ARM: dts: add cubietech cubieboard4

Add a Cubietech Cubieboard4 device tree and instruct make to build it. This
device tree has been derived from the sun9i-a80-optimus.dts as they are very
similar in design[1]. Notably, I2C3 is not used on Cubieboard4 and the LED/PWM
definitions will need to be updated in the future.

[1] http://dl.cubieboard.org/model/cc-a80/Hardware/CC-A80-HW-V1.1.pdf

Signed-off-by: Tyler Baker <tyler.baker@linaro.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 92b3c85..c6e95ab 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -569,7 +569,8 @@
 	sun8i-a23-ippo-q8h-v5.dtb \
 	sun8i-a23-ippo-q8h-v1.2.dtb
 dtb-$(CONFIG_MACH_SUN9I) += \
-	sun9i-a80-optimus.dtb
+	sun9i-a80-optimus.dtb \
+	sun9i-a80-cubieboard4.dtb
 dtb-$(CONFIG_ARCH_TEGRA_2x_SOC) += \
 	tegra20-harmony.dtb \
 	tegra20-iris-512.dtb \
diff --git a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts b/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts
new file mode 100644
index 0000000..6484dcf
--- /dev/null
+++ b/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts
@@ -0,0 +1,99 @@
+/*
+ * Copyright 2015 Tyler Baker
+ *
+ * Tyler Baker <tyler.baker@linaro.org>
+ * Chen-Yu Tsai <wens@csie.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun9i-a80.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+	model = "Cubietech Cubieboard4";
+	compatible = "cubietech,a80-cubieboard4", "allwinner,sun9i-a80";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+};
+
+&pio {
+	mmc0_cd_pin_cubieboard4: mmc0_cd_pin@0 {
+		allwinner,pins = "PH18";
+		allwinner,function = "gpio_in";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+	};
+};
+
+&mmc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins>, <&mmc0_cd_pin_cubieboard4>;
+	vmmc-supply = <&reg_vcc3v0>;
+	bus-width = <4>;
+	cd-gpios = <&pio 7 18 GPIO_ACTIVE_HIGH>; /* PH18 */
+	cd-inverted;
+	status = "okay";
+};
+
+&mmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_8bit_pins>;
+	vmmc-supply = <&reg_vcc3v0>;
+	bus-width = <8>;
+	non-removable;
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins_a>;
+	status = "okay";
+};