ALSA: au88x0: pr_* replaced with dev_*
pr_* macros replaced with dev_* as they are more preffered over pr_*.
each file which had pr_* was reviewed manually and replaced with dev_*.
here we have actually used the reference of the vortex which was added
to some functions in the previous patch of this series.
The prefix of the CARD_NAME and prefix of "vortex:" was also
removed as the dev_* will print the device name.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
diff --git a/sound/pci/au88x0/au88x0.c b/sound/pci/au88x0/au88x0.c
index 21ce31f..e9c3833 100644
--- a/sound/pci/au88x0/au88x0.c
+++ b/sound/pci/au88x0/au88x0.c
@@ -48,11 +48,10 @@
{
int rc;
if (!(rc = pci_write_config_byte(vortex, 0x40, 0xff))) {
- pr_info( CARD_NAME
- ": vortex latency is 0xff\n");
+ dev_info(&vortex->dev, "vortex latency is 0xff\n");
} else {
- pr_warn( CARD_NAME
- ": could not set vortex latency: pci error 0x%x\n", rc);
+ dev_warn(&vortex->dev,
+ "could not set vortex latency: pci error 0x%x\n", rc);
}
}
@@ -70,11 +69,10 @@
if (!(rc = pci_read_config_byte(via, 0x42, &value))
&& ((value & 0x10)
|| !(rc = pci_write_config_byte(via, 0x42, value | 0x10)))) {
- pr_info( CARD_NAME
- ": bridge config is 0x%x\n", value | 0x10);
+ dev_info(&via->dev, "bridge config is 0x%x\n", value | 0x10);
} else {
- pr_warn( CARD_NAME
- ": could not set vortex latency: pci error 0x%x\n", rc);
+ dev_warn(&via->dev,
+ "could not set vortex latency: pci error 0x%x\n", rc);
}
}
@@ -97,7 +95,8 @@
PCI_DEVICE_ID_AMD_FE_GATE_7007, NULL);
}
if (via) {
- pr_info( CARD_NAME ": Activating latency workaround...\n");
+ dev_info(&vortex->dev,
+ "Activating latency workaround...\n");
vortex_fix_latency(vortex);
vortex_fix_agp_bridge(via);
}
@@ -153,7 +152,7 @@
return err;
if (pci_set_dma_mask(pci, DMA_BIT_MASK(32)) < 0 ||
pci_set_consistent_dma_mask(pci, DMA_BIT_MASK(32)) < 0) {
- pr_err( "error to set DMA mask\n");
+ dev_err(card->dev, "error to set DMA mask\n");
pci_disable_device(pci);
return -ENXIO;
}
@@ -182,7 +181,7 @@
chip->mmio = pci_ioremap_bar(pci, 0);
if (!chip->mmio) {
- pr_err( "MMIO area remap failed.\n");
+ dev_err(card->dev, "MMIO area remap failed.\n");
err = -ENOMEM;
goto ioremap_out;
}
@@ -191,14 +190,14 @@
* This must be done before we do request_irq otherwise we can get spurious
* interrupts that we do not handle properly and make a mess of things */
if ((err = vortex_core_init(chip)) != 0) {
- pr_err( "hw core init failed\n");
+ dev_err(card->dev, "hw core init failed\n");
goto core_out;
}
if ((err = request_irq(pci->irq, vortex_interrupt,
IRQF_SHARED, KBUILD_MODNAME,
chip)) != 0) {
- pr_err( "cannot grab irq\n");
+ dev_err(card->dev, "cannot grab irq\n");
goto irq_out;
}
chip->irq = pci->irq;
@@ -342,11 +341,11 @@
chip->rev = pci->revision;
#ifdef CHIP_AU8830
if ((chip->rev) != 0xfe && (chip->rev) != 0xfa) {
- pr_alert(
- "vortex: The revision (%x) of your card has not been seen before.\n",
+ dev_alert(card->dev,
+ "The revision (%x) of your card has not been seen before.\n",
chip->rev);
- pr_alert(
- "vortex: Please email the results of 'lspci -vv' to openvortex-dev@nongnu.org.\n");
+ dev_alert(card->dev,
+ "Please email the results of 'lspci -vv' to openvortex-dev@nongnu.org.\n");
snd_card_free(card);
err = -ENODEV;
return err;