| /* Copyright (c) 2016-2017 The Linux Foundation. All rights reserved. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 and |
| * only version 2 as published by the Free Software Foundation. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| */ |
| |
| #define pr_fmt(fmt) "SMB138X: %s: " fmt, __func__ |
| |
| #include <linux/device.h> |
| #include <linux/iio/consumer.h> |
| #include <linux/module.h> |
| #include <linux/of.h> |
| #include <linux/of_device.h> |
| #include <linux/of_irq.h> |
| #include <linux/platform_device.h> |
| #include <linux/power_supply.h> |
| #include <linux/regmap.h> |
| #include <linux/regulator/driver.h> |
| #include <linux/regulator/machine.h> |
| #include <linux/regulator/of_regulator.h> |
| #include <linux/qpnp/qpnp-revid.h> |
| #include "smb-reg.h" |
| #include "smb-lib.h" |
| #include "storm-watch.h" |
| #include <linux/pmic-voter.h> |
| |
| #define SMB138X_DEFAULT_FCC_UA 1000000 |
| #define SMB138X_DEFAULT_ICL_UA 1500000 |
| |
| /* Registers that are not common to be mentioned in smb-reg.h */ |
| #define SMB2CHG_MISC_ENG_SDCDC_CFG2 (MISC_BASE + 0xC1) |
| #define ENG_SDCDC_SEL_OOB_VTH_BIT BIT(0) |
| |
| #define SMB2CHG_MISC_ENG_SDCDC_CFG6 (MISC_BASE + 0xC5) |
| #define DEAD_TIME_MASK GENMASK(7, 4) |
| #define HIGH_DEAD_TIME_MASK GENMASK(7, 4) |
| |
| #define SMB2CHG_DC_TM_SREFGEN (DCIN_BASE + 0xE2) |
| #define STACKED_DIODE_EN_BIT BIT(2) |
| |
| #define TDIE_AVG_COUNT 10 |
| #define MAX_SPEED_READING_TIMES 5 |
| |
| enum { |
| OOB_COMP_WA_BIT = BIT(0), |
| }; |
| |
| static struct smb_params v1_params = { |
| .fcc = { |
| .name = "fast charge current", |
| .reg = FAST_CHARGE_CURRENT_CFG_REG, |
| .min_u = 0, |
| .max_u = 6000000, |
| .step_u = 25000, |
| }, |
| .fv = { |
| .name = "float voltage", |
| .reg = FLOAT_VOLTAGE_CFG_REG, |
| .min_u = 2450000, |
| .max_u = 4950000, |
| .step_u = 10000, |
| }, |
| .usb_icl = { |
| .name = "usb input current limit", |
| .reg = USBIN_CURRENT_LIMIT_CFG_REG, |
| .min_u = 0, |
| .max_u = 6000000, |
| .step_u = 25000, |
| }, |
| .dc_icl = { |
| .name = "dc input current limit", |
| .reg = DCIN_CURRENT_LIMIT_CFG_REG, |
| .min_u = 0, |
| .max_u = 6000000, |
| .step_u = 25000, |
| }, |
| .freq_buck = { |
| .name = "buck switching frequency", |
| .reg = CFG_BUCKBOOST_FREQ_SELECT_BUCK_REG, |
| .min_u = 500, |
| .max_u = 2000, |
| .step_u = 100, |
| }, |
| }; |
| |
| struct smb_dt_props { |
| bool suspend_input; |
| int fcc_ua; |
| int usb_icl_ua; |
| int dc_icl_ua; |
| int chg_temp_max_mdegc; |
| int connector_temp_max_mdegc; |
| int pl_mode; |
| }; |
| |
| struct smb138x { |
| struct smb_charger chg; |
| struct smb_dt_props dt; |
| struct power_supply *parallel_psy; |
| u32 wa_flags; |
| struct pmic_revid_data *pmic_rev_id; |
| char *name; |
| }; |
| |
| static int __debug_mask; |
| module_param_named( |
| debug_mask, __debug_mask, int, 0600 |
| ); |
| |
| irqreturn_t smb138x_handle_slave_chg_state_change(int irq, void *data) |
| { |
| struct smb_irq_data *irq_data = data; |
| struct smb138x *chip = irq_data->parent_data; |
| |
| if (chip->parallel_psy) |
| power_supply_changed(chip->parallel_psy); |
| |
| return IRQ_HANDLED; |
| } |
| |
| static int smb138x_get_prop_charger_temp(struct smb138x *chip, |
| union power_supply_propval *val) |
| { |
| union power_supply_propval pval; |
| int rc = 0, avg = 0, i; |
| struct smb_charger *chg = &chip->chg; |
| int die_avg_count; |
| |
| if (chg->temp_speed_reading_count < MAX_SPEED_READING_TIMES) { |
| chg->temp_speed_reading_count++; |
| die_avg_count = 1; |
| } else { |
| die_avg_count = TDIE_AVG_COUNT; |
| } |
| |
| for (i = 0; i < die_avg_count; i++) { |
| pval.intval = 0; |
| rc = smblib_get_prop_charger_temp(chg, &pval); |
| if (rc < 0) { |
| pr_err("Couldnt read chg temp at %dth iteration rc = %d\n", |
| i + 1, rc); |
| return rc; |
| } |
| avg += pval.intval; |
| } |
| val->intval = avg / die_avg_count; |
| return rc; |
| } |
| |
| static int smb138x_parse_dt(struct smb138x *chip) |
| { |
| struct smb_charger *chg = &chip->chg; |
| struct device_node *node = chg->dev->of_node; |
| int rc; |
| |
| if (!node) { |
| pr_err("device tree node missing\n"); |
| return -EINVAL; |
| } |
| |
| rc = of_property_read_u32(node, |
| "qcom,parallel-mode", &chip->dt.pl_mode); |
| if (rc < 0) |
| chip->dt.pl_mode = POWER_SUPPLY_PL_USBMID_USBMID; |
| |
| /* check that smb1355 is configured to run in mid-mid mode */ |
| if (chip->pmic_rev_id->pmic_subtype == SMB1355_SUBTYPE |
| && chip->dt.pl_mode != POWER_SUPPLY_PL_USBMID_USBMID) { |
| pr_err("Smb1355 can only run in MID-MID mode, saw = %d mode\n", |
| chip->dt.pl_mode); |
| return -EINVAL; |
| } |
| |
| chip->dt.suspend_input = of_property_read_bool(node, |
| "qcom,suspend-input"); |
| |
| rc = of_property_read_u32(node, |
| "qcom,fcc-max-ua", &chip->dt.fcc_ua); |
| if (rc < 0) |
| chip->dt.fcc_ua = SMB138X_DEFAULT_FCC_UA; |
| |
| rc = of_property_read_u32(node, |
| "qcom,usb-icl-ua", &chip->dt.usb_icl_ua); |
| if (rc < 0) |
| chip->dt.usb_icl_ua = SMB138X_DEFAULT_ICL_UA; |
| |
| rc = of_property_read_u32(node, |
| "qcom,dc-icl-ua", &chip->dt.dc_icl_ua); |
| if (rc < 0) |
| chip->dt.dc_icl_ua = SMB138X_DEFAULT_ICL_UA; |
| |
| rc = of_property_read_u32(node, |
| "qcom,charger-temp-max-mdegc", |
| &chip->dt.chg_temp_max_mdegc); |
| if (rc < 0) |
| chip->dt.chg_temp_max_mdegc = 80000; |
| |
| rc = of_property_read_u32(node, |
| "qcom,connector-temp-max-mdegc", |
| &chip->dt.connector_temp_max_mdegc); |
| if (rc < 0) |
| chip->dt.connector_temp_max_mdegc = 105000; |
| |
| return 0; |
| } |
| |
| /************************ |
| * USB PSY REGISTRATION * |
| ************************/ |
| |
| static enum power_supply_property smb138x_usb_props[] = { |
| POWER_SUPPLY_PROP_PRESENT, |
| POWER_SUPPLY_PROP_ONLINE, |
| POWER_SUPPLY_PROP_VOLTAGE_MIN, |
| POWER_SUPPLY_PROP_VOLTAGE_MAX, |
| POWER_SUPPLY_PROP_VOLTAGE_NOW, |
| POWER_SUPPLY_PROP_CURRENT_MAX, |
| POWER_SUPPLY_PROP_TYPE, |
| POWER_SUPPLY_PROP_TYPEC_MODE, |
| POWER_SUPPLY_PROP_TYPEC_POWER_ROLE, |
| POWER_SUPPLY_PROP_TYPEC_CC_ORIENTATION, |
| }; |
| |
| static int smb138x_usb_get_prop(struct power_supply *psy, |
| enum power_supply_property prop, |
| union power_supply_propval *val) |
| { |
| struct smb138x *chip = power_supply_get_drvdata(psy); |
| struct smb_charger *chg = &chip->chg; |
| int rc = 0; |
| |
| switch (prop) { |
| case POWER_SUPPLY_PROP_PRESENT: |
| rc = smblib_get_prop_usb_present(chg, val); |
| break; |
| case POWER_SUPPLY_PROP_ONLINE: |
| rc = smblib_get_prop_usb_online(chg, val); |
| break; |
| case POWER_SUPPLY_PROP_VOLTAGE_MIN: |
| val->intval = chg->voltage_min_uv; |
| break; |
| case POWER_SUPPLY_PROP_VOLTAGE_MAX: |
| val->intval = chg->voltage_max_uv; |
| break; |
| case POWER_SUPPLY_PROP_VOLTAGE_NOW: |
| rc = smblib_get_prop_usb_voltage_now(chg, val); |
| break; |
| case POWER_SUPPLY_PROP_CURRENT_MAX: |
| rc = smblib_get_prop_usb_current_max(chg, val); |
| break; |
| case POWER_SUPPLY_PROP_TYPE: |
| val->intval = chg->usb_psy_desc.type; |
| break; |
| case POWER_SUPPLY_PROP_TYPEC_MODE: |
| rc = smblib_get_prop_typec_mode(chg, val); |
| break; |
| case POWER_SUPPLY_PROP_TYPEC_POWER_ROLE: |
| rc = smblib_get_prop_typec_power_role(chg, val); |
| break; |
| case POWER_SUPPLY_PROP_TYPEC_CC_ORIENTATION: |
| rc = smblib_get_prop_typec_cc_orientation(chg, val); |
| break; |
| default: |
| pr_err("get prop %d is not supported\n", prop); |
| return -EINVAL; |
| } |
| |
| if (rc < 0) { |
| pr_debug("Couldn't get prop %d rc = %d\n", prop, rc); |
| return -ENODATA; |
| } |
| |
| return rc; |
| } |
| |
| static int smb138x_usb_set_prop(struct power_supply *psy, |
| enum power_supply_property prop, |
| const union power_supply_propval *val) |
| { |
| struct smb138x *chip = power_supply_get_drvdata(psy); |
| struct smb_charger *chg = &chip->chg; |
| int rc = 0; |
| |
| switch (prop) { |
| case POWER_SUPPLY_PROP_VOLTAGE_MIN: |
| rc = smblib_set_prop_usb_voltage_min(chg, val); |
| break; |
| case POWER_SUPPLY_PROP_VOLTAGE_MAX: |
| rc = smblib_set_prop_usb_voltage_max(chg, val); |
| break; |
| case POWER_SUPPLY_PROP_CURRENT_MAX: |
| rc = smblib_set_prop_usb_current_max(chg, val); |
| break; |
| case POWER_SUPPLY_PROP_TYPEC_POWER_ROLE: |
| rc = smblib_set_prop_typec_power_role(chg, val); |
| break; |
| default: |
| pr_err("set prop %d is not supported\n", prop); |
| return -EINVAL; |
| } |
| |
| return rc; |
| } |
| |
| static int smb138x_usb_prop_is_writeable(struct power_supply *psy, |
| enum power_supply_property prop) |
| { |
| switch (prop) { |
| case POWER_SUPPLY_PROP_TYPEC_POWER_ROLE: |
| return 1; |
| default: |
| break; |
| } |
| |
| return 0; |
| } |
| |
| static int smb138x_init_usb_psy(struct smb138x *chip) |
| { |
| struct power_supply_config usb_cfg = {}; |
| struct smb_charger *chg = &chip->chg; |
| |
| chg->usb_psy_desc.name = "usb"; |
| chg->usb_psy_desc.type = POWER_SUPPLY_TYPE_UNKNOWN; |
| chg->usb_psy_desc.properties = smb138x_usb_props; |
| chg->usb_psy_desc.num_properties = ARRAY_SIZE(smb138x_usb_props); |
| chg->usb_psy_desc.get_property = smb138x_usb_get_prop; |
| chg->usb_psy_desc.set_property = smb138x_usb_set_prop; |
| chg->usb_psy_desc.property_is_writeable = smb138x_usb_prop_is_writeable; |
| |
| usb_cfg.drv_data = chip; |
| usb_cfg.of_node = chg->dev->of_node; |
| chg->usb_psy = devm_power_supply_register(chg->dev, |
| &chg->usb_psy_desc, |
| &usb_cfg); |
| if (IS_ERR(chg->usb_psy)) { |
| pr_err("Couldn't register USB power supply\n"); |
| return PTR_ERR(chg->usb_psy); |
| } |
| |
| return 0; |
| } |
| |
| /************************* |
| * BATT PSY REGISTRATION * |
| *************************/ |
| |
| static enum power_supply_property smb138x_batt_props[] = { |
| POWER_SUPPLY_PROP_INPUT_SUSPEND, |
| POWER_SUPPLY_PROP_STATUS, |
| POWER_SUPPLY_PROP_HEALTH, |
| POWER_SUPPLY_PROP_PRESENT, |
| POWER_SUPPLY_PROP_CHARGE_TYPE, |
| POWER_SUPPLY_PROP_CAPACITY, |
| POWER_SUPPLY_PROP_CHARGER_TEMP, |
| POWER_SUPPLY_PROP_CHARGER_TEMP_MAX, |
| POWER_SUPPLY_PROP_SET_SHIP_MODE, |
| }; |
| |
| static int smb138x_batt_get_prop(struct power_supply *psy, |
| enum power_supply_property prop, |
| union power_supply_propval *val) |
| { |
| struct smb138x *chip = power_supply_get_drvdata(psy); |
| struct smb_charger *chg = &chip->chg; |
| int rc = 0; |
| |
| switch (prop) { |
| case POWER_SUPPLY_PROP_STATUS: |
| rc = smblib_get_prop_batt_status(chg, val); |
| break; |
| case POWER_SUPPLY_PROP_HEALTH: |
| rc = smblib_get_prop_batt_health(chg, val); |
| break; |
| case POWER_SUPPLY_PROP_PRESENT: |
| rc = smblib_get_prop_batt_present(chg, val); |
| break; |
| case POWER_SUPPLY_PROP_INPUT_SUSPEND: |
| rc = smblib_get_prop_input_suspend(chg, val); |
| break; |
| case POWER_SUPPLY_PROP_CHARGE_TYPE: |
| rc = smblib_get_prop_batt_charge_type(chg, val); |
| break; |
| case POWER_SUPPLY_PROP_CAPACITY: |
| rc = smblib_get_prop_batt_capacity(chg, val); |
| break; |
| case POWER_SUPPLY_PROP_CHARGER_TEMP: |
| rc = smb138x_get_prop_charger_temp(chip, val); |
| break; |
| case POWER_SUPPLY_PROP_CHARGER_TEMP_MAX: |
| rc = smblib_get_prop_charger_temp_max(chg, val); |
| break; |
| case POWER_SUPPLY_PROP_SET_SHIP_MODE: |
| /* Not in ship mode as long as device is active */ |
| val->intval = 0; |
| break; |
| default: |
| pr_err("batt power supply get prop %d not supported\n", prop); |
| return -EINVAL; |
| } |
| |
| if (rc < 0) { |
| pr_debug("Couldn't get prop %d rc = %d\n", prop, rc); |
| return -ENODATA; |
| } |
| |
| return rc; |
| } |
| |
| static int smb138x_batt_set_prop(struct power_supply *psy, |
| enum power_supply_property prop, |
| const union power_supply_propval *val) |
| { |
| struct smb138x *chip = power_supply_get_drvdata(psy); |
| struct smb_charger *chg = &chip->chg; |
| int rc = 0; |
| |
| switch (prop) { |
| case POWER_SUPPLY_PROP_INPUT_SUSPEND: |
| rc = smblib_set_prop_input_suspend(chg, val); |
| break; |
| case POWER_SUPPLY_PROP_CAPACITY: |
| rc = smblib_set_prop_batt_capacity(chg, val); |
| break; |
| case POWER_SUPPLY_PROP_SET_SHIP_MODE: |
| /* Not in ship mode as long as the device is active */ |
| if (!val->intval) |
| break; |
| rc = smblib_set_prop_ship_mode(chg, val); |
| break; |
| default: |
| pr_err("batt power supply set prop %d not supported\n", prop); |
| return -EINVAL; |
| } |
| |
| return rc; |
| } |
| |
| static int smb138x_batt_prop_is_writeable(struct power_supply *psy, |
| enum power_supply_property prop) |
| { |
| switch (prop) { |
| case POWER_SUPPLY_PROP_INPUT_SUSPEND: |
| case POWER_SUPPLY_PROP_CAPACITY: |
| return 1; |
| default: |
| break; |
| } |
| |
| return 0; |
| } |
| |
| static const struct power_supply_desc batt_psy_desc = { |
| .name = "battery", |
| .type = POWER_SUPPLY_TYPE_BATTERY, |
| .properties = smb138x_batt_props, |
| .num_properties = ARRAY_SIZE(smb138x_batt_props), |
| .get_property = smb138x_batt_get_prop, |
| .set_property = smb138x_batt_set_prop, |
| .property_is_writeable = smb138x_batt_prop_is_writeable, |
| }; |
| |
| static int smb138x_init_batt_psy(struct smb138x *chip) |
| { |
| struct power_supply_config batt_cfg = {}; |
| struct smb_charger *chg = &chip->chg; |
| int rc = 0; |
| |
| batt_cfg.drv_data = chip; |
| batt_cfg.of_node = chg->dev->of_node; |
| chg->batt_psy = devm_power_supply_register(chg->dev, |
| &batt_psy_desc, |
| &batt_cfg); |
| if (IS_ERR(chg->batt_psy)) { |
| pr_err("Couldn't register battery power supply\n"); |
| return PTR_ERR(chg->batt_psy); |
| } |
| |
| return rc; |
| } |
| |
| /***************************** |
| * PARALLEL PSY REGISTRATION * |
| *****************************/ |
| |
| static int smb1355_get_prop_connector_health(struct smb138x *chip) |
| { |
| struct smb_charger *chg = &chip->chg; |
| u8 temp; |
| int rc; |
| |
| rc = smblib_read(chg, SMB1355_TEMP_COMP_STATUS_REG, &temp); |
| if (rc < 0) { |
| pr_err("Couldn't read comp stat reg rc = %d\n", rc); |
| return POWER_SUPPLY_HEALTH_UNKNOWN; |
| } |
| |
| if (temp & SKIN_TEMP_RST_HOT_BIT) |
| return POWER_SUPPLY_HEALTH_OVERHEAT; |
| |
| if (temp & SKIN_TEMP_UB_HOT_BIT) |
| return POWER_SUPPLY_HEALTH_HOT; |
| |
| if (temp & SKIN_TEMP_LB_HOT_BIT) |
| return POWER_SUPPLY_HEALTH_WARM; |
| |
| return POWER_SUPPLY_HEALTH_COOL; |
| } |
| |
| static int smb138x_get_prop_connector_health(struct smb138x *chip) |
| { |
| struct smb_charger *chg = &chip->chg; |
| int rc, lb_mdegc, ub_mdegc, rst_mdegc, connector_mdegc; |
| |
| if (!chg->iio.connector_temp_chan || |
| PTR_ERR(chg->iio.connector_temp_chan) == -EPROBE_DEFER) |
| chg->iio.connector_temp_chan = iio_channel_get(chg->dev, |
| "connector_temp"); |
| |
| if (IS_ERR(chg->iio.connector_temp_chan)) |
| return POWER_SUPPLY_HEALTH_UNKNOWN; |
| |
| rc = iio_read_channel_processed(chg->iio.connector_temp_thr1_chan, |
| &lb_mdegc); |
| if (rc < 0) { |
| pr_err("Couldn't read connector lower bound rc=%d\n", rc); |
| return POWER_SUPPLY_HEALTH_UNKNOWN; |
| } |
| |
| rc = iio_read_channel_processed(chg->iio.connector_temp_thr2_chan, |
| &ub_mdegc); |
| if (rc < 0) { |
| pr_err("Couldn't read connector upper bound rc=%d\n", rc); |
| return POWER_SUPPLY_HEALTH_UNKNOWN; |
| } |
| |
| rc = iio_read_channel_processed(chg->iio.connector_temp_thr3_chan, |
| &rst_mdegc); |
| if (rc < 0) { |
| pr_err("Couldn't read connector reset bound rc=%d\n", rc); |
| return POWER_SUPPLY_HEALTH_UNKNOWN; |
| } |
| |
| rc = iio_read_channel_processed(chg->iio.connector_temp_chan, |
| &connector_mdegc); |
| if (rc < 0) { |
| pr_err("Couldn't read connector temperature rc=%d\n", rc); |
| return POWER_SUPPLY_HEALTH_UNKNOWN; |
| } |
| |
| if (connector_mdegc < lb_mdegc) |
| return POWER_SUPPLY_HEALTH_COOL; |
| else if (connector_mdegc < ub_mdegc) |
| return POWER_SUPPLY_HEALTH_WARM; |
| else if (connector_mdegc < rst_mdegc) |
| return POWER_SUPPLY_HEALTH_HOT; |
| |
| return POWER_SUPPLY_HEALTH_OVERHEAT; |
| } |
| |
| static enum power_supply_property smb138x_parallel_props[] = { |
| POWER_SUPPLY_PROP_CHARGE_TYPE, |
| POWER_SUPPLY_PROP_CHARGING_ENABLED, |
| POWER_SUPPLY_PROP_PIN_ENABLED, |
| POWER_SUPPLY_PROP_INPUT_SUSPEND, |
| POWER_SUPPLY_PROP_INPUT_CURRENT_LIMITED, |
| POWER_SUPPLY_PROP_VOLTAGE_MAX, |
| POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT_MAX, |
| POWER_SUPPLY_PROP_MODEL_NAME, |
| POWER_SUPPLY_PROP_PARALLEL_MODE, |
| POWER_SUPPLY_PROP_CONNECTOR_HEALTH, |
| POWER_SUPPLY_PROP_SET_SHIP_MODE, |
| POWER_SUPPLY_PROP_CHARGER_TEMP, |
| POWER_SUPPLY_PROP_CHARGER_TEMP_MAX, |
| POWER_SUPPLY_PROP_CURRENT_NOW, |
| POWER_SUPPLY_PROP_CURRENT_MAX, |
| }; |
| |
| static enum power_supply_property smb1355_parallel_props[] = { |
| POWER_SUPPLY_PROP_CHARGE_TYPE, |
| POWER_SUPPLY_PROP_CHARGING_ENABLED, |
| POWER_SUPPLY_PROP_PIN_ENABLED, |
| POWER_SUPPLY_PROP_INPUT_SUSPEND, |
| POWER_SUPPLY_PROP_INPUT_CURRENT_LIMITED, |
| POWER_SUPPLY_PROP_VOLTAGE_MAX, |
| POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT_MAX, |
| POWER_SUPPLY_PROP_MODEL_NAME, |
| POWER_SUPPLY_PROP_PARALLEL_MODE, |
| POWER_SUPPLY_PROP_CONNECTOR_HEALTH, |
| POWER_SUPPLY_PROP_SET_SHIP_MODE, |
| POWER_SUPPLY_PROP_CHARGER_TEMP, |
| POWER_SUPPLY_PROP_CHARGER_TEMP_MAX, |
| }; |
| |
| static int smb138x_parallel_get_prop(struct power_supply *psy, |
| enum power_supply_property prop, |
| union power_supply_propval *val) |
| { |
| struct smb138x *chip = power_supply_get_drvdata(psy); |
| struct smb_charger *chg = &chip->chg; |
| int rc = 0; |
| u8 temp; |
| |
| switch (prop) { |
| case POWER_SUPPLY_PROP_CHARGE_TYPE: |
| rc = smblib_get_prop_batt_charge_type(chg, val); |
| break; |
| case POWER_SUPPLY_PROP_CHARGING_ENABLED: |
| rc = smblib_read(chg, BATTERY_CHARGER_STATUS_5_REG, |
| &temp); |
| if (rc >= 0) |
| val->intval = (bool)(temp & CHARGING_ENABLE_BIT); |
| break; |
| case POWER_SUPPLY_PROP_PIN_ENABLED: |
| rc = smblib_read(chg, BATTERY_CHARGER_STATUS_5_REG, |
| &temp); |
| if (rc >= 0) |
| val->intval = !(temp & DISABLE_CHARGING_BIT); |
| break; |
| case POWER_SUPPLY_PROP_INPUT_SUSPEND: |
| rc = smblib_get_usb_suspend(chg, &val->intval); |
| break; |
| case POWER_SUPPLY_PROP_INPUT_CURRENT_LIMITED: |
| if ((chip->dt.pl_mode == POWER_SUPPLY_PL_USBIN_USBIN) |
| || (chip->dt.pl_mode == POWER_SUPPLY_PL_USBIN_USBIN_EXT)) |
| rc = smblib_get_prop_input_current_limited(chg, val); |
| else |
| val->intval = 0; |
| break; |
| case POWER_SUPPLY_PROP_VOLTAGE_MAX: |
| rc = smblib_get_charge_param(chg, &chg->param.fv, &val->intval); |
| break; |
| case POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT_MAX: |
| rc = smblib_get_charge_param(chg, &chg->param.fcc, |
| &val->intval); |
| break; |
| case POWER_SUPPLY_PROP_MODEL_NAME: |
| val->strval = chip->name; |
| break; |
| case POWER_SUPPLY_PROP_PARALLEL_MODE: |
| val->intval = chip->dt.pl_mode; |
| break; |
| case POWER_SUPPLY_PROP_CONNECTOR_HEALTH: |
| if (chip->pmic_rev_id->pmic_subtype != SMB1355_SUBTYPE) |
| val->intval = smb138x_get_prop_connector_health(chip); |
| else |
| val->intval = smb1355_get_prop_connector_health(chip); |
| break; |
| case POWER_SUPPLY_PROP_SET_SHIP_MODE: |
| /* Not in ship mode as long as device is active */ |
| val->intval = 0; |
| break; |
| case POWER_SUPPLY_PROP_CHARGER_TEMP: |
| if (chip->pmic_rev_id->pmic_subtype != SMB1355_SUBTYPE) |
| rc = smb138x_get_prop_charger_temp(chip, val); |
| else |
| rc = smblib_get_prop_charger_temp(chg, val); |
| break; |
| case POWER_SUPPLY_PROP_CHARGER_TEMP_MAX: |
| rc = smblib_get_prop_charger_temp_max(chg, val); |
| break; |
| case POWER_SUPPLY_PROP_CURRENT_NOW: |
| if (chip->pmic_rev_id->pmic_subtype != SMB1355_SUBTYPE) |
| rc = smblib_get_prop_slave_current_now(chg, val); |
| else |
| rc = -ENODATA; |
| break; |
| case POWER_SUPPLY_PROP_CURRENT_MAX: |
| if ((chip->pmic_rev_id->pmic_subtype != SMB1355_SUBTYPE) |
| && ((chip->dt.pl_mode == POWER_SUPPLY_PL_USBIN_USBIN) |
| || (chip->dt.pl_mode == POWER_SUPPLY_PL_USBIN_USBIN_EXT))) |
| rc = smblib_get_charge_param(chg, &chg->param.usb_icl, |
| &val->intval); |
| else |
| rc = -ENODATA; |
| break; |
| default: |
| pr_err("parallel power supply get prop %d not supported\n", |
| prop); |
| return -EINVAL; |
| } |
| |
| if (rc < 0) { |
| pr_debug("Couldn't get prop %d rc = %d\n", prop, rc); |
| return -ENODATA; |
| } |
| |
| return rc; |
| } |
| |
| static int smb138x_set_parallel_suspend(struct smb138x *chip, bool suspend) |
| { |
| struct smb_charger *chg = &chip->chg; |
| int rc = 0; |
| |
| rc = smblib_masked_write(chg, WD_CFG_REG, WDOG_TIMER_EN_BIT, |
| suspend ? 0 : WDOG_TIMER_EN_BIT); |
| if (rc < 0) { |
| pr_err("Couldn't %s watchdog rc=%d\n", |
| suspend ? "disable" : "enable", rc); |
| suspend = true; |
| } |
| |
| rc = smblib_masked_write(chg, USBIN_CMD_IL_REG, USBIN_SUSPEND_BIT, |
| suspend ? USBIN_SUSPEND_BIT : 0); |
| if (rc < 0) { |
| pr_err("Couldn't %s parallel charger rc=%d\n", |
| suspend ? "suspend" : "resume", rc); |
| return rc; |
| } |
| |
| return rc; |
| } |
| |
| static int smb138x_parallel_set_prop(struct power_supply *psy, |
| enum power_supply_property prop, |
| const union power_supply_propval *val) |
| { |
| struct smb138x *chip = power_supply_get_drvdata(psy); |
| struct smb_charger *chg = &chip->chg; |
| int rc = 0; |
| |
| switch (prop) { |
| case POWER_SUPPLY_PROP_INPUT_SUSPEND: |
| rc = smb138x_set_parallel_suspend(chip, (bool)val->intval); |
| break; |
| case POWER_SUPPLY_PROP_CURRENT_MAX: |
| if ((chip->dt.pl_mode == POWER_SUPPLY_PL_USBIN_USBIN) |
| || (chip->dt.pl_mode == POWER_SUPPLY_PL_USBIN_USBIN_EXT)) |
| rc = smblib_set_charge_param(chg, &chg->param.usb_icl, |
| val->intval); |
| break; |
| case POWER_SUPPLY_PROP_VOLTAGE_MAX: |
| rc = smblib_set_charge_param(chg, &chg->param.fv, val->intval); |
| break; |
| case POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT_MAX: |
| rc = smblib_set_charge_param(chg, &chg->param.fcc, val->intval); |
| break; |
| case POWER_SUPPLY_PROP_SET_SHIP_MODE: |
| /* Not in ship mode as long as the device is active */ |
| if (!val->intval) |
| break; |
| rc = smblib_set_prop_ship_mode(chg, val); |
| break; |
| default: |
| pr_debug("parallel power supply set prop %d not supported\n", |
| prop); |
| return -EINVAL; |
| } |
| |
| return rc; |
| } |
| |
| static int smb138x_parallel_prop_is_writeable(struct power_supply *psy, |
| enum power_supply_property prop) |
| { |
| return 0; |
| } |
| |
| static struct power_supply_desc parallel_psy_desc = { |
| .name = "parallel", |
| .type = POWER_SUPPLY_TYPE_PARALLEL, |
| .properties = smb138x_parallel_props, |
| .num_properties = ARRAY_SIZE(smb138x_parallel_props), |
| .get_property = smb138x_parallel_get_prop, |
| .set_property = smb138x_parallel_set_prop, |
| .property_is_writeable = smb138x_parallel_prop_is_writeable, |
| }; |
| |
| static int smb138x_init_parallel_psy(struct smb138x *chip) |
| { |
| struct power_supply_config parallel_cfg = {}; |
| struct smb_charger *chg = &chip->chg; |
| |
| parallel_cfg.drv_data = chip; |
| parallel_cfg.of_node = chg->dev->of_node; |
| chip->parallel_psy = devm_power_supply_register(chg->dev, |
| ¶llel_psy_desc, |
| ¶llel_cfg); |
| if (IS_ERR(chip->parallel_psy)) { |
| pr_err("Couldn't register parallel power supply\n"); |
| return PTR_ERR(chip->parallel_psy); |
| } |
| |
| return 0; |
| } |
| |
| static int smb1355_init_parallel_psy(struct smb138x *chip) |
| { |
| struct power_supply_config parallel_cfg = {}; |
| struct smb_charger *chg = &chip->chg; |
| |
| parallel_cfg.drv_data = chip; |
| parallel_cfg.of_node = chg->dev->of_node; |
| |
| /* change to smb1355's property list */ |
| parallel_psy_desc.properties = smb1355_parallel_props; |
| parallel_psy_desc.num_properties = ARRAY_SIZE(smb1355_parallel_props); |
| chip->parallel_psy = devm_power_supply_register(chg->dev, |
| ¶llel_psy_desc, |
| ¶llel_cfg); |
| if (IS_ERR(chip->parallel_psy)) { |
| pr_err("Couldn't register parallel power supply\n"); |
| return PTR_ERR(chip->parallel_psy); |
| } |
| |
| return 0; |
| } |
| |
| /****************************** |
| * VBUS REGULATOR REGISTRATION * |
| ******************************/ |
| |
| struct regulator_ops smb138x_vbus_reg_ops = { |
| .enable = smblib_vbus_regulator_enable, |
| .disable = smblib_vbus_regulator_disable, |
| .is_enabled = smblib_vbus_regulator_is_enabled, |
| }; |
| |
| static int smb138x_init_vbus_regulator(struct smb138x *chip) |
| { |
| struct smb_charger *chg = &chip->chg; |
| struct regulator_config cfg = {}; |
| int rc = 0; |
| |
| chg->vbus_vreg = devm_kzalloc(chg->dev, sizeof(*chg->vbus_vreg), |
| GFP_KERNEL); |
| if (!chg->vbus_vreg) |
| return -ENOMEM; |
| |
| cfg.dev = chg->dev; |
| cfg.driver_data = chip; |
| |
| chg->vbus_vreg->rdesc.owner = THIS_MODULE; |
| chg->vbus_vreg->rdesc.type = REGULATOR_VOLTAGE; |
| chg->vbus_vreg->rdesc.ops = &smb138x_vbus_reg_ops; |
| chg->vbus_vreg->rdesc.of_match = "qcom,smb138x-vbus"; |
| chg->vbus_vreg->rdesc.name = "qcom,smb138x-vbus"; |
| |
| chg->vbus_vreg->rdev = devm_regulator_register(chg->dev, |
| &chg->vbus_vreg->rdesc, &cfg); |
| if (IS_ERR(chg->vbus_vreg->rdev)) { |
| rc = PTR_ERR(chg->vbus_vreg->rdev); |
| chg->vbus_vreg->rdev = NULL; |
| if (rc != -EPROBE_DEFER) |
| pr_err("Couldn't register VBUS regualtor rc=%d\n", rc); |
| } |
| |
| return rc; |
| } |
| |
| /****************************** |
| * VCONN REGULATOR REGISTRATION * |
| ******************************/ |
| |
| struct regulator_ops smb138x_vconn_reg_ops = { |
| .enable = smblib_vconn_regulator_enable, |
| .disable = smblib_vconn_regulator_disable, |
| .is_enabled = smblib_vconn_regulator_is_enabled, |
| }; |
| |
| static int smb138x_init_vconn_regulator(struct smb138x *chip) |
| { |
| struct smb_charger *chg = &chip->chg; |
| struct regulator_config cfg = {}; |
| int rc = 0; |
| |
| chg->vconn_vreg = devm_kzalloc(chg->dev, sizeof(*chg->vconn_vreg), |
| GFP_KERNEL); |
| if (!chg->vconn_vreg) |
| return -ENOMEM; |
| |
| cfg.dev = chg->dev; |
| cfg.driver_data = chip; |
| |
| chg->vconn_vreg->rdesc.owner = THIS_MODULE; |
| chg->vconn_vreg->rdesc.type = REGULATOR_VOLTAGE; |
| chg->vconn_vreg->rdesc.ops = &smb138x_vconn_reg_ops; |
| chg->vconn_vreg->rdesc.of_match = "qcom,smb138x-vconn"; |
| chg->vconn_vreg->rdesc.name = "qcom,smb138x-vconn"; |
| |
| chg->vconn_vreg->rdev = devm_regulator_register(chg->dev, |
| &chg->vconn_vreg->rdesc, &cfg); |
| if (IS_ERR(chg->vconn_vreg->rdev)) { |
| rc = PTR_ERR(chg->vconn_vreg->rdev); |
| chg->vconn_vreg->rdev = NULL; |
| if (rc != -EPROBE_DEFER) |
| pr_err("Couldn't register VCONN regualtor rc=%d\n", rc); |
| } |
| |
| return rc; |
| } |
| |
| /*************************** |
| * HARDWARE INITIALIZATION * |
| ***************************/ |
| |
| #define MDEGC_3 3000 |
| #define MDEGC_15 15000 |
| static int smb138x_init_slave_hw(struct smb138x *chip) |
| { |
| struct smb_charger *chg = &chip->chg; |
| int rc; |
| |
| if (chip->wa_flags & OOB_COMP_WA_BIT) { |
| rc = smblib_masked_write(chg, SMB2CHG_MISC_ENG_SDCDC_CFG2, |
| ENG_SDCDC_SEL_OOB_VTH_BIT, |
| ENG_SDCDC_SEL_OOB_VTH_BIT); |
| if (rc < 0) { |
| pr_err("Couldn't configure the OOB comp threshold rc = %d\n", |
| rc); |
| return rc; |
| } |
| |
| rc = smblib_masked_write(chg, SMB2CHG_MISC_ENG_SDCDC_CFG6, |
| DEAD_TIME_MASK, HIGH_DEAD_TIME_MASK); |
| if (rc < 0) { |
| pr_err("Couldn't configure the sdcdc cfg 6 reg rc = %d\n", |
| rc); |
| return rc; |
| } |
| } |
| |
| /* enable watchdog bark and bite interrupts, and disable the watchdog */ |
| rc = smblib_masked_write(chg, WD_CFG_REG, WDOG_TIMER_EN_BIT |
| | WDOG_TIMER_EN_ON_PLUGIN_BIT | BITE_WDOG_INT_EN_BIT |
| | BARK_WDOG_INT_EN_BIT, |
| BITE_WDOG_INT_EN_BIT | BARK_WDOG_INT_EN_BIT); |
| if (rc < 0) { |
| pr_err("Couldn't configure the watchdog rc=%d\n", rc); |
| return rc; |
| } |
| |
| /* disable charging when watchdog bites */ |
| rc = smblib_masked_write(chg, SNARL_BARK_BITE_WD_CFG_REG, |
| BITE_WDOG_DISABLE_CHARGING_CFG_BIT, |
| BITE_WDOG_DISABLE_CHARGING_CFG_BIT); |
| if (rc < 0) { |
| pr_err("Couldn't configure the watchdog bite rc=%d\n", rc); |
| return rc; |
| } |
| |
| /* suspend parallel charging */ |
| rc = smb138x_set_parallel_suspend(chip, true); |
| if (rc < 0) { |
| pr_err("Couldn't suspend parallel charging rc=%d\n", rc); |
| return rc; |
| } |
| |
| /* initialize FCC to 0 */ |
| rc = smblib_set_charge_param(chg, &chg->param.fcc, 0); |
| if (rc < 0) { |
| pr_err("Couldn't set 0 FCC rc=%d\n", rc); |
| return rc; |
| } |
| |
| /* enable the charging path */ |
| rc = smblib_masked_write(chg, CHARGING_ENABLE_CMD_REG, |
| CHARGING_ENABLE_CMD_BIT, |
| CHARGING_ENABLE_CMD_BIT); |
| if (rc < 0) { |
| pr_err("Couldn't enable charging rc=%d\n", rc); |
| return rc; |
| } |
| |
| /* configure charge enable for software control; active high */ |
| rc = smblib_masked_write(chg, CHGR_CFG2_REG, |
| CHG_EN_POLARITY_BIT | CHG_EN_SRC_BIT, 0); |
| if (rc < 0) { |
| pr_err("Couldn't configure charge enable source rc=%d\n", |
| rc); |
| return rc; |
| } |
| |
| /* enable parallel current sensing */ |
| rc = smblib_masked_write(chg, CFG_REG, |
| VCHG_EN_CFG_BIT, VCHG_EN_CFG_BIT); |
| if (rc < 0) { |
| pr_err("Couldn't enable parallel current sensing rc=%d\n", |
| rc); |
| return rc; |
| } |
| |
| /* enable stacked diode */ |
| rc = smblib_write(chg, SMB2CHG_DC_TM_SREFGEN, STACKED_DIODE_EN_BIT); |
| if (rc < 0) { |
| pr_err("Couldn't enable stacked diode rc=%d\n", rc); |
| return rc; |
| } |
| |
| /* initialize charger temperature threshold */ |
| rc = iio_write_channel_processed(chg->iio.temp_max_chan, |
| chip->dt.chg_temp_max_mdegc); |
| if (rc < 0) { |
| pr_err("Couldn't set charger temp threshold rc=%d\n", rc); |
| return rc; |
| } |
| |
| rc = iio_write_channel_processed(chg->iio.connector_temp_thr1_chan, |
| chip->dt.connector_temp_max_mdegc); |
| if (rc < 0) { |
| pr_err("Couldn't set connector temp threshold1 rc=%d\n", rc); |
| return rc; |
| } |
| |
| rc = iio_write_channel_processed(chg->iio.connector_temp_thr2_chan, |
| chip->dt.connector_temp_max_mdegc + MDEGC_3); |
| if (rc < 0) { |
| pr_err("Couldn't set connector temp threshold2 rc=%d\n", rc); |
| return rc; |
| } |
| |
| rc = iio_write_channel_processed(chg->iio.connector_temp_thr3_chan, |
| chip->dt.connector_temp_max_mdegc + MDEGC_15); |
| if (rc < 0) { |
| pr_err("Couldn't set connector temp threshold3 rc=%d\n", rc); |
| return rc; |
| } |
| |
| rc = smblib_write(chg, THERMREG_SRC_CFG_REG, |
| THERMREG_SKIN_ADC_SRC_EN_BIT); |
| if (rc < 0) { |
| pr_err("Couldn't enable connector thermreg source rc=%d\n", rc); |
| return rc; |
| } |
| |
| return 0; |
| } |
| |
| static int smb138x_init_hw(struct smb138x *chip) |
| { |
| struct smb_charger *chg = &chip->chg; |
| int rc = 0; |
| |
| /* votes must be cast before configuring software control */ |
| vote(chg->dc_suspend_votable, |
| DEFAULT_VOTER, chip->dt.suspend_input, 0); |
| vote(chg->fcc_votable, |
| DEFAULT_VOTER, true, chip->dt.fcc_ua); |
| vote(chg->usb_icl_votable, |
| DCP_VOTER, true, chip->dt.usb_icl_ua); |
| vote(chg->dc_icl_votable, |
| DEFAULT_VOTER, true, chip->dt.dc_icl_ua); |
| |
| chg->dcp_icl_ua = chip->dt.usb_icl_ua; |
| |
| /* configure to a fixed 700khz freq to avoid tdie errors */ |
| rc = smblib_set_charge_param(chg, &chg->param.freq_buck, 700); |
| if (rc < 0) { |
| pr_err("Couldn't configure 700Khz switch freq rc=%d\n", rc); |
| return rc; |
| } |
| |
| /* configure charge enable for software control; active high */ |
| rc = smblib_masked_write(chg, CHGR_CFG2_REG, |
| CHG_EN_POLARITY_BIT | CHG_EN_SRC_BIT, 0); |
| if (rc < 0) { |
| pr_err("Couldn't configure charge enable source rc=%d\n", rc); |
| return rc; |
| } |
| |
| /* enable the charging path */ |
| rc = vote(chg->chg_disable_votable, DEFAULT_VOTER, false, 0); |
| if (rc < 0) { |
| pr_err("Couldn't enable charging rc=%d\n", rc); |
| return rc; |
| } |
| |
| /* |
| * trigger the usb-typec-change interrupt only when the CC state |
| * changes, or there was a VBUS error |
| */ |
| rc = smblib_write(chg, TYPE_C_INTRPT_ENB_REG, |
| TYPEC_CCSTATE_CHANGE_INT_EN_BIT |
| | TYPEC_VBUS_ERROR_INT_EN_BIT); |
| if (rc < 0) { |
| pr_err("Couldn't configure Type-C interrupts rc=%d\n", rc); |
| return rc; |
| } |
| |
| /* configure VCONN for software control */ |
| rc = smblib_masked_write(chg, TYPE_C_INTRPT_ENB_SOFTWARE_CTRL_REG, |
| VCONN_EN_SRC_BIT | VCONN_EN_VALUE_BIT, |
| VCONN_EN_SRC_BIT); |
| if (rc < 0) { |
| pr_err("Couldn't configure VCONN for SW control rc=%d\n", rc); |
| return rc; |
| } |
| |
| /* configure VBUS for software control */ |
| rc = smblib_masked_write(chg, OTG_CFG_REG, OTG_EN_SRC_CFG_BIT, 0); |
| if (rc < 0) { |
| pr_err("Couldn't configure VBUS for SW control rc=%d\n", rc); |
| return rc; |
| } |
| |
| /* configure power role for dual-role */ |
| rc = smblib_masked_write(chg, TYPE_C_INTRPT_ENB_SOFTWARE_CTRL_REG, |
| TYPEC_POWER_ROLE_CMD_MASK, 0); |
| if (rc < 0) { |
| pr_err("Couldn't configure power role for DRP rc=%d\n", rc); |
| return rc; |
| } |
| |
| if (chip->wa_flags & OOB_COMP_WA_BIT) { |
| rc = smblib_masked_write(chg, SMB2CHG_MISC_ENG_SDCDC_CFG2, |
| ENG_SDCDC_SEL_OOB_VTH_BIT, |
| ENG_SDCDC_SEL_OOB_VTH_BIT); |
| if (rc < 0) { |
| pr_err("Couldn't configure the OOB comp threshold rc = %d\n", |
| rc); |
| return rc; |
| } |
| |
| rc = smblib_masked_write(chg, SMB2CHG_MISC_ENG_SDCDC_CFG6, |
| DEAD_TIME_MASK, HIGH_DEAD_TIME_MASK); |
| if (rc < 0) { |
| pr_err("Couldn't configure the sdcdc cfg 6 reg rc = %d\n", |
| rc); |
| return rc; |
| } |
| } |
| |
| return rc; |
| } |
| |
| static int smb138x_setup_wa_flags(struct smb138x *chip) |
| { |
| struct device_node *revid_dev_node; |
| |
| revid_dev_node = of_parse_phandle(chip->chg.dev->of_node, |
| "qcom,pmic-revid", 0); |
| if (!revid_dev_node) { |
| pr_err("Missing qcom,pmic-revid property\n"); |
| return -EINVAL; |
| } |
| |
| chip->pmic_rev_id = get_revid_data(revid_dev_node); |
| if (IS_ERR_OR_NULL(chip->pmic_rev_id)) { |
| /* |
| * the revid peripheral must be registered, any failure |
| * here only indicates that the rev-id module has not |
| * probed yet. |
| */ |
| return -EPROBE_DEFER; |
| } |
| |
| switch (chip->pmic_rev_id->pmic_subtype) { |
| case SMB1381_SUBTYPE: |
| if (chip->pmic_rev_id->rev4 < 2) /* SMB1381 rev 1.0 */ |
| chip->wa_flags |= OOB_COMP_WA_BIT; |
| break; |
| default: |
| pr_err("PMIC subtype %d not supported\n", |
| chip->pmic_rev_id->pmic_subtype); |
| return -EINVAL; |
| } |
| |
| return 0; |
| } |
| |
| /**************************** |
| * DETERMINE INITIAL STATUS * |
| ****************************/ |
| |
| static irqreturn_t smb138x_handle_temperature_change(int irq, void *data) |
| { |
| struct smb_irq_data *irq_data = data; |
| struct smb138x *chip = irq_data->parent_data; |
| |
| power_supply_changed(chip->parallel_psy); |
| return IRQ_HANDLED; |
| } |
| |
| static int smb138x_determine_initial_slave_status(struct smb138x *chip) |
| { |
| struct smb_irq_data irq_data = {chip, "determine-initial-status"}; |
| |
| smb138x_handle_temperature_change(0, &irq_data); |
| return 0; |
| } |
| |
| static int smb138x_determine_initial_status(struct smb138x *chip) |
| { |
| struct smb_irq_data irq_data = {chip, "determine-initial-status"}; |
| |
| smblib_handle_usb_plugin(0, &irq_data); |
| smblib_handle_usb_typec_change(0, &irq_data); |
| smblib_handle_usb_source_change(0, &irq_data); |
| return 0; |
| } |
| |
| /************************** |
| * INTERRUPT REGISTRATION * |
| **************************/ |
| |
| static struct smb_irq_info smb138x_irqs[] = { |
| /* CHARGER IRQs */ |
| [CHG_ERROR_IRQ] = { |
| .name = "chg-error", |
| .handler = smblib_handle_debug, |
| }, |
| [CHG_STATE_CHANGE_IRQ] = { |
| .name = "chg-state-change", |
| .handler = smb138x_handle_slave_chg_state_change, |
| .wake = true, |
| }, |
| [STEP_CHG_STATE_CHANGE_IRQ] = { |
| .name = "step-chg-state-change", |
| .handler = smblib_handle_debug, |
| }, |
| [STEP_CHG_SOC_UPDATE_FAIL_IRQ] = { |
| .name = "step-chg-soc-update-fail", |
| .handler = smblib_handle_debug, |
| }, |
| [STEP_CHG_SOC_UPDATE_REQ_IRQ] = { |
| .name = "step-chg-soc-update-request", |
| .handler = smblib_handle_debug, |
| }, |
| /* OTG IRQs */ |
| [OTG_FAIL_IRQ] = { |
| .name = "otg-fail", |
| .handler = smblib_handle_debug, |
| }, |
| [OTG_OVERCURRENT_IRQ] = { |
| .name = "otg-overcurrent", |
| .handler = smblib_handle_debug, |
| }, |
| [OTG_OC_DIS_SW_STS_IRQ] = { |
| .name = "otg-oc-dis-sw-sts", |
| .handler = smblib_handle_debug, |
| }, |
| [TESTMODE_CHANGE_DET_IRQ] = { |
| .name = "testmode-change-detect", |
| .handler = smblib_handle_debug, |
| }, |
| /* BATTERY IRQs */ |
| [BATT_TEMP_IRQ] = { |
| .name = "bat-temp", |
| .handler = smblib_handle_batt_psy_changed, |
| }, |
| [BATT_OCP_IRQ] = { |
| .name = "bat-ocp", |
| .handler = smblib_handle_batt_psy_changed, |
| }, |
| [BATT_OV_IRQ] = { |
| .name = "bat-ov", |
| .handler = smblib_handle_batt_psy_changed, |
| }, |
| [BATT_LOW_IRQ] = { |
| .name = "bat-low", |
| .handler = smblib_handle_batt_psy_changed, |
| }, |
| [BATT_THERM_ID_MISS_IRQ] = { |
| .name = "bat-therm-or-id-missing", |
| .handler = smblib_handle_batt_psy_changed, |
| }, |
| [BATT_TERM_MISS_IRQ] = { |
| .name = "bat-terminal-missing", |
| .handler = smblib_handle_batt_psy_changed, |
| }, |
| /* USB INPUT IRQs */ |
| [USBIN_COLLAPSE_IRQ] = { |
| .name = "usbin-collapse", |
| .handler = smblib_handle_debug, |
| }, |
| [USBIN_LT_3P6V_IRQ] = { |
| .name = "usbin-lt-3p6v", |
| .handler = smblib_handle_debug, |
| }, |
| [USBIN_UV_IRQ] = { |
| .name = "usbin-uv", |
| .handler = smblib_handle_debug, |
| }, |
| [USBIN_OV_IRQ] = { |
| .name = "usbin-ov", |
| .handler = smblib_handle_debug, |
| }, |
| [USBIN_PLUGIN_IRQ] = { |
| .name = "usbin-plugin", |
| .handler = smblib_handle_usb_plugin, |
| }, |
| [USBIN_SRC_CHANGE_IRQ] = { |
| .name = "usbin-src-change", |
| .handler = smblib_handle_usb_source_change, |
| }, |
| [USBIN_ICL_CHANGE_IRQ] = { |
| .name = "usbin-icl-change", |
| .handler = smblib_handle_debug, |
| }, |
| [TYPE_C_CHANGE_IRQ] = { |
| .name = "type-c-change", |
| .handler = smblib_handle_usb_typec_change, |
| }, |
| /* DC INPUT IRQs */ |
| [DCIN_COLLAPSE_IRQ] = { |
| .name = "dcin-collapse", |
| .handler = smblib_handle_debug, |
| }, |
| [DCIN_LT_3P6V_IRQ] = { |
| .name = "dcin-lt-3p6v", |
| .handler = smblib_handle_debug, |
| }, |
| [DCIN_UV_IRQ] = { |
| .name = "dcin-uv", |
| .handler = smblib_handle_debug, |
| }, |
| [DCIN_OV_IRQ] = { |
| .name = "dcin-ov", |
| .handler = smblib_handle_debug, |
| }, |
| [DCIN_PLUGIN_IRQ] = { |
| .name = "dcin-plugin", |
| .handler = smblib_handle_debug, |
| }, |
| [DIV2_EN_DG_IRQ] = { |
| .name = "div2-en-dg", |
| .handler = smblib_handle_debug, |
| }, |
| [DCIN_ICL_CHANGE_IRQ] = { |
| .name = "dcin-icl-change", |
| .handler = smblib_handle_debug, |
| }, |
| /* MISCELLANEOUS IRQs */ |
| [WDOG_SNARL_IRQ] = { |
| .name = "wdog-snarl", |
| .handler = smblib_handle_debug, |
| }, |
| [WDOG_BARK_IRQ] = { |
| .name = "wdog-bark", |
| .handler = smblib_handle_wdog_bark, |
| .wake = true, |
| }, |
| [AICL_FAIL_IRQ] = { |
| .name = "aicl-fail", |
| .handler = smblib_handle_debug, |
| }, |
| [AICL_DONE_IRQ] = { |
| .name = "aicl-done", |
| .handler = smblib_handle_debug, |
| }, |
| [HIGH_DUTY_CYCLE_IRQ] = { |
| .name = "high-duty-cycle", |
| .handler = smblib_handle_debug, |
| }, |
| [INPUT_CURRENT_LIMIT_IRQ] = { |
| .name = "input-current-limiting", |
| .handler = smblib_handle_debug, |
| }, |
| [TEMPERATURE_CHANGE_IRQ] = { |
| .name = "temperature-change", |
| .handler = smb138x_handle_temperature_change, |
| }, |
| [SWITCH_POWER_OK_IRQ] = { |
| .name = "switcher-power-ok", |
| .handler = smblib_handle_debug, |
| }, |
| }; |
| |
| static int smb138x_get_irq_index_byname(const char *irq_name) |
| { |
| int i; |
| |
| for (i = 0; i < ARRAY_SIZE(smb138x_irqs); i++) { |
| if (strcmp(smb138x_irqs[i].name, irq_name) == 0) |
| return i; |
| } |
| |
| return -ENOENT; |
| } |
| |
| static int smb138x_request_interrupt(struct smb138x *chip, |
| struct device_node *node, |
| const char *irq_name) |
| { |
| struct smb_charger *chg = &chip->chg; |
| int rc = 0, irq, irq_index; |
| struct smb_irq_data *irq_data; |
| |
| irq = of_irq_get_byname(node, irq_name); |
| if (irq < 0) { |
| pr_err("Couldn't get irq %s byname\n", irq_name); |
| return irq; |
| } |
| |
| irq_index = smb138x_get_irq_index_byname(irq_name); |
| if (irq_index < 0) { |
| pr_err("%s is not a defined irq\n", irq_name); |
| return irq_index; |
| } |
| |
| if (!smb138x_irqs[irq_index].handler) |
| return 0; |
| |
| irq_data = devm_kzalloc(chg->dev, sizeof(*irq_data), GFP_KERNEL); |
| if (!irq_data) |
| return -ENOMEM; |
| |
| irq_data->parent_data = chip; |
| irq_data->name = irq_name; |
| irq_data->storm_data = smb138x_irqs[irq_index].storm_data; |
| mutex_init(&irq_data->storm_data.storm_lock); |
| |
| rc = devm_request_threaded_irq(chg->dev, irq, NULL, |
| smb138x_irqs[irq_index].handler, |
| IRQF_ONESHOT, irq_name, irq_data); |
| if (rc < 0) { |
| pr_err("Couldn't request irq %d\n", irq); |
| return rc; |
| } |
| |
| if (smb138x_irqs[irq_index].wake) |
| enable_irq_wake(irq); |
| |
| return rc; |
| } |
| |
| static int smb138x_request_interrupts(struct smb138x *chip) |
| { |
| struct smb_charger *chg = &chip->chg; |
| struct device_node *node = chg->dev->of_node; |
| struct device_node *child; |
| int rc = 0; |
| const char *name; |
| struct property *prop; |
| |
| for_each_available_child_of_node(node, child) { |
| of_property_for_each_string(child, "interrupt-names", |
| prop, name) { |
| rc = smb138x_request_interrupt(chip, child, name); |
| if (rc < 0) { |
| pr_err("Couldn't request interrupt %s rc=%d\n", |
| name, rc); |
| return rc; |
| } |
| } |
| } |
| |
| return rc; |
| } |
| |
| /********* |
| * PROBE * |
| *********/ |
| |
| static int smb138x_master_probe(struct smb138x *chip) |
| { |
| struct smb_charger *chg = &chip->chg; |
| int rc = 0; |
| |
| chg->param = v1_params; |
| |
| chip->name = "smb1381"; |
| rc = smblib_init(chg); |
| if (rc < 0) { |
| pr_err("Couldn't initialize smblib rc=%d\n", rc); |
| return rc; |
| } |
| |
| rc = smb138x_parse_dt(chip); |
| if (rc < 0) { |
| pr_err("Couldn't parse device tree rc=%d\n", rc); |
| return rc; |
| } |
| |
| rc = smb138x_init_vbus_regulator(chip); |
| if (rc < 0) { |
| pr_err("Couldn't initialize vbus regulator rc=%d\n", |
| rc); |
| return rc; |
| } |
| |
| rc = smb138x_init_vconn_regulator(chip); |
| if (rc < 0) { |
| pr_err("Couldn't initialize vconn regulator rc=%d\n", |
| rc); |
| return rc; |
| } |
| |
| rc = smb138x_init_usb_psy(chip); |
| if (rc < 0) { |
| pr_err("Couldn't initialize usb psy rc=%d\n", rc); |
| return rc; |
| } |
| |
| rc = smb138x_init_batt_psy(chip); |
| if (rc < 0) { |
| pr_err("Couldn't initialize batt psy rc=%d\n", rc); |
| return rc; |
| } |
| |
| rc = smb138x_init_hw(chip); |
| if (rc < 0) { |
| pr_err("Couldn't initialize hardware rc=%d\n", rc); |
| return rc; |
| } |
| |
| rc = smb138x_determine_initial_status(chip); |
| if (rc < 0) { |
| pr_err("Couldn't determine initial status rc=%d\n", |
| rc); |
| return rc; |
| } |
| |
| rc = smb138x_request_interrupts(chip); |
| if (rc < 0) { |
| pr_err("Couldn't request interrupts rc=%d\n", rc); |
| return rc; |
| } |
| |
| return rc; |
| } |
| |
| static int smb1355_slave_probe(struct smb138x *chip) |
| { |
| struct smb_charger *chg = &chip->chg; |
| int rc = 0; |
| |
| chg->param = v1_params; |
| |
| rc = smblib_init(chg); |
| if (rc < 0) { |
| pr_err("Couldn't initialize smblib rc=%d\n", rc); |
| goto cleanup; |
| } |
| |
| rc = smb138x_parse_dt(chip); |
| if (rc < 0) { |
| pr_err("Couldn't parse device tree rc=%d\n", rc); |
| goto cleanup; |
| } |
| |
| rc = smb138x_init_slave_hw(chip); |
| if (rc < 0) { |
| pr_err("Couldn't initialize hardware rc=%d\n", rc); |
| goto cleanup; |
| } |
| |
| rc = smb1355_init_parallel_psy(chip); |
| if (rc < 0) { |
| pr_err("Couldn't initialize parallel psy rc=%d\n", rc); |
| goto cleanup; |
| } |
| |
| rc = smb138x_determine_initial_slave_status(chip); |
| if (rc < 0) { |
| pr_err("Couldn't determine initial status rc=%d\n", rc); |
| goto cleanup; |
| } |
| |
| rc = smb138x_request_interrupts(chip); |
| if (rc < 0) { |
| pr_err("Couldn't request interrupts rc=%d\n", rc); |
| goto cleanup; |
| } |
| |
| return 0; |
| |
| cleanup: |
| smblib_deinit(chg); |
| return rc; |
| } |
| |
| static int smb1381_slave_probe(struct smb138x *chip) |
| { |
| struct smb_charger *chg = &chip->chg; |
| int rc = 0; |
| |
| chg->param = v1_params; |
| |
| rc = smblib_init(chg); |
| if (rc < 0) { |
| pr_err("Couldn't initialize smblib rc=%d\n", rc); |
| goto cleanup; |
| } |
| chg->iio.temp_max_chan = iio_channel_get(chg->dev, "charger_temp_max"); |
| if (IS_ERR(chg->iio.temp_max_chan)) { |
| rc = PTR_ERR(chg->iio.temp_max_chan); |
| goto cleanup; |
| } |
| |
| chg->iio.connector_temp_thr1_chan = iio_channel_get(chg->dev, |
| "connector_temp_thr1"); |
| if (IS_ERR(chg->iio.connector_temp_thr1_chan)) { |
| rc = PTR_ERR(chg->iio.connector_temp_thr1_chan); |
| goto cleanup; |
| } |
| |
| chg->iio.connector_temp_thr2_chan = iio_channel_get(chg->dev, |
| "connector_temp_thr2"); |
| if (IS_ERR(chg->iio.connector_temp_thr2_chan)) { |
| rc = PTR_ERR(chg->iio.connector_temp_thr2_chan); |
| goto cleanup; |
| } |
| |
| chg->iio.connector_temp_thr3_chan = iio_channel_get(chg->dev, |
| "connector_temp_thr3"); |
| if (IS_ERR(chg->iio.connector_temp_thr3_chan)) { |
| rc = PTR_ERR(chg->iio.connector_temp_thr3_chan); |
| goto cleanup; |
| } |
| |
| rc = smb138x_parse_dt(chip); |
| if (rc < 0) { |
| pr_err("Couldn't parse device tree rc=%d\n", rc); |
| goto cleanup; |
| } |
| |
| rc = smb138x_init_slave_hw(chip); |
| if (rc < 0) { |
| pr_err("Couldn't initialize hardware rc=%d\n", rc); |
| goto cleanup; |
| } |
| |
| if ((chip->dt.pl_mode == POWER_SUPPLY_PL_USBIN_USBIN) |
| || (chip->dt.pl_mode == POWER_SUPPLY_PL_USBIN_USBIN_EXT)) { |
| rc = smb138x_init_vbus_regulator(chip); |
| if (rc < 0) { |
| pr_err("Couldn't initialize vbus regulator rc=%d\n", |
| rc); |
| return rc; |
| } |
| } |
| |
| rc = smb138x_init_parallel_psy(chip); |
| if (rc < 0) { |
| pr_err("Couldn't initialize parallel psy rc=%d\n", rc); |
| goto cleanup; |
| } |
| |
| rc = smb138x_determine_initial_slave_status(chip); |
| if (rc < 0) { |
| pr_err("Couldn't determine initial status rc=%d\n", rc); |
| goto cleanup; |
| } |
| |
| rc = smb138x_request_interrupts(chip); |
| if (rc < 0) { |
| pr_err("Couldn't request interrupts rc=%d\n", rc); |
| goto cleanup; |
| } |
| |
| return 0; |
| |
| cleanup: |
| smblib_deinit(chg); |
| return rc; |
| } |
| |
| static int slave_probe(struct smb138x *chip) |
| { |
| struct device_node *revid_dev_node; |
| int rc = 0; |
| |
| revid_dev_node = of_parse_phandle(chip->chg.dev->of_node, |
| "qcom,pmic-revid", 0); |
| if (!revid_dev_node) { |
| pr_err("Missing qcom,pmic-revid property\n"); |
| return -EINVAL; |
| } |
| |
| chip->pmic_rev_id = get_revid_data(revid_dev_node); |
| if (IS_ERR_OR_NULL(chip->pmic_rev_id)) { |
| /* |
| * the revid peripheral must be registered, any failure |
| * here only indicates that the rev-id module has not |
| * probed yet. |
| */ |
| return -EPROBE_DEFER; |
| } |
| |
| switch (chip->pmic_rev_id->pmic_subtype) { |
| case SMB1355_SUBTYPE: |
| chip->name = "smb1355"; |
| rc = smb1355_slave_probe(chip); |
| break; |
| case SMB1381_SUBTYPE: |
| chip->name = "smb1381"; |
| rc = smb1381_slave_probe(chip); |
| break; |
| default: |
| pr_err("Unsupported pmic subtype = 0x%02x\n", |
| chip->pmic_rev_id->pmic_subtype); |
| rc = -EINVAL; |
| } |
| |
| if (rc < 0) { |
| if (rc != -EPROBE_DEFER) |
| pr_err("Couldn't probe SMB138X rc=%d\n", rc); |
| return rc; |
| } |
| |
| return 0; |
| } |
| |
| static const struct of_device_id match_table[] = { |
| { |
| .compatible = "qcom,smb138x-charger", |
| .data = (void *) PARALLEL_MASTER, |
| }, |
| { |
| .compatible = "qcom,smb138x-parallel-slave", |
| .data = (void *) PARALLEL_SLAVE, |
| }, |
| { |
| .compatible = "qcom,smb1355-parallel-slave", |
| .data = (void *) PARALLEL_SLAVE, |
| }, |
| { }, |
| }; |
| |
| static int smb138x_probe(struct platform_device *pdev) |
| { |
| struct smb138x *chip; |
| const struct of_device_id *id; |
| int rc = 0; |
| |
| chip = devm_kzalloc(&pdev->dev, sizeof(*chip), GFP_KERNEL); |
| if (!chip) |
| return -ENOMEM; |
| |
| chip->chg.dev = &pdev->dev; |
| chip->chg.debug_mask = &__debug_mask; |
| chip->chg.irq_info = smb138x_irqs; |
| chip->chg.name = "SMB"; |
| |
| chip->chg.regmap = dev_get_regmap(chip->chg.dev->parent, NULL); |
| if (!chip->chg.regmap) { |
| pr_err("parent regmap is missing\n"); |
| return -EINVAL; |
| } |
| |
| id = of_match_device(of_match_ptr(match_table), chip->chg.dev); |
| if (!id) { |
| pr_err("Couldn't find a matching device\n"); |
| return -ENODEV; |
| } |
| |
| platform_set_drvdata(pdev, chip); |
| |
| rc = smb138x_setup_wa_flags(chip); |
| if (rc < 0) { |
| if (rc != -EPROBE_DEFER) |
| pr_err("Couldn't setup wa flags rc = %d\n", rc); |
| return rc; |
| } |
| |
| chip->chg.mode = (enum smb_mode) id->data; |
| switch (chip->chg.mode) { |
| case PARALLEL_MASTER: |
| rc = smb138x_master_probe(chip); |
| break; |
| case PARALLEL_SLAVE: |
| rc = slave_probe(chip); |
| break; |
| default: |
| pr_err("Couldn't find a matching mode %d\n", chip->chg.mode); |
| rc = -EINVAL; |
| goto cleanup; |
| } |
| |
| if (rc < 0) { |
| if (rc != -EPROBE_DEFER) |
| pr_err("Couldn't probe SMB138X rc=%d\n", rc); |
| goto cleanup; |
| } |
| |
| pr_info("%s probed successfully mode=%d pl_mode = %d\n", |
| chip->name, chip->chg.mode, chip->dt.pl_mode); |
| return rc; |
| |
| cleanup: |
| platform_set_drvdata(pdev, NULL); |
| return rc; |
| } |
| |
| static int smb138x_remove(struct platform_device *pdev) |
| { |
| platform_set_drvdata(pdev, NULL); |
| return 0; |
| } |
| |
| static struct platform_driver smb138x_driver = { |
| .driver = { |
| .name = "qcom,smb138x-charger", |
| .owner = THIS_MODULE, |
| .of_match_table = match_table, |
| }, |
| .probe = smb138x_probe, |
| .remove = smb138x_remove, |
| }; |
| module_platform_driver(smb138x_driver); |
| |
| MODULE_DESCRIPTION("QPNP SMB138X Charger Driver"); |
| MODULE_LICENSE("GPL v2"); |