NULL, 10);
+	if (val != 0 && val != 1)
+		return -EINVAL;
+
+	mutex_lock(&data->update_lock);
+	data->beeps[index] = w83793_read_value(client, W83793_REG_BEEP(index));
+	data->beeps[index] &= ~beep_bit;
+	data->beeps[index] |= val << shift;
+	w83793_write_value(client, W83793_REG_BEEP(index), data->beeps[index]);
+	mutex_unlock(&data->update_lock);
+
+	return count;
+}
+
+static ssize_t
+show_beep_enable(struct device *dev, struct device_attribute *attr, char *buf)
+{
+	struct w83793_data *data = w83793_update_device(dev);
+	return sprintf(buf, "%u\n", (data->beep_enable >> 1) & 0x01);
+}
+
+static ssize_t
+store_beep_enable(struct device *dev, struct device_attribute *attr,
+		  const char *buf, size_t count)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct w83793_data *data = i2c_get_clientdata(client);
+	u8 val = simple_strtoul(buf, NULL, 10);
+
+	if (val != 0 && val != 1)
+		return -EINVAL;
+
+	mutex_lock(&data->update_lock);
+	data->beep_enable = w83793_read_value(client, W83793_REG_OVT_BEEP)
+			    & 0xfd;
+	data->beep_enable |= val << 1;
+	w83793_write_value(client, W83793_REG_OVT_BEEP, data->beep_enable);
+	mutex_unlock(&data->update_lock);
+
+	return count;
+}
+
+/* Write any value to clear chassis alarm */
+static ssize_t
+store_chassis_clear(struct device *dev,
+		    struct device_attribute *attr, const char *buf,
+		    size_t count)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct w83793_data *data = i2c_get_clientdata(client);
+	u8 val;
+
+	mutex_lock(&data->update_lock);
+	val = w83793_read_value(client, W83793_REG_CLR_CHASSIS);
+	val |= 0x80;
+	w83793_write_value(client, W83793_REG_CLR_CHASSIS, val);
+	mutex_unlock(&data->update_lock);
+	return count;
+}
+
+#define FAN_INPUT			0
+#define FAN_MIN				1
+static ssize_t
+show_fan(struct device *dev, struct device_attribute *attr, char *buf)
+{
+	struct sensor_device_attribute_2 *sensor_attr =
+	    to_sensor_dev_attr_2(attr);
+	int nr = sensor_attr->nr;
+	int index = sensor_attr->index;
+	struct w83793_data *data = w83793_update_device(dev);
+	u16 val;
+
+	if (FAN_INPUT == nr) {
+		val = data->fan[index] & 0x0fff;
+	} else {
+		val = data->fan_min[index] & 0x0fff;
+	}
+
+	return sprintf(buf, "%lu\n", FAN_FROM_REG(val));
+}
+
+static ssize_t
+store_fan_min(struct device *dev, struct device_attribute *attr,
+	      const char *buf, size_t count)
+{
+	struct sensor_device_attribute_2 *sensor_attr =
+	    to_sensor_dev_attr_2(attr);
+	int index = sensor_attr->index;
+	struct i2c_client *client = to_i2c_client(dev);
+	struct w83793_data *data = i2c_get_clientdata(client);
+	u16 val = FAN_TO_REG(simple_strtoul(buf, NULL, 10));
+
+	mutex_lock(&data->update_lock);
+	data->fan_min[index] = val;
+	w83793_write_value(client, W83793_REG_FAN_MIN(index),
+			   (val >> 8) & 0xff);
+	w83793_write_value(client, W83793_REG_FAN_MIN(index) + 1, val & 0xff);
+	mutex_unlock(&data->update_lock);
+
+	return count;
+}
+
+#define PWM_DUTY			0
+#define PWM_START			1
+#define PWM_NONSTOP			2
+#define PWM_STOP_TIME			3
+static ssize_t
+show_pwm(struct device *dev, struct device_attribute *attr, char *buf)
+{
+	struct sensor_device_attribute_2 *sensor_attr =
+	    to_sensor_dev_attr_2(attr);
+	struct w83793_data *data = w83793_update_device(dev);
+	u16 val;
+	int nr = sensor_attr->nr;
+	int index = sensor_attr->index;
+
+	if (PWM_STOP_TIME == nr)
+		val = TIME_FROM_REG(data->pwm_stop_time[index]);
+	else
+		val = (data->pwm[index][nr] & 0x3f) << 2;
+
+	return sprintf(buf, "%d\n", val);
+}
+
+static ssize_t
+store_pwm(struct device *dev, struct device_attribute *attr,
+	  const char *buf, size_t count)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct w83793_data *data = i2c_get_clientdata(client);
+	struct sensor_device_attribute_2 *sensor_attr =
+	    to_sensor_dev_attr_2(attr);
+	int nr = sensor_attr->nr;
+	int index = sensor_attr->index;
+	u8 val;
+
+	mutex_lock(&data->update_lock);
+	if (PWM_STOP_TIME == nr) {
+		val = TIME_TO_REG(simple_strtoul(buf, NULL, 10));
+		data->pwm_stop_time[index] = val;
+		w83793_write_value(client, W83793_REG_PWM_STOP_TIME(index),
+				   val);
+	} else {
+		val = SENSORS_LIMIT(simple_strtoul(buf, NULL, 10), 0, 0xff)
+		      >> 2;
+		data->pwm[index][nr] =
+		    w83793_read_value(client, W83793_REG_PWM(index, nr)) & 0xc0;
+		data->pwm[index][nr] |= val;
+		w83793_write_value(client, W83793_REG_PWM(index, nr),
+							data->pwm[index][nr]);
+	}
+
+	mutex_unlock(&data->update_lock);
+	return count;
+}
+
+static ssize_t
+show_temp(struct device *dev, struct device_attribute *attr, char *buf)
+{
+	struct sensor_device_attribute_2 *sensor_attr =
+	    to_sensor_dev_attr_2(attr);
+	int nr = sensor_attr->nr;
+	int index = sensor_attr->index;
+	struct w83793_data *data = w83793_update_device(dev);
+	long temp = TEMP_FROM_REG(data->temp[index][nr]);
+
+	if (TEMP_READ == nr && index < 4) {	/* Only TD1-TD4 have low bits */
+		int low = ((data->temp_low_bits >> (index * 2)) & 0x03) * 250;
+		temp += temp > 0 ? low : -low;
+	}
+	return sprintf(buf, "%ld\n", temp);
+}
+
+static ssize_t
+store_temp(struct device *dev, struct device_attribute *attr,
+	   const char *buf, size_t count)
+{
+	struct sensor_device_attribute_2 *sensor_attr =
+	    to_sensor_dev_attr_2(attr);
+	int nr = sensor_attr->nr;
+	int index = sensor_attr->index;
+	struct i2c_client *client = to_i2c_client(dev);
+	struct w83793_data *data = i2c_get_clientdata(client);
+	long tmp = simple_strtol(buf, NULL, 10);
+
+	mutex_lock(&data->update_lock);
+	data->temp[index][nr] = TEMP_TO_REG(tmp, -128, 127);
+	w83793_write_value(client, W83793_REG_TEMP[index][nr],
+			   data->temp[index][nr]);
+	mutex_unlock(&data->update_lock);
+	return count;
+}
+
+/*
+	TD1-TD4
+	each has 4 mode:(2 bits)
+	0:	Stop monitor
+	1:	Use internal temp sensor(default)
+	2:	Use sensor in AMD CPU and get result by AMDSI
+	3:	Use sensor in Intel CPU and get result by PECI
+
+	TR1-TR2
+	each has 2 mode:(1 bit)
+	0:	Disable temp sensor monitor
+	1:	To enable temp sensors monitor
+*/
+
+/* 0 disable, 5 AMDSI, 6 PECI */
+static u8 TO_TEMP_MODE[] = { 0, 0, 5, 6 };
+
+static ssize_t
+show_temp_mode(struct device *dev, struct device_attribute *attr, char *buf)
+{
+	struct w83793_data *data = w83793_update_device(dev);
+	struct sensor_device_attribute_2 *sensor_attr =
+	    to_sensor_dev_attr_2(attr);
+	int index = sensor_attr->index;
+	u8 mask = (index < 4) ? 0x03 : 0x01;
+	u8 shift = (index < 4) ? (2 * index) : (index - 4);
+	u8 tmp;
+	index = (index < 4) ? 0 : 1;
+
+	tmp = (data->temp_mode[index] >> shift) & mask;
+
+	/* for the internal sensor, found out if diode or thermistor */
+	if (tmp == 1) {
+		tmp = index == 0 ? 3 : 4;
+	} else {
+		tmp = TO_TEMP_MODE[tmp];
+	}
+
+	return sprintf(buf, "%d\n", tmp);
+}
+
+static ssize_t
+store_temp_mode(struct device *dev, struct device_attribute *attr,
+		const char *buf, size_t count)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct w83793_data *data = i2c_get_clientdata(client);
+	struct sensor_device_attribute_2 *sensor_attr =
+	    to_sensor_dev_attr_2(attr);
+	int index = sensor_attr->index;
+	u8 mask = (index < 4) ? 0x03 : 0x01;
+	u8 shift = (index < 4) ? (2 * index) : (index - 4);
+	u8 val = simple_strtoul(buf, NULL, 10);
+
+	/* transform the sysfs interface values into table above */
+	if ((val == 5 || val == 6) && (index < 4)) {
+		val -= 3;
+	} else if ((val == 3 && index < 4)
+		|| (val == 4 && index >= 4)
+		|| val == 0) {
+		/* transform diode or thermistor into internal enable */
+		val = !!val;
+	} else {
+		return -EINVAL;
+	}
+
+	index = (index < 4) ? 0 : 1;
+	mutex_lock(&data->update_lock);
+	data->temp_mode[index] =
+	    w83793_read_value(client, W83793_REG_TEMP_MODE[index]);
+	data->temp_mode[index] &= ~(mask << shift);
+	data->temp_mode[index] |= val << shift;
+	w83793_write_value(client, W83793_REG_TEMP_MODE[index],
+							data->temp_mode[index]);
+	mutex_unlock(&data->update_lock);
+
+	return count;
+}
+
+#define SETUP_PWM_DEFAULT		0
+#define SETUP_PWM_UPTIME		1	/* Unit in 0.1s */
+#define SETUP_PWM_DOWNTIME		2	/* Unit in 0.1s */
+#define SETUP_TEMP_CRITICAL		3
+static ssize_t
+show_sf_setup(struct device *dev, struct device_attribute *attr, char *buf)
+{
+	struct sensor_device_attribute_2 *sensor_attr =
+	    to_sensor_dev_attr_2(attr);
+	int nr = sensor_attr->nr;
+	struct w83793_data *data = w83793_update_device(dev);
+	u32 val = 0;
+
+	if (SETUP_PWM_DEFAULT == nr) {
+		val = (data->pwm_default & 0x3f) << 2;
+	} else if (SETUP_PWM_UPTIME == nr) {
+		val = TIME_FROM_REG(data->pwm_uptime);
+	} else if (SETUP_PWM_DOWNTIME == nr) {
+		val = TIME_FROM_REG(data->pwm_downtime);
+	} else if (SETUP_TEMP_CRITICAL == nr) {
+		val = TEMP_FROM_REG(data->temp_critical & 0x7f);
+	}
+
+	return sprintf(buf, "%d\n", val);
+}
+
+static ssize_t
+store_sf_setup(struct device *dev, struct device_attribute *attr,
+	       const char *buf, size_t count)
+{
+	struct sensor_device_attribute_2 *sensor_attr =
+	    to_sensor_dev_attr_2(attr);
+	int nr = sensor_attr->nr;
+	struct i2c_client *client = to_i2c_client(dev);
+	struct w83793_data *data = i2c_get_clientdata(client);
+
+	mutex_lock(&data->update_lock);
+	if (SETUP_PWM_DEFAULT == nr) {
+		data->pwm_default =
+		    w83793_read_value(client, W83793_REG_PWM_DEFAULT) & 0xc0;
+		data->pwm_default |= SENSORS_LIMIT(simple_strtoul(buf, NULL,
+								  10),
+						   0, 0xff) >> 2;
+		w83793_write_value(client, W83793_REG_PWM_DEFAULT,
+							data->pwm_default);
+	} else if (SETUP_PWM_UPTIME == nr) {
+		data->pwm_uptime = TIME_TO_REG(simple_strtoul(buf, NULL, 10));
+		data->pwm_uptime += data->pwm_uptime == 0 ? 1 : 0;
+		w83793_write_value(client, W83793_REG_PWM_UPTIME,
+							data->pwm_uptime);
+	} else if (SETUP_PWM_DOWNTIME == nr) {
+		data->pwm_downtime = TIME_TO_REG(simple_strtoul(buf, NULL, 10));
+		data->pwm_downtime += data->pwm_downtime == 0 ? 1 : 0;
+		w83793_write_value(client, W83793_REG_PWM_DOWNTIME,
+							data->pwm_downtime);
+	} else {		/* SETUP_TEMP_CRITICAL */
+		data->temp_critical =
+		    w83793_read_value(client, W83793_REG_TEMP_CRITICAL) & 0x80;
+		data->temp_critical |= TEMP_TO_REG(simple_strtol(buf, NULL, 10),
+						   0, 0x7f);
+		w83793_write_value(client, W83793_REG_TEMP_CRITICAL,
+							data->temp_critical);
+	}
+
+	mutex_unlock(&data->update_lock);
+	return count;
+}
+
+/*
+	Temp SmartFan control
+	TEMP_FAN_MAP
+	Temp channel control which pwm fan, bitfield, bit 0 indicate pwm1...
+	It's possible two or more temp channels control the same fan, w83793
+	always prefers to pick the most critical request and applies it to
+	the related Fan.
+	It's possible one fan is not in any mapping of 6 temp channels, this
+	means the fan is manual mode
+
+	TEMP_PWM_ENABLE
+	Each temp channel has its own SmartFan mode, and temp channel
+	control	fans that are set by TEMP_FAN_MAP
+	0:	SmartFanII mode
+	1:	Thermal Cruise Mode
+
+	TEMP_CRUISE
+	Target temperature in thermal cruise mode, w83793 will try to turn
+	fan speed to keep the temperature of target device around this
+	temperature.
+
+	TEMP_TOLERANCE
+	If Temp higher or lower than target with this tolerance, w83793
+	will take actions to speed up or slow down the fan to keep the
+	temperature within the tolerance range.
+*/
+
+#define TEMP_FAN_MAP			0
+#define TEMP_PWM_ENABLE			1
+#define TEMP_CRUISE			2
+#define TEMP_TOLERANCE			3
+static ssize_t
+show_sf_ctrl(struct device *dev, struct device_attribute *attr, char *buf)
+{
+	struct sensor_device_attribute_2 *sensor_attr =
+	    to_sensor_dev_attr_2(attr);
+	int nr = sensor_attr->nr;
+	int index = sensor_attr->index;
+	struct w83793_data *data = w83793_update_device(dev);
+	u32 val;
+
+	if (TEMP_FAN_MAP == nr) {
+		val = data->temp_fan_map[index];
+	} else if (TEMP_PWM_ENABLE == nr) {
+		/* +2 to transfrom into 2 and 3 to conform with sysfs intf */
+		val = ((data->pwm_enable >> index) & 0x01) + 2;
+	} else if (TEMP_CRUISE == nr) {
+		val = TEMP_FROM_REG(data->temp_cruise[index] & 0x7f);
+	} else {		/* TEMP_TOLERANCE */
+		val = data->tolerance[index >> 1] >> ((index & 0x01) ? 4 : 0);
+		val = TEMP_FROM_REG(val & 0x0f);
+	}
+	return sprintf(buf, "%d\n", val);
+}
+
+static ssize_t
+store_sf_ctrl(struct device *dev, struct device_attribute *attr,
+	      const char *buf, size_t count)
+{
+	struct sensor_device_attribute_2 *sensor_attr =
+	    to_sensor_dev_attr_2(attr);
+	int nr = sensor_attr->nr;
+	int index = sensor_attr->index;
+	struct i2c_client *client = to_i2c_client(dev);
+	struct w83793_data *data = i2c_get_clientdata(client);
+	u32 val;
+
+	mutex_lock(&data->update_lock);
+	if (TEMP_FAN_MAP == nr) {
+		val = simple_strtoul(buf, NULL, 10) & 0xff;
+		w83793_write_value(client, W83793_REG_TEMP_FAN_MAP(index), val);
+		data->temp_fan_map[index] = val;
+	} else if (TEMP_PWM_ENABLE == nr) {
+		val = simple_strtoul(buf, NULL, 10);
+		if (2 == val || 3 == val) {
+			data->pwm_enable =
+			    w83793_read_value(client, W83793_REG_PWM_ENABLE);
+			if (val - 2)
+				data->pwm_enable |= 1 << index;
+			else
+				data->pwm_enable &= ~(1 << index);
+			w83793_write_value(client, W83793_REG_PWM_ENABLE,
+							data->pwm_enable);
+		} else {
+			mutex_unlock(&data->update_lock);
+			return -EINVAL;
+		}
+	} else if (TEMP_CRUISE == nr) {
+		data->temp_cruise[index] =
+		    w83793_read_value(client, W83793_REG_TEMP_CRUISE(index));
+		val = TEMP_TO_REG(simple_strtol(buf, NULL, 10), 0, 0x7f);
+		data->temp_cruise[index] &= 0x80;
+		data->temp_cruise[index] |= val;
+
+		w83793_write_value(client, W83793_REG_TEMP_CRUISE(index),
+						data->temp_cruise[index]);
+	} else {		/* TEMP_TOLERANCE */
+		int i = index >> 1;
+		u8 shift = (index & 0x01) ? 4 : 0;
+		data->tolerance[i] =
+		    w83793_read_value(client, W83793_REG_TEMP_TOL(i));
+
+		val = TEMP_TO_REG(simple_strtol(buf, NULL, 10), 0, 0x0f);
+		data->tolerance[i] &= ~(0x0f << shift);
+		data->tolerance[i] |= val << shift;
+		w83793_write_value(client, W83793_REG_TEMP_TOL(i),
+							data->tolerance[i]);
+	}
+
+	mutex_unlock(&data->update_lock);
+	return count;
+}
+
+static ssize_t
+show_sf2_pwm(struct device *dev, struct device_attribute *attr, char *buf)
+{
+	struct sensor_device_attribute_2 *sensor_attr =
+	    to_sensor_dev_attr_2(attr);
+	int nr = sensor_attr->nr;
+	int index = sensor_attr->index;
+	struct w83793_data *data = w83793_update_device(dev);
+
+	return sprintf(buf, "%d\n", (data->sf2_pwm[index][nr] & 0x3f) << 2);
+}
+
+static ssize_t
+store_sf2_pwm(struct device *dev, struct device_attribute *attr,
+	      const char *buf, size_t count)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct w83793_data *data = i2c_get_clientdata(client);
+	struct sensor_device_attribute_2 *sensor_attr =
+	    to_sensor_dev_attr_2(attr);
+	int nr = sensor_attr->nr;
+	int index = sensor_attr->index;
+	u8 val = SENSORS_LIMIT(simple_strtoul(buf, NULL, 10), 0, 0xff) >> 2;
+
+	mutex_lock(&data->update_lock);
+	data->sf2_pwm[index][nr] =
+	    w83793_read_value(client, W83793_REG_SF2_PWM(index, nr)) & 0xc0;
+	data->sf2_pwm[index][nr] |= val;
+	w83793_write_value(client, W83793_REG_SF2_PWM(index, nr),
+						data->sf2_pwm[index][nr]);
+	mutex_unlock(&data->update_lock);
+	return count;
+}
+
+static ssize_t
+show_sf2_temp(struct device *dev, struct device_attribute *attr, char *buf)
+{
+	struct sensor_device_attribute_2 *sensor_attr =
+	    to_sensor_dev_attr_2(attr);
+	int nr = sensor_attr->nr;
+	int index = sensor_attr->index;
+	struct w83793_data *data = w83793_update_device(dev);
+
+	return sprintf(buf, "%ld\n",
+		       TEMP_FROM_REG(data->sf2_temp[index][nr] & 0x7f));
+}
+
+static ssize_t
+store_sf2_temp(struct device *dev, struct device_attribute *attr,
+	       const char *buf, size_t count)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct w83793_data *data = i2c_get_clientdata(client);
+	struct sensor_device_attribute_2 *sensor_attr =
+	    to_sensor_dev_attr_2(attr);
+	int nr = sensor_attr->nr;
+	int index = sensor_attr->index;
+	u8 val = TEMP_TO_REG(simple_strtol(buf, NULL, 10), 0, 0x7f);
+
+	mutex_lock(&data->update_lock);
+	data->sf2_temp[index][nr] =
+	    w83793_read_value(client, W83793_REG_SF2_TEMP(index, nr)) & 0x80;
+	data->sf2_temp[index][nr] |= val;
+	w83793_write_value(client, W83793_REG_SF2_TEMP(index, nr),
+					     data->sf2_temp[index][nr]);
+	mutex_unlock(&data->update_lock);
+	return count;
+}
+
+/* only Vcore A/B and Vtt have additional 2 bits precision */
+static ssize_t
+show_in(struct device *dev, struct device_attribute *attr, char *buf)
+{
+	struct sensor_device_attribute_2 *sensor_attr =
+	    to_sensor_dev_attr_2(attr);
+	int nr = sensor_attr->nr;
+	int index = sensor_attr->index;
+	struct w83793_data *data = w83793_update_device(dev);
+	u16 val = data->in[index][nr];
+
+	if (index < 3) {
+		val <<= 2;
+		val += (data->in_low_bits[nr] >> (index * 2)) & 0x3;
+	}
+	return sprintf(buf, "%d\n", val * scale_in[index]);
+}
+
+static ssize_t
+store_in(struct device *dev, struct device_attribute *attr,
+	 const char *buf, size_t count)
+{
+	struct sensor_device_attribute_2 *sensor_attr =
+	    to_sensor_dev_attr_2(attr);
+	int nr = sensor_attr->nr;
+	int index = sensor_attr->index;
+	struct i2c_client *client = to_i2c_client(dev);
+	struct w83793_data *data = i2c_get_clientdata(client);
+	u32 val;
+
+	val =
+	    (simple_strtoul(buf, NULL, 10) +
+	     scale_in[index] / 2) / scale_in[index];
+	mutex_lock(&data->update_lock);
+	if (index > 2) {
+		val = SENSORS_LIMIT(val, 0, 255);
+	} else {
+		val = SENSORS_LIMIT(val, 0, 0x3FF);
+		data->in_low_bits[nr] =
+		    w83793_read_value(client, W83793_REG_IN_LOW_BITS[nr]);
+		data->in_low_bits[nr] &= ~(0x03 << (2 * index));
+		data->in_low_bits[nr] |= (val & 0x03) << (2 * index);
+		w83793_write_value(client, W83793_REG_IN_LOW_BITS[nr],
+						     data->in_low_bits[nr]);
+		val >>= 2;
+	}
+	data->in[index][nr] = val;
+	w83793_write_value(client, W83793_REG_IN[index][nr],
+							data->in[index][nr]);
+	mutex_unlock(&data->update_lock);
+	return count;
+}
+
+#define NOT_USED			-1
+
+#define SENSOR_ATTR_IN(index)						\
+	SENSOR_ATTR_2(in##index##_input, S_IRUGO, show_in, NULL,	\
+		IN_READ, index),					\
+	SENSOR_ATTR_2(in##index##_max, S_IRUGO | S_IWUSR, show_in,	\
+		store_in, IN_MAX, index),				\
+	SENSOR_ATTR_2(in##index##_min, S_IRUGO | S_IWUSR, show_in,	\
+		store_in, IN_LOW, index),				\
+	SENSOR_ATTR_2(in##index##_alarm, S_IRUGO, show_alarm_beep,	\
+		NULL, ALARM_STATUS, index + ((index > 2) ? 1 : 0)),	\
+	SENSOR_ATTR_2(in##index##_beep, S_IWUSR | S_IRUGO,		\
+		show_alarm_beep, store_beep, BEEP_ENABLE,		\
+		index + ((index > 2) ? 1 : 0))
+
+#define SENSOR_ATTR_FAN(index)						\
+	SENSOR_ATTR_2(fan##index##_alarm, S_IRUGO, show_alarm_beep,	\
+		NULL, ALARM_STATUS, index + 17),			\
+	SENSOR_ATTR_2(fan##index##_beep, S_IWUSR | S_IRUGO,		\
+		show_alarm_beep, store_beep, BEEP_ENABLE, index + 17),	\
+	SENSOR_ATTR_2(fan##index##_input, S_IRUGO, show_fan,		\
+		NULL, FAN_INPUT, index - 1),				\
+	SENSOR_ATTR_2(fan##index##_min, S_IWUSR | S_IRUGO,		\
+		show_fan, store_fan_min, FAN_MIN, index - 1)
+
+#define SENSOR_ATTR_PWM(index)						\
+	SENSOR_ATTR_2(pwm##index, S_IWUSR | S_IRUGO, show_pwm,		\
+		store_pwm, PWM_DUTY, index - 1),			\
+	SENSOR_ATTR_2(pwm##index##_nonstop, S_IWUSR | S_IRUGO,		\
+		show_pwm, store_pwm, PWM_NONSTOP, index - 1),		\
+	SENSOR_ATTR_2(pwm##index##_start, S_IWUSR | S_IRUGO,		\
+		show_pwm, store_pwm, PWM_START, index - 1),		\
+	SENSOR_ATTR_2(pwm##index##_stop_time, S_IWUSR | S_IRUGO,	\
+		show_pwm, store_pwm, PWM_STOP_TIME, index - 1)
+
+#define SENSOR_ATTR_TEMP(index)						\
+	SENSOR_ATTR_2(temp##index##_type, S_IRUGO | S_IWUSR,		\
+		show_temp_mode, store_temp_mode, NOT_USED, index - 1),	\
+	SENSOR_ATTR_2(temp##index##_input, S_IRUGO, show_temp,		\
+		NULL, TEMP_READ, index - 1),				\
+	SENSOR_ATTR_2(temp##index##_max, S_IRUGO | S_IWUSR, show_temp,	\
+		store_temp, TEMP_CRIT, index - 1),			\
+	SENSOR_ATTR_2(temp##index##_max_hyst, S_IRUGO | S_IWUSR,	\
+		show_temp, store_temp, TEMP_CRIT_HYST, index - 1),	\
+	SENSOR_ATTR_2(temp##index##_warn, S_IRUGO | S_IWUSR, show_temp,	\
+		store_temp, TEMP_WARN, index - 1),			\
+	SENSOR_ATTR_2(temp##index##_warn_hyst, S_IRUGO | S_IWUSR,	\
+		show_temp, store_temp, TEMP_WARN_HYST, index - 1),	\
+	SENSOR_ATTR_2(temp##index##_alarm, S_IRUGO,			\
+		show_alarm_beep, NULL, ALARM_STATUS, index + 11),	\
+	SENSOR_ATTR_2(temp##index##_beep, S_IWUSR | S_IRUGO,		\
+		show_alarm_beep, store_beep, BEEP_ENABLE, index + 11),	\
+	SENSOR_ATTR_2(temp##index##_auto_channels_pwm,			\
+		S_IRUGO | S_IWUSR, show_sf_ctrl, store_sf_ctrl,		\
+		TEMP_FAN_MAP, index - 1),				\
+	SENSOR_ATTR_2(temp##index##_pwm_enable, S_IWUSR | S_IRUGO,	\
+		show_sf_ctrl, store_sf_ctrl, TEMP_PWM_ENABLE,		\
+		index - 1),						\
+	SENSOR_ATTR_2(thermal_cruise##index, S_IRUGO | S_IWUSR,		\
+		show_sf_ctrl, store_sf_ctrl, TEMP_CRUISE, index - 1),	\
+	SENSOR_ATTR_2(tolerance##index, S_IRUGO | S_IWUSR, show_sf_ctrl,\
+		store_sf_ctrl, TEMP_TOLERANCE, index - 1),		\
+	SENSOR_ATTR_2(temp##index##_auto_point1_pwm, S_IRUGO | S_IWUSR, \
+		show_sf2_pwm, store_sf2_pwm, 0, index - 1),		\
+	SENSOR_ATTR_2(temp##index##_auto_point2_pwm, S_IRUGO | S_IWUSR, \
+		show_sf2_pwm, store_sf2_pwm, 1, index - 1),		\
+	SENSOR_ATTR_2(temp##index##_auto_point3_pwm, S_IRUGO | S_IWUSR, \
+		show_sf2_pwm, store_sf2_pwm, 2, index - 1),		\
+	SENSOR_ATTR_2(temp##index##_auto_point4_pwm, S_IRUGO | S_IWUSR, \
+		show_sf2_pwm, store_sf2_pwm, 3, index - 1),		\
+	SENSOR_ATTR_2(temp##index##_auto_point5_pwm, S_IRUGO | S_IWUSR, \
+		show_sf2_pwm, store_sf2_pwm, 4, index - 1),		\
+	SENSOR_ATTR_2(temp##index##_auto_point6_pwm, S_IRUGO | S_IWUSR, \
+		show_sf2_pwm, store_sf2_pwm, 5, index - 1),		\
+	SENSOR_ATTR_2(temp##index##_auto_point7_pwm, S_IRUGO | S_IWUSR, \
+		show_sf2_pwm, store_sf2_pwm, 6, index - 1),		\
+	SENSOR_ATTR_2(temp##index##_auto_point1_temp, S_IRUGO | S_IWUSR,\
+		show_sf2_temp, store_sf2_temp, 0, index - 1),		\
+	SENSOR_ATTR_2(temp##index##_auto_point2_temp, S_IRUGO | S_IWUSR,\
+		show_sf2_temp, store_sf2_temp, 1, index - 1),		\
+	SENSOR_ATTR_2(temp##index##_auto_point3_temp, S_IRUGO | S_IWUSR,\
+		show_sf2_temp, store_sf2_temp, 2, index - 1),		\
+	SENSOR_ATTR_2(temp##index##_auto_point4_temp, S_IRUGO | S_IWUSR,\
+		show_sf2_temp, store_sf2_temp, 3, index - 1),		\
+	SENSOR_ATTR_2(temp##index##_auto_point5_temp, S_IRUGO | S_IWUSR,\
+		show_sf2_temp, store_sf2_temp, 4, index - 1),		\
+	SENSOR_ATTR_2(temp##index##_auto_point6_temp, S_IRUGO | S_IWUSR,\
+		show_sf2_temp, store_sf2_temp, 5, index - 1),		\
+	SENSOR_ATTR_2(temp##index##_auto_point7_temp, S_IRUGO | S_IWUSR,\
+		show_sf2_temp, store_sf2_temp, 6, index - 1)
+
+static struct sensor_device_attribute_2 w83793_sensor_attr_2[] = {
+	SENSOR_ATTR_IN(0),
+	SENSOR_ATTR_IN(1),
+	SENSOR_ATTR_IN(2),
+	SENSOR_ATTR_IN(3),
+	SENSOR_ATTR_IN(4),
+	SENSOR_ATTR_IN(5),
+	SENSOR_ATTR_IN(6),
+	SENSOR_ATTR_IN(7),
+	SENSOR_ATTR_IN(8),
+	SENSOR_ATTR_IN(9),
+	SENSOR_ATTR_TEMP(1),
+	SENSOR_ATTR_TEMP(2),
+	SENSOR_ATTR_TEMP(3),
+	SENSOR_ATTR_TEMP(4),
+	SENSOR_ATTR_TEMP(5),
+	SENSOR_ATTR_TEMP(6),
+	SENSOR_ATTR_FAN(1),
+	SENSOR_ATTR_FAN(2),
+	SENSOR_ATTR_FAN(3),
+	SENSOR_ATTR_FAN(4),
+	SENSOR_ATTR_FAN(5),
+	SENSOR_ATTR_PWM(1),
+	SENSOR_ATTR_PWM(2),
+	SENSOR_ATTR_PWM(3),
+};
+
+/* Fan6-Fan12 */
+static struct sensor_device_attribute_2 w83793_left_fan[] = {
+	SENSOR_ATTR_FAN(6),
+	SENSOR_ATTR_FAN(7),
+	SENSOR_ATTR_FAN(8),
+	SENSOR_ATTR_FAN(9),
+	SENSOR_ATTR_FAN(10),
+	SENSOR_ATTR_FAN(11),
+	SENSOR_ATTR_FAN(12),
+};
+
+/* Pwm4-Pwm8 */
+static struct sensor_device_attribute_2 w83793_left_pwm[] = {
+	SENSOR_ATTR_PWM(4),
+	SENSOR_ATTR_PWM(5),
+	SENSOR_ATTR_PWM(6),
+	SENSOR_ATTR_PWM(7),
+	SENSOR_ATTR_PWM(8),
+};
+
+static struct sensor_device_attribute_2 sda_single_files[] = {
+	SENSOR_ATTR_2(cpu0_vid, S_IRUGO, show_vid, NULL, NOT_USED, 0),
+	SENSOR_ATTR_2(cpu1_vid, S_IRUGO, show_vid, NULL, NOT_USED, 1),
+	SENSOR_ATTR_2(vrm, S_IWUSR | S_IRUGO, show_vrm, store_vrm,
+		      NOT_USED, NOT_USED),
+	SENSOR_ATTR_2(chassis, S_IWUSR | S_IRUGO, show_alarm_beep,
+		      store_chassis_clear, ALARM_STATUS, 30),
+	SENSOR_ATTR_2(beep_enable, S_IWUSR | S_IRUGO, show_beep_enable,
+		      store_beep_enable, NOT_USED, NOT_USED),
+	SENSOR_ATTR_2(pwm_default, S_IWUSR | S_IRUGO, show_sf_setup,
+		      store_sf_setup, SETUP_PWM_DEFAULT, NOT_USED),
+	SENSOR_ATTR_2(pwm_uptime, S_IWUSR | S_IRUGO, show_sf_setup,
+		      store_sf_setup, SETUP_PWM_UPTIME, NOT_USED),
+	SENSOR_ATTR_2(pwm_downtime, S_IWUSR | S_IRUGO, show_sf_setup,
+		      store_sf_setup, SETUP_PWM_DOWNTIME, NOT_USED),
+	SENSOR_ATTR_2(temp_critical, S_IWUSR | S_IRUGO, show_sf_setup,
+		      store_sf_setup, SETUP_TEMP_CRITICAL, NOT_USED),
+};
+
+static void w83793_init_client(struct i2c_client *client)
+{
+	if (reset) {
+		w83793_write_value(client, W83793_REG_CONFIG, 0x80);
+	}
+
+	/* Start monitoring */
+	w83793_write_value(client, W83793_REG_CONFIG,
+			   w83793_read_value(client, W83793_REG_CONFIG) | 0x01);
+
+}
+
+static int w83793_attach_adapter(struct i2c_adapter *adapter)
+{
+	if (!(adapter->class & I2C_CLASS_HWMON))
+		return 0;
+	return i2c_probe(adapter, &addr_data, w83793_detect);
+}
+
+static int w83793_detach_client(struct i2c_client *client)
+{
+	struct w83793_data *data = i2c_get_clientdata(client);
+	struct device *dev = &client->dev;
+	int err, i;
+
+	/* main client */
+	if (data) {
+		hwmon_device_unregister(data->class_dev);
+
+		for (i = 0; i < ARRAY_SIZE(w83793_sensor_attr_2); i++)
+			device_remove_file(dev,
+					   &w83793_sensor_attr_2[i].dev_attr);
+
+		for (i = 0; i < ARRAY_SIZE(sda_single_files); i++)
+			device_remove_file(dev, &sda_single_files[i].dev_attr);
+
+		for (i = 0; i < ARRAY_SIZE(w83793_left_fan); i++)
+			device_remove_file(dev, &w83793_left_fan[i].dev_attr);
+
+		for (i = 0; i < ARRAY_SIZE(w83793_left_pwm); i++)
+			device_remove_file(dev, &w83793_left_pwm[i].dev_attr);
+	}
+
+	if ((err = i2c_detach_client(client)))
+		return err;
+
+	/* main client */
+	if (data)
+		kfree(data);
+	/* subclient */
+	else
+		kfree(client);
+
+	return 0;
+}
+
+static int
+w83793_create_subclient(struct i2c_adapter *adapter,
+			struct i2c_client *client, int addr,
+			struct i2c_client **sub_cli)
+{
+	int err = 0;
+	struct i2c_client *sub_client;
+
+	(*sub_cli) = sub_client =
+	    kzalloc(sizeof(struct i2c_client), GFP_KERNEL);
+	if (!(sub_client)) {
+		return -ENOMEM;
+	}
+	sub_client->addr = 0x48 + addr;
+	i2c_set_clientdata(sub_client, NULL);
+	sub_client->adapter = adapter;
+	sub_client->driver = &w83793_driver;
+	strlcpy(sub_client->name, "w83793 subclient", I2C_NAME_SIZE);
+	if ((err = i2c_attach_client(sub_client))) {
+		dev_err(&client->dev, "subclient registration "
+			"at address 0x%x failed\n", sub_client->addr);
+		kfree(sub_client);
+	}
+	return err;
+}
+
+static int
+w83793_detect_subclients(struct i2c_adapter *adapter, int address,
+			 int kind, struct i2c_client *client)
+{
+	int i, id, err;
+	u8 tmp;
+	struct w83793_data *data = i2c_get_clientdata(client);
+
+	id = i2c_adapter_id(adapter);
+	if (force_subclients[0] == id && force_subclients[1] == address) {
+		for (i = 2; i <= 3; i++) {
+			if (force_subclients[i] < 0x48
+			    || force_subclients[i] > 0x4f) {
+				dev_err(&client->dev,
+					"invalid subclient "
+					"address %d; must be 0x48-0x4f\n",
+					force_subclients[i]);
+				err = -EINVAL;
+				goto ERROR_SC_0;
+			}
+		}
+		w83793_write_value(client, W83793_REG_I2C_SUBADDR,
+				   (force_subclients[2] & 0x07) |
+				   ((force_subclients[3] & 0x07) << 4));
+	}
+
+	tmp = w83793_read_value(client, W83793_REG_I2C_SUBADDR);
+	if (!(tmp & 0x08)) {
+		err =
+		    w83793_create_subclient(adapter, client, tmp & 0x7,
+					    &data->lm75[0]);
+		if (err < 0)
+			goto ERROR_SC_0;
+	}
+	if (!(tmp & 0x80)) {
+		if ((data->lm75[0] != NULL)
+		    && ((tmp & 0x7) == ((tmp >> 4) & 0x7))) {
+			dev_err(&client->dev,
+				"duplicate addresses 0x%x, "
+				"use force_subclients\n", data->lm75[0]->addr);
+			err = -ENODEV;
+			goto ERROR_SC_1;
+		}
+		err = w83793_create_subclient(adapter, client,
+					      (tmp >> 4) & 0x7, &data->lm75[1]);
+		if (err < 0)
+			goto ERROR_SC_1;
+	}
+
+	return 0;
+
+	/* Undo inits in case of errors */
+
+ERROR_SC_1:
+	if (data->lm75[0] != NULL) {
+		i2c_detach_client(data->lm75[0]);
+		kfree(data->lm75[0]);
+	}
+ERROR_SC_0:
+	return err;
+}
+
+static int w83793_detect(struct i2c_adapter *adapter, int address, int kind)
+{
+	int i;
+	u8 tmp, val;
+	struct i2c_client *client;
+	struct device *dev;
+	struct w83793_data *data;
+	int files_fan = ARRAY_SIZE(w83793_left_fan) / 7;
+	int files_pwm = ARRAY_SIZE(w83793_left_pwm) / 5;
+	int err = 0;
+
+	if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) {
+		goto exit;
+	}
+
+	/* OK. For now, we presume we have a valid client. We now create the
+	   client structure, even though we cannot fill it completely yet.
+	   But it allows us to access w83793_{read,write}_value. */
+
+	if (!(data = kzalloc(sizeof(struct w83793_data), GFP_KERNEL))) {
+		err = -ENOMEM;
+		goto exit;
+	}
+
+	client = &data->client;
+	dev = &client->dev;
+	i2c_set_clientdata(client, data);
+	client->addr = address;
+	client->adapter = adapter;
+	client->driver = &w83793_driver;
+
+	data->bank = i2c_smbus_read_byte_data(client, W83793_REG_BANKSEL);
+
+	/* Now, we do the remaining detection. */
+	if (kind < 0) {
+		tmp = data->bank & 0x80 ? 0x5c : 0xa3;
+		/* Check Winbond vendor ID */
+		if (tmp != i2c_smbus_read_byte_data(client,
+							W83793_REG_VENDORID)) {
+			pr_debug("w83793: Detection failed at check "
+				 "vendor id\n");
+			err = -ENODEV;
+			goto free_mem;
+		}
+
+		/* If Winbond chip, address of chip and W83793_REG_I2C_ADDR
+		   should match */
+		if ((data->bank & 0x07) == 0
+		 && i2c_smbus_read_byte_data(client, W83793_REG_I2C_ADDR) !=
+		    (address << 1)) {
+			pr_debug("w83793: Detection failed at check "
+				 "i2c addr\n");
+			err = -ENODEV;
+			goto free_mem;
+		}
+
+	}
+
+	/* We have either had a force parameter, or we have already detected the
+	   Winbond. Determine the chip type now */
+
+	if (kind <= 0) {
+		if (0x7b == w83793_read_value(client, W83793_REG_CHIPID)) {
+			kind = w83793;
+		} else {
+			if (kind == 0)
+				dev_warn(&adapter->dev, "w83793: Ignoring "
+					 "'force' parameter for unknown chip "
+					 "at address 0x%02x\n", address);
+			err = -ENODEV;
+			goto free_mem;
+		}
+	}
+
+	/* Fill in the remaining client fields and put into the global list */
+	strlcpy(client->name, "w83793", I2C_NAME_SIZE);
+
+	mutex_init(&data->update_lock);
+
+	/* Tell the I2C layer a new client has arrived */
+	if ((err = i2c_attach_client(client)))
+		goto free_mem;
+
+	if ((err = w83793_detect_subclients(adapter, address, kind, client)))
+		goto detach_client;
+
+	/* Initialize the chip */
+	w83793_init_client(client);
+
+	data->vrm = vid_which_vrm();
+	/*
+	   Only fan 1-5 has their own input pins,
+	   Pwm 1-3 has their own pins
+	 */
+	data->has_fan = 0x1f;
+	data->has_pwm = 0x07;
+	tmp = w83793_read_value(client, W83793_REG_MFC);
+	val = w83793_read_value(client, W83793_REG_FANIN_CTRL);
+
+	/* check the function of pins 49-56 */
+	if (!(tmp & 0x80)) {
+		data->has_pwm |= 0x18;	/* pwm 4,5 */
+		if (val & 0x01) {	/* fan 6 */
+			data->has_fan |= 0x20;
+			data->has_pwm |= 0x20;
+		}
+		if (val & 0x02) {	/* fan 7 */
+			data->has_fan |= 0x40;
+			data->has_pwm |= 0x40;
+		}
+		if (!(tmp & 0x40) && (val & 0x04)) {	/* fan 8 */
+			data->has_fan |= 0x80;
+			data->has_pwm |= 0x80;
+		}
+	}
+
+	if (0x08 == (tmp & 0x0c)) {
+		if (val & 0x08)	/* fan 9 */
+			data->has_fan |= 0x100;
+		if (val & 0x10)	/* fan 10 */
+			data->has_fan |= 0x200;
+	}
+
+	if (0x20 == (tmp & 0x30)) {
+		if (val & 0x20)	/* fan 11 */
+			data->has_fan |= 0x400;
+		if (val & 0x40)	/* fan 12 */
+			data->has_fan |= 0x800;
+	}
+
+	if ((tmp & 0x01) && (val & 0x04)) {	/* fan 8, second location */
+		data->has_fan |= 0x80;
+		data->has_pwm |= 0x80;
+	}
+
+	/* Register sysfs hooks */
+	for (i = 0; i < ARRAY_SIZE(w83793_sensor_attr_2); i++) {
+		err = device_create_file(dev,
+					 &w83793_sensor_attr_2[i].dev_attr);
+		if (err)
+			goto exit_remove;
+	}
+
+	for (i = 0; i < ARRAY_SIZE(sda_single_files); i++) {
+		err = device_create_file(dev, &sda_single_files[i].dev_attr);
+		if (err)
+			goto exit_remove;
+
+	}
+
+	for (i = 5; i < 12; i++) {
+		int j;
+		if (!(data->has_fan & (1 << i)))
+			continue;
+		for (j = 0; j < files_fan; j++) {
+			err = device_create_file(dev,
+					   &w83793_left_fan[(i - 5) * files_fan
+								+ j].dev_attr);
+			if (err)
+				goto exit_remove;
+		}
+	}
+
+	for (i = 3; i < 8; i++) {
+		int j;
+		if (!(data->has_pwm & (1 << i)))
+			continue;
+		for (j = 0; j < files_pwm; j++) {
+			err = device_create_file(dev,
+					   &w83793_left_pwm[(i - 3) * files_pwm
+								+ j].dev_attr);
+			if (err)
+				goto exit_remove;
+		}
+	}
+
+	data->class_dev = hwmon_device_register(dev);
+	if (IS_ERR(data->class_dev)) {
+		err = PTR_ERR(data->class_dev);
+		goto exit_remove;
+	}
+
+	return 0;
+
+	/* Unregister sysfs hooks */
+
+exit_remove:
+	for (i = 0; i < ARRAY_SIZE(w83793_sensor_attr_2); i++)
+		device_remove_file(dev, &w83793_sensor_attr_2[i].dev_attr);
+
+	for (i = 0; i < ARRAY_SIZE(sda_single_files); i++)
+		device_remove_file(dev, &sda_single_files[i].dev_attr);
+
+	for (i = 0; i < ARRAY_SIZE(w83793_left_fan); i++)
+		device_remove_file(dev, &w83793_left_fan[i].dev_attr);
+
+	for (i = 0; i < ARRAY_SIZE(w83793_left_pwm); i++)
+		device_remove_file(dev, &w83793_left_pwm[i].dev_attr);
+
+	if (data->lm75[0] != NULL) {
+		i2c_detach_client(data->lm75[0]);
+		kfree(data->lm75[0]);
+	}
+	if (data->lm75[1] != NULL) {
+		i2c_detach_client(data->lm75[1]);
+		kfree(data->lm75[1]);
+	}
+detach_client:
+	i2c_detach_client(client);
+free_mem:
+	kfree(data);
+exit:
+	return err;
+}
+
+static void w83793_update_nonvolatile(struct device *dev)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct w83793_data *data = i2c_get_clientdata(client);
+	int i, j;
+	/*
+	   They are somewhat "stable" registers, and to update them everytime
+	   takes so much time, it's just not worthy. Update them in a long
+	   interval to avoid exception.
+	 */
+	if (!(time_after(jiffies, data->last_nonvolatile + HZ * 300)
+	      || !data->valid))
+		return;
+	/* update voltage limits */
+	for (i = 1; i < 3; i++) {
+		for (j = 0; j < ARRAY_SIZE(data->in); j++) {
+			data->in[j][i] =
+			    w83793_read_value(client, W83793_REG_IN[j][i]);
+		}
+		data->in_low_bits[i] =
+		    w83793_read_value(client, W83793_REG_IN_LOW_BITS[i]);
+	}
+
+	for (i = 0; i < ARRAY_SIZE(data->fan_min); i++) {
+		/* Update the Fan measured value and limits */
+		if (!(data->has_fan & (1 << i))) {
+			continue;
+		}
+		data->fan_min[i] =
+		    w83793_read_value(client, W83793_REG_FAN_MIN(i)) << 8;
+		data->fan_min[i] |=
+		    w83793_read_value(client, W83793_REG_FAN_MIN(i) + 1);
+	}
+
+	for (i = 0; i < ARRAY_SIZE(data->temp_fan_map); i++) {
+		data->temp_fan_map[i] =
+		    w83793_read_value(client, W83793_REG_TEMP_FAN_MAP(i));
+		for (j = 1; j < 5; j++) {
+			data->temp[i][j] =
+			    w83793_read_value(client, W83793_REG_TEMP[i][j]);
+		}
+		data->temp_cruise[i] =
+		    w83793_read_value(client, W83793_REG_TEMP_CRUISE(i));
+		for (j = 0; j < 7; j++) {
+			data->sf2_pwm[i][j] =
+			    w83793_read_value(client, W83793_REG_SF2_PWM(i, j));
+			data->sf2_temp[i][j] =
+			    w83793_read_value(client,
+					      W83793_REG_SF2_TEMP(i, j));
+		}
+	}
+
+	for (i = 0; i < ARRAY_SIZE(data->temp_mode); i++)
+		data->temp_mode[i] =
+		    w83793_read_value(client, W83793_REG_TEMP_MODE[i]);
+
+	for (i = 0; i < ARRAY_SIZE(data->tolerance); i++) {
+		data->tolerance[i] =
+		    w83793_read_value(client, W83793_REG_TEMP_TOL(i));
+	}
+
+	for (i = 0; i < ARRAY_SIZE(data->pwm); i++) {
+		if (!(data->has_pwm & (1 << i)))
+			continue;
+		data->pwm[i][PWM_NONSTOP] =
+		    w83793_read_value(client, W83793_REG_PWM(i, PWM_NONSTOP));
+		data->pwm[i][PWM_START] =
+		    w83793_read_value(client, W83793_REG_PWM(i, PWM_START));
+		data->pwm_stop_time[i] =
+		    w83793_read_value(client, W83793_REG_PWM_STOP_TIME(i));
+	}
+
+	data->pwm_default = w83793_read_value(client, W83793_REG_PWM_DEFAULT);
+	data->pwm_enable = w83793_read_value(client, W83793_REG_PWM_ENABLE);
+	data->pwm_uptime = w83793_read_value(client, W83793_REG_PWM_UPTIME);
+	data->pwm_downtime = w83793_read_value(client, W83793_REG_PWM_DOWNTIME);
+	data->temp_critical =
+	    w83793_read_value(client, W83793_REG_TEMP_CRITICAL);
+	data->beep_enable = w83793_read_value(client, W83793_REG_OVT_BEEP);
+
+	for (i = 0; i < ARRAY_SIZE(data->beeps); i++) {
+		data->beeps[i] = w83793_read_value(client, W83793_REG_BEEP(i));
+	}
+
+	data->last_nonvolatile = jiffies;
+}
+
+static struct w83793_data *w83793_update_device(struct device *dev)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct w83793_data *data = i2c_get_clientdata(client);
+	int i;
+
+	mutex_lock(&data->update_lock);
+
+	if (!(time_after(jiffies, data->last_updated + HZ * 2)
+	      || !data->valid))
+		goto END;
+
+	/* Update the voltages measured value and limits */
+	for (i = 0; i < ARRAY_SIZE(data->in); i++)
+		data->in[i][IN_READ] =
+		    w83793_read_value(client, W83793_REG_IN[i][IN_READ]);
+
+	data->in_low_bits[IN_READ] =
+	    w83793_read_value(client, W83793_REG_IN_LOW_BITS[IN_READ]);
+
+	for (i = 0; i < ARRAY_SIZE(data->fan); i++) {
+		if (!(data->has_fan & (1 << i))) {
+			continue;
+		}
+		data->fan[i] =
+		    w83793_read_value(client, W83793_REG_FAN(i)) << 8;
+		data->fan[i] |=
+		    w83793_read_value(client, W83793_REG_FAN(i) + 1);
+	}
+
+	for (i = 0; i < ARRAY_SIZE(data->temp); i++)
+		data->temp[i][TEMP_READ] =
+		    w83793_read_value(client, W83793_REG_TEMP[i][TEMP_READ]);
+
+	data->temp_low_bits =
+	    w83793_read_value(client, W83793_REG_TEMP_LOW_BITS);
+
+	for (i = 0; i < ARRAY_SIZE(data->pwm); i++) {
+		if (data->has_pwm & (1 << i))
+			data->pwm[i][PWM_DUTY] =
+			    w83793_read_value(client,
+					      W83793_REG_PWM(i, PWM_DUTY));
+	}
+
+	for (i = 0; i < ARRAY_SIZE(data->alarms); i++)
+		data->alarms[i] =
+		    w83793_read_value(client, W83793_REG_ALARM(i));
+	data->vid[0] = w83793_read_value(client, W83793_REG_VID_INA);
+	data->vid[1] = w83793_read_value(client, W83793_REG_VID_INB);
+	w83793_update_nonvolatile(dev);
+	data->last_updated = jiffies;
+	data->valid = 1;
+
+END:
+	mutex_unlock(&data->update_lock);
+	return data;
+}
+
+/* Ignore the possibility that somebody change bank outside the driver
+   Must be called with data->update_lock held, except during initialization */
+static u8 w83793_read_value(struct i2c_client *client, u16 reg)
+{
+	struct w83793_data *data = i2c_get_clientdata(client);
+	u8 res = 0xff;
+	u8 new_bank = reg >> 8;
+
+	new_bank |= data->bank & 0xfc;
+	if (data->bank != new_bank) {
+		if (i2c_smbus_write_byte_data
+		    (client, W83793_REG_BANKSEL, new_bank) >= 0)
+			data->bank = new_bank;
+		else {
+			dev_err(&client->dev,
+				"set bank to %d failed, fall back "
+				"to bank %d, read reg 0x%x error\n",
+				new_bank, data->bank, reg);
+			res = 0x0;	/* read 0x0 from the chip */
+			goto END;
+		}
+	}
+	res = i2c_smbus_read_byte_data(client, reg & 0xff);
+END:
+	return res;
+}
+
+/* Must be called with data->update_lock held, except during initialization */
+static int w83793_write_value(struct i2c_client *client, u16 reg, u8 value)
+{
+	struct w83793_data *data = i2c_get_clientdata(client);
+	int res;
+	u8 new_bank = reg >> 8;
+
+	new_bank |= data->bank & 0xfc;
+	if (data->bank != new_bank) {
+		if ((res = i2c_smbus_write_byte_data
+		    (client, W83793_REG_BANKSEL, new_bank)) >= 0)
+			data->bank = new_bank;
+		else {
+			dev_err(&client->dev,
+				"set bank to %d failed, fall back "
+				"to bank %d, write reg 0x%x error\n",
+				new_bank, data->bank, reg);
+			goto END;
+		}
+	}
+
+	res = i2c_smbus_write_byte_data(client, reg & 0xff, value);
+END:
+	return res;
+}
+
+static int __init sensors_w83793_init(void)
+{
+	return i2c_add_driver(&w83793_driver);
+}
+
+static void __exit sensors_w83793_exit(void)
+{
+	i2c_del_driver(&w83793_driver);
+}
+
+MODULE_AUTHOR("Yuan Mu");
+MODULE_DESCRIPTION("w83793 driver");
+MODULE_LICENSE("GPL");
+
+module_init(sensors_w83793_init);
+module_exit(sensors_w83793_exit);