blob: 8074ac56f479b26eab53801f9816564eaabbef68 [file] [log] [blame]
/***************************************************************************/
/*
* linux/arch/m68knommu/platform/5307/config.c
*
* Copyright (C) 1999-2002, Greg Ungerer (gerg@snapgear.com)
* Copyright (C) 2000, Lineo (www.lineo.com)
*/
/***************************************************************************/
#include <linux/kernel.h>
#include <linux/sched.h>
#include <linux/param.h>
#include <linux/init.h>
#include <linux/interrupt.h>
#include <asm/irq.h>
#include <asm/dma.h>
#include <asm/traps.h>
#include <asm/machdep.h>
#include <asm/coldfire.h>
#include <asm/mcftimer.h>
#include <asm/mcfsim.h>
#include <asm/mcfdma.h>
#include <asm/mcfwdebug.h>
/***************************************************************************/
void coldfire_tick(void);
void coldfire_timer_init(irqreturn_t (*handler)(int, void *, struct pt_regs *));
unsigned long coldfire_timer_offset(void);
void coldfire_trap_init(void);
void coldfire_reset(void);
extern unsigned int mcf_timervector;
extern unsigned int mcf_profilevector;
extern unsigned int mcf_timerlevel;
/***************************************************************************/
/*
* Some platforms need software versions of the GPIO data registers.
*/
unsigned short ppdata;
unsigned char ledbank = 0xff;
/***************************************************************************/
/*
* DMA channel base address table.
*/
unsigned int dma_base_addr[MAX_M68K_DMA_CHANNELS] = {
MCF_MBAR + MCFDMA_BASE0,
MCF_MBAR + MCFDMA_BASE1,
MCF_MBAR + MCFDMA_BASE2,
MCF_MBAR + MCFDMA_BASE3,
};
unsigned int dma_device_address[MAX_M68K_DMA_CHANNELS];
/***************************************************************************/
void mcf_autovector(unsigned int vec)
{
volatile unsigned char *mbar;
if ((vec >= 25) && (vec <= 31)) {
mbar = (volatile unsigned char *) MCF_MBAR;
vec = 0x1 << (vec - 24);
*(mbar + MCFSIM_AVR) |= vec;
mcf_setimr(mcf_getimr() & ~vec);
}
}
/***************************************************************************/
void mcf_settimericr(unsigned int timer, unsigned int level)
{
volatile unsigned char *icrp;
unsigned int icr, imr;
if (timer <= 2) {
switch (timer) {
case 2: icr = MCFSIM_TIMER2ICR; imr = MCFSIM_IMR_TIMER2; break;
default: icr = MCFSIM_TIMER1ICR; imr = MCFSIM_IMR_TIMER1; break;
}
icrp = (volatile unsigned char *) (MCF_MBAR + icr);
*icrp = MCFSIM_ICR_AUTOVEC | (level << 2) | MCFSIM_ICR_PRI3;
mcf_setimr(mcf_getimr() & ~imr);
}
}
/***************************************************************************/
int mcf_timerirqpending(int timer)
{
unsigned int imr = 0;
switch (timer) {
case 1: imr = MCFSIM_IMR_TIMER1; break;
case 2: imr = MCFSIM_IMR_TIMER2; break;
default: break;
}
return (mcf_getipr() & imr);
}
/***************************************************************************/
void config_BSP(char *commandp, int size)
{
mcf_setimr(MCFSIM_IMR_MASKALL);
#if defined(CONFIG_BOOTPARAM)
strncpy(commandp, CONFIG_BOOTPARAM_STRING, size);
commandp[size-1] = 0;
#elif defined(CONFIG_NETtel) || defined(CONFIG_eLIA) || \
defined(CONFIG_DISKtel) || defined(CONFIG_SECUREEDGEMP3) || \
defined(CONFIG_CLEOPATRA)
/* Copy command line from FLASH to local buffer... */
memcpy(commandp, (char *) 0xf0004000, size);
commandp[size-1] = 0;
/* Different timer setup - to prevent device clash */
mcf_timervector = 30;
mcf_profilevector = 31;
mcf_timerlevel = 6;
#else
memset(commandp, 0, size);
#endif
mach_sched_init = coldfire_timer_init;
mach_tick = coldfire_tick;
mach_gettimeoffset = coldfire_timer_offset;
mach_trap_init = coldfire_trap_init;
mach_reset = coldfire_reset;
#ifdef MCF_BDM_DISABLE
/*
* Disable the BDM clocking. This also turns off most of the rest of
* the BDM device. This is good for EMC reasons. This option is not
* incompatible with the memory protection option.
*/
wdebug(MCFDEBUG_CSR, MCFDEBUG_CSR_PSTCLK);
#endif
}
/***************************************************************************/