mx3fb: support pan display with fb_set_var
Users may call FBIOPUT_VSCREENINFO ioctrl to do pan display.
This ioctrl relies on fb_set_var() to do the job. fb_set_var()
calls the custom fb_set_par() method and then calls the custom
fb_pan_display() method. Before calling the custom fb_pan_display()
method, info->var is already updated from the new *var in fb_set_var().
And, the custom fb_pan_display() method checks if xoffset and yoffset
in info->var and the new *var are different before doing actual panning,
which prevents the panning from happening within fb_set_var() context.
This patch caches the current var info locally in mx3fb driver so that
pan display with fb_set_var is supported.
Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
diff --git a/drivers/video/mx3fb.c b/drivers/video/mx3fb.c
index eec0d7b..da1d052 100644
--- a/drivers/video/mx3fb.c
+++ b/drivers/video/mx3fb.c
@@ -269,7 +269,7 @@
dma_cookie_t cookie;
struct scatterlist sg[2];
- u32 sync; /* preserve var->sync flags */
+ struct fb_var_screeninfo cur_var; /* current var info */
};
static void mx3fb_dma_done(void *);
@@ -700,7 +700,7 @@
static int __set_par(struct fb_info *fbi, bool lock)
{
- u32 mem_len;
+ u32 mem_len, cur_xoffset, cur_yoffset;
struct ipu_di_signal_cfg sig_cfg;
enum ipu_panel mode = IPU_PANEL_TFT;
struct mx3fb_info *mx3_fbi = fbi->par;
@@ -780,8 +780,25 @@
video->out_height = fbi->var.yres;
video->out_stride = fbi->var.xres_virtual;
- if (mx3_fbi->blank == FB_BLANK_UNBLANK)
+ if (mx3_fbi->blank == FB_BLANK_UNBLANK) {
sdc_enable_channel(mx3_fbi);
+ /*
+ * sg[0] points to fb smem_start address
+ * and is actually active in controller.
+ */
+ mx3_fbi->cur_var.xoffset = 0;
+ mx3_fbi->cur_var.yoffset = 0;
+ }
+
+ /*
+ * Preserve xoffset and yoffest in case they are
+ * inactive in controller as fb is blanked.
+ */
+ cur_xoffset = mx3_fbi->cur_var.xoffset;
+ cur_yoffset = mx3_fbi->cur_var.yoffset;
+ mx3_fbi->cur_var = fbi->var;
+ mx3_fbi->cur_var.xoffset = cur_xoffset;
+ mx3_fbi->cur_var.yoffset = cur_yoffset;
return 0;
}
@@ -901,8 +918,8 @@
var->grayscale = 0;
/* Preserve sync flags */
- var->sync |= mx3_fbi->sync;
- mx3_fbi->sync |= var->sync;
+ var->sync |= mx3_fbi->cur_var.sync;
+ mx3_fbi->cur_var.sync |= var->sync;
return 0;
}
@@ -1043,8 +1060,8 @@
return -EINVAL;
}
- if (fbi->var.xoffset == var->xoffset &&
- fbi->var.yoffset == var->yoffset)
+ if (mx3_fbi->cur_var.xoffset == var->xoffset &&
+ mx3_fbi->cur_var.yoffset == var->yoffset)
return 0; /* No change, do nothing */
y_bottom = var->yoffset;
@@ -1127,6 +1144,8 @@
else
fbi->var.vmode &= ~FB_VMODE_YWRAP;
+ mx3_fbi->cur_var = fbi->var;
+
mutex_unlock(&mx3_fbi->mutex);
dev_dbg(fbi->device, "Update complete\n");