Merge tag 'for-3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-testing
Kishon writes:
Adds a new Rockchip PHY driver and contains miscellaneous fixes.
diff --git a/Documentation/devicetree/bindings/phy/phy-miphy28lp.txt b/Documentation/devicetree/bindings/phy/phy-miphy28lp.txt
index 46a135d..89caa88 100644
--- a/Documentation/devicetree/bindings/phy/phy-miphy28lp.txt
+++ b/Documentation/devicetree/bindings/phy/phy-miphy28lp.txt
@@ -26,6 +26,7 @@
filled in "reg". It can also contain the offset of the system configuration
registers used as glue-logic to setup the device for SATA/PCIe or USB3
devices.
+- st,syscfg : Offset of the parent configuration register.
- resets : phandle to the parent reset controller.
- reset-names : Associated name must be "miphy-sw-rst".
@@ -54,18 +55,12 @@
phy_port0: port@9b22000 {
reg = <0x9b22000 0xff>,
<0x9b09000 0xff>,
- <0x9b04000 0xff>,
- <0x114 0x4>, /* sysctrl MiPHY cntrl */
- <0x818 0x4>, /* sysctrl MiPHY status*/
- <0xe0 0x4>, /* sysctrl PCIe */
- <0xec 0x4>; /* sysctrl SATA */
+ <0x9b04000 0xff>;
reg-names = "sata-up",
"pcie-up",
- "pipew",
- "miphy-ctrl-glue",
- "miphy-status-glue",
- "pcie-glue",
- "sata-glue";
+ "pipew";
+
+ st,syscfg = <0x114 0x818 0xe0 0xec>;
#phy-cells = <1>;
st,osc-rdy;
reset-names = "miphy-sw-rst";
@@ -75,18 +70,13 @@
phy_port1: port@9b2a000 {
reg = <0x9b2a000 0xff>,
<0x9b19000 0xff>,
- <0x9b14000 0xff>,
- <0x118 0x4>,
- <0x81c 0x4>,
- <0xe4 0x4>,
- <0xf0 0x4>;
+ <0x9b14000 0xff>;
reg-names = "sata-up",
"pcie-up",
- "pipew",
- "miphy-ctrl-glue",
- "miphy-status-glue",
- "pcie-glue",
- "sata-glue";
+ "pipew";
+
+ st,syscfg = <0x118 0x81c 0xe4 0xf0>;
+
#phy-cells = <1>;
st,osc-force-ext;
reset-names = "miphy-sw-rst";
@@ -95,13 +85,12 @@
phy_port2: port@8f95000 {
reg = <0x8f95000 0xff>,
- <0x8f90000 0xff>,
- <0x11c 0x4>,
- <0x820 0x4>;
+ <0x8f90000 0xff>;
reg-names = "pipew",
- "usb3-up",
- "miphy-ctrl-glue",
- "miphy-status-glue";
+ "usb3-up";
+
+ st,syscfg = <0x11c 0x820>;
+
#phy-cells = <1>;
reset-names = "miphy-sw-rst";
resets = <&softreset STIH407_MIPHY2_SOFTRESET>;
@@ -125,4 +114,4 @@
Macro definitions for the supported miphy configuration can be found in:
-include/dt-bindings/phy/phy-miphy28lp.h
+include/dt-bindings/phy/phy.h
diff --git a/Documentation/devicetree/bindings/phy/phy-miphy365x.txt b/Documentation/devicetree/bindings/phy/phy-miphy365x.txt
index 42c8808..9802d5d 100644
--- a/Documentation/devicetree/bindings/phy/phy-miphy365x.txt
+++ b/Documentation/devicetree/bindings/phy/phy-miphy365x.txt
@@ -6,8 +6,10 @@
Required properties (controller (parent) node):
- compatible : Should be "st,miphy365x-phy"
-- st,syscfg : Should be a phandle of the system configuration register group
- which contain the SATA, PCIe mode setting bits
+- st,syscfg : Phandle / integer array property. Phandle of sysconfig group
+ containing the miphy registers and integer array should contain
+ an entry for each port sub-node, specifying the control
+ register offset inside the sysconfig group.
Required nodes : A sub-node is required for each channel the controller
provides. Address range information including the usual
@@ -26,7 +28,6 @@
registers filled in "reg":
- sata: For SATA devices
- pcie: For PCIe devices
- - syscfg: To specify the syscfg based config register
Optional properties (port (child) node):
- st,sata-gen : Generation of locally attached SATA IP. Expected values
@@ -39,20 +40,20 @@
miphy365x_phy: miphy365x@fe382000 {
compatible = "st,miphy365x-phy";
- st,syscfg = <&syscfg_rear>;
+ st,syscfg = <&syscfg_rear 0x824 0x828>;
#address-cells = <1>;
#size-cells = <1>;
ranges;
phy_port0: port@fe382000 {
- reg = <0xfe382000 0x100>, <0xfe394000 0x100>, <0x824 0x4>;
- reg-names = "sata", "pcie", "syscfg";
+ reg = <0xfe382000 0x100>, <0xfe394000 0x100>;
+ reg-names = "sata", "pcie";
#phy-cells = <1>;
st,sata-gen = <3>;
};
phy_port1: port@fe38a000 {
- reg = <0xfe38a000 0x100>, <0xfe804000 0x100>, <0x828 0x4>;;
+ reg = <0xfe38a000 0x100>, <0xfe804000 0x100>;;
reg-names = "sata", "pcie", "syscfg";
#phy-cells = <1>;
st,pcie-tx-pol-inv;
diff --git a/Documentation/devicetree/bindings/phy/phy-stih407-usb.txt b/Documentation/devicetree/bindings/phy/phy-stih407-usb.txt
index 1ef8228..de6a706 100644
--- a/Documentation/devicetree/bindings/phy/phy-stih407-usb.txt
+++ b/Documentation/devicetree/bindings/phy/phy-stih407-usb.txt
@@ -5,10 +5,7 @@
Required properties:
- compatible : should be "st,stih407-usb2-phy"
-- reg : contain the offset and length of the system configuration registers
- used as glue logic to control & parameter phy
-- reg-names : the names of the system configuration registers in "reg", should be "param" and "reg"
-- st,syscfg : sysconfig register to manage phy parameter at driver level
+- st,syscfg : phandle of sysconfig bank plus integer array containing phyparam and phyctrl register offsets
- resets : list of phandle and reset specifier pairs. There should be two entries, one
for the whole phy and one for the port
- reset-names : list of reset signal names. Should be "global" and "port"
@@ -19,11 +16,8 @@
usb2_picophy0: usbpicophy@f8 {
compatible = "st,stih407-usb2-phy";
- reg = <0xf8 0x04>, /* syscfg 5062 */
- <0xf4 0x04>; /* syscfg 5061 */
- reg-names = "param", "ctrl";
#phy-cells = <0>;
- st,syscfg = <&syscfg_core>;
+ st,syscfg = <&syscfg_core 0x100 0xf4>;
resets = <&softreset STIH407_PICOPHY_SOFTRESET>,
<&picophyreset STIH407_PICOPHY0_RESET>;
reset-names = "global", "port";
diff --git a/Documentation/devicetree/bindings/phy/rockchip-usb-phy.txt b/Documentation/devicetree/bindings/phy/rockchip-usb-phy.txt
new file mode 100644
index 0000000..826454a
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/rockchip-usb-phy.txt
@@ -0,0 +1,37 @@
+ROCKCHIP USB2 PHY
+
+Required properties:
+ - compatible: rockchip,rk3288-usb-phy
+ - rockchip,grf : phandle to the syscon managing the "general
+ register files"
+ - #address-cells: should be 1
+ - #size-cells: should be 0
+
+Sub-nodes:
+Each PHY should be represented as a sub-node.
+
+Sub-nodes
+required properties:
+- #phy-cells: should be 0
+- reg: PHY configure reg address offset in GRF
+ "0x320" - for PHY attach to OTG controller
+ "0x334" - for PHY attach to HOST0 controller
+ "0x348" - for PHY attach to HOST1 controller
+
+Optional Properties:
+- clocks : phandle + clock specifier for the phy clocks
+- clock-names: string, clock name, must be "phyclk"
+
+Example:
+
+usbphy: phy {
+ compatible = "rockchip,rk3288-usb-phy";
+ rockchip,grf = <&grf>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ usbphy0: usb-phy0 {
+ #phy-cells = <0>;
+ reg = <0x320>;
+ };
+};
diff --git a/Documentation/devicetree/bindings/phy/samsung-phy.txt b/Documentation/devicetree/bindings/phy/samsung-phy.txt
index d5bad92..91e38cf 100644
--- a/Documentation/devicetree/bindings/phy/samsung-phy.txt
+++ b/Documentation/devicetree/bindings/phy/samsung-phy.txt
@@ -3,8 +3,8 @@
Required properties:
- compatible : should be "samsung,s5pv210-mipi-video-phy";
-- reg : offset and length of the MIPI DPHY register set;
- #phy-cells : from the generic phy bindings, must be 1;
+- syscon - phandle to the PMU system controller;
For "samsung,s5pv210-mipi-video-phy" compatible PHYs the second cell in
the PHY specifier identifies the PHY and its meaning is as follows:
diff --git a/arch/arm/boot/dts/stih416.dtsi b/arch/arm/boot/dts/stih416.dtsi
index fad9073..85afe01 100644
--- a/arch/arm/boot/dts/stih416.dtsi
+++ b/arch/arm/boot/dts/stih416.dtsi
@@ -283,21 +283,21 @@
miphy365x_phy: phy@fe382000 {
compatible = "st,miphy365x-phy";
- st,syscfg = <&syscfg_rear>;
+ st,syscfg = <&syscfg_rear 0x824 0x828>;
#address-cells = <1>;
#size-cells = <1>;
ranges;
phy_port0: port@fe382000 {
#phy-cells = <1>;
- reg = <0xfe382000 0x100>, <0xfe394000 0x100>, <0x824 0x4>;
- reg-names = "sata", "pcie", "syscfg";
+ reg = <0xfe382000 0x100>, <0xfe394000 0x100>;
+ reg-names = "sata", "pcie";
};
phy_port1: port@fe38a000 {
#phy-cells = <1>;
- reg = <0xfe38a000 0x100>, <0xfe804000 0x100>, <0x828 0x4>;
- reg-names = "sata", "pcie", "syscfg";
+ reg = <0xfe38a000 0x100>, <0xfe804000 0x100>;
+ reg-names = "sata", "pcie";
};
};
diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
index ccad880..b24500a 100644
--- a/drivers/phy/Kconfig
+++ b/drivers/phy/Kconfig
@@ -239,6 +239,13 @@
depends on OF
select GENERIC_PHY
+config PHY_ROCKCHIP_USB
+ tristate "Rockchip USB2 PHY Driver"
+ depends on ARCH_ROCKCHIP && OF
+ select GENERIC_PHY
+ help
+ Enable this to support the Rockchip USB 2.0 PHY.
+
config PHY_ST_SPEAR1310_MIPHY
tristate "ST SPEAR1310-MIPHY driver"
select GENERIC_PHY
diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
index aa74f96..48bf5a1 100644
--- a/drivers/phy/Makefile
+++ b/drivers/phy/Makefile
@@ -28,6 +28,7 @@
phy-exynos-usb2-$(CONFIG_PHY_S5PV210_USB2) += phy-s5pv210-usb2.o
obj-$(CONFIG_PHY_EXYNOS5_USBDRD) += phy-exynos5-usbdrd.o
obj-$(CONFIG_PHY_QCOM_APQ8064_SATA) += phy-qcom-apq8064-sata.o
+obj-$(CONFIG_PHY_ROCKCHIP_USB) += phy-rockchip-usb.o
obj-$(CONFIG_PHY_QCOM_IPQ806X_SATA) += phy-qcom-ipq806x-sata.o
obj-$(CONFIG_PHY_ST_SPEAR1310_MIPHY) += phy-spear1310-miphy.o
obj-$(CONFIG_PHY_ST_SPEAR1340_MIPHY) += phy-spear1340-miphy.o
diff --git a/drivers/phy/phy-armada375-usb2.c b/drivers/phy/phy-armada375-usb2.c
index ac7d99d..7c99ca2 100644
--- a/drivers/phy/phy-armada375-usb2.c
+++ b/drivers/phy/phy-armada375-usb2.c
@@ -118,8 +118,8 @@
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
usb_cluster_base = devm_ioremap_resource(&pdev->dev, res);
- if (!usb_cluster_base)
- return -ENOMEM;
+ if (IS_ERR(usb_cluster_base))
+ return PTR_ERR(usb_cluster_base);
phy = devm_phy_create(dev, NULL, &armada375_usb_phy_ops);
if (IS_ERR(phy)) {
diff --git a/drivers/phy/phy-exynos-mipi-video.c b/drivers/phy/phy-exynos-mipi-video.c
index 943e0f8..f017b2f 100644
--- a/drivers/phy/phy-exynos-mipi-video.c
+++ b/drivers/phy/phy-exynos-mipi-video.c
@@ -12,19 +12,18 @@
#include <linux/err.h>
#include <linux/io.h>
#include <linux/kernel.h>
+#include <linux/mfd/syscon/exynos4-pmu.h>
#include <linux/module.h>
#include <linux/of.h>
#include <linux/of_address.h>
#include <linux/phy/phy.h>
#include <linux/platform_device.h>
+#include <linux/regmap.h>
#include <linux/spinlock.h>
+#include <linux/mfd/syscon.h>
-/* MIPI_PHYn_CONTROL register offset: n = 0..1 */
+/* MIPI_PHYn_CONTROL reg. offset (for base address from ioremap): n = 0..1 */
#define EXYNOS_MIPI_PHY_CONTROL(n) ((n) * 4)
-#define EXYNOS_MIPI_PHY_ENABLE (1 << 0)
-#define EXYNOS_MIPI_PHY_SRESETN (1 << 1)
-#define EXYNOS_MIPI_PHY_MRESETN (1 << 2)
-#define EXYNOS_MIPI_PHY_RESET_MASK (3 << 1)
enum exynos_mipi_phy_id {
EXYNOS_MIPI_PHY_ID_CSIS0,
@@ -38,43 +37,62 @@
((id) == EXYNOS_MIPI_PHY_ID_DSIM0 || (id) == EXYNOS_MIPI_PHY_ID_DSIM1)
struct exynos_mipi_video_phy {
- spinlock_t slock;
struct video_phy_desc {
struct phy *phy;
unsigned int index;
} phys[EXYNOS_MIPI_PHYS_NUM];
+ spinlock_t slock;
void __iomem *regs;
+ struct mutex mutex;
+ struct regmap *regmap;
};
static int __set_phy_state(struct exynos_mipi_video_phy *state,
enum exynos_mipi_phy_id id, unsigned int on)
{
+ const unsigned int offset = EXYNOS4_MIPI_PHY_CONTROL(id / 2);
void __iomem *addr;
- u32 reg, reset;
-
- addr = state->regs + EXYNOS_MIPI_PHY_CONTROL(id / 2);
+ u32 val, reset;
if (is_mipi_dsim_phy_id(id))
- reset = EXYNOS_MIPI_PHY_MRESETN;
+ reset = EXYNOS4_MIPI_PHY_MRESETN;
else
- reset = EXYNOS_MIPI_PHY_SRESETN;
+ reset = EXYNOS4_MIPI_PHY_SRESETN;
- spin_lock(&state->slock);
- reg = readl(addr);
- if (on)
- reg |= reset;
- else
- reg &= ~reset;
- writel(reg, addr);
+ if (state->regmap) {
+ mutex_lock(&state->mutex);
+ regmap_read(state->regmap, offset, &val);
+ if (on)
+ val |= reset;
+ else
+ val &= ~reset;
+ regmap_write(state->regmap, offset, val);
+ if (on)
+ val |= EXYNOS4_MIPI_PHY_ENABLE;
+ else if (!(val & EXYNOS4_MIPI_PHY_RESET_MASK))
+ val &= ~EXYNOS4_MIPI_PHY_ENABLE;
+ regmap_write(state->regmap, offset, val);
+ mutex_unlock(&state->mutex);
+ } else {
+ addr = state->regs + EXYNOS_MIPI_PHY_CONTROL(id / 2);
- /* Clear ENABLE bit only if MRESETN, SRESETN bits are not set. */
- if (on)
- reg |= EXYNOS_MIPI_PHY_ENABLE;
- else if (!(reg & EXYNOS_MIPI_PHY_RESET_MASK))
- reg &= ~EXYNOS_MIPI_PHY_ENABLE;
+ spin_lock(&state->slock);
+ val = readl(addr);
+ if (on)
+ val |= reset;
+ else
+ val &= ~reset;
+ writel(val, addr);
+ /* Clear ENABLE bit only if MRESETN, SRESETN bits are not set */
+ if (on)
+ val |= EXYNOS4_MIPI_PHY_ENABLE;
+ else if (!(val & EXYNOS4_MIPI_PHY_RESET_MASK))
+ val &= ~EXYNOS4_MIPI_PHY_ENABLE;
- writel(reg, addr);
- spin_unlock(&state->slock);
+ writel(val, addr);
+ spin_unlock(&state->slock);
+ }
+
return 0;
}
@@ -118,7 +136,6 @@
{
struct exynos_mipi_video_phy *state;
struct device *dev = &pdev->dev;
- struct resource *res;
struct phy_provider *phy_provider;
unsigned int i;
@@ -126,14 +143,22 @@
if (!state)
return -ENOMEM;
- res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ state->regmap = syscon_regmap_lookup_by_phandle(dev->of_node, "syscon");
+ if (IS_ERR(state->regmap)) {
+ struct resource *res;
- state->regs = devm_ioremap_resource(dev, res);
- if (IS_ERR(state->regs))
- return PTR_ERR(state->regs);
+ dev_info(dev, "regmap lookup failed: %ld\n",
+ PTR_ERR(state->regmap));
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ state->regs = devm_ioremap_resource(dev, res);
+ if (IS_ERR(state->regs))
+ return PTR_ERR(state->regs);
+ }
dev_set_drvdata(dev, state);
spin_lock_init(&state->slock);
+ mutex_init(&state->mutex);
for (i = 0; i < EXYNOS_MIPI_PHYS_NUM; i++) {
struct phy *phy = devm_phy_create(dev, NULL,
diff --git a/drivers/phy/phy-miphy28lp.c b/drivers/phy/phy-miphy28lp.c
index 27fa62c..9b2848e 100644
--- a/drivers/phy/phy-miphy28lp.c
+++ b/drivers/phy/phy-miphy28lp.c
@@ -194,6 +194,14 @@
#define MIPHY_SATA_BANK_NB 3
#define MIPHY_PCIE_BANK_NB 2
+enum {
+ SYSCFG_CTRL,
+ SYSCFG_STATUS,
+ SYSCFG_PCI,
+ SYSCFG_SATA,
+ SYSCFG_REG_MAX,
+};
+
struct miphy28lp_phy {
struct phy *phy;
struct miphy28lp_dev *phydev;
@@ -211,10 +219,7 @@
u32 sata_gen;
/* Sysconfig registers offsets needed to configure the device */
- u32 syscfg_miphy_ctrl;
- u32 syscfg_miphy_status;
- u32 syscfg_pci;
- u32 syscfg_sata;
+ u32 syscfg_reg[SYSCFG_REG_MAX];
u8 type;
};
@@ -834,12 +839,12 @@
if (!miphy_phy->osc_rdy)
return 0;
- if (!miphy_phy->syscfg_miphy_status)
+ if (!miphy_phy->syscfg_reg[SYSCFG_STATUS])
return -EINVAL;
do {
- regmap_read(miphy_dev->regmap, miphy_phy->syscfg_miphy_status,
- &val);
+ regmap_read(miphy_dev->regmap,
+ miphy_phy->syscfg_reg[SYSCFG_STATUS], &val);
if ((val & MIPHY_OSC_RDY) != MIPHY_OSC_RDY)
cpu_relax();
@@ -888,7 +893,7 @@
int err;
struct miphy28lp_dev *miphy_dev = miphy_phy->phydev;
- if (!miphy_phy->syscfg_miphy_ctrl)
+ if (!miphy_phy->syscfg_reg[SYSCFG_CTRL])
return -EINVAL;
err = reset_control_assert(miphy_phy->miphy_rst);
@@ -900,7 +905,8 @@
if (miphy_phy->osc_force_ext)
miphy_val |= MIPHY_OSC_FORCE_EXT;
- regmap_update_bits(miphy_dev->regmap, miphy_phy->syscfg_miphy_ctrl,
+ regmap_update_bits(miphy_dev->regmap,
+ miphy_phy->syscfg_reg[SYSCFG_CTRL],
MIPHY_CTRL_MASK, miphy_val);
err = reset_control_deassert(miphy_phy->miphy_rst);
@@ -917,8 +923,9 @@
struct miphy28lp_dev *miphy_dev = miphy_phy->phydev;
int err, sata_conf = SATA_CTRL_SELECT_SATA;
- if ((!miphy_phy->syscfg_sata) || (!miphy_phy->syscfg_pci)
- || (!miphy_phy->base))
+ if ((!miphy_phy->syscfg_reg[SYSCFG_SATA]) ||
+ (!miphy_phy->syscfg_reg[SYSCFG_PCI]) ||
+ (!miphy_phy->base))
return -EINVAL;
dev_info(miphy_dev->dev, "sata-up mode, addr 0x%p\n", miphy_phy->base);
@@ -926,10 +933,11 @@
/* Configure the glue-logic */
sata_conf |= ((miphy_phy->sata_gen - SATA_GEN1) << SATA_SPDMODE);
- regmap_update_bits(miphy_dev->regmap, miphy_phy->syscfg_sata,
+ regmap_update_bits(miphy_dev->regmap,
+ miphy_phy->syscfg_reg[SYSCFG_SATA],
SATA_CTRL_MASK, sata_conf);
- regmap_update_bits(miphy_dev->regmap, miphy_phy->syscfg_pci,
+ regmap_update_bits(miphy_dev->regmap, miphy_phy->syscfg_reg[SYSCFG_PCI],
PCIE_CTRL_MASK, SATA_CTRL_SELECT_PCIE);
/* MiPHY path and clocking init */
@@ -951,17 +959,19 @@
struct miphy28lp_dev *miphy_dev = miphy_phy->phydev;
int err;
- if ((!miphy_phy->syscfg_sata) || (!miphy_phy->syscfg_pci)
+ if ((!miphy_phy->syscfg_reg[SYSCFG_SATA]) ||
+ (!miphy_phy->syscfg_reg[SYSCFG_PCI])
|| (!miphy_phy->base) || (!miphy_phy->pipebase))
return -EINVAL;
dev_info(miphy_dev->dev, "pcie-up mode, addr 0x%p\n", miphy_phy->base);
/* Configure the glue-logic */
- regmap_update_bits(miphy_dev->regmap, miphy_phy->syscfg_sata,
+ regmap_update_bits(miphy_dev->regmap,
+ miphy_phy->syscfg_reg[SYSCFG_SATA],
SATA_CTRL_MASK, SATA_CTRL_SELECT_PCIE);
- regmap_update_bits(miphy_dev->regmap, miphy_phy->syscfg_pci,
+ regmap_update_bits(miphy_dev->regmap, miphy_phy->syscfg_reg[SYSCFG_PCI],
PCIE_CTRL_MASK, SYSCFG_PCIE_PCIE_VAL);
/* MiPHY path and clocking init */
@@ -1156,7 +1166,8 @@
static int miphy28lp_of_probe(struct device_node *np,
struct miphy28lp_phy *miphy_phy)
{
- struct resource res;
+ int i;
+ u32 ctrlreg;
miphy_phy->osc_force_ext =
of_property_read_bool(np, "st,osc-force-ext");
@@ -1175,18 +1186,10 @@
if (!miphy_phy->sata_gen)
miphy_phy->sata_gen = SATA_GEN1;
- if (!miphy28lp_get_resource_byname(np, "miphy-ctrl-glue", &res))
- miphy_phy->syscfg_miphy_ctrl = res.start;
-
- if (!miphy28lp_get_resource_byname(np, "miphy-status-glue", &res))
- miphy_phy->syscfg_miphy_status = res.start;
-
- if (!miphy28lp_get_resource_byname(np, "pcie-glue", &res))
- miphy_phy->syscfg_pci = res.start;
-
- if (!miphy28lp_get_resource_byname(np, "sata-glue", &res))
- miphy_phy->syscfg_sata = res.start;
-
+ for (i = 0; i < SYSCFG_REG_MAX; i++) {
+ if (!of_property_read_u32_index(np, "st,syscfg", i, &ctrlreg))
+ miphy_phy->syscfg_reg[i] = ctrlreg;
+ }
return 0;
}
diff --git a/drivers/phy/phy-miphy365x.c b/drivers/phy/phy-miphy365x.c
index 6ab43a8..6c80154 100644
--- a/drivers/phy/phy-miphy365x.c
+++ b/drivers/phy/phy-miphy365x.c
@@ -141,7 +141,7 @@
bool pcie_tx_pol_inv;
bool sata_tx_pol_inv;
u32 sata_gen;
- u64 ctrlreg;
+ u32 ctrlreg;
u8 type;
};
@@ -179,7 +179,7 @@
bool sata = (miphy_phy->type == MIPHY_TYPE_SATA);
return regmap_update_bits(miphy_dev->regmap,
- (unsigned int)miphy_phy->ctrlreg,
+ miphy_phy->ctrlreg,
SYSCFG_SELECT_SATA_MASK,
sata << SYSCFG_SELECT_SATA_POS);
}
@@ -445,7 +445,6 @@
{
struct device_node *phynode = miphy_phy->phy->dev.of_node;
const char *name;
- const __be32 *taddr;
int type = miphy_phy->type;
int ret;
@@ -455,22 +454,6 @@
return ret;
}
- if (!strncmp(name, "syscfg", 6)) {
- taddr = of_get_address(phynode, index, NULL, NULL);
- if (!taddr) {
- dev_err(dev, "failed to fetch syscfg address\n");
- return -EINVAL;
- }
-
- miphy_phy->ctrlreg = of_translate_address(phynode, taddr);
- if (miphy_phy->ctrlreg == OF_BAD_ADDR) {
- dev_err(dev, "failed to translate syscfg address\n");
- return -EINVAL;
- }
-
- return 0;
- }
-
if (!((!strncmp(name, "sata", 4) && type == MIPHY_TYPE_SATA) ||
(!strncmp(name, "pcie", 4) && type == MIPHY_TYPE_PCIE)))
return 0;
@@ -606,7 +589,15 @@
return ret;
phy_set_drvdata(phy, miphy_dev->phys[port]);
+
port++;
+ /* sysconfig offsets are indexed from 1 */
+ ret = of_property_read_u32_index(np, "st,syscfg", port,
+ &miphy_phy->ctrlreg);
+ if (ret) {
+ dev_err(&pdev->dev, "No sysconfig offset found\n");
+ return ret;
+ }
}
provider = devm_of_phy_provider_register(&pdev->dev, miphy365x_xlate);
diff --git a/drivers/phy/phy-rockchip-usb.c b/drivers/phy/phy-rockchip-usb.c
new file mode 100644
index 0000000..22011c3
--- /dev/null
+++ b/drivers/phy/phy-rockchip-usb.c
@@ -0,0 +1,158 @@
+/*
+ * Rockchip usb PHY driver
+ *
+ * Copyright (C) 2014 Yunzhi Li <lyz@rock-chips.com>
+ * Copyright (C) 2014 ROCKCHIP, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/consumer.h>
+#include <linux/reset.h>
+#include <linux/regmap.h>
+#include <linux/mfd/syscon.h>
+
+/*
+ * The higher 16-bit of this register is used for write protection
+ * only if BIT(13 + 16) set to 1 the BIT(13) can be written.
+ */
+#define SIDDQ_WRITE_ENA BIT(29)
+#define SIDDQ_ON BIT(13)
+#define SIDDQ_OFF (0 << 13)
+
+struct rockchip_usb_phy {
+ unsigned int reg_offset;
+ struct regmap *reg_base;
+ struct clk *clk;
+ struct phy *phy;
+};
+
+static int rockchip_usb_phy_power(struct rockchip_usb_phy *phy,
+ bool siddq)
+{
+ return regmap_write(phy->reg_base, phy->reg_offset,
+ SIDDQ_WRITE_ENA | (siddq ? SIDDQ_ON : SIDDQ_OFF));
+}
+
+static int rockchip_usb_phy_power_off(struct phy *_phy)
+{
+ struct rockchip_usb_phy *phy = phy_get_drvdata(_phy);
+ int ret = 0;
+
+ /* Power down usb phy analog blocks by set siddq 1 */
+ ret = rockchip_usb_phy_power(phy, 1);
+ if (ret)
+ return ret;
+
+ clk_disable_unprepare(phy->clk);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static int rockchip_usb_phy_power_on(struct phy *_phy)
+{
+ struct rockchip_usb_phy *phy = phy_get_drvdata(_phy);
+ int ret = 0;
+
+ ret = clk_prepare_enable(phy->clk);
+ if (ret)
+ return ret;
+
+ /* Power up usb phy analog blocks by set siddq 0 */
+ ret = rockchip_usb_phy_power(phy, 0);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static struct phy_ops ops = {
+ .power_on = rockchip_usb_phy_power_on,
+ .power_off = rockchip_usb_phy_power_off,
+ .owner = THIS_MODULE,
+};
+
+static int rockchip_usb_phy_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct rockchip_usb_phy *rk_phy;
+ struct phy_provider *phy_provider;
+ struct device_node *child;
+ struct regmap *grf;
+ unsigned int reg_offset;
+
+ grf = syscon_regmap_lookup_by_phandle(dev->of_node, "rockchip,grf");
+ if (IS_ERR(grf)) {
+ dev_err(&pdev->dev, "Missing rockchip,grf property\n");
+ return PTR_ERR(grf);
+ }
+
+ for_each_available_child_of_node(dev->of_node, child) {
+ rk_phy = devm_kzalloc(dev, sizeof(*rk_phy), GFP_KERNEL);
+ if (!rk_phy)
+ return -ENOMEM;
+
+ if (of_property_read_u32(child, "reg", ®_offset)) {
+ dev_err(dev, "missing reg property in node %s\n",
+ child->name);
+ return -EINVAL;
+ }
+
+ rk_phy->reg_offset = reg_offset;
+ rk_phy->reg_base = grf;
+
+ rk_phy->clk = of_clk_get_by_name(child, "phyclk");
+ if (IS_ERR(rk_phy->clk))
+ rk_phy->clk = NULL;
+
+ rk_phy->phy = devm_phy_create(dev, child, &ops);
+ if (IS_ERR(rk_phy->phy)) {
+ dev_err(dev, "failed to create PHY\n");
+ return PTR_ERR(rk_phy->phy);
+ }
+ phy_set_drvdata(rk_phy->phy, rk_phy);
+ }
+
+ phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+ return PTR_ERR_OR_ZERO(phy_provider);
+}
+
+static const struct of_device_id rockchip_usb_phy_dt_ids[] = {
+ { .compatible = "rockchip,rk3288-usb-phy" },
+ {}
+};
+
+MODULE_DEVICE_TABLE(of, rockchip_usb_phy_dt_ids);
+
+static struct platform_driver rockchip_usb_driver = {
+ .probe = rockchip_usb_phy_probe,
+ .driver = {
+ .name = "rockchip-usb-phy",
+ .owner = THIS_MODULE,
+ .of_match_table = rockchip_usb_phy_dt_ids,
+ },
+};
+
+module_platform_driver(rockchip_usb_driver);
+
+MODULE_AUTHOR("Yunzhi Li <lyz@rock-chips.com>");
+MODULE_DESCRIPTION("Rockchip USB 2.0 PHY driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/phy/phy-stih407-usb.c b/drivers/phy/phy-stih407-usb.c
index 74f0fab..1d5ae5f 100644
--- a/drivers/phy/phy-stih407-usb.c
+++ b/drivers/phy/phy-stih407-usb.c
@@ -22,6 +22,9 @@
#include <linux/mfd/syscon.h>
#include <linux/phy/phy.h>
+#define PHYPARAM_REG 1
+#define PHYCTRL_REG 2
+
/* Default PHY_SEL and REFCLKSEL configuration */
#define STIH407_USB_PICOPHY_CTRL_PORT_CONF 0x6
#define STIH407_USB_PICOPHY_CTRL_PORT_MASK 0x1f
@@ -93,7 +96,7 @@
struct device_node *np = dev->of_node;
struct phy_provider *phy_provider;
struct phy *phy;
- struct resource *res;
+ int ret;
phy_dev = devm_kzalloc(dev, sizeof(*phy_dev), GFP_KERNEL);
if (!phy_dev)
@@ -123,19 +126,19 @@
return PTR_ERR(phy_dev->regmap);
}
- res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "ctrl");
- if (!res) {
- dev_err(dev, "No ctrl reg found\n");
- return -ENXIO;
+ ret = of_property_read_u32_index(np, "st,syscfg", PHYPARAM_REG,
+ &phy_dev->param);
+ if (ret) {
+ dev_err(dev, "can't get phyparam offset (%d)\n", ret);
+ return ret;
}
- phy_dev->ctrl = res->start;
- res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "param");
- if (!res) {
- dev_err(dev, "No param reg found\n");
- return -ENXIO;
+ ret = of_property_read_u32_index(np, "st,syscfg", PHYCTRL_REG,
+ &phy_dev->ctrl);
+ if (ret) {
+ dev_err(dev, "can't get phyctrl offset (%d)\n", ret);
+ return ret;
}
- phy_dev->param = res->start;
phy = devm_phy_create(dev, NULL, &stih407_usb2_picophy_data);
if (IS_ERR(phy)) {
diff --git a/drivers/phy/phy-ti-pipe3.c b/drivers/phy/phy-ti-pipe3.c
index 465de2c..95c88f9 100644
--- a/drivers/phy/phy-ti-pipe3.c
+++ b/drivers/phy/phy-ti-pipe3.c
@@ -28,6 +28,7 @@
#include <linux/delay.h>
#include <linux/phy/omap_control_phy.h>
#include <linux/of_platform.h>
+#include <linux/spinlock.h>
#define PLL_STATUS 0x00000004
#define PLL_GO 0x00000008
@@ -82,6 +83,10 @@
struct clk *refclk;
struct clk *div_clk;
struct pipe3_dpll_map *dpll_map;
+ bool enabled;
+ spinlock_t lock; /* serialize clock enable/disable */
+ /* the below flag is needed specifically for SATA */
+ bool refclk_enabled;
};
static struct pipe3_dpll_map dpll_map_usb[] = {
@@ -307,6 +312,7 @@
return -ENOMEM;
phy->dev = &pdev->dev;
+ spin_lock_init(&phy->lock);
if (!of_device_is_compatible(node, "ti,phy-pipe3-pcie")) {
match = of_match_device(of_match_ptr(ti_pipe3_id_table),
@@ -333,21 +339,24 @@
}
}
+ phy->refclk = devm_clk_get(phy->dev, "refclk");
+ if (IS_ERR(phy->refclk)) {
+ dev_err(&pdev->dev, "unable to get refclk\n");
+ /* older DTBs have missing refclk in SATA PHY
+ * so don't bail out in case of SATA PHY.
+ */
+ if (!of_device_is_compatible(node, "ti,phy-pipe3-sata"))
+ return PTR_ERR(phy->refclk);
+ }
+
if (!of_device_is_compatible(node, "ti,phy-pipe3-sata")) {
phy->wkupclk = devm_clk_get(phy->dev, "wkupclk");
if (IS_ERR(phy->wkupclk)) {
dev_err(&pdev->dev, "unable to get wkupclk\n");
return PTR_ERR(phy->wkupclk);
}
-
- phy->refclk = devm_clk_get(phy->dev, "refclk");
- if (IS_ERR(phy->refclk)) {
- dev_err(&pdev->dev, "unable to get refclk\n");
- return PTR_ERR(phy->refclk);
- }
} else {
phy->wkupclk = ERR_PTR(-ENODEV);
- phy->refclk = ERR_PTR(-ENODEV);
}
if (of_device_is_compatible(node, "ti,phy-pipe3-pcie")) {
@@ -426,33 +435,42 @@
}
#ifdef CONFIG_PM
-
-static int ti_pipe3_runtime_suspend(struct device *dev)
+static int ti_pipe3_enable_refclk(struct ti_pipe3 *phy)
{
- struct ti_pipe3 *phy = dev_get_drvdata(dev);
+ if (!IS_ERR(phy->refclk) && !phy->refclk_enabled) {
+ int ret;
- if (!IS_ERR(phy->wkupclk))
- clk_disable_unprepare(phy->wkupclk);
- if (!IS_ERR(phy->refclk))
- clk_disable_unprepare(phy->refclk);
- if (!IS_ERR(phy->div_clk))
- clk_disable_unprepare(phy->div_clk);
+ ret = clk_prepare_enable(phy->refclk);
+ if (ret) {
+ dev_err(phy->dev, "Failed to enable refclk %d\n", ret);
+ return ret;
+ }
+ phy->refclk_enabled = true;
+ }
return 0;
}
-static int ti_pipe3_runtime_resume(struct device *dev)
+static void ti_pipe3_disable_refclk(struct ti_pipe3 *phy)
{
- u32 ret = 0;
- struct ti_pipe3 *phy = dev_get_drvdata(dev);
+ if (!IS_ERR(phy->refclk))
+ clk_disable_unprepare(phy->refclk);
- if (!IS_ERR(phy->refclk)) {
- ret = clk_prepare_enable(phy->refclk);
- if (ret) {
- dev_err(phy->dev, "Failed to enable refclk %d\n", ret);
- goto err1;
- }
- }
+ phy->refclk_enabled = false;
+}
+
+static int ti_pipe3_enable_clocks(struct ti_pipe3 *phy)
+{
+ int ret = 0;
+ unsigned long flags;
+
+ spin_lock_irqsave(&phy->lock, flags);
+ if (phy->enabled)
+ goto err1;
+
+ ret = ti_pipe3_enable_refclk(phy);
+ if (ret)
+ goto err1;
if (!IS_ERR(phy->wkupclk)) {
ret = clk_prepare_enable(phy->wkupclk);
@@ -469,6 +487,9 @@
goto err3;
}
}
+
+ phy->enabled = true;
+ spin_unlock_irqrestore(&phy->lock, flags);
return 0;
err3:
@@ -479,20 +500,80 @@
if (!IS_ERR(phy->refclk))
clk_disable_unprepare(phy->refclk);
+ ti_pipe3_disable_refclk(phy);
err1:
+ spin_unlock_irqrestore(&phy->lock, flags);
return ret;
}
+static void ti_pipe3_disable_clocks(struct ti_pipe3 *phy)
+{
+ unsigned long flags;
+
+ spin_lock_irqsave(&phy->lock, flags);
+ if (!phy->enabled) {
+ spin_unlock_irqrestore(&phy->lock, flags);
+ return;
+ }
+
+ if (!IS_ERR(phy->wkupclk))
+ clk_disable_unprepare(phy->wkupclk);
+ /* Don't disable refclk for SATA PHY due to Errata i783 */
+ if (!of_device_is_compatible(phy->dev->of_node, "ti,phy-pipe3-sata"))
+ ti_pipe3_disable_refclk(phy);
+ if (!IS_ERR(phy->div_clk))
+ clk_disable_unprepare(phy->div_clk);
+ phy->enabled = false;
+ spin_unlock_irqrestore(&phy->lock, flags);
+}
+
+static int ti_pipe3_runtime_suspend(struct device *dev)
+{
+ struct ti_pipe3 *phy = dev_get_drvdata(dev);
+
+ ti_pipe3_disable_clocks(phy);
+ return 0;
+}
+
+static int ti_pipe3_runtime_resume(struct device *dev)
+{
+ struct ti_pipe3 *phy = dev_get_drvdata(dev);
+ int ret = 0;
+
+ ret = ti_pipe3_enable_clocks(phy);
+ return ret;
+}
+
+static int ti_pipe3_suspend(struct device *dev)
+{
+ struct ti_pipe3 *phy = dev_get_drvdata(dev);
+
+ ti_pipe3_disable_clocks(phy);
+ return 0;
+}
+
+static int ti_pipe3_resume(struct device *dev)
+{
+ struct ti_pipe3 *phy = dev_get_drvdata(dev);
+ int ret;
+
+ ret = ti_pipe3_enable_clocks(phy);
+ if (ret)
+ return ret;
+
+ pm_runtime_disable(dev);
+ pm_runtime_set_active(dev);
+ pm_runtime_enable(dev);
+ return 0;
+}
+#endif
+
static const struct dev_pm_ops ti_pipe3_pm_ops = {
SET_RUNTIME_PM_OPS(ti_pipe3_runtime_suspend,
ti_pipe3_runtime_resume, NULL)
+ SET_SYSTEM_SLEEP_PM_OPS(ti_pipe3_suspend, ti_pipe3_resume)
};
-#define DEV_PM_OPS (&ti_pipe3_pm_ops)
-#else
-#define DEV_PM_OPS NULL
-#endif
-
#ifdef CONFIG_OF
static const struct of_device_id ti_pipe3_id_table[] = {
{
@@ -520,7 +601,7 @@
.remove = ti_pipe3_remove,
.driver = {
.name = "ti-pipe3",
- .pm = DEV_PM_OPS,
+ .pm = &ti_pipe3_pm_ops,
.of_match_table = of_match_ptr(ti_pipe3_id_table),
},
};
diff --git a/include/linux/mfd/syscon/exynos4-pmu.h b/include/linux/mfd/syscon/exynos4-pmu.h
new file mode 100644
index 0000000..278b1b1
--- /dev/null
+++ b/include/linux/mfd/syscon/exynos4-pmu.h
@@ -0,0 +1,21 @@
+/*
+ * Copyright (C) 2015 Samsung Electronics Co., Ltd.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef _LINUX_MFD_SYSCON_PMU_EXYNOS4_H_
+#define _LINUX_MFD_SYSCON_PMU_EXYNOS4_H_
+
+/* Exynos4 PMU register definitions */
+
+/* MIPI_PHYn_CONTROL register offset: n = 0..1 */
+#define EXYNOS4_MIPI_PHY_CONTROL(n) (0x710 + (n) * 4)
+#define EXYNOS4_MIPI_PHY_ENABLE (1 << 0)
+#define EXYNOS4_MIPI_PHY_SRESETN (1 << 1)
+#define EXYNOS4_MIPI_PHY_MRESETN (1 << 2)
+#define EXYNOS4_MIPI_PHY_RESET_MASK (3 << 1)
+
+#endif /* _LINUX_MFD_SYSCON_PMU_EXYNOS4_H_ */