pata_hpt366: reimplement mode programming
Reimplement mode programming logic of pata_hpt366 such that it's
identical to that of IDE hpt366 driver. The differences were...
* pata_hpt366 used 0xCFFF8FFFF to mask pio modes and 0x3FFFFFFF dma
modes. IDE hpt366 uses 0xC1F8FFFF for PIO, 0x303800FF for MWDMA and
0x30070000 for UDMA.
* pata_hpt366 doesn't set 0x08000000 for PIO unless it's already set
and always turns it on for MWDMA/UDMA. IDE hpt366 doesn't bother
with the bit. It always uses what was there.
* IDE hpt366 always clears 0xC0000000. pata_hpt366 doesn't.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
diff --git a/drivers/ata/pata_hpt366.c b/drivers/ata/pata_hpt366.c
index e0c4f05..65c28e5 100644
--- a/drivers/ata/pata_hpt366.c
+++ b/drivers/ata/pata_hpt366.c
@@ -30,7 +30,7 @@
#define DRV_VERSION "0.6.2"
struct hpt_clock {
- u8 xfer_speed;
+ u8 xfer_mode;
u32 timing;
};
@@ -189,28 +189,6 @@
return ata_bmdma_mode_filter(adev, mask);
}
-/**
- * hpt36x_find_mode - reset the hpt36x bus
- * @ap: ATA port
- * @speed: transfer mode
- *
- * Return the 32bit register programming information for this channel
- * that matches the speed provided.
- */
-
-static u32 hpt36x_find_mode(struct ata_port *ap, int speed)
-{
- struct hpt_clock *clocks = ap->host->private_data;
-
- while(clocks->xfer_speed) {
- if (clocks->xfer_speed == speed)
- return clocks->timing;
- clocks++;
- }
- BUG();
- return 0xffffffffU; /* silence compiler warning */
-}
-
static int hpt36x_cable_detect(struct ata_port *ap)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
@@ -226,6 +204,49 @@
return ATA_CBL_PATA80;
}
+static void hpt366_set_mode(struct ata_port *ap, struct ata_device *adev,
+ u8 mode)
+{
+ struct hpt_clock *clocks = ap->host->private_data;
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+ u32 addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
+ u32 addr2 = 0x51 + 4 * ap->port_no;
+ u32 mask, reg;
+ u8 fast;
+
+ /* Fast interrupt prediction disable, hold off interrupt disable */
+ pci_read_config_byte(pdev, addr2, &fast);
+ if (fast & 0x80) {
+ fast &= ~0x80;
+ pci_write_config_byte(pdev, addr2, fast);
+ }
+
+ /* determine timing mask and find matching clock entry */
+ if (mode < XFER_MW_DMA_0)
+ mask = 0xc1f8ffff;
+ else if (mode < XFER_UDMA_0)
+ mask = 0x303800ff;
+ else
+ mask = 0x30070000;
+
+ while (clocks->xfer_mode) {
+ if (clocks->xfer_mode == mode)
+ break;
+ clocks++;
+ }
+ if (!clocks->xfer_mode)
+ BUG();
+
+ /*
+ * Combine new mode bits with old config bits and disable
+ * on-chip PIO FIFO/buffer (and PIO MST mode as well) to avoid
+ * problems handling I/O errors later.
+ */
+ pci_read_config_dword(pdev, addr1, ®);
+ reg = ((reg & ~mask) | (clocks->timing & mask)) & ~0xc0000000;
+ pci_write_config_dword(pdev, addr1, reg);
+}
+
/**
* hpt366_set_piomode - PIO setup
* @ap: ATA interface
@@ -236,28 +257,7 @@
static void hpt366_set_piomode(struct ata_port *ap, struct ata_device *adev)
{
- struct pci_dev *pdev = to_pci_dev(ap->host->dev);
- u32 addr1, addr2;
- u32 reg;
- u32 mode;
- u8 fast;
-
- addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
- addr2 = 0x51 + 4 * ap->port_no;
-
- /* Fast interrupt prediction disable, hold off interrupt disable */
- pci_read_config_byte(pdev, addr2, &fast);
- if (fast & 0x80) {
- fast &= ~0x80;
- pci_write_config_byte(pdev, addr2, fast);
- }
-
- pci_read_config_dword(pdev, addr1, ®);
- mode = hpt36x_find_mode(ap, adev->pio_mode);
- mode &= ~0x8000000; /* No FIFO in PIO */
- mode &= ~0x30070000; /* Leave config bits alone */
- reg &= 0x30070000; /* Strip timing bits */
- pci_write_config_dword(pdev, addr1, reg | mode);
+ hpt366_set_mode(ap, adev, adev->pio_mode);
}
/**
@@ -271,28 +271,7 @@
static void hpt366_set_dmamode(struct ata_port *ap, struct ata_device *adev)
{
- struct pci_dev *pdev = to_pci_dev(ap->host->dev);
- u32 addr1, addr2;
- u32 reg;
- u32 mode;
- u8 fast;
-
- addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
- addr2 = 0x51 + 4 * ap->port_no;
-
- /* Fast interrupt prediction disable, hold off interrupt disable */
- pci_read_config_byte(pdev, addr2, &fast);
- if (fast & 0x80) {
- fast &= ~0x80;
- pci_write_config_byte(pdev, addr2, fast);
- }
-
- pci_read_config_dword(pdev, addr1, ®);
- mode = hpt36x_find_mode(ap, adev->dma_mode);
- mode |= 0x8000000; /* FIFO in MWDMA or UDMA */
- mode &= ~0xC0000000; /* Leave config bits alone */
- reg &= 0xC0000000; /* Strip timing bits */
- pci_write_config_dword(pdev, addr1, reg | mode);
+ hpt366_set_mode(ap, adev, adev->dma_mode);
}
static struct scsi_host_template hpt36x_sht = {