| /* |
| * linux/arch/arm/plat-omap/sram.c |
| * |
| * OMAP SRAM detection and management |
| * |
| * Copyright (C) 2005 Nokia Corporation |
| * Written by Tony Lindgren <tony@atomide.com> |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 as |
| * published by the Free Software Foundation. |
| */ |
| |
| #include <linux/module.h> |
| #include <linux/kernel.h> |
| #include <linux/init.h> |
| |
| #include <asm/tlb.h> |
| #include <asm/io.h> |
| #include <asm/cacheflush.h> |
| |
| #include <asm/mach/map.h> |
| |
| #include <asm/arch/sram.h> |
| #include <asm/arch/board.h> |
| |
| #define OMAP1_SRAM_PA 0x20000000 |
| #define OMAP1_SRAM_VA 0xd0000000 |
| #define OMAP2_SRAM_PA 0x40200000 |
| #define OMAP2_SRAM_PUB_PA 0x4020f800 |
| #define OMAP2_SRAM_VA 0xd0000000 |
| #define OMAP2_SRAM_PUB_VA 0xd0000800 |
| |
| #if defined(CONFIG_ARCH_OMAP24XX) |
| #define SRAM_BOOTLOADER_SZ 0x00 |
| #else |
| #define SRAM_BOOTLOADER_SZ 0x80 |
| #endif |
| |
| #define VA_REQINFOPERM0 IO_ADDRESS(0x68005048) |
| #define VA_READPERM0 IO_ADDRESS(0x68005050) |
| #define VA_WRITEPERM0 IO_ADDRESS(0x68005058) |
| #define VA_CONTROL_STAT IO_ADDRESS(0x480002F8) |
| #define GP_DEVICE 0x300 |
| #define TYPE_MASK 0x700 |
| |
| #define ROUND_DOWN(value,boundary) ((value) & (~((boundary)-1))) |
| |
| static unsigned long omap_sram_base; |
| static unsigned long omap_sram_size; |
| static unsigned long omap_sram_ceil; |
| |
| unsigned long omap_fb_sram_start; |
| unsigned long omap_fb_sram_size; |
| |
| /* Depending on the target RAMFS firewall setup, the public usable amount of |
| * SRAM varies. The default accessable size for all device types is 2k. A GP |
| * device allows ARM11 but not other initators for full size. This |
| * functionality seems ok until some nice security API happens. |
| */ |
| static int is_sram_locked(void) |
| { |
| int type = 0; |
| |
| if (cpu_is_omap242x()) |
| type = __raw_readl(VA_CONTROL_STAT) & TYPE_MASK; |
| |
| if (type == GP_DEVICE) { |
| /* RAMFW: R/W access to all initators for all qualifier sets */ |
| if (cpu_is_omap242x()) { |
| __raw_writel(0xFF, VA_REQINFOPERM0); /* all q-vects */ |
| __raw_writel(0xCFDE, VA_READPERM0); /* all i-read */ |
| __raw_writel(0xCFDE, VA_WRITEPERM0); /* all i-write */ |
| } |
| return 0; |
| } else |
| return 1; /* assume locked with no PPA or security driver */ |
| } |
| |
| void get_fb_sram_conf(unsigned long start_avail, unsigned size_avail, |
| unsigned long *start, unsigned long *size) |
| { |
| const struct omap_fbmem_config *fbmem_conf; |
| |
| fbmem_conf = omap_get_config(OMAP_TAG_FBMEM, struct omap_fbmem_config); |
| if (fbmem_conf != NULL) { |
| *start = fbmem_conf->fb_sram_start; |
| *size = fbmem_conf->fb_sram_size; |
| } else { |
| *size = 0; |
| *start = 0; |
| } |
| |
| if (*size && ( |
| *start < start_avail || |
| *start + *size > start_avail + size_avail)) { |
| printk(KERN_ERR "invalid FB SRAM configuration\n"); |
| *start = start_avail; |
| *size = size_avail; |
| } |
| |
| if (*size) |
| pr_info("Reserving %lu bytes SRAM for frame buffer\n", *size); |
| } |
| |
| /* |
| * The amount of SRAM depends on the core type. |
| * Note that we cannot try to test for SRAM here because writes |
| * to secure SRAM will hang the system. Also the SRAM is not |
| * yet mapped at this point. |
| */ |
| void __init omap_detect_sram(void) |
| { |
| unsigned long sram_start; |
| |
| if (cpu_is_omap24xx()) { |
| if (is_sram_locked()) { |
| omap_sram_base = OMAP2_SRAM_PUB_VA; |
| sram_start = OMAP2_SRAM_PUB_PA; |
| omap_sram_size = 0x800; /* 2K */ |
| } else { |
| omap_sram_base = OMAP2_SRAM_VA; |
| sram_start = OMAP2_SRAM_PA; |
| if (cpu_is_omap242x()) |
| omap_sram_size = 0xa0000; /* 640K */ |
| else if (cpu_is_omap243x()) |
| omap_sram_size = 0x10000; /* 64K */ |
| } |
| } else { |
| omap_sram_base = OMAP1_SRAM_VA; |
| sram_start = OMAP1_SRAM_PA; |
| |
| if (cpu_is_omap730()) |
| omap_sram_size = 0x32000; /* 200K */ |
| else if (cpu_is_omap15xx()) |
| omap_sram_size = 0x30000; /* 192K */ |
| else if (cpu_is_omap1610() || cpu_is_omap1621() || |
| cpu_is_omap1710()) |
| omap_sram_size = 0x4000; /* 16K */ |
| else if (cpu_is_omap1611()) |
| omap_sram_size = 0x3e800; /* 250K */ |
| else { |
| printk(KERN_ERR "Could not detect SRAM size\n"); |
| omap_sram_size = 0x4000; |
| } |
| } |
| get_fb_sram_conf(sram_start + SRAM_BOOTLOADER_SZ, |
| omap_sram_size - SRAM_BOOTLOADER_SZ, |
| &omap_fb_sram_start, &omap_fb_sram_size); |
| if (omap_fb_sram_size) |
| omap_sram_size -= sram_start + omap_sram_size - |
| omap_fb_sram_start; |
| omap_sram_ceil = omap_sram_base + omap_sram_size; |
| } |
| |
| static struct map_desc omap_sram_io_desc[] __initdata = { |
| { /* .length gets filled in at runtime */ |
| .virtual = OMAP1_SRAM_VA, |
| .pfn = __phys_to_pfn(OMAP1_SRAM_PA), |
| .type = MT_DEVICE |
| } |
| }; |
| |
| /* |
| * In order to use last 2kB of SRAM on 1611b, we must round the size |
| * up to multiple of PAGE_SIZE. We cannot use ioremap for SRAM, as |
| * clock init needs SRAM early. |
| */ |
| void __init omap_map_sram(void) |
| { |
| unsigned long base; |
| |
| if (omap_sram_size == 0) |
| return; |
| |
| if (cpu_is_omap24xx()) { |
| omap_sram_io_desc[0].virtual = OMAP2_SRAM_VA; |
| |
| if (is_sram_locked()) |
| base = OMAP2_SRAM_PUB_PA; |
| else |
| base = OMAP2_SRAM_PA; |
| base = ROUND_DOWN(base, PAGE_SIZE); |
| omap_sram_io_desc[0].pfn = __phys_to_pfn(base); |
| } |
| |
| omap_sram_io_desc[0].length = (omap_sram_size + PAGE_SIZE-1)/PAGE_SIZE; |
| omap_sram_io_desc[0].length *= PAGE_SIZE; |
| iotable_init(omap_sram_io_desc, ARRAY_SIZE(omap_sram_io_desc)); |
| |
| printk(KERN_INFO "SRAM: Mapped pa 0x%08lx to va 0x%08lx size: 0x%lx\n", |
| __pfn_to_phys(omap_sram_io_desc[0].pfn), |
| omap_sram_io_desc[0].virtual, |
| omap_sram_io_desc[0].length); |
| |
| /* |
| * Normally devicemaps_init() would flush caches and tlb after |
| * mdesc->map_io(), but since we're called from map_io(), we |
| * must do it here. |
| */ |
| local_flush_tlb_all(); |
| flush_cache_all(); |
| |
| /* |
| * Looks like we need to preserve some bootloader code at the |
| * beginning of SRAM for jumping to flash for reboot to work... |
| */ |
| memset((void *)omap_sram_base + SRAM_BOOTLOADER_SZ, 0, |
| omap_sram_size - SRAM_BOOTLOADER_SZ); |
| } |
| |
| void * omap_sram_push(void * start, unsigned long size) |
| { |
| if (size > (omap_sram_ceil - (omap_sram_base + SRAM_BOOTLOADER_SZ))) { |
| printk(KERN_ERR "Not enough space in SRAM\n"); |
| return NULL; |
| } |
| |
| omap_sram_ceil -= size; |
| omap_sram_ceil = ROUND_DOWN(omap_sram_ceil, sizeof(void *)); |
| memcpy((void *)omap_sram_ceil, start, size); |
| |
| return (void *)omap_sram_ceil; |
| } |
| |
| static void omap_sram_error(void) |
| { |
| panic("Uninitialized SRAM function\n"); |
| } |
| |
| #ifdef CONFIG_ARCH_OMAP1 |
| |
| static void (*_omap_sram_reprogram_clock)(u32 dpllctl, u32 ckctl); |
| |
| void omap_sram_reprogram_clock(u32 dpllctl, u32 ckctl) |
| { |
| if (!_omap_sram_reprogram_clock) |
| omap_sram_error(); |
| |
| return _omap_sram_reprogram_clock(dpllctl, ckctl); |
| } |
| |
| int __init omap1_sram_init(void) |
| { |
| _omap_sram_reprogram_clock = omap_sram_push(sram_reprogram_clock, |
| sram_reprogram_clock_sz); |
| |
| return 0; |
| } |
| |
| #else |
| #define omap1_sram_init() do {} while (0) |
| #endif |
| |
| #ifdef CONFIG_ARCH_OMAP2 |
| |
| static void (*_omap2_sram_ddr_init)(u32 *slow_dll_ctrl, u32 fast_dll_ctrl, |
| u32 base_cs, u32 force_unlock); |
| |
| void omap2_sram_ddr_init(u32 *slow_dll_ctrl, u32 fast_dll_ctrl, |
| u32 base_cs, u32 force_unlock) |
| { |
| if (!_omap2_sram_ddr_init) |
| omap_sram_error(); |
| |
| return _omap2_sram_ddr_init(slow_dll_ctrl, fast_dll_ctrl, |
| base_cs, force_unlock); |
| } |
| |
| static void (*_omap2_sram_reprogram_sdrc)(u32 perf_level, u32 dll_val, |
| u32 mem_type); |
| |
| void omap2_sram_reprogram_sdrc(u32 perf_level, u32 dll_val, u32 mem_type) |
| { |
| if (!_omap2_sram_reprogram_sdrc) |
| omap_sram_error(); |
| |
| return _omap2_sram_reprogram_sdrc(perf_level, dll_val, mem_type); |
| } |
| |
| static u32 (*_omap2_set_prcm)(u32 dpll_ctrl_val, u32 sdrc_rfr_val, int bypass); |
| |
| u32 omap2_set_prcm(u32 dpll_ctrl_val, u32 sdrc_rfr_val, int bypass) |
| { |
| if (!_omap2_set_prcm) |
| omap_sram_error(); |
| |
| return _omap2_set_prcm(dpll_ctrl_val, sdrc_rfr_val, bypass); |
| } |
| |
| int __init omap2_sram_init(void) |
| { |
| _omap2_sram_ddr_init = omap_sram_push(sram_ddr_init, sram_ddr_init_sz); |
| |
| _omap2_sram_reprogram_sdrc = omap_sram_push(sram_reprogram_sdrc, |
| sram_reprogram_sdrc_sz); |
| _omap2_set_prcm = omap_sram_push(sram_set_prcm, sram_set_prcm_sz); |
| |
| return 0; |
| } |
| #else |
| #define omap2_sram_init() do {} while (0) |
| #endif |
| |
| int __init omap_sram_init(void) |
| { |
| omap_detect_sram(); |
| omap_map_sram(); |
| |
| if (!cpu_is_omap24xx()) |
| omap1_sram_init(); |
| else |
| omap2_sram_init(); |
| |
| return 0; |
| } |