diff --git a/Documentation/devicetree/bindings/serial/cirrus,clps711x-uart.txt b/Documentation/devicetree/bindings/serial/cirrus,clps711x-uart.txt
index 12f3cf8..caaeb25 100644
--- a/Documentation/devicetree/bindings/serial/cirrus,clps711x-uart.txt
+++ b/Documentation/devicetree/bindings/serial/cirrus,clps711x-uart.txt
@@ -8,7 +8,8 @@
 - syscon: Phandle to SYSCON node, which contain UART control bits.
 
 Optional properties:
-- uart-use-ms: Indicate the UART has modem signal (DCD, DSR, CTS).
+- {rts,cts,dtr,dsr,rng,dcd}-gpios: specify a GPIO for RTS/CTS/DTR/DSR/RI/DCD
+  line respectively.
 
 Note: Each UART port should have an alias correctly numbered
 in "aliases" node.
@@ -24,5 +25,7 @@
 		interrupts = <12 13>;
 		clocks = <&clks 11>;
 		syscon = <&syscon1>;
-		uart-use-ms;
+		cts-gpios = <&sysgpio 0 GPIO_ACTIVE_LOW>;
+		dsr-gpios = <&sysgpio 1 GPIO_ACTIVE_LOW>;
+		dcd-gpios = <&sysgpio 2 GPIO_ACTIVE_LOW>;
 	};
diff --git a/Documentation/devicetree/bindings/serial/mtk-uart.txt b/Documentation/devicetree/bindings/serial/mtk-uart.txt
new file mode 100644
index 0000000..48358a3
--- /dev/null
+++ b/Documentation/devicetree/bindings/serial/mtk-uart.txt
@@ -0,0 +1,22 @@
+* Mediatek Universal Asynchronous Receiver/Transmitter (UART)
+
+Required properties:
+- compatible should contain:
+  * "mediatek,mt6589-uart" for MT6589 compatible UARTS
+  * "mediatek,mt6582-uart" for MT6582 compatible UARTS
+  * "mediatek,mt6577-uart" for all compatible UARTS (MT6589, MT6582, MT6577)
+
+- reg: The base address of the UART register bank.
+
+- interrupts: A single interrupt specifier.
+
+- clocks: Clock driving the hardware.
+
+Example:
+
+	uart0: serial@11006000 {
+		compatible = "mediatek,mt6589-uart", "mediatek,mt6577-uart";
+		reg = <0x11006000 0x400>;
+		interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_LOW>;
+		clocks = <&uart_clk>;
+	};
diff --git a/Documentation/devicetree/bindings/serial/of-serial.txt b/Documentation/devicetree/bindings/serial/of-serial.txt
index 7705477..8c4fd03 100644
--- a/Documentation/devicetree/bindings/serial/of-serial.txt
+++ b/Documentation/devicetree/bindings/serial/of-serial.txt
@@ -14,6 +14,7 @@
 	- "altr,16550-FIFO32"
 	- "altr,16550-FIFO64"
 	- "altr,16550-FIFO128"
+	- "fsl,16550-FIFO64"
 	- "serial" if the port type is unknown.
 - reg : offset and length of the register set for the device.
 - interrupts : should contain uart interrupt.
@@ -37,7 +38,6 @@
 - auto-flow-control: one way to enable automatic flow control support. The
   driver is allowed to detect support for the capability even without this
   property.
-- has-hw-flow-control: the hardware has flow control capability.
 
 Example:
 
diff --git a/Documentation/devicetree/bindings/serial/via,vt8500-uart.txt b/Documentation/devicetree/bindings/serial/via,vt8500-uart.txt
deleted file mode 100644
index 5feef1e..0000000
--- a/Documentation/devicetree/bindings/serial/via,vt8500-uart.txt
+++ /dev/null
@@ -1,17 +0,0 @@
-VIA/Wondermedia VT8500 UART Controller
------------------------------------------------------
-
-Required properties:
-- compatible : "via,vt8500-uart"
-- reg : Should contain 1 register ranges(address and length)
-- interrupts : UART interrupt
-- clocks : phandle to the uart source clock (usually a 24Mhz fixed clock)
-
-Example:
-
-	uart@d8210000 {
-		compatible = "via,vt8500-uart";
-		reg = <0xd8210000 0x1040>;
-		interrupts = <47>;
-		clocks = <&ref24>;
-	};
diff --git a/Documentation/devicetree/bindings/serial/vt8500-uart.txt b/Documentation/devicetree/bindings/serial/vt8500-uart.txt
index 795c393..2b64e61 100644
--- a/Documentation/devicetree/bindings/serial/vt8500-uart.txt
+++ b/Documentation/devicetree/bindings/serial/vt8500-uart.txt
@@ -1,7 +1,8 @@
 * VIA VT8500 and WonderMedia WM8xxx UART Controller
 
 Required properties:
-- compatible: should be "via,vt8500-uart"
+- compatible: should be "via,vt8500-uart" (for VIA/WonderMedia chips up to and
+	including WM8850/WM8950), or "wm,wm8880-uart" (for WM8880 and later)
 
 - reg: base physical address of the controller and length of memory mapped
 	region.
diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt
index 1edd5fd..d9a452e 100644
--- a/Documentation/kernel-parameters.txt
+++ b/Documentation/kernel-parameters.txt
@@ -921,6 +921,12 @@
 
 	earlycon=	[KNL] Output early console device and options.
 
+		cdns,<addr>
+			Start an early, polled-mode console on a cadence serial
+			port at the specified address. The cadence serial port
+			must already be setup and configured. Options are not
+			yet supported.
+
 		uart[8250],io,<addr>[,options]
 		uart[8250],mmio,<addr>[,options]
 		uart[8250],mmio32,<addr>[,options]
@@ -936,6 +942,18 @@
 			must already be setup and configured. Options are not
 			yet supported.
 
+		msm_serial,<addr>
+			Start an early, polled-mode console on an msm serial
+			port at the specified address. The serial port
+			must already be setup and configured. Options are not
+			yet supported.
+
+		msm_serial_dm,<addr>
+			Start an early, polled-mode console on an msm serial
+			dm port at the specified address. The serial port
+			must already be setup and configured. Options are not
+			yet supported.
+
 		smh	Use ARM semihosting calls for early console.
 
 	earlyprintk=	[X86,SH,BLACKFIN,ARM,M68k]
diff --git a/Documentation/serial/driver b/Documentation/serial/driver
index 3bba1ae..ba64e4b 100644
--- a/Documentation/serial/driver
+++ b/Documentation/serial/driver
@@ -140,6 +140,8 @@
 	will append the character to the circular buffer and then call
 	start_tx() / stop_tx() to flush the data out.
 
+	Do not transmit if ch == '\0' (__DISABLED_CHAR).
+
 	Locking: none.
 	Interrupts: caller dependent.
 
diff --git a/arch/alpha/include/uapi/asm/ioctls.h b/arch/alpha/include/uapi/asm/ioctls.h
index 92c557b..f30c94a 100644
--- a/arch/alpha/include/uapi/asm/ioctls.h
+++ b/arch/alpha/include/uapi/asm/ioctls.h
@@ -90,6 +90,8 @@
 #define TIOCSBRK	0x5427  /* BSD compatibility */
 #define TIOCCBRK	0x5428  /* BSD compatibility */
 #define TIOCGSID	0x5429  /* Return the session ID of FD */
+#define TIOCGRS485	_IOR('T', 0x2E, struct serial_rs485)
+#define TIOCSRS485	_IOWR('T', 0x2F, struct serial_rs485)
 #define TIOCGPTN	_IOR('T',0x30, unsigned int) /* Get Pty Number (of pty-mux device) */
 #define TIOCSPTLCK	_IOW('T',0x31, int)  /* Lock/unlock Pty */
 #define TIOCGDEV	_IOR('T',0x32, unsigned int) /* Get primary device node of /dev/console */
diff --git a/arch/mips/include/uapi/asm/ioctls.h b/arch/mips/include/uapi/asm/ioctls.h
index b1e6377..740219c 100644
--- a/arch/mips/include/uapi/asm/ioctls.h
+++ b/arch/mips/include/uapi/asm/ioctls.h
@@ -81,6 +81,8 @@
 #define TCSETS2		_IOW('T', 0x2B, struct termios2)
 #define TCSETSW2	_IOW('T', 0x2C, struct termios2)
 #define TCSETSF2	_IOW('T', 0x2D, struct termios2)
+#define TIOCGRS485	_IOR('T', 0x2E, struct serial_rs485)
+#define TIOCSRS485	_IOWR('T', 0x2F, struct serial_rs485)
 #define TIOCGPTN	_IOR('T', 0x30, unsigned int) /* Get Pty Number (of pty-mux device) */
 #define TIOCSPTLCK	_IOW('T', 0x31, int)  /* Lock/unlock Pty */
 #define TIOCGDEV	_IOR('T', 0x32, unsigned int) /* Get primary device node of /dev/console */
diff --git a/arch/parisc/include/uapi/asm/ioctls.h b/arch/parisc/include/uapi/asm/ioctls.h
index 66719c3..b6572f0 100644
--- a/arch/parisc/include/uapi/asm/ioctls.h
+++ b/arch/parisc/include/uapi/asm/ioctls.h
@@ -50,6 +50,8 @@
 #define TCSETS2		_IOW('T',0x2B, struct termios2)
 #define TCSETSW2	_IOW('T',0x2C, struct termios2)
 #define TCSETSF2	_IOW('T',0x2D, struct termios2)
+#define TIOCGRS485	_IOR('T', 0x2E, struct serial_rs485)
+#define TIOCSRS485	_IOWR('T', 0x2F, struct serial_rs485)
 #define TIOCGPTN	_IOR('T',0x30, unsigned int) /* Get Pty Number (of pty-mux device) */
 #define TIOCSPTLCK	_IOW('T',0x31, int)  /* Lock/unlock Pty */
 #define TIOCGDEV	_IOR('T',0x32, int)  /* Get primary device node of /dev/console */
diff --git a/arch/sh/include/uapi/asm/ioctls.h b/arch/sh/include/uapi/asm/ioctls.h
index 3422410..c9903e5 100644
--- a/arch/sh/include/uapi/asm/ioctls.h
+++ b/arch/sh/include/uapi/asm/ioctls.h
@@ -83,6 +83,8 @@
 #define TCSETS2		_IOW('T', 43, struct termios2)
 #define TCSETSW2	_IOW('T', 44, struct termios2)
 #define TCSETSF2	_IOW('T', 45, struct termios2)
+#define TIOCGRS485	_IOR('T', 46, struct serial_rs485)
+#define TIOCSRS485	_IOWR('T', 47, struct serial_rs485)
 #define TIOCGPTN	_IOR('T',0x30, unsigned int) /* Get Pty Number (of pty-mux device) */
 #define TIOCSPTLCK	_IOW('T',0x31, int)  /* Lock/unlock Pty */
 #define TIOCGDEV	_IOR('T',0x32, unsigned int) /* Get primary device node of /dev/console */
diff --git a/arch/sparc/include/uapi/asm/ioctls.h b/arch/sparc/include/uapi/asm/ioctls.h
index 897d172..06b3f6c 100644
--- a/arch/sparc/include/uapi/asm/ioctls.h
+++ b/arch/sparc/include/uapi/asm/ioctls.h
@@ -24,6 +24,8 @@
 #define TIOCGPKT	_IOR('T', 0x38, int) /* Get packet mode state */
 #define TIOCGPTLCK	_IOR('T', 0x39, int) /* Get Pty lock state */
 #define TIOCGEXCL	_IOR('T', 0x40, int) /* Get exclusive mode state */
+#define TIOCGRS485	_IOR('T', 0x41, struct serial_rs485)
+#define TIOCSRS485	_IOWR('T', 0x42, struct serial_rs485)
 
 /* Note that all the ioctls that are not available in Linux have a 
  * double underscore on the front to: a) avoid some programs to
diff --git a/arch/xtensa/include/uapi/asm/ioctls.h b/arch/xtensa/include/uapi/asm/ioctls.h
index a47909f..518954e 100644
--- a/arch/xtensa/include/uapi/asm/ioctls.h
+++ b/arch/xtensa/include/uapi/asm/ioctls.h
@@ -95,6 +95,8 @@
 #define TCSETS2		_IOW('T', 43, struct termios2)
 #define TCSETSW2	_IOW('T', 44, struct termios2)
 #define TCSETSF2	_IOW('T', 45, struct termios2)
+#define TIOCGRS485	_IOR('T', 46, struct serial_rs485)
+#define TIOCSRS485	_IOWR('T', 47, struct serial_rs485)
 #define TIOCGPTN	_IOR('T',0x30, unsigned int) /* Get Pty Number (of pty-mux device) */
 #define TIOCSPTLCK	_IOW('T',0x31, int)  /* Lock/unlock Pty */
 #define TIOCGDEV	_IOR('T',0x32, unsigned int) /* Get primary device node of /dev/console */
diff --git a/drivers/isdn/i4l/isdn_tty.c b/drivers/isdn/i4l/isdn_tty.c
index 3c5f249..bc91261 100644
--- a/drivers/isdn/i4l/isdn_tty.c
+++ b/drivers/isdn/i4l/isdn_tty.c
@@ -1043,11 +1043,6 @@
 	if (!(cflag & PARODD))
 		cval |= UART_LCR_EPAR;
 
-	/* CTS flow control flag and modem status interrupts */
-	if (cflag & CRTSCTS) {
-		port->flags |= ASYNC_CTS_FLOW;
-	} else
-		port->flags &= ~ASYNC_CTS_FLOW;
 	if (cflag & CLOCAL)
 		port->flags &= ~ASYNC_CHECK_CD;
 	else {
diff --git a/drivers/staging/dgnc/dgnc_driver.c b/drivers/staging/dgnc/dgnc_driver.c
index 29cc2e4..2154665 100644
--- a/drivers/staging/dgnc/dgnc_driver.c
+++ b/drivers/staging/dgnc/dgnc_driver.c
@@ -112,19 +112,6 @@
 	{	DIGI_VID, PCI_DEVICE_CLASSIC_4_422_DID, PCI_ANY_ID, PCI_ANY_ID, 0, 0,	1 },
 	{	DIGI_VID, PCI_DEVICE_CLASSIC_8_DID, PCI_ANY_ID, PCI_ANY_ID, 0, 0,	2 },
 	{	DIGI_VID, PCI_DEVICE_CLASSIC_8_422_DID, PCI_ANY_ID, PCI_ANY_ID, 0, 0,	3 },
-	{	DIGI_VID, PCI_DEVICE_NEO_4_DID, PCI_ANY_ID, PCI_ANY_ID, 0, 0,		4 },
-	{	DIGI_VID, PCI_DEVICE_NEO_8_DID, PCI_ANY_ID, PCI_ANY_ID, 0, 0,		5 },
-	{	DIGI_VID, PCI_DEVICE_NEO_2DB9_DID, PCI_ANY_ID, PCI_ANY_ID, 0, 0,	6 },
-	{	DIGI_VID, PCI_DEVICE_NEO_2DB9PRI_DID, PCI_ANY_ID, PCI_ANY_ID, 0, 0,	7 },
-	{	DIGI_VID, PCI_DEVICE_NEO_2RJ45_DID, PCI_ANY_ID, PCI_ANY_ID, 0, 0,	8 },
-	{	DIGI_VID, PCI_DEVICE_NEO_2RJ45PRI_DID, PCI_ANY_ID, PCI_ANY_ID, 0, 0,	9 },
-	{	DIGI_VID, PCI_DEVICE_NEO_1_422_DID, PCI_ANY_ID, PCI_ANY_ID, 0, 0,	10 },
-	{	DIGI_VID, PCI_DEVICE_NEO_1_422_485_DID, PCI_ANY_ID, PCI_ANY_ID, 0, 0,	11 },
-	{	DIGI_VID, PCI_DEVICE_NEO_2_422_485_DID, PCI_ANY_ID, PCI_ANY_ID, 0, 0,	12 },
-	{	DIGI_VID, PCI_DEVICE_NEO_EXPRESS_8_DID, PCI_ANY_ID, PCI_ANY_ID, 0, 0,	 13 },
-	{	DIGI_VID, PCI_DEVICE_NEO_EXPRESS_4_DID, PCI_ANY_ID, PCI_ANY_ID, 0, 0,	14 },
-	{	DIGI_VID, PCI_DEVICE_NEO_EXPRESS_4RJ45_DID, PCI_ANY_ID, PCI_ANY_ID, 0, 0,	15 },
-	{	DIGI_VID, PCI_DEVICE_NEO_EXPRESS_8RJ45_DID, PCI_ANY_ID, PCI_ANY_ID, 0, 0,	16 },
 	{0,}						/* 0 terminated list. */
 };
 MODULE_DEVICE_TABLE(pci, dgnc_pci_tbl);
diff --git a/drivers/tty/hvc/hvc_xen.c b/drivers/tty/hvc/hvc_xen.c
index 2dc2831..2967f03 100644
--- a/drivers/tty/hvc/hvc_xen.c
+++ b/drivers/tty/hvc/hvc_xen.c
@@ -402,9 +402,6 @@
 			    evtchn);
 	if (ret)
 		goto error_xenbus;
-	ret = xenbus_printf(xbt, dev->nodename, "type", "ioemu");
-	if (ret)
-		goto error_xenbus;
 	ret = xenbus_transaction_end(xbt, 0);
 	if (ret) {
 		if (ret == -EAGAIN)
diff --git a/drivers/tty/metag_da.c b/drivers/tty/metag_da.c
index 7332e2c..3774600 100644
--- a/drivers/tty/metag_da.c
+++ b/drivers/tty/metag_da.c
@@ -17,6 +17,7 @@
 #include <linux/init.h>
 #include <linux/kernel.h>
 #include <linux/kthread.h>
+#include <linux/moduleparam.h>
 #include <linux/mutex.h>
 #include <linux/sched.h>
 #include <linux/serial.h>
@@ -70,6 +71,15 @@
 static struct timer_list put_timer;
 static struct task_struct *dashtty_thread;
 
+/*
+ * The console_poll parameter determines whether the console channel should be
+ * polled for input.
+ * By default the console channel isn't polled at all, in order to avoid the
+ * overhead, but that means it isn't possible to have a login on /dev/console.
+ */
+static bool console_poll;
+module_param(console_poll, bool, S_IRUGO);
+
 #define RX_BUF_SIZE 1024
 
 enum {
@@ -353,7 +363,7 @@
 	 * possible to have a login on /dev/console.
 	 *
 	 */
-	if (dport != &dashtty_ports[CONSOLE_CHANNEL])
+	if (console_poll || dport != &dashtty_ports[CONSOLE_CHANNEL])
 		if (atomic_inc_return(&num_channels_need_poll) == 1)
 			add_poll_timer(&poll_timer);
 
@@ -372,7 +382,7 @@
 	unsigned int count;
 
 	/* stop reading */
-	if (dport != &dashtty_ports[CONSOLE_CHANNEL])
+	if (console_poll || dport != &dashtty_ports[CONSOLE_CHANNEL])
 		if (atomic_dec_and_test(&num_channels_need_poll))
 			del_timer_sync(&poll_timer);
 
diff --git a/drivers/tty/moxa.c b/drivers/tty/moxa.c
index 1deaca4..14c54e0 100644
--- a/drivers/tty/moxa.c
+++ b/drivers/tty/moxa.c
@@ -1096,7 +1096,7 @@
 				continue;
 			}
 
-			printk(KERN_INFO "MOXA isa board found at 0x%.8lu and "
+			printk(KERN_INFO "MOXA isa board found at 0x%.8lx and "
 					"ready (%u ports, firmware loaded)\n",
 					baseaddr[i], brd->numPorts);
 
diff --git a/drivers/tty/n_tty.c b/drivers/tty/n_tty.c
index f44f1ba..89c4cee 100644
--- a/drivers/tty/n_tty.c
+++ b/drivers/tty/n_tty.c
@@ -1166,7 +1166,7 @@
 	}
 	put_tty_queue('\0', ldata);
 	if (waitqueue_active(&tty->read_wait))
-		wake_up_interruptible(&tty->read_wait);
+		wake_up_interruptible_poll(&tty->read_wait, POLLIN);
 }
 
 /**
@@ -1226,7 +1226,7 @@
 	} else
 		put_tty_queue(c, ldata);
 	if (waitqueue_active(&tty->read_wait))
-		wake_up_interruptible(&tty->read_wait);
+		wake_up_interruptible_poll(&tty->read_wait, POLLIN);
 }
 
 static void
@@ -1378,7 +1378,7 @@
 			ldata->canon_head = ldata->read_head;
 			kill_fasync(&tty->fasync, SIGIO, POLL_IN);
 			if (waitqueue_active(&tty->read_wait))
-				wake_up_interruptible(&tty->read_wait);
+				wake_up_interruptible_poll(&tty->read_wait, POLLIN);
 			return 0;
 		}
 	}
@@ -1679,7 +1679,7 @@
 		L_EXTPROC(tty)) {
 		kill_fasync(&tty->fasync, SIGIO, POLL_IN);
 		if (waitqueue_active(&tty->read_wait))
-			wake_up_interruptible(&tty->read_wait);
+			wake_up_interruptible_poll(&tty->read_wait, POLLIN);
 	}
 }
 
diff --git a/drivers/tty/nozomi.c b/drivers/tty/nozomi.c
index cd04293..74885af 100644
--- a/drivers/tty/nozomi.c
+++ b/drivers/tty/nozomi.c
@@ -523,7 +523,7 @@
 }
 
 /* Setup pointers to different channels and also setup buffer sizes. */
-static void setup_memory(struct nozomi *dc)
+static void nozomi_setup_memory(struct nozomi *dc)
 {
 	void __iomem *offset = dc->base_addr + dc->config_table.dl_start;
 	/* The length reported is including the length field of 4 bytes,
@@ -671,7 +671,7 @@
 		int i;
 		DBG1("Second phase, configuring card");
 
-		setup_memory(dc);
+		nozomi_setup_memory(dc);
 
 		dc->port[PORT_MDM].toggle_ul = dc->config_table.toggle.mdm_ul;
 		dc->port[PORT_MDM].toggle_dl = dc->config_table.toggle.mdm_dl;
@@ -705,7 +705,7 @@
 			 dc->config_table.version);
 
 		/* Here we should disable all I/O over F32. */
-		setup_memory(dc);
+		nozomi_setup_memory(dc);
 
 		/*
 		 * We should send ALL channel pair tokens back along
diff --git a/drivers/tty/pty.c b/drivers/tty/pty.c
index 9bbdb1d..7c4447a 100644
--- a/drivers/tty/pty.c
+++ b/drivers/tty/pty.c
@@ -24,6 +24,7 @@
 #include <linux/devpts_fs.h>
 #include <linux/slab.h>
 #include <linux/mutex.h>
+#include <linux/poll.h>
 
 
 #ifdef CONFIG_UNIX98_PTYS
@@ -313,6 +314,42 @@
 }
 
 /**
+ *	pty_start - start() handler
+ *	pty_stop  - stop() handler
+ *	@tty: tty being flow-controlled
+ *
+ *	Propagates the TIOCPKT status to the master pty.
+ *
+ *	NB: only the master pty can be in packet mode so only the slave
+ *	    needs start()/stop() handlers
+ */
+static void pty_start(struct tty_struct *tty)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&tty->ctrl_lock, flags);
+	if (tty->link && tty->link->packet) {
+		tty->ctrl_status &= ~TIOCPKT_STOP;
+		tty->ctrl_status |= TIOCPKT_START;
+		wake_up_interruptible_poll(&tty->link->read_wait, POLLIN);
+	}
+	spin_unlock_irqrestore(&tty->ctrl_lock, flags);
+}
+
+static void pty_stop(struct tty_struct *tty)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&tty->ctrl_lock, flags);
+	if (tty->link && tty->link->packet) {
+		tty->ctrl_status &= ~TIOCPKT_START;
+		tty->ctrl_status |= TIOCPKT_STOP;
+		wake_up_interruptible_poll(&tty->link->read_wait, POLLIN);
+	}
+	spin_unlock_irqrestore(&tty->ctrl_lock, flags);
+}
+
+/**
  *	pty_common_install		-	set up the pty pair
  *	@driver: the pty driver
  *	@tty: the tty being instantiated
@@ -471,6 +508,8 @@
 	.set_termios = pty_set_termios,
 	.cleanup = pty_cleanup,
 	.resize = pty_resize,
+	.start = pty_start,
+	.stop = pty_stop,
 	.remove = pty_remove
 };
 
@@ -646,6 +685,8 @@
 	.chars_in_buffer = pty_chars_in_buffer,
 	.unthrottle = pty_unthrottle,
 	.set_termios = pty_set_termios,
+	.start = pty_start,
+	.stop = pty_stop,
 	.shutdown = pty_unix98_shutdown,
 	.cleanup = pty_cleanup,
 };
diff --git a/drivers/tty/serial/8250/8250.h b/drivers/tty/serial/8250/8250.h
index 1b08c91..1bcb4b2 100644
--- a/drivers/tty/serial/8250/8250.h
+++ b/drivers/tty/serial/8250/8250.h
@@ -72,6 +72,7 @@
 #define UART_CAP_UUE	(1 << 12)	/* UART needs IER bit 6 set (Xscale) */
 #define UART_CAP_RTOIE	(1 << 13)	/* UART needs IER bit 4 set (Xscale, Tegra) */
 #define UART_CAP_HFIFO	(1 << 14)	/* UART has a "hidden" FIFO */
+#define UART_CAP_RPM	(1 << 15)	/* Runtime PM is active while idle */
 
 #define UART_BUG_QUOT	(1 << 0)	/* UART has buggy quot LSB */
 #define UART_BUG_TXEN	(1 << 1)	/* UART has buggy TX IIR status */
@@ -112,6 +113,8 @@
 	up->dl_write(up, value);
 }
 
+struct uart_8250_port *serial8250_get_port(int line);
+
 #if defined(__alpha__) && !defined(CONFIG_PCI)
 /*
  * Digital did something really horribly wrong with the OUT1 and OUT2
diff --git a/drivers/tty/serial/8250/8250_core.c b/drivers/tty/serial/8250/8250_core.c
index bd67294..ca5cfdc 100644
--- a/drivers/tty/serial/8250/8250_core.c
+++ b/drivers/tty/serial/8250/8250_core.c
@@ -37,6 +37,8 @@
 #include <linux/nmi.h>
 #include <linux/mutex.h>
 #include <linux/slab.h>
+#include <linux/uaccess.h>
+#include <linux/pm_runtime.h>
 #ifdef CONFIG_SPARC
 #include <linux/sunserialcore.h>
 #endif
@@ -539,6 +541,53 @@
 }
 EXPORT_SYMBOL_GPL(serial8250_clear_and_reinit_fifos);
 
+static void serial8250_rpm_get(struct uart_8250_port *p)
+{
+	if (!(p->capabilities & UART_CAP_RPM))
+		return;
+	pm_runtime_get_sync(p->port.dev);
+}
+
+static void serial8250_rpm_put(struct uart_8250_port *p)
+{
+	if (!(p->capabilities & UART_CAP_RPM))
+		return;
+	pm_runtime_mark_last_busy(p->port.dev);
+	pm_runtime_put_autosuspend(p->port.dev);
+}
+
+/*
+ * This two wrapper ensure, that enable_runtime_pm_tx() can be called more than
+ * once and disable_runtime_pm_tx() will still disable RPM because the fifo is
+ * empty and the HW can idle again.
+ */
+static void serial8250_rpm_get_tx(struct uart_8250_port *p)
+{
+	unsigned char rpm_active;
+
+	if (!(p->capabilities & UART_CAP_RPM))
+		return;
+
+	rpm_active = xchg(&p->rpm_tx_active, 1);
+	if (rpm_active)
+		return;
+	pm_runtime_get_sync(p->port.dev);
+}
+
+static void serial8250_rpm_put_tx(struct uart_8250_port *p)
+{
+	unsigned char rpm_active;
+
+	if (!(p->capabilities & UART_CAP_RPM))
+		return;
+
+	rpm_active = xchg(&p->rpm_tx_active, 0);
+	if (!rpm_active)
+		return;
+	pm_runtime_mark_last_busy(p->port.dev);
+	pm_runtime_put_autosuspend(p->port.dev);
+}
+
 /*
  * IER sleep support.  UARTs which have EFRs need the "extended
  * capability" bit enabled.  Note that on XR16C850s, we need to
@@ -553,10 +602,11 @@
 	 * offset but the UART channel may only write to the corresponding
 	 * bit.
 	 */
+	serial8250_rpm_get(p);
 	if ((p->port.type == PORT_XR17V35X) ||
 	   (p->port.type == PORT_XR17D15X)) {
 		serial_out(p, UART_EXAR_SLEEP, sleep ? 0xff : 0);
-		return;
+		goto out;
 	}
 
 	if (p->capabilities & UART_CAP_SLEEP) {
@@ -572,6 +622,8 @@
 			serial_out(p, UART_LCR, 0);
 		}
 	}
+out:
+	serial8250_rpm_put(p);
 }
 
 #ifdef CONFIG_SERIAL_8250_RSA
@@ -1272,6 +1324,7 @@
 	if (p->ier & UART_IER_THRI) {
 		p->ier &= ~UART_IER_THRI;
 		serial_out(p, UART_IER, p->ier);
+		serial8250_rpm_put_tx(p);
 	}
 }
 
@@ -1279,6 +1332,7 @@
 {
 	struct uart_8250_port *up = up_to_u8250p(port);
 
+	serial8250_rpm_get(up);
 	__stop_tx(up);
 
 	/*
@@ -1288,12 +1342,14 @@
 		up->acr |= UART_ACR_TXDIS;
 		serial_icr_write(up, UART_ACR, up->acr);
 	}
+	serial8250_rpm_put(up);
 }
 
 static void serial8250_start_tx(struct uart_port *port)
 {
 	struct uart_8250_port *up = up_to_u8250p(port);
 
+	serial8250_rpm_get_tx(up);
 	if (up->dma && !serial8250_tx_dma(up)) {
 		return;
 	} else if (!(up->ier & UART_IER_THRI)) {
@@ -1318,13 +1374,27 @@
 	}
 }
 
+static void serial8250_throttle(struct uart_port *port)
+{
+	port->throttle(port);
+}
+
+static void serial8250_unthrottle(struct uart_port *port)
+{
+	port->unthrottle(port);
+}
+
 static void serial8250_stop_rx(struct uart_port *port)
 {
 	struct uart_8250_port *up = up_to_u8250p(port);
 
-	up->ier &= ~UART_IER_RLSI;
+	serial8250_rpm_get(up);
+
+	up->ier &= ~(UART_IER_RLSI | UART_IER_RDI);
 	up->port.read_status_mask &= ~UART_LSR_DR;
 	serial_port_out(port, UART_IER, up->ier);
+
+	serial8250_rpm_put(up);
 }
 
 static void serial8250_enable_ms(struct uart_port *port)
@@ -1336,7 +1406,10 @@
 		return;
 
 	up->ier |= UART_IER_MSI;
+
+	serial8250_rpm_get(up);
 	serial_port_out(port, UART_IER, up->ier);
+	serial8250_rpm_put(up);
 }
 
 /*
@@ -1458,11 +1531,17 @@
 
 	DEBUG_INTR("THRE...");
 
-	if (uart_circ_empty(xmit))
+	/*
+	 * With RPM enabled, we have to wait once the FIFO is empty before the
+	 * HW can go idle. So we get here once again with empty FIFO and disable
+	 * the interrupt and RPM in __stop_tx()
+	 */
+	if (uart_circ_empty(xmit) && !(up->capabilities & UART_CAP_RPM))
 		__stop_tx(up);
 }
 EXPORT_SYMBOL_GPL(serial8250_tx_chars);
 
+/* Caller holds uart port lock */
 unsigned int serial8250_modem_status(struct uart_8250_port *up)
 {
 	struct uart_port *port = &up->port;
@@ -1525,9 +1604,17 @@
 
 static int serial8250_default_handle_irq(struct uart_port *port)
 {
-	unsigned int iir = serial_port_in(port, UART_IIR);
+	struct uart_8250_port *up = up_to_u8250p(port);
+	unsigned int iir;
+	int ret;
 
-	return serial8250_handle_irq(port, iir);
+	serial8250_rpm_get(up);
+
+	iir = serial_port_in(port, UART_IIR);
+	ret = serial8250_handle_irq(port, iir);
+
+	serial8250_rpm_put(up);
+	return ret;
 }
 
 /*
@@ -1784,11 +1871,15 @@
 	unsigned long flags;
 	unsigned int lsr;
 
+	serial8250_rpm_get(up);
+
 	spin_lock_irqsave(&port->lock, flags);
 	lsr = serial_port_in(port, UART_LSR);
 	up->lsr_saved_flags |= lsr & LSR_SAVE_FLAGS;
 	spin_unlock_irqrestore(&port->lock, flags);
 
+	serial8250_rpm_put(up);
+
 	return (lsr & BOTH_EMPTY) == BOTH_EMPTY ? TIOCSER_TEMT : 0;
 }
 
@@ -1798,7 +1889,9 @@
 	unsigned int status;
 	unsigned int ret;
 
+	serial8250_rpm_get(up);
 	status = serial8250_modem_status(up);
+	serial8250_rpm_put(up);
 
 	ret = 0;
 	if (status & UART_MSR_DCD)
@@ -1838,6 +1931,7 @@
 	struct uart_8250_port *up = up_to_u8250p(port);
 	unsigned long flags;
 
+	serial8250_rpm_get(up);
 	spin_lock_irqsave(&port->lock, flags);
 	if (break_state == -1)
 		up->lcr |= UART_LCR_SBC;
@@ -1845,6 +1939,7 @@
 		up->lcr &= ~UART_LCR_SBC;
 	serial_port_out(port, UART_LCR, up->lcr);
 	spin_unlock_irqrestore(&port->lock, flags);
+	serial8250_rpm_put(up);
 }
 
 /*
@@ -1889,12 +1984,23 @@
 
 static int serial8250_get_poll_char(struct uart_port *port)
 {
-	unsigned char lsr = serial_port_in(port, UART_LSR);
+	struct uart_8250_port *up = up_to_u8250p(port);
+	unsigned char lsr;
+	int status;
 
-	if (!(lsr & UART_LSR_DR))
-		return NO_POLL_CHAR;
+	serial8250_rpm_get(up);
 
-	return serial_port_in(port, UART_RX);
+	lsr = serial_port_in(port, UART_LSR);
+
+	if (!(lsr & UART_LSR_DR)) {
+		status = NO_POLL_CHAR;
+		goto out;
+	}
+
+	status = serial_port_in(port, UART_RX);
+out:
+	serial8250_rpm_put(up);
+	return status;
 }
 
 
@@ -1904,6 +2010,7 @@
 	unsigned int ier;
 	struct uart_8250_port *up = up_to_u8250p(port);
 
+	serial8250_rpm_get(up);
 	/*
 	 *	First save the IER then disable the interrupts
 	 */
@@ -1925,11 +2032,12 @@
 	 */
 	wait_for_xmitr(up, BOTH_EMPTY);
 	serial_port_out(port, UART_IER, ier);
+	serial8250_rpm_put(up);
 }
 
 #endif /* CONFIG_CONSOLE_POLL */
 
-static int serial8250_startup(struct uart_port *port)
+int serial8250_do_startup(struct uart_port *port)
 {
 	struct uart_8250_port *up = up_to_u8250p(port);
 	unsigned long flags;
@@ -1950,6 +2058,7 @@
 	if (port->iotype != up->cur_iotype)
 		set_io_from_upio(port);
 
+	serial8250_rpm_get(up);
 	if (port->type == PORT_16C950) {
 		/* Wake up and initialize UART */
 		up->acr = 0;
@@ -1970,7 +2079,6 @@
 	 */
 	enable_rsa(up);
 #endif
-
 	/*
 	 * Clear the FIFO buffers and disable them.
 	 * (they will be reenabled in set_termios())
@@ -1980,8 +2088,8 @@
 	/*
 	 * Clear the interrupt registers.
 	 */
-	serial_port_in(port, UART_LSR);
-	serial_port_in(port, UART_RX);
+	if (serial_port_in(port, UART_LSR) & UART_LSR_DR)
+		serial_port_in(port, UART_RX);
 	serial_port_in(port, UART_IIR);
 	serial_port_in(port, UART_MSR);
 
@@ -1994,7 +2102,8 @@
 	    (serial_port_in(port, UART_LSR) == 0xff)) {
 		printk_ratelimited(KERN_INFO "ttyS%d: LSR safety check engaged!\n",
 				   serial_index(port));
-		return -ENODEV;
+		retval = -ENODEV;
+		goto out;
 	}
 
 	/*
@@ -2079,7 +2188,7 @@
 	} else {
 		retval = serial_link_irq_chain(up);
 		if (retval)
-			return retval;
+			goto out;
 	}
 
 	/*
@@ -2141,8 +2250,8 @@
 	 * saved flags to avoid getting false values from polling
 	 * routines or the previous session.
 	 */
-	serial_port_in(port, UART_LSR);
-	serial_port_in(port, UART_RX);
+	if (serial_port_in(port, UART_LSR) & UART_LSR_DR)
+		serial_port_in(port, UART_RX);
 	serial_port_in(port, UART_IIR);
 	serial_port_in(port, UART_MSR);
 	up->lsr_saved_flags = 0;
@@ -2177,15 +2286,26 @@
 		outb_p(0x80, icp);
 		inb_p(icp);
 	}
+	retval = 0;
+out:
+	serial8250_rpm_put(up);
+	return retval;
+}
+EXPORT_SYMBOL_GPL(serial8250_do_startup);
 
-	return 0;
+static int serial8250_startup(struct uart_port *port)
+{
+	if (port->startup)
+		return port->startup(port);
+	return serial8250_do_startup(port);
 }
 
-static void serial8250_shutdown(struct uart_port *port)
+void serial8250_do_shutdown(struct uart_port *port)
 {
 	struct uart_8250_port *up = up_to_u8250p(port);
 	unsigned long flags;
 
+	serial8250_rpm_get(up);
 	/*
 	 * Disable interrupts from this port
 	 */
@@ -2224,13 +2344,24 @@
 	 * Read data port to reset things, and then unlink from
 	 * the IRQ chain.
 	 */
-	serial_port_in(port, UART_RX);
+	if (serial_port_in(port, UART_LSR) & UART_LSR_DR)
+		serial_port_in(port, UART_RX);
+	serial8250_rpm_put(up);
 
 	del_timer_sync(&up->timer);
 	up->timer.function = serial8250_timeout;
 	if (port->irq)
 		serial_unlink_irq_chain(up);
 }
+EXPORT_SYMBOL_GPL(serial8250_do_shutdown);
+
+static void serial8250_shutdown(struct uart_port *port)
+{
+	if (port->shutdown)
+		port->shutdown(port);
+	else
+		serial8250_do_shutdown(port);
+}
 
 static unsigned int serial8250_get_divisor(struct uart_port *port, unsigned int baud)
 {
@@ -2319,11 +2450,9 @@
 	 * the trigger, or the MCR RTS bit is cleared.  In the case where
 	 * the remote UART is not using CTS auto flow control, we must
 	 * have sufficient FIFO entries for the latency of the remote
-	 * UART to respond.  IOW, at least 32 bytes of FIFO. Also enable
-	 * AFE if hw flow control is supported
+	 * UART to respond.  IOW, at least 32 bytes of FIFO.
 	 */
-	if ((up->capabilities & UART_CAP_AFE && (port->fifosize >= 32)) ||
-	    (port->flags & UPF_HARD_FLOW)) {
+	if (up->capabilities & UART_CAP_AFE && port->fifosize >= 32) {
 		up->mcr &= ~UART_MCR_AFE;
 		if (termios->c_cflag & CRTSCTS)
 			up->mcr |= UART_MCR_AFE;
@@ -2333,6 +2462,7 @@
 	 * Ok, we're now changing the port state.  Do it with
 	 * interrupts disabled.
 	 */
+	serial8250_rpm_get(up);
 	spin_lock_irqsave(&port->lock, flags);
 
 	/*
@@ -2454,6 +2584,8 @@
 	}
 	serial8250_set_mctrl(port, port->mctrl);
 	spin_unlock_irqrestore(&port->lock, flags);
+	serial8250_rpm_put(up);
+
 	/* Don't rewrite B0 */
 	if (tty_termios_baud_rate(termios))
 		tty_termios_encode_baud_rate(termios, baud, baud);
@@ -2843,6 +2975,42 @@
 	return 0;
 }
 
+static int serial8250_ioctl(struct uart_port *port, unsigned int cmd,
+			   unsigned long arg)
+{
+	struct uart_8250_port *up =
+		container_of(port, struct uart_8250_port, port);
+	int ret;
+	struct serial_rs485 rs485_config;
+
+	if (!up->rs485_config)
+		return -ENOIOCTLCMD;
+
+	switch (cmd) {
+	case TIOCSRS485:
+		if (copy_from_user(&rs485_config, (void __user *)arg,
+				   sizeof(rs485_config)))
+			return -EFAULT;
+
+		ret = up->rs485_config(up, &rs485_config);
+		if (ret)
+			return ret;
+
+		memcpy(&up->rs485, &rs485_config, sizeof(rs485_config));
+
+		return 0;
+	case TIOCGRS485:
+		if (copy_to_user((void __user *)arg, &up->rs485,
+				 sizeof(up->rs485)))
+			return -EFAULT;
+		return 0;
+	default:
+		break;
+	}
+
+	return -ENOIOCTLCMD;
+}
+
 static const char *
 serial8250_type(struct uart_port *port)
 {
@@ -2859,6 +3027,8 @@
 	.get_mctrl	= serial8250_get_mctrl,
 	.stop_tx	= serial8250_stop_tx,
 	.start_tx	= serial8250_start_tx,
+	.throttle	= serial8250_throttle,
+	.unthrottle	= serial8250_unthrottle,
 	.stop_rx	= serial8250_stop_rx,
 	.enable_ms	= serial8250_enable_ms,
 	.break_ctl	= serial8250_break_ctl,
@@ -2872,6 +3042,7 @@
 	.request_port	= serial8250_request_port,
 	.config_port	= serial8250_config_port,
 	.verify_port	= serial8250_verify_port,
+	.ioctl		= serial8250_ioctl,
 #ifdef CONFIG_CONSOLE_POLL
 	.poll_get_char = serial8250_get_poll_char,
 	.poll_put_char = serial8250_put_poll_char,
@@ -2880,6 +3051,24 @@
 
 static struct uart_8250_port serial8250_ports[UART_NR];
 
+/**
+ * serial8250_get_port - retrieve struct uart_8250_port
+ * @line: serial line number
+ *
+ * This function retrieves struct uart_8250_port for the specific line.
+ * This struct *must* *not* be used to perform a 8250 or serial core operation
+ * which is not accessible otherwise. Its only purpose is to make the struct
+ * accessible to the runtime-pm callbacks for context suspend/restore.
+ * The lock assumption made here is none because runtime-pm suspend/resume
+ * callbacks should not be invoked if there is any operation performed on the
+ * port.
+ */
+struct uart_8250_port *serial8250_get_port(int line)
+{
+	return &serial8250_ports[line];
+}
+EXPORT_SYMBOL_GPL(serial8250_get_port);
+
 static void (*serial8250_isa_config)(int port, struct uart_port *up,
 	unsigned short *capabilities);
 
@@ -3007,6 +3196,8 @@
 
 	touch_nmi_watchdog();
 
+	serial8250_rpm_get(up);
+
 	if (port->sysrq || oops_in_progress)
 		locked = spin_trylock_irqsave(&port->lock, flags);
 	else
@@ -3043,6 +3234,7 @@
 
 	if (locked)
 		spin_unlock_irqrestore(&port->lock, flags);
+	serial8250_rpm_put(up);
 }
 
 static int __init serial8250_console_setup(struct console *co, char *options)
@@ -3324,6 +3516,11 @@
 		if (uart_match_port(&serial8250_ports[i].port, port))
 			return &serial8250_ports[i];
 
+	/* try line number first if still available */
+	i = port->line;
+	if (i < nr_uarts && serial8250_ports[i].port.type == PORT_UNKNOWN &&
+			serial8250_ports[i].port.iobase == 0)
+		return &serial8250_ports[i];
 	/*
 	 * We didn't find a matching entry, so look for the first
 	 * free entry.  We look for one which hasn't been previously
@@ -3388,6 +3585,10 @@
 		uart->port.fifosize	= up->port.fifosize;
 		uart->tx_loadsz		= up->tx_loadsz;
 		uart->capabilities	= up->capabilities;
+		uart->rs485_config	= up->rs485_config;
+		uart->rs485		= up->rs485;
+		uart->port.throttle	= up->port.throttle;
+		uart->port.unthrottle	= up->port.unthrottle;
 
 		/* Take tx_loadsz from fifosize if it wasn't set separately */
 		if (uart->port.fifosize && !uart->tx_loadsz)
@@ -3410,6 +3611,10 @@
 		/*  Possibly override set_termios call */
 		if (up->port.set_termios)
 			uart->port.set_termios = up->port.set_termios;
+		if (up->port.startup)
+			uart->port.startup = up->port.startup;
+		if (up->port.shutdown)
+			uart->port.shutdown = up->port.shutdown;
 		if (up->port.pm)
 			uart->port.pm = up->port.pm;
 		if (up->port.handle_break)
diff --git a/drivers/tty/serial/8250/8250_fintek.c b/drivers/tty/serial/8250/8250_fintek.c
new file mode 100644
index 0000000..1bb28cb
--- /dev/null
+++ b/drivers/tty/serial/8250/8250_fintek.c
@@ -0,0 +1,249 @@
+/*
+ *  Probe for F81216A LPC to 4 UART
+ *
+ *  Based on drivers/tty/serial/8250_pnp.c, by Russell King, et al
+ *
+ *  Copyright (C) 2014 Ricardo Ribalda, Qtechnology A/S
+ *
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License.
+ */
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/pnp.h>
+#include <linux/kernel.h>
+#include <linux/serial_core.h>
+#include  "8250.h"
+
+#define ADDR_PORT 0x4E
+#define DATA_PORT 0x4F
+#define ENTRY_KEY 0x77
+#define EXIT_KEY 0xAA
+#define CHIP_ID1  0x20
+#define CHIP_ID1_VAL 0x02
+#define CHIP_ID2  0x21
+#define CHIP_ID2_VAL 0x16
+#define VENDOR_ID1 0x23
+#define VENDOR_ID1_VAL 0x19
+#define VENDOR_ID2 0x24
+#define VENDOR_ID2_VAL 0x34
+#define LDN 0x7
+
+#define RS485  0xF0
+#define RTS_INVERT BIT(5)
+#define RS485_URA BIT(4)
+#define RXW4C_IRA BIT(3)
+#define TXW4C_IRA BIT(2)
+
+#define DRIVER_NAME "8250_fintek"
+
+static int fintek_8250_enter_key(void){
+
+	if (!request_muxed_region(ADDR_PORT, 2, DRIVER_NAME))
+		return -EBUSY;
+
+	outb(ENTRY_KEY, ADDR_PORT);
+	outb(ENTRY_KEY, ADDR_PORT);
+	return 0;
+}
+
+static void fintek_8250_exit_key(void){
+
+	outb(EXIT_KEY, ADDR_PORT);
+	release_region(ADDR_PORT, 2);
+}
+
+static int fintek_8250_get_index(resource_size_t base_addr)
+{
+	resource_size_t base[] = {0x3f8, 0x2f8, 0x3e8, 0x2e8};
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(base); i++)
+		if (base_addr == base[i])
+			return i;
+
+	return -ENODEV;
+}
+
+static int fintek_8250_check_id(void)
+{
+
+	outb(CHIP_ID1, ADDR_PORT);
+	if (inb(DATA_PORT) != CHIP_ID1_VAL)
+		return -ENODEV;
+
+	outb(CHIP_ID2, ADDR_PORT);
+	if (inb(DATA_PORT) != CHIP_ID2_VAL)
+		return -ENODEV;
+
+	outb(VENDOR_ID1, ADDR_PORT);
+	if (inb(DATA_PORT) != VENDOR_ID1_VAL)
+		return -ENODEV;
+
+	outb(VENDOR_ID2, ADDR_PORT);
+	if (inb(DATA_PORT) != VENDOR_ID2_VAL)
+		return -ENODEV;
+
+	return 0;
+}
+
+static int fintek_8250_rs4850_config(struct uart_8250_port *uart,
+			      struct serial_rs485 *rs485)
+{
+	uint8_t config = 0;
+	int index = fintek_8250_get_index(uart->port.iobase);
+
+	if (index < 0)
+		return -EINVAL;
+
+	if (rs485->flags & SER_RS485_ENABLED)
+		memset(rs485->padding, 0, sizeof(rs485->padding));
+	else
+		memset(rs485, 0, sizeof(*rs485));
+
+	rs485->flags &= SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND |
+			SER_RS485_RTS_AFTER_SEND;
+
+	if (rs485->delay_rts_before_send) {
+		rs485->delay_rts_before_send = 1;
+		config |= TXW4C_IRA;
+	}
+
+	if (rs485->delay_rts_after_send) {
+		rs485->delay_rts_after_send = 1;
+		config |= RXW4C_IRA;
+	}
+
+	if ((!!(rs485->flags & SER_RS485_RTS_ON_SEND)) ==
+			(!!(rs485->flags & SER_RS485_RTS_AFTER_SEND)))
+		rs485->flags &= SER_RS485_ENABLED;
+	else
+		config |= RS485_URA;
+
+	if (rs485->flags & SER_RS485_RTS_ON_SEND)
+		config |= RTS_INVERT;
+
+	if (fintek_8250_enter_key())
+		return -EBUSY;
+
+	outb(LDN, ADDR_PORT);
+	outb(index, DATA_PORT);
+	outb(RS485, ADDR_PORT);
+	outb(config, DATA_PORT);
+	fintek_8250_exit_key();
+
+	return 0;
+}
+
+static int
+fintek_8250_probe(struct pnp_dev *dev, const struct pnp_device_id *dev_id)
+{
+	int line;
+	struct uart_8250_port uart;
+	int ret;
+
+	if (!pnp_port_valid(dev, 0))
+		return -ENODEV;
+
+	if (fintek_8250_get_index(pnp_port_start(dev, 0)) < 0)
+		return -ENODEV;
+
+	/* Enable configuration registers*/
+	if (fintek_8250_enter_key())
+		return -EBUSY;
+
+	/*Check ID*/
+	ret = fintek_8250_check_id();
+	fintek_8250_exit_key();
+	if (ret)
+		return ret;
+
+	memset(&uart, 0, sizeof(uart));
+	if (!pnp_irq_valid(dev, 0))
+		return -ENODEV;
+	uart.port.irq = pnp_irq(dev, 0);
+	uart.port.iobase = pnp_port_start(dev, 0);
+	uart.port.iotype = UPIO_PORT;
+	uart.rs485_config = fintek_8250_rs4850_config;
+
+	uart.port.flags |= UPF_SKIP_TEST | UPF_BOOT_AUTOCONF;
+	if (pnp_irq_flags(dev, 0) & IORESOURCE_IRQ_SHAREABLE)
+		uart.port.flags |= UPF_SHARE_IRQ;
+	uart.port.uartclk = 1843200;
+	uart.port.dev = &dev->dev;
+
+	line = serial8250_register_8250_port(&uart);
+	if (line < 0)
+		return -ENODEV;
+
+	pnp_set_drvdata(dev, (void *)((long)line + 1));
+	return 0;
+}
+
+static void fintek_8250_remove(struct pnp_dev *dev)
+{
+	long line = (long)pnp_get_drvdata(dev);
+
+	if (line)
+		serial8250_unregister_port(line - 1);
+}
+
+#ifdef CONFIG_PM
+static int fintek_8250_suspend(struct pnp_dev *dev, pm_message_t state)
+{
+	long line = (long)pnp_get_drvdata(dev);
+
+	if (!line)
+		return -ENODEV;
+	serial8250_suspend_port(line - 1);
+	return 0;
+}
+
+static int fintek_8250_resume(struct pnp_dev *dev)
+{
+	long line = (long)pnp_get_drvdata(dev);
+
+	if (!line)
+		return -ENODEV;
+	serial8250_resume_port(line - 1);
+	return 0;
+}
+#else
+#define fintek_8250_suspend NULL
+#define fintek_8250_resume NULL
+#endif /* CONFIG_PM */
+
+static const struct pnp_device_id fintek_dev_table[] = {
+	/* Qtechnology Panel PC / IO1000 */
+	{ "PNP0501"},
+	{}
+};
+
+MODULE_DEVICE_TABLE(pnp, fintek_dev_table);
+
+static struct pnp_driver fintek_8250_driver = {
+	.name		= DRIVER_NAME,
+	.probe		= fintek_8250_probe,
+	.remove		= fintek_8250_remove,
+	.suspend	= fintek_8250_suspend,
+	.resume		= fintek_8250_resume,
+	.id_table	= fintek_dev_table,
+};
+
+static int fintek_8250_init(void)
+{
+	return pnp_register_driver(&fintek_8250_driver);
+}
+module_init(fintek_8250_init);
+
+static void fintek_8250_exit(void)
+{
+	pnp_unregister_driver(&fintek_8250_driver);
+}
+module_exit(fintek_8250_exit);
+
+MODULE_DESCRIPTION("Fintek F812164 module");
+MODULE_AUTHOR("Ricardo Ribalda <ricardo.ribalda@gmail.com>");
+MODULE_LICENSE("GPL");
diff --git a/drivers/tty/serial/8250/8250_hp300.c b/drivers/tty/serial/8250/8250_hp300.c
index 5bdaf27..afffe4d 100644
--- a/drivers/tty/serial/8250/8250_hp300.c
+++ b/drivers/tty/serial/8250/8250_hp300.c
@@ -21,7 +21,7 @@
 #include "8250.h"
 
 #if !defined(CONFIG_HPDCA) && !defined(CONFIG_HPAPCI)
-#warning CONFIG_8250 defined but neither CONFIG_HPDCA nor CONFIG_HPAPCI defined, are you sure?
+#warning CONFIG_SERIAL_8250 defined but neither CONFIG_HPDCA nor CONFIG_HPAPCI defined, are you sure?
 #endif
 
 #ifdef CONFIG_HPAPCI
diff --git a/drivers/tty/serial/8250/8250_mtk.c b/drivers/tty/serial/8250/8250_mtk.c
new file mode 100644
index 0000000..8f37d57
--- /dev/null
+++ b/drivers/tty/serial/8250/8250_mtk.c
@@ -0,0 +1,294 @@
+/*
+ * Mediatek 8250 driver.
+ *
+ * Copyright (c) 2014 MundoReader S.L.
+ * Author: Matthias Brugger <matthias.bgg@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of_irq.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+#include <linux/serial_8250.h>
+#include <linux/serial_reg.h>
+
+#include "8250.h"
+
+#define UART_MTK_HIGHS		0x09	/* Highspeed register */
+#define UART_MTK_SAMPLE_COUNT	0x0a	/* Sample count register */
+#define UART_MTK_SAMPLE_POINT	0x0b	/* Sample point register */
+#define MTK_UART_RATE_FIX	0x0d	/* UART Rate Fix Register */
+
+struct mtk8250_data {
+	int			line;
+	struct clk		*uart_clk;
+};
+
+static void
+mtk8250_set_termios(struct uart_port *port, struct ktermios *termios,
+			struct ktermios *old)
+{
+	unsigned long flags;
+	unsigned int baud, quot;
+
+	struct uart_8250_port *up =
+		container_of(port, struct uart_8250_port, port);
+
+	serial8250_do_set_termios(port, termios, old);
+
+	/*
+	 * Mediatek UARTs use an extra highspeed register (UART_MTK_HIGHS)
+	 *
+	 * We need to recalcualte the quot register, as the claculation depends
+	 * on the vaule in the highspeed register.
+	 *
+	 * Some baudrates are not supported by the chip, so we use the next
+	 * lower rate supported and update termios c_flag.
+	 *
+	 * If highspeed register is set to 3, we need to specify sample count
+	 * and sample point to increase accuracy. If not, we reset the
+	 * registers to their default values.
+	 */
+	baud = uart_get_baud_rate(port, termios, old,
+				  port->uartclk / 16 / 0xffff,
+				  port->uartclk / 16);
+
+	if (baud <= 115200) {
+		serial_port_out(port, UART_MTK_HIGHS, 0x0);
+		quot = uart_get_divisor(port, baud);
+	} else if (baud <= 576000) {
+		serial_port_out(port, UART_MTK_HIGHS, 0x2);
+
+		/* Set to next lower baudrate supported */
+		if ((baud == 500000) || (baud == 576000))
+			baud = 460800;
+		quot = DIV_ROUND_CLOSEST(port->uartclk, 4 * baud);
+	} else {
+		serial_port_out(port, UART_MTK_HIGHS, 0x3);
+
+		/* Set to highest baudrate supported */
+		if (baud >= 1152000)
+			baud = 921600;
+		quot = DIV_ROUND_CLOSEST(port->uartclk, 256 * baud);
+	}
+
+	/*
+	 * Ok, we're now changing the port state.  Do it with
+	 * interrupts disabled.
+	 */
+	spin_lock_irqsave(&port->lock, flags);
+
+	/* set DLAB we have cval saved in up->lcr from the call to the core */
+	serial_port_out(port, UART_LCR, up->lcr | UART_LCR_DLAB);
+	serial_dl_write(up, quot);
+
+	/* reset DLAB */
+	serial_port_out(port, UART_LCR, up->lcr);
+
+	if (baud > 460800) {
+		unsigned int tmp;
+
+		tmp = DIV_ROUND_CLOSEST(port->uartclk, quot * baud);
+		serial_port_out(port, UART_MTK_SAMPLE_COUNT, tmp - 1);
+		serial_port_out(port, UART_MTK_SAMPLE_POINT,
+					(tmp - 2) >> 1);
+	} else {
+		serial_port_out(port, UART_MTK_SAMPLE_COUNT, 0x00);
+		serial_port_out(port, UART_MTK_SAMPLE_POINT, 0xff);
+	}
+
+	spin_unlock_irqrestore(&port->lock, flags);
+	/* Don't rewrite B0 */
+	if (tty_termios_baud_rate(termios))
+		tty_termios_encode_baud_rate(termios, baud, baud);
+}
+
+static void
+mtk8250_do_pm(struct uart_port *port, unsigned int state, unsigned int old)
+{
+	if (!state)
+		pm_runtime_get_sync(port->dev);
+
+	serial8250_do_pm(port, state, old);
+
+	if (state)
+		pm_runtime_put_sync_suspend(port->dev);
+}
+
+static int mtk8250_probe_of(struct platform_device *pdev, struct uart_port *p,
+			   struct mtk8250_data *data)
+{
+	int err;
+	struct device_node *np = pdev->dev.of_node;
+
+	data->uart_clk = of_clk_get(np, 0);
+	if (IS_ERR(data->uart_clk)) {
+		dev_warn(&pdev->dev, "Can't get timer clock\n");
+		return PTR_ERR(data->uart_clk);
+	}
+
+	err = clk_prepare_enable(data->uart_clk);
+	if (err) {
+		dev_warn(&pdev->dev, "Can't prepare clock\n");
+		clk_put(data->uart_clk);
+		return err;
+	}
+	p->uartclk = clk_get_rate(data->uart_clk);
+
+	return 0;
+}
+
+static int mtk8250_probe(struct platform_device *pdev)
+{
+	struct uart_8250_port uart = {};
+	struct resource *regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	struct resource *irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
+	struct mtk8250_data *data;
+	int err;
+
+	if (!regs || !irq) {
+		dev_err(&pdev->dev, "no registers/irq defined\n");
+		return -EINVAL;
+	}
+
+	uart.port.membase = devm_ioremap(&pdev->dev, regs->start,
+					 resource_size(regs));
+	if (!uart.port.membase)
+		return -ENOMEM;
+
+	data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	if (pdev->dev.of_node) {
+		err = mtk8250_probe_of(pdev, &uart.port, data);
+		if (err)
+			return err;
+	} else
+		return -ENODEV;
+
+	spin_lock_init(&uart.port.lock);
+	uart.port.mapbase = regs->start;
+	uart.port.irq = irq->start;
+	uart.port.pm = mtk8250_do_pm;
+	uart.port.type = PORT_16550;
+	uart.port.flags = UPF_BOOT_AUTOCONF | UPF_FIXED_PORT;
+	uart.port.dev = &pdev->dev;
+	uart.port.iotype = UPIO_MEM32;
+	uart.port.regshift = 2;
+	uart.port.private_data = data;
+	uart.port.set_termios = mtk8250_set_termios;
+
+	/* Disable Rate Fix function */
+	writel(0x0, uart.port.membase +
+			(MTK_UART_RATE_FIX << uart.port.regshift));
+
+	data->line = serial8250_register_8250_port(&uart);
+	if (data->line < 0)
+		return data->line;
+
+	platform_set_drvdata(pdev, data);
+
+	pm_runtime_set_active(&pdev->dev);
+	pm_runtime_enable(&pdev->dev);
+
+	return 0;
+}
+
+static int mtk8250_remove(struct platform_device *pdev)
+{
+	struct mtk8250_data *data = platform_get_drvdata(pdev);
+
+	pm_runtime_get_sync(&pdev->dev);
+
+	serial8250_unregister_port(data->line);
+	if (!IS_ERR(data->uart_clk)) {
+		clk_disable_unprepare(data->uart_clk);
+		clk_put(data->uart_clk);
+	}
+
+	pm_runtime_disable(&pdev->dev);
+	pm_runtime_put_noidle(&pdev->dev);
+	return 0;
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int mtk8250_suspend(struct device *dev)
+{
+	struct mtk8250_data *data = dev_get_drvdata(dev);
+
+	serial8250_suspend_port(data->line);
+
+	return 0;
+}
+
+static int mtk8250_resume(struct device *dev)
+{
+	struct mtk8250_data *data = dev_get_drvdata(dev);
+
+	serial8250_resume_port(data->line);
+
+	return 0;
+}
+#endif /* CONFIG_PM_SLEEP */
+
+#ifdef CONFIG_PM_RUNTIME
+static int mtk8250_runtime_suspend(struct device *dev)
+{
+	struct mtk8250_data *data = dev_get_drvdata(dev);
+
+	if (!IS_ERR(data->uart_clk))
+		clk_disable_unprepare(data->uart_clk);
+
+	return 0;
+}
+
+static int mtk8250_runtime_resume(struct device *dev)
+{
+	struct mtk8250_data *data = dev_get_drvdata(dev);
+
+	if (!IS_ERR(data->uart_clk))
+		clk_prepare_enable(data->uart_clk);
+
+	return 0;
+}
+#endif
+
+static const struct dev_pm_ops mtk8250_pm_ops = {
+	SET_SYSTEM_SLEEP_PM_OPS(mtk8250_suspend, mtk8250_resume)
+	SET_RUNTIME_PM_OPS(mtk8250_runtime_suspend, mtk8250_runtime_resume,
+				NULL)
+};
+
+static const struct of_device_id mtk8250_of_match[] = {
+	{ .compatible = "mediatek,mt6577-uart" },
+	{ /* Sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, mtk8250_of_match);
+
+static struct platform_driver mtk8250_platform_driver = {
+	.driver = {
+		.name		= "mt6577-uart",
+		.pm		= &mtk8250_pm_ops,
+		.of_match_table	= mtk8250_of_match,
+	},
+	.probe			= mtk8250_probe,
+	.remove			= mtk8250_remove,
+};
+module_platform_driver(mtk8250_platform_driver);
+
+MODULE_AUTHOR("Matthias Brugger");
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION("Mediatek 8250 serial port driver");
diff --git a/drivers/tty/serial/8250/8250_pci.c b/drivers/tty/serial/8250/8250_pci.c
index 61830b1..4f1cd29 100644
--- a/drivers/tty/serial/8250/8250_pci.c
+++ b/drivers/tty/serial/8250/8250_pci.c
@@ -1355,9 +1355,6 @@
 #define BYT_PRV_CLK_N_VAL_SHIFT		16
 #define BYT_PRV_CLK_UPDATE		(1 << 31)
 
-#define BYT_GENERAL_REG			0x808
-#define BYT_GENERAL_DIS_RTS_N_OVERRIDE	(1 << 3)
-
 #define BYT_TX_OVF_INT			0x820
 #define BYT_TX_OVF_INT_MASK		(1 << 1)
 
@@ -1412,16 +1409,6 @@
 	reg |= BYT_PRV_CLK_EN | BYT_PRV_CLK_UPDATE;
 	writel(reg, p->membase + BYT_PRV_CLK);
 
-	/*
-	 * If auto-handshake mechanism is not enabled,
-	 * disable rts_n override
-	 */
-	reg = readl(p->membase + BYT_GENERAL_REG);
-	reg &= ~BYT_GENERAL_DIS_RTS_N_OVERRIDE;
-	if (termios->c_cflag & CRTSCTS)
-		reg |= BYT_GENERAL_DIS_RTS_N_OVERRIDE;
-	writel(reg, p->membase + BYT_GENERAL_REG);
-
 	serial8250_do_set_termios(p, termios, old);
 }
 
@@ -1788,6 +1775,7 @@
 #define PCI_DEVICE_ID_COMMTECH_4222PCIE	0x0022
 #define PCI_DEVICE_ID_BROADCOM_TRUMANAGE 0x160a
 #define PCI_DEVICE_ID_AMCC_ADDIDATA_APCI7800 0x818e
+#define PCI_DEVICE_ID_INTEL_QRK_UART	0x0936
 
 #define PCI_VENDOR_ID_SUNIX		0x1fd4
 #define PCI_DEVICE_ID_SUNIX_1999	0x1999
@@ -1898,6 +1886,13 @@
 		.subdevice	= PCI_ANY_ID,
 		.setup		= byt_serial_setup,
 	},
+	{
+		.vendor		= PCI_VENDOR_ID_INTEL,
+		.device		= PCI_DEVICE_ID_INTEL_QRK_UART,
+		.subvendor	= PCI_ANY_ID,
+		.subdevice	= PCI_ANY_ID,
+		.setup		= pci_default_setup,
+	},
 	/*
 	 * ITE
 	 */
@@ -2740,6 +2735,7 @@
 	pbn_ADDIDATA_PCIe_8_3906250,
 	pbn_ce4100_1_115200,
 	pbn_byt,
+	pbn_qrk,
 	pbn_omegapci,
 	pbn_NETMOS9900_2s_115200,
 	pbn_brcm_trumanage,
@@ -3490,6 +3486,12 @@
 		.uart_offset	= 0x80,
 		.reg_shift      = 2,
 	},
+	[pbn_qrk] = {
+		.flags		= FL_BASE0,
+		.num_ports	= 1,
+		.base_baud	= 2764800,
+		.reg_shift	= 2,
+	},
 	[pbn_omegapci] = {
 		.flags		= FL_BASE0,
 		.num_ports	= 8,
@@ -5192,6 +5194,12 @@
 		pbn_byt },
 
 	/*
+	 * Intel Quark x1000
+	 */
+	{	PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_QRK_UART,
+		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+		pbn_qrk },
+	/*
 	 * Cronyx Omega PCI
 	 */
 	{	PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_CRONYX_OMEGA,
diff --git a/drivers/tty/serial/8250/Kconfig b/drivers/tty/serial/8250/Kconfig
index 349ee59..21eca79 100644
--- a/drivers/tty/serial/8250/Kconfig
+++ b/drivers/tty/serial/8250/Kconfig
@@ -298,3 +298,18 @@
 	  If you have a Ralink RT288x/RT305x SoC based board and want to use the
 	  serial port, say Y to this option. The driver can handle up to 2 serial
 	  ports. If unsure, say N.
+
+config SERIAL_8250_FINTEK
+	tristate "Support for Fintek F81216A LPC to 4 UART"
+	depends on SERIAL_8250 && PNP
+	help
+	  Selecting this option will add support for the Fintek F81216A
+	  LPC to 4 UART. This device has some RS485 functionality not available
+	  through the PNP driver. If unsure, say N.
+
+config SERIAL_8250_MT6577
+	bool "Mediatek serial port support"
+	depends on SERIAL_8250 && ARCH_MEDIATEK
+	help
+	  If you have a Mediatek based board and want to use the
+	  serial port, say Y to this option. If unsure, say N.
diff --git a/drivers/tty/serial/8250/Makefile b/drivers/tty/serial/8250/Makefile
index 36d68d0..5256b89 100644
--- a/drivers/tty/serial/8250/Makefile
+++ b/drivers/tty/serial/8250/Makefile
@@ -20,3 +20,5 @@
 obj-$(CONFIG_SERIAL_8250_FSL)		+= 8250_fsl.o
 obj-$(CONFIG_SERIAL_8250_DW)		+= 8250_dw.o
 obj-$(CONFIG_SERIAL_8250_EM)		+= 8250_em.o
+obj-$(CONFIG_SERIAL_8250_FINTEK)	+= 8250_fintek.o
+obj-$(CONFIG_SERIAL_8250_MT6577)	+= 8250_mtk.o
diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig
index 26cec64..649b784 100644
--- a/drivers/tty/serial/Kconfig
+++ b/drivers/tty/serial/Kconfig
@@ -200,10 +200,29 @@
 	  receives all kernel messages and warnings and which allows
 	  logins in single user mode).
 
+config SERIAL_MESON
+	tristate "Meson serial port support"
+	depends on ARCH_MESON
+	select SERIAL_CORE
+	help
+	  This enables the driver for the on-chip UARTs of the Amlogic
+	  MesonX processors.
+
+config SERIAL_MESON_CONSOLE
+	bool "Support for console on meson"
+	depends on SERIAL_MESON=y
+	select SERIAL_CORE_CONSOLE
+	help
+	  Say Y here if you wish to use a Amlogic MesonX UART as the
+	  system console (the system console is the device which
+	  receives all kernel messages and warnings and which allows
+	  logins in single user mode) as /dev/ttyAMLx.
+
 config SERIAL_CLPS711X
 	tristate "CLPS711X serial port support"
 	depends on ARCH_CLPS711X || COMPILE_TEST
 	select SERIAL_CORE
+	select SERIAL_MCTRL_GPIO if GPIOLIB
 	help
 	  This enables the driver for the on-chip UARTs of the Cirrus
 	  Logic EP711x/EP721x/EP731x processors.
@@ -220,7 +239,7 @@
 
 config SERIAL_SAMSUNG
 	tristate "Samsung SoC serial support"
-	depends on PLAT_SAMSUNG
+	depends on PLAT_SAMSUNG || ARCH_EXYNOS
 	select SERIAL_CORE
 	help
 	  Support for the on-chip UARTs on the Samsung S3C24XX series CPUs,
@@ -1051,6 +1070,7 @@
 	bool "MSM serial console support"
 	depends on SERIAL_MSM=y
 	select SERIAL_CORE_CONSOLE
+	select SERIAL_EARLYCON
 
 config SERIAL_MSM_HS
 	tristate "MSM UART High Speed: Serial Driver"
@@ -1410,6 +1430,7 @@
 	bool "Cadence UART console support"
 	depends on SERIAL_XILINX_PS_UART=y
 	select SERIAL_CORE_CONSOLE
+	select SERIAL_EARLYCON
 	help
 	  Enable a Cadence UART port to be the system console.
 
diff --git a/drivers/tty/serial/Makefile b/drivers/tty/serial/Makefile
index 0080cc3..9a548ac 100644
--- a/drivers/tty/serial/Makefile
+++ b/drivers/tty/serial/Makefile
@@ -48,6 +48,7 @@
 obj-$(CONFIG_SERIAL_ICOM) += icom.o
 obj-$(CONFIG_SERIAL_M32R_SIO) += m32r_sio.o
 obj-$(CONFIG_SERIAL_MPSC) += mpsc.o
+obj-$(CONFIG_SERIAL_MESON) += meson_uart.o
 obj-$(CONFIG_SERIAL_SB1250_DUART) += sb1250-duart.o
 obj-$(CONFIG_ETRAX_SERIAL) += crisv10.o
 obj-$(CONFIG_SERIAL_SCCNXP) += sccnxp.o
diff --git a/drivers/tty/serial/altera_jtaguart.c b/drivers/tty/serial/altera_jtaguart.c
index d22e3d9..932e019 100644
--- a/drivers/tty/serial/altera_jtaguart.c
+++ b/drivers/tty/serial/altera_jtaguart.c
@@ -462,7 +462,7 @@
 }
 
 #ifdef CONFIG_OF
-static struct of_device_id altera_jtaguart_match[] = {
+static const struct of_device_id altera_jtaguart_match[] = {
 	{ .compatible = "ALTR,juart-1.0", },
 	{ .compatible = "altr,juart-1.0", },
 	{},
diff --git a/drivers/tty/serial/altera_uart.c b/drivers/tty/serial/altera_uart.c
index 6a24323..1cb2cdb 100644
--- a/drivers/tty/serial/altera_uart.c
+++ b/drivers/tty/serial/altera_uart.c
@@ -610,7 +610,7 @@
 }
 
 #ifdef CONFIG_OF
-static struct of_device_id altera_uart_match[] = {
+static const struct of_device_id altera_uart_match[] = {
 	{ .compatible = "ALTR,uart-1.0", },
 	{ .compatible = "altr,uart-1.0", },
 	{},
diff --git a/drivers/tty/serial/amba-pl011.c b/drivers/tty/serial/amba-pl011.c
index 8572f2a..02016fc 100644
--- a/drivers/tty/serial/amba-pl011.c
+++ b/drivers/tty/serial/amba-pl011.c
@@ -678,7 +678,8 @@
 __releases(&uap->port.lock)
 __acquires(&uap->port.lock)
 {
-	struct uart_amba_port *uap = (struct uart_amba_port *)port;
+	struct uart_amba_port *uap =
+	    container_of(port, struct uart_amba_port, port);
 
 	if (!uap->using_tx_dma)
 		return;
@@ -1163,7 +1164,8 @@
 
 static void pl011_stop_tx(struct uart_port *port)
 {
-	struct uart_amba_port *uap = (struct uart_amba_port *)port;
+	struct uart_amba_port *uap =
+	    container_of(port, struct uart_amba_port, port);
 
 	uap->im &= ~UART011_TXIM;
 	writew(uap->im, uap->port.membase + UART011_IMSC);
@@ -1172,7 +1174,8 @@
 
 static void pl011_start_tx(struct uart_port *port)
 {
-	struct uart_amba_port *uap = (struct uart_amba_port *)port;
+	struct uart_amba_port *uap =
+	    container_of(port, struct uart_amba_port, port);
 
 	if (!pl011_dma_tx_start(uap)) {
 		uap->im |= UART011_TXIM;
@@ -1182,7 +1185,8 @@
 
 static void pl011_stop_rx(struct uart_port *port)
 {
-	struct uart_amba_port *uap = (struct uart_amba_port *)port;
+	struct uart_amba_port *uap =
+	    container_of(port, struct uart_amba_port, port);
 
 	uap->im &= ~(UART011_RXIM|UART011_RTIM|UART011_FEIM|
 		     UART011_PEIM|UART011_BEIM|UART011_OEIM);
@@ -1193,7 +1197,8 @@
 
 static void pl011_enable_ms(struct uart_port *port)
 {
-	struct uart_amba_port *uap = (struct uart_amba_port *)port;
+	struct uart_amba_port *uap =
+	    container_of(port, struct uart_amba_port, port);
 
 	uap->im |= UART011_RIMIM|UART011_CTSMIM|UART011_DCDMIM|UART011_DSRMIM;
 	writew(uap->im, uap->port.membase + UART011_IMSC);
@@ -1349,14 +1354,16 @@
 
 static unsigned int pl011_tx_empty(struct uart_port *port)
 {
-	struct uart_amba_port *uap = (struct uart_amba_port *)port;
+	struct uart_amba_port *uap =
+	    container_of(port, struct uart_amba_port, port);
 	unsigned int status = readw(uap->port.membase + UART01x_FR);
 	return status & (UART01x_FR_BUSY|UART01x_FR_TXFF) ? 0 : TIOCSER_TEMT;
 }
 
 static unsigned int pl011_get_mctrl(struct uart_port *port)
 {
-	struct uart_amba_port *uap = (struct uart_amba_port *)port;
+	struct uart_amba_port *uap =
+	    container_of(port, struct uart_amba_port, port);
 	unsigned int result = 0;
 	unsigned int status = readw(uap->port.membase + UART01x_FR);
 
@@ -1374,7 +1381,8 @@
 
 static void pl011_set_mctrl(struct uart_port *port, unsigned int mctrl)
 {
-	struct uart_amba_port *uap = (struct uart_amba_port *)port;
+	struct uart_amba_port *uap =
+	    container_of(port, struct uart_amba_port, port);
 	unsigned int cr;
 
 	cr = readw(uap->port.membase + UART011_CR);
@@ -1402,7 +1410,8 @@
 
 static void pl011_break_ctl(struct uart_port *port, int break_state)
 {
-	struct uart_amba_port *uap = (struct uart_amba_port *)port;
+	struct uart_amba_port *uap =
+	    container_of(port, struct uart_amba_port, port);
 	unsigned long flags;
 	unsigned int lcr_h;
 
@@ -1420,7 +1429,8 @@
 
 static void pl011_quiesce_irqs(struct uart_port *port)
 {
-	struct uart_amba_port *uap = (struct uart_amba_port *)port;
+	struct uart_amba_port *uap =
+	    container_of(port, struct uart_amba_port, port);
 	unsigned char __iomem *regs = uap->port.membase;
 
 	writew(readw(regs + UART011_MIS), regs + UART011_ICR);
@@ -1442,7 +1452,8 @@
 
 static int pl011_get_poll_char(struct uart_port *port)
 {
-	struct uart_amba_port *uap = (struct uart_amba_port *)port;
+	struct uart_amba_port *uap =
+	    container_of(port, struct uart_amba_port, port);
 	unsigned int status;
 
 	/*
@@ -1461,7 +1472,8 @@
 static void pl011_put_poll_char(struct uart_port *port,
 			 unsigned char ch)
 {
-	struct uart_amba_port *uap = (struct uart_amba_port *)port;
+	struct uart_amba_port *uap =
+	    container_of(port, struct uart_amba_port, port);
 
 	while (readw(uap->port.membase + UART01x_FR) & UART01x_FR_TXFF)
 		barrier();
@@ -1473,7 +1485,8 @@
 
 static int pl011_hwinit(struct uart_port *port)
 {
-	struct uart_amba_port *uap = (struct uart_amba_port *)port;
+	struct uart_amba_port *uap =
+	    container_of(port, struct uart_amba_port, port);
 	int retval;
 
 	/* Optionaly enable pins to be muxed in and configured */
@@ -1526,7 +1539,8 @@
 
 static int pl011_startup(struct uart_port *port)
 {
-	struct uart_amba_port *uap = (struct uart_amba_port *)port;
+	struct uart_amba_port *uap =
+	    container_of(port, struct uart_amba_port, port);
 	unsigned int cr, lcr_h, fbrd, ibrd;
 	int retval;
 
@@ -1618,7 +1632,8 @@
 
 static void pl011_shutdown(struct uart_port *port)
 {
-	struct uart_amba_port *uap = (struct uart_amba_port *)port;
+	struct uart_amba_port *uap =
+	    container_of(port, struct uart_amba_port, port);
 	unsigned int cr;
 
 	/*
@@ -1680,7 +1695,8 @@
 pl011_set_termios(struct uart_port *port, struct ktermios *termios,
 		     struct ktermios *old)
 {
-	struct uart_amba_port *uap = (struct uart_amba_port *)port;
+	struct uart_amba_port *uap =
+	    container_of(port, struct uart_amba_port, port);
 	unsigned int lcr_h, old_cr;
 	unsigned long flags;
 	unsigned int baud, quot, clkdiv;
@@ -1822,7 +1838,8 @@
 
 static const char *pl011_type(struct uart_port *port)
 {
-	struct uart_amba_port *uap = (struct uart_amba_port *)port;
+	struct uart_amba_port *uap =
+	    container_of(port, struct uart_amba_port, port);
 	return uap->port.type == PORT_AMBA ? uap->type : NULL;
 }
 
@@ -1900,7 +1917,8 @@
 
 static void pl011_console_putchar(struct uart_port *port, int ch)
 {
-	struct uart_amba_port *uap = (struct uart_amba_port *)port;
+	struct uart_amba_port *uap =
+	    container_of(port, struct uart_amba_port, port);
 
 	while (readw(uap->port.membase + UART01x_FR) & UART01x_FR_TXFF)
 		barrier();
diff --git a/drivers/tty/serial/bfin_sport_uart.c b/drivers/tty/serial/bfin_sport_uart.c
index 7810aa2..d62d8da 100644
--- a/drivers/tty/serial/bfin_sport_uart.c
+++ b/drivers/tty/serial/bfin_sport_uart.c
@@ -33,6 +33,7 @@
 #include <linux/tty.h>
 #include <linux/tty_flip.h>
 #include <linux/serial_core.h>
+#include <linux/gpio.h>
 
 #include <asm/bfin_sport.h>
 #include <asm/delay.h>
diff --git a/drivers/tty/serial/bfin_uart.c b/drivers/tty/serial/bfin_uart.c
index dec0fd7..7da9911 100644
--- a/drivers/tty/serial/bfin_uart.c
+++ b/drivers/tty/serial/bfin_uart.c
@@ -108,22 +108,23 @@
 static irqreturn_t bfin_serial_mctrl_cts_int(int irq, void *dev_id)
 {
 	struct bfin_serial_port *uart = dev_id;
-	unsigned int status = bfin_serial_get_mctrl(&uart->port);
+	struct uart_port *uport = &uart->port;
+	unsigned int status = bfin_serial_get_mctrl(uport);
 #ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
-	struct tty_struct *tty = uart->port.state->port.tty;
 
 	UART_CLEAR_SCTS(uart);
-	if (tty->hw_stopped) {
+	if (uport->hw_stopped) {
 		if (status) {
-			tty->hw_stopped = 0;
-			uart_write_wakeup(&uart->port);
+			uport->hw_stopped = 0;
+			uart_write_wakeup(uport);
 		}
 	} else {
 		if (!status)
-			tty->hw_stopped = 1;
+			uport->hw_stopped = 1;
 	}
+#else
+	uart_handle_cts_change(uport, status & TIOCM_CTS);
 #endif
-	uart_handle_cts_change(&uart->port, status & TIOCM_CTS);
 
 	return IRQ_HANDLED;
 }
diff --git a/drivers/tty/serial/clps711x.c b/drivers/tty/serial/clps711x.c
index f5b4c3d..acfe317 100644
--- a/drivers/tty/serial/clps711x.c
+++ b/drivers/tty/serial/clps711x.c
@@ -33,6 +33,8 @@
 #include <linux/mfd/syscon.h>
 #include <linux/mfd/syscon/clps711x.h>
 
+#include "serial_mctrl_gpio.h"
+
 #define UART_CLPS711X_DEVNAME	"ttyCL"
 #define UART_CLPS711X_NR	2
 #define UART_CLPS711X_MAJOR	204
@@ -62,7 +64,7 @@
 	unsigned int		tx_enabled;
 	int			rx_irq;
 	struct regmap		*syscon;
-	bool			use_ms;
+	struct mctrl_gpios	*gpios;
 };
 
 static struct uart_driver clps711x_uart = {
@@ -198,28 +200,17 @@
 
 static unsigned int uart_clps711x_get_mctrl(struct uart_port *port)
 {
+	unsigned int result = TIOCM_DSR | TIOCM_CTS | TIOCM_CAR;
 	struct clps711x_port *s = dev_get_drvdata(port->dev);
-	unsigned int result = 0;
 
-	if (s->use_ms) {
-		u32 sysflg = 0;
-
-		regmap_read(s->syscon, SYSFLG_OFFSET, &sysflg);
-		if (sysflg & SYSFLG1_DCD)
-			result |= TIOCM_CAR;
-		if (sysflg & SYSFLG1_DSR)
-			result |= TIOCM_DSR;
-		if (sysflg & SYSFLG1_CTS)
-			result |= TIOCM_CTS;
-	} else
-		result = TIOCM_DSR | TIOCM_CTS | TIOCM_CAR;
-
-	return result;
+	return mctrl_gpio_get(s->gpios, &result);
 }
 
 static void uart_clps711x_set_mctrl(struct uart_port *port, unsigned int mctrl)
 {
-	/* Do nothing */
+	struct clps711x_port *s = dev_get_drvdata(port->dev);
+
+	mctrl_gpio_set(s->gpios, mctrl);
 }
 
 static void uart_clps711x_break_ctl(struct uart_port *port, int break_state)
@@ -490,15 +481,10 @@
 		s->syscon = syscon_regmap_lookup_by_pdevname(syscon_name);
 		if (IS_ERR(s->syscon))
 			return PTR_ERR(s->syscon);
-
-		s->use_ms = !index;
 	} else {
 		s->syscon = syscon_regmap_lookup_by_phandle(np, "syscon");
 		if (IS_ERR(s->syscon))
 			return PTR_ERR(s->syscon);
-
-		if (!index)
-			s->use_ms = of_property_read_bool(np, "uart-use-ms");
 	}
 
 	s->port.line		= index;
@@ -513,6 +499,8 @@
 
 	platform_set_drvdata(pdev, s);
 
+	s->gpios = mctrl_gpio_init(&pdev->dev, 0);
+
 	ret = uart_add_one_port(&clps711x_uart, &s->port);
 	if (ret)
 		return ret;
diff --git a/drivers/tty/serial/imx.c b/drivers/tty/serial/imx.c
index 044e86d..8f62a3c 100644
--- a/drivers/tty/serial/imx.c
+++ b/drivers/tty/serial/imx.c
@@ -80,6 +80,7 @@
 #define URXD_FRMERR	(1<<12)
 #define URXD_BRK	(1<<11)
 #define URXD_PRERR	(1<<10)
+#define URXD_RX_DATA	(0xFF<<0)
 #define UCR1_ADEN	(1<<15) /* Auto detect interrupt */
 #define UCR1_ADBR	(1<<14) /* Auto detect baud rate */
 #define UCR1_TRDYEN	(1<<13) /* Transmitter ready interrupt enable */
@@ -435,12 +436,14 @@
 	struct imx_port *sport = (struct imx_port *)port;
 	unsigned long temp;
 
-	/*
-	 * We are maybe in the SMP context, so if the DMA TX thread is running
-	 * on other cpu, we have to wait for it to finish.
-	 */
-	if (sport->dma_is_enabled && sport->dma_is_rxing)
-		return;
+	if (sport->dma_is_enabled && sport->dma_is_rxing) {
+		if (sport->port.suspended) {
+			dmaengine_terminate_all(sport->dma_chan_rx);
+			sport->dma_is_rxing = 0;
+		} else {
+			return;
+		}
+	}
 
 	temp = readl(sport->port.membase + UCR2);
 	writel(temp & ~UCR2_RXEN, sport->port.membase + UCR2);
@@ -464,9 +467,19 @@
 {
 	struct circ_buf *xmit = &sport->port.state->xmit;
 
+	if (sport->port.x_char) {
+		/* Send next char */
+		writel(sport->port.x_char, sport->port.membase + URTX0);
+		return;
+	}
+
+	if (uart_circ_empty(xmit) || uart_tx_stopped(&sport->port)) {
+		imx_stop_tx(&sport->port);
+		return;
+	}
+
 	while (!uart_circ_empty(xmit) &&
-			!(readl(sport->port.membase + uts_reg(sport))
-				& UTS_TXFULL)) {
+	       !(readl(sport->port.membase + uts_reg(sport)) & UTS_TXFULL)) {
 		/* send xmit->buf[xmit->tail]
 		 * out the port here */
 		writel(xmit->buf[xmit->tail], sport->port.membase + URTX0);
@@ -567,9 +580,6 @@
 	struct imx_port *sport = (struct imx_port *)port;
 	unsigned long temp;
 
-	if (uart_circ_empty(&port->state->xmit))
-		return;
-
 	if (USE_IRDA(sport)) {
 		/* half duplex in IrDA mode; have to disable receive mode */
 		temp = readl(sport->port.membase + UCR4);
@@ -604,7 +614,10 @@
 	}
 
 	if (sport->dma_is_enabled) {
-		imx_dma_tx(sport);
+		/* FIXME: port->x_char must be transmitted if != 0 */
+		if (!uart_circ_empty(&port->state->xmit) &&
+		    !uart_tx_stopped(port))
+			imx_dma_tx(sport);
 		return;
 	}
 
@@ -632,27 +645,10 @@
 static irqreturn_t imx_txint(int irq, void *dev_id)
 {
 	struct imx_port *sport = dev_id;
-	struct circ_buf *xmit = &sport->port.state->xmit;
 	unsigned long flags;
 
 	spin_lock_irqsave(&sport->port.lock, flags);
-	if (sport->port.x_char) {
-		/* Send next char */
-		writel(sport->port.x_char, sport->port.membase + URTX0);
-		goto out;
-	}
-
-	if (uart_circ_empty(xmit) || uart_tx_stopped(&sport->port)) {
-		imx_stop_tx(&sport->port);
-		goto out;
-	}
-
 	imx_transmit_buffer(sport);
-
-	if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
-		uart_write_wakeup(&sport->port);
-
-out:
 	spin_unlock_irqrestore(&sport->port.lock, flags);
 	return IRQ_HANDLED;
 }
@@ -823,11 +819,9 @@
 	struct imx_port *sport = (struct imx_port *)port;
 	unsigned long temp;
 
-	temp = readl(sport->port.membase + UCR2) & ~UCR2_CTS;
-
+	temp = readl(sport->port.membase + UCR2) & ~(UCR2_CTS | UCR2_CTSC);
 	if (mctrl & TIOCM_RTS)
-		if (!sport->dma_is_enabled)
-			temp |= UCR2_CTS;
+		temp |= UCR2_CTS | UCR2_CTSC;
 
 	writel(temp, sport->port.membase + UCR2);
 
@@ -1225,9 +1219,18 @@
 	unsigned long flags;
 
 	if (sport->dma_is_enabled) {
+		int ret;
+
 		/* We have to wait for the DMA to finish. */
-		wait_event(sport->dma_wait,
+		ret = wait_event_interruptible(sport->dma_wait,
 			!sport->dma_is_rxing && !sport->dma_is_txing);
+		if (ret != 0) {
+			sport->dma_is_rxing = 0;
+			sport->dma_is_txing = 0;
+			dmaengine_terminate_all(sport->dma_chan_tx);
+			dmaengine_terminate_all(sport->dma_chan_rx);
+		}
+		imx_stop_tx(port);
 		imx_stop_rx(port);
 		imx_disable_dma(sport);
 		imx_uart_dma_exit(sport);
@@ -1506,32 +1509,10 @@
 #if defined(CONFIG_CONSOLE_POLL)
 static int imx_poll_get_char(struct uart_port *port)
 {
-	struct imx_port_ucrs old_ucr;
-	unsigned int status;
-	unsigned char c;
+	if (!(readl(port->membase + USR2) & USR2_RDR))
+		return NO_POLL_CHAR;
 
-	/* save control registers */
-	imx_port_ucrs_save(port, &old_ucr);
-
-	/* disable interrupts */
-	writel(UCR1_UARTEN, port->membase + UCR1);
-	writel(old_ucr.ucr2 & ~(UCR2_ATEN | UCR2_RTSEN | UCR2_ESCI),
-	       port->membase + UCR2);
-	writel(old_ucr.ucr3 & ~(UCR3_DCD | UCR3_RI | UCR3_DTREN),
-	       port->membase + UCR3);
-
-	/* poll */
-	do {
-		status = readl(port->membase + USR2);
-	} while (~status & USR2_RDR);
-
-	/* read */
-	c = readl(port->membase + URXD0);
-
-	/* restore control registers */
-	imx_port_ucrs_restore(port, &old_ucr);
-
-	return c;
+	return readl(port->membase + URXD0) & URXD_RX_DATA;
 }
 
 static void imx_poll_put_char(struct uart_port *port, unsigned char c)
diff --git a/drivers/tty/serial/jsm/jsm.h b/drivers/tty/serial/jsm/jsm.h
index 844d5e4..af70134 100644
--- a/drivers/tty/serial/jsm/jsm.h
+++ b/drivers/tty/serial/jsm/jsm.h
@@ -67,6 +67,16 @@
 #define MAXPORTS	8
 #define MAX_STOPS_SENT	5
 
+/* Board ids */
+#define PCI_DEVICE_ID_NEO_4             0x00B0
+#define PCI_DEVICE_ID_NEO_1_422         0x00CC
+#define PCI_DEVICE_ID_NEO_1_422_485     0x00CD
+#define PCI_DEVICE_ID_NEO_2_422_485     0x00CE
+#define PCIE_DEVICE_ID_NEO_8            0x00F0
+#define PCIE_DEVICE_ID_NEO_4            0x00F1
+#define PCIE_DEVICE_ID_NEO_4RJ45        0x00F2
+#define PCIE_DEVICE_ID_NEO_8RJ45        0x00F3
+
 /* Board type definitions */
 
 #define T_NEO		0000
diff --git a/drivers/tty/serial/jsm/jsm_driver.c b/drivers/tty/serial/jsm/jsm_driver.c
index a47d882..d2885a7 100644
--- a/drivers/tty/serial/jsm/jsm_driver.c
+++ b/drivers/tty/serial/jsm/jsm_driver.c
@@ -93,12 +93,34 @@
 	/* store the info for the board we've found */
 	brd->boardnum = adapter_count++;
 	brd->pci_dev = pdev;
-	if (pdev->device == PCIE_DEVICE_ID_NEO_4_IBM)
-		brd->maxports = 4;
-	else if (pdev->device == PCI_DEVICE_ID_DIGI_NEO_8)
-		brd->maxports = 8;
-	else
+
+	switch (pdev->device) {
+
+	case PCI_DEVICE_ID_NEO_2DB9:
+	case PCI_DEVICE_ID_NEO_2DB9PRI:
+	case PCI_DEVICE_ID_NEO_2RJ45:
+	case PCI_DEVICE_ID_NEO_2RJ45PRI:
+	case PCI_DEVICE_ID_NEO_2_422_485:
 		brd->maxports = 2;
+		break;
+
+	case PCI_DEVICE_ID_NEO_4:
+	case PCIE_DEVICE_ID_NEO_4:
+	case PCIE_DEVICE_ID_NEO_4RJ45:
+	case PCIE_DEVICE_ID_NEO_4_IBM:
+		brd->maxports = 4;
+		break;
+
+	case PCI_DEVICE_ID_DIGI_NEO_8:
+	case PCIE_DEVICE_ID_NEO_8:
+	case PCIE_DEVICE_ID_NEO_8RJ45:
+		brd->maxports = 8;
+		break;
+
+	default:
+		brd->maxports = 1;
+		break;
+	}
 
 	spin_lock_init(&brd->bd_intr_lock);
 
@@ -209,6 +231,14 @@
 	{ PCI_DEVICE(PCI_VENDOR_ID_DIGI, PCI_DEVICE_ID_NEO_2RJ45PRI), 0, 0, 3 },
 	{ PCI_DEVICE(PCI_VENDOR_ID_DIGI, PCIE_DEVICE_ID_NEO_4_IBM), 0, 0, 4 },
 	{ PCI_DEVICE(PCI_VENDOR_ID_DIGI, PCI_DEVICE_ID_DIGI_NEO_8), 0, 0, 5 },
+	{ PCI_DEVICE(PCI_VENDOR_ID_DIGI, PCI_DEVICE_ID_NEO_4), 0, 0, 6 },
+	{ PCI_DEVICE(PCI_VENDOR_ID_DIGI, PCI_DEVICE_ID_NEO_1_422), 0, 0, 7 },
+	{ PCI_DEVICE(PCI_VENDOR_ID_DIGI, PCI_DEVICE_ID_NEO_1_422_485), 0, 0, 8 },
+	{ PCI_DEVICE(PCI_VENDOR_ID_DIGI, PCI_DEVICE_ID_NEO_2_422_485), 0, 0, 9 },
+	{ PCI_DEVICE(PCI_VENDOR_ID_DIGI, PCIE_DEVICE_ID_NEO_8), 0, 0, 10 },
+	{ PCI_DEVICE(PCI_VENDOR_ID_DIGI, PCIE_DEVICE_ID_NEO_4), 0, 0, 11 },
+	{ PCI_DEVICE(PCI_VENDOR_ID_DIGI, PCIE_DEVICE_ID_NEO_4RJ45), 0, 0, 12 },
+	{ PCI_DEVICE(PCI_VENDOR_ID_DIGI, PCIE_DEVICE_ID_NEO_8RJ45), 0, 0, 13 },
 	{ 0, }
 };
 MODULE_DEVICE_TABLE(pci, jsm_pci_tbl);
diff --git a/drivers/tty/serial/kgdb_nmi.c b/drivers/tty/serial/kgdb_nmi.c
index 6ec7501..129dc5b 100644
--- a/drivers/tty/serial/kgdb_nmi.c
+++ b/drivers/tty/serial/kgdb_nmi.c
@@ -46,6 +46,8 @@
 
 static int kgdb_nmi_console_setup(struct console *co, char *options)
 {
+	arch_kgdb_ops.enable_nmi(1);
+
 	/* The NMI console uses the dbg_io_ops to issue console messages. To
 	 * avoid duplicate messages during kdb sessions we must inform kdb's
 	 * I/O utilities that messages sent to the console will automatically
@@ -77,7 +79,7 @@
 	.setup  = kgdb_nmi_console_setup,
 	.write	= kgdb_nmi_console_write,
 	.device	= kgdb_nmi_console_device,
-	.flags	= CON_PRINTBUFFER | CON_ANYTIME | CON_ENABLED,
+	.flags	= CON_PRINTBUFFER | CON_ANYTIME,
 	.index	= -1,
 };
 
@@ -354,7 +356,6 @@
 	}
 
 	register_console(&kgdb_nmi_console);
-	arch_kgdb_ops.enable_nmi(1);
 
 	return 0;
 err_drv_reg:
diff --git a/drivers/tty/serial/meson_uart.c b/drivers/tty/serial/meson_uart.c
new file mode 100644
index 0000000..15c74975
--- /dev/null
+++ b/drivers/tty/serial/meson_uart.c
@@ -0,0 +1,634 @@
+/*
+ *  Based on meson_uart.c, by AMLOGIC, INC.
+ *
+ * Copyright (C) 2014 Carlo Caione <carlo@caione.org>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <linux/clk.h>
+#include <linux/console.h>
+#include <linux/delay.h>
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/serial.h>
+#include <linux/serial_core.h>
+#include <linux/tty.h>
+#include <linux/tty_flip.h>
+
+/* Register offsets */
+#define AML_UART_WFIFO			0x00
+#define AML_UART_RFIFO			0x04
+#define AML_UART_CONTROL		0x08
+#define AML_UART_STATUS			0x0c
+#define AML_UART_MISC			0x10
+#define AML_UART_REG5			0x14
+
+/* AML_UART_CONTROL bits */
+#define AML_UART_TX_EN			BIT(12)
+#define AML_UART_RX_EN			BIT(13)
+#define AML_UART_TX_RST			BIT(22)
+#define AML_UART_RX_RST			BIT(23)
+#define AML_UART_CLR_ERR		BIT(24)
+#define AML_UART_RX_INT_EN		BIT(27)
+#define AML_UART_TX_INT_EN		BIT(28)
+#define AML_UART_DATA_LEN_MASK		(0x03 << 20)
+#define AML_UART_DATA_LEN_8BIT		(0x00 << 20)
+#define AML_UART_DATA_LEN_7BIT		(0x01 << 20)
+#define AML_UART_DATA_LEN_6BIT		(0x02 << 20)
+#define AML_UART_DATA_LEN_5BIT		(0x03 << 20)
+
+/* AML_UART_STATUS bits */
+#define AML_UART_PARITY_ERR		BIT(16)
+#define AML_UART_FRAME_ERR		BIT(17)
+#define AML_UART_TX_FIFO_WERR		BIT(18)
+#define AML_UART_RX_EMPTY		BIT(20)
+#define AML_UART_TX_FULL		BIT(21)
+#define AML_UART_TX_EMPTY		BIT(22)
+#define AML_UART_ERR			(AML_UART_PARITY_ERR | \
+					 AML_UART_FRAME_ERR  | \
+					 AML_UART_TX_FIFO_WERR)
+
+/* AML_UART_CONTROL bits */
+#define AML_UART_TWO_WIRE_EN		BIT(15)
+#define AML_UART_PARITY_TYPE		BIT(18)
+#define AML_UART_PARITY_EN		BIT(19)
+#define AML_UART_CLEAR_ERR		BIT(24)
+#define AML_UART_STOP_BIN_LEN_MASK	(0x03 << 16)
+#define AML_UART_STOP_BIN_1SB		(0x00 << 16)
+#define AML_UART_STOP_BIN_2SB		(0x01 << 16)
+
+/* AML_UART_MISC bits */
+#define AML_UART_XMIT_IRQ(c)		(((c) & 0xff) << 8)
+#define AML_UART_RECV_IRQ(c)		((c) & 0xff)
+
+/* AML_UART_REG5 bits */
+#define AML_UART_BAUD_MASK		0x7fffff
+#define AML_UART_BAUD_USE		BIT(23)
+
+#define AML_UART_PORT_NUM		6
+#define AML_UART_DEV_NAME		"ttyAML"
+
+
+static struct uart_driver meson_uart_driver;
+
+static struct uart_port *meson_ports[AML_UART_PORT_NUM];
+
+static void meson_uart_set_mctrl(struct uart_port *port, unsigned int mctrl)
+{
+}
+
+static unsigned int meson_uart_get_mctrl(struct uart_port *port)
+{
+	return TIOCM_CTS;
+}
+
+static unsigned int meson_uart_tx_empty(struct uart_port *port)
+{
+	u32 val;
+
+	val = readl(port->membase + AML_UART_STATUS);
+	return (val & AML_UART_TX_EMPTY) ? TIOCSER_TEMT : 0;
+}
+
+static void meson_uart_stop_tx(struct uart_port *port)
+{
+	u32 val;
+
+	val = readl(port->membase + AML_UART_CONTROL);
+	val &= ~AML_UART_TX_EN;
+	writel(val, port->membase + AML_UART_CONTROL);
+}
+
+static void meson_uart_stop_rx(struct uart_port *port)
+{
+	u32 val;
+
+	val = readl(port->membase + AML_UART_CONTROL);
+	val &= ~AML_UART_RX_EN;
+	writel(val, port->membase + AML_UART_CONTROL);
+}
+
+static void meson_uart_shutdown(struct uart_port *port)
+{
+	unsigned long flags;
+	u32 val;
+
+	free_irq(port->irq, port);
+
+	spin_lock_irqsave(&port->lock, flags);
+
+	val = readl(port->membase + AML_UART_CONTROL);
+	val &= ~(AML_UART_RX_EN | AML_UART_TX_EN);
+	val &= ~(AML_UART_RX_INT_EN | AML_UART_TX_INT_EN);
+	writel(val, port->membase + AML_UART_CONTROL);
+
+	spin_unlock_irqrestore(&port->lock, flags);
+}
+
+static void meson_uart_start_tx(struct uart_port *port)
+{
+	struct circ_buf *xmit = &port->state->xmit;
+	unsigned int ch;
+
+	if (uart_tx_stopped(port)) {
+		meson_uart_stop_tx(port);
+		return;
+	}
+
+	while (!(readl(port->membase + AML_UART_STATUS) & AML_UART_TX_FULL)) {
+		if (port->x_char) {
+			writel(port->x_char, port->membase + AML_UART_WFIFO);
+			port->icount.tx++;
+			port->x_char = 0;
+			continue;
+		}
+
+		if (uart_circ_empty(xmit))
+			break;
+
+		ch = xmit->buf[xmit->tail];
+		writel(ch, port->membase + AML_UART_WFIFO);
+		xmit->tail = (xmit->tail+1) & (SERIAL_XMIT_SIZE - 1);
+		port->icount.tx++;
+	}
+
+	if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+		uart_write_wakeup(port);
+}
+
+static void meson_receive_chars(struct uart_port *port)
+{
+	struct tty_port *tport = &port->state->port;
+	char flag;
+	u32 status, ch, mode;
+
+	do {
+		flag = TTY_NORMAL;
+		port->icount.rx++;
+		status = readl(port->membase + AML_UART_STATUS);
+
+		if (status & AML_UART_ERR) {
+			if (status & AML_UART_TX_FIFO_WERR)
+				port->icount.overrun++;
+			else if (status & AML_UART_FRAME_ERR)
+				port->icount.frame++;
+			else if (status & AML_UART_PARITY_ERR)
+				port->icount.frame++;
+
+			mode = readl(port->membase + AML_UART_CONTROL);
+			mode |= AML_UART_CLEAR_ERR;
+			writel(mode, port->membase + AML_UART_CONTROL);
+
+			/* It doesn't clear to 0 automatically */
+			mode &= ~AML_UART_CLEAR_ERR;
+			writel(mode, port->membase + AML_UART_CONTROL);
+
+			status &= port->read_status_mask;
+			if (status & AML_UART_FRAME_ERR)
+				flag = TTY_FRAME;
+			else if (status & AML_UART_PARITY_ERR)
+				flag = TTY_PARITY;
+		}
+
+		ch = readl(port->membase + AML_UART_RFIFO);
+		ch &= 0xff;
+
+		if ((status & port->ignore_status_mask) == 0)
+			tty_insert_flip_char(tport, ch, flag);
+
+		if (status & AML_UART_TX_FIFO_WERR)
+			tty_insert_flip_char(tport, 0, TTY_OVERRUN);
+
+	} while (!(readl(port->membase + AML_UART_STATUS) & AML_UART_RX_EMPTY));
+
+	spin_unlock(&port->lock);
+	tty_flip_buffer_push(tport);
+	spin_lock(&port->lock);
+}
+
+static irqreturn_t meson_uart_interrupt(int irq, void *dev_id)
+{
+	struct uart_port *port = (struct uart_port *)dev_id;
+
+	spin_lock(&port->lock);
+
+	if (!(readl(port->membase + AML_UART_STATUS) & AML_UART_RX_EMPTY))
+		meson_receive_chars(port);
+
+	if (!(readl(port->membase + AML_UART_STATUS) & AML_UART_TX_FULL))
+		meson_uart_start_tx(port);
+
+	spin_unlock(&port->lock);
+
+	return IRQ_HANDLED;
+}
+
+static const char *meson_uart_type(struct uart_port *port)
+{
+	return (port->type == PORT_MESON) ? "meson_uart" : NULL;
+}
+
+static int meson_uart_startup(struct uart_port *port)
+{
+	u32 val;
+	int ret = 0;
+
+	val = readl(port->membase + AML_UART_CONTROL);
+	val |= (AML_UART_RX_RST | AML_UART_TX_RST | AML_UART_CLR_ERR);
+	writel(val, port->membase + AML_UART_CONTROL);
+
+	val &= ~(AML_UART_RX_RST | AML_UART_TX_RST | AML_UART_CLR_ERR);
+	writel(val, port->membase + AML_UART_CONTROL);
+
+	val |= (AML_UART_RX_EN | AML_UART_TX_EN);
+	writel(val, port->membase + AML_UART_CONTROL);
+
+	val |= (AML_UART_RX_INT_EN | AML_UART_TX_INT_EN);
+	writel(val, port->membase + AML_UART_CONTROL);
+
+	val = (AML_UART_RECV_IRQ(1) | AML_UART_XMIT_IRQ(port->fifosize / 2));
+	writel(val, port->membase + AML_UART_MISC);
+
+	ret = request_irq(port->irq, meson_uart_interrupt, 0,
+			  meson_uart_type(port), port);
+
+	return ret;
+}
+
+static void meson_uart_change_speed(struct uart_port *port, unsigned long baud)
+{
+	u32 val;
+
+	while (!(readl(port->membase + AML_UART_STATUS) & AML_UART_TX_EMPTY))
+		cpu_relax();
+
+	val = readl(port->membase + AML_UART_REG5);
+	val &= ~AML_UART_BAUD_MASK;
+	val = ((port->uartclk * 10 / (baud * 4) + 5) / 10) - 1;
+	val |= AML_UART_BAUD_USE;
+	writel(val, port->membase + AML_UART_REG5);
+}
+
+static void meson_uart_set_termios(struct uart_port *port,
+				   struct ktermios *termios,
+				   struct ktermios *old)
+{
+	unsigned int cflags, iflags, baud;
+	unsigned long flags;
+	u32 val;
+
+	spin_lock_irqsave(&port->lock, flags);
+
+	cflags = termios->c_cflag;
+	iflags = termios->c_iflag;
+
+	val = readl(port->membase + AML_UART_CONTROL);
+
+	val &= ~AML_UART_DATA_LEN_MASK;
+	switch (cflags & CSIZE) {
+	case CS8:
+		val |= AML_UART_DATA_LEN_8BIT;
+		break;
+	case CS7:
+		val |= AML_UART_DATA_LEN_7BIT;
+		break;
+	case CS6:
+		val |= AML_UART_DATA_LEN_6BIT;
+		break;
+	case CS5:
+		val |= AML_UART_DATA_LEN_5BIT;
+		break;
+	}
+
+	if (cflags & PARENB)
+		val |= AML_UART_PARITY_EN;
+	else
+		val &= ~AML_UART_PARITY_EN;
+
+	if (cflags & PARODD)
+		val |= AML_UART_PARITY_TYPE;
+	else
+		val &= ~AML_UART_PARITY_TYPE;
+
+	val &= ~AML_UART_STOP_BIN_LEN_MASK;
+	if (cflags & CSTOPB)
+		val |= AML_UART_STOP_BIN_2SB;
+	else
+		val &= ~AML_UART_STOP_BIN_1SB;
+
+	if (cflags & CRTSCTS)
+		val &= ~AML_UART_TWO_WIRE_EN;
+	else
+		val |= AML_UART_TWO_WIRE_EN;
+
+	writel(val, port->membase + AML_UART_CONTROL);
+
+	baud = uart_get_baud_rate(port, termios, old, 9600, 115200);
+	meson_uart_change_speed(port, baud);
+
+	port->read_status_mask = AML_UART_TX_FIFO_WERR;
+	if (iflags & INPCK)
+		port->read_status_mask |= AML_UART_PARITY_ERR |
+					  AML_UART_FRAME_ERR;
+
+	port->ignore_status_mask = 0;
+	if (iflags & IGNPAR)
+		port->ignore_status_mask |= AML_UART_PARITY_ERR |
+					    AML_UART_FRAME_ERR;
+
+	uart_update_timeout(port, termios->c_cflag, baud);
+	spin_unlock_irqrestore(&port->lock, flags);
+}
+
+static int meson_uart_verify_port(struct uart_port *port,
+				  struct serial_struct *ser)
+{
+	int ret = 0;
+
+	if (port->type != PORT_MESON)
+		ret = -EINVAL;
+	if (port->irq != ser->irq)
+		ret = -EINVAL;
+	if (ser->baud_base < 9600)
+		ret = -EINVAL;
+	return ret;
+}
+
+static void meson_uart_release_port(struct uart_port *port)
+{
+	if (port->flags & UPF_IOREMAP) {
+		iounmap(port->membase);
+		port->membase = NULL;
+	}
+}
+
+static int meson_uart_request_port(struct uart_port *port)
+{
+	struct platform_device *pdev = to_platform_device(port->dev);
+	struct resource *res;
+	int size;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res) {
+		dev_err(&pdev->dev, "cannot obtain I/O memory region");
+		return -ENODEV;
+	}
+	size = resource_size(res);
+
+	if (!devm_request_mem_region(port->dev, port->mapbase, size,
+				     dev_name(port->dev))) {
+		dev_err(port->dev, "Memory region busy\n");
+		return -EBUSY;
+	}
+
+	if (port->flags & UPF_IOREMAP) {
+		port->membase = devm_ioremap_nocache(port->dev,
+						     port->mapbase,
+						     size);
+		if (port->membase == NULL)
+			return -ENOMEM;
+	}
+
+	return 0;
+}
+
+static void meson_uart_config_port(struct uart_port *port, int flags)
+{
+	if (flags & UART_CONFIG_TYPE) {
+		port->type = PORT_MESON;
+		meson_uart_request_port(port);
+	}
+}
+
+static struct uart_ops meson_uart_ops = {
+	.set_mctrl      = meson_uart_set_mctrl,
+	.get_mctrl      = meson_uart_get_mctrl,
+	.tx_empty	= meson_uart_tx_empty,
+	.start_tx	= meson_uart_start_tx,
+	.stop_tx	= meson_uart_stop_tx,
+	.stop_rx	= meson_uart_stop_rx,
+	.startup	= meson_uart_startup,
+	.shutdown	= meson_uart_shutdown,
+	.set_termios	= meson_uart_set_termios,
+	.type		= meson_uart_type,
+	.config_port	= meson_uart_config_port,
+	.request_port	= meson_uart_request_port,
+	.release_port	= meson_uart_release_port,
+	.verify_port	= meson_uart_verify_port,
+};
+
+#ifdef CONFIG_SERIAL_MESON_CONSOLE
+
+static void meson_console_putchar(struct uart_port *port, int ch)
+{
+	if (!port->membase)
+		return;
+
+	while (readl(port->membase + AML_UART_STATUS) & AML_UART_TX_FULL)
+		cpu_relax();
+	writel(ch, port->membase + AML_UART_WFIFO);
+}
+
+static void meson_serial_console_write(struct console *co, const char *s,
+				       u_int count)
+{
+	struct uart_port *port;
+	unsigned long flags;
+	int locked;
+
+	port = meson_ports[co->index];
+	if (!port)
+		return;
+
+	local_irq_save(flags);
+	if (port->sysrq) {
+		locked = 0;
+	} else if (oops_in_progress) {
+		locked = spin_trylock(&port->lock);
+	} else {
+		spin_lock(&port->lock);
+		locked = 1;
+	}
+
+	uart_console_write(port, s, count, meson_console_putchar);
+
+	if (locked)
+		spin_unlock(&port->lock);
+	local_irq_restore(flags);
+}
+
+static int meson_serial_console_setup(struct console *co, char *options)
+{
+	struct uart_port *port;
+	int baud = 115200;
+	int bits = 8;
+	int parity = 'n';
+	int flow = 'n';
+
+	if (co->index < 0 || co->index >= AML_UART_PORT_NUM)
+		return -EINVAL;
+
+	port = meson_ports[co->index];
+	if (!port || !port->membase)
+		return -ENODEV;
+
+	if (options)
+		uart_parse_options(options, &baud, &parity, &bits, &flow);
+
+	return uart_set_options(port, co, baud, parity, bits, flow);
+}
+
+static struct console meson_serial_console = {
+	.name		= AML_UART_DEV_NAME,
+	.write		= meson_serial_console_write,
+	.device		= uart_console_device,
+	.setup		= meson_serial_console_setup,
+	.flags		= CON_PRINTBUFFER,
+	.index		= -1,
+	.data		= &meson_uart_driver,
+};
+
+static int __init meson_serial_console_init(void)
+{
+	register_console(&meson_serial_console);
+	return 0;
+}
+console_initcall(meson_serial_console_init);
+
+#define MESON_SERIAL_CONSOLE	(&meson_serial_console)
+#else
+#define MESON_SERIAL_CONSOLE	NULL
+#endif
+
+static struct uart_driver meson_uart_driver = {
+	.owner		= THIS_MODULE,
+	.driver_name	= "meson_uart",
+	.dev_name	= AML_UART_DEV_NAME,
+	.nr		= AML_UART_PORT_NUM,
+	.cons		= MESON_SERIAL_CONSOLE,
+};
+
+static int meson_uart_probe(struct platform_device *pdev)
+{
+	struct resource *res_mem, *res_irq;
+	struct uart_port *port;
+	struct clk *clk;
+	int ret = 0;
+
+	if (pdev->dev.of_node)
+		pdev->id = of_alias_get_id(pdev->dev.of_node, "serial");
+
+	if (pdev->id < 0 || pdev->id >= AML_UART_PORT_NUM)
+		return -EINVAL;
+
+	res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res_mem)
+		return -ENODEV;
+
+	res_irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
+	if (!res_irq)
+		return -ENODEV;
+
+	if (meson_ports[pdev->id]) {
+		dev_err(&pdev->dev, "port %d already allocated\n", pdev->id);
+		return -EBUSY;
+	}
+
+	port = devm_kzalloc(&pdev->dev, sizeof(struct uart_port), GFP_KERNEL);
+	if (!port)
+		return -ENOMEM;
+
+	clk = clk_get(&pdev->dev, NULL);
+	if (IS_ERR(clk))
+		return PTR_ERR(clk);
+
+	port->uartclk = clk_get_rate(clk);
+	port->iotype = UPIO_MEM;
+	port->mapbase = res_mem->start;
+	port->irq = res_irq->start;
+	port->flags = UPF_BOOT_AUTOCONF | UPF_IOREMAP | UPF_LOW_LATENCY;
+	port->dev = &pdev->dev;
+	port->line = pdev->id;
+	port->type = PORT_MESON;
+	port->x_char = 0;
+	port->ops = &meson_uart_ops;
+	port->fifosize = 64;
+
+	meson_ports[pdev->id] = port;
+	platform_set_drvdata(pdev, port);
+
+	ret = uart_add_one_port(&meson_uart_driver, port);
+	if (ret)
+		meson_ports[pdev->id] = NULL;
+
+	return ret;
+}
+
+static int meson_uart_remove(struct platform_device *pdev)
+{
+	struct uart_port *port;
+
+	port = platform_get_drvdata(pdev);
+	uart_remove_one_port(&meson_uart_driver, port);
+	meson_ports[pdev->id] = NULL;
+
+	return 0;
+}
+
+
+static const struct of_device_id meson_uart_dt_match[] = {
+	{ .compatible = "amlogic,meson-uart" },
+	{ /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, meson_uart_dt_match);
+
+static  struct platform_driver meson_uart_platform_driver = {
+	.probe		= meson_uart_probe,
+	.remove		= meson_uart_remove,
+	.driver		= {
+		.owner		= THIS_MODULE,
+		.name		= "meson_uart",
+		.of_match_table	= meson_uart_dt_match,
+	},
+};
+
+static int __init meson_uart_init(void)
+{
+	int ret;
+
+	ret = uart_register_driver(&meson_uart_driver);
+	if (ret)
+		return ret;
+
+	ret = platform_driver_register(&meson_uart_platform_driver);
+	if (ret)
+		uart_unregister_driver(&meson_uart_driver);
+
+	return ret;
+}
+
+static void __exit meson_uart_exit(void)
+{
+	platform_driver_unregister(&meson_uart_platform_driver);
+	uart_unregister_driver(&meson_uart_driver);
+}
+
+module_init(meson_uart_init);
+module_exit(meson_uart_exit);
+
+MODULE_AUTHOR("Carlo Caione <carlo@caione.org>");
+MODULE_DESCRIPTION("Amlogic Meson serial port driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/tty/serial/mpc52xx_uart.c b/drivers/tty/serial/mpc52xx_uart.c
index 97888f4..a5f4e36 100644
--- a/drivers/tty/serial/mpc52xx_uart.c
+++ b/drivers/tty/serial/mpc52xx_uart.c
@@ -1087,22 +1087,6 @@
 }
 
 static void
-mpc52xx_uart_send_xchar(struct uart_port *port, char ch)
-{
-	unsigned long flags;
-	spin_lock_irqsave(&port->lock, flags);
-
-	port->x_char = ch;
-	if (ch) {
-		/* Make sure tx interrupts are on */
-		/* Truly necessary ??? They should be anyway */
-		psc_ops->start_tx(port);
-	}
-
-	spin_unlock_irqrestore(&port->lock, flags);
-}
-
-static void
 mpc52xx_uart_stop_rx(struct uart_port *port)
 {
 	/* port->lock taken by caller */
@@ -1361,7 +1345,6 @@
 	.get_mctrl	= mpc52xx_uart_get_mctrl,
 	.stop_tx	= mpc52xx_uart_stop_tx,
 	.start_tx	= mpc52xx_uart_start_tx,
-	.send_xchar	= mpc52xx_uart_send_xchar,
 	.stop_rx	= mpc52xx_uart_stop_rx,
 	.enable_ms	= mpc52xx_uart_enable_ms,
 	.break_ctl	= mpc52xx_uart_break_ctl,
diff --git a/drivers/tty/serial/msm_serial.c b/drivers/tty/serial/msm_serial.c
index 0da0b54..4b6c783 100644
--- a/drivers/tty/serial/msm_serial.c
+++ b/drivers/tty/serial/msm_serial.c
@@ -190,11 +190,10 @@
 		/* Mask conditions we're ignorning. */
 		sr &= port->read_status_mask;
 
-		if (sr & UART_SR_RX_BREAK) {
+		if (sr & UART_SR_RX_BREAK)
 			flag = TTY_BREAK;
-		} else if (sr & UART_SR_PAR_FRAME_ERR) {
+		else if (sr & UART_SR_PAR_FRAME_ERR)
 			flag = TTY_FRAME;
-		}
 
 		if (!uart_handle_sysrq_char(port, c))
 			tty_insert_flip_char(tport, c, flag);
@@ -315,7 +314,6 @@
 	return TIOCM_CAR | TIOCM_CTS | TIOCM_DSR | TIOCM_RTS;
 }
 
-
 static void msm_reset(struct uart_port *port)
 {
 	struct msm_port *msm_port = UART_TO_MSM(port);
@@ -336,6 +334,7 @@
 static void msm_set_mctrl(struct uart_port *port, unsigned int mctrl)
 {
 	unsigned int mr;
+
 	mr = msm_read(port, UART_MR1);
 
 	if (!(mctrl & TIOCM_RTS)) {
@@ -431,7 +430,6 @@
 	return baud;
 }
 
-
 static void msm_init_clock(struct uart_port *port)
 {
 	struct msm_port *msm_port = UART_TO_MSM(port);
@@ -646,6 +644,7 @@
 static void msm_config_port(struct uart_port *port, int flags)
 {
 	int ret;
+
 	if (flags & UART_CONFIG_TYPE) {
 		port->type = PORT_MSM;
 		ret = msm_request_port(port);
@@ -678,22 +677,11 @@
 		clk_disable_unprepare(msm_port->pclk);
 		break;
 	default:
-		printk(KERN_ERR "msm_serial: Unknown PM state %d\n", state);
+		pr_err("msm_serial: Unknown PM state %d\n", state);
 	}
 }
 
 #ifdef CONFIG_CONSOLE_POLL
-static int msm_poll_init(struct uart_port *port)
-{
-	struct msm_port *msm_port = UART_TO_MSM(port);
-
-	/* Enable single character mode on RX FIFO */
-	if (msm_port->is_uartdm >= UARTDM_1P4)
-		msm_write(port, UARTDM_DMEN_RX_SC_ENABLE, UARTDM_DMEN);
-
-	return 0;
-}
-
 static int msm_poll_get_char_single(struct uart_port *port)
 {
 	struct msm_port *msm_port = UART_TO_MSM(port);
@@ -701,11 +689,11 @@
 
 	if (!(msm_read(port, UART_SR) & UART_SR_RX_READY))
 		return NO_POLL_CHAR;
-	else
-		return msm_read(port, rf_reg) & 0xff;
+
+	return msm_read(port, rf_reg) & 0xff;
 }
 
-static int msm_poll_get_char_dm_1p3(struct uart_port *port)
+static int msm_poll_get_char_dm(struct uart_port *port)
 {
 	int c;
 	static u32 slop;
@@ -729,6 +717,10 @@
 			slop = msm_read(port, UARTDM_RF);
 			c = sp[0];
 			count--;
+			msm_write(port, UART_CR_CMD_RESET_STALE_INT, UART_CR);
+			msm_write(port, 0xFFFFFF, UARTDM_DMRX);
+			msm_write(port, UART_CR_CMD_STALE_EVENT_ENABLE,
+				  UART_CR);
 		} else {
 			c = NO_POLL_CHAR;
 		}
@@ -752,8 +744,8 @@
 	imr = msm_read(port, UART_IMR);
 	msm_write(port, 0, UART_IMR);
 
-	if (msm_port->is_uartdm == UARTDM_1P3)
-		c = msm_poll_get_char_dm_1p3(port);
+	if (msm_port->is_uartdm)
+		c = msm_poll_get_char_dm(port);
 	else
 		c = msm_poll_get_char_single(port);
 
@@ -788,8 +780,6 @@
 
 	/* Enable interrupts */
 	msm_write(port, imr, UART_IMR);
-
-	return;
 }
 #endif
 
@@ -812,7 +802,6 @@
 	.verify_port = msm_verify_port,
 	.pm = msm_power,
 #ifdef CONFIG_CONSOLE_POLL
-	.poll_init = msm_poll_init,
 	.poll_get_char	= msm_poll_get_char,
 	.poll_put_char	= msm_poll_put_char,
 #endif
@@ -856,22 +845,15 @@
 }
 
 #ifdef CONFIG_SERIAL_MSM_CONSOLE
-static void msm_console_write(struct console *co, const char *s,
-			      unsigned int count)
+static void __msm_console_write(struct uart_port *port, const char *s,
+				unsigned int count, bool is_uartdm)
 {
 	int i;
-	struct uart_port *port;
-	struct msm_port *msm_port;
 	int num_newlines = 0;
 	bool replaced = false;
 	void __iomem *tf;
 
-	BUG_ON(co->index < 0 || co->index >= UART_NR);
-
-	port = get_port_from_line(co->index);
-	msm_port = UART_TO_MSM(port);
-
-	if (msm_port->is_uartdm)
+	if (is_uartdm)
 		tf = port->membase + UARTDM_TF;
 	else
 		tf = port->membase + UART_TF;
@@ -883,7 +865,7 @@
 	count += num_newlines;
 
 	spin_lock(&port->lock);
-	if (msm_port->is_uartdm)
+	if (is_uartdm)
 		reset_dm_count(port, count);
 
 	i = 0;
@@ -892,7 +874,7 @@
 		unsigned int num_chars;
 		char buf[4] = { 0 };
 
-		if (msm_port->is_uartdm)
+		if (is_uartdm)
 			num_chars = min(count - i, (unsigned int)sizeof(buf));
 		else
 			num_chars = 1;
@@ -921,6 +903,20 @@
 	spin_unlock(&port->lock);
 }
 
+static void msm_console_write(struct console *co, const char *s,
+			      unsigned int count)
+{
+	struct uart_port *port;
+	struct msm_port *msm_port;
+
+	BUG_ON(co->index < 0 || co->index >= UART_NR);
+
+	port = get_port_from_line(co->index);
+	msm_port = UART_TO_MSM(port);
+
+	__msm_console_write(port, s, count, msm_port->is_uartdm);
+}
+
 static int __init msm_console_setup(struct console *co, char *options)
 {
 	struct uart_port *port;
@@ -958,11 +954,54 @@
 		msm_write(port, UART_CR_TX_ENABLE, UART_CR);
 	}
 
-	printk(KERN_INFO "msm_serial: console setup on port #%d\n", port->line);
+	pr_info("msm_serial: console setup on port #%d\n", port->line);
 
 	return uart_set_options(port, co, baud, parity, bits, flow);
 }
 
+static void
+msm_serial_early_write(struct console *con, const char *s, unsigned n)
+{
+	struct earlycon_device *dev = con->data;
+
+	__msm_console_write(&dev->port, s, n, false);
+}
+
+static int __init
+msm_serial_early_console_setup(struct earlycon_device *device, const char *opt)
+{
+	if (!device->port.membase)
+		return -ENODEV;
+
+	device->con->write = msm_serial_early_write;
+	return 0;
+}
+EARLYCON_DECLARE(msm_serial, msm_serial_early_console_setup);
+OF_EARLYCON_DECLARE(msm_serial, "qcom,msm-uart",
+		    msm_serial_early_console_setup);
+
+static void
+msm_serial_early_write_dm(struct console *con, const char *s, unsigned n)
+{
+	struct earlycon_device *dev = con->data;
+
+	__msm_console_write(&dev->port, s, n, true);
+}
+
+static int __init
+msm_serial_early_console_setup_dm(struct earlycon_device *device,
+				  const char *opt)
+{
+	if (!device->port.membase)
+		return -ENODEV;
+
+	device->con->write = msm_serial_early_write_dm;
+	return 0;
+}
+EARLYCON_DECLARE(msm_serial_dm, msm_serial_early_console_setup_dm);
+OF_EARLYCON_DECLARE(msm_serial_dm, "qcom,msm-uartdm",
+		    msm_serial_early_console_setup_dm);
+
 static struct uart_driver msm_uart_driver;
 
 static struct console msm_console = {
@@ -1013,7 +1052,7 @@
 	if (unlikely(pdev->id < 0 || pdev->id >= UART_NR))
 		return -ENXIO;
 
-	printk(KERN_INFO "msm_serial: detected port #%d\n", pdev->id);
+	dev_info(&pdev->dev, "msm_serial: detected port #%d\n", pdev->id);
 
 	port = get_port_from_line(pdev->id);
 	port->dev = &pdev->dev;
@@ -1038,8 +1077,7 @@
 	}
 
 	port->uartclk = clk_get_rate(msm_port->clk);
-	printk(KERN_INFO "uartclk = %d\n", port->uartclk);
-
+	dev_info(&pdev->dev, "uartclk = %d\n", port->uartclk);
 
 	resource = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	if (unlikely(!resource))
@@ -1093,7 +1131,7 @@
 	if (unlikely(ret))
 		uart_unregister_driver(&msm_uart_driver);
 
-	printk(KERN_INFO "msm_serial: driver initialized\n");
+	pr_info("msm_serial: driver initialized\n");
 
 	return ret;
 }
diff --git a/drivers/tty/serial/mxs-auart.c b/drivers/tty/serial/mxs-auart.c
index b5c3292..10c2933 100644
--- a/drivers/tty/serial/mxs-auart.c
+++ b/drivers/tty/serial/mxs-auart.c
@@ -408,7 +408,7 @@
 
 	ctrl &= ~(AUART_CTRL2_RTSEN | AUART_CTRL2_RTS);
 	if (mctrl & TIOCM_RTS) {
-		if (tty_port_cts_enabled(&u->state->port))
+		if (uart_cts_enabled(u))
 			ctrl |= AUART_CTRL2_RTSEN;
 		else
 			ctrl |= AUART_CTRL2_RTS;
diff --git a/drivers/tty/serial/nwpserial.c b/drivers/tty/serial/nwpserial.c
index c06366b..5da7622 100644
--- a/drivers/tty/serial/nwpserial.c
+++ b/drivers/tty/serial/nwpserial.c
@@ -22,6 +22,7 @@
 #include <linux/of_platform.h>
 #include <linux/of_device.h>
 #include <linux/nwpserial.h>
+#include <linux/delay.h>
 #include <asm/prom.h>
 #include <asm/dcr.h>
 
diff --git a/drivers/tty/serial/of_serial.c b/drivers/tty/serial/of_serial.c
index 68d4455..8bc2563 100644
--- a/drivers/tty/serial/of_serial.c
+++ b/drivers/tty/serial/of_serial.c
@@ -183,10 +183,6 @@
 					  "auto-flow-control"))
 			port8250.capabilities |= UART_CAP_AFE;
 
-		if (of_property_read_bool(ofdev->dev.of_node,
-					  "has-hw-flow-control"))
-			port8250.port.flags |= UPF_HARD_FLOW;
-
 		ret = serial8250_register_8250_port(&port8250);
 		break;
 	}
@@ -244,6 +240,32 @@
 	return 0;
 }
 
+#ifdef CONFIG_PM_SLEEP
+static int of_serial_suspend(struct device *dev)
+{
+	struct of_serial_info *info = dev_get_drvdata(dev);
+
+	serial8250_suspend_port(info->line);
+	if (info->clk)
+		clk_disable_unprepare(info->clk);
+
+	return 0;
+}
+
+static int of_serial_resume(struct device *dev)
+{
+	struct of_serial_info *info = dev_get_drvdata(dev);
+
+	if (info->clk)
+		clk_prepare_enable(info->clk);
+
+	serial8250_resume_port(info->line);
+
+	return 0;
+}
+#endif
+static SIMPLE_DEV_PM_OPS(of_serial_pm_ops, of_serial_suspend, of_serial_resume);
+
 /*
  * A few common types, add more as needed.
  */
@@ -275,6 +297,7 @@
 		.name = "of_serial",
 		.owner = THIS_MODULE,
 		.of_match_table = of_platform_serial_table,
+		.pm = &of_serial_pm_ops,
 	},
 	.probe = of_platform_serial_probe,
 	.remove = of_platform_serial_remove,
diff --git a/drivers/tty/serial/omap-serial.c b/drivers/tty/serial/omap-serial.c
index d017cec..18c30ca 100644
--- a/drivers/tty/serial/omap-serial.c
+++ b/drivers/tty/serial/omap-serial.c
@@ -239,6 +239,26 @@
 }
 
 /*
+ * Calculate the absolute difference between the desired and actual baud
+ * rate for the given mode.
+ */
+static inline int calculate_baud_abs_diff(struct uart_port *port,
+				unsigned int baud, unsigned int mode)
+{
+	unsigned int n = port->uartclk / (mode * baud);
+	int abs_diff;
+
+	if (n == 0)
+		n = 1;
+
+	abs_diff = baud - (port->uartclk / (mode * n));
+	if (abs_diff < 0)
+		abs_diff = -abs_diff;
+
+	return abs_diff;
+}
+
+/*
  * serial_omap_baud_is_mode16 - check if baud rate is MODE16X
  * @port: uart port info
  * @baud: baudrate for which mode needs to be determined
@@ -252,16 +272,10 @@
 static bool
 serial_omap_baud_is_mode16(struct uart_port *port, unsigned int baud)
 {
-	unsigned int n13 = port->uartclk / (13 * baud);
-	unsigned int n16 = port->uartclk / (16 * baud);
-	int baudAbsDiff13 = baud - (port->uartclk / (13 * n13));
-	int baudAbsDiff16 = baud - (port->uartclk / (16 * n16));
-	if (baudAbsDiff13 < 0)
-		baudAbsDiff13 = -baudAbsDiff13;
-	if (baudAbsDiff16 < 0)
-		baudAbsDiff16 = -baudAbsDiff16;
+	int abs_diff_13 = calculate_baud_abs_diff(port, baud, 13);
+	int abs_diff_16 = calculate_baud_abs_diff(port, baud, 16);
 
-	return (baudAbsDiff13 >= baudAbsDiff16);
+	return (abs_diff_13 >= abs_diff_16);
 }
 
 /*
diff --git a/drivers/tty/serial/serial_core.c b/drivers/tty/serial/serial_core.c
index 29a7be4..df3a8c7 100644
--- a/drivers/tty/serial/serial_core.c
+++ b/drivers/tty/serial/serial_core.c
@@ -59,6 +59,11 @@
 
 static void uart_port_shutdown(struct tty_port *port);
 
+static int uart_dcd_enabled(struct uart_port *uport)
+{
+	return uport->status & UPSTAT_DCD_ENABLE;
+}
+
 /*
  * This routine is used by the interrupt handler to schedule processing in
  * the software interrupt portion of the driver.
@@ -90,7 +95,7 @@
 	struct uart_state *state = tty->driver_data;
 	struct uart_port *port = state->uart_port;
 
-	if (!tty->stopped && !tty->hw_stopped)
+	if (!uart_tx_stopped(port))
 		port->ops->start_tx(port);
 }
 
@@ -130,7 +135,6 @@
 		int init_hw)
 {
 	struct uart_port *uport = state->uart_port;
-	struct tty_port *port = &state->port;
 	unsigned long page;
 	int retval = 0;
 
@@ -175,17 +179,14 @@
 			if (tty->termios.c_cflag & CBAUD)
 				uart_set_mctrl(uport, TIOCM_RTS | TIOCM_DTR);
 		}
-		/*
-		 * if hw support flow control without software intervention,
-		 * then skip the below check
-		 */
-		if (tty_port_cts_enabled(port) &&
-		    !(uport->flags & UPF_HARD_FLOW)) {
-			spin_lock_irq(&uport->lock);
-			if (!(uport->ops->get_mctrl(uport) & TIOCM_CTS))
-				tty->hw_stopped = 1;
-			spin_unlock_irq(&uport->lock);
-		}
+
+		spin_lock_irq(&uport->lock);
+		if (uart_cts_enabled(uport) &&
+		    !(uport->ops->get_mctrl(uport) & TIOCM_CTS))
+			uport->hw_stopped = 1;
+		else
+			uport->hw_stopped = 0;
+		spin_unlock_irq(&uport->lock);
 	}
 
 	/*
@@ -439,7 +440,6 @@
 static void uart_change_speed(struct tty_struct *tty, struct uart_state *state,
 					struct ktermios *old_termios)
 {
-	struct tty_port *port = &state->port;
 	struct uart_port *uport = state->uart_port;
 	struct ktermios *termios;
 
@@ -454,17 +454,19 @@
 	uport->ops->set_termios(uport, termios, old_termios);
 
 	/*
-	 * Set flags based on termios cflag
+	 * Set modem status enables based on termios cflag
 	 */
+	spin_lock_irq(&uport->lock);
 	if (termios->c_cflag & CRTSCTS)
-		set_bit(ASYNCB_CTS_FLOW, &port->flags);
+		uport->status |= UPSTAT_CTS_ENABLE;
 	else
-		clear_bit(ASYNCB_CTS_FLOW, &port->flags);
+		uport->status &= ~UPSTAT_CTS_ENABLE;
 
 	if (termios->c_cflag & CLOCAL)
-		clear_bit(ASYNCB_CHECK_CD, &port->flags);
+		uport->status &= ~UPSTAT_DCD_ENABLE;
 	else
-		set_bit(ASYNCB_CHECK_CD, &port->flags);
+		uport->status |= UPSTAT_DCD_ENABLE;
+	spin_unlock_irq(&uport->lock);
 }
 
 static inline int __uart_put_char(struct uart_port *port,
@@ -604,12 +606,11 @@
 	if (port->ops->send_xchar)
 		port->ops->send_xchar(port, ch);
 	else {
+		spin_lock_irqsave(&port->lock, flags);
 		port->x_char = ch;
-		if (ch) {
-			spin_lock_irqsave(&port->lock, flags);
+		if (ch)
 			port->ops->start_tx(port);
-			spin_unlock_irqrestore(&port->lock, flags);
-		}
+		spin_unlock_irqrestore(&port->lock, flags);
 	}
 }
 
@@ -652,12 +653,8 @@
 		mask &= ~port->flags;
 	}
 
-	if (mask & UPF_SOFT_FLOW) {
-		if (port->x_char)
-			port->x_char = 0;
-		else
-			uart_send_xchar(tty, START_CHAR(tty));
-	}
+	if (mask & UPF_SOFT_FLOW)
+		uart_send_xchar(tty, START_CHAR(tty));
 
 	if (mask & UPF_HARD_FLOW)
 		uart_set_mctrl(port, TIOCM_RTS);
@@ -892,10 +889,11 @@
 			 */
 			if (uport->flags & UPF_SPD_MASK) {
 				char buf[64];
-				printk(KERN_NOTICE
-				       "%s sets custom speed on %s. This "
-				       "is deprecated.\n", current->comm,
-				       tty_name(port->tty, buf));
+
+				dev_notice(uport->dev,
+				       "%s sets custom speed on %s. This is deprecated.\n",
+				      current->comm,
+				      tty_name(port->tty, buf));
 			}
 			uart_change_speed(tty, state, NULL);
 		}
@@ -952,7 +950,7 @@
 	 */
 	if (uport->x_char ||
 	    ((uart_circ_chars_pending(&state->xmit) > 0) &&
-	     !tty->stopped && !tty->hw_stopped))
+	     !uart_tx_stopped(uport)))
 		result &= ~TIOCSER_TEMT;
 
 	return put_user(result, value);
@@ -1251,7 +1249,6 @@
 {
 	struct uart_state *state = tty->driver_data;
 	struct uart_port *uport = state->uart_port;
-	unsigned long flags;
 	unsigned int cflag = tty->termios.c_cflag;
 	unsigned int iflag_mask = IGNBRK|BRKINT|IGNPAR|PARMRK|INPCK;
 	bool sw_changed = false;
@@ -1291,34 +1288,33 @@
 	/* Handle transition away from B0 status */
 	else if (!(old_termios->c_cflag & CBAUD) && (cflag & CBAUD)) {
 		unsigned int mask = TIOCM_DTR;
-		if (!(cflag & CRTSCTS) ||
-		    !test_bit(TTY_THROTTLED, &tty->flags))
+		if (!(cflag & CRTSCTS) || !test_bit(TTY_THROTTLED, &tty->flags))
 			mask |= TIOCM_RTS;
 		uart_set_mctrl(uport, mask);
 	}
 
 	/*
 	 * If the port is doing h/w assisted flow control, do nothing.
-	 * We assume that tty->hw_stopped has never been set.
+	 * We assume that port->hw_stopped has never been set.
 	 */
 	if (uport->flags & UPF_HARD_FLOW)
 		return;
 
 	/* Handle turning off CRTSCTS */
 	if ((old_termios->c_cflag & CRTSCTS) && !(cflag & CRTSCTS)) {
-		spin_lock_irqsave(&uport->lock, flags);
-		tty->hw_stopped = 0;
+		spin_lock_irq(&uport->lock);
+		uport->hw_stopped = 0;
 		__uart_start(tty);
-		spin_unlock_irqrestore(&uport->lock, flags);
+		spin_unlock_irq(&uport->lock);
 	}
 	/* Handle turning on CRTSCTS */
 	else if (!(old_termios->c_cflag & CRTSCTS) && (cflag & CRTSCTS)) {
-		spin_lock_irqsave(&uport->lock, flags);
+		spin_lock_irq(&uport->lock);
 		if (!(uport->ops->get_mctrl(uport) & TIOCM_CTS)) {
-			tty->hw_stopped = 1;
+			uport->hw_stopped = 1;
 			uport->ops->stop_tx(uport);
 		}
-		spin_unlock_irqrestore(&uport->lock, flags);
+		spin_unlock_irq(&uport->lock);
 	}
 }
 
@@ -1975,12 +1971,9 @@
 		for (tries = 3; !ops->tx_empty(uport) && tries; tries--)
 			msleep(10);
 		if (!tries)
-			printk(KERN_ERR "%s%s%s%d: Unable to drain "
-					"transmitter\n",
-			       uport->dev ? dev_name(uport->dev) : "",
-			       uport->dev ? ": " : "",
-			       drv->dev_name,
-			       drv->tty_driver->name_base + uport->line);
+			dev_err(uport->dev, "%s%d: Unable to drain transmitter\n",
+				drv->dev_name,
+				drv->tty_driver->name_base + uport->line);
 
 		if (console_suspend_enabled || !uart_console(uport))
 			ops->shutdown(uport);
@@ -2109,9 +2102,7 @@
 		break;
 	}
 
-	printk(KERN_INFO "%s%s%s%d at %s (irq = %d, base_baud = %d) is a %s\n",
-	       port->dev ? dev_name(port->dev) : "",
-	       port->dev ? ": " : "",
+	dev_info(port->dev, "%s%d at %s (irq = %d, base_baud = %d) is a %s\n",
 	       drv->dev_name,
 	       drv->tty_driver->name_base + port->line,
 	       address, port->irq, port->uartclk / 16, uart_type(port));
@@ -2640,7 +2631,7 @@
 	if (likely(!IS_ERR(tty_dev))) {
 		device_set_wakeup_capable(tty_dev, 1);
 	} else {
-		printk(KERN_ERR "Cannot register tty device on line %d\n",
+		dev_err(uport->dev, "Cannot register tty device on line %d\n",
 		       uport->line);
 	}
 
@@ -2675,7 +2666,7 @@
 	BUG_ON(in_interrupt());
 
 	if (state->uart_port != uport)
-		printk(KERN_ALERT "Removing wrong port: %p != %p\n",
+		dev_alert(uport->dev, "Removing wrong port: %p != %p\n",
 			state->uart_port, uport);
 
 	mutex_lock(&port_mutex);
@@ -2757,22 +2748,29 @@
  *	uart_handle_dcd_change - handle a change of carrier detect state
  *	@uport: uart_port structure for the open port
  *	@status: new carrier detect status, nonzero if active
+ *
+ *	Caller must hold uport->lock
  */
 void uart_handle_dcd_change(struct uart_port *uport, unsigned int status)
 {
 	struct tty_port *port = &uport->state->port;
 	struct tty_struct *tty = port->tty;
-	struct tty_ldisc *ld = tty ? tty_ldisc_ref(tty) : NULL;
+	struct tty_ldisc *ld;
 
-	if (ld) {
-		if (ld->ops->dcd_change)
-			ld->ops->dcd_change(tty, status);
-		tty_ldisc_deref(ld);
+	lockdep_assert_held_once(&uport->lock);
+
+	if (tty) {
+		ld = tty_ldisc_ref(tty);
+		if (ld) {
+			if (ld->ops->dcd_change)
+				ld->ops->dcd_change(tty, status);
+			tty_ldisc_deref(ld);
+		}
 	}
 
 	uport->icount.dcd++;
 
-	if (port->flags & ASYNC_CHECK_CD) {
+	if (uart_dcd_enabled(uport)) {
 		if (status)
 			wake_up_interruptible(&port->open_wait);
 		else if (tty)
@@ -2785,26 +2783,25 @@
  *	uart_handle_cts_change - handle a change of clear-to-send state
  *	@uport: uart_port structure for the open port
  *	@status: new clear to send status, nonzero if active
+ *
+ *	Caller must hold uport->lock
  */
 void uart_handle_cts_change(struct uart_port *uport, unsigned int status)
 {
-	struct tty_port *port = &uport->state->port;
-	struct tty_struct *tty = port->tty;
+	lockdep_assert_held_once(&uport->lock);
 
 	uport->icount.cts++;
 
-	/* skip below code if the hw flow control is supported */
-	if (tty_port_cts_enabled(port) &&
-	    !(uport->flags & UPF_HARD_FLOW)) {
-		if (tty->hw_stopped) {
+	if (uart_cts_enabled(uport)) {
+		if (uport->hw_stopped) {
 			if (status) {
-				tty->hw_stopped = 0;
+				uport->hw_stopped = 0;
 				uport->ops->start_tx(uport);
 				uart_write_wakeup(uport);
 			}
 		} else {
 			if (!status) {
-				tty->hw_stopped = 1;
+				uport->hw_stopped = 1;
 				uport->ops->stop_tx(uport);
 			}
 		}
diff --git a/drivers/tty/serial/serial_mctrl_gpio.c b/drivers/tty/serial/serial_mctrl_gpio.c
index bf9560f..a3035f9 100644
--- a/drivers/tty/serial/serial_mctrl_gpio.c
+++ b/drivers/tty/serial/serial_mctrl_gpio.c
@@ -18,7 +18,7 @@
 #include <linux/err.h>
 #include <linux/device.h>
 #include <linux/gpio/consumer.h>
-#include <uapi/asm-generic/termios.h>
+#include <linux/termios.h>
 
 #include "serial_mctrl_gpio.h"
 
diff --git a/drivers/tty/serial/st-asc.c b/drivers/tty/serial/st-asc.c
index 8b2d735..a316584 100644
--- a/drivers/tty/serial/st-asc.c
+++ b/drivers/tty/serial/st-asc.c
@@ -151,12 +151,20 @@
 
 static inline u32 asc_in(struct uart_port *port, u32 offset)
 {
+#ifdef readl_relaxed
+	return readl_relaxed(port->membase + offset);
+#else
 	return readl(port->membase + offset);
+#endif
 }
 
 static inline void asc_out(struct uart_port *port, u32 offset, u32 value)
 {
+#ifdef writel_relaxed
+	writel_relaxed(value, port->membase + offset);
+#else
 	writel(value, port->membase + offset);
+#endif
 }
 
 /*
diff --git a/drivers/tty/serial/sunhv.c b/drivers/tty/serial/sunhv.c
index 20521db..25d43ce 100644
--- a/drivers/tty/serial/sunhv.c
+++ b/drivers/tty/serial/sunhv.c
@@ -268,6 +268,9 @@
 	unsigned long flags;
 	int limit = 10000;
 
+	if (ch == __DISABLED_CHAR)
+		return;
+
 	spin_lock_irqsave(&port->lock, flags);
 
 	while (limit-- > 0) {
diff --git a/drivers/tty/serial/sunsab.c b/drivers/tty/serial/sunsab.c
index b9598b2..b339fe4 100644
--- a/drivers/tty/serial/sunsab.c
+++ b/drivers/tty/serial/sunsab.c
@@ -436,7 +436,7 @@
 	struct circ_buf *xmit = &up->port.state->xmit;
 	int i;
 
-	if (uart_circ_empty(xmit))
+	if (uart_circ_empty(xmit) || uart_tx_stopped(port))
 		return;
 
 	up->interrupt_mask1 &= ~(SAB82532_IMR1_ALLS|SAB82532_IMR1_XPR);
@@ -468,6 +468,9 @@
 	struct uart_sunsab_port *up = (struct uart_sunsab_port *) port;
 	unsigned long flags;
 
+	if (ch == __DISABLED_CHAR)
+		return;
+
 	spin_lock_irqsave(&up->port.lock, flags);
 
 	sunsab_tec_wait(up);
diff --git a/drivers/tty/serial/uartlite.c b/drivers/tty/serial/uartlite.c
index 9fc22f4..189f52e 100644
--- a/drivers/tty/serial/uartlite.c
+++ b/drivers/tty/serial/uartlite.c
@@ -665,7 +665,6 @@
 	.probe = ulite_probe,
 	.remove = ulite_remove,
 	.driver = {
-		.owner = THIS_MODULE,
 		.name  = "uartlite",
 		.of_match_table = of_match_ptr(ulite_of_match),
 	},
diff --git a/drivers/tty/serial/vr41xx_siu.c b/drivers/tty/serial/vr41xx_siu.c
index db0c8a4..d7f9d62 100644
--- a/drivers/tty/serial/vr41xx_siu.c
+++ b/drivers/tty/serial/vr41xx_siu.c
@@ -847,7 +847,6 @@
 	siu_uart_ports[port->line].type = port->type;
 	siu_uart_ports[port->line].uartclk = SIU_BAUD_BASE * 16;
 	siu_uart_ports[port->line].mapbase = port->mapbase;
-	siu_uart_ports[port->line].mapbase = port->mapbase;
 	siu_uart_ports[port->line].ops = &siu_uart_ops;
 }
 
diff --git a/drivers/tty/serial/vt8500_serial.c b/drivers/tty/serial/vt8500_serial.c
index 15ad6fc..b2bc9e8 100644
--- a/drivers/tty/serial/vt8500_serial.c
+++ b/drivers/tty/serial/vt8500_serial.c
@@ -33,8 +33,8 @@
 #include <linux/serial.h>
 #include <linux/slab.h>
 #include <linux/clk.h>
-#include <linux/platform_device.h>
 #include <linux/of.h>
+#include <linux/of_device.h>
 #include <linux/err.h>
 
 /*
@@ -78,13 +78,40 @@
 #define RX_FIFO_INTS	(RXFAF | RXFF | RXOVER | PER | FER | RXTOUT)
 #define TX_FIFO_INTS	(TXFAE | TXFE | TXUDR)
 
+/*
+ * Line control bits
+ */
+
+#define VT8500_TXEN	(1 << 0)	/* Enable transmit logic */
+#define VT8500_RXEN	(1 << 1)	/* Enable receive logic */
+#define VT8500_CS8	(1 << 2)	/* 8-bit data length (vs. 7-bit) */
+#define VT8500_CSTOPB	(1 << 3)	/* 2 stop bits (vs. 1) */
+#define VT8500_PARENB	(1 << 4)	/* Enable parity */
+#define VT8500_PARODD	(1 << 5)	/* Odd parity (vs. even) */
+#define VT8500_RTS	(1 << 6)	/* Ready to send */
+#define VT8500_LOOPBK	(1 << 7)	/* Enable internal loopback */
+#define VT8500_DMA	(1 << 8)	/* Enable DMA mode (needs FIFO) */
+#define VT8500_BREAK	(1 << 9)	/* Initiate break signal */
+#define VT8500_PSLVERR	(1 << 10)	/* APB error upon empty RX FIFO read */
+#define VT8500_SWRTSCTS	(1 << 11)	/* Software-controlled RTS/CTS */
+
+/*
+ * Capability flags (driver-internal)
+ */
+
+#define VT8500_HAS_SWRTSCTS_SWITCH	(1 << 1)
+
+#define VT8500_RECOMMENDED_CLK		12000000
+#define VT8500_OVERSAMPLING_DIVISOR	13
 #define VT8500_MAX_PORTS	6
 
 struct vt8500_port {
 	struct uart_port	uart;
 	char			name[16];
 	struct clk		*clk;
+	unsigned int		clk_predivisor;
 	unsigned int		ier;
+	unsigned int		vt8500_uart_flags;
 };
 
 /*
@@ -267,31 +294,45 @@
 
 static void vt8500_set_mctrl(struct uart_port *port, unsigned int mctrl)
 {
+	unsigned int lcr = vt8500_read(port, VT8500_URLCR);
+
+	if (mctrl & TIOCM_RTS)
+		lcr |= VT8500_RTS;
+	else
+		lcr &= ~VT8500_RTS;
+
+	vt8500_write(port, lcr, VT8500_URLCR);
 }
 
 static void vt8500_break_ctl(struct uart_port *port, int break_ctl)
 {
 	if (break_ctl)
-		vt8500_write(port, vt8500_read(port, VT8500_URLCR) | (1 << 9),
+		vt8500_write(port,
+			     vt8500_read(port, VT8500_URLCR) | VT8500_BREAK,
 			     VT8500_URLCR);
 }
 
 static int vt8500_set_baud_rate(struct uart_port *port, unsigned int baud)
 {
+	struct vt8500_port *vt8500_port =
+			container_of(port, struct vt8500_port, uart);
 	unsigned long div;
 	unsigned int loops = 1000;
 
-	div = vt8500_read(port, VT8500_URDIV) & ~(0x3ff);
+	div = ((vt8500_port->clk_predivisor - 1) & 0xf) << 16;
+	div |= (uart_get_divisor(port, baud) - 1) & 0x3ff;
 
-	if (unlikely((baud < 900) || (baud > 921600)))
-		div |= 7;
-	else
-		div |= (921600 / baud) - 1;
+	/* Effective baud rate */
+	baud = port->uartclk / 16 / ((div & 0x3ff) + 1);
 
 	while ((vt8500_read(port, VT8500_URUSR) & (1 << 5)) && --loops)
 		cpu_relax();
+
 	vt8500_write(port, div, VT8500_URDIV);
 
+	/* Break signal timing depends on baud rate, update accordingly */
+	vt8500_write(port, mult_frac(baud, 4096, 1000000), VT8500_URBKR);
+
 	return baud;
 }
 
@@ -347,31 +388,35 @@
 
 	/* calculate parity */
 	lcr = vt8500_read(&vt8500_port->uart, VT8500_URLCR);
-	lcr &= ~((1 << 5) | (1 << 4));
+	lcr &= ~(VT8500_PARENB | VT8500_PARODD);
 	if (termios->c_cflag & PARENB) {
-		lcr |= (1 << 4);
+		lcr |= VT8500_PARENB;
 		termios->c_cflag &= ~CMSPAR;
 		if (termios->c_cflag & PARODD)
-			lcr |= (1 << 5);
+			lcr |= VT8500_PARODD;
 	}
 
 	/* calculate bits per char */
-	lcr &= ~(1 << 2);
+	lcr &= ~VT8500_CS8;
 	switch (termios->c_cflag & CSIZE) {
 	case CS7:
 		break;
 	case CS8:
 	default:
-		lcr |= (1 << 2);
+		lcr |= VT8500_CS8;
 		termios->c_cflag &= ~CSIZE;
 		termios->c_cflag |= CS8;
 		break;
 	}
 
 	/* calculate stop bits */
-	lcr &= ~(1 << 3);
+	lcr &= ~VT8500_CSTOPB;
 	if (termios->c_cflag & CSTOPB)
-		lcr |= (1 << 3);
+		lcr |= VT8500_CSTOPB;
+
+	lcr &= ~VT8500_SWRTSCTS;
+	if (vt8500_port->vt8500_uart_flags & VT8500_HAS_SWRTSCTS_SWITCH)
+		lcr |= VT8500_SWRTSCTS;
 
 	/* set parity, bits per char, and stop bit */
 	vt8500_write(&vt8500_port->uart, lcr, VT8500_URLCR);
@@ -521,6 +566,33 @@
 #define VT8500_CONSOLE	NULL
 #endif
 
+#ifdef CONFIG_CONSOLE_POLL
+static int vt8500_get_poll_char(struct uart_port *port)
+{
+	unsigned int status = vt8500_read(port, VT8500_URFIDX);
+
+	if (!(status & 0x1f00))
+		return NO_POLL_CHAR;
+
+	return vt8500_read(port, VT8500_RXFIFO) & 0xff;
+}
+
+static void vt8500_put_poll_char(struct uart_port *port, unsigned char c)
+{
+	unsigned int status, tmout = 10000;
+
+	do {
+		status = vt8500_read(port, VT8500_URFIDX);
+
+		if (--tmout == 0)
+			break;
+		udelay(1);
+	} while (status & 0x10);
+
+	vt8500_write(port, c, VT8500_TXFIFO);
+}
+#endif
+
 static struct uart_ops vt8500_uart_pops = {
 	.tx_empty	= vt8500_tx_empty,
 	.set_mctrl	= vt8500_set_mctrl,
@@ -538,6 +610,10 @@
 	.request_port	= vt8500_request_port,
 	.config_port	= vt8500_config_port,
 	.verify_port	= vt8500_verify_port,
+#ifdef CONFIG_CONSOLE_POLL
+	.poll_get_char	= vt8500_get_poll_char,
+	.poll_put_char	= vt8500_put_poll_char,
+#endif
 };
 
 static struct uart_driver vt8500_uart_driver = {
@@ -548,14 +624,31 @@
 	.cons		= VT8500_CONSOLE,
 };
 
+static unsigned int vt8500_flags; /* none required so far */
+static unsigned int wm8880_flags = VT8500_HAS_SWRTSCTS_SWITCH;
+
+static const struct of_device_id wmt_dt_ids[] = {
+	{ .compatible = "via,vt8500-uart", .data = &vt8500_flags},
+	{ .compatible = "wm,wm8880-uart", .data = &wm8880_flags},
+	{}
+};
+
 static int vt8500_serial_probe(struct platform_device *pdev)
 {
 	struct vt8500_port *vt8500_port;
 	struct resource *mmres, *irqres;
 	struct device_node *np = pdev->dev.of_node;
+	const struct of_device_id *match;
+	const unsigned int *flags;
 	int ret;
 	int port;
 
+	match = of_match_device(wmt_dt_ids, &pdev->dev);
+	if (!match)
+		return -EINVAL;
+
+	flags = match->data;
+
 	mmres = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	irqres = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
 	if (!mmres || !irqres)
@@ -605,6 +698,11 @@
 		return ret;
 	}
 
+	vt8500_port->vt8500_uart_flags = *flags;
+	vt8500_port->clk_predivisor = DIV_ROUND_CLOSEST(
+					clk_get_rate(vt8500_port->clk),
+					VT8500_RECOMMENDED_CLK
+				      );
 	vt8500_port->uart.type = PORT_VT8500;
 	vt8500_port->uart.iotype = UPIO_MEM;
 	vt8500_port->uart.mapbase = mmres->start;
@@ -615,7 +713,10 @@
 	vt8500_port->uart.dev = &pdev->dev;
 	vt8500_port->uart.flags = UPF_IOREMAP | UPF_BOOT_AUTOCONF;
 
-	vt8500_port->uart.uartclk = clk_get_rate(vt8500_port->clk);
+	/* Serial core uses the magic "16" everywhere - adjust for it */
+	vt8500_port->uart.uartclk = 16 * clk_get_rate(vt8500_port->clk) /
+					vt8500_port->clk_predivisor /
+					VT8500_OVERSAMPLING_DIVISOR;
 
 	snprintf(vt8500_port->name, sizeof(vt8500_port->name),
 		 "VT8500 UART%d", pdev->id);
@@ -639,11 +740,6 @@
 	return 0;
 }
 
-static const struct of_device_id wmt_dt_ids[] = {
-	{ .compatible = "via,vt8500-uart", },
-	{}
-};
-
 static struct platform_driver vt8500_platform_driver = {
 	.probe  = vt8500_serial_probe,
 	.remove = vt8500_serial_remove,
diff --git a/drivers/tty/serial/xilinx_uartps.c b/drivers/tty/serial/xilinx_uartps.c
index 806e4bc..200c1af 100644
--- a/drivers/tty/serial/xilinx_uartps.c
+++ b/drivers/tty/serial/xilinx_uartps.c
@@ -1051,6 +1051,25 @@
 	cdns_uart_writel(ch, CDNS_UART_FIFO_OFFSET);
 }
 
+static void cdns_early_write(struct console *con, const char *s, unsigned n)
+{
+	struct earlycon_device *dev = con->data;
+
+	uart_console_write(&dev->port, s, n, cdns_uart_console_putchar);
+}
+
+static int __init cdns_early_console_setup(struct earlycon_device *device,
+					   const char *opt)
+{
+	if (!device->port.membase)
+		return -ENODEV;
+
+	device->con->write = cdns_early_write;
+
+	return 0;
+}
+EARLYCON_DECLARE(cdns, cdns_early_console_setup);
+
 /**
  * cdns_uart_console_write - perform write operation
  * @co: Console handle
@@ -1428,7 +1447,6 @@
 	.probe   = cdns_uart_probe,
 	.remove  = cdns_uart_remove,
 	.driver  = {
-		.owner = THIS_MODULE,
 		.name = CDNS_UART_NAME,
 		.of_match_table = cdns_uart_of_match,
 		.pm = &cdns_uart_dev_pm_ops,
diff --git a/drivers/tty/tty_io.c b/drivers/tty/tty_io.c
index 8fbad34..2f6f9b5 100644
--- a/drivers/tty/tty_io.c
+++ b/drivers/tty/tty_io.c
@@ -908,8 +908,7 @@
  *	stop_tty	-	propagate flow control
  *	@tty: tty to stop
  *
- *	Perform flow control to the driver. For PTY/TTY pairs we
- *	must also propagate the TIOCKPKT status. May be called
+ *	Perform flow control to the driver. May be called
  *	on an already stopped device and will not re-call the driver
  *	method.
  *
@@ -919,64 +918,58 @@
  *	but not always.
  *
  *	Locking:
- *		Uses the tty control lock internally
+ *		flow_lock
  */
 
-void stop_tty(struct tty_struct *tty)
+void __stop_tty(struct tty_struct *tty)
 {
-	unsigned long flags;
-	spin_lock_irqsave(&tty->ctrl_lock, flags);
-	if (tty->stopped) {
-		spin_unlock_irqrestore(&tty->ctrl_lock, flags);
+	if (tty->stopped)
 		return;
-	}
 	tty->stopped = 1;
-	if (tty->link && tty->link->packet) {
-		tty->ctrl_status &= ~TIOCPKT_START;
-		tty->ctrl_status |= TIOCPKT_STOP;
-		wake_up_interruptible_poll(&tty->link->read_wait, POLLIN);
-	}
-	spin_unlock_irqrestore(&tty->ctrl_lock, flags);
 	if (tty->ops->stop)
 		(tty->ops->stop)(tty);
 }
 
+void stop_tty(struct tty_struct *tty)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&tty->flow_lock, flags);
+	__stop_tty(tty);
+	spin_unlock_irqrestore(&tty->flow_lock, flags);
+}
 EXPORT_SYMBOL(stop_tty);
 
 /**
  *	start_tty	-	propagate flow control
  *	@tty: tty to start
  *
- *	Start a tty that has been stopped if at all possible. Perform
- *	any necessary wakeups and propagate the TIOCPKT status. If this
- *	is the tty was previous stopped and is being started then the
- *	driver start method is invoked and the line discipline woken.
+ *	Start a tty that has been stopped if at all possible. If this
+ *	tty was previous stopped and is now being started, the driver
+ *	start method is invoked and the line discipline woken.
  *
  *	Locking:
- *		ctrl_lock
+ *		flow_lock
  */
 
+void __start_tty(struct tty_struct *tty)
+{
+	if (!tty->stopped || tty->flow_stopped)
+		return;
+	tty->stopped = 0;
+	if (tty->ops->start)
+		(tty->ops->start)(tty);
+	tty_wakeup(tty);
+}
+
 void start_tty(struct tty_struct *tty)
 {
 	unsigned long flags;
-	spin_lock_irqsave(&tty->ctrl_lock, flags);
-	if (!tty->stopped || tty->flow_stopped) {
-		spin_unlock_irqrestore(&tty->ctrl_lock, flags);
-		return;
-	}
-	tty->stopped = 0;
-	if (tty->link && tty->link->packet) {
-		tty->ctrl_status &= ~TIOCPKT_STOP;
-		tty->ctrl_status |= TIOCPKT_START;
-		wake_up_interruptible_poll(&tty->link->read_wait, POLLIN);
-	}
-	spin_unlock_irqrestore(&tty->ctrl_lock, flags);
-	if (tty->ops->start)
-		(tty->ops->start)(tty);
-	/* If we have a running line discipline it may need kicking */
-	tty_wakeup(tty);
-}
 
+	spin_lock_irqsave(&tty->flow_lock, flags);
+	__start_tty(tty);
+	spin_unlock_irqrestore(&tty->flow_lock, flags);
+}
 EXPORT_SYMBOL(start_tty);
 
 /* We limit tty time update visibility to every 8 seconds or so. */
@@ -1030,14 +1023,14 @@
 	return i;
 }
 
-void tty_write_unlock(struct tty_struct *tty)
+static void tty_write_unlock(struct tty_struct *tty)
 	__releases(&tty->atomic_write_lock)
 {
 	mutex_unlock(&tty->atomic_write_lock);
 	wake_up_interruptible_poll(&tty->write_wait, POLLOUT);
 }
 
-int tty_write_lock(struct tty_struct *tty, int ndelay)
+static int tty_write_lock(struct tty_struct *tty, int ndelay)
 	__acquires(&tty->atomic_write_lock)
 {
 	if (!mutex_trylock(&tty->atomic_write_lock)) {
@@ -1224,6 +1217,35 @@
 	return tty_write(file, buf, count, ppos);
 }
 
+/**
+ *	tty_send_xchar	-	send priority character
+ *
+ *	Send a high priority character to the tty even if stopped
+ *
+ *	Locking: none for xchar method, write ordering for write method.
+ */
+
+int tty_send_xchar(struct tty_struct *tty, char ch)
+{
+	int	was_stopped = tty->stopped;
+
+	if (tty->ops->send_xchar) {
+		tty->ops->send_xchar(tty, ch);
+		return 0;
+	}
+
+	if (tty_write_lock(tty, 0) < 0)
+		return -ERESTARTSYS;
+
+	if (was_stopped)
+		start_tty(tty);
+	tty->ops->write(tty, &ch, 1);
+	if (was_stopped)
+		stop_tty(tty);
+	tty_write_unlock(tty);
+	return 0;
+}
+
 static char ptychar[] = "pqrstuvwxyzabcde";
 
 /**
@@ -1544,13 +1566,14 @@
 	struct tty_struct *tty =
 		container_of(work, struct tty_struct, hangup_work);
 	struct tty_driver *driver = tty->driver;
+	struct module *owner = driver->owner;
 
 	if (tty->ops->cleanup)
 		tty->ops->cleanup(tty);
 
 	tty->magic = 0;
 	tty_driver_kref_put(driver);
-	module_put(driver->owner);
+	module_put(owner);
 
 	spin_lock(&tty_files_lock);
 	list_del_init(&tty->tty_files);
@@ -3018,6 +3041,7 @@
 	INIT_WORK(&tty->hangup_work, do_tty_hangup);
 	mutex_init(&tty->atomic_write_lock);
 	spin_lock_init(&tty->ctrl_lock);
+	spin_lock_init(&tty->flow_lock);
 	INIT_LIST_HEAD(&tty->tty_files);
 	INIT_WORK(&tty->SAK_work, do_SAK_work);
 
diff --git a/drivers/tty/tty_ioctl.c b/drivers/tty/tty_ioctl.c
index 6fd60fe..62380cc 100644
--- a/drivers/tty/tty_ioctl.c
+++ b/drivers/tty/tty_ioctl.c
@@ -402,7 +402,7 @@
 
 #ifdef BOTHER
 	/* If the user asked for a precise weird speed give a precise weird
-	   answer. If they asked for a Bfoo speed they many have problems
+	   answer. If they asked for a Bfoo speed they may have problems
 	   digesting non-exact replies so fuzz a bit */
 
 	if ((termios->c_cflag & CBAUD) == BOTHER)
@@ -912,35 +912,6 @@
 #endif
 
 /**
- *	send_prio_char		-	send priority character
- *
- *	Send a high priority character to the tty even if stopped
- *
- *	Locking: none for xchar method, write ordering for write method.
- */
-
-static int send_prio_char(struct tty_struct *tty, char ch)
-{
-	int	was_stopped = tty->stopped;
-
-	if (tty->ops->send_xchar) {
-		tty->ops->send_xchar(tty, ch);
-		return 0;
-	}
-
-	if (tty_write_lock(tty, 0) < 0)
-		return -ERESTARTSYS;
-
-	if (was_stopped)
-		start_tty(tty);
-	tty->ops->write(tty, &ch, 1);
-	if (was_stopped)
-		stop_tty(tty);
-	tty_write_unlock(tty);
-	return 0;
-}
-
-/**
  *	tty_change_softcar	-	carrier change ioctl helper
  *	@tty: tty to update
  *	@arg: enable/disable CLOCAL
@@ -1177,29 +1148,37 @@
 			return retval;
 		switch (arg) {
 		case TCOOFF:
+			spin_lock_irq(&tty->flow_lock);
 			if (!tty->flow_stopped) {
 				tty->flow_stopped = 1;
-				stop_tty(tty);
+				__stop_tty(tty);
 			}
+			spin_unlock_irq(&tty->flow_lock);
 			break;
 		case TCOON:
+			spin_lock_irq(&tty->flow_lock);
 			if (tty->flow_stopped) {
 				tty->flow_stopped = 0;
-				start_tty(tty);
+				__start_tty(tty);
 			}
+			spin_unlock_irq(&tty->flow_lock);
 			break;
 		case TCIOFF:
+			down_read(&tty->termios_rwsem);
 			if (STOP_CHAR(tty) != __DISABLED_CHAR)
-				return send_prio_char(tty, STOP_CHAR(tty));
+				retval = tty_send_xchar(tty, STOP_CHAR(tty));
+			up_read(&tty->termios_rwsem);
 			break;
 		case TCION:
+			down_read(&tty->termios_rwsem);
 			if (START_CHAR(tty) != __DISABLED_CHAR)
-				return send_prio_char(tty, START_CHAR(tty));
+				retval = tty_send_xchar(tty, START_CHAR(tty));
+			up_read(&tty->termios_rwsem);
 			break;
 		default:
 			return -EINVAL;
 		}
-		return 0;
+		return retval;
 	case TCFLSH:
 		retval = tty_check_change(tty);
 		if (retval)
diff --git a/drivers/tty/vt/keyboard.c b/drivers/tty/vt/keyboard.c
index d0e3a44..c039cfe 100644
--- a/drivers/tty/vt/keyboard.c
+++ b/drivers/tty/vt/keyboard.c
@@ -268,30 +268,30 @@
 static int kbd_rate_helper(struct input_handle *handle, void *data)
 {
 	struct input_dev *dev = handle->dev;
-	struct kbd_repeat *rep = data;
+	struct kbd_repeat *rpt = data;
 
 	if (test_bit(EV_REP, dev->evbit)) {
 
-		if (rep[0].delay > 0)
+		if (rpt[0].delay > 0)
 			input_inject_event(handle,
-					   EV_REP, REP_DELAY, rep[0].delay);
-		if (rep[0].period > 0)
+					   EV_REP, REP_DELAY, rpt[0].delay);
+		if (rpt[0].period > 0)
 			input_inject_event(handle,
-					   EV_REP, REP_PERIOD, rep[0].period);
+					   EV_REP, REP_PERIOD, rpt[0].period);
 
-		rep[1].delay = dev->rep[REP_DELAY];
-		rep[1].period = dev->rep[REP_PERIOD];
+		rpt[1].delay = dev->rep[REP_DELAY];
+		rpt[1].period = dev->rep[REP_PERIOD];
 	}
 
 	return 0;
 }
 
-int kbd_rate(struct kbd_repeat *rep)
+int kbd_rate(struct kbd_repeat *rpt)
 {
-	struct kbd_repeat data[2] = { *rep };
+	struct kbd_repeat data[2] = { *rpt };
 
 	input_handler_for_each_handle(&kbd_handler, data, kbd_rate_helper);
-	*rep = data[1];	/* Copy currently used settings */
+	*rpt = data[1];	/* Copy currently used settings */
 
 	return 0;
 }
@@ -971,15 +971,15 @@
 	return ledstate;
 }
 
-void setledstate(struct kbd_struct *kbd, unsigned int led)
+void setledstate(struct kbd_struct *kb, unsigned int led)
 {
         unsigned long flags;
         spin_lock_irqsave(&led_lock, flags);
 	if (!(led & ~7)) {
 		ledioctl = led;
-		kbd->ledmode = LED_SHOW_IOCTL;
+		kb->ledmode = LED_SHOW_IOCTL;
 	} else
-		kbd->ledmode = LED_SHOW_FLAGS;
+		kb->ledmode = LED_SHOW_FLAGS;
 
 	set_leds();
 	spin_unlock_irqrestore(&led_lock, flags);
@@ -987,12 +987,12 @@
 
 static inline unsigned char getleds(void)
 {
-	struct kbd_struct *kbd = kbd_table + fg_console;
+	struct kbd_struct *kb = kbd_table + fg_console;
 
-	if (kbd->ledmode == LED_SHOW_IOCTL)
+	if (kb->ledmode == LED_SHOW_IOCTL)
 		return ledioctl;
 
-	return kbd->ledflagstate;
+	return kb->ledflagstate;
 }
 
 static int kbd_update_leds_helper(struct input_handle *handle, void *data)
@@ -1018,12 +1018,12 @@
  */
 int vt_get_leds(int console, int flag)
 {
-	struct kbd_struct * kbd = kbd_table + console;
+	struct kbd_struct *kb = kbd_table + console;
 	int ret;
 	unsigned long flags;
 
 	spin_lock_irqsave(&led_lock, flags);
-	ret = vc_kbd_led(kbd, flag);
+	ret = vc_kbd_led(kb, flag);
 	spin_unlock_irqrestore(&led_lock, flags);
 
 	return ret;
@@ -1040,8 +1040,8 @@
  */
 void vt_set_led_state(int console, int leds)
 {
-	struct kbd_struct * kbd = kbd_table + console;
-	setledstate(kbd, leds);
+	struct kbd_struct *kb = kbd_table + console;
+	setledstate(kb, leds);
 }
 
 /**
@@ -1059,10 +1059,10 @@
  */
 void vt_kbd_con_start(int console)
 {
-	struct kbd_struct * kbd = kbd_table + console;
+	struct kbd_struct *kb = kbd_table + console;
 	unsigned long flags;
 	spin_lock_irqsave(&led_lock, flags);
-	clr_vc_kbd_led(kbd, VC_SCROLLOCK);
+	clr_vc_kbd_led(kb, VC_SCROLLOCK);
 	set_leds();
 	spin_unlock_irqrestore(&led_lock, flags);
 }
@@ -1076,10 +1076,10 @@
  */
 void vt_kbd_con_stop(int console)
 {
-	struct kbd_struct * kbd = kbd_table + console;
+	struct kbd_struct *kb = kbd_table + console;
 	unsigned long flags;
 	spin_lock_irqsave(&led_lock, flags);
-	set_vc_kbd_led(kbd, VC_SCROLLOCK);
+	set_vc_kbd_led(kb, VC_SCROLLOCK);
 	set_leds();
 	spin_unlock_irqrestore(&led_lock, flags);
 }
@@ -1512,15 +1512,14 @@
 /**
  *	vt_do_diacrit		-	diacritical table updates
  *	@cmd: ioctl request
- *	@up: pointer to user data for ioctl
+ *	@udp: pointer to user data for ioctl
  *	@perm: permissions check computed by caller
  *
  *	Update the diacritical tables atomically and safely. Lock them
  *	against simultaneous keypresses
  */
-int vt_do_diacrit(unsigned int cmd, void __user *up, int perm)
+int vt_do_diacrit(unsigned int cmd, void __user *udp, int perm)
 {
-	struct kbdiacrs __user *a = up;
 	unsigned long flags;
 	int asize;
 	int ret = 0;
@@ -1528,12 +1527,13 @@
 	switch (cmd) {
 	case KDGKBDIACR:
 	{
-		struct kbdiacr *diacr;
+		struct kbdiacrs __user *a = udp;
+		struct kbdiacr *dia;
 		int i;
 
-		diacr = kmalloc(MAX_DIACR * sizeof(struct kbdiacr),
+		dia = kmalloc(MAX_DIACR * sizeof(struct kbdiacr),
 								GFP_KERNEL);
-		if (diacr == NULL)
+		if (!dia)
 			return -ENOMEM;
 
 		/* Lock the diacriticals table, make a copy and then
@@ -1542,26 +1542,26 @@
 
 		asize = accent_table_size;
 		for (i = 0; i < asize; i++) {
-			diacr[i].diacr = conv_uni_to_8bit(
+			dia[i].diacr = conv_uni_to_8bit(
 						accent_table[i].diacr);
-			diacr[i].base = conv_uni_to_8bit(
+			dia[i].base = conv_uni_to_8bit(
 						accent_table[i].base);
-			diacr[i].result = conv_uni_to_8bit(
+			dia[i].result = conv_uni_to_8bit(
 						accent_table[i].result);
 		}
 		spin_unlock_irqrestore(&kbd_event_lock, flags);
 
 		if (put_user(asize, &a->kb_cnt))
 			ret = -EFAULT;
-		else  if (copy_to_user(a->kbdiacr, diacr,
+		else  if (copy_to_user(a->kbdiacr, dia,
 				asize * sizeof(struct kbdiacr)))
 			ret = -EFAULT;
-		kfree(diacr);
+		kfree(dia);
 		return ret;
 	}
 	case KDGKBDIACRUC:
 	{
-		struct kbdiacrsuc __user *a = up;
+		struct kbdiacrsuc __user *a = udp;
 		void *buf;
 
 		buf = kmalloc(MAX_DIACR * sizeof(struct kbdiacruc),
@@ -1589,8 +1589,8 @@
 
 	case KDSKBDIACR:
 	{
-		struct kbdiacrs __user *a = up;
-		struct kbdiacr *diacr = NULL;
+		struct kbdiacrs __user *a = udp;
+		struct kbdiacr *dia = NULL;
 		unsigned int ct;
 		int i;
 
@@ -1602,14 +1602,14 @@
 			return -EINVAL;
 
 		if (ct) {
-			diacr = kmalloc(sizeof(struct kbdiacr) * ct,
+			dia = kmalloc(sizeof(struct kbdiacr) * ct,
 								GFP_KERNEL);
-			if (diacr == NULL)
+			if (!dia)
 				return -ENOMEM;
 
-			if (copy_from_user(diacr, a->kbdiacr,
+			if (copy_from_user(dia, a->kbdiacr,
 					sizeof(struct kbdiacr) * ct)) {
-				kfree(diacr);
+				kfree(dia);
 				return -EFAULT;
 			}
 		}
@@ -1618,20 +1618,20 @@
 		accent_table_size = ct;
 		for (i = 0; i < ct; i++) {
 			accent_table[i].diacr =
-					conv_8bit_to_uni(diacr[i].diacr);
+					conv_8bit_to_uni(dia[i].diacr);
 			accent_table[i].base =
-					conv_8bit_to_uni(diacr[i].base);
+					conv_8bit_to_uni(dia[i].base);
 			accent_table[i].result =
-					conv_8bit_to_uni(diacr[i].result);
+					conv_8bit_to_uni(dia[i].result);
 		}
 		spin_unlock_irqrestore(&kbd_event_lock, flags);
-		kfree(diacr);
+		kfree(dia);
 		return 0;
 	}
 
 	case KDSKBDIACRUC:
 	{
-		struct kbdiacrsuc __user *a = up;
+		struct kbdiacrsuc __user *a = udp;
 		unsigned int ct;
 		void *buf = NULL;
 
@@ -1679,28 +1679,28 @@
  */
 int vt_do_kdskbmode(int console, unsigned int arg)
 {
-	struct kbd_struct * kbd = kbd_table + console;
+	struct kbd_struct *kb = kbd_table + console;
 	int ret = 0;
 	unsigned long flags;
 
 	spin_lock_irqsave(&kbd_event_lock, flags);
 	switch(arg) {
 	case K_RAW:
-		kbd->kbdmode = VC_RAW;
+		kb->kbdmode = VC_RAW;
 		break;
 	case K_MEDIUMRAW:
-		kbd->kbdmode = VC_MEDIUMRAW;
+		kb->kbdmode = VC_MEDIUMRAW;
 		break;
 	case K_XLATE:
-		kbd->kbdmode = VC_XLATE;
+		kb->kbdmode = VC_XLATE;
 		do_compute_shiftstate();
 		break;
 	case K_UNICODE:
-		kbd->kbdmode = VC_UNICODE;
+		kb->kbdmode = VC_UNICODE;
 		do_compute_shiftstate();
 		break;
 	case K_OFF:
-		kbd->kbdmode = VC_OFF;
+		kb->kbdmode = VC_OFF;
 		break;
 	default:
 		ret = -EINVAL;
@@ -1719,17 +1719,17 @@
  */
 int vt_do_kdskbmeta(int console, unsigned int arg)
 {
-	struct kbd_struct * kbd = kbd_table + console;
+	struct kbd_struct *kb = kbd_table + console;
 	int ret = 0;
 	unsigned long flags;
 
 	spin_lock_irqsave(&kbd_event_lock, flags);
 	switch(arg) {
 	case K_METABIT:
-		clr_vc_kbd_mode(kbd, VC_META);
+		clr_vc_kbd_mode(kb, VC_META);
 		break;
 	case K_ESCPREFIX:
-		set_vc_kbd_mode(kbd, VC_META);
+		set_vc_kbd_mode(kb, VC_META);
 		break;
 	default:
 		ret = -EINVAL;
@@ -1768,7 +1768,7 @@
 int vt_do_kdsk_ioctl(int cmd, struct kbentry __user *user_kbe, int perm,
 						int console)
 {
-	struct kbd_struct * kbd = kbd_table + console;
+	struct kbd_struct *kb = kbd_table + console;
 	struct kbentry tmp;
 	ushort *key_map, *new_map, val, ov;
 	unsigned long flags;
@@ -1786,7 +1786,7 @@
 		key_map = key_maps[s];
 		if (key_map) {
 		    val = U(key_map[i]);
-		    if (kbd->kbdmode != VC_UNICODE && KTYP(val) >= NR_TYPES)
+		    if (kb->kbdmode != VC_UNICODE && KTYP(val) >= NR_TYPES)
 			val = K_HOLE;
 		} else
 		    val = (i ? K_HOLE : K_NOSUCHMAP);
@@ -1814,7 +1814,7 @@
 		    if (KVAL(v) > max_vals[KTYP(v)])
 				return -EINVAL;
 		} else
-		    if (kbd->kbdmode != VC_UNICODE)
+		    if (kb->kbdmode != VC_UNICODE)
 				return -EINVAL;
 
 		/* ++Geert: non-PC keyboards may generate keycode zero */
@@ -1985,7 +1985,7 @@
 
 int vt_do_kdskled(int console, int cmd, unsigned long arg, int perm)
 {
-	struct kbd_struct * kbd = kbd_table + console;
+	struct kbd_struct *kb = kbd_table + console;
         unsigned long flags;
 	unsigned char ucval;
 
@@ -1994,7 +1994,7 @@
 	/* don't use them - they will go away without warning */
 	case KDGKBLED:
                 spin_lock_irqsave(&kbd_event_lock, flags);
-		ucval = kbd->ledflagstate | (kbd->default_ledflagstate << 4);
+		ucval = kb->ledflagstate | (kb->default_ledflagstate << 4);
                 spin_unlock_irqrestore(&kbd_event_lock, flags);
 		return put_user(ucval, (char __user *)arg);
 
@@ -2004,8 +2004,8 @@
 		if (arg & ~0x77)
 			return -EINVAL;
                 spin_lock_irqsave(&led_lock, flags);
-		kbd->ledflagstate = (arg & 7);
-		kbd->default_ledflagstate = ((arg >> 4) & 7);
+		kb->ledflagstate = (arg & 7);
+		kb->default_ledflagstate = ((arg >> 4) & 7);
 		set_leds();
                 spin_unlock_irqrestore(&led_lock, flags);
 		return 0;
@@ -2019,7 +2019,7 @@
 	case KDSETLED:
 		if (!perm)
 			return -EPERM;
-		setledstate(kbd, arg);
+		setledstate(kb, arg);
 		return 0;
         }
         return -ENOIOCTLCMD;
@@ -2027,9 +2027,9 @@
 
 int vt_do_kdgkbmode(int console)
 {
-	struct kbd_struct * kbd = kbd_table + console;
+	struct kbd_struct *kb = kbd_table + console;
 	/* This is a spot read so needs no locking */
-	switch (kbd->kbdmode) {
+	switch (kb->kbdmode) {
 	case VC_RAW:
 		return K_RAW;
 	case VC_MEDIUMRAW:
@@ -2051,9 +2051,9 @@
  */
 int vt_do_kdgkbmeta(int console)
 {
-	struct kbd_struct * kbd = kbd_table + console;
+	struct kbd_struct *kb = kbd_table + console;
         /* Again a spot read so no locking */
-	return vc_kbd_mode(kbd, VC_META) ? K_ESCPREFIX : K_METABIT;
+	return vc_kbd_mode(kb, VC_META) ? K_ESCPREFIX : K_METABIT;
 }
 
 /**
@@ -2092,19 +2092,19 @@
  */
 void vt_reset_keyboard(int console)
 {
-	struct kbd_struct * kbd = kbd_table + console;
+	struct kbd_struct *kb = kbd_table + console;
 	unsigned long flags;
 
 	spin_lock_irqsave(&kbd_event_lock, flags);
-	set_vc_kbd_mode(kbd, VC_REPEAT);
-	clr_vc_kbd_mode(kbd, VC_CKMODE);
-	clr_vc_kbd_mode(kbd, VC_APPLIC);
-	clr_vc_kbd_mode(kbd, VC_CRLF);
-	kbd->lockstate = 0;
-	kbd->slockstate = 0;
+	set_vc_kbd_mode(kb, VC_REPEAT);
+	clr_vc_kbd_mode(kb, VC_CKMODE);
+	clr_vc_kbd_mode(kb, VC_APPLIC);
+	clr_vc_kbd_mode(kb, VC_CRLF);
+	kb->lockstate = 0;
+	kb->slockstate = 0;
 	spin_lock(&led_lock);
-	kbd->ledmode = LED_SHOW_FLAGS;
-	kbd->ledflagstate = kbd->default_ledflagstate;
+	kb->ledmode = LED_SHOW_FLAGS;
+	kb->ledflagstate = kb->default_ledflagstate;
 	spin_unlock(&led_lock);
 	/* do not do set_leds here because this causes an endless tasklet loop
 	   when the keyboard hasn't been initialized yet */
@@ -2122,8 +2122,8 @@
 
 int vt_get_kbd_mode_bit(int console, int bit)
 {
-	struct kbd_struct * kbd = kbd_table + console;
-	return vc_kbd_mode(kbd, bit);
+	struct kbd_struct *kb = kbd_table + console;
+	return vc_kbd_mode(kb, bit);
 }
 
 /**
@@ -2137,11 +2137,11 @@
 
 void vt_set_kbd_mode_bit(int console, int bit)
 {
-	struct kbd_struct * kbd = kbd_table + console;
+	struct kbd_struct *kb = kbd_table + console;
 	unsigned long flags;
 
 	spin_lock_irqsave(&kbd_event_lock, flags);
-	set_vc_kbd_mode(kbd, bit);
+	set_vc_kbd_mode(kb, bit);
 	spin_unlock_irqrestore(&kbd_event_lock, flags);
 }
 
@@ -2156,10 +2156,10 @@
 
 void vt_clr_kbd_mode_bit(int console, int bit)
 {
-	struct kbd_struct * kbd = kbd_table + console;
+	struct kbd_struct *kb = kbd_table + console;
 	unsigned long flags;
 
 	spin_lock_irqsave(&kbd_event_lock, flags);
-	clr_vc_kbd_mode(kbd, bit);
+	clr_vc_kbd_mode(kb, bit);
 	spin_unlock_irqrestore(&kbd_event_lock, flags);
 }
diff --git a/drivers/usb/serial/digi_acceleport.c b/drivers/usb/serial/digi_acceleport.c
index 8a23c53..12b0e67 100644
--- a/drivers/usb/serial/digi_acceleport.c
+++ b/drivers/usb/serial/digi_acceleport.c
@@ -834,7 +834,6 @@
 			arg |= DIGI_OUTPUT_FLOW_CONTROL_CTS;
 		} else {
 			arg &= ~DIGI_OUTPUT_FLOW_CONTROL_CTS;
-			tty->hw_stopped = 0;
 		}
 
 		buf[i++] = DIGI_CMD_SET_OUTPUT_FLOW_CONTROL;
@@ -1500,15 +1499,11 @@
 			if (val & DIGI_READ_INPUT_SIGNALS_CTS) {
 				priv->dp_modem_signals |= TIOCM_CTS;
 				/* port must be open to use tty struct */
-				if (rts) {
-					tty->hw_stopped = 0;
+				if (rts)
 					tty_port_tty_wakeup(&port->port);
-				}
 			} else {
 				priv->dp_modem_signals &= ~TIOCM_CTS;
 				/* port must be open to use tty struct */
-				if (rts)
-					tty->hw_stopped = 1;
 			}
 			if (val & DIGI_READ_INPUT_SIGNALS_DSR)
 				priv->dp_modem_signals |= TIOCM_DSR;
diff --git a/drivers/usb/serial/io_ti.c b/drivers/usb/serial/io_ti.c
index c0a42e9..ddbb8fe 100644
--- a/drivers/usb/serial/io_ti.c
+++ b/drivers/usb/serial/io_ti.c
@@ -1456,12 +1456,8 @@
 	tty = tty_port_tty_get(&edge_port->port->port);
 	/* handle CTS flow control */
 	if (tty && C_CRTSCTS(tty)) {
-		if (msr & EDGEPORT_MSR_CTS) {
-			tty->hw_stopped = 0;
+		if (msr & EDGEPORT_MSR_CTS)
 			tty_wakeup(tty);
-		} else {
-			tty->hw_stopped = 1;
-		}
 	}
 	tty_kref_put(tty);
 }
@@ -2177,7 +2173,6 @@
 		dev_dbg(dev, "%s - RTS/CTS is enabled\n", __func__);
 	} else {
 		dev_dbg(dev, "%s - RTS/CTS is disabled\n", __func__);
-		tty->hw_stopped = 0;
 		restart_read(edge_port);
 	}
 
diff --git a/drivers/usb/serial/ti_usb_3410_5052.c b/drivers/usb/serial/ti_usb_3410_5052.c
index 3dd3ff8..e9da41d 100644
--- a/drivers/usb/serial/ti_usb_3410_5052.c
+++ b/drivers/usb/serial/ti_usb_3410_5052.c
@@ -773,7 +773,6 @@
 			config->wFlags |= TI_UART_ENABLE_RTS_IN;
 		config->wFlags |= TI_UART_ENABLE_CTS_OUT;
 	} else {
-		tty->hw_stopped = 0;
 		ti_restart_read(tport, tty);
 	}
 
@@ -1291,12 +1290,8 @@
 	/* handle CTS flow control */
 	tty = tty_port_tty_get(&tport->tp_port->port);
 	if (tty && C_CRTSCTS(tty)) {
-		if (msr & TI_MSR_CTS) {
-			tty->hw_stopped = 0;
+		if (msr & TI_MSR_CTS)
 			tty_wakeup(tty);
-		} else {
-			tty->hw_stopped = 1;
-		}
 	}
 	tty_kref_put(tty);
 }
diff --git a/include/linux/lockdep.h b/include/linux/lockdep.h
index 008388f9..64c7425 100644
--- a/include/linux/lockdep.h
+++ b/include/linux/lockdep.h
@@ -362,6 +362,10 @@
 		WARN_ON(debug_locks && !lockdep_is_held(l));	\
 	} while (0)
 
+#define lockdep_assert_held_once(l)	do {				\
+		WARN_ON_ONCE(debug_locks && !lockdep_is_held(l));	\
+	} while (0)
+
 #define lockdep_recursing(tsk)	((tsk)->lockdep_recursion)
 
 #else /* !CONFIG_LOCKDEP */
@@ -412,6 +416,7 @@
 #define lockdep_depth(tsk)	(0)
 
 #define lockdep_assert_held(l)			do { (void)(l); } while (0)
+#define lockdep_assert_held_once(l)		do { (void)(l); } while (0)
 
 #define lockdep_recursing(tsk)			(0)
 
diff --git a/include/linux/serial_8250.h b/include/linux/serial_8250.h
index f93649e..3df10d5 100644
--- a/include/linux/serial_8250.h
+++ b/include/linux/serial_8250.h
@@ -84,6 +84,7 @@
 	unsigned char		mcr_mask;	/* mask of user bits */
 	unsigned char		mcr_force;	/* mask of forced bits */
 	unsigned char		cur_iotype;	/* Running I/O type */
+	unsigned int		rpm_tx_active;
 
 	/*
 	 * Some bits in registers are cleared on a read, so they must
@@ -96,10 +97,13 @@
 	unsigned char		msr_saved_flags;
 
 	struct uart_8250_dma	*dma;
+	struct serial_rs485     rs485;
 
 	/* 8250 specific callbacks */
 	int			(*dl_read)(struct uart_8250_port *);
 	void			(*dl_write)(struct uart_8250_port *, int);
+	int			(*rs485_config)(struct uart_8250_port *,
+						struct serial_rs485 *rs485);
 };
 
 static inline struct uart_8250_port *up_to_u8250p(struct uart_port *up)
@@ -121,6 +125,8 @@
 extern int setup_early_serial8250_console(char *cmdline);
 extern void serial8250_do_set_termios(struct uart_port *port,
 		struct ktermios *termios, struct ktermios *old);
+extern int serial8250_do_startup(struct uart_port *port);
+extern void serial8250_do_shutdown(struct uart_port *port);
 extern void serial8250_do_pm(struct uart_port *port, unsigned int state,
 			     unsigned int oldstate);
 extern int fsl8250_handle_irq(struct uart_port *port);
diff --git a/include/linux/serial_core.h b/include/linux/serial_core.h
index cf3a1e7..21c2e05 100644
--- a/include/linux/serial_core.h
+++ b/include/linux/serial_core.h
@@ -112,6 +112,7 @@
 };
 
 typedef unsigned int __bitwise__ upf_t;
+typedef unsigned int __bitwise__ upstat_t;
 
 struct uart_port {
 	spinlock_t		lock;			/* port lock */
@@ -122,6 +123,10 @@
 	void			(*set_termios)(struct uart_port *,
 				               struct ktermios *new,
 				               struct ktermios *old);
+	int			(*startup)(struct uart_port *port);
+	void			(*shutdown)(struct uart_port *port);
+	void			(*throttle)(struct uart_port *port);
+	void			(*unthrottle)(struct uart_port *port);
 	int			(*handle_irq)(struct uart_port *);
 	void			(*pm)(struct uart_port *, unsigned int state,
 				      unsigned int old);
@@ -152,6 +157,7 @@
 	unsigned long		sysrq;			/* sysrq timeout */
 #endif
 
+	/* flags must be updated while holding port mutex */
 	upf_t			flags;
 
 #define UPF_FOURPORT		((__force upf_t) (1 << 1))
@@ -187,6 +193,13 @@
 #define UPF_CHANGE_MASK		((__force upf_t) (0x17fff))
 #define UPF_USR_MASK		((__force upf_t) (UPF_SPD_MASK|UPF_LOW_LATENCY))
 
+	/* status must be updated while holding port lock */
+	upstat_t		status;
+
+#define UPSTAT_CTS_ENABLE	((__force upstat_t) (1 << 0))
+#define UPSTAT_DCD_ENABLE	((__force upstat_t) (1 << 1))
+
+	int			hw_stopped;		/* sw-assisted CTS flow state */
 	unsigned int		mctrl;			/* current modem ctrl settings */
 	unsigned int		timeout;		/* character-based timeout */
 	unsigned int		type;			/* port type */
@@ -347,11 +360,16 @@
 static inline int uart_tx_stopped(struct uart_port *port)
 {
 	struct tty_struct *tty = port->state->port.tty;
-	if(tty->stopped || tty->hw_stopped)
+	if (tty->stopped || port->hw_stopped)
 		return 1;
 	return 0;
 }
 
+static inline bool uart_cts_enabled(struct uart_port *uport)
+{
+	return uport->status & UPSTAT_CTS_ENABLE;
+}
+
 /*
  * The following are helper functions for the low level drivers.
  */
diff --git a/include/linux/tty.h b/include/linux/tty.h
index 8413294..5171ef8 100644
--- a/include/linux/tty.h
+++ b/include/linux/tty.h
@@ -252,6 +252,7 @@
 	struct rw_semaphore termios_rwsem;
 	struct mutex winsize_mutex;
 	spinlock_t ctrl_lock;
+	spinlock_t flow_lock;
 	/* Termios values are protected by the termios rwsem */
 	struct ktermios termios, termios_locked;
 	struct termiox *termiox;	/* May be NULL for unsupported */
@@ -261,8 +262,13 @@
 	unsigned long flags;
 	int count;
 	struct winsize winsize;		/* winsize_mutex */
-	unsigned char stopped:1, hw_stopped:1, flow_stopped:1, packet:1;
-	unsigned char ctrl_status;	/* ctrl_lock */
+	unsigned long stopped:1,	/* flow_lock */
+		      flow_stopped:1,
+		      unused:BITS_PER_LONG - 2;
+	int hw_stopped;
+	unsigned long ctrl_status:8,	/* ctrl_lock */
+		      packet:1,
+		      unused_ctrl:BITS_PER_LONG - 9;
 	unsigned int receive_room;	/* Bytes free for queue */
 	int flow_change;
 
@@ -397,7 +403,9 @@
 extern char *tty_name(struct tty_struct *tty, char *buf);
 extern void tty_wait_until_sent(struct tty_struct *tty, long timeout);
 extern int tty_check_change(struct tty_struct *tty);
+extern void __stop_tty(struct tty_struct *tty);
 extern void stop_tty(struct tty_struct *tty);
+extern void __start_tty(struct tty_struct *tty);
 extern void start_tty(struct tty_struct *tty);
 extern int tty_register_driver(struct tty_driver *driver);
 extern int tty_unregister_driver(struct tty_driver *driver);
@@ -411,6 +419,7 @@
 extern int tty_read_raw_data(struct tty_struct *tty, unsigned char *bufp,
 			     int buflen);
 extern void tty_write_message(struct tty_struct *tty, char *msg);
+extern int tty_send_xchar(struct tty_struct *tty, char ch);
 extern int tty_put_char(struct tty_struct *tty, unsigned char c);
 extern int tty_chars_in_buffer(struct tty_struct *tty);
 extern int tty_write_room(struct tty_struct *tty);
@@ -495,8 +504,6 @@
 extern struct mutex tty_mutex;
 extern spinlock_t tty_files_lock;
 
-extern void tty_write_unlock(struct tty_struct *tty);
-extern int tty_write_lock(struct tty_struct *tty, int ndelay);
 #define tty_is_writelocked(tty)  (mutex_is_locked(&tty->atomic_write_lock))
 
 extern void tty_port_init(struct tty_port *port);
diff --git a/include/linux/tty_driver.h b/include/linux/tty_driver.h
index e48c608..92e337c 100644
--- a/include/linux/tty_driver.h
+++ b/include/linux/tty_driver.h
@@ -152,6 +152,8 @@
  * 	This routine notifies the tty driver that it should stop
  * 	outputting characters to the tty device.  
  *
+ *	Called with ->flow_lock held. Serialized with start() method.
+ *
  *	Optional:
  *
  *	Note: Call stop_tty not this method.
@@ -161,6 +163,8 @@
  * 	This routine notifies the tty driver that it resume sending
  *	characters to the tty device.
  *
+ *	Called with ->flow_lock held. Serialized with stop() method.
+ *
  *	Optional:
  *
  *	Note: Call start_tty not this method.
diff --git a/include/uapi/linux/serial_core.h b/include/uapi/linux/serial_core.h
index 5820269..16ad852 100644
--- a/include/uapi/linux/serial_core.h
+++ b/include/uapi/linux/serial_core.h
@@ -244,4 +244,7 @@
 /* SC16IS74xx */
 #define PORT_SC16IS7XX   108
 
+/* MESON */
+#define PORT_MESON	109
+
 #endif /* _UAPILINUX_SERIAL_CORE_H */